review.tizen.org Git - platform/kernel/linux-rpi.git/log

ath11k: dp_rx: fix monitor status dma unmap direction

After enabling CONFIG_DMA_API_DEBUG there was a warning about using
dma_unmap_single() in wrong direction from ath11k_dp_rx_process_mon_status().

[  140.279477] ------------[ cut here ]------------
[  140.279908] DMA-API: ath11k_pci 0000:06:00.0: device driver syncs DMA memory with different direction [device address=0x00000000fac08a40] [size=2176 bytes] [mapped with DMA_FROM_DEVICE] [s
[  140.279925] WARNING: CPU: 7 PID: 97 at kernel/dma/debug.c:1120 check_sync+0x494/0x730
[  140.279939] Modules linked in: ath11k_pci ath11k mac80211 libarc4 cfg80211 qmi_helpers qrtr_mhi mhi qrtr ns nvme nvme_core
[  140.279958] CPU: 7 PID: 97 Comm: kworker/u16:1 Not tainted 5.10.0-rc4+ #262
[  140.279968] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0049.2018.0801.1601 08/01/2018
[  140.279995] Workqueue: phy0 ieee80211_scan_work [mac80211]
[  140.280009] RIP: 0010:check_sync+0x494/0x730
[  140.280022] Code: 8b 4c 24 10 4c 8b 44 24 18 4c 8b 54 24 20 48 89 c6 4c 89 54 24 10 4c 89 f9 4c 89 ea 48 c7 c7 40 b9 74 9c 41 56 e8 2f a0 ab 00 <0f> 0b 48 89 ef e8 e5 17 ac 00 41 58 4c 8b
[  140.280033] RSP: 0018:ffff9f588024cbd8 EFLAGS: 00010086
[  140.280046] RAX: 0000000000000000 RBX: ffff9f588024cc40 RCX: ffff8eed18dd9f98
[  140.280057] RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff8eed18dd9f90
[  140.280067] RBP: ffff8eebc1407800 R08: 00000000ffffffea R09: 0000000000000000
[  140.280082] R10: 0000000000000003 R11: 3fffffffffffffff R12: ffffffff9e081060
[  140.280093] R13: ffff8eebc43908b0 R14: ffffffff9c74c104 R15: 00000000fac08a40
[  140.280104] FS:  0000000000000000(0000) GS:ffff8eed18c00000(0000) knlGS:0000000000000000
[  140.280115] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  140.280127] CR2: 00007f6feafb12a0 CR3: 00000001604ca001 CR4: 00000000003706e0
[  140.280138] Call Trace:
[  140.280149]  <IRQ>
[  140.280161]  debug_dma_sync_single_for_cpu+0x79/0x80
[  140.280173]  ? mark_held_locks+0x50/0x80
[  140.280185]  ? lockdep_hardirqs_on_prepare.part.0+0x65/0x130
[  140.280197]  ? __local_bh_enable_ip+0x6f/0xb0
[  140.280215]  ? ath11k_dp_rx_reap_mon_status_ring+0x202/0x340 [ath11k]
[  140.280231]  ath11k_dp_rx_reap_mon_status_ring+0x22c/0x340 [ath11k]
[  140.280249]  ? ath11k_dp_rx_process_mon_rings+0x1a0/0x1a0 [ath11k]
[  140.280265]  ath11k_dp_rx_process_mon_status+0x83/0x3c0 [ath11k]
[  140.280278]  ? __lock_acquire+0x3bd/0x6d0
[  140.280296]  ? ath11k_dp_rx_process_mon_rings+0x1a0/0x1a0 [ath11k]
[  140.280311]  ? ath11k_dp_rx_process_mon_rings+0x1a0/0x1a0 [ath11k]
[  140.280326]  ? ath11k_hw_mac_id_to_srng_id_qca6390+0x10/0x10 [ath11k]
[  140.280341]  ? ath11k_dp_rx_process_mon_rings+0x4a/0x1a0 [ath11k]
[  140.280353]  ? timer_fixup_init+0x30/0x30
[  140.280367]  ? ath11k_dp_rx_process_mon_rings+0x1a0/0x1a0 [ath11k]
[  140.280385]  ath11k_dp_service_mon_ring+0x2b/0x50 [ath11k]
[  140.280400]  ? ath11k_dp_rx_process_mon_rings+0x1a0/0x1a0 [ath11k]
[  140.280413]  call_timer_fn+0xb1/0x2d0
[  140.280426]  __run_timers.part.0+0x205/0x2f0
[  140.280439]  run_timer_softirq+0x21/0x50
[  140.280450]  __do_softirq+0xc2/0x454
[  140.280463]  asm_call_irq_on_stack+0x12/0x20
[  140.280476]  </IRQ>
[  140.280488]  do_softirq_own_stack+0x56/0x60
[  140.280500]  irq_exit_rcu+0x9a/0xd0
[  140.280511]  sysvec_apic_timer_interrupt+0x43/0xa0
[  140.280526]  asm_sysvec_apic_timer_interrupt+0x12/0x20
[  140.280540] RIP: 0010:_raw_spin_unlock_irqrestore+0x25/0x40
[  140.280551] Code: 80 00 00 00 00 55 48 89 fd 48 83 c7 18 53 48 89 f3 48 8b 74 24 10 e8 ca 8f 4b ff 48 89 ef e8 22 dc 4b ff f6 c7 02 75 0c 53 9d <65> ff 0d 04 51 20 64 5b 5d c3 e8 9c 08 56
[  140.280563] RSP: 0018:ffff9f58802e7878 EFLAGS: 00000246
[  140.280578] RAX: 00000000000435ef RBX: 0000000000000246 RCX: 0000000000000040
[  140.280592] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff9be13e84
[  140.280603] RBP: ffff8eed18dde480 R08: 0000000000000001 R09: ffff8eebc2292760
[  140.280614] R10: 0000000000000005 R11: ffff8eebc2292760 R12: 0000000000000000
[  140.280625] R13: ffff9f58802e7900 R14: ffff8eed18dde480 R15: ffff8eed18dde480
[  140.280637]  ? _raw_spin_unlock_irqrestore+0x34/0x40
[  140.280649]  __mod_timer+0x274/0x400
[  140.280661]  ? wait_for_completion_timeout+0x76/0x110
[  140.280675]  schedule_timeout+0xa8/0x140
[  140.280687]  ? __next_timer_interrupt+0x100/0x100
[  140.280698]  wait_for_completion_timeout+0xa2/0x110
[  140.280714]  ath11k_start_scan+0x4c/0xf0 [ath11k]
[  140.280730]  ath11k_mac_op_hw_scan+0x1e9/0x2c0 [ath11k]
[  140.280763]  drv_hw_scan+0x79/0x260 [mac80211]
[  140.280789]  __ieee80211_scan_completed+0x379/0x440 [mac80211]
[  140.280816]  ieee80211_scan_work+0x12f/0x330 [mac80211]
[  140.280830]  process_one_work+0x279/0x5b0
[  140.280842]  worker_thread+0x49/0x300
[  140.280854]  ? process_one_work+0x5b0/0x5b0
[  140.280868]  kthread+0x135/0x150
[  140.280880]  ? __kthread_bind_mask+0x60/0x60
[  140.280891]  ret_from_fork+0x22/0x30
[  140.280903] irq event stamp: 275961
[  140.280918] hardirqs last  enabled at (275960): [<ffffffff9b270f1f>] __local_bh_enable_ip+0x6f/0xb0
[  140.280931] hardirqs last disabled at (275961): [<ffffffff9be13ca3>] _raw_spin_lock_irqsave+0x63/0x80
[  140.280946] softirqs last  enabled at (275944): [<ffffffffc055288d>] ath11k_ce_send+0x14d/0x260 [ath11k]
[  140.280958] softirqs last disabled at (275953): [<ffffffff9c000f72>] asm_call_irq_on_stack+0x12/0x20
[  140.280971] ---[ end trace 31cb94e18d401398 ]---

