arm64: dts: qcom: ipq5332: add few device nodes

Add the nodes for QUP peripheral, PRNG and WDOG. While at it, enable the
I2C device for MI01.2 board.

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230320104530.30411-3-quic_kathirav@quicinc.com

arm64: dts: qcom: sm8550: add ADSP audio codec macros

Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8550.  The nodes are very similar to SM8450, except missing
NPL clock which is not exposed on SM8550 and should not be touched.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230310134925.514125-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: Remove "iommus" property from PCIe nodes

Currently, most of the Qualcomm SoCs specify both "iommus" and "iommu-map"
properties for the PCIe nodes. First one passes the SMR mask to the iommu
driver and the latter specifies the SID for each PCIe device.

But with "iommus" property, the PCIe controller will be added to the
iommu group along with the devices. This makes no sense because the
controller will not initiate any DMA transaction on its own. And moreover,
it is not strictly required to pass the SMR mask to the iommu driver. If
the "iommus" property is not present, then the default mask of "0" would be
used which should work for all PCIe devices.

On the other side, if the SMR mask specified doesn't match the one expected
by the hypervisor, then all the PCIe transactions will end up triggering
"Unidentified Stream Fault" by the SMMU.

So to get rid of these hassles and also prohibit PCIe controllers from
adding to the iommu group, let's remove the "iommus" property from PCIe
nodes.

Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-arm-msm/20230227195535.GA749409-robh@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308075648.134119-1-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sm8450: simplify interrupts-extended

The parent controller for both interrupts is GIC, so no need for
interrupts-extended.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8250: simplify interrupts-extended

The parent controller for the interrupt is GIC, so no need for
interrupts-extended.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp: simplify interrupts-extended

The parent controller for both interrupts is GIC, so no need for
interrupts-extended.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8450: label the Soundwire nodes

Use labels, instead of comments, for Soundwire controllers.  Naming them
is useful, because they are specialized and have also naming in
datasheet/programming guide.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp: label the Soundwire nodes

Use labels, instead of comments, for Soundwire controllers.  Naming them
is useful, because they are specialized and have also naming in
datasheet/programming guide.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm6115: Use the correct DSI compatible

Use the non-deprecated, SoC-specific DSI compatible.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-9-70e13b1214fa@linaro.org

arm64: dts: qcom: sc8280xp-x13s: Add bluetooth

The Lenovo Thinkpad X13s has a WCN6855 Bluetooth controller on uart2,
add this.

Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326233812.28058-5-steev@kali.org

arm64: dts: qcom: sc8280xp: Define uart2

Add the definition for uart2 for sc8280xp devices.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326233812.28058-4-steev@kali.org

arm64: dts: qcom: sc8280xp: Add "mhi" region to the PCIe nodes

The "mhi" region contains the debug registers that could be used to monitor
the PCIe link transitions.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316081117.14288-19-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sm8250: Add "mhi" region to the PCIe nodes

The "mhi" region contains the debug registers that could be used to monitor
the PCIe link transitions.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316081117.14288-18-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sdm845: Add "mhi" region to the PCIe nodes

The "mhi" region contains the debug registers that could be used to monitor
the PCIe link transitions.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316081117.14288-17-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sa8775p-ride: set gpio-line-names for PMIC GPIOs

Set line names for GPIO lines exposed by PMICs on sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-16-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes

Add GPIO controller nodes to PMICs that have the GPIO hooked up on
sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-15-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pmic: add thermal zones

Add the thermal zones and associated alarm nodes for the PMICs that have
them hooked up on sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-12-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pmic: add support for the pmm8654 RESIN input

Add the RESIN input for sa8775p platforms' PMIC.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-11-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pmic: add the power key

Add the power key node under the PON node for PMIC #0 on sa8775p.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-10-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add the Power On device node

Add the PON node to PMIC #0 for sa8775p platforms.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-9-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add support for the on-board PMICs

Add a new .dtsi file for sa8775p PMICs and add the four PMICs interfaced
to the SoC via SPMI. Enable the PMICs for sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-8-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add the spmi node

Add the SPMI PMIC Arbiter node for SA8775p platforms.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-6-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add the pdc node

Add the Power Domain Controller node for SA8775p.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-5-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: sort soc nodes by reg property

Sort all children of the soc node by the first address in their reg
property. This was mostly already the case but there were some nodes
that didn't follow it so fix it now for consistency.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-3-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pad reg properties to 8 digits

