serdev: ttyport: restore client ops on deregistration

commit 0c5aae59270fb1f827acce182786094c9ccf598e upstream.

The serdev tty-port controller driver should reset the tty-port client
operations also on deregistration to avoid a NULL-pointer dereference in
case the port is later re-registered as a normal tty device.

Note that this can only happen with tty drivers such as 8250 which have
statically allocated port structures that can end up being reused and
where a later registration would not register a serdev controller (e.g.
due to registration errors or if the devicetree has been changed in
between).

Specifically, this can be an issue for any statically defined ports that
would be registered by 8250 core when an 8250 driver is being unbound.

Fixes: bed35c6dfa6a ("serdev: add a tty port controller driver")
Cc: stable <stable@vger.kernel.org> # 4.11
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200210145730.22762-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: qcom_geni_serial: Fix RX cancel command failure

commit 679aac5ead2f18d223554a52b543e1195e181811 upstream.

RX cancel command fails when BT is switched on and off multiple times.

To handle this, poll for the cancel bit in SE_GENI_S_IRQ_STATUS register
instead of SE_GENI_S_CMD_CTRL_REG.

As per the HPG update, handle the RX last bit after cancel command
and flush out the RX FIFO buffer.

Signed-off-by: satya priya <skakit@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1581415982-8793-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: imx: setup the correct sg entry for tx dma

commit f76707831829530ffdd3888bebc108aecefccaa0 upstream.

There has oops as below happen on i.MX8MP EVK platform that has
6G bytes DDR memory.

when (xmit->tail < xmit->head) && (xmit->head == 0),
it setups one sg entry with sg->length is zero:
sg_set_buf(sgl + 1, xmit->buf, xmit->head);

if xmit->buf is allocated from >4G address space, and SDMA only
support <4G address space, then dma_map_sg() will call swiotlb_map()
to do bounce buffer copying and mapping.

But swiotlb_map() don't allow sg entry's length is zero, otherwise
report BUG_ON().

So the patch is to correct the tx DMA scatter list.

Oops:
[  287.675715] kernel BUG at kernel/dma/swiotlb.c:497!
[  287.680592] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[  287.686075] Modules linked in:
[  287.689133] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.3-00016-g3fdc4e0-dirty #10
[  287.696872] Hardware name: FSL i.MX8MP EVK (DT)
[  287.701402] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[  287.706199] pc : swiotlb_tbl_map_single+0x1fc/0x310
[  287.711076] lr : swiotlb_map+0x60/0x148
[  287.714909] sp : ffff800010003c00
[  287.718221] x29: ffff800010003c00 x28: 0000000000000000
[  287.723533] x27: 0000000000000040 x26: ffff800011ae0000
[  287.728844] x25: ffff800011ae09f8 x24: 0000000000000000
[  287.734155] x23: 00000001b7af9000 x22: 0000000000000000
[  287.739465] x21: ffff000176409c10 x20: 00000000001f7ffe
[  287.744776] x19: ffff000176409c10 x18: 000000000000002e
[  287.750087] x17: 0000000000000000 x16: 0000000000000000
[  287.755397] x15: 0000000000000000 x14: 0000000000000000
[  287.760707] x13: ffff00017f334000 x12: 0000000000000001
[  287.766018] x11: 00000000001fffff x10: 0000000000000000
[  287.771328] x9 : 0000000000000003 x8 : 0000000000000000
[  287.776638] x7 : 0000000000000000 x6 : 0000000000000000
[  287.781949] x5 : 0000000000200000 x4 : 0000000000000000
[  287.787259] x3 : 0000000000000001 x2 : 00000001b7af9000
[  287.792570] x1 : 00000000fbfff000 x0 : 0000000000000000
[  287.797881] Call trace:
[  287.800328]  swiotlb_tbl_map_single+0x1fc/0x310
[  287.804859]  swiotlb_map+0x60/0x148
[  287.808347]  dma_direct_map_page+0xf0/0x130
[  287.812530]  dma_direct_map_sg+0x78/0xe0
[  287.816453]  imx_uart_dma_tx+0x134/0x2f8
[  287.820374]  imx_uart_dma_tx_callback+0xd8/0x168
[  287.824992]  vchan_complete+0x194/0x200
[  287.828828]  tasklet_action_common.isra.0+0x154/0x1a0
[  287.833879]  tasklet_action+0x24/0x30
[  287.837540]  __do_softirq+0x120/0x23c
[  287.841202]  irq_exit+0xb8/0xd8
[  287.844343]  __handle_domain_irq+0x64/0xb8
[  287.848438]  gic_handle_irq+0x5c/0x148
[  287.852185]  el1_irq+0xb8/0x180
[  287.855327]  cpuidle_enter_state+0x84/0x360
[  287.859508]  cpuidle_enter+0x34/0x48
[  287.863083]  call_cpuidle+0x18/0x38
[  287.866571]  do_idle+0x1e0/0x280
[  287.869798]  cpu_startup_entry+0x20/0x40
[  287.873721]  rest_init+0xd4/0xe0
[  287.876949]  arch_call_rest_init+0xc/0x14
[  287.880958]  start_kernel+0x420/0x44c
[  287.884622] Code: 9124c021 9417aff8 a94363f7 17ffffd5 (d4210000)
[  287.890718] ---[ end trace 5bc44c4ab6b009ce ]---
[  287.895334] Kernel panic - not syncing: Fatal exception in interrupt
[  287.901686] SMP: stopping secondary CPUs
[  288.905607] SMP: failed to stop secondary CPUs 0-1
[  288.910395] Kernel Offset: disabled
[  288.913882] CPU features: 0x0002,2000200c
[  288.917888] Memory Limit: none
[  288.920944] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

Reported-by: Eagle Zhou <eagle.zhou@nxp.com>
Tested-by: Eagle Zhou <eagle.zhou@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 7942f8577f2a ("serial: imx: TX DMA: clean up sg initialization")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/1581401761-6378-1-git-send-email-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/serial: atmel: manage shutdown in case of RS485 or ISO7816 mode

commit 04b5bfe3dc94e64d0590c54045815cb5183fb095 upstream.

In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions.
Prevent the rx restart that is implemented in RS485 or ISO7816 modes when
calling atmel_stop_tx() by using the atomic information tasklet_shutdown
that is already in place for this purpose.

Fixes: 98f2082c3ac4 ("tty/serial: atmel: enforce tasklet init and termination sequences")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: Check UPF_IRQ_SHARED in advance

commit 7febbcbc48fc92e3f33863b32ed715ba4aff18c4 upstream.

The commit 54e53b2e8081
  ("tty: serial: 8250: pass IRQ shared flag to UART ports")
nicely explained the problem:

---8<---8<---

On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.

This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling routines himself.

Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.

Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.

Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system:

|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85

---8<---8<---

But unfortunately didn't fix the root cause. Let's try again here by moving
IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup().

This should fix the similar issue reported for 8250_pnp case.

Since this change we don't need to have custom solutions in 8250_aspeed_vuart
and 8250_of drivers, thus, drop them.

Fixes: 1c2f04937b3e ("serial: 8250: add IRQ trigger support")
Reported-by: Li RongQing <lirongqing@baidu.com>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/cpu/amd: Enable the fixed Instructions Retired counter IRPERF

commit 21b5ee59ef18e27d85810584caf1f7ddc705ea83 upstream.

Commit

  aaf248848db50 ("perf/x86/msr: Add AMD IRPERF (Instructions Retired)
  performance counter")

added support for access to the free-running counter via 'perf -e
msr/irperf/', but when exercised, it always returns a 0 count:

BEFORE:

  $ perf stat -e instructions,msr/irperf/ true

   Performance counter stats for 'true':

             624,833      instructions
                   0      msr/irperf/

Simply set its enable bit - HWCR bit 30 - to make it start counting.

Enablement is restricted to all machines advertising IRPERF capability,
except those susceptible to an erratum that makes the IRPERF return
bad values.

That erratum occurs in Family 17h models 00-1fh [1], but not in F17h
models 20h and above [2].

AFTER (on a family 17h model 31h machine):

  $ perf stat -e instructions,msr/irperf/ true

   Performance counter stats for 'true':

             621,690      instructions
             622,490      msr/irperf/

[1] Revision Guide for AMD Family 17h Models 00h-0Fh Processors
[2] Revision Guide for AMD Family 17h Models 30h-3Fh Processors

The revision guides are available from the bugzilla Link below.

 [ bp: Massage commit message. ]

Fixes: aaf248848db50 ("perf/x86/msr: Add AMD IRPERF (Instructions Retired) performance counter")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Link: http://lkml.kernel.org/r/20200214201805.13830-1-kim.phillips@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mce/amd: Fix kobject lifetime

commit 51dede9c05df2b78acd6dcf6a17d21f0877d2d7b upstream.

Accessing the MCA thresholding controls in sysfs concurrently with CPU
hotplug can lead to a couple of KASAN-reported issues:

  BUG: KASAN: use-after-free in sysfs_file_ops+0x155/0x180
  Read of size 8 at addr ffff888367578940 by task grep/4019

and

  BUG: KASAN: use-after-free in show_error_count+0x15c/0x180
  Read of size 2 at addr ffff888368a05514 by task grep/4454

for example. Both result from the fact that the threshold block
creation/teardown code frees the descriptor memory itself instead of
defining proper ->release function and leaving it to the driver core to
take care of that, after all sysfs accesses have completed.

Do that and get rid of the custom freeing code, fixing the above UAFs in
the process.

  [ bp: write commit message. ]

Fixes: 95268664390b ("[PATCH] x86_64: mce_amd support for family 0x10 processors")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200214082801.13836-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/mce/amd: Publish the bank pointer only after setup has succeeded

commit 6e5cf31fbe651bed7ba1df768f2e123531132417 upstream.

threshold_create_bank() creates a bank descriptor per MCA error
thresholding counter which can be controlled over sysfs. It publishes
the pointer to that bank in a per-CPU variable and then goes on to
create additional thresholding blocks if the bank has such.

However, that creation of additional blocks in
allocate_threshold_blocks() can fail, leading to a use-after-free
through the per-CPU pointer.

Therefore, publish that pointer only after all blocks have been setup
successfully.

Fixes: 019f34fccfd5 ("x86, MCE, AMD: Move shared bank to node descriptor")
Reported-by: Saar Amar <Saar.Amar@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200128140846.phctkvx5btiexvbx@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/ima: use correct identifier for SetupMode variable

commit ff5ac61ee83c13f516544d29847d28be093a40ee upstream.

The IMA arch code attempts to inspect the "SetupMode" EFI variable
by populating a variable called efi_SetupMode_name with the string
"SecureBoot" and passing that to the EFI GetVariable service, which
obviously does not yield the expected result.

Given that the string is only referenced a single time, let's get
rid of the intermediate variable, and pass the correct string as
an immediate argument. While at it, do the same for "SecureBoot".

Fixes: 399574c64eaf ("x86/ima: retry detecting secure boot mode")
Fixes: 980ef4d22a95 ("x86/ima: check EFI SetupMode too")
Cc: Matthew Garrett <mjg59@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: stable@vger.kernel.org # v5.3
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

jbd2: fix ocfs2 corrupt when clearing block group bits

commit 8eedabfd66b68a4623beec0789eac54b8c9d0fb6 upstream.

I found a NULL pointer dereference in ocfs2_block_group_clear_bits().
The running environment:
kernel version: 4.19
A cluster with two nodes, 5 luns mounted on two nodes, and do some
file operations like dd/fallocate/truncate/rm on every lun with storage
network disconnection.

The fallocate operation on dm-23-45 caused an null pointer dereference.