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606156046-24764-1-git-send-email-kvalo@codeaurora.org

wcn36xx: Send NULL data packet when exiting BMPS

This commit updates the BMPS exit path to be consistent with downstream in
terms of exiting BMPS mode. Downstream sets the flag to send a NULL data
frame to the host on exiting BMPS.

This will tell the AP to send any queued frames to the STA immediately.
Verified the relevant bit toggle in wireshark.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201120021403.2646574-2-bryan.odonoghue@linaro.org

ath10k: Constify static qmi structs

qmi_msg_handler[] and ath10k_qmi_ops are only used as input arguments
to qmi_handle_init() which accepts const pointers to both qmi_ops and
qmi_msg_handler. Make them const to allow the compiler to put them in
read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122234031.33432-3-rikard.falkeborn@gmail.com

ath10k: Release some resources in an error handling path

Should an error occur after calling 'ath10k_usb_create()', it should be
undone by a corresponding 'ath10k_usb_destroy()' call

Fixes: 4db66499df91 ("ath10k: add initial USB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122170358.1346065-1-christophe.jaillet@wanadoo.fr

ath10k: Fix an error handling path

If 'ath10k_usb_create()' fails, we should release some resources and report
an error instead of silently continuing.

Fixes: 4db66499df91 ("ath10k: add initial USB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122170342.1346011-1-christophe.jaillet@wanadoo.fr

ath10k: Fix the parsing error in service available event

The wmi service available event has been
extended to contain extra 128 bit for new services
to be indicated by firmware.

Currently the presence of any optional TLVs in
the wmi service available event leads to a parsing
error with the below error message:
ath10k_snoc 18800000.wifi: failed to parse svc_avail tlv: -71

The wmi service available event parsing should
not return error for the newly added optional TLV.
Fix this parsing for service available event message.

Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00720-QCAHLSWMTPL-1

Fixes: cea19a6ce8bf ("ath10k: add WMI_SERVICE_AVAILABLE_EVENT support")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605501291-23040-1-git-send-email-pillair@codeaurora.org

ath11k: Fix an error handling path

If 'kzalloc' fails, we must return an error code.

While at it, remove a useless initialization of 'err' which could hide the
issue.

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201122173943.1366167-1-christophe.jaillet@wanadoo.fr

ath11k: Build check size of ath11k_skb_cb

It is rather easy to add more entries to ath11k_skb_cb while forgetting the
size limit of ieee80211_tx_info->driver_data. So just check this during the
build to reduce the change of accidental buffer overflow in the skbuff->cb.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-3-sven@narfation.org

ath11k: Reset ath11k_skb_cb before setting new flags

It was observed that the codepath for the ATH11K_SKB_HW_80211_ENCAP was
used even when the IEEE80211_TX_CTRL_HW_80211_ENCAP was not enabled for a
an skbuff. This became even more prominent when the QCAs wlan-open patchset
for ath11k [1] was applied and a sane looking fix just caused crashes when
injecting frames via a monitor interface (for example with ratechecker):

  [   86.963152] Unable to handle kernel NULL pointer dereference at virtual address 00000338
  [   86.963192] pgd = ffffffc0008f0000
  [   86.971034] [00000338] *pgd=0000000051706003, *pud=0000000051706003, *pmd=0000000051707003, *pte=00e800000b000707
  [   86.984292] Internal error: Oops: 96000006 [#1] PREEMPT SMP
  [...]
  [   87.713339] [<ffffffbffc802480>] ieee80211_tx_status_8023+0xf8/0x220 [mac80211]
  [   87.715654] [<ffffffbffc98bad4>] ath11k_dp_tx_completion_handler+0x42c/0xa10 [ath11k]
  [   87.722924] [<ffffffbffc989190>] ath11k_dp_service_srng+0x70/0x3c8 [ath11k]
  [   87.730831] [<ffffffbffca03460>] 0xffffffbffca03460
  [   87.737599] [<ffffffc00046ef58>] net_rx_action+0xf8/0x288
  [   87.742462] [<ffffffc000097554>] __do_softirq+0xfc/0x220
  [   87.748014] [<ffffffc000097900>] irq_exit+0x98/0xe8
  [   87.753396] [<ffffffc0000cf188>] __handle_domain_irq+0x90/0xb8
  [   87.757999] [<ffffffc000081ca4>] gic_handle_irq+0x6c/0xc8
  [   87.763899] Exception stack(0xffffffc00081bdc0 to 0xffffffc00081bef0)

Problem is that the state of ath11k_skb_cb->flags must be considered
unknown and could contain anything when it is not manually initialized. So
it could also contain ATH11K_SKB_HW_80211_ENCAP. And this can result in the
code to assume that the ath11k_skb_cb->vif is set - even when this is not
always the case for non ATH11K_SKB_HW_80211_ENCAP transmissions.

Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2

[1] https://source.codeaurora.org/quic/qsdk/oss/system/feeds/wlan-open/tree/mac80211/patches?h=NHSS.QSDK.11.4.r3
    (162 patches at the moment which are often not upstreamed but essential
     to get ath11k working)

Fixes: e7f33e0c52c0 ("ath11k: add tx hw 802.11 encapsulation offloading support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-2-sven@narfation.org

ath11k: Don't cast ath11k_skb_cb to ieee80211_tx_info.control

The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.

But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a

ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0

or (slightly worse) in a kernel oops.

Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.

Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org

ath11k: remove "ath11k_mac_get_ar_vdev_stop_status" references

Unused structure ath11k_vdev_stop_status is removed.
'ath11k_mac_get_ar_vdev_stop_status' api has been replaced
with 'ath11k_mac_get_ar_by_vdev_id' inside vdev_stopped_event.

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-4-git-send-email-mkenna@codeaurora.org

ath11k: peer delete synchronization with firmware

Peer creation in firmware fails, if last peer deletion
is still in progress.
Hence, add wait for the event after deleting every peer
from host driver to synchronize with firmware.

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-3-git-send-email-mkenna@codeaurora.org

ath11k: vdev delete synchronization with firmware

When the interface is added immediately after removing the
interface, vdev deletion in firmware might not have been
completed.

Hence, add vdev_delete_resp_event and wait_event_timeout
to synchronize with firmware.