The file has inconsistent padding of the address part of soc node
children's reg properties. Fix it.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-2-brgl@bgdev.pl

arm64: dts: qcom: sc8280xp: correct Soundwire wakeup interrupt name

The bindings expect second Soundwire interrupt to be "wakeup" (Linux
driver takes by index):

  sc8280xp-crd.dtb: soundwire-controller@3330000: interrupt-names:1: 'wakeup' was expected

Fixes: c18773d162a6 ("arm64: dts: qcom: sc8280xp: add SoundWire and LPASS")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403132328.61414-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845-tama: Enable GPI_DMA0/1

Enable both GPI DMAs.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-6-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Enable GPU

Enable the A630 GPU and its GMU.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-5-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Enable remoteprocs

Enable ADSP, CDSP and Venus.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-4-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Add regulator-system-load to l14a/l28a

Add the properties to ensure the ever so delicate touchscreen setup
matches downstream.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-3-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Add Synaptics Touchscreen

Add required pins and RMI4 node to the common DT and remove it
from Akatsuki, as it uses a different touch.

Since the panels are super high tech proprietary incell, they
need to be handled with very precise timings. As such the panel
driver sets up the power rails and GPIOs and the touchscreen
driver *has to* probe afterwards.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-2-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Add display nodes

Add required nodes to support display on XZ2/XZ2c. XZ3 has a
different power rail setup and needs to be handled separately.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-1-2b1567c039d7@linaro.org

arm64: dts: msm8953: Pad regs to 8 digits

Follow other dtses and pad regs to 8 digits.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-4-a39.skl@gmail.com

arm64: dts: msm8953: Drop unsupported dwc3 flag

Property phy_mode according to binding checker does not exist,
drop it.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-3-a39.skl@gmail.com

arm64: dts: msm8953: Provide dsi_phy clocks to gcc

Provide clocks from dsi_phy to gcc, this will make
sure we don't fallback to global name lookup.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-2-a39.skl@gmail.com

arm64: dts: msm8953: Replace xo_board with rpmcc sourced xo

Assign RPM_SMD_XO_CLK_SRC from rpmcc in place
of fixed-clock where possible.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-1-a39.skl@gmail.com

arm64: dts: qcom: sm8450: remove invalid properties in cluster-sleep nodes

Fixes the following DT bindings check error:
domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'
domain-idle-states: cluster-sleep-1: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-2-0ca1bea1a843@linaro.org

arm64: dts: qcom: sc8280xp: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name':

  sc8280xp-crd.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name' does not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8350: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm8350-mtp.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8150: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm8150-hdk.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm6375: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm6375-sony-xperia-murray-pdx225.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sdm845-shift-axolotl.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8250: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm8250-hdk.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm6375-pdx225: Add volume down GPIO key

Add the required nodes to enable the volume down key on the Sony
Xperia 10 IV.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-14-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Introduce C3 power state for both ARM clusters

Introduce the C3 power state, which - to the best of my understanding -
gates the CPU clock, but does not shut off the power rail.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-13-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Bump CPU rail power collapse index

In preparation for supporting a less-deep sleep state, rename the
existing rail power off from _0 to _1.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-12-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Configure TSENS thermal zones

Add a thermal zones configuration for all 15+11 TSENS sensors.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-11-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add TSENS

Add nodes for the two TSENS v2.8.0 controllers present on the SoC.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-10-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add CPUCP L3 node

Configure the L3 cache DVFS scaler within the CPUCP block to allow
for dynamic frequency switching.

Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-9-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add modem nodes

Add required nodes to make the embedded 5G modem boot up on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-8-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add wifi node

Add a node for ATH10K_SNoC wifi on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-7-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add IMEM

Add a node for the IMEM block on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-5-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add RPM sleep stats

Add a node for RPM sleep stats to enable sleep monitoring.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-4-708b8191f7eb@linaro.org

arm64: dts: qcom: sm8550: Use the correct BWMON fallback compatible

Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-7-77a050c2fbda@linaro.org

arm64: dts: qcom: sdm845: Use the correct BWMON compatible

Drop the incorrect msm8998 fallback and use the new qcom,sdm845-cpu-bwmon
compatible to distinguish the CPU BWMON found on this platform.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-6-77a050c2fbda@linaro.org

arm64: dts: qcom: sc8280xp: Use the correct BWMON fallback compatible

Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-5-77a050c2fbda@linaro.org

arm64: dts: qcom: sc7280: Use the correct BWMON fallback compatible

Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-4-77a050c2fbda@linaro.org

arm64: dts: qcom: sm6115: Add GPUCC and Adreno SMMU

Add GPUCC and Adreno SMMU nodes in preparation for adding the GPU
itself.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315-topic-kamorta_adrsmmu-v1-2-d1c0dea90bd9@linaro.org

