Michal Simek [Mon, 31 May 2021 09:03:19 +0000 (11:03 +0200)]
zynqmp: Do not place u-boot to reserved memory location
TF-A and SecureOS can allocate the part of DDR for self but U-Boot is not
handling this configuration that the part of memory is reserved and
shouldn't be used by U-Boot. That's why read all reserved memory locations
and don't use it.
The code was taken from commit
4a1b975dac02 ("board: stm32mp1: reserve
memory for OP-TEE in device tree") and commit
1419e5b5167e ("stm32mp:
update MMU config before the relocation") which is used by stm32 and does
the job properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 31 May 2021 08:38:30 +0000 (10:38 +0200)]
zynqmp: Enable regulators
Enable command and fixed regulators. XDP platform is using them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 31 May 2021 07:50:01 +0000 (09:50 +0200)]
arm64: zynqmp: Update Copyright years to 2021
Trivial change for all files I have touched recently.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 31 May 2021 07:42:08 +0000 (09:42 +0200)]
arm64: zynqmp: Add label for zynqmp_ipi
Add label which is used by bootloader for adding bootloader specific flag.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/3dc8416abdd3498e61edcd83830a12af295c5c6d.1611224800.git.michal.simek@xilinx.com
Michal Simek [Thu, 27 May 2021 11:44:35 +0000 (13:44 +0200)]
arm64: zynqmp: Move DP nodes to the end of file (zcu106)
Just sync it with others for easier comparison.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 27 May 2021 11:49:05 +0000 (13:49 +0200)]
arm64: zynqmp: Add reset description for sata
Sata needs to get reset before configuration that's why add property for it
there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stefano Stabellini [Wed, 5 May 2021 21:18:21 +0000 (14:18 -0700)]
arm64: zynqmp: Add missing SMID for pcie to zynqmp.dtsi
The SMMU is disabled in device tree so this change has no impact.
The benefit is that this way it is in sync with xen.dtsi. Xen enables
the SMMU and makes use of it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Michal Simek [Mon, 11 May 2020 08:14:34 +0000 (10:14 +0200)]
arm64: zynqmp: Disable CCI by default
There is no reason to have CCI no enabled by default. Enable it when your
system configuration requires it. In Xilinx configuration flow this is
work for Device Tree Generator which reads information from HW Design
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 31 May 2021 07:56:58 +0000 (09:56 +0200)]
arm64: zynqmp: Update psgtr clocks index for boards
Update the psgtr clock indexing for couple of zynqmp boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 19 May 2021 13:16:19 +0000 (15:16 +0200)]
arm64: zynqmp: Handle MMC seq number based on boot device
K26 has EMMC and SD and default 0 is not working when system is booting out
of SD which is controller 1. Add controller autodetection via
mmc_get_env_dev(). The same code is used for distro_boot selection done in
board_late_init(). bootseq variable can't be reused because this is called
so late.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 19 May 2021 11:02:20 +0000 (13:02 +0200)]
arm64: zynqmp: Add psu_init_gpl for k26 boards
Add psu_init_gpl file for getting SPL to work directly from the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 26 Nov 2020 13:25:01 +0000 (14:25 +0100)]
ARM: zynq: Rename bus to be align with simple-bus yaml
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI
point-to-point channels for communicating addresses, data, and response
transactions between master and slave clients. This ARM AMBA 3.0..."
Issues are reported as:
.. amba: $nodename:0: 'amba' does not match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
>From schema:
../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml
Similar change has been done for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
Michal Simek [Tue, 11 May 2021 11:59:01 +0000 (13:59 +0200)]
arm64: zynqmp: Enable gpio driver for zcu1275/zcu1285
Enable gpio driver on these boards. GPIOs can be used on any board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 5 Oct 2020 07:35:40 +0000 (09:35 +0200)]
arm64: zynqmp: Add support for SVD devices
SVDs are using different name which can't be handled via zynqmp_devices
structure. That's why introduce zynqmp_detect_svd_name() which checks ID
code for these devices and show proper name for them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 13 May 2021 11:58:58 +0000 (13:58 +0200)]
arm64: zynqmp: Enable EFI secure boot
Enabling EFI secure boot which is required for EBBR specification.