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-2-git-send-email-mkenna@codeaurora.org

Merge mhi-ath11k-immutable into ath-next

This is an immutable branch from mhi tree for handling an API change in MHI
subsystem and minimise conflicts between ath and mhi trees.

ath11k: Fix the rx_filter flag setting for peer rssi stats

Set the rx_filter in ath11k_mac_config_mon_status_default(),
only when the rx_filter value exists in ath11k_debug_rx_filter().

Without this change, rx_filter gets set to 0 and peer rssi stats
aren't updating properly from firmware.

Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01230-QCAHKSWPL_SILICONZ-4

Fixes: ec48d28ba291 ("ath11k: Fix rx_filter flags setting for per peer rx_stats")

Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605091117-11005-1-git-send-email-mkenna@codeaurora.org

ath10k: add target IRAM recovery feature support

This target IRAM recovery feature support is to copy target
IRAM contents available at ATH10K_MEM_REGION_TYPE_REG to host
memory for back up after firmware loaded. Target IRAM contents
are copied to wmi memory chunks allocated for the
WMI_IRAM_RECOVERY_HOST_MEM_REQ_ID and provide the wmi chunks
address to the firmware through wmi init command.

If firmware detects andy IRAM corruption through periodic
checksum validation, It will download the IRAM contents back
from the provided wmi memory chunks address using hif_memcpy.

This IRAM recovery feature prevent target assert in case of
unexpected target IRAM corruptions.

This patch also introduce a new feature flag 'iram-recovery' for
backward compatibility.

Tested-on: QCA9888 10.4-3.9.0.2-00094

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604657442-23674-1-git-send-email-vnaralas@codeaurora.org

ath11k: Fix beamformee STS in HE cap

STS Beamformee capability sent from firmware is overwritten as
num_tx_chains - 1.
When num_tx_chains is 2, then STS is set to invalid value 1.
Since STS is not limited by number of TX chain, not overwriting the
capability received from firmware.

Tested on: IPQ6018 WLAN.HK.2.4.0.1-00303-QCAHKSWPL_SILICONZ-1

Signed-off-by: Ramya Gnanasekar <rgnanase@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604933229-15815-1-git-send-email-rgnanase@codeaurora.org

ath11k: add processor_id based ring_selector logic

Current ring selector logic follows round-robin scheduling,
when a process switch from one processor to another each time,
the data in the cache would have to be invalidated
and re-loaded from RAM leads to poor cache utilization.

Therefore smp_processor_id() attempt to keep processes
on the same processor via processor affinity which improves
cache utilization. Also, ring selection could be chosen round
robin when the processor_id based ring selection does not
have the resources.

Tested-on : IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00874-QCAHKSWPL_SILICONZ-1

Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604914915-12831-1-git-send-email-ppranees@codeaurora.org

net: qrtr: Unprepare MHI channels during remove

Reset MHI device channels when driver remove is called due to
module unload or any crash scenario. This will make sure that
MHI channels no longer remain enabled for transfers since the
MHI stack does not take care of this anymore after the auto-start
channels feature was removed.

Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

net: qrtr: Start MHI channels during init

Start MHI device channels so that transfers can be performed.
The MHI stack does not auto-start channels anymore.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

bus: mhi: Remove auto-start option

There is really no point having an auto-start for channels.
This is confusing for the device drivers, some have to enable the
channels, others don't have... and waste resources (e.g. pre allocated
buffers) that may never be used.

This is really up to the MHI device(channel) driver to manage the state
of its channels.

While at it, let's also remove the auto-start option from ath11k mhi
controller.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mani: clubbed ath11k change]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

ath11k: Handle errors if peer creation fails

ath11k_peer_create() is called without its return value being checked,
meaning errors will be unhandled. Add missing check and, as the mutex is
unconditionally unlocked on leaving this function, simplify the exit
path.

Addresses-Coverity-ID: 1497531 ("Code maintainability issues")
Fixes: 701e48a43e15 ("ath11k: add packet log support for QCA6390")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004100218.311653-1-alex.dewar90@gmail.com

ath9k: work around false-positive gcc warning

gcc-10 shows a false-positive warning with CONFIG_KASAN:

drivers/net/wireless/ath/ath9k/dynack.c: In function 'ath_dynack_sample_tx_ts':
include/linux/etherdevice.h:290:14: warning: writing 4 bytes into a region of size 0 [-Wstringop-overflow=]
290 | *(u32 *)dst = *(const u32 *)src;
| ~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~

Until gcc is fixed, work around this by using memcpy() in place
of ether_addr_copy(). Hopefully gcc-11 will not have this problem.

Link: https://godbolt.org/z/sab1MK
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=97490
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[kvalo@codeaurora.org: remove ifdef and add a comment]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-8-arnd@kernel.org

ath11k: fix ZERO address in probe request

Host needs to pass at least on bssid with all 0xff to firmware in
WMI_START_SCAN_CMDID, otherwise the bssid and receiver address
in probe requeste are all ZEROs.

This also fixed some hidden AP connection issue because some AP
doesn't respond to probe request which receiver address are all
ZEROs.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201012101733.24137-1-cjhuang@codeaurora.org

wil6210: wmi: Correct misnamed function parameter 'ptr_'

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Function parameter or member 'ptr_' not described in 'wmi_buffer_block'
drivers/net/wireless/ath/wil6210/wmi.c:279: warning: Excess function parameter 'ptr' description in 'wmi_buffer_block'

Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: wil6210@qti.qualcomm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-2-lee.jones@linaro.org

wcn36xx: Enable firmware offloaded keepalive

This patch calls wcn36xx_smd_keep_alive_req() on the STA patch immediately
after associating with an AP.

This will cause the firmware to send a NULL packet out to the AP every 30
seconds, thus offloading keep-alive processing from the SoC to the
firmware.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-4-bryan.odonoghue@linaro.org

wcn36xx: Enable firmware link monitoring

This patch switches on CONNECTION_MONITOR. Once done it is up to the
firmware to send keep alive and to monitor the link state.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-3-bryan.odonoghue@linaro.org

wcn36xx: Set LINK_FAIL_TX_CNT to 1000 on all wcn36xx

The firmware parameter LINK_FAIL_TX_CNT maps to the prima configuration
file parameter gLinkFailTxCnt and is described as:

quote: " If within gLinkFailTimeout period(values is mentioned in msec) if
         FW doesn't receive acks for gLinkFailTxCnt number of packets, then
         link will be disconnected."

The downstream description sets a minimum value of 1000 a maximum value of
60000 and a default value of 6000, however it appears that unless we
actually set this value deliberately firmware defaults it to 0.

Setting this value to non-zero results in the firmware doing link
monitoring. The working example from downstream paradoxically sets the
value to 200, here we opt to set the value to the minimum stipulated in the
configuration file 1000.

In conjunction with ieee80211_hw_set(wcn->hw, CONNECTION_MONITOR); this
change effects offload of link monitoring to the firmware.

