arm64: dts: mediatek: mt8195: Set DSU PMU status to fail

[ Upstream commit d192615c307ec9f74cd0582880ece698533eb99b ]

The DSU PMU allows monitoring performance events in the DSU cluster,
which is done by configuring and reading back values from the DSU PMU
system registers. However, for write-access to be allowed by ELs lower
than EL3, the EL3 firmware needs to update the setting on the ACTLR3_EL3
register, as it is disallowed by default.

That configuration is not done on the firmware used by the MT8195 SoC,
as a consequence, booting a MT8195-based machine like
mt8195-cherry-tomato-r2 with CONFIG_ARM_DSU_PMU enabled hangs the kernel
just as it writes to the CLUSTERPMOVSCLR_EL1 register, since the
instruction faults to EL3, and BL31 apparently just re-runs the
instruction over and over.

Mark the DSU PMU node in the Devicetree with status "fail", as the
machine doesn't have a suitable firmware to make use of it from the
kernel, and allowing its driver to probe would hang the kernel.

Fixes: 37f2582883be ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230720200753.322133-1-nfraprado@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-5-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: sun4i_can: Only show Kconfig if ARCH_SUNXI is set

[ Upstream commit 1f223208ebdef84f21c15e9958c005a93c871aa2 ]

When adding the RISCV option I didn't gate it behind ARCH_SUNXI.
As a result this option shows up with Allwinner support isn't enabled.
Fix that by requiring ARCH_SUNXI to be set if RISCV is set.

Fixes: 8abb95250ae6 ("can: sun4i_can: Add support for the Allwinner D1")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/linux-sunxi/CAMuHMdV2m54UAH0X2dG7stEg=grFihrdsz4+o7=_DpBMhjTbkw@mail.gmail.com/
Signed-off-by: John Watts <contact@jookia.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20230905231342.2042759-2-contact@jookia.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: isotp: isotp_sendmsg(): fix TX state detection and wait behavior

[ Upstream commit d9c2ba65e651467de739324d978b04ed8729f483 ]

With patch [1], isotp_poll was updated to also queue the poller in the
so->wait queue, which is used for send state changes. Since the queue
now also contains polling tasks that are not interested in sending, the
queue fill state can no longer be used as an indication of send
readiness. As a consequence, nonblocking writes can lead to a race and
lock-up of the socket if there is a second task polling the socket in
parallel.

With this patch, isotp_sendmsg does not consult wq_has_sleepers but
instead tries to atomically set so->tx.state and waits on so->wait if it
is unable to do so. This behavior is in alignment with isotp_poll, which
also checks so->tx.state to determine send readiness.

V2:
- Revert direct exit to goto err_event_drop

[1] https://lore.kernel.org/all/20230331125511.372783-1-michal.sojka@cvut.cz

Reported-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Closes: https://lore.kernel.org/linux-can/11328958-453f-447f-9af8-3b5824dfb041@munic.io/
Signed-off-by: Lukas Magel <lukas.magel@posteo.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes: 79e19fa79cb5 ("can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events")
Link: https://github.com/pylessard/python-udsoncan/issues/178#issuecomment-1743786590
Link: https://lore.kernel.org/all/20230827092205.7908-1-lukas.magel@posteo.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: qca8k: fix potential MDIO bus conflict when accessing internal PHYs via management frames

[ Upstream commit 526c8ee04bdbd4d8d19a583b1f3b06700229a815 ]

Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).

We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.

Bisecting led to commit 2cd548566384 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.

Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.

My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:

           +---------+
      +----|         |
      |    | WAN PHY |
      | +--|         |
      | |  +---------+
      | |
      | |  +----------------------------------+
      | |  | QCA8337                          |
MDC   | |  |                        +-------+ |
------o-+--|--------o------------o--|       | |
MDIO    |  |        |            |  | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--|       | |
           |   |    |         |  |  +-------+ |
   | +-------------+  |  o--|       | |
   | | MDIO MDC    |  |  |  | PHY 2 |-|--to RJ45
eth1    | |             |  o--+--|       | |
-----------|-|port0        |  |  |  +-------+ |
           | |             |  |  o--|       | |
   | | switch core |  |  |  | PHY 3 |-|--to RJ45
           | +-------------+  o--+--|       | |
   |                  |  |  +-------+ |
   |                  |  o--|  ...  | |
   +----------------------------------+

When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.

Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.

Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: lynx-28g: serialize concurrent phy_set_mode_ext() calls to shared registers

[ Upstream commit 139ad1143151a07be93bf741d4ea7c89e59f89ce ]

The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.

Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.

Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: lynx-28g: lock PHY while performing CDR lock workaround

[ Upstream commit 0ac87fe54a171d18c5fb5345e3ee8d14e1b06f4b ]

lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset
the lane receiver if the CDR has not locked onto bit transitions in the
RX stream. But the PHY consumer may do stuff with the PHY simultaneously,
and that isn't okay. Block concurrent generic PHY calls by holding the
PHY mutex from this workqueue.

Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: lynx-28g: cancel the CDR check work item on the remove path

[ Upstream commit f200bab3756fe81493a1b280180dafa1d9ccdcf7 ]

The blamed commit added the CDR check work item but didn't cancel it on
the remove path. Fix this by adding a remove function which takes care
of it.

Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dp: Add newlines to debug printks

[ Upstream commit eba8c99a0fc45da1c8d5b5f5bd1dc2e79229a767 ]

These debug printks are missing newlines, causing drm debug logs to be
hard to read. Add newlines so that the messages are on their own line.

Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Cc: Vinod Polimera <quic_vpolimer@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 601f0479c583 ("drm/msm/dp: add logs across DP driver for ease of debugging")
Fixes: cd779808cccd ("drm/msm/dp: Add basic PSR support for eDP")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/554533/
Link: https://lore.kernel.org/r/20230825230109.2264345-1-swboyd@chromium.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dpu: change _dpu_plane_calc_bw() to use u64 to avoid overflow

[ Upstream commit 95e681ca3b65e4ce3d2537b47672d787b7d30375 ]

_dpu_plane_calc_bw() uses integer variables to calculate the bandwidth
used during plane bandwidth calculations. However for high resolution
displays this overflows easily and leads to below errors

[dpu error]crtc83 failed performance check -7

Promote the intermediate variables to u64 to avoid overflow.

changes in v2:
- change to u64 where actually needed in the math

Fixes: c33b7c0389e1 ("drm/msm/dpu: add support for clk and bw scaling for display")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Nia Espera <nespera@igalia.com>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/32
Tested-by: Nia Espera <nespera@igalia.com>
Patchwork: https://patchwork.freedesktop.org/patch/556288/
Link: https://lore.kernel.org/r/20230908012616.20654-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dsi: fix irq_of_parse_and_map() error checking

[ Upstream commit 6a1d4c7976dd1ee7c9f80bc8e62801ec7b1f2f58 ]

The irq_of_parse_and_map() function returns zero on error.  It
never returns negative error codes.  Fix the check.

Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/557715/
Link: https://lore.kernel.org/r/4f3c5c98-04f7-43f7-900f-5d7482c83eef@moroto.mountain
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dsi: skip the wait for video mode done if not applicable

[ Upstream commit ab483e3adcc178254eb1ce0fbdfbea65f86f1006 ]

dsi_wait4video_done() API waits for the DSI video mode engine to
become idle so that we can transmit the DCS commands in the
beginning of BLLP. However, with the current sequence, the MDP
timing engine is turned on after the panel's pre_enable() callback
which can send out the DCS commands needed to power up the panel.

During those cases, this API will always timeout and print out the
error spam leading to long bootup times and log flooding.

Fix this by checking if the DSI video engine was actually busy before
waiting for it to become idle otherwise this is a redundant wait.

changes in v2:
- move the reg read below the video mode check
- minor fixes in commit text

Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/34
Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/557853/
Link: https://lore.kernel.org/r/20230915204426.19011-1-quic_abhinavk@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dp: do not reinitialize phy unless retry during link training

[ Upstream commit 0c1a2e69bcb506f48ebf94bd199bab0b93f66da2 ]

DP PHY re-initialization done using dp_ctrl_reinitialize_mainlink() will
cause PLL unlocked initially and then PLL gets locked at the end of
initialization. PLL_UNLOCKED interrupt will fire during this time if the
interrupt mask is enabled.

However currently DP driver link training implementation incorrectly
re-initializes PHY unconditionally during link training as the PHY was
already configured in dp_ctrl_enable_mainlink_clocks().

Fix this by re-initializing the PHY only if the previous link training
failed.

[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy

Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/30
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/551847/
Link: https://lore.kernel.org/r/1691533190-19335-1-git-send-email-quic_khsieh@quicinc.com
[quic_abhinavk@quicinc.com: added line break in commit text]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: nuvoton: wpcm450: fix out of bounds write

[ Upstream commit 87d315a34133edcb29c4cadbf196ec6c30dfd47b ]

Write into 'pctrl->gpio_bank' happens before the check for GPIO index
validity, so out of bounds write may happen.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: a1d1e0e3d80a ("pinctrl: nuvoton: Add driver for WPCM450")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Reviewed-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20230825101532.6624-1-m.kobuk@ispras.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek - ALC287 merge RTK codec with CS CS35L41 AMP

[ Upstream commit d93eeca627db512a56145285dc94feac5b88a1d4 ]

This is merge model ALC287_FIXUP_THINKPAD_I2S_SPK and
ALC287_FIXUP_CS35L41_I2C_2_THINKPAD_ACPI.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Fixes: f7b069cf0881 ("ALSA: hda/realtek: Fix generic fixup definition for cs35l41 amp")
Link: https://lore.kernel.org/r/82a45234327c4c50b4988a27e9f64c37@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek - ALC287 I2S speaker platform support

[ Upstream commit e43252db7e207a2e194e6a4883a43a31a776a968 ]

0x17 was only speaker pin, DAC assigned will be 0x03. Headphone
assigned to 0x02.
Playback via headphone will get EQ filter processing. So,it needs to
swap DAC.