The information of NULL pointer dereference as follows:
[577992.878282] JBD2: Error -5 detected when updating journal superblock for dm-23-45.
[577992.878290] Aborting journal on device dm-23-45.
...
[577992.890778] JBD2: Error -5 detected when updating journal superblock for dm-24-46.
[577992.890908] __journal_remove_journal_head: freeing b_committed_data
[577992.890916] (fallocate,88392,52):ocfs2_extend_trans:474 ERROR: status = -30
[577992.890918] __journal_remove_journal_head: freeing b_committed_data
[577992.890920] (fallocate,88392,52):ocfs2_rotate_tree_right:2500 ERROR: status = -30
[577992.890922] __journal_remove_journal_head: freeing b_committed_data
[577992.890924] (fallocate,88392,52):ocfs2_do_insert_extent:4382 ERROR: status = -30
[577992.890928] (fallocate,88392,52):ocfs2_insert_extent:4842 ERROR: status = -30
[577992.890928] __journal_remove_journal_head: freeing b_committed_data
[577992.890930] (fallocate,88392,52):ocfs2_add_clusters_in_btree:4947 ERROR: status = -30
[577992.890933] __journal_remove_journal_head: freeing b_committed_data
[577992.890939] __journal_remove_journal_head: freeing b_committed_data
[577992.890949] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
[577992.890950] Mem abort info:
[577992.890951]   ESR = 0x96000004
[577992.890952]   Exception class = DABT (current EL), IL = 32 bits
[577992.890952]   SET = 0, FnV = 0
[577992.890953]   EA = 0, S1PTW = 0
[577992.890954] Data abort info:
[577992.890955]   ISV = 0, ISS = 0x00000004
[577992.890956]   CM = 0, WnR = 0
[577992.890958] user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000f8da07a9
[577992.890960] [0000000000000020] pgd=0000000000000000
[577992.890964] Internal error: Oops: 96000004 [#1] SMP
[577992.890965] Process fallocate (pid: 88392, stack limit = 0x00000000013db2fd)
[577992.890968] CPU: 52 PID: 88392 Comm: fallocate Kdump: loaded Tainted: G        W  OE     4.19.36 #1
[577992.890969] Hardware name: Huawei TaiShan 2280 V2/BC82AMDD, BIOS 0.98 08/25/2019
[577992.890971] pstate: 60400009 (nZCv daif +PAN -UAO)
[577992.891054] pc : _ocfs2_free_suballoc_bits+0x63c/0x968 [ocfs2]
[577992.891082] lr : _ocfs2_free_suballoc_bits+0x618/0x968 [ocfs2]
[577992.891084] sp : ffff0000c8e2b810
[577992.891085] x29: ffff0000c8e2b820 x28: 0000000000000000
[577992.891087] x27: 00000000000006f3 x26: ffffa07957b02e70
[577992.891089] x25: ffff807c59d50000 x24: 00000000000006f2
[577992.891091] x23: 0000000000000001 x22: ffff807bd39abc30
[577992.891093] x21: ffff0000811d9000 x20: ffffa07535d6a000
[577992.891097] x19: ffff000001681638 x18: ffffffffffffffff
[577992.891098] x17: 0000000000000000 x16: ffff000080a03df0
[577992.891100] x15: ffff0000811d9708 x14: 203d207375746174
[577992.891101] x13: 73203a524f525245 x12: 20373439343a6565
[577992.891103] x11: 0000000000000038 x10: 0101010101010101
[577992.891106] x9 : ffffa07c68a85d70 x8 : 7f7f7f7f7f7f7f7f
[577992.891109] x7 : 0000000000000000 x6 : 0000000000000080
[577992.891110] x5 : 0000000000000000 x4 : 0000000000000002
[577992.891112] x3 : ffff000001713390 x2 : 2ff90f88b1c22f00
[577992.891114] x1 : ffff807bd39abc30 x0 : 0000000000000000
[577992.891116] Call trace:
[577992.891139]  _ocfs2_free_suballoc_bits+0x63c/0x968 [ocfs2]
[577992.891162]  _ocfs2_free_clusters+0x100/0x290 [ocfs2]
[577992.891185]  ocfs2_free_clusters+0x50/0x68 [ocfs2]
[577992.891206]  ocfs2_add_clusters_in_btree+0x198/0x5e0 [ocfs2]
[577992.891227]  ocfs2_add_inode_data+0x94/0xc8 [ocfs2]
[577992.891248]  ocfs2_extend_allocation+0x1bc/0x7a8 [ocfs2]
[577992.891269]  ocfs2_allocate_extents+0x14c/0x338 [ocfs2]
[577992.891290]  __ocfs2_change_file_space+0x3f8/0x610 [ocfs2]
[577992.891309]  ocfs2_fallocate+0xe4/0x128 [ocfs2]
[577992.891316]  vfs_fallocate+0x11c/0x250
[577992.891317]  ksys_fallocate+0x54/0x88
[577992.891319]  __arm64_sys_fallocate+0x28/0x38
[577992.891323]  el0_svc_common+0x78/0x130
[577992.891325]  el0_svc_handler+0x38/0x78
[577992.891327]  el0_svc+0x8/0xc

My analysis process as follows:
ocfs2_fallocate
  __ocfs2_change_file_space
    ocfs2_allocate_extents
      ocfs2_extend_allocation
        ocfs2_add_inode_data
          ocfs2_add_clusters_in_btree
            ocfs2_insert_extent
              ocfs2_do_insert_extent
                ocfs2_rotate_tree_right
                  ocfs2_extend_rotate_transaction
                    ocfs2_extend_trans
                      jbd2_journal_restart
                        jbd2__journal_restart
                          /* handle->h_transaction is NULL,
                           * is_handle_aborted(handle) is true
                           */
                          handle->h_transaction = NULL;
                          start_this_handle
                            return -EROFS;
            ocfs2_free_clusters
              _ocfs2_free_clusters
                _ocfs2_free_suballoc_bits
                  ocfs2_block_group_clear_bits
                    ocfs2_journal_access_gd
                      __ocfs2_journal_access
                        jbd2_journal_get_undo_access
                          /* I think jbd2_write_access_granted() will
                           * return true, because do_get_write_access()
                           * will return -EROFS.
                           */
                          if (jbd2_write_access_granted(...)) return 0;
                          do_get_write_access
                            /* handle->h_transaction is NULL, it will
                             * return -EROFS here, so do_get_write_access()
                             * was not called.
                             */
                            if (is_handle_aborted(handle)) return -EROFS;
                    /* bh2jh(group_bh) is NULL, caused NULL
                       pointer dereference */
                    undo_bg = (struct ocfs2_group_desc *)
                                bh2jh(group_bh)->b_committed_data;

If handle->h_transaction == NULL, then jbd2_write_access_granted()
does not really guarantee that journal_head will stay around,
not even speaking of its b_committed_data. The bh2jh(group_bh)
can be removed after ocfs2_journal_access_gd() and before call
"bh2jh(group_bh)->b_committed_data". So, we should move
is_handle_aborted() check from do_get_write_access() into
jbd2_journal_get_undo_access() and jbd2_journal_get_write_access()
before the call to jbd2_write_access_granted().

Link: https://lore.kernel.org/r/f72a623f-b3f1-381a-d91d-d22a1c83a336@huawei.com
Signed-off-by: Yan Wang <wangyan122@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jun Piao <piaojun@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: memory: Add missing brackets to untagged_addr() macro

commit d0022c0ef29b78bcbe8a5c5894bd2307143afce1 upstream.

Add brackets around the evaluation of the 'addr' parameter to the
untagged_addr() macro so that the cast to 'u64' applies to the result
of the expression.

Cc: <stable@vger.kernel.org>
Fixes: 597399d0cb91 ("arm64: tags: Preserve tags for addresses translated via TTBR1")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/hugetlb: Fix 8M hugepages on 8xx

commit 50a175dd18de7a647e72aca7daf4744e3a5a81e3 upstream.

With HW assistance all page tables must be 4k aligned, the 8xx drops
the last 12 bits during the walk.

Redefine HUGEPD_SHIFT_MASK to mask last 12 bits out. HUGEPD_SHIFT_MASK
is used to for alignment of page table cache.

Fixes: 22569b881d37 ("powerpc/8xx: Enable 8M hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/778b1a248c4c7ca79640eeff7740044da6a220a0.1581264115.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/hugetlb: Fix 512k hugepages on 8xx with 16k page size

commit f2b67ef90b0d5eca0f2255e02cf2f620bc0ddcdb upstream.

Commit 55c8fc3f4930 ("powerpc/8xx: reintroduce 16K pages with HW
assistance") redefined pte_t as a struct of 4 pte_basic_t, because
in 16K pages mode there are four identical entries in the
page table. But the size of hugepage tables is calculated based
of the size of (void *). Therefore, we end up with page tables
of size 1k instead of 4k for 512k pages.

As 512k hugepage tables are the same size as standard page tables,
ie 4k, use the standard page tables instead of PGT_CACHE tables.

Fixes: 3fb69c6a1a13 ("powerpc/8xx: Enable 512k hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/90ec56a2315be602494619ed0223bba3b0b8d619.1580997007.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/entry: Fix an #if which should be an #ifdef in entry_32.S

commit 9eb425b2e04e0e3006adffea5bf5f227a896f128 upstream.

Fixes: 12c3f1fd87bf ("powerpc/32s: get rid of CPU_FTR_601 feature")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/a99fc0ad65b87a1ba51cfa3e0e9034ee294c3e07.1582034961.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/tm: Fix clearing MSR[TS] in current when reclaiming on signal delivery

commit 2464cc4c345699adea52c7aef75707207cb8a2f6 upstream.

After a treclaim, we expect to be in non-transactional state. If we
don't clear the current thread's MSR[TS] before we get preempted, then
tm_recheckpoint_new_task() will recheckpoint and we get rescheduled in
suspended transaction state.

When handling a signal caught in transactional state,
handle_rt_signal64() calls get_tm_stackpointer() that treclaims the
transaction using tm_reclaim_current() but without clearing the
thread's MSR[TS]. This can cause the TM Bad Thing exception below if
later we pagefault and get preempted trying to access the user's
sigframe, using __put_user(). Afterwards, when we are rescheduled back
into do_page_fault() (but now in suspended state since the thread's
MSR[TS] was not cleared), upon executing 'rfid' after completion of
the page fault handling, the exception is raised because a transition
from suspended to non-transactional state is invalid.

  Unexpected TM Bad Thing exception at c00000000000de44 (msr 0x8000000302a03031) tm_scratch=800000010280b033
  Oops: Unrecoverable exception, sig: 6 [#1]
  LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
  CPU: 25 PID: 15547 Comm: a.out Not tainted 5.4.0-rc2 #32
  NIP:  c00000000000de44 LR: c000000000034728 CTR: 0000000000000000
  REGS: c00000003fe7bd70 TRAP: 0700   Not tainted  (5.4.0-rc2)
  MSR:  8000000302a03031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[SE]>  CR: 44000884  XER: 00000000
  CFAR: c00000000000dda4 IRQMASK: 0
  PACATMSCRATCH: 800000010280b033
  GPR00: c000000000034728 c000000f65a17c80 c000000001662800 00007fffacf3fd78
  GPR04: 0000000000001000 0000000000001000 0000000000000000 c000000f611f8af0
  GPR08: 0000000000000000 0000000078006001 0000000000000000 000c000000000000
  GPR12: c000000f611f84b0 c00000003ffcb200 0000000000000000 0000000000000000
  GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
  GPR20: 0000000000000000 0000000000000000 0000000000000000 c000000f611f8140
  GPR24: 0000000000000000 00007fffacf3fd68 c000000f65a17d90 c000000f611f7800
  GPR28: c000000f65a17e90 c000000f65a17e90 c000000001685e18 00007fffacf3f000
  NIP [c00000000000de44] fast_exception_return+0xf4/0x1b0
  LR [c000000000034728] handle_rt_signal64+0x78/0xc50
  Call Trace:
  [c000000f65a17c80] [c000000000034710] handle_rt_signal64+0x60/0xc50 (unreliable)
  [c000000f65a17d30] [c000000000023640] do_notify_resume+0x330/0x460
  [c000000f65a17e20] [c00000000000dcc4] ret_from_except_lite+0x70/0x74
  Instruction dump:
  7c4ff120 e8410170 7c5a03a6 38400000 f8410060 e8010070 e8410080 e8610088
  60000000 60000000 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed0989
  ---[ end trace 93094aa44b442f87 ]---

The simplified sequence of events that triggers the above exception is:

  ... # userspace in NON-TRANSACTIONAL state
  tbegin # userspace in TRANSACTIONAL state
  signal delivery # kernelspace in SUSPENDED state
  handle_rt_signal64()
    get_tm_stackpointer()
      treclaim # kernelspace in NON-TRANSACTIONAL state
    __put_user()
      page fault happens. We will never get back here because of the TM Bad Thing exception.

  page fault handling kicks in and we voluntarily preempt ourselves
  do_page_fault()
    __schedule()
      __switch_to(other_task)

  our task is rescheduled and we recheckpoint because the thread's MSR[TS] was not cleared
  __switch_to(our_task)
    switch_to_tm()
      tm_recheckpoint_new_task()
        trechkpt # kernelspace in SUSPENDED state

  The page fault handling resumes, but now we are in suspended transaction state
  do_page_fault()    completes
  rfid     <----- trying to get back where the page fault happened (we were non-transactional back then)
  TM Bad Thing # illegal transition from suspended to non-transactional

This patch fixes that issue by clearing the current thread's MSR[TS]
just after treclaim in get_tm_stackpointer() so that we stay in
non-transactional state in case we are preempted. In order to make
treclaim and clearing the thread's MSR[TS] atomic from a preemption
perspective when CONFIG_PREEMPT is set, preempt_disable/enable() is
used. It's also necessary to save the previous value of the thread's
MSR before get_tm_stackpointer() is called so that it can be exposed
to the signal handler later in setup_tm_sigcontexts() to inform the
userspace MSR at the moment of the signal delivery.

Found with tm-signal-context-force-tm kernel selftest.