Enabling this will fix
"RT.SetVariable - Create one Time Base Auth Variable, the expect return
status should be EFI_SUCCESS"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
T Karthik Reddy [Thu, 29 Apr 2021 14:02:30 +0000 (08:02 -0600)]
arm64: xilinx: Set CONFIG_ZYNQMP_FIRMWARE config for mini emmc
CONFIG_ZYNQMP_FIRMWARE enables zynqmp firmware driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Ashok Reddy Soma [Thu, 15 Apr 2021 11:12:15 +0000 (05:12 -0600)]
arm64: zynqmp: Fix application loading on R5 core1
From U-Boot, loading application on RPU core 0 is fine but loading on
core 1 is not handled properly. Lock-step mode needs both the R5 cores
to be initialized and it is working fine. Whereas in SPLIT mode individual
R5 cores needs to be initialized as they need to execute differenet
applications. Handle both these lock-step and split modes by propagating
mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions
and by adding conditions in those functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 26 Nov 2020 13:25:03 +0000 (14:25 +0100)]
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
The Linux commit
f69629919942 ("dt-bindings: sram: Convert SRAM bindings to
json-schema") converted binding to yaml and some missing required
properties started to be reported. Align binding based on it.
The patch is fixing these warnings:
.../zynq-zc702.dt.yaml: sram@
fffc0000: '#address-cells' is a required property
.../zynq-zc702.dt.yaml: sram@
fffc0000: '#size-cells' is a required property
.../zynq-zc702.dt.yaml: sram@
fffc0000: 'ranges' is a required property
>From schema: .../Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
Michal Simek [Thu, 26 Nov 2020 13:25:04 +0000 (14:25 +0100)]
ARM: zynq: Convert at25 binding to new description on zc770-xm013
The Linux commit
f8f79fa6bb25 ("dt-bindings: at25: convert the binding
document to yaml") converted binding to yaml and 3 deprecated properties
pop up.
The patch is fixing these warnings:
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property
>From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml
by converting them to new binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
Jorge Ramirez-Ortiz [Sun, 13 Jun 2021 18:55:53 +0000 (20:55 +0200)]
zynqmp: spl: support DRAM ECC initialization
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid
spurious ECC errors that can occur when accessing unitialized memory.
The feature is enabled by setting the option
CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data:
SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex)
SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex)
Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 2 Jun 2021 10:40:45 +0000 (12:40 +0200)]
gpio: pca953x: Add missing i2c dependency
pca953x also depends on i2c that's why add dependency to Kconfig.
Where GPIO is enabled but I2C compilation error pops up.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Bin Meng [Mon, 21 Jun 2021 23:33:21 +0000 (07:33 +0800)]
azure: Use msys2
20210604 installer for Windows build
MSYS2 Windows build started to fail since yesterday (Jun 21):
checking keyring...
checking package integrity...
error: gcc-libs: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-libs-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: gcc: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: failed to commit transaction (invalid or corrupted package)
Errors occurred, no packages were upgraded.
Switching to the latest installer (version
20210604) seems to fix it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 18 Jun 2021 15:18:56 +0000 (11:18 -0400)]
Merge branch 'network_master' of https://source.denx.de/u-boot/custodians/u-boot-net
Tim Harvey [Thu, 17 Jun 2021 23:08:54 +0000 (16:08 -0700)]
net: octeontx: smi: use dt live tree API
clean up octeontx_smi_probe by using the live-tree API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Dimitri John Ledkov [Wed, 21 Apr 2021 11:42:01 +0000 (12:42 +0100)]
cmd: pxe_utils: sysboot: fix crash if either board or soc are not set.
If the environment does not have "soc" or "board" set, and fdtdir
option is specified in extlinux.conf, the bootloader will crash whilst
dereferencing a null pointer. Add a guard against null soc or
board. Fixes a crash of qemu-riscv64_smode configuration, which does
not have CONFIG_SYS_SOC defined.
Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Michael Walle [Thu, 25 Feb 2021 15:51:11 +0000 (16:51 +0100)]
net: use the same alias stem for ethernet as linux
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from
the linux tree:
$ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l
0
$ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l
633
In u-boot device trees both prefixes are used. Until recently the only
user of the ethernet alias was the sandbox test device tree. This
changed with commit
fc054d563bfb ("net: Introduce DSA class for Ethernet
switches"). There, the MAC addresses are inherited based on the devices
sequence IDs which is in turn given by the device tree.
Before there are more users in u-boot and both worlds will differ even
more, rename the alias prefix to "ethernet" to match the linux ones.
Also adapt the test cases and rename any old aliases in the u-boot
device trees.
Cc: David Wu <david.wu@rock-chips.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Michael Walle [Wed, 24 Feb 2021 16:30:44 +0000 (17:30 +0100)]
net: use a more deterministic approach to get the active ethernet device
If the environment variable "ethact" is not set, the first device in the
uclass is returned. This depends on the probing order of the ethernet
devices. Moreover it is not not configurable at all.
Try to return the ethernet device with sequence id 0 first which then
can be configured by the aliases in a device tree. Fall back to the old
mechanism in case of an error.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Heinrich Schuchardt [Thu, 3 Jun 2021 07:52:41 +0000 (07:52 +0000)]
net: sun8i-emac: fix MDIO frequency
Commit
4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency") leads to
network failure on the OrangePi PC.
=> dhcp
sun8i_emac_eth_start: Timeout
According to the commit message the change of the MDIO frequency is only
required for external PHYs.
Fixes:
4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Jassi Brar [Fri, 4 Jun 2021 09:44:38 +0000 (18:44 +0900)]
net: synquacer: Add netsec driver
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Daniil Stas [Sun, 30 May 2021 13:34:09 +0000 (13:34 +0000)]
net: dwc_eth_qos: Revert some changes of commit
3a97da12ee7b
Revert some changes of commit
3a97da12ee7b ("net: dwc_eth_qos: add dwc
eqos for imx support") that were probably added by mistake.
One of these changes can lead to received data corruption (enabling
FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings
for some platforms. And another makes some writes at unknown memory
location.
Fixes:
3a97da12ee7b ("net: dwc_eth_qos: add dwc eqos for imx support")
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ye Li <ye.li@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Daniil Stas [Sun, 23 May 2021 22:24:48 +0000 (22:24 +0000)]
net: dwc_eth_qos: Fix needless phy auto-negotiation restarts
Disabling clk_ck clock leads to link up status loss in phy, which
leads to auto-negotiation restart before each network command
execution.
This issue is especially big for PXE boot protocol because of
auto-negotiation restarts before each configuration filename trial.
To avoid this issue don't disable clk_ck clock after it was enabled.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tim Harvey [Fri, 16 Apr 2021 20:25:09 +0000 (13:25 -0700)]
net: e1000: do not attempt to set hwaddr for i210 without FLASH
commit
f1bcad22dd19 ("net: e1000: add support for writing to EEPROM")
adds support for storing hwaddr in EEPROM however i210 devices do not
support this and thus results in errors such as:
Warning: e1000#0 failed to set MAC address'
Check if a flash device is present and if not return -ENOSYS indicating
this is not supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Hou Zhiqiang [Sat, 12 Jun 2021 18:15:41 +0000 (21:15 +0300)]
Fix a memory leak issue in the RX port initialization.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tom Rini [Thu, 17 Jun 2021 12:44:56 +0000 (08:44 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release,
mmc, usb, env, etc for Layerscape boards
- powerpc: Update Maintainers for some boards.
Tom Rini [Thu, 17 Jun 2021 12:44:23 +0000 (08:44 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-riscv
- ae350 related dts fixes.