Tested with:
'CNSS-PR-2-0-1-2-c1-74-130449-3' wcn3620
'CNSS-PR-2-0-1-2-c1-00083'       wcn3680

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103121735.291324-2-bryan.odonoghue@linaro.org

ath6kl: fix enum-conversion warning

gcc -Wextra points out a type mismatch

drivers/net/wireless/ath/ath6kl/wmi.c: In function 'ath6kl_wmi_cmd_send':
drivers/net/wireless/ath/ath6kl/wmi.c:1825:19: warning: implicit conversion from 'enum <anonymous>' to 'enum wmi_data_hdr_data_type' [-Wenum-conversion]
1825 | false, false, 0, NULL, if_idx);
| ^~~~~

As far as I can tell, the numeric value is current here,
so just use the correct enum literal instead of 'false'.

Fixes: bdcd81707973 ("Add ath6kl cleaned up driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-9-arnd@kernel.org

ath9k: dynack: Demote non-compliant function header

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'old' not described in 'ath_dynack_ewma'
drivers/net/wireless/ath/ath9k/dynack.c:52: warning: Function parameter or member 'new' not described in 'ath_dynack_ewma'

Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-40-lee.jones@linaro.org

ath9k: ar5008_phy: Demote half completed function headers

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'rfBuf' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'reg32' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'numBits' not described in 'ar5008_hw_phy_modify_rx_buffer'
drivers/net/wireless/ath/ath9k/ar5008_phy.c:119: warning: Function parameter or member 'firstBit' not described in 'ar5008_hw_phy_modify_rx_buffer'

Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-21-lee.jones@linaro.org

ath9k: ar9003_2p2_initvals: Remove unused const variables

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1734:18: warning: ‘ar9300PciePhy_clkreq_disable_L1_2p2’ defined but not used [-Wunused-const-variable=]
drivers/net/wireless/ath/ath9k/ar9003_2p2_initvals.h:1727:18: warning: ‘ar9300PciePhy_clkreq_enable_L1_2p2’ defined but not used [-Wunused-const-variable=]

Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-14-lee.jones@linaro.org

ath9k: ar9485_initvals: Remove unused const variable 'ar9485_fast_clock_1_1_baseband_postamble'

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/ath9k/ar9485_initvals.h:1009:18: warning: ‘ar9485_fast_clock_1_1_baseband_postamble’ defined but not used [-Wunused-const-variable=]

Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-13-lee.jones@linaro.org

ath9k: ar9340_initvals: Remove unused const variable 'ar9340Modes_ub124_tx_gain_table_1p0'

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/ath9k/ar9340_initvals.h:624:18: warning: ‘ar9340Modes_ub124_tx_gain_table_1p0’ defined but not used [-Wunused-const-variable=]

Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-12-lee.jones@linaro.org

ath9k: ar9330_1p1_initvals: Remove unused const variable 'ar9331_common_tx_gain_offset1_1'

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/ath9k/ar9330_1p1_initvals.h:1013:18: warning: ‘ar9331_common_tx_gain_offset1_1’ defined but not used [-Wunused-const-variable=]

Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-11-lee.jones@linaro.org

ath: dfs_pri_detector: Demote zero/half completed kernel-doc headers

There are only a couple of these and none of them are conformant.

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/dfs_pri_detector.c:39: warning: Function parameter or member 'head' not described in 'pulse_elem'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'val' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'fraction' not described in 'pde_get_multiple'
drivers/net/wireless/ath/dfs_pri_detector.c:46: warning: Function parameter or member 'tolerance' not described in 'pde_get_multiple'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-23-lee.jones@linaro.org

ath: dfs_pattern_detector: Fix some function kernel-doc headers

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/dfs_pattern_detector.c:34: warning: Function parameter or member 'region' not described in 'radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:141: warning: Function parameter or member 'region' not described in 'get_dfs_domain_radar_types'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'dpd' not described in 'channel_detector_get'
drivers/net/wireless/ath/dfs_pattern_detector.c:239: warning: Function parameter or member 'freq' not described in 'channel_detector_get'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-22-lee.jones@linaro.org

ath: regd: Provide description for ath_reg_apply_ir_flags's 'reg' param

Fixes the following W=1 kernel build warning(s):

drivers/net/wireless/ath/regd.c:378: warning: Function parameter or member 'reg' not described in 'ath_reg_apply_ir_flags'

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201102112410.1049272-20-lee.jones@linaro.org

ath11k: Add new dfs region name for JP

Japan has new Radar types as per latest regulatory,
included under MKK_N in FW. So adding new enum in
ath11k to support it.

Tested-on: IPQ8074 hw2.0 PCI WLAN.HK.2.4.0.1-00041-QCAHKSWPL_SILICONZ-1

Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604563475-5782-1-git-send-email-lavaks@codeaurora.org

ath11k: fix wmi init configuration

Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.

Found this during code review.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Fixes: 2d4bcbed5b7d53e1 ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org

ath11k: Fix the hal descriptor mask

Below listed hal descriptor mask are incorrect, so modify it to correct one
- CE destination status description meta info mask is increased from
8 bits to 16 bits from the 0th bit position
- Rx Reo queue duplicate count mask is decreased from 22 bits to 16 bits
- Reo threshold status counter sum mask is increased from 24 bits to 26 bits

No functionality impact, these descriptors are currently not used in any
supported platform. But in future if someone referred these descriptor then
ended with wrong values.

Found this during code review.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511921-24840-1-git-send-email-periyasa@codeaurora.org

ath11k: Fix single phy hw mode

driver not able to bootup in the single radio configured board.
single phy hw mode is converted to invalid hw mode and sent to FW
through wmi init cmd. In that case driver is not receiving wmi
ready event which leads to driver bootup fail. single phy hw mode
is a valid for single radio configured board. so removed the
conversion logic.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2

Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604511331-22477-1-git-send-email-periyasa@codeaurora.org

ath11k: Fix number of rules in filtered ETSI regdomain

The ath11k code will try to insert wheather rader related limits when the
DFS region is set to ETSI. For this reason, it will add two more entries in
the array of reg_rules. But the 2.4.0.1 firmware is prefiltering the list
of reg rules it returns for 2.4GHz PHYs. They will then not contain the
list of 5GHz rules and thus no wheather radar band rules were inserted by
this code.

But the code didn't fix the n_reg_rules for this regulatory domain and PHY
when this happened. This resulted in a rejection by is_valid_rd because it
found rules which start and end at 0khz. This resulted in a splat like:

  Invalid regulatory domain detected
  ------------[ cut here ]------------
  WARNING: at backports-20200628-4.4.60-9a94b73e75/net/wireless/reg.c:3721
  [...]
  ath11k c000000.wifi1: failed to perform regd update : -22

The number of rules must therefore be saved after they were converted from
the ath11k format to the ieee80211_regdomain format and not before.

Tested with IPQ8074 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030101940.2387952-1-sven@narfation.org

ath11k: Remove unused param from wmi_mgmt_params

qdf_ctx is not used in wmi_mgmt_params, remove this
un-used variable.

Compile tested only.

Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603339175-12706-1-git-send-email-govinds@codeaurora.org

ath11k: Initialize complete alpha2 for regulatory change

The function ath11k_wmi_send_init_country_cmd is taking 3 byte from alpha2
of the structure wmi_init_country_params. But the function
ath11k_reg_notifier is only initializing 2 bytes. The third byte is
therefore always an uninitialized value.

