Soenke Huster [Wed, 12 Oct 2022 07:45:06 +0000 (09:45 +0200)]
Bluetooth: virtio_bt: Use skb_put to set length
[ Upstream commit
160fbcf3bfb93c3c086427f9f4c8bc70f217e9be ]
By using skb_put we ensure that skb->tail is set
correctly. Currently, skb->tail is always zero, which
leads to errors, such as the following page fault in
rfcomm_recv_frame:
BUG: unable to handle page fault for address:
ffffed1021de29ff
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
RIP: 0010:rfcomm_run+0x831/0x4040 (net/bluetooth/rfcomm/core.c:1751)
Fixes:
afd2daa26c7a ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Maxim Mikityanskiy [Tue, 4 Oct 2022 21:27:18 +0000 (00:27 +0300)]
Bluetooth: L2CAP: Fix use-after-free caused by l2cap_reassemble_sdu
[ Upstream commit
3aff8aaca4e36dc8b17eaa011684881a80238966 ]
Fix the race condition between the following two flows that run in
parallel:
1. l2cap_reassemble_sdu -> chan->ops->recv (l2cap_sock_recv_cb) ->
__sock_queue_rcv_skb.
2. bt_sock_recvmsg -> skb_recv_datagram, skb_free_datagram.
An SKB can be queued by the first flow and immediately dequeued and
freed by the second flow, therefore the callers of l2cap_reassemble_sdu
can't use the SKB after that function returns. However, some places
continue accessing struct l2cap_ctrl that resides in the SKB's CB for a
short time after l2cap_reassemble_sdu returns, leading to a
use-after-free condition (the stack trace is below, line numbers for
kernel 5.19.8).
Fix it by keeping a local copy of struct l2cap_ctrl.
BUG: KASAN: use-after-free in l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
Read of size 1 at addr
ffff88812025f2f0 by task kworker/u17:3/43169
Workqueue: hci0 hci_rx_work [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4))
print_report.cold (mm/kasan/report.c:314 mm/kasan/report.c:429)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
kasan_report (mm/kasan/report.c:162 mm/kasan/report.c:493)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx (net/bluetooth/l2cap_core.c:7236 net/bluetooth/l2cap_core.c:7271) bluetooth
ret_from_fork (arch/x86/entry/entry_64.S:306)
</TASK>
Allocated by task 43169:
kasan_save_stack (mm/kasan/common.c:39)
__kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
kmem_cache_alloc_node (mm/slab.h:750 mm/slub.c:3243 mm/slub.c:3293)
__alloc_skb (net/core/skbuff.c:414)
l2cap_recv_frag (./include/net/bluetooth/bluetooth.h:425 net/bluetooth/l2cap_core.c:8329) bluetooth
l2cap_recv_acldata (net/bluetooth/l2cap_core.c:8442) bluetooth
hci_rx_work (net/bluetooth/hci_core.c:3642 net/bluetooth/hci_core.c:3832) bluetooth
process_one_work (kernel/workqueue.c:2289)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2437)
kthread (kernel/kthread.c:376)
ret_from_fork (arch/x86/entry/entry_64.S:306)
Freed by task 27920:
kasan_save_stack (mm/kasan/common.c:39)
kasan_set_track (mm/kasan/common.c:45)
kasan_set_free_info (mm/kasan/generic.c:372)
____kasan_slab_free (mm/kasan/common.c:368 mm/kasan/common.c:328)
slab_free_freelist_hook (mm/slub.c:1780)
kmem_cache_free (mm/slub.c:3536 mm/slub.c:3553)
skb_free_datagram (./include/net/sock.h:1578 ./include/net/sock.h:1639 net/core/datagram.c:323)
bt_sock_recvmsg (net/bluetooth/af_bluetooth.c:295) bluetooth
l2cap_sock_recvmsg (net/bluetooth/l2cap_sock.c:1212) bluetooth
sock_read_iter (net/socket.c:1087)
new_sync_read (./include/linux/fs.h:2052 fs/read_write.c:401)
vfs_read (fs/read_write.c:482)
ksys_read (fs/read_write.c:620)
do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120)
Link: https://lore.kernel.org/linux-bluetooth/CAKErNvoqga1WcmoR3-0875esY6TVWFQDandbVZncSiuGPBQXLA@mail.gmail.com/T/#u
Fixes:
d2a7ac5d5d3a ("Bluetooth: Add the ERTM receive state machine")
Fixes:
4b51dae96731 ("Bluetooth: Add streaming mode receive and incoming packet classifier")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jozsef Kadlecsik [Wed, 2 Nov 2022 09:40:47 +0000 (10:40 +0100)]
netfilter: ipset: enforce documented limit to prevent allocating huge memory
[ Upstream commit
510841da1fcc16f702440ab58ef0b4d82a9056b7 ]
Daniel Xu reported that the hash:net,iface type of the ipset subsystem does
not limit adding the same network with different interfaces to a set, which
can lead to huge memory usage or allocation failure.
The quick reproducer is
$ ipset create ACL.IN.ALL_PERMIT hash:net,iface hashsize 1048576 timeout 0
$ for i in $(seq 0 100); do /sbin/ipset add ACL.IN.ALL_PERMIT 0.0.0.0/0,kaf_$i timeout 0 -exist; done
The backtrace when vmalloc fails:
[Tue Oct 25 00:13:08 2022] ipset: vmalloc error: size
1073741848, exceeds total pages
<...>
[Tue Oct 25 00:13:08 2022] Call Trace:
[Tue Oct 25 00:13:08 2022] <TASK>
[Tue Oct 25 00:13:08 2022] dump_stack_lvl+0x48/0x60
[Tue Oct 25 00:13:08 2022] warn_alloc+0x155/0x180
[Tue Oct 25 00:13:08 2022] __vmalloc_node_range+0x72a/0x760
[Tue Oct 25 00:13:08 2022] ? hash_netiface4_add+0x7c0/0xb20
[Tue Oct 25 00:13:08 2022] ? __kmalloc_large_node+0x4a/0x90
[Tue Oct 25 00:13:08 2022] kvmalloc_node+0xa6/0xd0
[Tue Oct 25 00:13:08 2022] ? hash_netiface4_resize+0x99/0x710
<...>
The fix is to enforce the limit documented in the ipset(8) manpage:
> The internal restriction of the hash:net,iface set type is that the same
> network prefix cannot be stored with more than 64 different interfaces
> in a single set.
Fixes:
ccf0a4b7fc68 ("netfilter: ipset: Add bucketsize parameter to all hash types")
Reported-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Filipe Manana [Tue, 1 Nov 2022 16:15:39 +0000 (16:15 +0000)]
btrfs: fix ulist leaks in error paths of qgroup self tests
[ Upstream commit
d37de92b38932d40e4a251e876cc388f9aee5f42 ]
In the test_no_shared_qgroup() and test_multiple_refs() qgroup self tests,
if we fail to add the tree ref, remove the extent item or remove the
extent ref, we are returning from the test function without freeing the
"old_roots" ulist that was allocated by the previous calls to
btrfs_find_all_roots(). Fix that by calling ulist_free() before returning.
Fixes:
442244c96332 ("btrfs: qgroup: Switch self test to extent-oriented qgroup mechanism.")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Filipe Manana [Tue, 1 Nov 2022 16:15:38 +0000 (16:15 +0000)]
btrfs: fix inode list leak during backref walking at find_parent_nodes()
[ Upstream commit
92876eec382a0f19f33d09d2c939e9ca49038ae5 ]
During backref walking, at find_parent_nodes(), if we are dealing with a
data extent and we get an error while resolving the indirect backrefs, at
resolve_indirect_refs(), or in the while loop that iterates over the refs
in the direct refs rbtree, we end up leaking the inode lists attached to
the direct refs we have in the direct refs rbtree that were not yet added
to the refs ulist passed as argument to find_parent_nodes(). Since they
were not yet added to the refs ulist and prelim_release() does not free
the lists, on error the caller can only free the lists attached to the
refs that were added to the refs ulist, all the remaining refs get their
inode lists never freed, therefore leaking their memory.
Fix this by having prelim_release() always free any attached inode list
to each ref found in the rbtree, and have find_parent_nodes() set the
ref's inode list to NULL once it transfers ownership of the inode list
to a ref added to the refs ulist passed to find_parent_nodes().
Fixes:
86d5f9944252 ("btrfs: convert prelimary reference tracking to use rbtrees")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Filipe Manana [Tue, 1 Nov 2022 16:15:37 +0000 (16:15 +0000)]
btrfs: fix inode list leak during backref walking at resolve_indirect_refs()
[ Upstream commit
5614dc3a47e3310fbc77ea3b67eaadd1c6417bf1 ]
During backref walking, at resolve_indirect_refs(), if we get an error
we jump to the 'out' label and call ulist_free() on the 'parents' ulist,
which frees all the elements in the ulist - however that does not free
any inode lists that may be attached to elements, through the 'aux' field
of a ulist node, so we end up leaking lists if we have any attached to
the unodes.
Fix this by calling free_leaf_list() instead of ulist_free() when we exit
from resolve_indirect_refs(). The static function free_leaf_list() is
moved up for this to be possible and it's slightly simplified by removing
unnecessary code.
Fixes:
3301958b7c1d ("Btrfs: add inodes before dropping the extent lock in find_all_leafs")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Mon, 31 Oct 2022 12:13:41 +0000 (20:13 +0800)]
isdn: mISDN: netjet: fix wrong check of device registration
[ Upstream commit
bf00f5426074249058a106a6edbb89e4b25a4d79 ]
The class is set in mISDN_register_device(), but if device_add() returns
error, it will lead to delete a device without added, fix this by using
device_is_registered() to check if the device is registered.
Fixes:
a900845e5661 ("mISDN: Add support for Traverse Technologies NETJet PCI cards")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Mon, 31 Oct 2022 12:13:40 +0000 (20:13 +0800)]
mISDN: fix possible memory leak in mISDN_register_device()
[ Upstream commit
e7d1d4d9ac0dfa40be4c2c8abd0731659869b297 ]
Afer commit
1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
add put_device() to give up the reference, so that the name can be
freed in kobject_cleanup() when the refcount is 0.
Set device class before put_device() to avoid null release() function
WARN message in device_release().
Fixes:
1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhang Qilong [Fri, 28 Oct 2022 16:10:49 +0000 (00:10 +0800)]
rose: Fix NULL pointer dereference in rose_send_frame()
[ Upstream commit
e97c089d7a49f67027395ddf70bf327eeac2611e ]
The syzkaller reported an issue:
KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387]
CPU: 0 PID: 4069 Comm: kworker/0:15 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Workqueue: rcu_gp srcu_invoke_callbacks
RIP: 0010:rose_send_frame+0x1dd/0x2f0 net/rose/rose_link.c:101
Call Trace:
<IRQ>
rose_transmit_clear_request+0x1d5/0x290 net/rose/rose_link.c:255
rose_rx_call_request+0x4c0/0x1bc0 net/rose/af_rose.c:1009
rose_loopback_timer+0x19e/0x590 net/rose/rose_loopback.c:111
call_timer_fn+0x1a0/0x6b0 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers.part.0+0x674/0xa80 kernel/time/timer.c:1790
__run_timers kernel/time/timer.c:1768 [inline]
run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1803
__do_softirq+0x1d0/0x9c8 kernel/softirq.c:571
[...]
</IRQ>
It triggers NULL pointer dereference when 'neigh->dev->dev_addr' is
called in the rose_send_frame(). It's the first occurrence of the
`neigh` is in rose_loopback_timer() as `rose_loopback_neigh', and
the 'dev' in 'rose_loopback_neigh' is initialized sa nullptr.