Fixes: 2b0a576d15e0 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Gustavo Luiz Duarte <gustavold@linux.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200211033831.11165-1-gustavold@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/eeh: Fix deadlock handling dead PHB

commit d4f194ed9eb9841a8f978710e4d24296f791a85b upstream.

Recovering a dead PHB can currently cause a deadlock as the PCI
rescan/remove lock is taken twice.

This is caused as part of an existing bug in
eeh_handle_special_event(). The pe is processed while traversing the
PHBs even though the pe is unrelated to the loop. This causes the pe
to be, incorrectly, processed more than once.

Untangling this section can move the pe processing out of the loop and
also outside the locked section, correcting both problems.

Fixes: 2e25505147b8 ("powerpc/eeh: Fix crash when edev->pdev changes")
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Tested-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0547e82dbf90ee0729a2979a8cac5c91665c621f.1581051445.git.sbobroff@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/8xx: Fix clearing of bits 20-23 in ITLB miss

commit a4031afb9d10d97f4d0285844abbc0ab04245304 upstream.

In ITLB miss handled the line supposed to clear bits 20-23 on the L2
ITLB entry is buggy and does indeed nothing, leading to undefined
value which could allow execution when it shouldn't.

Properly do the clearing with the relevant instruction.

Fixes: 74fabcadfd43 ("powerpc/8xx: don't use r12/SPRN_SPRG_SCRATCH2 in TLB Miss handlers")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/4f70c2778163affce8508a210f65d140e84524b4.1581272050.git.christophe.leroy@c-s.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/panfrost: perfcnt: Reserve/use the AS attached to the perfcnt MMU context

commit dde2bb2da01e96c17f0a44b4a3cf72a30e66e3ef upstream.

We need to use the AS attached to the opened FD when dumping counters.

Reported-by: Antonio Caggiano <antonio.caggiano@collabora.com>
Fixes: 7282f7645d06 ("drm/panfrost: Implement per FD address spaces")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Tested-by: Antonio Caggiano <antonio.caggiano@collabora.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206141327.446127-1-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Fix potential overuse of kernel memory

commit 23954cb078febfc63a755301fe77e06bccdb4d2a upstream.

In routine wpa_supplicant_ioctl(), the user-controlled p->length is
checked to be at least the size of struct ieee_param size, but the code
does not detect the case where p->length is greater than the size
of the struct, thus a malicious user could be wasting kernel memory.
Fixes commit 554c0a3abf216 ("staging: Add rtl8723bs sdio wifi driver").

Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes: 554c0a3abf216 ("staging: Add rtl8723bs sdio wifi driver").
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-5-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8723bs: Fix potential security hole

commit ac33597c0c0d1d819dccfe001bcd0acef7107e7c upstream.

In routine rtw_hostapd_ioctl(), the user-controlled p->length is assumed
to be at least the size of struct ieee_param size, but this assumption is
never checked. This could result in out-of-bounds read/write on kernel
heap in case a p->length less than the size of struct ieee_param is
specified by the user. If p->length is allowed to be greater than the size
of the struct, then a malicious user could be wasting kernel memory.
Fixes commit 554c0a3abf216 ("0taging: Add rtl8723bs sdio wifi driver").

Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes 554c0a3abf216 ("0taging: Add rtl8723bs sdio wifi driver").
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-3-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Fix potential overuse of kernel memory

commit 4ddf8ab8d15ddbc52eefb44eb64e38466ce1f70f upstream.

In routine wpa_supplicant_ioctl(), the user-controlled p->length is
checked to be at least the size of struct ieee_param size, but the code
does not detect the case where p->length is greater than the size
of the struct, thus a malicious user could be wasting kernel memory.
Fixes commit a2c60d42d97c ("Add files for new driver - part 16").

Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes commit a2c60d42d97c ("Add files for new driver - part 16").
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-4-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Fix potential security hole

commit 499c405b2b80bb3a04425ba3541d20305e014d3e upstream.

In routine rtw_hostapd_ioctl(), the user-controlled p->length is assumed
to be at least the size of struct ieee_param size, but this assumption is
never checked. This could result in out-of-bounds read/write on kernel
heap in case a p->length less than the size of struct ieee_param is
specified by the user. If p->length is allowed to be greater than the size
of the struct, then a malicious user could be wasting kernel memory.
Fixes commit a2c60d42d97c ("Add files for new driver - part 16").

Reported by: Pietro Oliva <pietroliva@gmail.com>
Cc: Pietro Oliva <pietroliva@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Fixes: a2c60d42d97c ("staging: r8188eu: Add files for new driver - part 16")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20200210180235.21691-2-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: Revert "target/core: Inline transport_lun_remove_cmd()"

commit c14335ebb92a98646ddbf447e6cacc66de5269ad upstream.

Commit 83f85b8ec305 postponed the percpu_ref_put(&se_cmd->se_lun->lun_ref)
call from command completion to the time when the final command reference
is dropped. That approach is not compatible with the iSCSI target driver
because the iSCSI target driver keeps the command with the highest stat_sn
after it has completed until the next command is received (see also
iscsit_ack_from_expstatsn()). Fix this regression by reverting commit
83f85b8ec305.

Fixes: 83f85b8ec305 ("scsi: target/core: Inline transport_lun_remove_cmd()")
Cc: Pavel Zakharov <pavel.zakharov@delphix.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210051202.12934-1-bvanassche@acm.org
Reported-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: debug: fix string position formatting mixup with ret and len

commit b32196e35bd7bbc8038db1aba1fbf022dc469b6a upstream.

Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.

Addresses-Coverity: ("Unused value")
Fixes: 1381a5113caf ("usb: dwc3: debug: purge usage of strcat")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210095139.328711-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: Check for IOC/LST bit in TRB->ctrl fields

commit 5ee858975b13a9b40db00f456989a689fdbb296c upstream.

The current code in dwc3_gadget_ep_reclaim_completed_trb() will
check for IOC/LST bit in the event->status and returns if
IOC/LST bit is set. This logic doesn't work if multiple TRBs
are queued per request and the IOC/LST bit is set on the last
TRB of that request.

Consider an example where a queued request has multiple queued
TRBs and IOC/LST bit is set only for the last TRB. In this case,
the core generates XferComplete/XferInProgress events only for
the last TRB (since IOC/LST are set only for the last TRB). As
per the logic in dwc3_gadget_ep_reclaim_completed_trb()
event->status is checked for IOC/LST bit and returns on the
first TRB. This leaves the remaining TRBs left unhandled.

Similarly, if the gadget function enqueues an unaligned request
with sglist already in it, it should fail the same way, since we
will append another TRB to something that already uses more than
one TRB.

To aviod this, this patch changes the code to check for IOC/LST
bits in TRB->ctrl instead.

At a practical level, this patch resolves USB transfer stalls seen
with adb on dwc3 based HiKey960 after functionfs gadget added
scatter-gather support around v4.20.

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
[jstultz: forward ported to mainline, reworded commit log, reworked
 to only check trb->ctrl as suggested by Felipe]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: Fix SET/CLEAR_FEATURE and GET_STATUS flows

commit 9a0d6f7c0a83844baae1d6d85482863d2bf3b7a7 upstream.

SET/CLEAR_FEATURE for Remote Wakeup allowance not handled correctly.
GET_STATUS handling provided not correct data on DATA Stage.
Issue seen when gadget's dr_mode set to "otg" mode and connected
to MacOS.
Both are fixed and tested using USBCV Ch.9 tests.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Fixes: fa389a6d7726 ("usb: dwc2: gadget: Add remote_wakeup_allowed flag")
Tested-by: Jack Mitchell <ml@embed.me.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: hub: Fix the broken detection of USB3 device in SMSC hub

commit 1208f9e1d758c991b0a46a1bd60c616b906bbe27 upstream.

Renesas R-Car H3ULCB + Kingfisher Infotainment Board is either not able
to detect the USB3.0 mass storage devices or is detecting those as
USB2.0 high speed devices.

The explanation given by Renesas is that, due to a HW issue, the XHCI
driver does not wake up after going to sleep on connecting a USB3.0
device.

In order to mitigate that, disable the auto-suspend feature
specifically for SMSC hubs from hub_probe() function, as a quirk.

Renesas Kingfisher Infotainment Board has two USB3.0 ports (CN2) which
are connected via USB5534B 4-port SuperSpeed/Hi-Speed, low-power,
configurable hub controller.

[1] SanDisk USB 3.0 device detected as USB-2.0 before the patch
 [   74.036390] usb 5-1.1: new high-speed USB device number 4 using xhci-hcd
 [   74.061598] usb 5-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
 [   74.069976] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
 [   74.077303] usb 5-1.1: Product: Ultra
 [   74.080980] usb 5-1.1: Manufacturer: SanDisk
 [   74.085263] usb 5-1.1: SerialNumber: 4C530001110208116550

[2] SanDisk USB 3.0 device detected as USB-3.0 after the patch
 [   34.565078] usb 6-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
 [   34.588719] usb 6-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
 [   34.597098] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
 [   34.604430] usb 6-1.1: Product: Ultra
 [   34.608110] usb 6-1.1: Manufacturer: SanDisk
 [   34.612397] usb 6-1.1: SerialNumber: 4C530001110208116550

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1580989763-32291-1-git-send-email-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: hub: Don't record a connect-change event during reset-resume

commit 8099f58f1ecddf4f374f4828a3dff8397c7cbd74 upstream.

Paul Zimmerman reports that his USB Bluetooth adapter sometimes
crashes following system resume, when it receives a
Get-Device-Descriptor request while it is busy doing something else.

Such a request was added by commit a4f55d8b8c14 ("usb: hub: Check
device descriptor before resusciation").  It gets sent when the hub
driver's work thread checks whether a connect-change event on an
enabled port really indicates a new device has been connected, as
opposed to an old device momentarily disconnecting and then
reconnecting (which can happen with xHCI host controllers, since they
automatically enable connected ports).

The same kind of thing occurs when a port's power session is lost
during system suspend.  When the system wakes up it sees a
connect-change event on the port, and if the child device's
persist_enabled flag was set then hub_activate() sets the device's
reset_resume flag as well as the port's bit in hub->change_bits.  The
reset-resume code then takes responsibility for checking that the same
device is still attached to the port, and it does this as part of the
device's resume pathway.  By the time the hub driver's work thread
starts up again, the device has already been fully reinitialized and
is busy doing its own thing.  There's no need for the work thread to
do the same check a second time, and in fact this unnecessary check is
what caused the problem that Paul observed.

Note that performing the unnecessary check is not actually a bug.
Devices are supposed to be able to send descriptors back to the host
even when they are busy doing something else.  The underlying cause of
Paul's problem lies in his Bluetooth adapter.  Nevertheless, we
shouldn't perform the same check twice in a row -- and as a nice side
benefit, removing the extra check allows the Bluetooth adapter to work
more reliably.

The work thread performs its check when it sees that the port's bit is
set in hub->change_bits.  In this situation that bit is interpreted as
though a connect-change event had occurred on the port _after_ the
reset-resume, which is not what actually happened.

One possible fix would be to make the reset-resume code clear the
port's bit in hub->change_bits.  But it seems simpler to just avoid
setting the bit during hub_activate() in the first place.  That's what
this patch does.

(Proving that the patch is correct when CONFIG_PM is disabled requires
a little thought.  In that setting hub_activate() will be called only
for initialization and resets, since there won't be any resumes or
reset-resumes.  During initialization and hub resets the hub doesn't
have any child devices, and so this code path never gets executed.)

Reported-and-tested-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://marc.info/?t=157949360700001&r=1&w=2
CC: David Heinzelmann <heinzelmann.david@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Fix novation SourceControl XL after suspend

commit b692056db8ecc7f452b934f016c17348282b7699 upstream.

Currently, the SourceControl will stay in power-down mode after resuming
from suspend. This patch resets the device after suspend to power it up.

Signed-off-by: Richard Dodd <richard.o.dodd@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212142220.36892-1-richard.o.dodd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: uas: fix a plug & unplug racing

commit 3e99862c05a9caa5a27969f41566b428696f5a9a upstream.

When a uas disk is plugged into an external hub, uas_probe()
will be called by the hub thread to do the probe. It will
first create a SCSI host and then do the scan for this host.
During the scan, it will probe the LUN using SCSI INQUERY command
which will be packed in the URB and submitted to uas disk.

There might be a chance that this external hub with uas disk
attached is unplugged during the scan. In this case, uas driver
will fail to submit the URB (due to the NOTATTACHED state of uas
device) and try to put this SCSI command back to request queue
waiting for next chance to run.

In normal case, this cycle will terminate when hub thread gets
disconnection event and calls into uas_disconnect() accordingly.
But in this case, uas_disconnect() will not be called because
hub thread of external hub gets stuck waiting for the completion
of this SCSI command. A deadlock happened.

In this fix, uas will call scsi_scan_host() asynchronously to
avoid the blocking of hub thread.