Merge branch '20230208091340.124641-1-konrad.dybcio@linaro.org' into HEAD

Introduce SM6115 GPUCC devicetree bindings, to make it possible to use
clock defines in the devicetree source.

arm64: dts: qcom: msm8998-yoshino: Use actual pin names for pin nodes

With the gpio-line-names in place coming from SONY themselves, we can
now make the pin nodes and their labels to more closely resemble the
actual thing. 4k has been renamed to four_k due to dtc limitations.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314-topic-yoshino_gpio-v2-2-4cb80e187e38@linaro.org

arm64: dts: qcom: msm8998-yoshino: Use SONY GPIO names

Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the Yoshino devices DTs to better document the hardware.

Lilac and Poplar have identical pin assignments.
Diff between these two and maple:

TLMM:
-  "NC",
+  "TS_VDDIO_EN",

PMI8998:
-  "NC"
+  "USB_SWITCH_SEL"

-  "NC"
+  "4K_DISP_DCDC_EN"

PM8005:
-  "NC"
+  "EAR_EN"

Which is probably due to Maple being designed and released quite a bit
earlier than the other two and it having a super high tech true-4K
display.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314-topic-yoshino_gpio-v2-1-4cb80e187e38@linaro.org

arm64: dts: qcom: sdm845-xiaomi-beryllium: add notification LED

The Poco F1 has a single color white notification LED. Enable the
Qualcomm Light Pulse Generator (LPG) driver based notification LED.

Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313154226.136726-1-joelselvaraj.oss@gmail.com

arm64: dts: qcom: qdu1000: Add LLCC/system-cache-controller

Add a DT node for Last level cache (aka. system cache) controller
which provides control over the last level cache present on QDU1000
and QRU1000 SoCs.

Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313125731.17745-1-quic_kbajaj@quicinc.com

arm64: dts: qcom: apq8096-db820c: drop unit address from PMI8994 regulator

The PMIC regulators are not supposed to have unit addresses.

Fixes: 2317b87a2a6f ("arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-8-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8994-msft-lumia-octagon: drop unit address from PMI8994 regulator

The PMIC regulators are not supposed to have unit addresses.

Fixes: 60b214effb80 ("arm64: dts: qcom: msm8994-octagon: Configure regulators")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-7-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8994-kitakami: drop unit address from PMI8994 regulator

The PMIC regulators are not supposed to have unit addresses.

Fixes: e9783584c9b7 ("arm64: dts: qcom: msm8994-kitakami: Add VDD_GFX regulator")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8998-oneplus-cheeseburger: revert "fix backlight pin function"

This reverts commit 46546f28825cf3a5ef6873b9cf947cd85c8a7258 because it
mistakenly took PMIC pinctrl/GPIO as TLMM.  The TLMM pinctrl uses "gpio"
function, but PMIC uses "normal", so original code was correct:

  msm8998-oneplus-cheeseburger.dtb: pmic@2: gpio@c000:button-backlight-state: 'oneOf' conditional failed, one must be fixed:
    'gpio' is not one of ['normal', 'paired', 'func1', 'func2', 'dtest1', 'dtest2', 'dtest3', 'dtest4', 'func3', 'func4']

Fixes: 46546f28825c ("arm64: dts: qcom: msm8998-oneplus-cheeseburger: fix backlight pin function")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-trogdor-pazquel: correct trackpad supply

The hid-over-i2c takes VDD, not VCC supply.  Fix copy-pasta from other
boards which use elan,ekth3000 with valid VCC:

  sc7180-trogdor-pazquel360-lte.dtb: trackpad@15: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Fixes: fb69f6adaf88 ("arm64: dts: qcom: sc7180: Add pazquel dts files")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-trogdor-lazor: correct trackpad supply

The hid-over-i2c takes VDD, not VCC supply.  Fix copy-pasta from other
boards which use elan,ekth3000 with valid VCC:

  sc7180-trogdor-lazor-limozeen-nots-r4.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Fixes: 2c26adb8dbab ("arm64: dts: qcom: Add sc7180-lazor-limozeen skus")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7280-herobrine-villager: correct trackpad supply

The hid-over-i2c takes VDD, not VCC supply.  Fix copy-pasta from other
Herobrine boards which use elan,ekth3000 with valid VCC:

  sc7280-herobrine-villager-r1-lte.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Fixes: ee2a62116015 ("arm64: dts: qcom: sc7280: Add device tree for herobrine villager")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sda660-inforce: correct key node name

gpio-key bindings expect children to be named with generic prefix:

  sda660-inforce-ifc6560.dtb: gpio-keys: 'volup' does not match any of the regexes: ...