It had been fixed by commit
3b3fd068c56e3fbea30090859216a368398e39bf
("rose: Fix Null pointer dereference in rose_send_frame()") ever.
But it's introduced by commit
3c53cd65dece47dd1f9d3a809f32e59d1d87b2b8
("rose: check NULL rose_loopback_neigh->loopback") again.
We fix it by add NULL check in rose_transmit_clear_request(). When
the 'dev' in 'neigh' is NULL, we don't reply the request and just
clear it.
syzkaller don't provide repro, and I provide a syz repro like:
r0 = syz_init_net_socket$bt_sco(0x1f, 0x5, 0x2)
ioctl$sock_inet_SIOCSIFFLAGS(r0, 0x8914, &(0x7f0000000180)={'rose0\x00', 0x201})
r1 = syz_init_net_socket$rose(0xb, 0x5, 0x0)
bind$rose(r1, &(0x7f00000000c0)=@full={0xb, @dev, @null, 0x0, [@null, @null, @netrom, @netrom, @default, @null]}, 0x40)
connect$rose(r1, &(0x7f0000000240)=@short={0xb, @dev={0xbb, 0xbb, 0xbb, 0x1, 0x0}, @remote={0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0xcc, 0x1}, 0x1, @netrom={0xbb, 0xbb, 0xbb, 0xbb, 0xbb, 0x0, 0x0}}, 0x1c)
Fixes:
3c53cd65dece ("rose: check NULL rose_loopback_neigh->loopback")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhengchao Shao [Mon, 31 Oct 2022 12:07:05 +0000 (20:07 +0800)]
ipvs: fix WARNING in ip_vs_app_net_cleanup()
[ Upstream commit
5663ed63adb9619c98ab7479aa4606fa9b7a548c ]
During the initialization of ip_vs_app_net_init(), if file ip_vs_app
fails to be created, the initialization is successful by default.
Therefore, the ip_vs_app file doesn't be found during the remove in
ip_vs_app_net_cleanup(). It will cause WRNING.
The following is the stack information:
name 'ip_vs_app'
WARNING: CPU: 1 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
Call Trace:
<TASK>
ops_exit_list+0x125/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes:
457c4cbc5a3d ("[NET]: Make /proc/net per network namespace")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhengchao Shao [Mon, 31 Oct 2022 12:07:04 +0000 (20:07 +0800)]
ipvs: fix WARNING in __ip_vs_cleanup_batch()
[ Upstream commit
3d00c6a0da8ddcf75213e004765e4a42acc71d5d ]
During the initialization of ip_vs_conn_net_init(), if file ip_vs_conn
or ip_vs_conn_sync fails to be created, the initialization is successful
by default. Therefore, the ip_vs_conn or ip_vs_conn_sync file doesn't
be found during the remove.
The following is the stack information:
name 'ip_vs_conn_sync'
WARNING: CPU: 3 PID: 9 at fs/proc/generic.c:712
remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
Call Trace:
<TASK>
__ip_vs_cleanup_batch+0x7d/0x120
ops_exit_list+0x125/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes:
61b1ab4583e2 ("IPVS: netns, add basic init per netns.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jason A. Donenfeld [Wed, 26 Oct 2022 12:32:16 +0000 (14:32 +0200)]
ipvs: use explicitly signed chars
[ Upstream commit
5c26159c97b324dc5174a5713eafb8c855cf8106 ]
The `char` type with no explicit sign is sometimes signed and sometimes
unsigned. This code will break on platforms such as arm, where char is
unsigned. So mark it here as explicitly signed, so that the
todrop_counter decrement and subsequent comparison is correct.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pablo Neira Ayuso [Wed, 26 Oct 2022 07:54:45 +0000 (09:54 +0200)]
netfilter: nf_tables: release flow rule object from commit path
[ Upstream commit
26b5934ff4194e13196bedcba373cd4915071d0e ]
No need to postpone this to the commit release path, since no packets
are walking over this object, this is accessed from control plane only.
This helped uncovered UAF triggered by races with the netlink notifier.
Fixes:
9dd732e0bdf5 ("netfilter: nf_tables: memleak flow rule from commit path")
Reported-by: syzbot+8f747f62763bc6c32916@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pablo Neira Ayuso [Wed, 26 Oct 2022 07:52:36 +0000 (09:52 +0200)]
netfilter: nf_tables: netlink notifier might race to release objects
[ Upstream commit
d4bc8271db21ea9f1c86a1ca4d64999f184d4aae ]
commit release path is invoked via call_rcu and it runs lockless to
release the objects after rcu grace period. The netlink notifier handler
might win race to remove objects that the transaction context is still
referencing from the commit release path.
Call rcu_barrier() to ensure pending rcu callbacks run to completion
if the list of transactions to be destroyed is not empty.
Fixes:
6001a930ce03 ("netfilter: nftables: introduce table ownership")
Reported-by: syzbot+8f747f62763bc6c32916@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ziyang Xuan [Sat, 29 Oct 2022 09:41:01 +0000 (17:41 +0800)]
net: tun: fix bugs for oversize packet when napi frags enabled
[ Upstream commit
363a5328f4b0517e59572118ccfb7c626d81dca9 ]
Recently, we got two syzkaller problems because of oversize packet
when napi frags enabled.
One of the problems is because the first seg size of the iov_iter
from user space is very big, it is
2147479538 which is bigger than
the threshold value for bail out early in __alloc_pages(). And
skb->pfmemalloc is true, __kmalloc_reserve() would use pfmemalloc
reserves without __GFP_NOWARN flag. Thus we got a warning as following:
========================================================
WARNING: CPU: 1 PID: 17965 at mm/page_alloc.c:5295 __alloc_pages+0x1308/0x16c4 mm/page_alloc.c:5295
...
Call trace:
__alloc_pages+0x1308/0x16c4 mm/page_alloc.c:5295
__alloc_pages_node include/linux/gfp.h:550 [inline]
alloc_pages_node include/linux/gfp.h:564 [inline]
kmalloc_large_node+0x94/0x350 mm/slub.c:4038
__kmalloc_node_track_caller+0x620/0x8e4 mm/slub.c:4545
__kmalloc_reserve.constprop.0+0x1e4/0x2b0 net/core/skbuff.c:151
pskb_expand_head+0x130/0x8b0 net/core/skbuff.c:1654
__skb_grow include/linux/skbuff.h:2779 [inline]
tun_napi_alloc_frags+0x144/0x610 drivers/net/tun.c:1477
tun_get_user+0x31c/0x2010 drivers/net/tun.c:1835
tun_chr_write_iter+0x98/0x100 drivers/net/tun.c:2036
The other problem is because odd IPv6 packets without NEXTHDR_NONE
extension header and have big packet length, it is 2127925 which is
bigger than ETH_MAX_MTU(65535). After ipv6_gso_pull_exthdrs() in
ipv6_gro_receive(), network_header offset and transport_header offset
are all bigger than U16_MAX. That would trigger skb->network_header
and skb->transport_header overflow error, because they are all '__u16'
type. Eventually, it would affect the value for __skb_push(skb, value),
and make it be a big value. After __skb_push() in ipv6_gro_receive(),
skb->data would less than skb->head, an out of bounds memory bug occurred.
That would trigger the problem as following:
==================================================================
BUG: KASAN: use-after-free in eth_type_trans+0x100/0x260
...
Call trace:
dump_backtrace+0xd8/0x130
show_stack+0x1c/0x50
dump_stack_lvl+0x64/0x7c
print_address_description.constprop.0+0xbc/0x2e8
print_report+0x100/0x1e4
kasan_report+0x80/0x120
__asan_load8+0x78/0xa0
eth_type_trans+0x100/0x260
napi_gro_frags+0x164/0x550
tun_get_user+0xda4/0x1270
tun_chr_write_iter+0x74/0x130
do_iter_readv_writev+0x130/0x1ec
do_iter_write+0xbc/0x1e0
vfs_writev+0x13c/0x26c
To fix the problems, restrict the packet size less than
(ETH_MAX_MTU - NET_SKB_PAD - NET_IP_ALIGN) which has considered reserved
skb space in napi_alloc_skb() because transport_header is an offset from
skb->head. Add len check in tun_napi_alloc_frags() simply.
Fixes:
90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221029094101.1653855-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Carpenter [Fri, 28 Oct 2022 15:05:00 +0000 (18:05 +0300)]
net: sched: Fix use after free in red_enqueue()
[ Upstream commit
8bdc2acd420c6f3dd1f1c78750ec989f02a1e2b9 ]
We can't use "skb" again after passing it to qdisc_enqueue(). This is
basically identical to commit
2f09707d0c97 ("sch_sfb: Also store skb
len before calling child enqueue").
Fixes:
d7f4f332f082 ("sch_red: update backlog as well")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sergey Shtylyov [Fri, 28 Oct 2022 21:07:06 +0000 (00:07 +0300)]
ata: pata_legacy: fix pdc20230_set_piomode()
[ Upstream commit
171a93182eccd6e6835d2c86b40787f9f832efaa ]
Clang gives a warning when compiling pata_legacy.c with 'make W=1' about
the 'rt' local variable in pdc20230_set_piomode() being set but unused.
Quite obviously, there is an outb() call missing to write back the updated
variable. Moreover, checking the docs by Petr Soucek revealed that bitwise
AND should have been done with a negated timing mask and the master/slave
timing masks were swapped while updating...
Fixes:
669a5db411d8 ("[libata] Add a bunch of PATA drivers.")
Reported-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhang Changzhong [Fri, 28 Oct 2022 02:09:11 +0000 (10:09 +0800)]
net: fec: fix improper use of NETDEV_TX_BUSY
[ Upstream commit
06a4df5863f73af193a4ff7abf7cb04058584f06 ]
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fix it by returning NETDEV_TX_OK in case of dma_map_single() fails.
Fixes:
79f339125ea3 ("net: fec: Add software TSO support")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:32 +0000 (22:03 +0800)]
nfc: nfcmrvl: Fix potential memory leak in nfcmrvl_i2c_nci_send()
[ Upstream commit
93d904a734a74c54d945a9884b4962977f1176cd ]
nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb
should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send()
will only free skb when i2c_master_send() return >=0, which means skb
will memleak when i2c_master_send() failed. Free skb no matter whether
i2c_master_send() succeeds.
Fixes:
b5b3e23e4cac ("NFC: nfcmrvl: add i2c driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:31 +0000 (22:03 +0800)]
nfc: s3fwrn5: Fix potential memory leak in s3fwrn5_nci_send()
[ Upstream commit
3a146b7e3099dc7cf3114f627d9b79291e2d2203 ]
s3fwrn5_nci_send() will call s3fwrn5_i2c_write() or s3fwrn82_uart_write(),
and free the skb if write() failed. However, even if the write() run
succeeds, the skb will not be freed in write(). As the result, the skb
will memleak. s3fwrn5_nci_send() should also free the skb when write()
succeeds.
Fixes:
c04c674fadeb ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:30 +0000 (22:03 +0800)]
nfc: nxp-nci: Fix potential memory leak in nxp_nci_send()
[ Upstream commit
7bf1ed6aff0f70434bd0cdd45495e83f1dffb551 ]
nxp_nci_send() will call nxp_nci_i2c_write(), and only free skb when
nxp_nci_i2c_write() failed. However, even if the nxp_nci_i2c_write()
run succeeds, the skb will not be freed in nxp_nci_i2c_write(). As the
result, the skb will memleak. nxp_nci_send() should also free the skb
when nxp_nci_i2c_write() succeeds.