Signed-off-by: EJ Hsu <ejh@nvidia.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200130092506.102760-1-ejh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: quirks: blacklist duplicate ep on Sound Devices USBPre2

commit bdd1b147b8026df0e4260b387026b251d888ed01 upstream.

This device has a broken vendor-specific altsetting for interface 1,
where endpoint 0x85 is declared as an isochronous endpoint despite being
used by interface 2 for audio capture.

Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass          239 Miscellaneous Device
  bDeviceSubClass         2
  bDeviceProtocol         1 Interface Association
  bMaxPacketSize0        64
  idVendor           0x0926
  idProduct          0x0202
  bcdDevice            1.00
  iManufacturer           1 Sound Devices
  iProduct                2 USBPre2
  iSerial                 3 [...]
  bNumConfigurations      1

[...]

    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       3
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            5
          Transfer Type            Isochronous
          Synch Type               Asynchronous
          Usage Type               Data
        wMaxPacketSize     0x0126  1x 294 bytes
        bInterval               1

[...]

    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       1
      bNumEndpoints           1
      bInterfaceClass         1 Audio
      bInterfaceSubClass      2 Streaming
      bInterfaceProtocol      0
      iInterface              0
      AudioStreaming Interface Descriptor:
        bLength                 7
        bDescriptorType        36
        bDescriptorSubtype      1 (AS_GENERAL)
        bTerminalLink           4
        bDelay                  1 frames
        wFormatTag         0x0001 PCM
      AudioStreaming Interface Descriptor:
        bLength                26
        bDescriptorType        36
        bDescriptorSubtype      2 (FORMAT_TYPE)
        bFormatType             1 (FORMAT_TYPE_I)
        bNrChannels             2
        bSubframeSize           2
        bBitResolution         16
        bSamFreqType            6 Discrete
        tSamFreq[ 0]         8000
        tSamFreq[ 1]        16000
        tSamFreq[ 2]        24000
        tSamFreq[ 3]        32000
        tSamFreq[ 4]        44100
        tSamFreq[ 5]        48000
      Endpoint Descriptor:
        bLength                 9
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            5
          Transfer Type            Isochronous
          Synch Type               Asynchronous
          Usage Type               Data
        wMaxPacketSize     0x0126  1x 294 bytes
        bInterval               4
        bRefresh                0
        bSynchAddress           0
        AudioStreaming Endpoint Descriptor:
          bLength                 7
          bDescriptorType        37
          bDescriptorSubtype      1 (EP_GENERAL)
          bmAttributes         0x01
            Sampling Frequency
          bLockDelayUnits         2 Decoded PCM samples
          wLockDelay         0x0000

Since commit 3e4f8e21c4f2 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing, but in this case we need to ignore the first
instance in order to avoid breaking the audio capture interface.

Fixes: 3e4f8e21c4f2 ("USB: core: fix check for duplicate endpoints")
Cc: stable <stable@vger.kernel.org>
Reported-by: edes <edes@gmx.net>
Tested-by: edes <edes@gmx.net>
Link: https://lore.kernel.org/r/20200201105829.5682c887@acme7.acmenet
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: add endpoint-blacklist quirk

commit 73f8bda9b5dc1c69df2bc55c0cbb24461a6391a9 upstream.

Add a new device quirk that can be used to blacklist endpoints.

Since commit 3e4f8e21c4f2 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.

In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.

Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: host: xhci: update event ring dequeue pointer on purpose

commit dc0ffbea5729a3abafa577ebfce87f18b79e294b upstream.

On some situations, the software handles TRB events slower
than adding TRBs, then xhci_handle_event can't return zero
long time, the xHC will consider the event ring is full,
and trigger "Event Ring Full" error, but in fact, the software
has already finished lots of events, just no chance to
update ERDP (event ring dequeue pointer).

In this commit, we force update ERDP if half of TRBS_PER_SEGMENT
events have handled to avoid "Event Ring Full" error.

Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2

commit cf0ee7c60c89641f6e4d1d3c7867fe32b9e30300 upstream.

xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.

Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.

To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.

When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.

Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8be ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: apply XHCI_PME_STUCK_QUIRK to Intel Comet Lake platforms

commit a3ae87dce3a5abe0b57c811bab02b2564b574106 upstream.

Intel Comet Lake based platform require the XHCI_PME_STUCK_QUIRK
quirk as well. Without this xHC can not enter D3 in runtime suspend.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: fix runtime pm enabling for quirky Intel hosts

commit 024d411e9c5d49eb96c825af52a3ce2682895676 upstream.

Intel hosts that need the XHCI_PME_STUCK_QUIRK flag should enable
runtime pm by calling xhci_pme_acpi_rtd3_enable() before
usb_hcd_pci_probe() calls pci_dev_run_wake().
Otherwise usage count for the device won't be decreased, and runtime
suspend is prevented.

usb_hcd_pci_probe() only decreases the usage count if device can
generate run-time wake-up events, i.e. when pci_dev_run_wake()
returns true.

This issue was exposed by pci_dev_run_wake() change in
commit 8feaec33b986 ("PCI / PM: Always check PME wakeup capability for
runtime wakeup support")
and should be backported to kernels with that change

Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Force Maximum Packet size for Full-speed bulk devices to valid range.

commit f148b9f402ef002b57bcff3964d45abc8ffb6c3f upstream.

A Full-speed bulk USB audio device (DJ-Tech CTRL) with a invalid Maximum
Packet Size of 4 causes a xHC "Parameter Error" at enumeration.

This is because valid Maximum packet sizes for Full-speed bulk endpoints
are 8, 16, 32 and 64 bytes. Hosts are not required to support other values
than these. See usb 2 specs section 5.8.3 for details.

The device starts working after forcing the maximum packet size to 8.
This is most likely the case with other devices as well, so force the
maximum packet size to a valid range.

Cc: stable@vger.kernel.org
Reported-by: Rene D Obermueller <cmdrrdo@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: vt6656: fix sign of rx_dbm to bb_pre_ed_rssi.

commit 93134df520f23f4e9998c425b8987edca7016817 upstream.

bb_pre_ed_rssi is an u8 rx_dm always returns negative signed
values add minus operator to always yield positive.

fixes issue where rx sensitivity is always set to maximum because
the unsigned numbers were always greater then 100.

Fixes: 63b9907f58f1 ("staging: vt6656: mac80211 conversion: create rx function.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/aceac98c-6e69-3ce1-dfec-2bf27b980221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: android: ashmem: Disallow ashmem memory from being remapped

commit 6d67b0290b4b84c477e6a2fc6e005e174d3c7786 upstream.

When ashmem file is mmapped, the resulting vma->vm_file points to the
backing shmem file with the generic fops that do not check ashmem
permissions like fops of ashmem do. If an mremap is done on the ashmem
region, then the permission checks will be skipped. Fix that by disallowing
mapping operation on the backing shmem file.

Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Cc: stable <stable@vger.kernel.org> # 4.4,4.9,4.14,4.18,5.4
Signed-off-by: Todd Kjos <tkjos@google.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Link: https://lore.kernel.org/r/20200127235616.48920-1-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt: vt_ioctl: fix race in VT_RESIZEX

commit 6cd1ed50efd88261298577cd92a14f2768eddeeb upstream.

We need to make sure vc_cons[i].d is not NULL after grabbing
console_lock(), or risk a crash.

general protection fault, probably for non-canonical address 0xdffffc0000000068: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000340-0x0000000000000347]
CPU: 1 PID: 19462 Comm: syz-executor.5 Not tainted 5.5.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:vt_ioctl+0x1f96/0x26d0 drivers/tty/vt/vt_ioctl.c:883
Code: 74 41 e8 bd a6 84 fd 48 89 d8 48 c1 e8 03 42 80 3c 28 00 0f 85 e4 04 00 00 48 8b 03 48 8d b8 40 03 00 00 48 89 fa 48 c1 ea 03 <42> 0f b6 14 2a 84 d2 74 09 80 fa 03 0f 8e b1 05 00 00 44 89 b8 40
RSP: 0018:ffffc900086d7bb0 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffffffff8c34ee88 RCX: ffffc9001415c000
RDX: 0000000000000068 RSI: ffffffff83f0e6e3 RDI: 0000000000000340
RBP: ffffc900086d7cd0 R08: ffff888054ce0100 R09: fffffbfff16a2f6d
R10: ffff888054ce0998 R11: ffff888054ce0100 R12: 000000000000001d
R13: dffffc0000000000 R14: 1ffff920010daf79 R15: 000000000000ff7f
FS:  00007f7d13c12700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffd477e3c38 CR3: 0000000095d0a000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 tty_ioctl+0xa37/0x14f0 drivers/tty/tty_io.c:2660
 vfs_ioctl fs/ioctl.c:47 [inline]
 ksys_ioctl+0x123/0x180 fs/ioctl.c:763
 __do_sys_ioctl fs/ioctl.c:772 [inline]
 __se_sys_ioctl fs/ioctl.c:770 [inline]
 __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:770
 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x45b399
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f7d13c11c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007f7d13c126d4 RCX: 000000000045b399
RDX: 0000000020000080 RSI: 000000000000560a RDI: 0000000000000003
RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 0000000000000666 R14: 00000000004c7f04 R15: 000000000075bf2c
Modules linked in:
---[ end trace 80970faf7a67eb77 ]---
RIP: 0010:vt_ioctl+0x1f96/0x26d0 drivers/tty/vt/vt_ioctl.c:883
Code: 74 41 e8 bd a6 84 fd 48 89 d8 48 c1 e8 03 42 80 3c 28 00 0f 85 e4 04 00 00 48 8b 03 48 8d b8 40 03 00 00 48 89 fa 48 c1 ea 03 <42> 0f b6 14 2a 84 d2 74 09 80 fa 03 0f 8e b1 05 00 00 44 89 b8 40
RSP: 0018:ffffc900086d7bb0 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffffffff8c34ee88 RCX: ffffc9001415c000
RDX: 0000000000000068 RSI: ffffffff83f0e6e3 RDI: 0000000000000340
RBP: ffffc900086d7cd0 R08: ffff888054ce0100 R09: fffffbfff16a2f6d
R10: ffff888054ce0998 R11: ffff888054ce0100 R12: 000000000000001d
R13: dffffc0000000000 R14: 1ffff920010daf79 R15: 000000000000ff7f
FS:  00007f7d13c12700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffd477e3c38 CR3: 0000000095d0a000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20200210190721.200418-1-edumazet@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt: selection, handle pending signals in paste_selection

commit 687bff0cd08f790d540cfb7b2349f0d876cdddec upstream.

When pasting a selection to a vt, the task is set as INTERRUPTIBLE while
waiting for a tty to unthrottle. But signals are not handled at all.
Normally, this is not a problem as tty_ldisc_receive_buf receives all
the goods and a user has no reason to interrupt the task.

There are two scenarios where this matters:
1) when the tty is throttled and a signal is sent to the process, it
   spins on a CPU until the tty is unthrottled. schedule() does not
   really echedule, but returns immediately, of course.
2) when the sel_buffer becomes invalid, KASAN prevents any reads from it
   and the loop simply does not proceed and spins forever (causing the
   tty to throttle, but the code never sleeps, the same as above). This
   sometimes happens as there is a race in the sel_buffer handling code.

So add signal handling to this ioctl (TIOCL_PASTESEL) and return -EINTR
in case a signal is pending.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210081131.23572-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt: fix scrollback flushing on background consoles

commit 3f4ef485be9d54040b695f32ec76d0f1ea50bbf3 upstream.

Commit a6dbe4427559 ("vt: perform safe console erase in the right
order") provided fixes to an earlier commit by gathering all console
scrollback flushing operations in a function of its own. This includes
the invocation of vc_sw->con_switch() as previously done through a
update_screen() call. That commit failed to carry over the
con_is_visible() conditional though, as well as cursor handling, which
caused problems when "\e[3J" was written to a background console.

One could argue for preserving the call to update_screen(). However
this does far more than we need, and it is best to remove scrollback
assumptions from it. Instead let's gather the minimum needed to actually
perform scrollback flushing properly in that one place.

While at it, let's document the vc_sw->con_switch() side effect being
relied upon.

Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-and-tested-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2001281205560.1655@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

floppy: check FDC index for errors before assigning it

commit 2e90ca68b0d2f5548804f22f0dd61145516171e3 upstream.

Jordy Zomer reported a KASAN out-of-bounds read in the floppy driver in
wait_til_ready().

Which on the face of it can't happen, since as Willy Tarreau points out,
the function does no particular memory access.  Except through the FDCS
macro, which just indexes a static allocation through teh current fdc,
which is always checked against N_FDC.

Except the checking happens after we've already assigned the value.

The floppy driver is a disgrace (a lot of it going back to my original
horrd "design"), and has no real maintainer.  Nobody has the hardware,
and nobody really cares.  But it still gets used in virtual environment
because it's one of those things that everybody supports.