Tested-by: Mark Pearson <mpearson@lenovo.com>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4e4cfa1b3b4c46838aecafc6e8b6f876@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: d93eeca627db ("ALSA: hda/realtek - ALC287 merge RTK codec with CS CS35L41 AMP")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek: Add quirk for mute LEDs on HP ENVY x360 15-eu0xxx

[ Upstream commit c99c26b16c1544534ebd6a5f27a034f3e44d2597 ]

The LED for the mic mute button is controlled by GPIO2.
The mute button LED is slightly more complex, it's controlled by two bits
in coeff 0x0b.

Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/2693091.mvXUDI8C0e@fabians-envy
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: d93eeca627db ("ALSA: hda/realtek - ALC287 merge RTK codec with CS CS35L41 AMP")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek: Add quirk for HP Victus 16-d1xxx to enable mute LED

[ Upstream commit 93dc18e11b1ab2d485b69f91c973e6b83e47ebd0 ]

This quirk enables mute LED on HP Victus 16-d1xxx (8A25) laptops, which
use ALC245 codec.

Signed-off-by: SungHwan Jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20230823114051.3921-1-onenowy@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: d93eeca627db ("ALSA: hda/realtek - ALC287 merge RTK codec with CS CS35L41 AMP")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_sai: Don't disable bitclock for i.MX8MP

[ Upstream commit 197c53c8ecb34f2cd5922f4bdcffa8f701a134eb ]

On i.MX8MP, the BCE and TERE bit are binding with mclk
enablement, if BCE and TERE are cleared the MCLK also be
disabled on output pin, that cause the external codec (wm8960)
in wrong state.

Codec (wm8960) is using the mclk to generate PLL clock,
if mclk is disabled before disabling PLL, the codec (wm8960)
won't generate bclk and frameclk when sysclk switch to
MCLK source in next test case.

The test case:
$aplay -r44100 test1.wav (PLL source)
$aplay -r48000 test2.wav (MCLK source)
aplay: pcm_write:2127: write error: Input/output error

Fixes: 269f399dc19f ("ASoC: fsl_sai: Disable bit clock with transmitter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695116533-23287-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_sai: MCLK bind with TX/RX enable bit

[ Upstream commit 3e4a826129980fed0e3e746a7822f2f204dfc24a ]

On i.MX8MP, the sai MCLK is bound with TX/RX enable bit,
which means the TX/RE enable bit need to be enabled then
MCLK can be output on PAD.

Some codec (for example: WM8962) needs the MCLK output
earlier, otherwise there will be issue for codec
configuration.

Add new soc data "mclk_with_tere" for this platform and
enable the MCLK output in startup stage.

As "mclk_with_tere" only applied to i.MX8MP, currently
The soc data is shared with i.MX8MN, so need to add
an i.MX8MN own soc data with "mclk_with_tere" disabled.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683273322-2525-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org
Stable-dep-of: 197c53c8ecb3 ("ASoC: fsl_sai: Don't disable bitclock for i.MX8MP")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Use of_property_read_bool() for boolean properties

[ Upstream commit 2d2998b84330899bf88a0414f3356869be4a69eb ]

It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().

Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144733.1546413-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 197c53c8ecb3 ("ASoC: fsl_sai: Don't disable bitclock for i.MX8MP")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Intel: soc-acpi: Add entry for sof_es8336 in MTL match table.

commit 381ddcd5875e496f2eae06bb65853271b7150fee upstream.

Adding support for ES83x6 codec in MTL match table.

Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: sof_sdw: add support for SKU 0B14

commit fb0b8d299781be8d46b3612aa96cef28da0d93f4 upstream.

One more missing SKU in the list.

Closes: https://github.com/thesofproject/linux/issues/4543
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919092125.1922468-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: Intel: soc-acpi: Add entry for HDMI_In capture support in MTL match table

commit d1f67278d4b2de3bf544ea9bcd9f64d03584df87 upstream.

Adding HDMI-In capture via I2S feature support in MTL platform.

Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: simple-card-utils: fixup simple_util_startup() error handling

commit 69cf63b6560205a390a736b88d112374655adb28 upstream.

It should use "goto" instead of "return"

Fixes: 5ca2ab459817 ("ASoC: simple-card-utils: Add new system-clock-fixed flag")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/202309141205.ITZeDJxV-lkp@intel.com/
Closes: https://lore.kernel.org/all/202309151840.au9Aa2W4-lkp@intel.com/
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8c76jnz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: SOF: amd: fix for firmware reload failure after playback

commit 7e1fe5d9e7eae67e218f878195d1d348d01f9af7 upstream.

Setting ACP ACLK as clock source when ACP enters D0 state causing
firmware load failure as mentioned in below scenario.

- Load snd_sof_amd_rembrandt
- Play or Record audio
- Stop audio
- Unload snd_sof_amd_rembrandt
- Reload snd_sof_amd_rembrandt

If acp_clkmux_sel register field is set, then clock source will be
set to ACP ACLK when ACP enters D0 state.

During stream stop, if there is no active stream is running then
acp firmware will set the ACP ACLK value to zero.

When driver is reloaded and clock source is selected as ACP ACLK,
as ACP ACLK is programmed to zero, firmware loading will fail.

For RMB platform, remove the clock mux selection field so that
ACP will use internal clock source when ACP enters D0 state.

Fixes: 41cb85bc4b52 ("ASoC: SOF: amd: Add support for Rembrandt plaform.")
Reported-by: coolstar <coolstarorganization@gmail.com>
Closes: https://github.com/thesofproject/sof/issues/8137
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230927071412.2416250-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Change model for Intel RVP board

commit ccbd88be057a38531f835e8a04948ebf80cb0c5d upstream.

Intel RVP board (0x12cc) has Headset Mic issue for reboot.
If system plugged headset when system reboot the headset Mic was gone.

Fixes: 1a93f10c5b12 ("ALSA: hda/realtek: Add "Intel Reference board" and "NUC 13" SSID in the ALC256")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/28112f54c0c6496f97ac845645bc0256@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Fix microphone sound on Nexigo webcam.

commit 4a63e68a295187ae3c1cb3fa0c583c96a959714f upstream.

I own an external usb Webcam, model NexiGo N930AF, which had low mic volume and
inconsistent sound quality. Video works as expected.

(snip)
[  +0.047857] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[  +0.003406] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[  +0.000007] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[  +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[  +0.000004] usb 5-1: SerialNumber: 20201217011
[  +0.003900] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
[  +0.025726] usb 5-1: 3:1: cannot get usb sound sample rate freq at ep 0x86
[  +0.071482] usb 5-1: 3:2: cannot get usb sound sample rate freq at ep 0x86
[  +0.004679] usb 5-1: 3:3: cannot get usb sound sample rate freq at ep 0x86
[  +0.051607] usb 5-1: Warning! Unlikely big volume range (=4096), cval->res is probably wrong.
[  +0.000005] usb 5-1: [7] FU [Mic Capture Volume] ch = 1, val = 0/4096/1

Set up quirk cval->res to 16 for 256 levels,
Set GET_SAMPLE_RATE quirk flag to stop trying to get the sample rate.
Confirmed that happened anyway later due to the backoff mechanism, after 3 failures

All audio stream on device interfaces share the same values,
apart from wMaxPacketSize and tSamFreq :

(snip)
Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        3
      bAlternateSetting       3
      bNumEndpoints           1
      bInterfaceClass         1 Audio
      bInterfaceSubClass      2 Streaming
      bInterfaceProtocol      0
      iInterface              0
      AudioStreaming Interface Descriptor:
        bLength                 7
        bDescriptorType        36
        bDescriptorSubtype      1 (AS_GENERAL)
        bTerminalLink           8
        bDelay                  1 frames
        wFormatTag         0x0001 PCM
      AudioStreaming Interface Descriptor:
        bLength                11
        bDescriptorType        36
        bDescriptorSubtype      2 (FORMAT_TYPE)
        bFormatType             1 (FORMAT_TYPE_I)
        bNrChannels             1
        bSubframeSize           2
        bBitResolution         16
        bSamFreqType            1 Discrete
        tSamFreq[ 0]        44100
      Endpoint Descriptor:
        bLength                 9
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            5
          Transfer Type            Isochronous
          Synch Type               Asynchronous
          Usage Type               Data
        wMaxPacketSize     0x005c  1x 92 bytes
        bInterval               4
        bRefresh                0
        bSynchAddress           0
        AudioStreaming Endpoint Descriptor:
          bLength                 7
          bDescriptorType        37
          bDescriptorSubtype      1 (EP_GENERAL)
          bmAttributes         0x01
            Sampling Frequency
          bLockDelayUnits         0 Undefined
          wLockDelay         0x0000
(snip)

Based on the usb data about manufacturer, SPCA2281B3 is the most likely controller IC
Manufacturer does not provide link for datasheet nor detailed specs.
No way to confirm if the firmware supports any other way of getting the sample rate.

Testing patch provides consistent good sound recording quality and volume range.

(snip)
[  +0.045764] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[  +0.106290] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[  +0.000006] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[  +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[  +0.000004] usb 5-1: SerialNumber: 20201217011
[  +0.043700] usb 5-1: set resolution quirk: cval->res = 16
[  +0.002585] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)

Signed-off-by: Christos Skevis <xristos.thes@gmail.com>
Link: https://lore.kernel.org/r/20231006155330.399393-1-xristos.thes@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Fix microphone sound on Opencomm2 Headset

commit 6a83d6f3bb3c329a73e3483651fb77b78bac1878 upstream.

When a Opencomm2 Headset is connected to a Bluetooth USB dongle,
the audio playback functions properly, but the microphone does not work.

In the dmesg logs, there are messages indicating that the init_pitch
function fails when the capture process begins.

The microphone only functions when the ep pitch control is not set.

Toggling the pitch control off bypasses the init_piatch function
and allows the microphone to work.

Signed-off-by: WhaleChang <whalechang@google.com>
Link: https://lore.kernel.org/r/20231006044852.4181022-1-whalechang@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KEYS: trusted: Remove redundant static calls usage

commit 01bbafc63b65689cb179ca537971286bc27f3b74 upstream.

Static calls invocations aren't well supported from module __init and
__exit functions. Especially the static call from cleanup_trusted() led
to a crash on x86 kernel with CONFIG_DEBUG_VIRTUAL=y.