Fixes:
dece45855a8b ("NFC: nxp-nci: Add support for NXP NCI chips")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shang XiaoJing [Thu, 27 Oct 2022 14:03:29 +0000 (22:03 +0800)]
nfc: fdp: Fix potential memory leak in fdp_nci_send()
[ Upstream commit
8e4aae6b8ca76afb1fb64dcb24be44ba814e7f8a ]
fdp_nci_send() will call fdp_nci_i2c_write that will not free skb in
the function. As a result, when fdp_nci_i2c_write() finished, the skb
will memleak. fdp_nci_send() should free skb after fdp_nci_i2c_write()
finished.
Fixes:
a06347c04c13 ("NFC: Add Intel Fields Peak NFC solution driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vladimir Oltean [Thu, 27 Oct 2022 14:54:39 +0000 (17:54 +0300)]
net: dsa: fall back to default tagger if we can't load the one from DT
[ Upstream commit
a2c65a9d0568b6737c02b54f00b80716a53fac61 ]
DSA tagging protocol drivers can be changed at runtime through sysfs and
at probe time through the device tree (support for the latter was added
later).
When changing through sysfs, it is assumed that the module for the new
tagging protocol was already loaded into the kernel (in fact this is
only a concern for Ocelot/Felix switches, where we have tag_ocelot.ko
and tag_ocelot_8021q.ko; for every other switch, the default and
alternative protocols are compiled within the same .ko, so there is
nothing for the user to load).
The kernel cannot currently call request_module(), because it has no way
of constructing the modalias name of the tagging protocol driver
("dsa_tag-%d", where the number is one of DSA_TAG_PROTO_*_VALUE).
The device tree only contains the string name of the tagging protocol
("ocelot-8021q"), and the only mapping between the string and the
DSA_TAG_PROTO_OCELOT_8021Q_VALUE is present in tag_ocelot_8021q.ko.
So this is a chicken-and-egg situation and dsa_core.ko has nothing based
on which it can automatically request the insertion of the module.
As a consequence, if CONFIG_NET_DSA_TAG_OCELOT_8021Q is built as module,
the switch will forever defer probing.
The long-term solution is to make DSA call request_module() somehow,
but that probably needs some refactoring.
What we can do to keep operating with existing device tree blobs is to
cancel the attempt to change the tagging protocol with the one specified
there, and to remain operating with the default one. Depending on the
situation, the default protocol might still allow some functionality
(in the case of ocelot, it does), and it's better to have that than to
fail to probe.
Fixes:
deff710703d8 ("net: dsa: Allow default tag protocol to be overridden from DT")
Link: https://lore.kernel.org/lkml/20221027113248.420216-1-michael@walle.cc/
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027145439.3086017-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Carpenter [Tue, 25 Oct 2022 15:32:32 +0000 (18:32 +0300)]
RDMA/qedr: clean up work queue on failure in qedr_alloc_resources()
[ Upstream commit
7a47e077e503feb73d56e491ce89aa73b67a3972 ]
Add a check for if create_singlethread_workqueue() fails and also destroy
the work queue on failure paths.
Fixes:
e411e0587e0d ("RDMA/qedr: Add iWARP connection management functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Y1gBkDucQhhWj5YM@kili
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chen Zhongjin [Tue, 25 Oct 2022 02:41:46 +0000 (10:41 +0800)]
RDMA/core: Fix null-ptr-deref in ib_core_cleanup()
[ Upstream commit
07c0d131cc0fe1f3981a42958fc52d573d303d89 ]
KASAN reported a null-ptr-deref error:
KASAN: null-ptr-deref in range [0x0000000000000118-0x000000000000011f]
CPU: 1 PID: 379
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:destroy_workqueue+0x2f/0x740
RSP: 0018:
ffff888016137df8 EFLAGS:
00000202
...
Call Trace:
ib_core_cleanup+0xa/0xa1 [ib_core]
__do_sys_delete_module.constprop.0+0x34f/0x5b0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fa1a0d221b7
...
It is because the fail of roce_gid_mgmt_init() is ignored:
ib_core_init()
roce_gid_mgmt_init()
gid_cache_wq = alloc_ordered_workqueue # fail
...
ib_core_cleanup()
roce_gid_mgmt_cleanup()
destroy_workqueue(gid_cache_wq)
# destroy an unallocated wq
Fix this by catching the fail of roce_gid_mgmt_init() in ib_core_init().
Fixes:
03db3a2d81e6 ("IB/core: Add RoCE GID table management")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221025024146.109137-1-chenzhongjin@huawei.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chen Zhongjin [Wed, 26 Oct 2022 02:03:21 +0000 (10:03 +0800)]
net: dsa: Fix possible memory leaks in dsa_loop_init()
[ Upstream commit
633efc8b3dc96f56f5a57f2a49764853a2fa3f50 ]
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies
4295040478 (age 238.976s)
backtrace:
[<
000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<
00000000a9c44622>] phy_device_create+0x5d/0x970
[<
00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<
00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<
000000008a834798>] fixed_phy_register+0x84/0xb0
[<
0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes:
98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhang Xiaoxu [Thu, 20 Oct 2022 03:20:54 +0000 (11:20 +0800)]
nfs4: Fix kmemleak when allocate slot failed
[ Upstream commit
7e8436728e22181c3f12a5dbabd35ed3a8b8c593 ]
If one of the slot allocate failed, should cleanup all the other
allocated slots, otherwise, the allocated slots will leak:
unreferenced object 0xffff8881115aa100 (size 64):
comm ""mount.nfs"", pid 679, jiffies
4294744957 (age 115.037s)
hex dump (first 32 bytes):
00 cc 19 73 81 88 ff ff 00 a0 5a 11 81 88 ff ff ...s......Z.....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
000000007a4c434a>] nfs4_find_or_create_slot+0x8e/0x130
[<
000000005472a39c>] nfs4_realloc_slot_table+0x23f/0x270
[<
00000000cd8ca0eb>] nfs40_init_client+0x4a/0x90
[<
00000000128486db>] nfs4_init_client+0xce/0x270
[<
000000008d2cacad>] nfs4_set_client+0x1a2/0x2b0
[<
000000000e593b52>] nfs4_create_server+0x300/0x5f0
[<
00000000e4425dd2>] nfs4_try_get_tree+0x65/0x110
[<
00000000d3a6176f>] vfs_get_tree+0x41/0xf0
[<
0000000016b5ad4c>] path_mount+0x9b3/0xdd0
[<
00000000494cae71>] __x64_sys_mount+0x190/0x1d0
[<
000000005d56bdec>] do_syscall_64+0x35/0x80
[<
00000000687c9ae4>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes:
abf79bb341bf ("NFS: Add a slot table to struct nfs_client for NFSv4.0 transport blocking")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Benjamin Coddington [Thu, 13 Oct 2022 15:58:01 +0000 (11:58 -0400)]
NFSv4.2: Fixup CLONE dest file size for zero-length count
[ Upstream commit
038efb6348ce96228f6828354cb809c22a661681 ]
When holding a delegation, the NFS client optimizes away setting the
attributes of a file from the GETATTR in the compound after CLONE, and for
a zero-length CLONE we will end up setting the inode's size to zero in
nfs42_copy_dest_done(). Handle this case by computing the resulting count
from the server's reported size after CLONE's GETATTR.
Suggested-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes:
94d202d5ca39 ("NFSv42: Copy offload should update the file size when appropriate")
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhang Xiaoxu [Thu, 20 Oct 2022 03:42:17 +0000 (11:42 +0800)]
SUNRPC: Fix null-ptr-deref when xps sysfs alloc failed
[ Upstream commit
cbdeaee94a415800c65a8c3fa04d9664a8b8fb3a ]
There is a null-ptr-deref when xps sysfs alloc failed:
BUG: KASAN: null-ptr-deref in sysfs_do_create_link_sd+0x40/0xd0
Read of size 8 at addr
0000000000000030 by task gssproxy/457
CPU: 5 PID: 457 Comm: gssproxy Not tainted 6.0.0-09040-g02357b27ee03 #9
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
kasan_report+0xa3/0x120
sysfs_do_create_link_sd+0x40/0xd0
rpc_sysfs_client_setup+0x161/0x1b0
rpc_new_client+0x3fc/0x6e0
rpc_create_xprt+0x71/0x220
rpc_create+0x1d4/0x350
gssp_rpc_create+0xc3/0x160
set_gssp_clnt+0xbc/0x140
write_gssp+0x116/0x1a0
proc_reg_write+0xd6/0x130
vfs_write+0x177/0x690
ksys_write+0xb9/0x150
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
When the xprt_switch sysfs alloc failed, should not add xprt and
switch sysfs to it, otherwise, maybe null-ptr-deref; also initialize
the 'xps_sysfs' to NULL to avoid oops when destroy it.
Fixes:
2a338a543163 ("sunrpc: add a symlink from rpc-client directory to the xprt_switch")
Fixes:
d408ebe04ac5 ("sunrpc: add add sysfs directory per xprt under each xprt_switch")
Fixes:
baea99445dd4 ("sunrpc: add xprt_switch direcotry to sunrpc's sysfs")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Trond Myklebust [Sun, 16 Oct 2022 18:44:33 +0000 (14:44 -0400)]
NFSv4.1: We must always send RECLAIM_COMPLETE after a reboot
[ Upstream commit
e59679f2b7e522ecad99974e5636291ffd47c184 ]
Currently, we are only guaranteed to send RECLAIM_COMPLETE if we have
open state to recover. Fix the client to always send RECLAIM_COMPLETE
after setting up the lease.
Fixes:
fce5c838e133 ("nfs41: RECLAIM_COMPLETE functionality")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Trond Myklebust [Sun, 16 Oct 2022 18:44:32 +0000 (14:44 -0400)]
NFSv4.1: Handle RECLAIM_COMPLETE trunking errors
[ Upstream commit
5d917cba3201e5c25059df96c29252fd99c4f6a7 ]
If RECLAIM_COMPLETE sets the NFS4CLNT_BIND_CONN_TO_SESSION flag, then we
need to loop back in order to handle it.
Fixes:
0048fdd06614 ("NFSv4.1: RECLAIM_COMPLETE must handle NFS4ERR_CONN_NOT_BOUND_TO_SESSION")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Trond Myklebust [Sun, 16 Oct 2022 18:44:31 +0000 (14:44 -0400)]
NFSv4: Fix a potential state reclaim deadlock
[ Upstream commit
1ba04394e028ea8b45d92685cc0d6ab582cf7647 ]
If the server reboots while we are engaged in a delegation return, and
there is a pNFS layout with return-on-close set, then the current code
can end up deadlocking in pnfs_roc() when nfs_inode_set_delegation()
tries to return the old delegation.
Now that delegreturn actually uses its own copy of the stateid, it
should be safe to just always update the delegation stateid in place.
Fixes:
078000d02d57 ("pNFS: We want return-on-close to complete when evicting the inode")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yangyang Li [Mon, 24 Oct 2022 08:38:13 +0000 (16:38 +0800)]
RDMA/hns: Disable local invalidate operation
[ Upstream commit
9e272ed69ad6f6952fafd0599d6993575512408e ]
When function reset and local invalidate are mixed, HNS RoCEE may hang.
Before introducing the cause of the problem, two hardware internal
concepts need to be introduced:
1. Execution queue: The queue of hardware execution instructions,
function reset and local invalidate are queued for execution in this
queue.
2.Local queue: A queue that stores local operation instructions. The
instructions in the local queue will be sent to the execution queue
for execution. The instructions in the local queue will not be removed
until the execution is completed.
The reason for the problem is as follows:
1. There is a function reset instruction in the execution queue, which
is currently being executed. A necessary condition for the successful
execution of function reset is: the hardware pipeline needs to empty
the instructions that were not completed before;
2. A local invalidate instruction at the head of the local queue is
sent to the execution queue. Now there are two instructions in the
execution queue, the first is the function reset instruction, and the
second is the local invalidate instruction, which will be executed in
se quence;
3. The user has issued many local invalidate operations, causing the
local queue to be filled up.