The command can happen to look like

0c 00 87 02 01 00 00 00 00 00 00 00 43 41 f8 00

instead of

0c 00 87 02 01 00 00 00 00 00 00 00 43 41 00 00

Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01161-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00019-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201021140555.4114715-1-sven@narfation.org

ath11k: cold boot calibration support

cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.

caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.

This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.

Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1

Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org

ath11k: search DT for qcom,ath11k-calibration-variant

Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.

The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.

This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.

The device tree requires an additional string to define the variant name

    wifi@c000000 {
        status = "okay";
        qcom,ath11k-calibration-variant = "Cigtech-WF-188";
    };

This would create the boarddata identifier for the board-2.bin search

*  bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org

dt: bindings: add new dt entry for ath11k calibration variant

The bus + qmi-chip-id + qmi-board-id is not enough to identify the correct
board data file on IPQ6018 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.

An additional "variant" information has to be provided to select the
correct board data for a design which was modified by an ODM. This follows
the same approach as ath10k.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-1-sven@narfation.org

ath11k: Remove unnecessary data sync to cpu on monitor buffer

Monitor ring Rx buffer is not really modified between dma map
and unmap. So remove the unnecssary data sync before dma unmap.
This does not fix any visible issue, found in code review.

Compile tested only.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602744454-22969-1-git-send-email-vthiagar@codeaurora.org

ath11k: convert tasklets to use new tasklet_setup() API

In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.

Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007103309.363737-4-allen.lkml@gmail.com

ath10k: cancel rx worker in hif_stop for SDIO

The rx worker of SDIO should be cancelled after disable interrupt, and
release rx sk_buff in queue, otherwise the rx worker maybe still run
after hif_stop. And it should be cancelled before napi_synchronize in
hif_stop, because the rx worker of SDIO will call napi_schedule, it
should have no napi_schedule before napi_synchronize, otherwise it
lead napi_synchronize wait untill napi_complete.

Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604558036-4056-1-git-send-email-wgong@codeaurora.org

ath10k: Don't iterate over not-sdata-in-driver interfaces.

This fixes possible crash scenario where interfaces that were not
set up in the driver yet might still be iterated over.  When originally
debugged on the ath10k-ct driver, the crash looked like this:

kernel BUG at /home/greearb/git/linux-4.7.dev.y/drivers/net/wireless/ath/ath10k/wmi.c:1781!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
Modules linked in: nf_conntrack_netlink nf_conntrack nfnetlink nf_defrag_ipv4 bridge carl9170 mac80211_hwsim ath10k_pci ath10k_core ath5k ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 8021q garp mrp stp llc bnep bluetooth fuse macvlan pktgen rpcsec_gss_krb5 nfsv4 nfs fscache snd_hda_codec_hdmi coretemp hwmon intel_rapl x86_pkg_temp_thermal intel_powerclamp snd_hda_codec_realtek snd_hda_codec_generic kvm iTCO_wdt irqbypass iTCO_vendor_support joydev snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device pcspkr snd_pcm snd_timer shpchp snd i2c_i801 lpc_ich soundcore tpm_tis tpm nfsd auth_rpcgss nfs_acl lockd grace sunrpc i915 serio_raw i2c_algo_bit drm_kms_helper ata_generic e1000e pata_acpi drm ptp pps_core i2c_core fjes video ipv6 [last unloaded: nf_conntrack]
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.7.10+ #15
Hardware name: To be filled by O.E.M. To be filled by O.E.M./ChiefRiver, BIOS 4.6.5 06/07/2013
task: ffff8801d4f20000 ti: ffff8801d4f28000 task.ti: ffff8801d4f28000
RIP: 0010:[<ffffffffa0efbcfb>]  [<ffffffffa0efbcfb>] ath10k_wmi_tx_beacons_iter+0x28b/0x290 [ath10k_core]
RSP: 0018:ffff8801d6447a98  EFLAGS: 00010293
RAX: 0000000000000018 RBX: ffff8801ce97e1d8 RCX: 0000000000000000
RDX: 0000000000000018 RSI: 0000000000000003 RDI: ffffed003ac88f49
RBP: ffff8801d6447af0 R08: 0000000000000003 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000
R13: ffff8801ce97e320 R14: ffff8801ce97e378 R15: ffff8801ce97ca40
FS:  0000000000000000(0000) GS:ffff8801d6440000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007eff191ef1ab CR3: 000000000260a000 CR4: 00000000001406e0
Stack:
1ffff1003ac88f59 0000000041b58ab3 ffffffffa0f4d52a ffff8801d4f20000
0000000000000246 0000000000000002 ffff8801ce97e1d8 ffff8801bd5d39b8
0000000000000002 0000000000000001 ffff8801ce97ca40 ffff8801d6447b48
Call Trace:
<IRQ>
[<ffffffffa0d03e5c>] __iterate_interfaces+0xfc/0x1d0 [mac80211]
[<ffffffffa0efba70>] ? ath10k_wmi_cmd_send_nowait+0x260/0x260 [ath10k_core]
[<ffffffffa0efba70>] ? ath10k_wmi_cmd_send_nowait+0x260/0x260 [ath10k_core]
[<ffffffffa0d04477>] ieee80211_iterate_active_interfaces_atomic+0x67/0x100 [mac80211]
[<ffffffffa0d04410>] ? ieee80211_handle_reconfig_failure+0x140/0x140 [mac80211]
[<ffffffffa0ef4060>] ? ath10k_tpc_config_disp_tables+0x620/0x620 [ath10k_core]
[<ffffffffa0ef408b>] ath10k_wmi_op_ep_tx_credits+0x2b/0x50 [ath10k_core]
[<ffffffffa0ee2fd2>] ath10k_htc_rx_completion_handler+0x422/0x5c0 [ath10k_core]
[<ffffffffa0b4301e>] ath10k_pci_process_rx_cb+0x37e/0x430 [ath10k_pci]
[<ffffffffa0ee2bb0>] ? ath10k_htc_build_tx_ctrl_skb+0xc0/0xc0 [ath10k_core]
[<ffffffffa0b42ca0>] ? ath10k_pci_rx_post_pipe+0x550/0x550 [ath10k_pci]
[<ffffffff8120cbe5>] ? debug_lockdep_rcu_enabled+0x35/0x40
[<ffffffff811e1893>] ? mark_held_locks+0x23/0xc0
[<ffffffff8116019a>] ? __local_bh_enable_ip+0x6a/0xd0
[<ffffffff811e1abb>] ? trace_hardirqs_on_caller+0x18b/0x290
[<ffffffff811e1bcd>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff8116019a>] ? __local_bh_enable_ip+0x6a/0xd0
[<ffffffff81df11d0>] ? _raw_spin_unlock_bh+0x30/0x40
[<ffffffffa0b4902e>] ? ath10k_ce_per_engine_service+0xee/0x100 [ath10k_pci]
[<ffffffffa0b43139>] ath10k_pci_htt_htc_rx_cb+0x29/0x30 [ath10k_pci]
[<ffffffffa0b48fe6>] ath10k_ce_per_engine_service+0xa6/0x100 [ath10k_pci]
[<ffffffffa0b49116>] ath10k_ce_per_engine_service_any+0xd6/0xf0 [ath10k_pci]
[<ffffffffa0b45800>] ? ath10k_pci_enable_legacy_irq+0xe0/0xe0 [ath10k_pci]
[<ffffffffa0b4585f>] ath10k_pci_tasklet+0x5f/0xb0 [ath10k_pci]
[<ffffffff81160445>] tasklet_action+0x245/0x2b0
[<ffffffff81df4831>] __do_softirq+0x181/0x595
[<ffffffff8116137c>] irq_exit+0xbc/0xc0
[<ffffffff81df423c>] do_IRQ+0x7c/0x150
[<ffffffff81df23cc>] common_interrupt+0x8c/0x8c
<EOI>
[<ffffffff811e1abb>] ? trace_hardirqs_on_caller+0x18b/0x290
[<ffffffff81b722ae>] ? cpuidle_enter_state+0x1ae/0x4b0
[<ffffffff81b722a7>] ? cpuidle_enter_state+0x1a7/0x4b0
[<ffffffff81b72602>] cpuidle_enter+0x12/0x20
[<ffffffff811d0b6e>] call_cpuidle+0x4e/0x90
[<ffffffff811d10e7>] cpu_startup_entry+0x3f7/0x540
[<ffffffff811d0cf0>] ? default_idle_call+0x50/0x50
[<ffffffff81234bdf>] ? clockevents_config_and_register+0x5f/0x70
[<ffffffff81085a9a>] ? setup_APIC_timer+0xfa/0x110
[<ffffffff81083b63>] start_secondary+0x253/0x2b0
[<ffffffff81083910>] ? set_cpu_sibling_map+0x920/0x920
Code: 4d 49 e0 8b b3 48 01 00 00 48 c7 c7 a0 ee f3 a0 e8 d9 c2 3f e0 49 81 fd 3f 1f 00 00 76 0f 49 81 fc 3f 1f 00 00 0f 87 c0 fd ff ff <0f> 0b 0f 0b 90 55 48 89 e5 41 57 41 56 48 8d 85 58 ff ff ff 41
RIP  [<ffffffffa0efbcfb>] ath10k_wmi_tx_beacons_iter+0x28b/0x290 [ath10k_core]
RSP <ffff8801d6447a98>
---[ end trace 6588464714e5163a ]---