However, the usage of static call invocations for trusted_key_init()
and trusted_key_exit() don't add any value from either a performance or
security perspective. Hence switch to use indirect function calls instead.

Note here that although it will fix the current crash report, ultimately
the static call infrastructure should be fixed to either support its
future usage from module __init and __exit functions or not.

Reported-and-tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Link: https://lore.kernel.org/lkml/ZRhKq6e5nF%2F4ZIV1@fedora/#t
Fixes: 5d0682be3189 ("KEYS: trusted: Add generic trusted keys framework")
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip: renesas-rzg2l: Fix logic to clear TINT interrupt source

commit 9b8df572ba3f4e544366196820a719a40774433e upstream.

The logic to clear the TINT interrupt source in rzg2l_irqc_irq_disable()
is wrong as the mask is correct only for LSB on the TSSR register.
This issue is found when testing with two TINT interrupt sources. So fix
the logic for all TINTs by using the macro TSSEL_SHIFT() to multiply
tssr_offset with 8.

Fixes: 3fed09559cd8 ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230918122411.237635-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: interrupt-controller: renesas,rzg2l-irqc: Update description for '#interrupt-cells' property

commit cfa1f9db6d6088118ef311c0927c66072665b47e upstream.

Update description for '#interrupt-cells' property to utilize the
RZG2L_{NMI,IRQX} for the first cell defined in the
include/dt-bindings/interrupt-controller/irqc-rzg2l.h file.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 96fed779d3d4cb3c ("dt-bindings: interrupt-controller: Add Renesas RZ/G2L Interrupt Controller")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220722151155.21100-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: qcom: sm8150: extend the size of the PDC resource

commit cf5716acbfc6190b3f97f4614affdf5991aed7b2 upstream.

Follow the example of other platforms and extend the PDC resource region
to 0x30000, so that the PDC driver can read the PDC_VERSION register.

Fixes: 397ad94668c1 ("arm64: dts: qcom: sm8150: Add pdc interrupt controller node")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230905-topic-sm8x50-upstream-pdc-ver-v4-2-fc633c7df84b@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: prevent address rewrite in kernel_bind()

commit c889a99a21bf124c3db08d09df919f0eccc5ea4c upstream.

Similar to the change in commit 0bdf399342c5("net: Avoid address
overwrite in kernel_connect"), BPF hooks run on bind may rewrite the
address passed to kernel_bind(). This change

1) Makes a copy of the bind address in kernel_bind() to insulate
   callers.
2) Replaces direct calls to sock->ops->bind() in net with kernel_bind()

Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 4fbac77d2d09 ("bpf: Hooks for sys_bind")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ata: libata-scsi: Disable scsi device manage_system_start_stop

commit aa3998dbeb3abce63653b7f6d4542e7dcd022590 upstream.

The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.

For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.

However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.

Commit 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.

Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.

To do this, the following libata helper functions are introduced:

1) ata_dev_power_set_standby():

This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.

For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.

2) ata_dev_power_set_active() and

This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.

For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.

With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.

Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: amd: yc: Fix non-functional mic on Lenovo 82YM

commit 1948fa64727685ac3f6584755212e2e738b6b051 upstream.

Like the Lenovo 82TL, 82V2, 82QF and 82UG, the 82YM (Yoga 7 14ARP8)
requires an entry in the quirk list to enable the internal microphone.
The latter two received similar fixes in commit 1263cc0f414d
("ASoC: amd: yc: Fix non-functional mic on Lenovo 82QF and 82UG").

Fixes: c008323fe361 ("ASoC: amd: yc: Fix a non-functional mic on Lenovo 82SJ")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Frotscher <sven.frotscher@gmail.com>
Link: https://lore.kernel.org/r/20230927223758.18870-1-sven.frotscher@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

quota: Fix slow quotaoff

commit 869b6ea1609f655a43251bf41757aa44e5350a8f upstream.

Eric has reported that commit dabc8b207566 ("quota: fix dqput() to
follow the guarantees dquot_srcu should provide") heavily increases
runtime of generic/270 xfstest for ext4 in nojournal mode. The reason
for this is that ext4 in nojournal mode leaves dquots dirty until the last
dqput() and thus the cleanup done in quota_release_workfn() has to write
them all. Due to the way quota_release_workfn() is written this results
in synchronize_srcu() call for each dirty dquot which makes the dquot
cleanup when turning quotas off extremely slow.

To be able to avoid synchronize_srcu() for each dirty dquot we need to
rework how we track dquots to be cleaned up. Instead of keeping the last
dquot reference while it is on releasing_dquots list, we drop it right
away and mark the dquot with new DQ_RELEASING_B bit instead. This way we
can we can remove dquot from releasing_dquots list when new reference to
it is acquired and thus there's no need to call synchronize_srcu() each
time we drop dq_list_lock.

References: https://lore.kernel.org/all/ZRytn6CxFK2oECUt@debian-BULLSEYE-live-builder-AMD64
Reported-by: Eric Whitney <enwlinux@gmail.com>
Fixes: dabc8b207566 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: logitech-hidpp: Fix kernel crash on receiver USB disconnect

commit dac501397b9d81e4782232c39f94f4307b137452 upstream.

hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU)
races when it races with itself.

hidpp_connect_event() primarily runs from a workqueue but it also runs
on probe() and if a "device-connected" packet is received by the hw
when the thread running hidpp_connect_event() from probe() is waiting on
the hw, then a second thread running hidpp_connect_event() will be
started from the workqueue.

This opens the following races (note the below code is simplified):

1. Retrieving + printing the protocol (harmless race):

if (!hidpp->protocol_major) {
hidpp_root_get_protocol_version()
hidpp->protocol_major = response.rap.params[0];
}

We can actually see this race hit in the dmesg in the abrt output
attached to rhbz#2227968:

[ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
[ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.

Testing with extra logging added has shown that after this the 2 threads
take turn grabbing the hw access mutex (send_mutex) so they ping-pong
through all the other TOCTOU cases managing to hit all of them:

2. Updating the name to the HIDPP name (harmless race):

if (hidpp->name == hdev->name) {
...
hidpp->name = new_name;
}

3. Initializing the power_supply class for the battery (problematic!):

hidpp_initialize_battery()
{
        if (hidpp->battery.ps)
                return 0;

probe_battery(); /* Blocks, threads take turns executing this */

hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);

hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
   &hidpp->battery.desc, cfg);
}

4. Creating delayed input_device (potentially problematic):

if (hidpp->delayed_input)
return;

hidpp->delayed_input = hidpp_allocate_input(hdev);

The really big problem here is 3. Hitting the race leads to the following
sequence:

hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);

hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
   &hidpp->battery.desc, cfg);

...

hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);

hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
   &hidpp->battery.desc, cfg);

So now we have registered 2 power supplies for the same battery,
which looks a bit weird from userspace's pov but this is not even
the really big problem.

Notice how:

1. This is all devm-maganaged
2. The hidpp->battery.desc struct is shared between the 2 power supplies
3. hidpp->battery.desc.properties points to the result from the second
   devm_kmemdup()

This causes a use after free scenario on USB disconnect of the receiver:
1. The last registered power supply class device gets unregistered
2. The memory from the last devm_kmemdup() call gets freed,
   hidpp->battery.desc.properties now points to freed memory
3. The first registered power supply class device gets unregistered,
   this involves sending a remove uevent to userspace which invokes
   power_supply_uevent() to fill the uevent data
4. power_supply_uevent() uses hidpp->battery.desc.properties which
   now points to freed memory leading to backtraces like this one:

Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08
...
Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event
Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0
...
Sep 22 20:01:35 eric kernel:  ? asm_exc_page_fault+0x26/0x30
Sep 22 20:01:35 eric kernel:  ? power_supply_uevent+0xee/0x1d0
Sep 22 20:01:35 eric kernel:  ? power_supply_uevent+0x10d/0x1d0
Sep 22 20:01:35 eric kernel:  dev_uevent+0x10f/0x2d0
Sep 22 20:01:35 eric kernel:  kobject_uevent_env+0x291/0x680
Sep 22 20:01:35 eric kernel:  power_supply_unregister+0x8e/0xa0
Sep 22 20:01:35 eric kernel:  release_nodes+0x3d/0xb0
Sep 22 20:01:35 eric kernel:  devres_release_group+0xfc/0x130
Sep 22 20:01:35 eric kernel:  hid_device_remove+0x56/0xa0
Sep 22 20:01:35 eric kernel:  device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel:  bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel:  device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel:  ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel:  hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel:  logi_dj_remove+0x9a/0x100 [hid_logitech_dj 5c91534a0ead2b65e04dd799a0437e3b99b21bc4]
Sep 22 20:01:35 eric kernel:  hid_device_remove+0x44/0xa0
Sep 22 20:01:35 eric kernel:  device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel:  bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel:  device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel:  ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel:  hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel:  usbhid_disconnect+0x47/0x60 [usbhid 727dcc1c0b94e6b4418727a468398ac3bca492f3]
Sep 22 20:01:35 eric kernel:  usb_unbind_interface+0x90/0x270
Sep 22 20:01:35 eric kernel:  device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel:  bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel:  device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel:  ? kobject_put+0xa0/0x1d0
Sep 22 20:01:35 eric kernel:  usb_disable_device+0xcd/0x1e0
Sep 22 20:01:35 eric kernel:  usb_disconnect+0xde/0x2c0
Sep 22 20:01:35 eric kernel:  usb_disconnect+0xc3/0x2c0
Sep 22 20:01:35 eric kernel:  hub_event+0xe80/0x1c10

There have been quite a few bug reports (see Link tags) about this crash.

Fix all the TOCTOU issues, including the really bad power-supply related
system crash on USB disconnect, by making probe() use the workqueue for
running hidpp_connect_event() too, so that it can never run more then once.

Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227221
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2242189
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412#c58
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231005182638.3776-1-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: Do not rescan devices with a suspended queue

commit 626b13f015e080e434b1dee9a0c116ddbf4fb695 upstream.

Commit ff48b37802e5 ("scsi: Do not attempt to rescan suspended devices")
modified scsi_rescan_device() to avoid attempting rescanning a suspended
device. However, the modification added a check to verify that a SCSI
device is in the running state without checking if the device request
queue (in the case of block device) is also running, thus allowing the
exectuion of internal requests. Without checking the device request
queue, commit ff48b37802e5 fix is incomplete and deadlocks on resume can
still happen. Use blk_queue_pm_only() to check if the device request
queue allows executing commands in addition to checking the SCSI device
state.