4. The user still has a new local operation command and is queuing to
enter the local queue. But the local queue is full and cannot receive
new instructions, this instruction is temporarily stored at the
hardware pipeline.
5. The function reset has been waiting for the instruction before the
hardware pipeline stage is drained. The hardware pipeline stage also
caches a local invalidate instruction, so the function reset cannot be
completed, and the instructions after it cannot be executed.
These factors together cause the execution logic deadlock of the hardware,
and the consequence is that RoCEE will not have any response. Considering
that the local operation command may potentially cause RoCEE to hang, this
feature is no longer supported.
Fixes:
e93df0108579 ("RDMA/hns: Support local invalidate for hip08 in kernel space")
Signed-off-by: Yangyang Li <liyangyang20@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Haoyue Xu <xuhaoyue1@hisilicon.com>
Link: https://lore.kernel.org/r/20221024083814.1089722-2-xuhaoyue1@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wenpeng Liang [Thu, 12 May 2022 08:00:11 +0000 (16:00 +0800)]
RDMA/hns: Use hr_reg_xxx() instead of remaining roce_set_xxx()
[ Upstream commit
82600b2d3cd57428bdb03c66ae67708d3c8f7281 ]
To reduce the code size and make the code clearer, replace all
roce_set_xxx() with hr_reg_xxx() to write the data fields.
Link: https://lore.kernel.org/r/20220512080012.38728-2-liangwenpeng@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of:
9e272ed69ad6 ("RDMA/hns: Disable local invalidate operation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xinhao Liu [Fri, 19 Nov 2021 14:02:08 +0000 (22:02 +0800)]
RDMA/hns: Remove magic number
[ Upstream commit
9c3631d17054a8766dbdc1abf8d29306260e7c7f ]
Don't use unintelligible constants.
Link: https://lore.kernel.org/r/20211119140208.40416-10-liangwenpeng@huawei.com
Signed-off-by: Xinhao Liu <liuxinhao5@hisilicon.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of:
9e272ed69ad6 ("RDMA/hns: Disable local invalidate operation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dean Luick [Tue, 18 Oct 2022 14:27:50 +0000 (10:27 -0400)]
IB/hfi1: Correctly move list in sc_disable()
[ Upstream commit
1afac08b39d85437187bb2a92d89a741b1078f55 ]
Commit
13bac861952a ("IB/hfi1: Fix abba locking issue with sc_disable()")
incorrectly tries to move a list from one list head to another. The
result is a kernel crash.
The crash is triggered when a link goes down and there are waiters for a
send to complete. The following signature is seen:
BUG: kernel NULL pointer dereference, address:
0000000000000030
[...]
Call Trace:
sc_disable+0x1ba/0x240 [hfi1]
pio_freeze+0x3d/0x60 [hfi1]
handle_freeze+0x27/0x1b0 [hfi1]
process_one_work+0x1b0/0x380
? process_one_work+0x380/0x380
worker_thread+0x30/0x360
? process_one_work+0x380/0x380
kthread+0xd7/0x100
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
The fix is to use the correct call to move the list.
Fixes:
13bac861952a ("IB/hfi1: Fix abba locking issue with sc_disable()")
Signed-off-by: Dean Luick <dean.luick@cornelisnetworks.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Link: https://lore.kernel.org/r/166610327042.674422.6146908799669288976.stgit@awfm-02.cornelisnetworks.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
HÃ¥kon Bugge [Wed, 12 Oct 2022 14:15:42 +0000 (16:15 +0200)]
RDMA/cma: Use output interface for net_dev check
[ Upstream commit
eb83f502adb036cd56c27e13b9ca3b2aabfa790b ]
Commit
27cfde795a96 ("RDMA/cma: Fix arguments order in net device
validation") swapped the src and dst addresses in the call to
validate_net_dev().
As a consequence, the test in validate_ipv4_net_dev() to see if the
net_dev is the right one, is incorrect for port 1 <-> 2 communication when
the ports are on the same sub-net. This is fixed by denoting the
flowi4_oif as the device instead of the incoming one.
The bug has not been observed using IPv6 addresses.
Fixes:
27cfde795a96 ("RDMA/cma: Fix arguments order in net device validation")
Signed-off-by: HÃ¥kon Bugge <haakon.bugge@oracle.com>
Link: https://lore.kernel.org/r/20221012141542.16925-1-haakon.bugge@oracle.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexander Graf [Mon, 17 Oct 2022 18:45:41 +0000 (20:45 +0200)]
KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
[ Upstream commit
1739c7017fb1d759965dcbab925ff5980a5318cb ]
The KVM_X86_SET_MSR_FILTER ioctls contains a pointer in the passed in
struct which means it has a different struct size depending on whether
it gets called from 32bit or 64bit code.
This patch introduces compat code that converts from the 32bit struct to
its 64bit counterpart which then gets used going forward internally.
With this applied, 32bit QEMU can successfully set MSR bitmaps when
running on 64bit kernels.
Reported-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Fixes:
1a155254ff937 ("KVM: x86: Introduce MSR filtering")
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <
20221017184541.2658-4-graf@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexander Graf [Mon, 17 Oct 2022 18:45:40 +0000 (20:45 +0200)]
KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
[ Upstream commit
2e3272bc1790825c43d2c39690bf2836b81c6d36 ]
In the next patch we want to introduce a second caller to
set_msr_filter() which constructs its own filter list on the stack.
Refactor the original function so it takes it as argument instead of
reading it through copy_from_user().
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <
20221017184541.2658-3-graf@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aaron Lewis [Thu, 14 Jul 2022 16:13:15 +0000 (16:13 +0000)]
KVM: x86: Protect the unused bits in MSR exiting flags
[ Upstream commit
cf5029d5dd7cb0aaa53250fa9e389abd231606b3 ]
The flags for KVM_CAP_X86_USER_SPACE_MSR and KVM_X86_SET_MSR_FILTER
have no protection for their unused bits. Without protection, future
development for these features will be difficult. Add the protection
needed to make it possible to extend these features in the future.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Message-Id: <
20220714161314.1715227-1-aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of:
2e3272bc1790 ("KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Roderick Colenbrander [Mon, 10 Oct 2022 21:23:12 +0000 (14:23 -0700)]
HID: playstation: add initial DualSense Edge controller support
[ Upstream commit
b8a968efab301743fd659b5649c5d7d3e30e63a6 ]
Provide initial support for the DualSense Edge controller. The brings
support up to the level of the original DualSense, but won't yet provide
support for new features (e.g. reprogrammable buttons).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
CC: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20221010212313.78275-3-roderick.colenbrander@sony.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Baolin Wang [Thu, 1 Sep 2022 10:41:31 +0000 (18:41 +0800)]
mm/hugetlb: fix races when looking up a CONT-PTE/PMD size hugetlb page
[ Upstream commit
fac35ba763ed07ba93154c95ffc0c4a55023707f ]
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb (2M and
1G), but also CONT-PTE/PMD size(64K and 32M) if a 4K page size specified.
So when looking up a CONT-PTE size hugetlb page by follow_page(), it will
use pte_offset_map_lock() to get the pte entry lock for the CONT-PTE size
hugetlb in follow_page_pte(). However this pte entry lock is incorrect
for the CONT-PTE size hugetlb, since we should use huge_pte_lock() to get
the correct lock, which is mm->page_table_lock.
That means the pte entry of the CONT-PTE size hugetlb under current pte
lock is unstable in follow_page_pte(), we can continue to migrate or
poison the pte entry of the CONT-PTE size hugetlb, which can cause some
potential race issues, even though they are under the 'pte lock'.
For example, suppose thread A is trying to look up a CONT-PTE size hugetlb
page by move_pages() syscall under the lock, however antoher thread B can
migrate the CONT-PTE hugetlb page at the same time, which will cause
thread A to get an incorrect page, if thread A also wants to do page
migration, then data inconsistency error occurs.
Moreover we have the same issue for CONT-PMD size hugetlb in
follow_huge_pmd().
To fix above issues, rename the follow_huge_pmd() as follow_huge_pmd_pte()
to handle PMD and PTE level size hugetlb, which uses huge_pte_lock() to
get the correct pte entry lock to make the pte entry stable.
Mike said:
Support for CONT_PMD/_PTE was added with
bb9dd3df8ee9 ("arm64: hugetlb:
refactor find_num_contig()"). Patch series "Support for contiguous pte
hugepages", v4. However, I do not believe these code paths were
executed until migration support was added with
5480280d3f2d ("arm64/mm:
enable HugeTLB migration for contiguous bit HugeTLB pages") I would go
with
5480280d3f2d for the Fixes: targe.
Link: https://lkml.kernel.org/r/635f43bdd85ac2615a58405da82b4d33c6e5eb05.1662017562.git.baolin.wang@linux.alibaba.com
Fixes:
5480280d3f2d ("arm64/mm: enable HugeTLB migration for contiguous bit HugeTLB pages")
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shirish S [Fri, 7 Oct 2022 15:01:49 +0000 (20:31 +0530)]
drm/amd/display: explicitly disable psr_feature_enable appropriately
[ Upstream commit
6094b9136ca9038b61e9c4b5d25cd5512ce50b34 ]
[Why]
If psr_feature_enable is set to true by default, it continues to be enabled
for non capable links.
[How]
explicitly disable the feature on links that are not capable of the same.
Fixes:
8c322309e48e9 ("drm/amd/display: Enable PSR")
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sean Christopherson [Tue, 30 Aug 2022 23:15:55 +0000 (23:15 +0000)]
KVM: x86: Treat #DBs from the emulator as fault-like (code and DR7.GD=1)
[ Upstream commit
5623f751bd9c438ed12840e086f33c4646440d19 ]
Add a dedicated "exception type" for #DBs, as #DBs can be fault-like or
trap-like depending the sub-type of #DB, and effectively defer the
decision of what to do with the #DB to the caller.
For the emulator's two calls to exception_type(), treat the #DB as
fault-like, as the emulator handles only code breakpoint and general
detect #DBs, both of which are fault-like.
For event injection, which uses exception_type() to determine whether to
set EFLAGS.RF=1 on the stack, keep the current behavior of not setting
RF=1 for #DBs. Intel and AMD explicitly state RF isn't set on code #DBs,
so exempting by failing the "== EXCPT_FAULT" check is correct. The only
other fault-like #DB is General Detect, and despite Intel and AMD both
strongly implying (through omission) that General Detect #DBs should set
RF=1, hardware (multiple generations of both Intel and AMD), in fact does
not. Through insider knowledge, extreme foresight, sheer dumb luck, or
some combination thereof, KVM correctly handled RF for General Detect #DBs.
Fixes:
38827dbd3fb8 ("KVM: x86: Do not update EFLAGS on faulting emulation")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20220830231614.3580124-9-seanjc@google.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sean Christopherson [Sun, 1 May 2022 22:07:31 +0000 (00:07 +0200)]
KVM: x86: Trace re-injected exceptions
[ Upstream commit
a61d7c5432ac5a953bbcec17af031661c2bd201d ]
Trace exceptions that are re-injected, not just those that KVM is
injecting for the first time. Debugging re-injection bugs is painful
enough as is, not having visibility into what KVM is doing only makes
things worse.
Delay propagating pending=>injected in the non-reinjection path so that
the tracing can properly identify reinjected exceptions.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <
25470690a38b4d2b32b6204875dd35676c65c9f2.