The whole thing should be re-written, or at least parts of it should be
seriously cleaned up.  The 'current fdc' index, which is used by the
FDCS macro, and which is often shadowed by a local 'fdc' variable, is a
prime example of how not to write code.

But because nobody has the hardware or the motivation, let's just fix up
the immediate problem with a nasty band-aid: test the fdc index before
actually assigning it to the static 'fdc' variable.

Reported-by: Jordy Zomer <jordy@simplyhacker.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: Use rtnl_lock to prevent race conditions between net and pci/pm

commit a7023819404ac9bd2bb311a4fafd38515cfa71ec upstream.

This patch is meant to address possible race conditions that can exist
between network configuration and power management. A similar issue was
fixed for igb in commit 9474933caf21 ("igb: close/suspend race in
netif_device_detach").

In addition it consolidates the code so that the PCI error handling code
will essentially perform the power management freeze on the device prior to
attempting a reset, and will thaw the device afterwards if that is what it
is planning to do. Otherwise when we call close on the interface it should
see it is detached and not attempt to call the logic to down the interface
and free the IRQs again.

From what I can tell the check that was adding the check for __E1000_DOWN
in e1000e_close was added when runtime power management was added. However
it should not be relevant for us as we perform a call to
pm_runtime_get_sync before we call e1000_down/free_irq so it should always
be back up before we call into this anyway.

Reported-by: Morumuri Srivalli <smorumu1@in.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: misc: iowarrior: add support for the 100 device

commit bab5417f5f0118ce914bc5b2f8381e959e891155 upstream.

Add a new device id for the 100 devie.  It has 4 interfaces like the 28
and 28L devices but a larger endpoint so more I/O pins.

Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200214161148.GA3963518@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: misc: iowarrior: add support for the 28 and 28L devices

commit 5f6f8da2d7b5a431d3f391d0d73ace8edfb42af7 upstream.

Add new device ids for the 28 and 28L devices.  These have 4 interfaces
instead of 2, but the driver binds the same, so the driver changes are
minimal.

Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: misc: iowarrior: add support for 2 OEMed devices

commit 461d8deb26a7d70254bc0391feb4fd8a95e674e8 upstream.

Add support for two OEM devices that are identical to existing
IO-Warrior devices, except for the USB device id.

Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thunderbolt: Prevent crash if non-active NVMem file is read

commit 03cd45d2e219301880cabc357e3cf478a500080f upstream.

The driver does not populate .reg_read callback for the non-active NVMem
because the file is supposed to be write-only. However, it turns out
NVMem subsystem does not yet support this and expects that the .reg_read
callback is provided. If user reads the binary attribute it triggers
NULL pointer dereference like this one:

  BUG: kernel NULL pointer dereference, address: 0000000000000000
  ...
  Call Trace:
   bin_attr_nvmem_read+0x64/0x80
   kernfs_fop_read+0xa7/0x180
   vfs_read+0xbd/0x170
   ksys_read+0x5a/0xd0
   do_syscall_64+0x43/0x150
   entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fix this in the driver by providing .reg_read callback that always
returns an error.

Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Fixes: e6b245ccd524 ("thunderbolt: Add support for host and device NVM firmware upgrade")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200213095604.1074-1-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: handle logged extent failure properly

commit bd727173e4432fe6cb70ba108dc1f3602c5409d7 upstream.

If we're allocating a logged extent we attempt to insert an extent
record for the file extent directly.  We increase
space_info->bytes_reserved, because the extent entry addition will call
btrfs_update_block_group(), which will convert the ->bytes_reserved to
->bytes_used.  However if we fail at any point while inserting the
extent entry we will bail and leave space on ->bytes_reserved, which
will trigger a WARN_ON() on umount.  Fix this by pinning the space if we
fail to insert, which is what happens in every other failure case that
involves adding the extent entry.

CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ecryptfs: fix a memory leak bug in ecryptfs_init_messaging()

commit b4a81b87a4cfe2bb26a4a943b748d96a43ef20e8 upstream.

In ecryptfs_init_messaging(), if the allocation for 'ecryptfs_msg_ctx_arr'
fails, the previously allocated 'ecryptfs_daemon_hash' is not deallocated,
leading to a memory leak bug. To fix this issue, free
'ecryptfs_daemon_hash' before returning the error.

Cc: stable@vger.kernel.org
Fixes: 88b4a07e6610 ("[PATCH] eCryptfs: Public key transport mechanism")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ecryptfs: fix a memory leak bug in parse_tag_1_packet()

commit fe2e082f5da5b4a0a92ae32978f81507ef37ec66 upstream.

In parse_tag_1_packet(), if tag 1 packet contains a key larger than
ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES, no cleanup is executed, leading to a
memory leak on the allocated 'auth_tok_list_item'. To fix this issue, go to
the label 'out_free' to perform the cleanup work.

Cc: stable@vger.kernel.org
Fixes: dddfa461fc89 ("[PATCH] eCryptfs: Public key; packet management")
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tpm: Initialize crypto_id of allocated_banks to HASH_ALGO__LAST

commit dc10e4181c05a2315ddc375e963b7c763b5ee0df upstream.

chip->allocated_banks, an array of tpm_bank_info structures, contains the
list of TPM algorithm IDs of allocated PCR banks. It also contains the
corresponding ID of the crypto subsystem, so that users of the TPM driver
can calculate a digest for a PCR extend operation.

However, if there is no mapping between TPM algorithm ID and crypto ID, the
crypto_id field of tpm_bank_info remains set to zero (the array is
allocated and initialized with kcalloc() in tpm2_get_pcr_allocation()).
Zero should not be used as value for unknown mappings, as it is a valid
crypto ID (HASH_ALGO_MD4).

Thus, initialize crypto_id to HASH_ALGO__LAST.

Cc: stable@vger.kernel.org # 5.1.x
Fixes: 879b589210a9 ("tpm: retrieve digest size of unknown algorithms with PCR read")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: sun8i-codec: Fix setting DAI data format

commit 96781fd941b39e1f78098009344ebcd7af861c67 upstream.

Use the correct mask for this two-bit field. This fixes setting the DAI
data format to RIGHT_J or DSP_A.

Fixes: 36c684936fae ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20200217064250.15516-7-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: codec2codec: avoid invalid/double-free of pcm runtime

commit b6570fdb96edf45bcf71884bd2644bd73d348d1a upstream.

The PCM runtime was freed during PMU in the case that the event hook
encountered an error. However, it is also unconditionally freed during
PMD. Avoid a double-free by dropping the call to kfree in the PMU hook.

Fixes: a72706ed8208 ("ASoC: codec2codec: remove ephemeral variables")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200213061147.29386-2-samuel@sholland.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Apply quirk for yet another MSI laptop

commit cc5049ae4d457194796f854eb2e38b9727ad8c2d upstream.

MSI GP65 laptop with SSID 1462:1293 requires the same quirk as other
MSI models.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204159
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200218080915.3433-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Apply quirk for MSI GP63, too

commit a655e2b107d463ce2745188ce050d07daed09a71 upstream.

The same quirk that was applied to MSI GL73 is needed for MSI GP63,
too.  Adding the entry with the SSID 1462:1228.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206503
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200217151947.17528-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Use scnprintf() for printing texts for sysfs/procfs

commit 44eeb081b8630bb3ad3cd381d1ae1831463e48bb upstream.

Some code in HD-audio driver calls snprintf() in a loop and still
expects that the return value were actually written size, while
snprintf() returns the expected would-be length instead.  When the
given buffer limit were small, this leads to a buffer overflow.

Use scnprintf() for addressing those issues.  It returns the actually
written size unlike snprintf().

Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200218091409.27162-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/qcom: Fix bogus detach logic

commit faf305c51aeabd1ea2d7131e798ef5f55f4a7750 upstream.

Currently, the implementation of qcom_iommu_domain_free() is guaranteed
to do one of two things: WARN() and leak everything, or dereference NULL
and crash. That alone is terrible, but in fact the whole idea of trying
to track the liveness of a domain via the qcom_domain->iommu pointer as
a sanity check is full of fundamentally flawed assumptions. Make things
robust and actually functional by not trying to be quite so clever.

Reported-by: Brian Masney <masneyb@onstation.org>
Tested-by: Brian Masney <masneyb@onstation.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 0ae349a0f33f ("iommu/qcom: Add qcom_iommu")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.4.22

rtc: Kconfig: select REGMAP_I2C when necessary

[ Upstream commit 578c2b661e2b1b474ea3571a3c3c6d57bae89e8d ]

Some i2c RTC drivers are using regmap but are not selecting REGMAP_I2C
which may lead to build failures.

Link: https://lore.kernel.org/r/20200127221724.10160-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bcache: properly initialize 'path' and 'err' in register_bcache()

[ Upstream commit 29cda393bcaad160c4bf3676ddd99855adafc72f ]

Patch "bcache: rework error unwinding in register_bcache" from
Christoph Hellwig changes the local variables 'path' and 'err'
in undefined initial state. If the code in register_bcache() jumps
to label 'out:' or 'out_module_put:' by goto, these two variables
might be reference with undefined value by the following line,

out_module_put:
        module_put(THIS_MODULE);
out:
        pr_info("error %s: %s", path, err);
        return ret;

Therefore this patch initializes these two local variables properly
in register_bcache() to avoid such issue.

Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu/display: handle multiple numbers of fclks in dcn_calcs.c (v2)

[ Upstream commit c37243579d6c881c575dcfb54cf31c9ded88f946 ]

We might get different numbers of clocks from powerplay depending
on what the OEM has populated.

v2: add assert for at least one level

Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/pci: Recover handle in clp_set_pci_fn()

[ Upstream commit 17cdec960cf776b20b1fb08c622221babe591d51 ]

When we try to recover a PCI function using

    echo 1 > /sys/bus/pci/devices/<id>/recover

or manually with

    echo 1 > /sys/bus/pci/devices/<id>/remove
    echo 0 > /sys/bus/pci/slots/<slot>/power
    echo 1 > /sys/bus/pci/slots/<slot>/power

clp_disable_fn() / clp_enable_fn() call clp_set_pci_fn() to first
disable and then reenable the function.

When the function is already in the requested state we may be left with
an invalid function handle.

To get a new valid handle we do a clp_list_pci() call. For this we need
both the function ID and function handle in clp_set_pci_fn() so pass the
zdev and get both.

To simplify things also pull setting the refreshed function handle into
clp_set_pci_fn()

Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum_dpipe: Add missing error path

[ Upstream commit 3a99cbb6fa7bca1995586ec2dc21b0368aad4937 ]

In case devlink_dpipe_entry_ctx_prepare() failed, release RTNL that was
previously taken and free the memory allocated by
mlxsw_sp_erif_entry_prepare().

Fixes: 2ba5999f009d ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fuse: don't overflow LLONG_MAX with end offset

[ Upstream commit 2f1398291bf35fe027914ae7a9610d8e601fbfde ]

Handle the special case of fuse_readpages() wanting to read the last page
of a hugest file possible and overflowing the end offset in the process.

This is basically to unbreak xfstests:generic/525 and prevent filesystems
from doing bad things with an overflowing offset.

Reported-by: Xiao Yang <ice_yangxiao@163.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

virtio_balloon: prevent pfn array overflow

[ Upstream commit 6e9826e77249355c09db6ba41cd3f84e89f4b614 ]

Make sure, at build time, that pfn array is big enough to hold a single
page.  It happens to be true since the PAGE_SHIFT value at the moment is
20, which is 1M - exactly 256 4K balloon pages.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cifs: log warning message (once) if out of disk space

[ Upstream commit d6fd41905ec577851734623fb905b1763801f5ef ]

We ran into a confusing problem where an application wasn't checking
return code on close and so user didn't realize that the application
ran out of disk space.  log a warning message (once) in these
cases. For example:

  [ 8407.391909] Out of space writing to \\oleg-server\small-share

Signed-off-by: Steve French <stfrench@microsoft.com>
Reported-by: Oleg Kravtsov <oleg@tuxera.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: Relax i40e_xsk_wakeup's return value when PF is busy

[ Upstream commit c77e9f09143822623dd71a0fdc84331129e97c3a ]

Return -EAGAIN instead of -ENETDOWN to provide a slightly milder
information to user space so that an application will know to retry the
syscall when __I40E_CONFIG_BUSY bit is set on pf->state.

Fixes: b3873a5be757 ("net/i40e: Fix concurrency issues between config flow and XSK")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20200205045834.56795-2-maciej.fijalkowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

help_next should increase position index

[ Upstream commit 9f198a2ac543eaaf47be275531ad5cbd50db3edf ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFS: Fix memory leaks

[ Upstream commit 123c23c6a7b7ecd2a3d6060bea1d94019f71fd66 ]

In _nfs42_proc_copy(), 'res->commit_res.verf' is allocated through
kzalloc() if 'args->sync' is true. In the following code, if
'res->synchronous' is false, handle_async_copy() will be invoked. If an
error occurs during the invocation, the following code will not be executed
and the error will be returned . However, the allocated
'res->commit_res.verf' is not deallocated, leading to a memory leak. This
is also true if the invocation of process_copy_commit() returns an error.