Priyanka Jain [Thu, 17 Jun 2021 07:22:46 +0000 (12:52 +0530)]
board: freescale: t1028xrdb: Add MAINTAINER for revD
Add Priyanka Jain as MAINTAINER for
T2080RDB_revD_defconfig,
T2080RDB_revD_NAND_defconfig,
T2080RDB_revD_SDCARD_defconfig and
T2080RDB_revD_SPIFLASH_defconfig
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Ran Wang [Wed, 16 Jun 2021 12:23:19 +0000 (17:53 +0530)]
armv8: Update erratum number to align with doc
Change the USB erratum number A-050106 to A-050204 as A-050106 is
a duplicate and never be published.
Fixes
0cfa00cdb94 (“armv8: Add workaround for USB erratum A-050106”)
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Fri, 11 Jun 2021 12:28:08 +0000 (15:28 +0300)]
board: freescale: t208xrdb: add a config option for rev D dts fixups
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.
This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.
Defconfig files with the option enable explicitly are added for
convenience.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Wed, 16 Jun 2021 12:17:31 +0000 (17:47 +0530)]
board: freescale: t208xrdb: add Linux fdt fix-ups for rev D
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Fri, 11 Jun 2021 12:28:06 +0000 (15:28 +0300)]
board: freescale: t208xrdb: detect the board revision version
Detect and print the board revision version based on the CPLD registers.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Fri, 11 Jun 2021 12:28:05 +0000 (15:28 +0300)]
board: freescale: t208xrdb: remove the legacy non-DM_ETH code
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the
board_eth_init() callback and the non-DM_ETH code paths since they are not
needed anymore.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:25:21 +0000 (14:25 +0000)]
pg-wcom-ls102xa: fix sys counter frequency
A system clock of 66MHz was chosen for the pg-wcom-ls102xa.
Compared to the Evalboard, this corresponds to a reduction of 1/3.
The system counter clock should have been reduced accordingly,
but that was not the case, so we had a system time that was
1/3 behind the real time.
This patch corrects the system counter clock to
8.333MHz = 66.667MHz / 8.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:24:32 +0000 (14:24 +0000)]
pg-wcom-ls102x: initialize front led and app buf
This patch adds the front led initialization and the application
buffer enable to the eraly board inititlaization.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:23:34 +0000 (14:23 +0000)]
km: ls102x: update device disable configuration acc hw design desc
In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.
This patch uses available hwconfig option for updating ls102x device
disable configuration.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:21:15 +0000 (14:21 +0000)]
km: ls102x: set ethrotate envvar to no
The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.
For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.
Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:20:13 +0000 (14:20 +0000)]
km/scripts: fix saveenv command syntax
This is most probably a typo, and in older u-uboot versions is same as
'saveenv', in the newer uboot versions there is a separate 'save' command
that is different from 'saveenv'.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:19:08 +0000 (14:19 +0000)]
km: ls102xa: add missing define for PRAM regions
In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:17:34 +0000 (14:17 +0000)]
km/ls102xa: add support for u-boot POST memory test
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:16:28 +0000 (14:16 +0000)]
board/km: add support for expu1 design based on nxp
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:07:01 +0000 (13:37 +0530)]
board: freescale: t102xrdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t102xrdb board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:07:00 +0000 (13:37 +0530)]
board: freescale: p2041rdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p2041rdb board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:06:59 +0000 (13:36 +0530)]
board: freescale: p1_p2_rdb_pc: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p1_p2_rdb_pc board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:06:58 +0000 (13:36 +0530)]
board: freescale: t4rdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t4rdb board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Lasse Klok Mikkelsen [Tue, 8 Jun 2021 06:39:12 +0000 (08:39 +0200)]
arm: dts: ls1021a.dtsi: Fix invalid reg on gpio nodes
Address and size cells on SOC are set to 1. But gpio nodes are specified
with 2 cells. This fixes the gpio nodes to correct cells.
Signed-off-by: Lasse Klok Mikkelsen <lkmi@prevas.dk>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Fri, 4 Jun 2021 13:40:58 +0000 (13:40 +0000)]
net: tsec: add option to set device max-speed via dts
Current tsec adapter sets adapter gigabit capabilities by default, and in
reality this must not always be the case.
It is possible that tsec adapter is used for 100Mbps connection, and in
this case setting 1000Mbps capabilities can lead to some side effects such
longer autoneg process.