1651440202.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of:
5623f751bd9c ("KVM: x86: Treat #DBs from the emulator as fault-like (code and DR7.GD=1)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lukas Wunner [Sat, 5 Nov 2022 13:46:40 +0000 (09:46 -0400)]
serial: ar933x: Deassert Transmit Enable on ->rs485_config()
commit
3a939433ddc1bab98be028903aaa286e5e7461d7 upstream.
The ar933x_uart driver neglects to deassert Transmit Enable when
->rs485_config() is invoked. Fix it.
Fixes:
9be1064fe524 ("serial: ar933x_uart: add RS485 support")
Cc: stable@vger.kernel.org # v5.7+
Cc: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Ilpo JÀrvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 19 Aug 2022 01:17:32 +0000 (18:17 -0700)]
scsi: lpfc: Rework MIB Rx Monitor debug info logic
[ Upstream commit
bd269188ea94e40ab002cad7b0df8f12b8f0de54 ]
The kernel test robot reported the following sparse warning:
arch/arm64/include/asm/cmpxchg.h:88:1: sparse: sparse: cast truncates
bits from constant value (369 becomes 69)
On arm64, atomic_xchg only works on 8-bit byte fields. Thus, the macro
usage of LPFC_RXMONITOR_TABLE_IN_USE can be unintentionally truncated
leading to all logic involving the LPFC_RXMONITOR_TABLE_IN_USE macro to not
work properly.
Replace the Rx Table atomic_t indexing logic with a new
lpfc_rx_info_monitor structure that holds a circular ring buffer. For
locking semantics, a spinlock_t is used.
Link: https://lore.kernel.org/r/20220819011736.14141-4-jsmart2021@gmail.com
Fixes:
17b27ac59224 ("scsi: lpfc: Add rx monitoring statistics")
Cc: <stable@vger.kernel.org> # v5.15+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Sat, 4 Dec 2021 00:26:41 +0000 (16:26 -0800)]
scsi: lpfc: Adjust CMF total bytes and rxmonitor
[ Upstream commit
a6269f837045acb02904f31f05acde847ec8f8a7 ]
Calculate any extra bytes needed to account for timer accuracy. If we are
less than LPFC_CMF_INTERVAL, then calculate the adjustment needed for total
to reflect a full LPFC_CMF_INTERVAL.
Add additional info to rxmonitor, and adjust some log formatting.
Link: https://lore.kernel.org/r/20211204002644.116455-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of:
bd269188ea94 ("scsi: lpfc: Rework MIB Rx Monitor debug info logic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 10 Sep 2021 23:31:55 +0000 (16:31 -0700)]
scsi: lpfc: Adjust bytes received vales during cmf timer interval
[ Upstream commit
d5ac69b332d8859d1f8bd5d4dee31f3267f6b0d2 ]
The newly added congestion mgmt framework is seeing unexpected congestion
FPINs and signals. In analysis, time values given to the adapter are not
at hard time intervals. Thus the drift vs the transfer count seen is
affecting how the framework manages things.
Adjust counters to cover the drift.
Link: https://lore.kernel.org/r/20210910233159.115896-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of:
bd269188ea94 ("scsi: lpfc: Rework MIB Rx Monitor debug info logic")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Thu, 3 Nov 2022 14:59:20 +0000 (23:59 +0900)]
Linux 5.15.77
Link: https://lore.kernel.org/r/20221102022059.593236470@linuxfoundation.org
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Allen Pais <apais@linux.microsoft.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kuniyuki Iwashima [Thu, 6 Oct 2022 18:53:45 +0000 (11:53 -0700)]
tcp/udp: Fix memory leak in ipv6_renew_options().
commit
3c52c6bb831f6335c176a0fc7214e26f43adbd11 upstream.
syzbot reported a memory leak [0] related to IPV6_ADDRFORM.
The scenario is that while one thread is converting an IPv6 socket into
IPv4 with IPV6_ADDRFORM, another thread calls do_ipv6_setsockopt() and
allocates memory to inet6_sk(sk)->XXX after conversion.
Then, the converted sk with (tcp|udp)_prot never frees the IPv6 resources,
which inet6_destroy_sock() should have cleaned up.
setsockopt(IPV6_ADDRFORM) setsockopt(IPV6_DSTOPTS)
+-----------------------+ +----------------------+
- do_ipv6_setsockopt(sk, ...)
- sockopt_lock_sock(sk) - do_ipv6_setsockopt(sk, ...)
- lock_sock(sk) ^._ called via tcpv6_prot
- WRITE_ONCE(sk->sk_prot, &tcp_prot) before WRITE_ONCE()
- xchg(&np->opt, NULL)
- txopt_put(opt)
- sockopt_release_sock(sk)
- release_sock(sk) - sockopt_lock_sock(sk)
- lock_sock(sk)
- ipv6_set_opt_hdr(sk, ...)
- ipv6_update_options(sk, opt)
- xchg(&inet6_sk(sk)->opt, opt)
^._ opt is never freed.
- sockopt_release_sock(sk)
- release_sock(sk)
Since IPV6_DSTOPTS allocates options under lock_sock(), we can avoid this
memory leak by testing whether sk_family is changed by IPV6_ADDRFORM after
acquiring the lock.
This issue exists from the initial commit between IPV6_ADDRFORM and
IPV6_PKTOPTIONS.
[0]:
BUG: memory leak
unreferenced object 0xffff888009ab9f80 (size 96):
comm "syz-executor583", pid 328, jiffies
4294916198 (age 13.034s)
hex dump (first 32 bytes):
01 00 00 00 48 00 00 00 08 00 00 00 00 00 00 00 ....H...........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
000000002ee98ae1>] kmalloc include/linux/slab.h:605 [inline]
[<
000000002ee98ae1>] sock_kmalloc+0xb3/0x100 net/core/sock.c:2566
[<
0000000065d7b698>] ipv6_renew_options+0x21e/0x10b0 net/ipv6/exthdrs.c:1318
[<
00000000a8c756d7>] ipv6_set_opt_hdr net/ipv6/ipv6_sockglue.c:354 [inline]
[<
00000000a8c756d7>] do_ipv6_setsockopt.constprop.0+0x28b7/0x4350 net/ipv6/ipv6_sockglue.c:668
[<
000000002854d204>] ipv6_setsockopt+0xdf/0x190 net/ipv6/ipv6_sockglue.c:1021
[<
00000000e69fdcf8>] tcp_setsockopt+0x13b/0x2620 net/ipv4/tcp.c:3789
[<
0000000090da4b9b>] __sys_setsockopt+0x239/0x620 net/socket.c:2252
[<
00000000b10d192f>] __do_sys_setsockopt net/socket.c:2263 [inline]
[<
00000000b10d192f>] __se_sys_setsockopt net/socket.c:2260 [inline]
[<
00000000b10d192f>] __x64_sys_setsockopt+0xbe/0x160 net/socket.c:2260
[<
000000000a80d7aa>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<
000000000a80d7aa>] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80
[<
000000004562b5c6>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Meena Shanmugam <meenashanmugam@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Thu, 22 Sep 2022 16:27:33 +0000 (18:27 +0200)]
serial: Deassert Transmit Enable on probe in driver-specific way
commit
7c7f9bc986e698873b489c371a08f206979d06b7 upstream.
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes:
d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Daisuke Mizobuchi <mizo@atmark-techno.com>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lino Sanfilippo [Sun, 10 Apr 2022 10:46:34 +0000 (12:46 +0200)]
serial: core: move RS485 configuration tasks from drivers into core
commit
0ed12afa5655512ee418047fb3546d229df20aa1 upstream.
Several drivers that support setting the RS485 configuration via userspace
implement one or more of the following tasks:
- in case of an invalid RTS configuration (both RTS after send and RTS on
send set or both unset) fall back to enable RTS on send and disable RTS
after send
- nullify the padding field of the returned serial_rs485 struct
- copy the configuration into the uart port struct
- limit RTS delays to 100 ms
Move these tasks into the serial core to make them generic and to provide
a consistent behaviour among all drivers.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-2-LinoSanfilippo@gmx.de
Signed-off-by: Daisuke Mizobuchi <mizo@atmark-techno.com>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Biju Das [Tue, 25 Oct 2022 15:56:55 +0000 (16:56 +0100)]
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
commit
702de2c21eed04c67cefaaedc248ef16e5f6b293 upstream.
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes:
dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[biju: removed gpriv from RCANFD_RFCC_RFIE macro]
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Biju Das [Tue, 25 Oct 2022 15:56:56 +0000 (16:56 +0100)]
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
commit
d887087c896881715c1a82f1d4f71fbfe5344ffd upstream.
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes:
76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[biju: fixed the conflicts manually]
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Kuai [Tue, 1 Nov 2022 01:31:24 +0000 (09:31 +0800)]
scsi: sd: Revert "scsi: sd: Remove a local variable"
This reverts commit
84f7a9de0602704bbec774a6c7f7c8c4994bee9c.
Because it introduces a problem that rq->__data_len is set to the wrong
value.
before the patch:
1) nr_bytes = rq->__data_len
2) rq->__data_len = sdp->sector_size
3) scsi_init_io()
4) rq->__data_len = nr_bytes
after the patch:
1) rq->__data_len = sdp->sector_size
2) scsi_init_io()
3) rq->__data_len = rq->__data_len -> __data_len is wrong
It will cause that io can only complete one segment each time, and the io
will requeue in scsi_io_completion_action(), which will cause severe
performance degradation.
Scsi write same is removed in commit
e383e16e84e9 ("scsi: sd: Remove
WRITE_SAME support") from mainline, hence this patch is only needed for
stable kernels.
Fixes:
84f7a9de0602 ("scsi: sd: Remove a local variable")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
D Scott Phillips [Tue, 11 Oct 2022 02:21:40 +0000 (19:21 -0700)]
arm64: Add AMPERE1 to the Spectre-BHB affected list
[ Upstream commit
0e5d5ae837c8ce04d2ddb874ec5f920118bd9d31 ]
Per AmpereOne erratum AC03_CPU_12, "Branch history may allow control of
speculative execution across software contexts," the AMPERE1 core needs the
bhb clearing loop to mitigate Spectre-BHB, with a loop iteration count of
11.
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20221011022140.432370-1-scott@os.amperecomputing.com
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Vladimir Oltean [Thu, 27 Oct 2022 18:29:25 +0000 (21:29 +0300)]
net: enetc: survive memory pressure without crashing
[ Upstream commit
84ce1ca3fe9e1249bf21176ff162200f1c4e5ed1 ]
Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes:
d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Dumazet [Thu, 27 Oct 2022 04:06:37 +0000 (04:06 +0000)]
kcm: do not sense pfmemalloc status in kcm_sendpage()
[ Upstream commit
ee15e1f38dc201fa7d63c13aa258b728dce27f4d ]
Similar to changes done in TCP in blamed commit.
We should not sense pfmemalloc status in sendpage() methods.
Fixes:
326140063946 ("tcp: TX zerocopy should not sense pfmemalloc status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221027040637.1107703-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Dumazet [Thu, 27 Oct 2022 04:03:46 +0000 (04:03 +0000)]
net: do not sense pfmemalloc status in skb_append_pagefrags()
[ Upstream commit
228ebc41dfab5b5d34cd76835ddb0ca8ee12f513 ]
skb_append_pagefrags() is used by af_unix and udp sendpage()
implementation so far.
In commit
326140063946 ("tcp: TX zerocopy should not sense
pfmemalloc status") we explained why we should not sense
pfmemalloc status for pages owned by user space.