To fix the above leaks, redirect the execution to the 'out' label if an
error is encountered.

Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu/smu10: fix smu10_get_clock_by_type_with_voltage

[ Upstream commit 1064ad4aeef94f51ca230ac639a9e996fb7867a0 ]

Cull out 0 clocks to avoid a warning in DC.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu/smu10: fix smu10_get_clock_by_type_with_latency

[ Upstream commit 4d0a72b66065dd7e274bad6aa450196d42fd8f84 ]

Only send non-0 clocks to DC for validation.  This mirrors
what the windows driver does.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

brd: check and limit max_part par

[ Upstream commit c8ab422553c81a0eb070329c63725df1cd1425bc ]

In brd_init func, rd_nr num of brd_device are firstly allocated
and add in brd_devices, then brd_devices are traversed to add each
brd_device by calling add_disk func. When allocating brd_device,
the disk->first_minor is set to i * max_part, if rd_nr * max_part
is larger than MINORMASK, two different brd_device may have the same
devt, then only one of them can be successfully added.
when rmmod brd.ko, it will cause oops when calling brd_exit.

Follow those steps:
  # modprobe brd rd_nr=3 rd_size=102400 max_part=1048576
  # rmmod brd
then, the oops will appear.

Oops log:
[  726.613722] Call trace:
[  726.614175]  kernfs_find_ns+0x24/0x130
[  726.614852]  kernfs_find_and_get_ns+0x44/0x68
[  726.615749]  sysfs_remove_group+0x38/0xb0
[  726.616520]  blk_trace_remove_sysfs+0x1c/0x28
[  726.617320]  blk_unregister_queue+0x98/0x100
[  726.618105]  del_gendisk+0x144/0x2b8
[  726.618759]  brd_exit+0x68/0x560 [brd]
[  726.619501]  __arm64_sys_delete_module+0x19c/0x2a0
[  726.620384]  el0_svc_common+0x78/0x130
[  726.621057]  el0_svc_handler+0x38/0x78
[  726.621738]  el0_svc+0x8/0xc
[  726.622259] Code: aa0203f6 aa0103f7 aa1e03e0 d503201f (7940e260)

Here, we add brd_check_and_reset_par func to check and limit max_part par.

--
V5->V6:
 - remove useless code

V4->V5:(suggested by Ming Lei)
 - make sure max_part is not larger than DISK_MAX_PARTS

V3->V4:(suggested by Ming Lei)
 - remove useless change
 - add one limit of max_part

V2->V3: (suggested by Ming Lei)
 - clear .minors when running out of consecutive minor space in brd_alloc
 - remove limit of rd_nr

V1->V2:
 - add more checks in brd_check_par_valid as suggested by Ming Lei.

Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

microblaze: Prevent the overflow of the start

[ Upstream commit 061d2c1d593076424c910cb1b64ecdb5c9a6923f ]

In case the start + cache size is more than the max int the
start overflows.
Prevent the same.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

asm-generic/tlb: add missing CONFIG symbol

[ Upstream commit 27796d03c9c4b2b937ed4cc2b10f21559ad5a8c9 ]

Without this the symbol will not actually end up in .config files.

Link: http://lkml.kernel.org/r/20200116064531.483522-6-aneesh.kumar@linux.ibm.com
Fixes: a30e32bd79e9 ("asm-generic/tlb: Provide generic tlb_flush() based on flush_tlb_mm()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: Check the sta is not NULL in iwl_mvm_cfg_he_sta()

[ Upstream commit 12d47f0ea5e0aa63f19ba618da55a7c67850ca10 ]

Fix a kernel panic by checking that the sta is not NULL.
This could happen during a reconfig flow, as mac80211 moves the sta
between all the states without really checking if the previous state was
successfully set. So, if for some reason we failed to add back the
station, subsequent calls to sta_state() callback will be done when the
station is NULL. This would result in a following panic:

BUG: unable to handle kernel NULL pointer dereference at
0000000000000040
IP: iwl_mvm_cfg_he_sta+0xfc/0x690 [iwlmvm]
[..]
Call Trace:
 iwl_mvm_mac_sta_state+0x629/0x6f0 [iwlmvm]
 drv_sta_state+0xf4/0x950 [mac80211]
 ieee80211_reconfig+0xa12/0x2180 [mac80211]
 ieee80211_restart_work+0xbb/0xe0 [mac80211]
 process_one_work+0x1e2/0x610
 worker_thread+0x4d/0x3e0
[..]

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: Fix thermal zone registration

[ Upstream commit baa6cf8450b72dcab11f37c47efce7c5b9b8ad0f ]

Use a unique name when registering a thermal zone. Otherwise, with
multiple NICS, we hit the following warning during the unregistration.

WARNING: CPU: 2 PID: 3525 at fs/sysfs/group.c:255
 RIP: 0010:sysfs_remove_group+0x80/0x90
 Call Trace:
  dpm_sysfs_remove+0x57/0x60
  device_del+0x5a/0x350
  ? sscanf+0x4e/0x70
  device_unregister+0x1a/0x60
  hwmon_device_unregister+0x4a/0xa0
  thermal_remove_hwmon_sysfs+0x175/0x1d0
  thermal_zone_device_unregister+0x188/0x1e0
  iwl_mvm_thermal_exit+0xe7/0x100 [iwlmvm]
  iwl_op_mode_mvm_stop+0x27/0x180 [iwlmvm]
  _iwl_op_mode_stop.isra.3+0x2b/0x50 [iwlwifi]
  iwl_opmode_deregister+0x90/0xa0 [iwlwifi]
  __exit_compat+0x10/0x2c7 [iwlmvm]
  __x64_sys_delete_module+0x13f/0x270
  do_syscall_64+0x5a/0x110
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-pci: remove nvmeq->tags

[ Upstream commit cfa27356f835dc7755192e7b941d4f4851acbcc7 ]

There is no real need to have a pointer to the tagset in
struct nvme_queue, as we only need it in a single place, and that place
can derive the used tagset from the device and qid trivially.  This
fixes a problem with stale pointer exposure when tagsets are reset,
and also shrinks the nvme_queue structure.  It also matches what most
other transports have done since day 1.

Reported-by: Edmund Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvmet: Pass lockdep expression to RCU lists

[ Upstream commit 4ac76436a6d07dec1c3c766f234aa787a16e8f65 ]

ctrl->subsys->namespaces and subsys->namespaces are traversed with
list_for_each_entry_rcu outside an RCU read-side critical section but
under the protection of ctrl->subsys->lock and subsys->lock respectively.

Hence, add the corresponding lockdep expression to the list traversal
primitive to silence false-positive lockdep warnings, and harden RCU
lists.

Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL

[ Upstream commit 107945227ac5d4c37911c7841b27c64b489ce9a9 ]

It looks like an obvious mistake to use its_mapc_cmd descriptor when
building the INVALL command block. It so far worked by luck because
both its_mapc_cmd.col and its_invall_cmd.col sit at the same offset of
the ITS command descriptor, but we should not rely on it.

Fixes: cc2d3216f53c ("irqchip: GICv3: ITS command queue")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191202071021.1251-1-yuzenghui@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

bcache: fix incorrect data type usage in btree_flush_write()

[ Upstream commit d1c3cc34f5a78b38d2b809b289d912c3560545df ]

Dan Carpenter points out that from commit 2aa8c529387c ("bcache: avoid
unnecessary btree nodes flushing in btree_flush_write()"), there is a
incorrect data type usage which leads to the following static checker
warning:
drivers/md/bcache/journal.c:444 btree_flush_write()
warn: 'ref_nr' unsigned <= 0

drivers/md/bcache/journal.c
   422  static void btree_flush_write(struct cache_set *c)
   423  {
   424          struct btree *b, *t, *btree_nodes[BTREE_FLUSH_NR];
   425          unsigned int i, nr, ref_nr;
                                    ^^^^^^

   426          atomic_t *fifo_front_p, *now_fifo_front_p;
   427          size_t mask;
   428
   429          if (c->journal.btree_flushing)
   430                  return;
   431
   432          spin_lock(&c->journal.flush_write_lock);
   433          if (c->journal.btree_flushing) {
   434                  spin_unlock(&c->journal.flush_write_lock);
   435                  return;
   436          }
   437          c->journal.btree_flushing = true;
   438          spin_unlock(&c->journal.flush_write_lock);
   439
   440          /* get the oldest journal entry and check its refcount */
   441          spin_lock(&c->journal.lock);
   442          fifo_front_p = &fifo_front(&c->journal.pin);
   443          ref_nr = atomic_read(fifo_front_p);
   444          if (ref_nr <= 0) {
                    ^^^^^^^^^^^
Unsigned can't be less than zero.

   445                  /*
   446                   * do nothing if no btree node references
   447                   * the oldest journal entry
   448                   */
   449                  spin_unlock(&c->journal.lock);
   450                  goto out;
   451          }
   452          spin_unlock(&c->journal.lock);

As the warning information indicates, local varaible ref_nr in unsigned
int type is wrong, which does not matche atomic_read() and the "<= 0"
checking.

This patch fixes the above error by defining local variable ref_nr as
int type.

Fixes: 2aa8c529387c ("bcache: avoid unnecessary btree nodes flushing in btree_flush_write()")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bcache: explicity type cast in bset_bkey_last()

[ Upstream commit 7c02b0055f774ed9afb6e1c7724f33bf148ffdc0 ]

In bset.h, macro bset_bkey_last() is defined as,
    bkey_idx((struct bkey *) (i)->d, (i)->keys)

Parameter i can be variable type of data structure, the macro always
works once the type of struct i has member 'd' and 'keys'.

bset_bkey_last() is also used in macro csum_set() to calculate the
checksum of a on-disk data structure. When csum_set() is used to
calculate checksum of on-disk bcache super block, the parameter 'i'
data type is struct cache_sb_disk. Inside struct cache_sb_disk (also in
struct cache_sb) the member keys is __u16 type. But bkey_idx() expects
unsigned int (a 32bit width), so there is problem when sending
parameters via stack to call bkey_idx().

Sparse tool from Intel 0day kbuild system reports this incompatible
problem. bkey_idx() is part of user space API, so the simplest fix is
to cast the (i)->keys to unsigned int type in macro bset_bkey_last().

Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bcache: fix memory corruption in bch_cache_accounting_clear()

[ Upstream commit 5bebf7486d4f4940b2a8e4009beb1dff5041853d ]

Commit 83ff9318c44ba ("bcache: not use hard coded memset size in
bch_cache_accounting_clear()") tries to make the code more easy to
understand by removing the hard coded number with following change,
void bch_cache_accounting_clear(...)
{
memset(&acc->total.cache_hits,
0,
- sizeof(unsigned long) * 7);
+ sizeof(struct cache_stats));
}

Unfortunately the change was wrong (it also tells us the original code
was not easy to correctly understand). The hard coded number 7 is used
because in struct cache_stats,
 15 struct cache_stats {
 16         struct kobject          kobj;
 17
 18         unsigned long cache_hits;
 19         unsigned long cache_misses;
 20         unsigned long cache_bypass_hits;
 21         unsigned long cache_bypass_misses;
 22         unsigned long cache_readaheads;
 23         unsigned long cache_miss_collisions;
 24         unsigned long sectors_bypassed;
 25
 26         unsigned int            rescale;
 27 };
only members in LINE 18-24 want to be set to 0. It is wrong to use
'sizeof(struct cache_stats)' to replace 'sizeof(unsigned long) * 7), the
memory objects behind acc->total is staled by this change.