Reported-by: Petr Tesarik <petr@tesarici.cz>
Fixes: ff48b37802e5 ("scsi: Do not attempt to rescan suspended devices")
Cc: stable@vger.kernel.org
Tested-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: hp-wmi:: Mark driver struct with __refdata to prevent section mismatch warning

[ Upstream commit 5b44abbc39ca15df80d0da4756078c98c831090f ]

As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning:

WARNING: modpost: drivers/platform/x86/hp/hp-wmi: section mismatch in reference: hp_wmi_driver+0x8 (section: .data) -> hp_wmi_bios_remove (section: .exit.text)

Fixes: c165b80cfecc ("hp-wmi: fix handling of platform device")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231004111624.2667753-1-u.kleine-koenig@pengutronix.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: think-lmi: Fix reference leak

[ Upstream commit 528ab3e605cabf2f9c9bd5944d3bfe15f6e94f81 ]

If a duplicate attribute is found using kset_find_obj(), a reference
to that attribute is returned which needs to be disposed accordingly
using kobject_put(). Move the setting name validation into a separate
function to allow for this change without having to duplicate the
cleanup code for this setting.
As a side note, a very similar bug was fixed in
commit 7295a996fdab ("platform/x86: dell-sysman: Fix reference leak"),
so it seems that the bug was copied from that driver.

Compile-tested only.

Fixes: 1bcad8e510b2 ("platform/x86: think-lmi: Fix issues with duplicate attributes")
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230925142819.74525-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf/arm-cmn: Fix the unhandled overflow status of counter 4 to 7

[ Upstream commit 7f949f6f54ff593123ab95b6247bfa4542a65580 ]

The register por_dt_pmovsr Bits[7:0] indicates overflow from counters 7
to 0. But in arm_cmn_handle_irq(), only handled the overflow status of
Bits[3:0] which results in unhandled overflow status of counters 4 to 7.

So let the overflow status of DTC counters 4 to 7 to be handled.

Fixes: 0ba64770a2f2 ("perf: Add Arm CMN-600 PMU driver")
Signed-off-by: Jing Zhang <renyu.zj@linux.alibaba.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1695612152-123633-1-git-send-email-renyu.zj@linux.alibaba.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/cxgb4: Check skb value for failure to allocate

[ Upstream commit 8fb8a82086f5bda6893ea6557c5a458e4549c6d7 ]

get_skb() can fail to allocate skb, so check it.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 5be78ee924ae ("RDMA/cxgb4: Fix LE hash collision bug for active open connection")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Link: https://lore.kernel.org/r/20230905124048.284165-1-artem.chernyshev@red-soft.ru
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915: Don't set PIPE_CONTROL_FLUSH_L3 for aux inval

[ Upstream commit 128c20eda73bd3e78505c574fb17adb46195c98b ]

PIPE_CONTROL_FLUSH_L3 is not needed for aux invalidation
so don't set that.

Fixes: 78a6ccd65fa3 ("drm/i915/gt: Ensure memory quiesced before invalidation")
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Tejas Upadhyay <tejas.upadhyay@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Cc: Tapani Pälli <tapani.palli@intel.com>
Cc: Mark Janes <mark.janes@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Tested-by: Tapani Pälli <tapani.palli@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926142401.25687-1-nirmoy.das@intel.com
(cherry picked from commit 03d681412b38558aefe4fb0f46e36efa94bb21ef)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: fix delegated action races

[ Upstream commit a5efdbcece83af94180e8d7c0a6e22947318499d ]

The delegated action infrastructure is prone to the following
race: different CPUs can try to schedule different delegated
actions on the same subflow at the same time.

Each of them will check different bits via mptcp_subflow_delegate(),
and will try to schedule the action on the related per-cpu napi
instance.

Depending on the timing, both can observe an empty delegated list
node, causing the same entry to be added simultaneously on two different
lists.

The root cause is that the delegated actions infra does not provide
a single synchronization point. Address the issue reserving an additional
bit to mark the subflow as scheduled for delegation. Acquiring such bit
guarantee the caller to own the delegated list node, and being able to
safely schedule the subflow.

Clear such bit only when the subflow scheduling is completed, ensuring
proper barrier in place.

Additionally swap the meaning of the delegated_action bitmask, to allow
the usage of the existing helper to set multiple bit at once.

Fixes: bcd97734318d ("mptcp: use delegate action to schedule 3rd ack retrans")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-1-28de4ac663ae@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mana: Fix TX CQE error handling

[ Upstream commit b2b000069a4c307b09548dc2243f31f3ca0eac9c ]

For an unknown TX CQE error type (probably from a newer hardware),
still free the SKB, update the queue tail, etc., otherwise the
accounting will be wrong.

Also, TX errors can be triggered by injecting corrupted packets, so
replace the WARN_ONCE to ratelimited error logging.

Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 6.1.58

Link: https://lore.kernel.org/r/20231012180030.112560642@linuxfoundation.org
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Ricardo B. Marliere <ricardo@marliere.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/test_meminit: fix off-by-one error in test_pages()

commit efb78fa86e95 ("lib/test_meminit: allocate pages up to order
MAX_ORDER") works great in kernels 6.4 and newer thanks to commit
23baf831a32c ("mm, treewide: redefine MAX_ORDER sanely"), but for older
kernels, the loop is off by one, which causes crashes when the test
runs.

Fix this up by changing "<= MAX_ORDER" "< MAX_ORDER" to allow the test
to work properly for older kernel branches.

Fixes: 421855d0d24d ("lib/test_meminit: allocate pages up to order MAX_ORDER")
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Xiaoke Wang <xkernel.wang@foxmail.com>
Cc: <stable@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "NFS: Fix error handling for O_DIRECT write scheduling"

This reverts commit f16fd0b11f0f4d41846b5102b1656ea1fc9ac7a0 which is
commit 954998b60caa8f2a3bf3abe490de6f08d283687a upstream.

There are reported NFS problems in the 6.1.56 release, so revert a set
of NFS patches to hopefully resolve the issue.

Reported-by: poester <poester@internetbrands.com>
Link: https://lore.kernel.org/r/20231012165439.137237-2-kernel@linuxace.com
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Link: https://lore.kernel.org/r/2023100755-livestock-barcode-fe41@gregkh
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "NFS: Fix O_DIRECT locking issues"

This reverts commit 4d98038e5bd939bd13cc4e602dfe60cd5110efa8 which is
commit 7c6339322ce0c6128acbe36aacc1eeb986dd7bf1 upstream.

There are reported NFS problems in the 6.1.56 release, so revert a set
of NFS patches to hopefully resolve the issue.

Reported-by: poester <poester@internetbrands.com>
Link: https://lore.kernel.org/r/20231012165439.137237-2-kernel@linuxace.com
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Link: https://lore.kernel.org/r/2023100755-livestock-barcode-fe41@gregkh
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "NFS: More O_DIRECT accounting fixes for error paths"

This reverts commit 1f49386d67792424028acfe781d466b010f8fa3f which is
commit 8982f7aff39fb526aba4441fff2525fcedd5e1a3 upstream.

There are reported NFS problems in the 6.1.56 release, so revert a set
of NFS patches to hopefully resolve the issue.

Reported-by: poester <poester@internetbrands.com>
Link: https://lore.kernel.org/r/20231012165439.137237-2-kernel@linuxace.com
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Link: https://lore.kernel.org/r/2023100755-livestock-barcode-fe41@gregkh
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "NFS: Use the correct commit info in nfs_join_page_group()"

This reverts commit d4729af1c73cfacb64facda3d196e25940f0e7a5 which is
commit b193a78ddb5ee7dba074d3f28dc050069ba083c0 upstream.

There are reported NFS problems in the 6.1.56 release, so revert a set
of NFS patches to hopefully resolve the issue.

Reported-by: poester <poester@internetbrands.com>
Link: https://lore.kernel.org/r/20231012165439.137237-2-kernel@linuxace.com
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Link: https://lore.kernel.org/r/2023100755-livestock-barcode-fe41@gregkh
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "NFS: More fixes for nfs_direct_write_reschedule_io()"

This reverts commit edd1f06145101dab83497806bb6162641255ef50 which is
commit b11243f720ee5f9376861099019c8542969b6318 upstream.

There are reported NFS problems in the 6.1.56 release, so revert a set
of NFS patches to hopefully resolve the issue.

Reported-by: poester <poester@internetbrands.com>
Link: https://lore.kernel.org/r/20231012165439.137237-2-kernel@linuxace.com
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Link: https://lore.kernel.org/r/2023100755-livestock-barcode-fe41@gregkh
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Anna Schumaker <Anna.Schumaker@Netapp.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 6.1.57

Link: https://lore.kernel.org/r/20231009130122.946357448@linuxfoundation.org
Tested-by: SeongJae Park <sj@kernel.org>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/events: replace evtchn_rwlock with RCU

commit 87797fad6cce28ec9be3c13f031776ff4f104cfc upstream.

In unprivileged Xen guests event handling can cause a deadlock with
Xen console handling. The evtchn_rwlock and the hvc_lock are taken in
opposite sequence in __hvc_poll() and in Xen console IRQ handling.
Normally this is no problem, as the evtchn_rwlock is taken as a reader
in both paths, but as soon as an event channel is being closed, the
lock will be taken as a writer, which will cause read_lock() to block:

CPU0                     CPU1                CPU2
(IRQ handling)           (__hvc_poll())      (closing event channel)

read_lock(evtchn_rwlock)
                         spin_lock(hvc_lock)
                                             write_lock(evtchn_rwlock)
                                                 [blocks]
spin_lock(hvc_lock)
    [blocks]
                        read_lock(evtchn_rwlock)
                            [blocks due to writer waiting,
                             and not in_interrupt()]

This issue can be avoided by replacing evtchn_rwlock with RCU in
xen_free_irq(). Note that RCU is used only to delay freeing of the
irq_info memory. There is no RCU based dereferencing or replacement of
pointers involved.