Similar logic was tested for years in ath10k-ct driver and various firmware.

Also tested with stock kernel plus this patch, with firmware
10.2.4-1.0-00037

This test case was to bring up 5 vap on a radio and fake a firmware
crash.  Make sure ap interfaces continue to function properly.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200922191957.25257-2-greearb@candelatech.com

ath10k: fix compilation warning

This change fixes below compilation warning.

smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:9125 ath10k_mac_op_set_tid_config() error: uninitialized symbol 'ret'.

No functional changes. Compile tested only.

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604507837-29361-1-git-send-email-tamizhr@codeaurora.org

ath11k: FILS discovery and unsolicited broadcast probe response support

This patch adds driver support for FILS discovery and unsolicited
broadcast probe response transmission features which are used for
in-band discovery in 6GHz band.
Currently this support is enabled only in 6GHz by setting hardware flags.

Changes include WMI commands to enable transmission, set packet
interval, set template, and handle events.

Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201007204036.19780-1-alokad@codeaurora.org

ath10k: sdio: remove redundant check in for loop

The for loop checks whether cur_section is NULL on every iteration, but
we know it can never be NULL as there is another check towards the
bottom of the loop body. Refactor to avoid this unnecessary check.

Also, increment the variable i inline for clarity

Addresses-Coverity: 1496984 ("Null pointer dereferences)
Suggested-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200916165748.20927-1-alex.dewar90@gmail.com

ath11k: remove repeated words in comments and warnings

Found by latest checkpatch.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603803705-22447-1-git-send-email-kvalo@codeaurora.org

ath10k: ath10k_pci_init_irq(): workaround for checkpatch fallthrough warning

Latest checkpatch complains about use of fall-through comment. But as this is a
switch statement just reword the comment to workaround the problem.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603802288-21158-2-git-send-email-kvalo@codeaurora.org

ath10k: remove repeated words in comments

Found by latest checkpatch.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603802288-21158-1-git-send-email-kvalo@codeaurora.org

Linux 5.10-rc1

treewide: Convert macro and uses of __section(foo) to __section("foo")

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl

Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/sys.c: fix prototype of prctl_get_tid_address()

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: remove kzfree() compatibility definition

Commit 453431a54934 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

checkpatch: enable GIT_DIR environment use to set git repository location

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'timers-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull timer fixes from Thomas Gleixner:
"A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Merge tag 'sched-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Thomas Gleixner:
"Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Merge tag 'perf-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull perf fix from Thomas Gleixner:
"A single fix to compute the field offset of the SNOOPX bit in the data
source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: correct SNOOPX field offset

Merge tag 'locking-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip

Pull locking fix from Thomas Gleixner:
"Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlocks: Fix kernel-doc warnings

Merge tag 'ntb-5.10' of git://github.com/jonmason/ntb

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Merge branch 'i2c/for-5.10' of git://git./linux/kernel/git/wsa/linux

Pull i2c fix from Wolfram Sang:
"Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Merge tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6

Pull more cifs updates from Steve French:
"Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Merge branch 'parisc-5.10-2' of git://git./linux/kernel/git/deller/parisc-linux

Pull more parisc updates from Helge Deller:

- During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

- Improve error return codes when setting rtc time

- Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Merge tag 'for-linus-5.10b-rc1c-tag' of git://git./linux/kernel/git/xen/tip

Pull more xen updates from Juergen Gross:

- a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

- a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants

Merge tag 'safesetid-5.10' of git://github.com/micah-morton/linux

Pull SafeSetID updates from Micah Morton:
"The changes are mostly contained to within the SafeSetID LSM, with the
  exception of a few 1-line changes to change some ns_capable() calls to
  ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
  is examined by SafeSetID code and nothing else in the kernel.

  The changes to SafeSetID internally allow for setting up GID
  transition security policies, as already existed for UIDs"

* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
  LSM: SafeSetID: Fix warnings reported by test bot
  LSM: SafeSetID: Add GID security policy handling
  LSM: Signal to SafeSetID when setting group IDs

Merge tag '20201024-v4-5.10' of git://git./linux/kernel/git/wtarreau/prandom

Pull random32 updates from Willy Tarreau:
"Make prandom_u32() less predictable.

  This is the cleanup of the latest series of prandom_u32
  experimentations consisting in using SipHash instead of Tausworthe to
  produce the randoms used by the network stack.

  The changes to the files were kept minimal, and the controversial
  commit that used to take noise from the fast_pool (f227e3ec3b5c) was
  reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
  fed from various sources of activities (networking, scheduling) to
  perturb the SipHash state using fast, non-trivially predictable data,
  instead of keeping it fully deterministic. The goal is essentially to
  make any occasional memory leakage or brute-force attempt useless.

  The resulting code was verified to be very slightly faster on x86_64
  than what is was with the controversial commit above, though this
  remains barely above measurement noise. It was also tested on i386 and
  arm, and build- tested only on arm64"

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
* tag '20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
  random32: add a selftest for the prandom32 code
  random32: add noise from network and scheduling activity
  random32: make prandom_u32() output unpredictable

i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Commit 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().