Сорокин Артем Сергеевич reports that by the following steps, kernel
panic will be triggered,
1. Create new set: make-bcache -B /dev/nvme1n1 -C /dev/sda --wipe-bcache
2. Run in /sys/fs/bcache/<uuid>:
   echo 1 > clear_stats && cat stats_five_minute/cache_bypass_hits

I can reproduce the panic and get following dmesg with KASAN enabled,
[22613.172742] ==================================================================
[22613.172862] BUG: KASAN: null-ptr-deref in sysfs_kf_seq_show+0x117/0x230
[22613.172864] Read of size 8 at addr 0000000000000000 by task cat/6753

[22613.172870] CPU: 1 PID: 6753 Comm: cat Not tainted 5.5.0-rc7-lp151.28.16-default+ #11
[22613.172872] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/29/2019
[22613.172873] Call Trace:
[22613.172964]  dump_stack+0x8b/0xbb
[22613.172968]  ? sysfs_kf_seq_show+0x117/0x230
[22613.172970]  ? sysfs_kf_seq_show+0x117/0x230
[22613.173031]  __kasan_report+0x176/0x192
[22613.173064]  ? pr_cont_kernfs_name+0x40/0x60
[22613.173067]  ? sysfs_kf_seq_show+0x117/0x230
[22613.173070]  kasan_report+0xe/0x20
[22613.173072]  sysfs_kf_seq_show+0x117/0x230
[22613.173105]  seq_read+0x199/0x6d0
[22613.173110]  vfs_read+0xa5/0x1a0
[22613.173113]  ksys_read+0x110/0x160
[22613.173115]  ? kernel_write+0xb0/0xb0
[22613.173177]  do_syscall_64+0x77/0x290
[22613.173238]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[22613.173241] RIP: 0033:0x7fc2c886ac61
[22613.173244] Code: fe ff ff 48 8d 3d c7 a0 09 00 48 83 ec 08 e8 46 03 02 00 66 0f 1f 44 00 00 8b 05 ca fb 2c 00 48 63 ff 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 55 53 48 89 d5 48 89
[22613.173245] RSP: 002b:00007ffebe776d68 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[22613.173248] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fc2c886ac61
[22613.173249] RDX: 0000000000020000 RSI: 00007fc2c8cca000 RDI: 0000000000000003
[22613.173250] RBP: 0000000000020000 R08: ffffffffffffffff R09: 0000000000000000
[22613.173251] R10: 000000000000038c R11: 0000000000000246 R12: 00007fc2c8cca000
[22613.173253] R13: 0000000000000003 R14: 00007fc2c8cca00f R15: 0000000000020000
[22613.173255] ==================================================================
[22613.173256] Disabling lock debugging due to kernel taint
[22613.173350] BUG: kernel NULL pointer dereference, address: 0000000000000000
[22613.178380] #PF: supervisor read access in kernel mode
[22613.180959] #PF: error_code(0x0000) - not-present page
[22613.183444] PGD 0 P4D 0
[22613.184867] Oops: 0000 [#1] SMP KASAN PTI
[22613.186797] CPU: 1 PID: 6753 Comm: cat Tainted: G    B             5.5.0-rc7-lp151.28.16-default+ #11
[22613.191253] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/29/2019
[22613.196706] RIP: 0010:sysfs_kf_seq_show+0x117/0x230
[22613.199097] Code: ff 48 8b 0b 48 8b 44 24 08 48 01 e9 eb a6 31 f6 48 89 cf ba 00 10 00 00 48 89 4c 24 10 e8 b1 e6 e9 ff 4c 89 ff e8 19 07 ea ff <49> 8b 07 48 85 c0 48 89 44 24 08 0f 84 91 00 00 00 49 8b 6d 00 48
[22613.208016] RSP: 0018:ffff8881d4f8fd78 EFLAGS: 00010246
[22613.210448] RAX: 0000000000000000 RBX: ffff8881eb99b180 RCX: ffffffff810d9ef6
[22613.213691] RDX: 0000000000000001 RSI: 0000000000000246 RDI: 0000000000000246
[22613.216893] RBP: 0000000000001000 R08: fffffbfff072ddcd R09: fffffbfff072ddcd
[22613.220075] R10: 0000000000000001 R11: fffffbfff072ddcc R12: ffff8881de5c0200
[22613.223256] R13: ffff8881ed175500 R14: ffff8881eb99b198 R15: 0000000000000000
[22613.226290] FS:  00007fc2c8d3d500(0000) GS:ffff8881f2a80000(0000) knlGS:0000000000000000
[22613.229637] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[22613.231993] CR2: 0000000000000000 CR3: 00000001ec89a004 CR4: 00000000003606e0
[22613.234909] Call Trace:
[22613.235931]  seq_read+0x199/0x6d0
[22613.237259]  vfs_read+0xa5/0x1a0
[22613.239229]  ksys_read+0x110/0x160
[22613.240590]  ? kernel_write+0xb0/0xb0
[22613.242040]  do_syscall_64+0x77/0x290
[22613.243625]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[22613.245450] RIP: 0033:0x7fc2c886ac61
[22613.246706] Code: fe ff ff 48 8d 3d c7 a0 09 00 48 83 ec 08 e8 46 03 02 00 66 0f 1f 44 00 00 8b 05 ca fb 2c 00 48 63 ff 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 55 53 48 89 d5 48 89
[22613.253296] RSP: 002b:00007ffebe776d68 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[22613.255835] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007fc2c886ac61
[22613.258472] RDX: 0000000000020000 RSI: 00007fc2c8cca000 RDI: 0000000000000003
[22613.260807] RBP: 0000000000020000 R08: ffffffffffffffff R09: 0000000000000000
[22613.263188] R10: 000000000000038c R11: 0000000000000246 R12: 00007fc2c8cca000
[22613.265598] R13: 0000000000000003 R14: 00007fc2c8cca00f R15: 0000000000020000
[22613.268729] Modules linked in: scsi_transport_iscsi af_packet iscsi_ibft iscsi_boot_sysfs vmw_vsock_vmci_transport vsock fuse bnep kvm_intel kvm irqbypass crc32_pclmul crc32c_intel ghash_clmulni_intel snd_ens1371 snd_ac97_codec ac97_bus bcache snd_pcm btusb btrtl btbcm btintel crc64 aesni_intel glue_helper crypto_simd vmw_balloon cryptd bluetooth snd_timer snd_rawmidi snd joydev pcspkr e1000 rfkill vmw_vmci soundcore ecdh_generic ecc gameport i2c_piix4 mptctl ac button hid_generic usbhid sr_mod cdrom ata_generic ehci_pci vmwgfx uhci_hcd drm_kms_helper syscopyarea serio_raw sysfillrect sysimgblt fb_sys_fops ttm ehci_hcd mptspi scsi_transport_spi mptscsih ata_piix mptbase ahci usbcore libahci drm sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua
[22613.292429] CR2: 0000000000000000
[22613.293563] ---[ end trace a074b26a8508f378 ]---
[22613.295138] RIP: 0010:sysfs_kf_seq_show+0x117/0x230
[22613.296769] Code: ff 48 8b 0b 48 8b 44 24 08 48 01 e9 eb a6 31 f6 48 89 cf ba 00 10 00 00 48 89 4c 24 10 e8 b1 e6 e9 ff 4c 89 ff e8 19 07 ea ff <49> 8b 07 48 85 c0 48 89 44 24 08 0f 84 91 00 00 00 49 8b 6d 00 48
[22613.303553] RSP: 0018:ffff8881d4f8fd78 EFLAGS: 00010246
[22613.305280] RAX: 0000000000000000 RBX: ffff8881eb99b180 RCX: ffffffff810d9ef6
[22613.307924] RDX: 0000000000000001 RSI: 0000000000000246 RDI: 0000000000000246
[22613.310272] RBP: 0000000000001000 R08: fffffbfff072ddcd R09: fffffbfff072ddcd
[22613.312685] R10: 0000000000000001 R11: fffffbfff072ddcc R12: ffff8881de5c0200
[22613.315076] R13: ffff8881ed175500 R14: ffff8881eb99b198 R15: 0000000000000000
[22613.318116] FS:  00007fc2c8d3d500(0000) GS:ffff8881f2a80000(0000) knlGS:0000000000000000
[22613.320743] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[22613.322628] CR2: 0000000000000000 CR3: 00000001ec89a004 CR4: 00000000003606e0

Here this patch fixes the following problem by explicity set all the 7
members to 0 in bch_cache_accounting_clear().

Reported-by: Сорокин Артем Сергеевич <a.sorokin@bank-hlynov.ru>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

reiserfs: prevent NULL pointer dereference in reiserfs_insert_item()

[ Upstream commit aacee5446a2a1aa35d0a49dab289552578657fb4 ]

The variable inode may be NULL in reiserfs_insert_item(), but there is
no check before accessing the member of inode.

Fix this by adding NULL pointer check before calling reiserfs_debug().

Link: http://lkml.kernel.org/r/79c5135d-ff25-1cc9-4e99-9f572b88cc00@huawei.com
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Cc: zhengbin <zhengbin13@huawei.com>
Cc: Hu Shiyuan <hushiyuan@huawei.com>
Cc: Feilong Lin <linfeilong@huawei.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

lib/scatterlist.c: adjust indentation in __sg_alloc_table

[ Upstream commit 4e456fee215677584cafa7f67298a76917e89c64 ]

Clang warns:

  ../lib/scatterlist.c:314:5: warning: misleading indentation; statement
  is not part of the previous 'if' [-Wmisleading-indentation]
                          return -ENOMEM;
                          ^
  ../lib/scatterlist.c:311:4: note: previous statement is here
                          if (prv)
                          ^
  1 warning generated.

This warning occurs because there is a space before the tab on this
line.  Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.

Link: http://lkml.kernel.org/r/20191218033606.11942-1-natechancellor@gmail.com
Link: https://github.com/ClangBuiltLinux/linux/issues/830
Fixes: edce6820a9fd ("scatterlist: prevent invalid free when alloc fails")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ocfs2: fix a NULL pointer dereference when call ocfs2_update_inode_fsync_trans()

[ Upstream commit 9f16ca48fc818a17de8be1f75d08e7f4addc4497 ]

I found a NULL pointer dereference in ocfs2_update_inode_fsync_trans(),
handle->h_transaction may be NULL in this situation:

ocfs2_file_write_iter
  ->__generic_file_write_iter
      ->generic_perform_write
        ->ocfs2_write_begin
          ->ocfs2_write_begin_nolock
            ->ocfs2_write_cluster_by_desc
              ->ocfs2_write_cluster
                ->ocfs2_mark_extent_written
                  ->ocfs2_change_extent_flag
                    ->ocfs2_split_extent
                      ->ocfs2_try_to_merge_extent
                        ->ocfs2_extend_rotate_transaction
                          ->ocfs2_extend_trans
                            ->jbd2_journal_restart
                              ->jbd2__journal_restart
                                // handle->h_transaction is NULL here
                                ->handle->h_transaction = NULL;
                                ->start_this_handle
                                  /* journal aborted due to storage
                                     network disconnection, return error */
                                  ->return -EROFS;
                         /* line 3806 in ocfs2_try_to_merge_extent (),
                            it will ignore ret error. */
                        ->ret = 0;
        ->...
        ->ocfs2_write_end
          ->ocfs2_write_end_nolock
            ->ocfs2_update_inode_fsync_trans
              // NULL pointer dereference
              ->oi->i_sync_tid = handle->h_transaction->t_tid;

The information of NULL pointer dereference as follows:
    JBD2: Detected IO errors while flushing file data on dm-11-45
    Aborting journal on device dm-11-45.
    JBD2: Error -5 detected when updating journal superblock for dm-11-45.
    (dd,22081,3):ocfs2_extend_trans:474 ERROR: status = -30
    (dd,22081,3):ocfs2_try_to_merge_extent:3877 ERROR: status = -30
    Unable to handle kernel NULL pointer dereference at
    virtual address 0000000000000008
    Mem abort info:
      ESR = 0x96000004
      Exception class = DABT (current EL), IL = 32 bits
      SET = 0, FnV = 0
      EA = 0, S1PTW = 0
    Data abort info:
      ISV = 0, ISS = 0x00000004
      CM = 0, WnR = 0
    user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000e74e1338
    [0000000000000008] pgd=0000000000000000
    Internal error: Oops: 96000004 [#1] SMP
    Process dd (pid: 22081, stack limit = 0x00000000584f35a9)
    CPU: 3 PID: 22081 Comm: dd Kdump: loaded
    Hardware name: Huawei TaiShan 2280 V2/BC82AMDD, BIOS 0.98 08/25/2019
    pstate: 60400009 (nZCv daif +PAN -UAO)
    pc : ocfs2_write_end_nolock+0x2b8/0x550 [ocfs2]
    lr : ocfs2_write_end_nolock+0x2a0/0x550 [ocfs2]
    sp : ffff0000459fba70
    x29: ffff0000459fba70 x28: 0000000000000000
    x27: ffff807ccf7f1000 x26: 0000000000000001
    x25: ffff807bdff57970 x24: ffff807caf1d4000
    x23: ffff807cc79e9000 x22: 0000000000001000
    x21: 000000006c6cd000 x20: ffff0000091d9000
    x19: ffff807ccb239db0 x18: ffffffffffffffff
    x17: 000000000000000e x16: 0000000000000007
    x15: ffff807c5e15bd78 x14: 0000000000000000
    x13: 0000000000000000 x12: 0000000000000000
    x11: 0000000000000000 x10: 0000000000000001
    x9 : 0000000000000228 x8 : 000000000000000c
    x7 : 0000000000000fff x6 : ffff807a308ed6b0
    x5 : ffff7e01f10967c0 x4 : 0000000000000018
    x3 : d0bc661572445600 x2 : 0000000000000000
    x1 : 000000001b2e0200 x0 : 0000000000000000
    Call trace:
     ocfs2_write_end_nolock+0x2b8/0x550 [ocfs2]
     ocfs2_write_end+0x4c/0x80 [ocfs2]
     generic_perform_write+0x108/0x1a8
     __generic_file_write_iter+0x158/0x1c8
     ocfs2_file_write_iter+0x668/0x950 [ocfs2]
     __vfs_write+0x11c/0x190
     vfs_write+0xac/0x1c0
     ksys_write+0x6c/0xd8
     __arm64_sys_write+0x24/0x30
     el0_svc_common+0x78/0x130
     el0_svc_handler+0x38/0x78
     el0_svc+0x8/0xc

To prevent NULL pointer dereference in this situation, we use
is_handle_aborted() before using handle->h_transaction->t_tid.