In order to avoid potential races between removing the irq_info
reference and handling of interrupts, set the irq_info pointer to NULL
only when freeing its memory. The IRQ itself must be freed at that
time, too, as otherwise the same IRQ number could be allocated again
before handling of the old instance would have been finished.

This is XSA-441 / CVE-2023-34324.

Fixes: 54c9de89895e ("xen/events: add a new "late EOI" evtchn framework")
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: remove one read_lock()/read_unlock() pair in rt6_check_neigh()

commit c486640aa710ddd06c13a7f7162126e1552e8842 upstream.

rt6_check_neigh() uses read_lock() to protect n->nud_state reading.

This seems overkill and causes false sharing.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: file_remove_privs needs an exclusive lock in direct io write

commit 9af86694fd5d387992699ec99007ed374966ce9a upstream.

This was noticed by Miklos that file_remove_privs might call into
notify_change(), which requires to hold an exclusive lock. The problem
exists in FUSE and btrfs. We can fix it without any additional helpers
from VFS, in case the privileges would need to be dropped, change the
lock type to be exclusive and redo the loop.

Fixes: e9adabb9712e ("btrfs: use shared lock for direct writes within EOF")
CC: Miklos Szeredi <miklos@szeredi.hu>
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netlink: remove the flex array from struct nlmsghdr

commit c73a72f4cbb47672c8cc7f7d7aba52f1cb15baca upstream.

I've added a flex array to struct nlmsghdr in
commit 738136a0e375 ("netlink: split up copies in the ack construction")
to allow accessing the data easily. It leads to warnings with clang,
if user space wraps this structure into another struct and the flex
array is not at the end of the container.

Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/all/20221114023927.GA685@u2004-local/
Link: https://lore.kernel.org/r/20221118033903.1651026-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix fscrypt name leak after failure to join log transaction

commit fee4c19937439693f2420a916169d08e88576e8e upstream.

When logging a new name, we don't expect to fail joining a log transaction
since we know at least one of the inodes was logged before in the current
transaction. However if we fail for some unexpected reason, we end up not
freeing the fscrypt name we previously allocated. So fix that by freeing
the name in case we failed to join a log transaction.

Fixes: ab3c5c18e8fa ("btrfs: setup qstr from dentrys using fscrypt helper")
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix an error handling path in btrfs_rename()

commit abe3bf7425fb695a9b37394af18b9ea58a800802 upstream.

If new_whiteout_inode() fails, some resources need to be freed.
Add the missing goto to the error handling path.

Fixes: ab3c5c18e8fa ("btrfs: setup qstr from dentrys using fscrypt helper")
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vrf: Fix lockdep splat in output path

commit 2033ab90380d46e0e9f0520fd6776a73d107fd95 upstream.

Cited commit converted the neighbour code to use the standard RCU
variant instead of the RCU-bh variant, but the VRF code still uses
rcu_read_lock_bh() / rcu_read_unlock_bh() around the neighbour lookup
code in its IPv4 and IPv6 output paths, resulting in lockdep splats
[1][2]. Can be reproduced using [3].

Fix by switching to rcu_read_lock() / rcu_read_unlock().

[1]
=============================
WARNING: suspicious RCU usage
6.5.0-rc1-custom-g9c099e6dbf98 #403 Not tainted
-----------------------------
include/net/neighbour.h:302 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
2 locks held by ping/183:
 #0: ffff888105ea1d80 (sk_lock-AF_INET){+.+.}-{0:0}, at: raw_sendmsg+0xc6c/0x33c0
 #1: ffffffff85b46820 (rcu_read_lock_bh){....}-{1:2}, at: vrf_output+0x2e3/0x2030

stack backtrace:
CPU: 0 PID: 183 Comm: ping Not tainted 6.5.0-rc1-custom-g9c099e6dbf98 #403
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc37 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0xc1/0xf0
 lockdep_rcu_suspicious+0x211/0x3b0
 vrf_output+0x1380/0x2030
 ip_push_pending_frames+0x125/0x2a0
 raw_sendmsg+0x200d/0x33c0
 inet_sendmsg+0xa2/0xe0
 __sys_sendto+0x2aa/0x420
 __x64_sys_sendto+0xe5/0x1c0
 do_syscall_64+0x38/0x80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

[2]
=============================
WARNING: suspicious RCU usage
6.5.0-rc1-custom-g9c099e6dbf98 #403 Not tainted
-----------------------------
include/net/neighbour.h:302 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
2 locks held by ping6/182:
 #0: ffff888114b63000 (sk_lock-AF_INET6){+.+.}-{0:0}, at: rawv6_sendmsg+0x1602/0x3e50
 #1: ffffffff85b46820 (rcu_read_lock_bh){....}-{1:2}, at: vrf_output6+0xe9/0x1310

stack backtrace:
CPU: 0 PID: 182 Comm: ping6 Not tainted 6.5.0-rc1-custom-g9c099e6dbf98 #403
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc37 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0xc1/0xf0
 lockdep_rcu_suspicious+0x211/0x3b0
 vrf_output6+0xd32/0x1310
 ip6_local_out+0xb4/0x1a0
 ip6_send_skb+0xbc/0x340
 ip6_push_pending_frames+0xe5/0x110
 rawv6_sendmsg+0x2e6e/0x3e50
 inet_sendmsg+0xa2/0xe0
 __sys_sendto+0x2aa/0x420
 __x64_sys_sendto+0xe5/0x1c0
 do_syscall_64+0x38/0x80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

[3]
#!/bin/bash

ip link add name vrf-red up numtxqueues 2 type vrf table 10
ip link add name swp1 up master vrf-red type dummy
ip address add 192.0.2.1/24 dev swp1
ip address add 2001:db8:1::1/64 dev swp1
ip neigh add 192.0.2.2 lladdr 00:11:22:33:44:55 nud perm dev swp1
ip neigh add 2001:db8:1::2 lladdr 00:11:22:33:44:55 nud perm dev swp1
ip vrf exec vrf-red ping 192.0.2.2 -c 1 &> /dev/null
ip vrf exec vrf-red ping6 2001:db8:1::2 -c 1 &> /dev/null

Fixes: 09eed1192cec ("neighbour: switch to standard rcu, instead of rcu_bh")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/netdev/CA+G9fYtEr-=GbcXNDYo3XOkwR+uYgehVoDjsP0pFLUpZ_AZcyg@mail.gmail.com/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230715153605.4068066-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: remove nexthop_fib6_nh_bh()

commit ef1148d4487438a3408d6face2a8360d91b4af70 upstream.

After blamed commit, nexthop_fib6_nh_bh() and nexthop_fib6_nh()
are the same.

Delete nexthop_fib6_nh_bh(), and convert /proc/net/ipv6_route
to standard rcu to avoid this splat:

[ 5723.180080] WARNING: suspicious RCU usage
[ 5723.180083] -----------------------------
[ 5723.180084] include/net/nexthop.h:516 suspicious rcu_dereference_check() usage!
[ 5723.180086]
other info that might help us debug this:

[ 5723.180087]
rcu_scheduler_active = 2, debug_locks = 1
[ 5723.180089] 2 locks held by cat/55856:
[ 5723.180091] #0: ffff9440a582afa8 (&p->lock){+.+.}-{3:3}, at: seq_read_iter (fs/seq_file.c:188)
[ 5723.180100] #1: ffffffffaac07040 (rcu_read_lock_bh){....}-{1:2}, at: rcu_lock_acquire (include/linux/rcupdate.h:326)
[ 5723.180109]
stack backtrace:
[ 5723.180111] CPU: 14 PID: 55856 Comm: cat Tainted: G S        I        6.3.0-dbx-DEV #528
[ 5723.180115] Call Trace:
[ 5723.180117]  <TASK>
[ 5723.180119] dump_stack_lvl (lib/dump_stack.c:107)
[ 5723.180124] dump_stack (lib/dump_stack.c:114)
[ 5723.180126] lockdep_rcu_suspicious (include/linux/context_tracking.h:122)
[ 5723.180132] ipv6_route_seq_show (include/net/nexthop.h:?)
[ 5723.180135] ? ipv6_route_seq_next (net/ipv6/ip6_fib.c:2605)
[ 5723.180140] seq_read_iter (fs/seq_file.c:272)
[ 5723.180145] seq_read (fs/seq_file.c:163)
[ 5723.180151] proc_reg_read (fs/proc/inode.c:316 fs/proc/inode.c:328)
[ 5723.180155] vfs_read (fs/read_write.c:468)
[ 5723.180160] ? up_read (kernel/locking/rwsem.c:1617)
[ 5723.180164] ksys_read (fs/read_write.c:613)
[ 5723.180168] __x64_sys_read (fs/read_write.c:621)
[ 5723.180170] do_syscall_64 (arch/x86/entry/common.c:?)
[ 5723.180174] entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
[ 5723.180177] RIP: 0033:0x7fa455677d2a

Fixes: 09eed1192cec ("neighbour: switch to standard rcu, instead of rcu_bh")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230510154646.370659-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Restore __ldcw_align for PA-RISC 2.0 processors

commit 914988e099fc658436fbd7b8f240160c352b6552 upstream.

Back in 2005, Kyle McMartin removed the 16-byte alignment for
ldcw semaphores on PA 2.0 machines (CONFIG_PA20). This broke
spinlocks on pre PA8800 processors. The main symptom was random
faults in mmap'd memory (e.g., gcc compilations, etc).

Unfortunately, the errata for this ldcw change is lost.

The issue is the 16-byte alignment required for ldcw semaphore
instructions can only be reduced to natural alignment when the
ldcw operation can be handled coherently in cache. Only PA8800
and PA8900 processors actually support doing the operation in
cache.

Aligning the spinlock dynamically adds two integer instructions
to each spinlock.

Tested on rp3440, c8000 and a500.

Signed-off-by: John David Anglin <dave.anglin@bell.net>
Link: https://lore.kernel.org/linux-parisc/6b332788-2227-127f-ba6d-55e99ecf4ed8@bell.net/T/#t
Link: https://lore.kernel.org/linux-parisc/20050609050702.GB4641@roadwarrior.mcmartin.ca/
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksmbd: fix uaf in smb20_oplock_break_ack

commit c69813471a1ec081a0b9bf0c6bd7e8afd818afce upstream.

drop reference after use opinfo.