In our ls102x designs this problem leads to long autoneg times (> 4 sec)
in case board rgmii link is 100Mbps capable only.
Limiting the rgmii link capabilities provides faster and smoother
link establishment.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Fri, 4 Jun 2021 09:25:00 +0000 (09:25 +0000)]
keymile: common: fix hexadecimal env variable format
Commit df86d32 breaks linux kernel and product application boot.
Linux kernel and our product application scripts are expecting 0x prefix
for hexadecimal values, while env_set_hex writes them without a prefix.
This patch partially revert env_set_hex usage for affected env variables.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Fri, 4 Jun 2021 09:17:56 +0000 (09:17 +0000)]
configs: seli8: set envsize to 0x4000
During the mainlining of the board this was by mistake set to sector size.
Our user space env scripts are expecting envsize of 0x4000, and setting
this differently will break our cross-platform compatibility.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Thu, 3 Jun 2021 02:51:19 +0000 (10:51 +0800)]
armv8: layerscape: drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Thu, 3 Jun 2021 02:51:18 +0000 (10:51 +0800)]
mmc: fsl_esdhc_imx: drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
There is no i.MX board using such option. Drop it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Thu, 3 Jun 2021 02:51:17 +0000 (10:51 +0800)]
mmc: fsl_esdhc: convert to CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.
This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.
Fixes:
52faec31827e ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Matt Merhar [Sun, 30 May 2021 00:16:17 +0000 (00:16 +0000)]
board: freescale: p2041rdb: use correct EEPROM address length
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Fri, 21 May 2021 07:15:06 +0000 (15:15 +0800)]
configs: ls2088aqds: fix synchronous exception
IFC NOR flash base address of ls2088a is 0x580000000,
and offset of env crc is 0x500000, so fix the macro
CONFIG_ENV_ADDR to fix synchronous exception(access illegal address)
Fixes:
59071804c1 ("configs: ls2080a: Correct ENV_ADDR value")
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Wed, 19 May 2021 11:10:12 +0000 (16:40 +0530)]
configs: ls1088a: Enable CONFIG_SYS_RELOC_ENV_ADDR
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Fri, 14 May 2021 02:33:57 +0000 (10:33 +0800)]
arm: dts: lx2162aqds: support eMMC HS400 mode on esdhc1
Add properties related to eMMC HS400 mode for esdhc1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 13 May 2021 06:54:32 +0000 (14:54 +0800)]
pci: layerscape-ep: Add check of the PCIe controller enablement
Stop to initialize the PCIe controller if it's disabled by RCW.
Fixes:
118e58e26eba ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Chaitanya Sakinam [Fri, 7 May 2021 04:22:05 +0000 (12:22 +0800)]
armv8: ls1012a: Pass PPFE firmware to Linux through FDT
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Tue, 27 Apr 2021 08:42:11 +0000 (16:42 +0800)]
armv8: layerscape: enable eMMC HS400 workarounds for LX2160A/LX2162A
Enable eMMC HS400 workarounds for LX2160A/LX2162A.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Jiafei Pan [Wed, 21 Apr 2021 04:12:49 +0000 (12:12 +0800)]
armv8: layerscape: add PSCI support for cpu release
For cpu release command, check whether PSCI is supported firstly,
if supported, use PSCI to kick off secondary cores, otherwise still
use spin table.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
[Fixed checkpatch alignment CHECKs]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Singh [Mon, 19 Apr 2021 05:45:04 +0000 (11:15 +0530)]
board: freescale: vid.c: Add check for return value of adjust_vdd()
Add check for return value of adjust_vdd()
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Bin Meng [Tue, 15 Jun 2021 05:45:57 +0000 (13:45 +0800)]
riscv: andes_plic: Fix riscv_get_ipi() mask
Current logic in riscv_get_ipi() for Andes PLICSW does not look
correct. The mask to test IPI pending bits for a hart should be
left shifted by (8 * gd->arch.boot_hart), just the same as what
is done in riscv_send_ipi().