Link: http://lkml.kernel.org/r/03e750ab-9ade-83aa-b000-b9e81e34e539@huawei.com
Signed-off-by: Yan Wang <wangyan122@huawei.com>
Reviewed-by: Jun Piao <piaojun@huawei.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ocfs2: make local header paths relative to C files

[ Upstream commit ca322fb6030956c2337fbf1c1beeb08c5dd5c943 ]

Gang He reports the failure of building fs/ocfs2/ as an external module
of the kernel installed on the system:

 $ cd fs/ocfs2
 $ make -C /lib/modules/`uname -r`/build M=`pwd` modules

If you want to make it work reliably, I'd recommend to remove ccflags-y
from the Makefiles, and to make header paths relative to the C files.  I
think this is the correct usage of the #include "..." directive.

Link: http://lkml.kernel.org/r/20191227022950.14804-1-ghe@suse.com
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Gang He <ghe@suse.com>
Reported-by: Gang He <ghe@suse.com>
Reviewed-by: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: do not do delalloc reservation under page lock

[ Upstream commit f4b1363cae43fef7c86c993b7ca7fe7d546b3c68 ]

We ran into a deadlock in production with the fixup worker.  The stack
traces were as follows:

Thread responsible for the writeout, waiting on the page lock

  [<0>] io_schedule+0x12/0x40
  [<0>] __lock_page+0x109/0x1e0
  [<0>] extent_write_cache_pages+0x206/0x360
  [<0>] extent_writepages+0x40/0x60
  [<0>] do_writepages+0x31/0xb0
  [<0>] __writeback_single_inode+0x3d/0x350
  [<0>] writeback_sb_inodes+0x19d/0x3c0
  [<0>] __writeback_inodes_wb+0x5d/0xb0
  [<0>] wb_writeback+0x231/0x2c0
  [<0>] wb_workfn+0x308/0x3c0
  [<0>] process_one_work+0x1e0/0x390
  [<0>] worker_thread+0x2b/0x3c0
  [<0>] kthread+0x113/0x130
  [<0>] ret_from_fork+0x35/0x40
  [<0>] 0xffffffffffffffff

Thread of the fixup worker who is holding the page lock

  [<0>] start_delalloc_inodes+0x241/0x2d0
  [<0>] btrfs_start_delalloc_roots+0x179/0x230
  [<0>] btrfs_alloc_data_chunk_ondemand+0x11b/0x2e0
  [<0>] btrfs_check_data_free_space+0x53/0xa0
  [<0>] btrfs_delalloc_reserve_space+0x20/0x70
  [<0>] btrfs_writepage_fixup_worker+0x1fc/0x2a0
  [<0>] normal_work_helper+0x11c/0x360
  [<0>] process_one_work+0x1e0/0x390
  [<0>] worker_thread+0x2b/0x3c0
  [<0>] kthread+0x113/0x130
  [<0>] ret_from_fork+0x35/0x40
  [<0>] 0xffffffffffffffff

Thankfully the stars have to align just right to hit this.  First you
have to end up in the fixup worker, which is tricky by itself (my
reproducer does DIO reads into a MMAP'ed region, so not a common
operation).  Then you have to have less than a page size of free data
space and 0 unallocated space so you go down the "commit the transaction
to free up pinned space" path.  This was accomplished by a random
balance that was running on the host.  Then you get this deadlock.

I'm still in the process of trying to force the deadlock to happen on
demand, but I've hit other issues.  I can still trigger the fixup worker
path itself so this patch has been tested in that regard, so the normal
case is fine.

Fixes: 87826df0ec36 ("btrfs: delalloc for page dirtied out-of-band in fixup worker")
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc: Do not consider weak unresolved symbol relocations as bad

[ Upstream commit 43e76cd368fbb67e767da5363ffeaa3989993c8c ]

Commit 8580ac9404f6 ("bpf: Process in-kernel BTF") introduced two weak
symbols that may be unresolved at link time which result in an absolute
relocation to 0. relocs_check.sh emits the following warning:

"WARNING: 2 bad relocations
c000000001a41478 R_PPC64_ADDR64    _binary__btf_vmlinux_bin_start
c000000001a41480 R_PPC64_ADDR64    _binary__btf_vmlinux_bin_end"

whereas those relocations are legitimate even for a relocatable kernel
compiled with -pie option.

relocs_check.sh already excluded some weak unresolved symbols explicitly:
remove those hardcoded symbols and add some logic that parses the symbols
using nm, retrieves all the weak unresolved symbols and excludes those from
the list of the potential bad relocations.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200118170335.21440-1-alex@ghiti.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

radeon: insert 10ms sleep in dce5_crtc_load_lut

[ Upstream commit ec3d65082d7dabad6fa8f66a8ef166f2d522d6b2 ]

Per at least one tester this is enough magic to recover the regression
introduced for some people (but not all) in

commit b8e2b0199cc377617dc238f5106352c06dcd3fa2
Author: Peter Rosin <peda@axentia.se>
Date:   Tue Jul 4 12:36:57 2017 +0200

    drm/fb-helper: factor out pseudo-palette

which for radeon had the side-effect of refactoring out a seemingly
redudant writing of the color palette.

10ms in a fairly slow modeset path feels like an acceptable form of
duct-tape, so maybe worth a shot and see what sticks.

Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=198123
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

trigger_next should increase position index

[ Upstream commit 6722b23e7a2ace078344064a9735fb73e554e9ef ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

Without patch:
 # dd bs=30 skip=1 if=/sys/kernel/tracing/events/sched/sched_switch/trigger
 dd: /sys/kernel/tracing/events/sched/sched_switch/trigger: cannot skip to specified offset
 n traceoff snapshot stacktrace enable_event disable_event enable_hist disable_hist hist
 # Available triggers:
 # traceon traceoff snapshot stacktrace enable_event disable_event enable_hist disable_hist hist
 6+1 records in
 6+1 records out
 206 bytes copied, 0.00027916 s, 738 kB/s

Notice the printing of "# Available triggers:..." after the line.

With the patch:
 # dd bs=30 skip=1 if=/sys/kernel/tracing/events/sched/sched_switch/trigger
 dd: /sys/kernel/tracing/events/sched/sched_switch/trigger: cannot skip to specified offset
 n traceoff snapshot stacktrace enable_event disable_event enable_hist disable_hist hist
 2+1 records in
 2+1 records out
 88 bytes copied, 0.000526867 s, 167 kB/s

It only prints the end of the file, and does not restart.

Link: http://lkml.kernel.org/r/3c35ee24-dd3a-8119-9c19-552ed253388a@virtuozzo.com
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ftrace: fpid_next() should increase position index

[ Upstream commit e4075e8bdffd93a9b6d6e1d52fabedceeca5a91b ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

Without patch:
 # dd bs=4 skip=1 if=/sys/kernel/tracing/set_ftrace_pid
 dd: /sys/kernel/tracing/set_ftrace_pid: cannot skip to specified offset
 id
 no pid
 2+1 records in
 2+1 records out
 10 bytes copied, 0.000213285 s, 46.9 kB/s

Notice the "id" followed by "no pid".

With the patch:
 # dd bs=4 skip=1 if=/sys/kernel/tracing/set_ftrace_pid
 dd: /sys/kernel/tracing/set_ftrace_pid: cannot skip to specified offset
 id
 0+1 records in
 0+1 records out
 3 bytes copied, 0.000202112 s, 14.8 kB/s

Notice that it only prints "id" and not the "no pid" afterward.

Link: http://lkml.kernel.org/r/4f87c6ad-f114-30bb-8506-c32274ce2992@virtuozzo.com
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

char: hpet: Fix out-of-bounds read bug

[ Upstream commit 98c49f1746ac44ccc164e914b9a44183fad09f51 ]

Currently, there is an out-of-bounds read on array hpetp->hp_dev
in the following for loop:

870         for (i = 0; i < hdp->hd_nirqs; i++)
871                 hpetp->hp_dev[i].hd_hdwirq = hdp->hd_irq[i];

This is due to the recent change from one-element array to
flexible-array member in struct hpets:

104 struct hpets {
...
113         struct hpet_dev hp_dev[];
114 };

This change affected the total size of the dynamic memory
allocation, decreasing it by one time the size of struct hpet_dev.

Fix this by adjusting the allocation size when calling
struct_size().

Fixes: 987f028b8637c ("char: hpet: Use flexible-array member")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Eric Biggers <ebiggers@kernel.org>
Link: https://lore.kernel.org/r/20200129022613.GA24281@embeddedor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/nouveau/disp/nv50-: prevent oops when no channel method map provided

[ Upstream commit 0e6176c6d286316e9431b4f695940cfac4ffe6c2 ]

The implementations for most channel types contains a map of methods to
priv registers in order to provide debugging info when a disp exception
has been raised.

This info is missing from the implementation of PIO channels as they're
rather simplistic already, however, if an exception is raised by one of
them, we'd end up triggering a NULL-pointer deref.  Not ideal...

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206299
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

irqchip/gic-v3: Only provision redistributors that are enabled in ACPI

[ Upstream commit 926b5dfa6b8dc666ff398044af6906b156e1d949 ]

We currently allocate redistributor region structures for
individual redistributors when ACPI doesn't present us with
compact MMIO regions covering multiple redistributors.

It turns out that we allocate these structures even when
the redistributor is flagged as disabled by ACPI. It works
fine until someone actually tries to tarse one of these
structures, and access the corresponding MMIO region.

Instead, track the number of enabled redistributors, and
only allocate what is required. This makes sure that there
is no invalid data to misuse.

Signed-off-by: Marc Zyngier <maz@kernel.org>
Reported-by: Heyi Guo <guoheyi@huawei.com>
Tested-by: Heyi Guo <guoheyi@huawei.com>
Link: https://lore.kernel.org/r/20191216062745.63397-1-guoheyi@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: do not allocate display_mode_lib unnecessarily

[ Upstream commit bb67bfd2e7101bf2ac5327b0b7a847cd9fb9723f ]

This allocation isn't required and can fail when resuming from suspend.

Bug: https://gitlab.freedesktop.org/drm/amd/issues/1009
Signed-off-by: Dor Askayo <dor.askayo@gmail.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rbd: work around -Wuninitialized warning

[ Upstream commit a55e601b2f02df5db7070e9a37bd655c9c576a52 ]

gcc -O3 warns about a dummy variable that is passed
down into rbd_img_fill_nodata without being initialized:

drivers/block/rbd.c: In function 'rbd_img_fill_nodata':
drivers/block/rbd.c:2573:13: error: 'dummy' is used uninitialized in this function [-Werror=uninitialized]
  fctx->iter = *fctx->pos;

Since this is a dummy, I assume the warning is harmless, but
it's better to initialize it anyway and avoid the warning.

Fixes: mmtom ("init/Kconfig: enable -O3 for all arches")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: check availability of mds cluster on mount after wait timeout

[ Upstream commit 97820058fb2831a4b203981fa2566ceaaa396103 ]

If all the MDS daemons are down for some reason, then the first mount
attempt will fail with EIO after the mount request times out.  A mount
attempt will also fail with EIO if all of the MDS's are laggy.

This patch changes the code to return -EHOSTUNREACH in these situations
and adds a pr_info error message to help the admin determine the cause.

URL: https://tracker.ceph.com/issues/4386
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/mm: Don't log user reads to 0xffffffff

[ Upstream commit 0f9aee0cb9da7db7d96f63cfa2dc5e4f1bffeb87 ]

Running vdsotest leaves many times the following log:

  [   79.629901] vdsotest[396]: User access of kernel address (ffffffff) - exploit attempt? (uid: 0)

A pointer set to (-1) is likely a programming error similar to
a NULL pointer and is not worth logging as an exploit attempt.

Don't log user accesses to 0xffffffff.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0728849e826ba16f1fbd6fa7f5c6cc87bd64e097.1577087627.git.christophe.leroy@c-s.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: map_seq_next should always increase position index

[ Upstream commit 90435a7891a2259b0f74c5a1bc5600d0d64cba8f ]

If seq_file .next fuction does not change position index,
read after some lseek can generate an unexpected output.

See also: https://bugzilla.kernel.org/show_bug.cgi?id=206283

v1 -> v2: removed missed increment in end of function

Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/eca84fdd-c374-a154-d874-6c7b55fc3bc4@virtuozzo.com
Signed-off-by: Sasha Levin <sashal@kernel.org>