Signed-off-by: luosili <rootlab@huawei.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksmbd: fix race condition between session lookup and expire

commit 53ff5cf89142b978b1a5ca8dc4d4425e6a09745f upstream.

 Thread A                        +  Thread B
 ksmbd_session_lookup            |  smb2_sess_setup
   sess = xa_load                |
                                 |
                                 |    xa_erase(&conn->sessions, sess->id);
                                 |
                                 |    ksmbd_session_destroy(sess) --> kfree(sess)
                                 |
   // UAF!                       |
   sess->last_active = jiffies   |
                                 +

This patch add rwsem to fix race condition between ksmbd_session_lookup
and ksmbd_expire_session.

Reported-by: luosili <rootlab@huawei.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/sev: Use the GHCB protocol when available for SNP CPUID requests

commit 6bc6f7d9d7ac3cdbe9e8b0495538b4a0cc11f032 upstream.

SNP retrieves the majority of CPUID information from the SNP CPUID page.
But there are times when that information needs to be supplemented by the
hypervisor, for example, obtaining the initial APIC ID of the vCPU from
leaf 1.

The current implementation uses the MSR protocol to retrieve the data from
the hypervisor, even when a GHCB exists. The problem arises when an NMI
arrives on return from the VMGEXIT. The NMI will be immediately serviced
and may generate a #VC requiring communication with the hypervisor.

Since a GHCB exists in this case, it will be used. As part of using the
GHCB, the #VC handler will write the GHCB physical address into the GHCB
MSR and the #VC will be handled.

When the NMI completes, processing resumes at the site of the VMGEXIT
which is expecting to read the GHCB MSR and find a CPUID MSR protocol
response. Since the NMI handling overwrote the GHCB MSR response, the
guest will see an invalid reply from the hypervisor and self-terminate.

Fix this problem by using the GHCB when it is available. Any NMI
received is properly handled because the GHCB contents are copied into
a backup page and restored on NMI exit, thus preserving the active GHCB
request or result.

  [ bp: Touchups. ]

Fixes: ee0bfa08a345 ("x86/compressed/64: Add support for SEV-SNP CPUID table in #VC handlers")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/a5856fa1ebe3879de91a8f6298b6bbd901c61881.1690578565.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/mlx5: Fix NULL string error

commit dab994bcc609a172bfdab15a0d4cb7e50e8b5458 upstream.

checkpath is complaining about NULL string, change it to 'Unknown'.

Fixes: 37aa5c36aa70 ("IB/mlx5: Add UARs write-combining and non-cached mapping")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Link: https://lore.kernel.org/r/8638e5c14fadbde5fa9961874feae917073af920.1695203958.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/mlx5: Fix mutex unlocking on error flow for steering anchor creation

commit 2fad8f06a582cd431d398a0b3f9be21d069603ab upstream.

The mutex was not unlocked on some of the error flows.
Moved the unlock location to include all the error flow scenarios.

Fixes: e1f4a52ac171 ("RDMA/mlx5: Create an indirect flow table for steering anchor")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Hamdan Igbaria <hamdani@nvidia.com>
Link: https://lore.kernel.org/r/1244a69d783da997c0af0b827c622eb00495492e.1695203958.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/siw: Fix connection failure handling

commit 53a3f777049771496f791504e7dc8ef017cba590 upstream.

In case immediate MPA request processing fails, the newly
created endpoint unlinks the listening endpoint and is
ready to be dropped. This special case was not handled
correctly by the code handling the later TCP socket close,
causing a NULL dereference crash in siw_cm_work_handler()
when dereferencing a NULL listener. We now also cancel
the useless MPA timeout, if immediate MPA request
processing fails.

This patch furthermore simplifies MPA processing in general:
Scheduling a useless TCP socket read in sk_data_ready() upcall
is now surpressed, if the socket is already moved out of
TCP_ESTABLISHED state.

Fixes: 6c52fdc244b5 ("rdma/siw: connection management")
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20230905145822.446263-1-bmt@zurich.ibm.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/srp: Do not call scsi_done() from srp_abort()

commit e193b7955dfad68035b983a0011f4ef3590c85eb upstream.

After scmd_eh_abort_handler() has called the SCSI LLD eh_abort_handler
callback, it performs one of the following actions:
* Call scsi_queue_insert().
* Call scsi_finish_command().
* Call scsi_eh_scmd_add().
Hence, SCSI abort handlers must not call scsi_done(). Otherwise all
the above actions would trigger a use-after-free. Hence remove the
scsi_done() call from srp_abort(). Keep the srp_free_req() call
before returning SUCCESS because we may not see the command again if
SUCCESS is returned.

Cc: Bob Pearson <rpearsonhpe@gmail.com>
Cc: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: d8536670916a ("IB/srp: Avoid having aborted requests hang")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230823205727.505681-1-bvanassche@acm.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/uverbs: Fix typo of sizeof argument

commit c489800e0d48097fc6afebd862c6afa039110a36 upstream.

Since size of 'hdr' pointer and '*hdr' structure is equal on 64-bit
machines issue probably didn't cause any wrong behavior. But anyway,
fixing of typo is required.

Fixes: da0f60df7bd5 ("RDMA/uverbs: Prohibit write() calls with too small buffers")
Co-developed-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com>
Signed-off-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com>
Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Link: https://lore.kernel.org/r/20230905103258.1738246-1-konstantin.meskhidze@huawei.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/cma: Fix truncation compilation warning in make_cma_ports

commit 18126c767658ae8a831257c6cb7776c5ba5e7249 upstream.

The following compilation error is false alarm as RDMA devices don't
have such large amount of ports to actually cause to format truncation.

drivers/infiniband/core/cma_configfs.c: In function ‘make_cma_ports’:
drivers/infiniband/core/cma_configfs.c:223:57: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
  223 |                 snprintf(port_str, sizeof(port_str), "%u", i + 1);
      |                                                         ^
drivers/infiniband/core/cma_configfs.c:223:17: note: ‘snprintf’ output between 2 and 11 bytes into a destination of size 10
  223 |                 snprintf(port_str, sizeof(port_str), "%u", i + 1);
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[5]: *** [scripts/Makefile.build:243: drivers/infiniband/core/cma_configfs.o] Error 1

Fixes: 045959db65c6 ("IB/cma: Add configfs for rdma_cm")
Link: https://lore.kernel.org/r/a7e3b347ee134167fa6a3787c56ef231a04bc8c2.1694434639.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/cma: Initialize ib_sa_multicast structure to 0 when join

commit e0fe97efdb00f0f32b038a4836406a82886aec9c upstream.

Initialize the structure to 0 so that it's fields won't have random
values. For example fields like rec.traffic_class (as well as
rec.flow_label and rec.sl) is used to generate the user AH through:
  cma_iboe_join_multicast
    cma_make_mc_event
      ib_init_ah_from_mcmember

And a random traffic_class causes a random IP DSCP in RoCEv2.

Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/20230927090511.603595-1-markzhang@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: pxa: disable pinctrl calls for MMP_GPIO

commit f0575116507b981e6a810e78ce3c9040395b958b upstream.

Similarly to PXA3xx and MMP2, pinctrl-single isn't capable of setting
pin direction on MMP either.

Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request")
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpio: aspeed: fix the GPIO number passed to pinctrl_gpio_set_config()

commit f9315f17bf778cb8079a29639419fcc8a41a3c84 upstream.

pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.

Fixes: 5ae4cb94b313 ("gpio: aspeed: Add debounce support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix the size of a buffer in add_port_entries()

commit d7f393430a17c2bfcdf805462a5aa80be4285b27 upstream.

In order to be sure that 'buff' is never truncated, its size should be
12, not 11.

When building with W=1, this fixes the following warnings:

  drivers/infiniband/hw/mlx4/sysfs.c: In function ‘add_port_entries’:
  drivers/infiniband/hw/mlx4/sysfs.c:268:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
    268 |                 sprintf(buff, "%d", i);
        |                                  ^
  drivers/infiniband/hw/mlx4/sysfs.c:268:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
    268 |                 sprintf(buff, "%d", i);
        |                 ^~~~~~~~~~~~~~~~~~~~~~
  drivers/infiniband/hw/mlx4/sysfs.c:286:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
    286 |                 sprintf(buff, "%d", i);
        |                                  ^
  drivers/infiniband/hw/mlx4/sysfs.c:286:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
    286 |                 sprintf(buff, "%d", i);
        |                 ^~~~~~~~~~~~~~~~~~~~~~

Fixes: c1e7e466120b ("IB/mlx4: Add iov directory in sysfs under the ib device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0bb1443eb47308bc9be30232cc23004c4d4cf43e.1695448530.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

of: dynamic: Fix potential memory leak in of_changeset_action()

commit 55e95bfccf6db8d26a66c46e1de50d53c59a6774 upstream.

Smatch complains that the error path where "action" is invalid leaks
the "ce" allocation:
    drivers/of/dynamic.c:935 of_changeset_action()
    warn: possible memory leak of 'ce'

Fix this by doing the validation before the allocation.

Note that there is not any actual problem with upstream kernels. All
callers of of_changeset_action() are static inlines with fixed action
values.

Fixes: 914d9d831e61 ("of: dynamic: Refactor action prints to not use "%pOF" inside devtree_lock")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202309011059.EOdr4im9-lkp@intel.com/
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7dfaf999-30ad-491c-9615-fb1138db121c@moroto.mountain
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/core: Require admin capabilities to set system parameters

commit c38d23a54445f9a8aa6831fafc9af0496ba02f9e upstream.

Like any other set command, require admin permissions to do it.

Cc: stable@vger.kernel.org
Fixes: 2b34c5580226 ("RDMA/core: Add command to set ib_core device net namspace sharing mode")
Link: https://lore.kernel.org/r/75d329fdd7381b52cbdf87910bef16c9965abb1f.1696443438.git.leon@kernel.org
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm zoned: free dmz->ddev array in dmz_put_zoned_devices

commit 9850ccd5dd88075b2b7fd28d96299d5535f58cc5 upstream.