But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().

Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.

This fixes the Microsoft Surface Go 2 hanging at boot.

Fixes: 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Merge tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:

- NVMe pull request from Christoph
     - rdma error handling fixes (Chao Leng)
     - fc error handling and reconnect fixes (James Smart)
     - fix the qid displace when tracing ioctl command (Keith Busch)
     - don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
     - fix MTDT for passthru (Logan Gunthorpe)
     - blacklist Write Same on more devices (Kai-Heng Feng)
     - fix an uninitialized work struct (zhenwei pi)"

- lightnvm out-of-bounds fix (Colin)

- SG allocation leak fix (Doug)

- rnbd fixes (Gioh, Guoqing, Jack)

- zone error translation fixes (Keith)

- kerneldoc markup fix (Mauro)

- zram lockdep fix (Peter)

- Kill unused io_context members (Yufen)

- NUMA memory allocation cleanup (Xianting)

- NBD config wakeup fix (Xiubo)

* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
  block: blk-mq: fix a kernel-doc markup
  nvme-fc: shorten reconnect delay if possible for FC
  nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
  nvme-fc: fix error loop in create_hw_io_queues
  nvme-fc: fix io timeout to abort I/O
  null_blk: use zone status for max active/open
  nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
  nvmet: cleanup nvmet_passthru_map_sg()
  nvmet: limit passthru MTDS by BIO_MAX_PAGES
  nvmet: fix uninitialized work for zero kato
  nvme-pci: disable Write Zeroes on Sandisk Skyhawk
  nvme: use queuedata for nvme_req_qid
  nvme-rdma: fix crash due to incorrect cqe
  nvme-rdma: fix crash when connect rejected
  block: remove unused members for io_context
  blk-mq: remove the calling of local_memory_node()
  zram: Fix __zram_bvec_{read,write}() locking order
  skd_main: remove unused including <linux/version.h>
  sgl_alloc_order: fix memory leak
  lightnvm: fix out-of-bounds write to array devices->info[]
  ...

Merge tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block

Pull io_uring fixes from Jens Axboe:

- fsize was missed in previous unification of work flags

- Few fixes cleaning up the flags unification creds cases (Pavel)

- Fix NUMA affinities for completely unplugged/replugged node for io-wq

- Two fallout fixes from the set_fs changes. One local to io_uring, one
   for the splice entry point that io_uring uses.

- Linked timeout fixes (Pavel)

- Removal of ->flush() ->files work-around that we don't need anymore
   with referenced files (Pavel)

- Various cleanups (Pavel)

* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  splice: change exported internal do_splice() helper to take kernel offset
  io_uring: make loop_rw_iter() use original user supplied pointers
  io_uring: remove req cancel in ->flush()
  io-wq: re-set NUMA node affinities if CPUs come online
  io_uring: don't reuse linked_timeout
  io_uring: unify fsize with def->work_flags
  io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
  io_uring: do poll's hash_node init in common code
  io_uring: inline io_poll_task_handler()
  io_uring: remove extra ->file check in poll prep
  io_uring: make cached_cq_overflow non atomic_t
  io_uring: inline io_fail_links()
  io_uring: kill ref get/drop in personality init
  io_uring: flags-based creds init in queue

Merge tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block

Pull libata fixes from Jens Axboe:
"Two minor libata fixes:

   - Fix a DMA boundary mask regression for sata_rcar (Geert)

   - kerneldoc markup fix (Mauro)"

* tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
  ata: fix some kernel-doc markups
  ata: sata_rcar: Fix DMA boundary mask

Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs

Pull misc vfs updates from Al Viro:
"Assorted stuff all over the place (the largest group here is
  Christoph's stat cleanups)"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: remove KSTAT_QUERY_FLAGS
  fs: remove vfs_stat_set_lookup_flags
  fs: move vfs_fstatat out of line
  fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
  fs: remove vfs_statx_fd
  fs: omfs: use kmemdup() rather than kmalloc+memcpy
  [PATCH] reduce boilerplate in fsid handling
  fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
  selftests: mount: add nosymfollow tests
  Add a "nosymfollow" mount option.

Merge tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping

Pull dma-mapping fixes from Christoph Hellwig:

- document the new dma_{alloc,free}_pages() API

- two fixups for the dma-mapping.h split

* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: document dma_{alloc,free}_pages
  dma-mapping: move more functions to dma-map-ops.h
  ARM/sa1111: add a missing include of dma-map-ops.h

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull KVM fixes from Paolo Bonzini:
"Two fixes for this merge window, and an unrelated bugfix for a host
  hang"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: ioapic: break infinite recursion on lazy EOI
  KVM: vmx: rename pi_init to avoid conflict with paride
  KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build

Merge tag 'x86_seves_fixes_for_v5.10_rc1' of git://git./linux/kernel/git/tip/tip

Pull x86 SEV-ES fixes from Borislav Petkov:
"Three fixes to SEV-ES to correct setting up the new early pagetable on
  5-level paging machines, to always map boot_params and the kernel
  cmdline, and disable stack protector for ../compressed/head{32,64}.c.
  (Arvind Sankar)"

* tag 'x86_seves_fixes_for_v5.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Explicitly map boot_params and command line
  x86/head/64: Disable stack protection for head$(BITS).o
  x86/boot/64: Initialize 5-level paging variables earlier

random32: add a selftest for the prandom32 code

Given that this code is new, let's add a selftest for it as well.
It doesn't rely on fixed sets, instead it picks 1024 numbers and
verifies that they're not more correlated than desired.

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>

random32: add noise from network and scheduling activity

With the removal of the interrupt perturbations in previous random32
change (random32: make prandom_u32() output unpredictable), the PRNG
has become 100% deterministic again. While SipHash is expected to be
way more robust against brute force than the previous Tausworthe LFSR,
there's still the risk that whoever has even one temporary access to
the PRNG's internal state is able to predict all subsequent draws till
the next reseed (roughly every minute). This may happen through a side
channel attack or any data leak.

This patch restores the spirit of commit f227e3ec3b5c ("random32: update
the net random state on interrupt and activity") in that it will perturb
the internal PRNG's statee using externally collected noise, except that
it will not pick that noise from the random pool's bits nor upon
interrupt, but will rather combine a few elements along the Tx path
that are collectively hard to predict, such as dev, skb and txq
pointers, packet length and jiffies values. These ones are combined
using a single round of SipHash into a single long variable that is
mixed with the net_rand_state upon each invocation.

The operation was inlined because it produces very small and efficient
code, typically 3 xor, 2 add and 2 rol. The performance was measured
to be the same (even very slightly better) than before the switch to
SipHash; on a 6-core 12-thread Core i7-8700k equipped with a 40G NIC
(i40e), the connection rate dropped from 556k/s to 555k/s while the
SYN cookie rate grew from 5.38 Mpps to 5.45 Mpps.

Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>

random32: make prandom_u32() output unpredictable

Non-cryptographic PRNGs may have great statistical properties, but
are usually trivially predictable to someone who knows the algorithm,
given a small sample of their output.  An LFSR like prandom_u32() is
particularly simple, even if the sample is widely scattered bits.