Fixes:
8b3e97badf97 ("riscv: add functions for reading the IPI status")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 23:00:30 +0000 (07:00 +0800)]
riscv: ae350: doc: Remove CONFIG_SKIP_LOWLEVEL_INIT
The doc says CONFIG_SKIP_LOWLEVEL_INIT is in ax25-ae350.h, while
actually it is not. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:13 +0000 (13:51 +0800)]
riscv: ae350: dts: Add missing "u-boot, dm-spl" for SPL config
At present the AE350 SPL defconfig is using OF_PRIOR_STAGE. The
intention was to use gdb to load device tree before running U-Boot
SPL/proper from RAM. When we switch to OF_SEPARATE we will have to
use our own DT but without "u-boot,dm-spl" in several essential
nodes, SPL does not boot.
Let's add all the required "u-boot,dm-spl" for SPL config.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:12 +0000 (13:51 +0800)]
riscv: ae350: dts: Fix #interrupt-cells for plic0 in 32-bit
All the device nodes that refer to plic0 as their interrupt parent
have 2 cells encoded in their interrupts property, but plic0 only
provides 1 cell in #interrupt-cells which is incorrect.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:11 +0000 (13:51 +0800)]
riscv: ae350: dts: Remove the unnecessary #address-cells in plic nodes
PLIC nodes don't have child nodes, so #address-cells is not needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:10 +0000 (13:51 +0800)]
riscv: ae350: dts: Remove the unnecessary space in bootargs
There are two spaces before "debug' in bootargs. Drop one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:09 +0000 (13:51 +0800)]
riscv: ae350: dts: Add SPDX license header
The SPDX license header is currently missing. Add one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tom Rini [Wed, 16 Jun 2021 15:18:11 +0000 (11:18 -0400)]
Merge tag 'u-boot-imx-
20210616' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-
20210616
-------------------
- imxrt : fixes, USB, imxrt1020-evk
- imx8m:
fix for verdin-imx8mm
Add conga-QMX8 board
- imx6 :
documentation for pico-imx6:
Add SeeedStudio NPI-IMX6ULL Support
ventana: DM PCI
- imx7d:
added SMEGW01 board
CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765
Mian Yousaf Kaukab [Wed, 14 Apr 2021 10:33:58 +0000 (12:33 +0200)]
ls1012a: net: pfe: remove pfe stop from bootcmd
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Tue, 13 Apr 2021 15:54:17 +0000 (17:54 +0200)]
board: sl28: fix RGMII clock and voltage
It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.
Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Manish Tomar [Tue, 13 Apr 2021 07:08:34 +0000 (12:38 +0530)]
configs: ls1046afrwy: Add secure boot config
Add required CONFIG_NXP_ESBC for ls1046afrwy to enable ESBC Chain of Trust.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Tom Rini [Tue, 15 Jun 2021 12:23:04 +0000 (08:23 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- Turris: Fix bootcmd_rescue (Pali)
Pali Rohár [Mon, 14 Jun 2021 14:45:58 +0000 (16:45 +0200)]
arm: mvebu: turris_{omnia, mox}: ensure running bootcmd_rescue always works
One of the points of putting the rescue boot command into default
environment is that user can invoke it without physical access to the
board (without having to press the factory reset button), by running
run bootcmd_rescue
in U-Boot's console.
Therefore we have to ensure that bootcmd_rescue is always set to default
value, regardless of whether the factory reset button was pressed.
Otherwise the variable will be empty for example after upgrade from
previous U-Boot.
Fixes:
ec3784d62646 ("arm: mvebu: turris_mox: add support for board rescue mode")
Fixes:
176c3e7760a2 ("arm: mvebu: turris_omnia: support invoking rescue boot from console")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Fri, 11 Jun 2021 12:29:34 +0000 (08:29 -0400)]
Merge tag 'xilinx-for-v2021.07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.07-rc5
zynqmp:
- Fix ANALOG_BUS value after powerup
- Disable EFI_CAPSULE_ON_DISK_EARLY
zynqmp-gqspi:
- Fix write issue
Michal Simek [Thu, 10 Jun 2021 12:33:55 +0000 (14:33 +0200)]
arm64: zynqmp: Disable EFI_CAPSULE_ON_DISK_EARLY
Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.
EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ashok Reddy Soma [Tue, 25 May 2021 12:36:27 +0000 (06:36 -0600)]
spi: zynqmp_gqspi: Fix write issue
Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.
Add dummy write to genfifo register in chipselect.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Adrian Fiergolski [Tue, 8 Jun 2021 10:37:23 +0000 (12:37 +0200)]
arm64: zynqmp: Writing correct value to ANALOG_BUS
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("
056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Thu, 10 Jun 2021 17:27:14 +0000 (13:27 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- mvebu: Turris MOX misc updates (cmds, rescue mode, LED's etc)
(Marek)
- mvebu: correct Armada 8K addresses (Heinrich)
Heinrich Schuchardt [Tue, 8 Jun 2021 10:00:35 +0000 (12:00 +0200)]
arm64: mvebu: correct Armada 8K addresses
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:51 +0000 (16:34 +0200)]
arm: mvebu: turris_mox: enable options for Turris network boot
Enable configuration options to support Turris network boot. This
includes FIT support and some crypto commands.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:50 +0000 (16:34 +0200)]
arm: mvebu: dts: turris_mox: add nodes for SPI NOR partitions
Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:49 +0000 (16:34 +0200)]
arm: mvebu: configs: turris_mox: add fdtfile default env variable
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:48 +0000 (16:34 +0200)]
arm: mvebu: turris_mox: start blinking PHY LEDs when entering rescue
Configure blinking on ethernet PHY LEDs on the MOX A board when entering
rescue mode via reset button.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:47 +0000 (16:34 +0200)]
arm: mvebu: turris_mox: add support for board rescue mode
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 7 Jun 2021 14:34:46 +0000 (16:34 +0200)]
arm: mvebu: dts: turris_mox: add button and LED nodes
Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Joao Marcos Costa [Mon, 17 May 2021 21:20:38 +0000 (18:20 -0300)]
fs/squashfs: fix reading of fragmented files
The fragmented files were not correctly read because of two issues:
- The squashfs_file_info struct has a field named 'comp', which tells if
the file's fragment is compressed or not. This field was always set to
'true' in sqfs_get_regfile_info and sqfs_get_lregfile_info. It should
actually take sqfs_frag_lookup's return value. This patch addresses
these two assignments.
- In sqfs_read, the fragments (compressed or not) were copied to the
output buffer through a for loop which was reading data at the wrong
offset. Replace these loops by equivalent calls to memcpy, with the
right parameters.
I tested this patch by comparing the MD5 checksum of a few fragmented
files with the respective md5sum output in sandbox, considering both
compressed and uncompressed fragments.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tom Rini [Wed, 9 Jun 2021 12:20:36 +0000 (08:20 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
- dwc2 and cdns3 fixes
Tom Rini [Wed, 9 Jun 2021 12:20:24 +0000 (08:20 -0400)]
Merge tag 'efi-2021-07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc5
Documentation:
* pinmux and ums man-page
Bug fixes:
* Consider that partition numbers as hexadecimal.
* Avoid a possible NULL dereference in efi_capsule_delete_file().
Fabio Estevam [Fri, 28 May 2021 13:26:57 +0000 (10:26 -0300)]
mx7d: Add Storopack's SMEGW01 board
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Andrey Zhizhikin [Sun, 2 May 2021 14:32:37 +0000 (16:32 +0200)]
imx8mn: configs: add support for distro boot commands
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Navin Sankar Velliangiri [Tue, 18 May 2021 03:33:20 +0000 (09:03 +0530)]
imx: Add SeeedStudio NPI-IMX6ULL Support
CPU: Freescale i.MX6ULL rev1.1 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 49C
Reset cause: POR
Model: Seeed NPi iMX6ULL Dev Board with NAND
Board: Seeed NPi i.MX6ULL Dev Board
DRAM: 512 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>
Note:
Changes in v2:
* removed unnecessary space in imx6ull-seeed-npi-imx6ull-dev-board.dts file.
* Used SZ_2M for CONFIG_SYS_MALLOC_LEN size allocation.