Commit 4dba12881f88 ("dm zoned: support arbitrary number of devices")
made the pointers to additional zoned devices to be stored in a
dynamically allocated dmz->ddev array. However, this array is not freed.

Rename dmz_put_zoned_device to dmz_put_zoned_devices and fix it to
free the dmz->ddev array when cleaning up zoned device information.
Remove NULL assignment for all dmz->ddev elements and just free the
dmz->ddev array instead.

Found by Linux Verification Center (linuxtesting.org).

Fixes: 4dba12881f88 ("dm zoned: support arbitrary number of devices")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Fix crash with nr_cpus=1 option

commit d3b3c637e4eb8d3bbe53e5692aee66add72f9851 upstream.

John David Anglin reported that giving "nr_cpus=1" on the command
line causes a crash, while "maxcpus=1" works.

Reported-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smb: use kernel_connect() and kernel_bind()

commit cedc019b9f260facfadd20c6c490e403abf292e3 upstream.

Recent changes to kernel_connect() and kernel_bind() ensure that
callers are insulated from changes to the address parameter made by BPF
SOCK_ADDR hooks. This patch wraps direct calls to ops->connect() and
ops->bind() with kernel_connect() and kernel_bind() to ensure that SMB
mounts do not see their mount address overwritten in such cases.

Link: https://lore.kernel.org/netdev/9944248dba1bce861375fcce9de663934d933ba9.camel@redhat.com/
Cc: <stable@vger.kernel.org> # 6.0+
Signed-off-by: Jordan Rife <jrife@google.com>
Acked-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

intel_idle: add Emerald Rapids Xeon support

[ Upstream commit 74528edfbc664f9d2c927c4e5a44f1285598ed0f ]

Emerald Rapids (EMR) is the next Intel Xeon processor after Sapphire
Rapids (SPR).

EMR C-states are the same as SPR C-states, and we expect that EMR
C-state characteristics (latency and target residency) will be the
same as in SPR. Therefore, add EMR support by using SPR C-states table.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: intel-ish-hid: ipc: Disable and reenable ACPI GPE bit

[ Upstream commit 8f02139ad9a7e6e5c05712f8c1501eebed8eacfd ]

The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
service, which allows to wakup device when the system is in S5 (Soft-Off
state). This OOB service can be enabled/disabled from BIOS settings. When
enabled, the ISH device gets PME wake capability. To enable PME wakeup,
driver also needs to enable ACPI GPE bit.

On resume, BIOS will clear the wakeup bit. So driver need to re-enable it
in resume function to keep the next wakeup capability. But this BIOS
clearing of wakeup bit doesn't decrement internal OS GPE reference count,
so this reenabling on every resume will cause reference count to overflow.

So first disable and reenable ACPI GPE bit using acpi_disable_gpe().

Fixes: 2e23a70edabe ("HID: intel-ish-hid: ipc: finish power flow for EHL OOB")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://lore.kernel.org/lkml/CAAd53p4=oLYiH2YbVSmrPNj1zpMcfp=Wxbasb5vhMXOWCArLCg@mail.gmail.com/T/
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: sony: remove duplicate NULL check before calling usb_free_urb()

[ Upstream commit b328dd02e19cb9d3b35de4322f5363516a20ac8c ]

usb_free_urb() does the NULL check itself, so there is no need to duplicate
it prior to calling.

Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1cd4004cde7c9 ("HID: sony: Fix a potential memory leak in sony_probe()")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netlink: annotate data-races around sk->sk_err

[ Upstream commit d0f95894fda7d4f895b29c1097f92d7fee278cb2 ]

syzbot caught another data-race in netlink when
setting sk->sk_err.

Annotate all of them for good measure.

BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg

write to 0xffff8881613bb220 of 4 bytes by task 28147 on cpu 0:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

write to 0xffff8881613bb220 of 4 bytes by task 28146 on cpu 1:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x00000000 -> 0x00000016

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 28146 Comm: syz-executor.0 Not tainted 6.6.0-rc3-syzkaller-00055-g9ed22ae6be81 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/06/2023

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231003183455.3410550-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netlink: Fix potential skb memleak in netlink_ack

[ Upstream commit e69761483361f3df455bc493c99af0ef1744a14f ]

Fix coverity issue 'Resource leak'.

We should clean the skb resource if nlmsg_put/append failed.

Fixes: 738136a0e375 ("netlink: split up copies in the ack construction")
Signed-off-by: Tao Chen <chentao.kernel@linux.alibaba.com>
Link: https://lore.kernel.org/r/bff442d62c87de6299817fe1897cc5a5694ba9cc.1667638204.git.chentao.kernel@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: d0f95894fda7 ("netlink: annotate data-races around sk->sk_err")
Signed-off-by: Sasha Levin <sashal@kernel.org>

netlink: split up copies in the ack construction

[ Upstream commit 738136a0e3757a8534df3ad97d6ff6d7f429f6c1 ]

Clean up the use of unsafe_memcpy() by adding a flexible array
at the end of netlink message header and splitting up the header
and data copies.

Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d0f95894fda7 ("netlink: annotate data-races around sk->sk_err")
Signed-off-by: Sasha Levin <sashal@kernel.org>

sctp: update hb timer immediately after users change hb_interval

[ Upstream commit 1f4e803cd9c9166eb8b6c8b0b8e4124f7499fc07 ]

Currently, when hb_interval is changed by users, it won't take effect
until the next expiry of hb timer. As the default value is 30s, users
have to wait up to 30s to wait its hb_interval update to work.

This becomes pretty bad in containers where a much smaller value is
usually set on hb_interval. This patch improves it by resetting the
hb timer immediately once the value of hb_interval is updated by users.

Note that we don't address the already existing 'problem' when sending
a heartbeat 'on demand' if one hb has just been sent(from the timer)
mentioned in:

  https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg590224.html

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/75465785f8ee5df2fb3acdca9b8fafdc18984098.1696172660.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sctp: update transport state when processing a dupcook packet

[ Upstream commit 2222a78075f0c19ca18db53fd6623afb4aff602d ]

During the 4-way handshake, the transport's state is set to ACTIVE in
sctp_process_init() when processing INIT_ACK chunk on client or
COOKIE_ECHO chunk on server.

In the collision scenario below:

  192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
    192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
    192.168.1.2 > 192.168.1.1: sctp (1) [INIT ACK] [init tag: 3922216408]
    192.168.1.1 > 192.168.1.2: sctp (1) [COOKIE ECHO]
    192.168.1.2 > 192.168.1.1: sctp (1) [COOKIE ACK]
  192.168.1.1 > 192.168.1.2: sctp (1) [INIT ACK] [init tag: 3914796021]

when processing COOKIE_ECHO on 192.168.1.2, as it's in COOKIE_WAIT state,
sctp_sf_do_dupcook_b() is called by sctp_sf_do_5_2_4_dupcook() where it
creates a new association and sets its transport to ACTIVE then updates
to the old association in sctp_assoc_update().

However, in sctp_assoc_update(), it will skip the transport update if it
finds a transport with the same ipaddr already existing in the old asoc,
and this causes the old asoc's transport state not to move to ACTIVE
after the handshake.

This means if DATA retransmission happens at this moment, it won't be able
to enter PF state because of the check 'transport->state == SCTP_ACTIVE'
in sctp_do_8_2_transport_strike().

This patch fixes it by updating the transport in sctp_assoc_update() with
sctp_assoc_add_peer() where it updates the transport state if there is
already a transport with the same ipaddr exists in the old asoc.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/fd17356abe49713ded425250cc1ae51e9f5846c6.1696172325.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: fix delayed ACKs for MSS boundary condition

[ Upstream commit 4720852ed9afb1c5ab84e96135cb5b73d5afde6f ]

This commit fixes poor delayed ACK behavior that can cause poor TCP
latency in a particular boundary condition: when an application makes
a TCP socket write that is an exact multiple of the MSS size.

The problem is that there is painful boundary discontinuity in the
current delayed ACK behavior. With the current delayed ACK behavior,
we have:

(1) If an app reads data when > 1*MSS is unacknowledged, then
    tcp_cleanup_rbuf() ACKs immediately because of:

     tp->rcv_nxt - tp->rcv_wup > icsk->icsk_ack.rcv_mss ||

(2) If an app reads all received data, and the packets were < 1*MSS,
    and either (a) the app is not ping-pong or (b) we received two
    packets < 1*MSS, then tcp_cleanup_rbuf() ACKs immediately beecause
    of:

     ((icsk->icsk_ack.pending & ICSK_ACK_PUSHED2) ||
      ((icsk->icsk_ack.pending & ICSK_ACK_PUSHED) &&
       !inet_csk_in_pingpong_mode(sk))) &&

(3) *However*: if an app reads exactly 1*MSS of data,
    tcp_cleanup_rbuf() does not send an immediate ACK. This is true
    even if the app is not ping-pong and the 1*MSS of data had the PSH
    bit set, suggesting the sending application completed an
    application write.

Thus if the app is not ping-pong, we have this painful case where
>1*MSS gets an immediate ACK, and <1*MSS gets an immediate ACK, but a
write whose last skb is an exact multiple of 1*MSS can get a 40ms
delayed ACK. This means that any app that transfers data in one
direction and takes care to align write size or packet size with MSS
can suffer this problem. With receive zero copy making 4KB MSS values
more common, it is becoming more common to have application writes
naturally align with MSS, and more applications are likely to
encounter this delayed ACK problem.

The fix in this commit is to refine the delayed ACK heuristics with a
simple check: immediately ACK a received 1*MSS skb with PSH bit set if
the app reads all data. Why? If an skb has a len of exactly 1*MSS and
has the PSH bit set then it is likely the end of an application
write. So more data may not be arriving soon, and yet the data sender
may be waiting for an ACK if cwnd-bound or using TX zero copy. Thus we
set ICSK_ACK_PUSHED in this case so that tcp_cleanup_rbuf() will send
an ACK immediately if the app reads all of the data and is not
ping-pong. Note that this logic is also executed for the case where
len > MSS, but in that case this logic does not matter (and does not
hurt) because tcp_cleanup_rbuf() will always ACK immediately if the
app reads data and there is more than an MSS of unACKed data.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Xin Guo <guoxin0309@gmail.com>
Link: https://lore.kernel.org/r/20231001151239.1866845-2-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: fix quick-ack counting to count actual ACKs of new data

[ Upstream commit 059217c18be6757b95bfd77ba53fb50b48b8a816 ]

This commit fixes quick-ack counting so that it only considers that a
quick-ack has been provided if we are sending an ACK that newly
acknowledges data.