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8916-yiming-uz801v3: Add initial device tree

This commit adds support for the uz801 v3.0 WiFi/LTE dongle made by
Henan Yiming Technology Co., Ltd. based on MSM8916.

Note: The original firmware does not support 64-bit OS. It is necessary
to flash 64-bit TZ firmware to boot arm64.

Currently supported:
- All CPU cores
- Buttons
- LEDs
- Modem
- SDHC
- USB Device Mode
- UART

Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/tencent_62395CA0D608DD0078DD3D889F6E4E22BA05@qq.com

arm64: dts: qcom: msm8916: Move WCN compatible to boards

On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:

  - WCN3620  (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
  - WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
  - WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)

Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.

Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.

Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:

  - Boards with only &pronto { status = "okay"; } used the default
    "qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
  - Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
    already had an override that just moves to &wcnss_iris now.
  - For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
    boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
    so the definitions move to the board-specific DT part.

Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.

No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.

Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com

Merge branch 'arm64-fixes-for-6.3' into arm64-for-6.4

Merge the arm64-fixes-for-6.3 branch to avoid merge conflicts with
changes for v6.4.

arm64: dts: qcom: sdm845-xiaomi-beryllium: correct compatible

Tianma FHD panel is supposed to be used with fallback compatible:

  sdm845-xiaomi-beryllium-tianma.dtb: panel@0: compatible: ['tianma,fhd-video'] is too short

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-11-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845-xiaomi-beryllium: drop invalid panel properties

Panel does not have children with unit-addresses thus address/size-cells
are not valid:

  sdm845-xiaomi-beryllium-tianma.dtb: panel@0: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-10-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845-oneplus: drop invalid panel properties

Panel does not have children with unit-addresses thus address/size-cells
are not valid:

  panel@0: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-9-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-trogdor-lazor: correct panel compatible

innolux,n116bca-ea1 is not exactly compatible witg innolux,n116bge, as
they have their own driver data.  Bindings do not allow fallback:

  sc7180-trogdor-lazor-limozeen-nots-r4.dtb: panel: compatible: ['innolux,n116bca-ea1', 'innolux,n116bge'] is too long

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-8-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-qcard: use just "port" in panel

The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:

  sc7280-herobrine-zombie-nvme-lte.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-7-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-trogdor-wormdingler: use just "port" in panel

The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:

  sc7180-trogdor-wormdingler-rev1-boe.dtb: panel@0: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-trogdor-quackingstick: use just "port" in panel

The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:

  sc7180-trogdor-quackingstick-r0.dtb: panel@0: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-idp: use just "port" in panel

The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:

  sc7180-idp.dtb: panel@0: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'
  sc7180-idp.dtb: panel@0: 'port' is a required property

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp-crd: use just "port" in panel

The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:

  sc8280xp-crd.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp-lenovo-thinkpad-x13s: use just "port" in panel

The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:

  sc8280xp-lenovo-thinkpad-x13s.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845-cheza: use just "port" in Innolux panel

The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:

  sdm845-cheza-r2.dtb: panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326155753.92007-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp-pmics: fix pon compatible and registers

The pmk8280 PMIC PON peripheral is gen3 and uses two sets of registers;
hlos and pbs.

This specifically fixes the following error message during boot when the
pbs registers are not defined:

PON_PBS address missing, can't read HW debounce time

Note that this also enables the spurious interrupt workaround introduced
by commit 0b65118e6ba3 ("Input: pm8941-pwrkey - add software key press
debouncing support") (which may or may not be needed).

Fixes: ccd3517faf18 ("arm64: dts: qcom: sc8280xp: Add reference device")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Steev Klimaszewski <steev@kali.org> #Thinkpad X13s
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327122948.4323-1-johan+linaro@kernel.org

arm64: dts: qcom: sc8280xp-x13s: drop bogus 'input-enable'

The sc8280xp pin controller does not have a way to enable or disable the
input buffer so drop the unnecessary 'input-enable' property which is
about to be deprecated.