We should also use skb_fill_page_desc_noacc()
in skb_append_pagefrags() to avoid following KCSAN report:
BUG: KCSAN: data-race in lru_add_fn / skb_append_pagefrags
write to 0xffffea00058fc1c8 of 8 bytes by task 17319 on cpu 0:
__list_add include/linux/list.h:73 [inline]
list_add include/linux/list.h:88 [inline]
lruvec_add_folio include/linux/mm_inline.h:323 [inline]
lru_add_fn+0x327/0x410 mm/swap.c:228
folio_batch_move_lru+0x1e1/0x2a0 mm/swap.c:246
lru_add_drain_cpu+0x73/0x250 mm/swap.c:669
lru_add_drain+0x21/0x60 mm/swap.c:773
free_pages_and_swap_cache+0x16/0x70 mm/swap_state.c:311
tlb_batch_pages_flush mm/mmu_gather.c:59 [inline]
tlb_flush_mmu_free mm/mmu_gather.c:256 [inline]
tlb_flush_mmu+0x5b2/0x640 mm/mmu_gather.c:263
tlb_finish_mmu+0x86/0x100 mm/mmu_gather.c:363
exit_mmap+0x190/0x4d0 mm/mmap.c:3098
__mmput+0x27/0x1b0 kernel/fork.c:1185
mmput+0x3d/0x50 kernel/fork.c:1207
copy_process+0x19fc/0x2100 kernel/fork.c:2518
kernel_clone+0x166/0x550 kernel/fork.c:2671
__do_sys_clone kernel/fork.c:2812 [inline]
__se_sys_clone kernel/fork.c:2796 [inline]
__x64_sys_clone+0xc3/0xf0 kernel/fork.c:2796
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffffea00058fc1c8 of 8 bytes by task 17325 on cpu 1:
page_is_pfmemalloc include/linux/mm.h:1817 [inline]
__skb_fill_page_desc include/linux/skbuff.h:2432 [inline]
skb_fill_page_desc include/linux/skbuff.h:2453 [inline]
skb_append_pagefrags+0x210/0x600 net/core/skbuff.c:3974
unix_stream_sendpage+0x45e/0x990 net/unix/af_unix.c:2338
kernel_sendpage+0x184/0x300 net/socket.c:3561
sock_sendpage+0x5a/0x70 net/socket.c:1054
pipe_to_sendpage+0x128/0x160 fs/splice.c:361
splice_from_pipe_feed fs/splice.c:415 [inline]
__splice_from_pipe+0x222/0x4d0 fs/splice.c:559
splice_from_pipe fs/splice.c:594 [inline]
generic_splice_sendpage+0x89/0xc0 fs/splice.c:743
do_splice_from fs/splice.c:764 [inline]
direct_splice_actor+0x80/0xa0 fs/splice.c:931
splice_direct_to_actor+0x305/0x620 fs/splice.c:886
do_splice_direct+0xfb/0x180 fs/splice.c:974
do_sendfile+0x3bf/0x910 fs/read_write.c:1255
__do_sys_sendfile64 fs/read_write.c:1323 [inline]
__se_sys_sendfile64 fs/read_write.c:1309 [inline]
__x64_sys_sendfile64+0x10c/0x150 fs/read_write.c:1309
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x0000000000000000 -> 0xffffea00058fc188
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 17325 Comm: syz-executor.0 Not tainted 6.1.0-rc1-syzkaller-00158-g440b7895c990-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/11/2022
Fixes:
326140063946 ("tcp: TX zerocopy should not sense pfmemalloc status")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221027040346.1104204-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Suresh Devarakonda [Wed, 26 Oct 2022 13:51:49 +0000 (14:51 +0100)]
net/mlx5: Fix crash during sync firmware reset
[ Upstream commit
aefb62a9988749703435e941704624949a80a2a9 ]
When setting Bluefield to DPU NIC mode using mlxconfig tool + sync
firmware reset flow, we run into scenario where the host was not
eswitch manager at the time of mlx5 driver load but becomes eswitch manager
after the sync firmware reset flow. This results in null pointer
access of mpfs structure during mac filter add. This change prevents null
pointer access but mpfs table entries will not be added.
Fixes:
5ec697446f46 ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Suresh Devarakonda <ramad@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Roy Novich [Wed, 26 Oct 2022 13:51:48 +0000 (14:51 +0100)]
net/mlx5: Update fw fatal reporter state on PCI handlers successful recover
[ Upstream commit
416ef713631937cf5452476a7f1041a3ae7b06c6 ]
Update devlink health fw fatal reporter state to "healthy" is needed by
strictly calling devlink_health_reporter_state_update() after recovery
was done by PCI error handler. This is needed when fw_fatal reporter was
triggered due to PCI error. Poll health is called and set reporter state
to error. Health recovery failed (since EEH didn't re-enable the PCI).
PCI handlers keep on recover flow and succeed later without devlink
acknowledgment. Fix this by adding devlink state update at the end of
the PCI handler recovery process.
Fixes:
6181e5cb752e ("devlink: add support for reporter recovery completion")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Saeed Mahameed [Tue, 5 Oct 2021 01:39:51 +0000 (18:39 -0700)]
net/mlx5: Print more info on pci error handlers
[ Upstream commit
fad1783a6d669ac82b6ea4f2f32b4ba2b5484920 ]
In case mlx5_pci_err_detected was called with state equals to
pci_channel_io_perm_failure, the driver will never come back up.
It is nice to know why the driver went to zombie land, so print some
useful information on pci err handlers.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Stable-dep-of:
416ef7136319 ("net/mlx5: Update fw fatal reporter state on PCI handlers successful recover")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tariq Toukan [Wed, 26 Oct 2022 13:51:45 +0000 (14:51 +0100)]
net/mlx5: Fix possible use-after-free in async command interface
[ Upstream commit
bacd22df95147ed673bec4692ab2d4d585935241 ]
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr
ffff888139cd12f4 by task swapper/5/0
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x7d
print_report.cold+0x2d5/0x684
? do_raw_spin_lock+0x23d/0x270
kasan_report+0xb1/0x1a0
? do_raw_spin_lock+0x23d/0x270
do_raw_spin_lock+0x23d/0x270
? rwlock_bug.part.0+0x90/0x90
? __delete_object+0xb8/0x100
? lock_downgrade+0x6e0/0x6e0
_raw_spin_lock_irqsave+0x43/0x60
? __wake_up_common_lock+0xb9/0x140
__wake_up_common_lock+0xb9/0x140
? __wake_up_common+0x650/0x650
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kasan_set_track+0x21/0x30
? destroy_tis_callback+0x53/0x70 [mlx5_core]
? kfree+0x1ba/0x520
? do_raw_spin_unlock+0x54/0x220
mlx5_cmd_exec_cb_handler+0x136/0x1a0 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
? mlx5_cmd_cleanup_async_ctx+0x220/0x220 [mlx5_core]
mlx5_cmd_comp_handler+0x65a/0x12b0 [mlx5_core]
? dump_command+0xcc0/0xcc0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
cmd_comp_notifier+0x7e/0xb0 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
mlx5_eq_async_int+0x3ce/0xa20 [mlx5_core]
atomic_notifier_call_chain+0xd7/0x1d0
? irq_release+0x140/0x140 [mlx5_core]
irq_int_handler+0x19/0x30 [mlx5_core]
__handle_irq_event_percpu+0x1f2/0x620
handle_irq_event+0xb2/0x1d0
handle_edge_irq+0x21e/0xb00
__common_interrupt+0x79/0x1a0
common_interrupt+0x78/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x42/0x60
Code: c1 83 e0 07 48 c1 e9 03 83 c0 03 0f b6 14 11 38 d0 7c 04 84 d2 75 14 8b 05 eb 47 22 02 85 c0 7e 07 0f 00 2d e0 9f 48 00 fb f4 <c3> 48 c7 c7 80 08 7f 85 e8 d1 d3 3e fe eb de 66 66 2e 0f 1f 84 00
RSP: 0018:
ffff888100dbfdf0 EFLAGS:
00000242
RAX:
0000000000000001 RBX:
ffffffff84ecbd48 RCX:
1ffffffff0afe110
RDX:
0000000000000004 RSI:
0000000000000000 RDI:
ffffffff835cc9bc
RBP:
0000000000000005 R08:
0000000000000001 R09:
ffff88881dec4ac3
R10:
ffffed1103bd8958 R11:
0000017d0ca571c9 R12:
0000000000000005
R13:
ffffffff84f024e0 R14:
0000000000000000 R15:
dffffc0000000000
? default_idle_call+0xcc/0x450
default_idle_call+0xec/0x450
do_idle+0x394/0x450
? arch_cpu_idle_exit+0x40/0x40
? do_idle+0x17/0x450
cpu_startup_entry+0x19/0x20
start_secondary+0x221/0x2b0
? set_cpu_sibling_map+0x2070/0x2070
secondary_startup_64_no_verify+0xcd/0xdb
</TASK>
Allocated by task 49502:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
kvmalloc_node+0x48/0xe0
mlx5e_bulk_async_init+0x35/0x110 [mlx5_core]
mlx5e_tls_priv_tx_list_cleanup+0x84/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 49502:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_set_free_info+0x20/0x30
____kasan_slab_free+0x11d/0x1b0
kfree+0x1ba/0x520
mlx5e_tls_priv_tx_list_cleanup+0x2e7/0x3e0 [mlx5_core]
mlx5e_ktls_cleanup_tx+0x38f/0x760 [mlx5_core]
mlx5e_cleanup_nic_tx+0xa7/0x100 [mlx5_core]
mlx5e_detach_netdev+0x1ca/0x2b0 [mlx5_core]
mlx5e_suspend+0xdb/0x140 [mlx5_core]
mlx5e_remove+0x89/0x190 [mlx5_core]
auxiliary_bus_remove+0x52/0x70
device_release_driver_internal+0x40f/0x650
driver_detach+0xc1/0x180
bus_remove_driver+0x125/0x2f0
auxiliary_driver_unregister+0x16/0x50
mlx5e_cleanup+0x26/0x30 [mlx5_core]
cleanup+0xc/0x4e [mlx5_core]
__x64_sys_delete_module+0x2b5/0x450
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes:
e355477ed9e4 ("net/mlx5: Make mlx5_cmd_exec_cb() a safe API")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-8-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aya Levin [Wed, 26 Oct 2022 13:51:42 +0000 (14:51 +0100)]
net/mlx5e: Extend SKB room check to include PTP-SQ
[ Upstream commit
19b43a432e3e47db656a8269a74b50aef826950c ]
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes:
1880bc4e4a96 ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hyong Youb Kim [Wed, 26 Oct 2022 13:51:39 +0000 (14:51 +0100)]
net/mlx5e: Do not increment ESN when updating IPsec ESN state
[ Upstream commit
888be6b279b7257b5f6e4c9527675bff0a335596 ]
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes:
cb01008390bb ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhengchao Shao [Wed, 26 Oct 2022 01:46:42 +0000 (09:46 +0800)]
netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir failed
[ Upstream commit
a6aa8d0ce2cfba57ac0f23293fcb3be0b9f53fba ]
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed.
Otherwise, the netdevsim device will not be created next time. Kernel
reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim'
already present!
Fixes:
ab1d0cc004d7 ("netdevsim: change debugfs tree topology")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rafał Miłecki [Thu, 27 Oct 2022 11:24:30 +0000 (13:24 +0200)]
net: broadcom: bcm4908_enet: update TX stats after actual transmission
[ Upstream commit
ef3556ee16c68735ec69bd08df41d1cd83b14ad3 ]
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes:
4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Colin Ian King [Wed, 22 Dec 2021 00:39:37 +0000 (00:39 +0000)]
net: broadcom: bcm4908enet: remove redundant variable bytes
[ Upstream commit
62a3106697f3c6f9af64a2cd0f9ff58552010dc8 ]
The variable bytes is being used to summate slot lengths,
however the value is never used afterwards. The summation
is redundant so remove variable bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211222003937.727325-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of:
ef3556ee16c6 ("net: broadcom: bcm4908_enet: update TX stats after actual transmission")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicolas Dichtel [Thu, 20 Oct 2022 10:09:52 +0000 (12:09 +0200)]
nh: fix scope used to find saddr when adding non gw nh
[ Upstream commit
bac0f937c343d651874f83b265ca8f5070ed4f06 ]
As explained by Julian, fib_nh_scope is related to fib_nh_gw4, but
fib_info_update_nhc_saddr() needs the scope of the route, which is
the scope "before" fib_nh_scope, ie fib_nh_scope - 1.