The code was erroneously using the number of data segments in outgoing
skbs when deciding how many quick-ack credits to remove. This logic
does not make sense, and could cause poor performance in
request-response workloads, like RPC traffic, where requests or
responses can be multi-segment skbs.

When a TCP connection decides to send N quick-acks, that is to
accelerate the cwnd growth of the congestion control module
controlling the remote endpoint of the TCP connection. That quick-ack
decision is purely about the incoming data and outgoing ACKs. It has
nothing to do with the outgoing data or the size of outgoing data.

And in particular, an ACK only serves the intended purpose of allowing
the remote congestion control to grow the congestion window quickly if
the ACK is ACKing or SACKing new data.

The fix is simple: only count packets as serving the goal of the
quickack mechanism if they are ACKing/SACKing new data. We can tell
whether this is the case by checking inet_csk_ack_scheduled(), since
we schedule an ACK exactly when we are ACKing/SACKing new data.

Fixes: fc6415bcb0f5 ("[TCP]: Fix quick-ack decrementing with TSO.")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231001151239.1866845-1-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tipc: fix a potential deadlock on &tx->lock

[ Upstream commit 08e50cf071847323414df0835109b6f3560d44f5 ]

It seems that tipc_crypto_key_revoke() could be be invoked by
wokequeue tipc_crypto_work_rx() under process context and
timer/rx callback under softirq context, thus the lock acquisition
on &tx->lock seems better use spin_lock_bh() to prevent possible
deadlock.

This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.

tipc_crypto_work_rx() <workqueue>
--> tipc_crypto_key_distr()
--> tipc_bcast_xmit()
--> tipc_bcbase_xmit()
--> tipc_bearer_bc_xmit()
--> tipc_crypto_xmit()
--> tipc_ehdr_build()
--> tipc_crypto_key_revoke()
--> spin_lock(&tx->lock)
<timer interrupt>
   --> tipc_disc_timeout()
   --> tipc_bearer_xmit_skb()
   --> tipc_crypto_xmit()
   --> tipc_ehdr_build()
   --> tipc_crypto_key_revoke()
   --> spin_lock(&tx->lock) <deadlock here>

Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication")
Link: https://lore.kernel.org/r/20230927181414.59928-1-dg573847474@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: dwmac-stm32: fix resume on STM32 MCU

[ Upstream commit 6f195d6b0da3b689922ba9e302af2f49592fa9fc ]

The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.

This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.

This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.

Fixes: 6528e02cc9ff ("net: ethernet: stmmac: add adaptation for stm32mp157c.")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv4: Set offload_failed flag in fibmatch results

[ Upstream commit 0add5c597f3253a9c6108a0a81d57f44ab0d9d30 ]

Due to a small omission, the offload_failed flag is missing from ipv4
fibmatch results. Make sure it is set correctly.

The issue can be witnessed using the following commands:
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add dummy1 up type dummy
ip route add 192.0.2.0/24 dev dummy1
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/fib/fail_route_offload
ip route add 198.51.100.0/24 dev dummy1
ip route
# 192.168.15.0/24 has rt_trap
# 198.51.100.0/24 has rt_offload_failed
ip route get 192.168.15.1 fibmatch
# Result has rt_trap
ip route get 198.51.100.1 fibmatch
# Result differs from the route shown by `ip route`, it is missing
# rt_offload_failed
ip link del dev dummy1
echo 1 > /sys/bus/netdevsim/del_device

Fixes: 36c5100e859d ("IPv4: Add "offload failed" indication to routes")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230926182730.231208-1-bpoirier@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure

[ Upstream commit 087388278e0f301f4c61ddffb1911d3a180f84b8 ]

nft_rbtree_gc_elem() walks back and removes the end interval element that
comes before the expired element.

There is a small chance that we've cached this element as 'rbe_ge'.
If this happens, we hold and test a pointer that has been queued for
freeing.

It also causes spurious insertion failures:

$ cat test-testcases-sets-0044interval_overlap_0.1/testout.log
Error: Could not process rule: File exists
add element t s {  0 -  2 }
                   ^^^^^^
Failed to insert  0 -  2 given:
table ip t {
        set s {
                type inet_service
                flags interval,timeout
                timeout 2s
                gc-interval 2s
        }
}

The set (rbtree) is empty. The 'failure' doesn't happen on next attempt.

Reason is that when we try to insert, the tree may hold an expired
element that collides with the range we're adding.
While we do evict/erase this element, we can trip over this check:

if (rbe_ge && nft_rbtree_interval_end(rbe_ge) && nft_rbtree_interval_end(new))
      return -ENOTEMPTY;

rbe_ge was erased by the synchronous gc, we should not have done this
check.  Next attempt won't find it, so retry results in successful
insertion.

Restart in-kernel to avoid such spurious errors.

Such restart are rare, unless userspace intentionally adds very large
numbers of elements with very short timeouts while setting a huge
gc interval.

Even in this case, this cannot loop forever, on each retry an existing
element has been removed.

As the caller is holding the transaction mutex, its impossible
for a second entity to add more expiring elements to the tree.

After this it also becomes feasible to remove the async gc worker
and perform all garbage collection from the commit path.

Fixes: c9e6978e2725 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: Deduplicate nft_register_obj audit logs

[ Upstream commit 0d880dc6f032e0b541520e9926f398a77d3d433c ]

When adding/updating an object, the transaction handler emits suitable
audit log entries already, the one in nft_obj_notify() is redundant. To
fix that (and retain the audit logging from objects' 'update' callback),
Introduce an "audit log free" variant for internal use.

Fixes: c520292f29b8 ("audit: log nftables configuration change events once per table")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com> (Audit)
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: netfilter: Extend nft_audit.sh

[ Upstream commit 203bb9d39866d3c5a8135433ce3742fe4f9d5741 ]

Add tests for sets and elements and deletion of all kinds. Also
reorder rule reset tests: By moving the bulk rule add command up, the
two 'reset rules' tests become identical.

While at it, fix for a failing bulk rule add test's error status getting
lost due to its use in a pipe. Avoid this by using a temporary file.

Headings in diff output for failing tests contain no useful data, strip
them.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
Stable-dep-of: 0d880dc6f032 ("netfilter: nf_tables: Deduplicate nft_register_obj audit logs")
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: netfilter: Test nf_tables audit logging

[ Upstream commit e8dbde59ca3fe925d0105bfb380e8429928b16dd ]

Compare NETFILTER_CFG type audit logs emitted from kernel upon ruleset
modifications against expected output.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 0d880dc6f032 ("netfilter: nf_tables: Deduplicate nft_register_obj audit logs")
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: handle the connecting collision properly in nf_conntrack_proto_sctp

[ Upstream commit 8e56b063c86569e51eed1c5681ce6361fa97fc7a ]

In Scenario A and B below, as the delayed INIT_ACK always changes the peer
vtag, SCTP ct with the incorrect vtag may cause packet loss.

Scenario A: INIT_ACK is delayed until the peer receives its own INIT_ACK

  192.168.1.2 > 192.168.1.1: [INIT] [init tag: 1328086772]
    192.168.1.1 > 192.168.1.2: [INIT] [init tag: 1414468151]
    192.168.1.2 > 192.168.1.1: [INIT ACK] [init tag: 1328086772]
  192.168.1.1 > 192.168.1.2: [INIT ACK] [init tag: 1650211246] *
  192.168.1.2 > 192.168.1.1: [COOKIE ECHO]
    192.168.1.1 > 192.168.1.2: [COOKIE ECHO]
    192.168.1.2 > 192.168.1.1: [COOKIE ACK]

Scenario B: INIT_ACK is delayed until the peer completes its own handshake

  192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
    192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
    192.168.1.2 > 192.168.1.1: sctp (1) [INIT ACK] [init tag: 3922216408]
    192.168.1.1 > 192.168.1.2: sctp (1) [COOKIE ECHO]
    192.168.1.2 > 192.168.1.1: sctp (1) [COOKIE ACK]
  192.168.1.1 > 192.168.1.2: sctp (1) [INIT ACK] [init tag: 3914796021] *

This patch fixes it as below:

In SCTP_CID_INIT processing:
- clear ct->proto.sctp.init[!dir] if ct->proto.sctp.init[dir] &&
  ct->proto.sctp.init[!dir]. (Scenario E)
- set ct->proto.sctp.init[dir].

In SCTP_CID_INIT_ACK processing:
- drop it if !ct->proto.sctp.init[!dir] && ct->proto.sctp.vtag[!dir] &&
  ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario B, Scenario C)
- drop it if ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
  ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario A)

In SCTP_CID_COOKIE_ACK processing:
- clear ct->proto.sctp.init[dir] and ct->proto.sctp.init[!dir].
  (Scenario D)

Also, it's important to allow the ct state to move forward with cookie_echo
and cookie_ack from the opposite dir for the collision scenarios.

There are also other Scenarios where it should allow the packet through,
addressed by the processing above:

Scenario C: new CT is created by INIT_ACK.

Scenario D: start INIT on the existing ESTABLISHED ct.

Scenario E: start INIT after the old collision on the existing ESTABLISHED
ct.

  192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
  192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
  (both side are stopped, then start new connection again in hours)
  192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 242308742]

Fixes: 9fb9cbb1082d ("[NETFILTER]: Add nf_conntrack subsystem.")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ibmveth: Remove condition to recompute TCP header checksum.

[ Upstream commit 51e7a66666e0ca9642c59464ef8359f0ac604d41 ]

In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.

Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).

Fixes: 7525de2516fb ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ethernet: ti: am65-cpsw: Fix error code in am65_cpsw_nuss_init_tx_chns()

[ Upstream commit 37d4f55567982e445f86dc0ff4ecfa72921abfe8 ]

This accidentally returns success, but it should return a negative error
code.

Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>