Link: https://lore.kernel.org/lkml/20230323102605.6.I291ce0ba2c6ea80b341659c4f75a567a76dd7ca6@changeid
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327123243.4527-1-johan+linaro@kernel.org

Merge branch '20230307062232.4889-1-quic_kathirav@quicinc.com' into arm64-for-6.4

Merge in the topic branch with IPQ5332 GCC DT-binding, to ensure that
the header file with GCC clock defines are available.

arm64: dts: qcom: sdm630: move DSI opp-table into DSI node

The soc node is supposed to have only device nodes with MMIO addresses,
so move the DSI OPP into the DSI controller node to fix:

  sda660-inforce-ifc6560.dtb: soc: opp-table-dsi: {'compatible': ['operating-points-v2'], ... should not be valid under {'type': 'object'}
    From schema: dtschema/schemas/simple-bus.yaml

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8996-xiaomi: drop simple-bus from clocks

'clocks' node is not a bus, but just a placeholder for clocks:

  msm8996-xiaomi-gemini.dtb: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
    From schema: dtschema/schemas/simple-bus.yaml
  msm8996-xiaomi-gemini.dtb: clocks: xo-board: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], ...
    From schema: dtschema/schemas/simple-bus.yaml

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8994-msft-lumia: drop simple-bus from clocks

'clocks' node is not a bus, but just a placeholder for clocks:

  msm8992-msft-lumia-octagon-talkman.dtb: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
    From schema: dtschema/schemas/simple-bus.yaml
  msm8992-msft-lumia-octagon-talkman.dtb: clocks: xo-board: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], ...
    From schema: dtschema/schemas/simple-bus.yaml

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: apq8096-db820c: drop simple-bus from clocks

'clocks' node is not a bus, but just a placeholder for clocks:

  apq8096-db820c.dtb: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
    From schema: dtschema/schemas/simple-bus.yaml
  apq8096-db820c.dtb: clocks: xo-board: {'compatible': ['fixed-clock'], '#clock-cells': [[0]],  ...
    From schema: dtschema/schemas/simple-bus.yaml

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8450: fix pcie1 gpios properties name

Add the final "s" to the pgio properties and fix the invalid "enable"
name to the correct "wake", checked against the HDK8450 schematics.

Fixes: bc6588bc25fb ("arm64: dts: qcom: sm8450: add PCIe1 root device")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-4-0ca1bea1a843@linaro.org

arm64: dts: qcom: sm8450: remove invalid power-domain-names in pcie nodes

Fixes the following DT bindings check error:
pci@1c00000: Unevaluated properties are not allowed ('power-domain-names' were unexpected)

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-3-0ca1bea1a843@linaro.org

arm64: dts: qcom: ipq8074-hk10: enable QMP device, not the PHY node

Correct PCIe PHY enablement to refer the QMP device nodes rather than
PHY device nodes. QMP nodes have 'status = "disabled"' property in the
ipq8074.dtsi, while PHY nodes do not correspond to the actual device and
do not have the status property.

Fixes: 1ed34da63a37 ("arm64: dts: qcom: Add board support for HK10")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324021651.1799969-2-dmitry.baryshkov@linaro.org

arm64: dts: qcom: ipq8074-hk01: enable QMP device, not the PHY node

Correct PCIe PHY enablement to refer the QMP device nodes rather than
PHY device nodes. QMP nodes have 'status = "disabled"' property in the
ipq8074.dtsi, while PHY nodes do not correspond to the actual device and
do not have the status property.

Fixes: e8a7fdc505bb ("arm64: dts: ipq8074: qcom: Re-arrange dts nodes based on address")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324021651.1799969-1-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sc8280xp-x13s: enable alternate touchpad

Enable both touchpad nodes in the devictree and let the HID driver
determine which one is actually populated (by attempting to read from
each i2c address).

Ideally this would not be needed and the boot firmware should instead
enable only the node for the populated touchpad, but this is unlikely to
ever be realised for the X13s.

Note that the pin configuration must currently be moved to the parent
i2c-bus node even though only one of these nodes will ever be
successfully probed on a specific device (e.g. to allow them to be
probed in parallel).

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324094744.20448-1-johan+linaro@kernel.org

arm64: dts: qcom: qrb5165-rb5: Use proper WSA881x shutdown GPIO polarity

The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed
DTS always comes with active high.  Since Linux drivers were updated to
handle proper flag, correct the DTS.

The change is not backwards compatible with older Linux kernel.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322193051.826167-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8250-mtp: Use proper WSA881x shutdown GPIO polarity

The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed
DTS always comes with active high.  Since Linux drivers were updated to
handle proper flag, correct the DTS.

The change is not backwards compatible with older Linux kernel.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322193051.826167-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm850-samsung-w737: Use proper WSA881x shutdown GPIO polarity

The WSA881x shutdown GPIO is active low (SD_N), but Linux driver assumed
DTS always comes with active high.  Since Linux drivers were updated to
handle proper flag, correct the DTS.

The change is not backwards compatible with older Linux kernel.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322193051.826167-3-krzysztof.kozlowski@linaro.org