This patch fixes the problem described in commit
747c14307214 ("ip: fix
dflt addr selection for connected nexthop").
Fixes:
597cfe4fc339 ("nexthop: Add support for IPv4 nexthops")
Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian Fainelli [Tue, 25 Oct 2022 23:42:01 +0000 (16:42 -0700)]
net: bcmsysport: Indicate MAC is in charge of PHY PM
[ Upstream commit
9f172134dde7e4f5bf4b9139f23a1e741ec1c36e ]
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT
driver essentially does exactly what mdio_bus_phy_resume() does by
calling phy_resume().
Fixes:
fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221025234201.2549360-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Tue, 25 Oct 2022 13:00:11 +0000 (21:00 +0800)]
net: ehea: fix possible memory leak in ehea_register_port()
[ Upstream commit
0e7ce23a917a9cc83ca3c779fbba836bca3bcf1e ]
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
Fixes:
1acf2318dd13 ("ehea: dynamic add / remove port")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221025130011.1071357-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Aaron Conole [Tue, 25 Oct 2022 10:50:17 +0000 (06:50 -0400)]
openvswitch: switch from WARN to pr_warn
[ Upstream commit
fd954cc1919e35cb92f78671cab6e42d661945a3 ]
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com
Fixes:
44da5ae5fbea ("openvswitch: Drop user features if old user space attempted to create datapath")
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Iwai [Thu, 27 Oct 2022 06:52:33 +0000 (08:52 +0200)]
ALSA: aoa: Fix I2S device accounting
[ Upstream commit
f1fae475f10a26b7e34da4ff2e2f19b7feb3548e ]
i2sbus_add_dev() is supposed to return the number of probed devices,
i.e. either 1 or 0. However, i2sbus_add_dev() has one error handling
that returns -ENODEV; this will screw up the accumulation number
counted in the caller, i2sbus_probe().
Fix the return value to 0 and add the comment for better understanding
for readers.
Fixes:
f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa")
Link: https://lore.kernel.org/r/20221027065233.13292-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Thu, 27 Oct 2022 01:34:38 +0000 (09:34 +0800)]
ALSA: aoa: i2sbus: fix possible memory leak in i2sbus_add_dev()
[ Upstream commit
4a4c8482e370d697738a78dcd7bf2780832cb712 ]
dev_set_name() in soundbus_add_one() allocates memory for name, it need be
freed when of_device_register() fails, call soundbus_dev_put() to give up
the reference that hold in device_initialize(), so that it can be freed in
kobject_cleanup() when the refcount hit to 0. And other resources are also
freed in i2sbus_release_dev(), so it can return 0 directly.
Fixes:
f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221027013438.991920-1-yangyingliang@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kunihiko Hayashi [Mon, 24 Oct 2022 07:22:27 +0000 (16:22 +0900)]
net: ethernet: ave: Fix MAC to be in charge of PHY PM
[ Upstream commit
e2badb4bd33abe13ddc35975bd7f7f8693955a4b ]
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes:
fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Juergen Borleis [Mon, 24 Oct 2022 08:05:52 +0000 (10:05 +0200)]
net: fec: limit register access on i.MX6UL
[ Upstream commit
0a8b43b12dd78daa77a7dc007b92770d262a2714 ]
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes:
a51d3ab50702 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shang XiaoJing [Fri, 21 Oct 2022 10:50:33 +0000 (18:50 +0800)]
perf vendor events arm64: Fix incorrect Hisi hip08 L3 metrics
[ Upstream commit
e9229d5b6254a75291536f582652c599957344d2 ]
Commit
0cc177cfc95d565e ("perf vendor events arm64: Add Hisi hip08 L3
metrics") add L3 metrics of hip08, but some metrics (IF_BP_MISP_BR_RET,
IF_BP_MISP_BR_RET, IF_BP_MISP_BR_BL) have incorrect event number due to
the mistakes in document, which caused incorrect result. Fix the
incorrect metrics.
Before:
65,811,214,308 armv8_pmuv3_0/event=0x1014/ # 18.87 push_branch
# -40.19 other_branch
3,564,316,780 BR_MIS_PRED # 0.51 indirect_branch
# 21.81 pop_branch
After:
6,537,146,245 BR_MIS_PRED # 0.48 indirect_branch
# 0.47 pop_branch
# 0.00 push_branch
# 0.05 other_branch
Fixes:
0cc177cfc95d565e ("perf vendor events arm64: Add Hisi hip08 L3 metrics")
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Acked-by: James Clark <james.clark@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221021105035.10000-2-shangxiaojing@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sudeep Holla [Tue, 25 Oct 2022 12:34:32 +0000 (13:34 +0100)]
PM: domains: Fix handling of unavailable/disabled idle states
[ Upstream commit
e0c57a5c70c13317238cb19a7ded0eab4a5f7de5 ]
Platforms can provide the information about the availability of each
idle states via status flag. Platforms may have to disable one or more
idle states for various reasons like broken firmware or other unmet
dependencies.
Fix handling of such unavailable/disabled idle states by ignoring them
while parsing the states.
Fixes:
a3381e3a65cb ("PM / domains: Fix up domain-idle-states OF parsing")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Mon, 24 Oct 2022 13:13:38 +0000 (21:13 +0800)]
net: ksz884x: fix missing pci_disable_device() on error in pcidev_init()
[ Upstream commit
5da6d65590a0698199df44d095e54b0ed1708178 ]
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Fixes:
8ca86fd83eae ("net: Micrel KSZ8841/2 PCI Ethernet driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Slawomir Laba [Mon, 24 Oct 2022 10:05:26 +0000 (03:05 -0700)]
i40e: Fix flow-type by setting GL_HASH_INSET registers
[ Upstream commit
3b32c9932853e11d71f9db012d69e92e4669ba23 ]
Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.
Fixes:
eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sylwester Dziedziuch [Mon, 24 Oct 2022 10:05:25 +0000 (03:05 -0700)]
i40e: Fix VF hang when reset is triggered on another VF
[ Upstream commit
52424f974bc53c26ba3f00300a00e9de9afcd972 ]
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes:
3ba9bcb4b68f ("i40e: add locking around VF reset")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Slawomir Laba [Mon, 24 Oct 2022 10:05:24 +0000 (03:05 -0700)]
i40e: Fix ethtool rx-flow-hash setting for X722
[ Upstream commit
54b5af5a438076082d482cab105b1bd484ab5074 ]
When enabling flow type for RSS hash via ethtool:
ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes:
eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Dumazet [Mon, 24 Oct 2022 02:01:24 +0000 (19:01 -0700)]
ipv6: ensure sane device mtu in tunnels
[ Upstream commit
d89d7ff01235f218dad37de84457717f699dee79 ]
Another syzbot report [1] with no reproducer hints
at a bug in ip6_gre tunnel (dev:ip6gretap0)
Since ipv6 mcast code makes sure to read dev->mtu once
and applies a sanity check on it (see commit
b9b312a7a451
"ipv6: mcast: better catch silly mtu values"), a remaining
possibility is that a layer is able to set dev->mtu to
an underflowed value (high order bit set).
This could happen indeed in ip6gre_tnl_link_config_route(),
ip6_tnl_link_config() and ipip6_tunnel_bind_dev()
Make sure to sanitize mtu value in a local variable before
it is written once on dev->mtu, as lockless readers could
catch wrong temporary value.
[1]
skbuff: skb_over_panic: text:
ffff80000b7a2f38 len:40 put:40 head:
ffff000149dcf200 data:
ffff000149dcf2b0 tail:0xd8 end:0xc0 dev:ip6gretap0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:120
Internal error: Oops - BUG:
00000000f2000800 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 10241 Comm: kworker/1:1 Not tainted 6.0.0-rc7-syzkaller-18095-gbbed346d5a96 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/30/2022
Workqueue: mld mld_ifc_work
pstate:
60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : skb_panic+0x4c/0x50 net/core/skbuff.c:116
lr : skb_panic+0x4c/0x50 net/core/skbuff.c:116
sp :
ffff800020dd3b60
x29:
ffff800020dd3b70 x28:
0000000000000000 x27:
ffff00010df2a800
x26:
00000000000000c0 x25:
00000000000000b0 x24:
ffff000149dcf200
x23:
00000000000000c0 x22:
00000000000000d8 x21:
ffff80000b7a2f38
x20:
ffff00014c2f7800 x19:
0000000000000028 x18:
00000000000001a9
x17:
0000000000000000 x16:
ffff80000db49158 x15:
ffff000113bf1a80
x14:
0000000000000000 x13:
00000000ffffffff x12:
ffff000113bf1a80
x11:
ff808000081c0d5c x10:
0000000000000000 x9 :
73f125dc5c63ba00
x8 :
73f125dc5c63ba00 x7 :
ffff800008161d1c x6 :
0000000000000000
x5 :
0000000000000080 x4 :
0000000000000001 x3 :
0000000000000000
x2 :
ffff0001fefddcd0 x1 :
0000000100000000 x0 :
0000000000000089
Call trace:
skb_panic+0x4c/0x50 net/core/skbuff.c:116
skb_over_panic net/core/skbuff.c:125 [inline]
skb_put+0xd4/0xdc net/core/skbuff.c:2049
ip6_mc_hdr net/ipv6/mcast.c:1714 [inline]
mld_newpack+0x14c/0x270 net/ipv6/mcast.c:1765
add_grhead net/ipv6/mcast.c:1851 [inline]
add_grec+0xa20/0xae0 net/ipv6/mcast.c:1989
mld_send_cr+0x438/0x5a8 net/ipv6/mcast.c:2115
mld_ifc_work+0x38/0x290 net/ipv6/mcast.c:2653
process_one_work+0x2d8/0x504 kernel/workqueue.c:2289
worker_thread+0x340/0x610 kernel/workqueue.c:2436
kthread+0x12c/0x158 kernel/kthread.c:376
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860
Code:
91011400 aa0803e1 a90027ea 94373093 (
d4210000)
Fixes:
c12b395a4664 ("gre: Support GRE over IPv6")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221024020124.3756833-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kajol Jain [Fri, 14 Oct 2022 14:02:20 +0000 (19:32 +0530)]
perf vendor events power10: Fix hv-24x7 metric events
[ Upstream commit
b92dd11725a7c57f55e148c7d3ce58a86f480575 ]
Testcase stat_all_metrics.sh fails in powerpc:
90: perf all metrics test : FAILED!
The testcase "stat_all_metrics.sh" verifies perf stat result for all the
metric events present in perf list. It runs perf metric events with
various commands and expects non-empty metric result.
Incase of powerpc:hv-24x7 events, some of the event count can be 0 based
on system configuration. And if that event used as denominator in divide
equation, it can cause divide by 0 error. The current nest_metric.json
file creating divide by 0 issue for some of the metric events, which
results in failure of the "stat_all_metrics.sh" test case.
Most of the metrics events have cycles or an event which expect to have
a larger value as denominator, so adding 1 to the denominator of the
metric expression as a fix.
Result in powerpc box after this patch changes:
90: perf all metrics test : Ok
Fixes:
a3cbcadfdfc330c2 ("perf vendor events power10: Adds 24x7 nest metric events for power10 platform")
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Disha Goel <disgoel@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nageswara R Sastry <rnsastry@linux.ibm.com>
Link: https://lore.kernel.org/r/20221014140220.122251-1-kjain@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Mon, 17 Oct 2022 14:09:06 +0000 (15:09 +0100)]
media: vivid: set num_in/outputs to 0 if not supported
[ Upstream commit
69d78a80da4ef12faf2a6f9cfa2097ab4ac43983 ]
If node_types does not have video/vbi/meta inputs or outputs,
then set num_inputs/num_outputs to 0 instead of 1.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes:
0c90f649d2f5 (media: vivid: add vivid_create_queue() helper)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Wed, 12 Oct 2022 15:46:17 +0000 (16:46 +0100)]
media: videodev2.h: V4L2_DV_BT_BLANKING_HEIGHT should check 'interlaced'
[ Upstream commit
8da7f0976b9071b528c545008de9d10cc81883b1 ]
If it is a progressive (non-interlaced) format, then ignore the
interlaced timing values.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes:
7f68127fa11f ([media] videodev2.h: defines to calculate blanking and frame sizes)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Thu, 13 Oct 2022 08:00:34 +0000 (09:00 +0100)]
media: v4l2-dv-timings: add sanity checks for blanking values
[ Upstream commit
4b6d66a45ed34a15721cb9e11492fa1a24bc83df ]
Add sanity checks to v4l2_valid_dv_timings() to ensure that the provided
blanking values are reasonable.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes:
b18787ed1ce3 ([media] v4l2-dv-timings: add new helper module)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Thu, 13 Oct 2022 14:18:46 +0000 (15:18 +0100)]
media: vivid: dev->bitmap_cap wasn't freed in all cases
[ Upstream commit
1f65ea411cc7b6ff128d82a3493d7b5648054e6f ]
Whenever the compose width/height values change, the dev->bitmap_cap
vmalloc'ed array must be freed and dev->bitmap_cap set to NULL.
This was done in some places, but not all. This is only an issue if
overlay support is enabled and the bitmap clipping is used.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes:
ef834f7836ec ([media] vivid: add the video capture and output parts)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans Verkuil [Wed, 12 Oct 2022 14:32:28 +0000 (15:32 +0100)]
media: vivid: s_fbuf: add more sanity checks
[ Upstream commit
f8bcaf714abfc94818dff8c0db84d750433984f4 ]
VIDIOC_S_FBUF is by definition a scary ioctl, which is why only root
can use it. But at least check if the framebuffer parameters match that
of one of the framebuffer created by vivid, and reject anything else.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes:
ef834f7836ec ([media] vivid: add the video capture and output parts)
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mario Limonciello [Thu, 13 Oct 2022 03:50:17 +0000 (22:50 -0500)]
PM: hibernate: Allow hybrid sleep to work with s2idle
[ Upstream commit
85850af4fc47132f3f2f0dd698b90f67906600b4 ]
Hybrid sleep is currently hardcoded to only operate with S3 even
on systems that might not support it.
Instead of assuming this mode is what the user wants to use, for
hybrid sleep follow the setting of `mem_sleep_current` which
will respect mem_sleep_default kernel command line and policy
decisions made by the presence of the FADT low power idle bit.
Fixes:
81d45bdf8913 ("PM / hibernate: Untangle power_down()")
Reported-and-tested-by: kolAflash <kolAflash@kolahilft.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216574
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dongliang Mu [Mon, 24 Oct 2022 09:02:52 +0000 (17:02 +0800)]
can: mcp251x: mcp251x_can_probe(): add missing unregister_candev() in error path
[ Upstream commit
b1a09b63684cea56774786ca14c13b7041ffee63 ]
In mcp251x_can_probe(), if mcp251x_gpio_setup() fails, it forgets to
unregister the CAN device.
Fix this by unregistering can device in mcp251x_can_probe().
Fixes:
2d52dabbef60 ("can: mcp251x: add GPIO support")
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/all/20221024090256.717236-1-dzm91@hust.edu.cn
[mkl: adjust label]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dongliang Mu [Mon, 24 Oct 2022 11:48:07 +0000 (19:48 +0800)]
can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path
[ Upstream commit
3e5b3418827cefb5e1cc658806f02965791b8f07 ]
The commit
1149108e2fbf ("can: mscan: improve clock API use") only
adds put_clock() in mpc5xxx_can_remove() function, forgetting to add
put_clock() in the error handling code.
Fix this bug by adding put_clock() in the error handling code.
Fixes:
1149108e2fbf ("can: mscan: improve clock API use")
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/all/20221024133828.35881-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rafael Mendonca [Tue, 18 Oct 2022 01:27:50 +0000 (22:27 -0300)]
drm/amdkfd: Fix memory leak in kfd_mem_dmamap_userptr()
[ Upstream commit
90bfee142af0f0e9d3bec80e7acd5f49b230acf7 ]
If the number of pages from the userptr BO differs from the SG BO then the
allocated memory for the SG table doesn't get freed before returning
-EINVAL, which may lead to a memory leak in some error paths. Fix this by
checking the number of pages before allocating memory for the SG table.
Fixes:
264fb4d332f5 ("drm/amdgpu: Add multi-GPU DMA mapping helpers")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jakub Kicinski [Fri, 21 Oct 2022 16:03:04 +0000 (09:03 -0700)]
net-memcg: avoid stalls when under memory pressure
[ Upstream commit
720ca52bcef225b967a339e0fffb6d0c7e962240 ]
As Shakeel explains the commit under Fixes had the unintended
side-effect of no longer pre-loading the cached memory allowance.
Even tho we previously dropped the first packet received when
over memory limit - the consecutive ones would get thru by using
the cache. The charging was happening in batches of 128kB, so
we'd let in 128kB (truesize) worth of packets per one drop.
After the change we no longer force charge, there will be no
cache filling side effects. This causes significant drops and
connection stalls for workloads which use a lot of page cache,
since we can't reclaim page cache under GFP_NOWAIT.
Some of the latency can be recovered by improving SACK reneg
handling but nowhere near enough to get back to the pre-5.15
performance (the application I'm experimenting with still
sees 5-10x worst latency).
Apply the suggested workaround of using GFP_ATOMIC. We will now
be more permissive than previously as we'll drop _no_ packets
in softirq when under pressure. But I can't think of any good
and simple way to address that within networking.
Link: https://lore.kernel.org/all/20221012163300.795e7b86@kernel.org/
Suggested-by: Shakeel Butt <shakeelb@google.com>
Fixes:
4b1327be9fe5 ("net-memcg: pass in gfp_t mask to mem_cgroup_charge_skmem()")
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Link: https://lore.kernel.org/r/20221021160304.1362511-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Neal Cardwell [Fri, 21 Oct 2022 17:08:21 +0000 (17:08 +0000)]
tcp: fix indefinite deferral of RTO with SACK reneging
[ Upstream commit
3d2af9cce3133b3bc596a9d065c6f9d93419ccfb ]
This commit fixes a bug that can cause a TCP data sender to repeatedly
defer RTOs when encountering SACK reneging.
The bug is that when we're in fast recovery in a scenario with SACK
reneging, every time we get an ACK we call tcp_check_sack_reneging()
and it can note the apparent SACK reneging and rearm the RTO timer for
srtt/2 into the future. In some SACK reneging scenarios that can
happen repeatedly until the receive window fills up, at which point
the sender can't send any more, the ACKs stop arriving, and the RTO
fires at srtt/2 after the last ACK. But that can take far too long
(O(10 secs)), since the connection is stuck in fast recovery with a
low cwnd that cannot grow beyond ssthresh, even if more bandwidth is
available.
This fix changes the logic in tcp_check_sack_reneging() to only rearm
the RTO timer if data is cumulatively ACKed, indicating forward
progress. This avoids this kind of nearly infinite loop of RTO timer
re-arming. In addition, this meets the goals of
tcp_check_sack_reneging() in handling Windows TCP behavior that looks
temporarily like SACK reneging but is not really.
Many thanks to Jakub Kicinski and Neil Spring, who reported this issue
and provided critical packet traces that enabled root-causing this
issue. Also, many thanks to Jakub Kicinski for testing this fix.
Fixes:
5ae344c949e7 ("tcp: reduce spurious retransmits due to transient SACK reneging")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reported-by: Neil Spring <ntspring@fb.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Tested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221021170821.1093930-1-ncardwell.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lu Wei [Fri, 21 Oct 2022 04:06:22 +0000 (12:06 +0800)]
tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
[ Upstream commit
ec791d8149ff60c40ad2074af3b92a39c916a03f ]
The type of sk_rcvbuf and sk_sndbuf in struct sock is int, and
in tcp_add_backlog(), the variable limit is caculated by adding
sk_rcvbuf, sk_sndbuf and 64 * 1024, it may exceed the max value
of int and overflow. This patch reduces the limit budget by
halving the sndbuf to solve this issue since ACK packets are much
smaller than the payload.
Fixes:
c9c3321257e1 ("tcp: add tcp_add_backlog()")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Dumazet [Mon, 15 Nov 2021 19:02:30 +0000 (11:02 -0800)]
tcp: minor optimization in tcp_add_backlog()
[ Upstream commit
d519f350967a60b85a574ad8aeac43f2b4384746 ]
If packet is going to be coalesced, sk_sndbuf/sk_rcvbuf values
are not used. Defer their access to the point we need them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of:
ec791d8149ff ("tcp: fix a signed-integer-overflow bug in tcp_add_backlog()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhang Changzhong [Fri, 21 Oct 2022 01:32:24 +0000 (09:32 +0800)]
net: lantiq_etop: don't free skb when returning NETDEV_TX_BUSY
[ Upstream commit
9c1eaa27ec599fcc25ed4970c0b73c247d147a2b ]
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fixes:
504d4721ee8e ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhengchao Shao [Thu, 20 Oct 2022 02:42:13 +0000 (10:42 +0800)]
net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
[ Upstream commit
d266935ac43d57586e311a087510fe6a084af742 ]
When the ops_init() interface is invoked to initialize the net, but
ops->init() fails, data is released. However, the ptr pointer in
net->gen is invalid. In this case, when nfqnl_nf_hook_drop() is invoked
to release the net, invalid address access occurs.
The process is as follows:
setup_net()
ops_init()
data = kzalloc(...) ---> alloc "data"
net_assign_generic() ---> assign "date" to ptr in net->gen
...
ops->init() ---> failed
...
kfree(data); ---> ptr in net->gen is invalid
...
ops_exit_list()
...
nfqnl_nf_hook_drop()
*q = nfnl_queue_pernet(net) ---> q is invalid
The following is the Call Trace information:
BUG: KASAN: use-after-free in nfqnl_nf_hook_drop+0x264/0x280
Read of size 8 at addr
ffff88810396b240 by task ip/15855
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
print_report+0x155/0x454
kasan_report+0xba/0x1f0
nfqnl_nf_hook_drop+0x264/0x280
nf_queue_nf_hook_drop+0x8b/0x1b0
__nf_unregister_net_hook+0x1ae/0x5a0
nf_unregister_net_hooks+0xde/0x130
ops_exit_list+0xb0/0x170
setup_net+0x7ac/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
Allocated by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0xa1/0xb0
__kmalloc+0x49/0xb0
ops_init+0xe7/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Freed by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x155/0x1b0
slab_free_freelist_hook+0x11b/0x220
__kmem_cache_free+0xa4/0x360
ops_init+0xb9/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes:
f875bae06533 ("net: Automatically allocate per namespace data.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>