It turns out the network stack uses prandom_u32() for some things like
random port numbers which it would prefer are *not* trivially predictable.
Predictability led to a practical DNS spoofing attack.  Oops.

This patch replaces the LFSR with a homebrew cryptographic PRNG based
on the SipHash round function, which is in turn seeded with 128 bits
of strong random key.  (The authors of SipHash have *not* been consulted
about this abuse of their algorithm.)  Speed is prioritized over security;
attacks are rare, while performance is always wanted.

Replacing all callers of prandom_u32() is the quick fix.
Whether to reinstate a weaker PRNG for uses which can tolerate it
is an open question.

Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") was an earlier attempt at a solution.  This patch replaces
it.

Reported-by: Amit Klein <aksecurity@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Fixes: f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Signed-off-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
[ willy: partial reversal of f227e3ec3b5c; moved SIPROUND definitions
  to prandom.h for later use; merged George's prandom_seed() proposal;
  inlined siprand_u32(); replaced the net_rand_state[] array with 4
  members to fix a build issue; cosmetic cleanups to make checkpatch
  happy; fixed RANDOM32_SELFTEST build ]
Signed-off-by: Willy Tarreau <w@1wt.eu>

Merge tag 'powerpc-5.10-2' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:

- A fix for undetected data corruption on Power9 Nimbus <= DD2.1 in the
   emulation of VSX loads. The affected CPUs were not widely available.

- Two fixes for machine check handling in guests under PowerVM.

- A fix for our recent changes to SMP setup, when
   CONFIG_CPUMASK_OFFSTACK=y.

- Three fixes for races in the handling of some of our powernv sysfs
   attributes.

- One change to remove TM from the set of Power10 CPU features.

- A couple of other minor fixes.

Thanks to: Aneesh Kumar K.V, Christophe Leroy, Ganesh Goudar, Jordan
Niethe, Mahesh Salgaonkar, Michael Neuling, Oliver O'Halloran, Qian Cai,
Srikar Dronamraju, Vasant Hegde.

* tag 'powerpc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/pseries: Avoid using addr_to_pfn in real mode
  powerpc/uaccess: Don't use "m<>" constraint with GCC 4.9
  powerpc/eeh: Fix eeh_dev_check_failure() for PE#0
  powerpc/64s: Remove TM from Power10 features
  selftests/powerpc: Make alignment handler test P9N DD2.1 vector CI load workaround
  powerpc: Fix undetected data corruption with P9N DD2.1 VSX CI load emulation
  powerpc/powernv/dump: Handle multiple writes to ack attribute
  powerpc/powernv/dump: Fix race while processing OPAL dump
  powerpc/smp: Use GFP_ATOMIC while allocating tmp mask
  powerpc/smp: Remove unnecessary variable
  powerpc/mce: Avoid nmi_enter/exit in real mode on pseries hash
  powerpc/opal_elog: Handle multiple writes to ack attribute

Merge tag 'riscv-for-linus-5.10-mw1' of git://git./linux/kernel/git/riscv/linux

Pull more RISC-V updates from Palmer Dabbelt:
"Just a single patch set: the remainder of Christoph's work to remove
  set_fs, including the RISC-V portion"

* tag 'riscv-for-linus-5.10-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: remove address space overrides using set_fs()
  riscv: implement __get_kernel_nofault and __put_user_nofault
  riscv: refactor __get_user and __put_user
  riscv: use memcpy based uaccess for nommu again
  asm-generic: make the set_fs implementation optional
  asm-generic: add nommu implementations of __{get,put}_kernel_nofault
  asm-generic: improve the nommu {get,put}_user handling
  uaccess: provide a generic TASK_SIZE_MAX definition

Merge tag 'armsoc-defconfig' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
  most of the material here is fairly boring -- some new drivers turned
  on for hardware since they were merged, and some refreshed files due
  to time having moved a lot of entries around"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (33 commits)
  ARM: multi_v7_defconfig: add FMC2 EBI controller support
  arm64: defconfig: enable Qualcomm ASoC modules
  arm64: defconfig: qcom: enable GPU clock controller for SM8[12]50
  arm64: defconfig: enable INTERCONNECT for Qualcomm chipsets
  arm64: defconfig: enable the sl28cpld board management controller
  arm64: defconfig: Enable the eLCDIF and Raydium RM67191 drivers
  arm64: defconfig: Enable Qcom SNPS Femto PHY
  ARM: configs: Update Realview defconfig
  ARM: configs: Update Versatile defconfig
  ARM: config: aspeed_g5: Enable IBM OP Panel driver
  ARM: config: aspeed-g5: Enable I2C GPIO mux driver
  ARM: config: aspeed: Fix selection of media drivers
  arm64: defconfig: Enable Samsung S3FWRN5 NFC driver
  ARM: omap2plus_defconfig: enable generic net options
  ARM: omap2plus_defconfig: enable twl4030_madc as a loadable module
  arm64: defconfig: Enable clock driver for ROHM BD718x7 PMIC
  arm64: defconfig: Build ADMA and ACONNECT driver
  arm64: defconfig: Build AHUB component drivers
  arm64: defconfig: Enable Lontium LT9611 driver
  arm64: defcondfig: Enable USB ACM and FTDI drivers
  ...

Merge tag 'armsoc-dt' of git://git./linux/kernel/git/soc/soc

Pull ARM Devicetree updates from Olof Johansson:
"As usual, most of the changes are to devicetrees.

  Besides smaller fixes, some refactorings and cleanups, some of the new
  platforms and chips (or significant features) supported are below:

  Broadcom boards:
   - Cisco Meraki MR32 (BCM53016-based)
   - BCM2711 (RPi4) display pipeline support

  Actions Semi boards:
   - Caninos Loucos Labrador SBC (S500-based)
   - RoseapplePi SBC (S500-based)

  Allwinner SoCs/boards:
   - A100 SoC with Perf1 board
   - Mali, DMA, Cetrus and IR support for R40 SoC

  Amlogic boards:
   - Libretch S905x CC V2 board
   - Hardkernel ODROID-N2+ board

  Aspeed boards/platforms:
   - Wistron Mowgli (AST2500-based, Power9 OpenPower server)
   - Facebook Wedge400 (AST2500-based, ToR switch)

  Hisilicon SoC:
   - SD5203 SoC

  Nvidia boards:
   - Tegra234 VDK, for pre-silicon Orin SoC

  NXP i.MX boards:
   - Librem 5 phone
   - i.MX8MM DDR4 EVK
   - Variscite VAR-SOM-MX8MN SoM
   - Symphony board
   - Tolino Shine 2 HD
   - TQMa6 SoM
   - Y Soft IOTA Orion

  Rockchip boards:
   - NanoPi R2S board
   - A95X-Z2 board
   - more Rock-Pi4 variants

  STM32 boards:
   - Odyssey SOM board (STM32MP157CAC-based)
   - DH DRC02 board

  Toshiba SoCs/boards:
   - Visconti SoC and TPMV7708 board"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (638 commits)
  ARM: dts: nspire: Fix SP804 users
  arm64: dts: lg: Fix SP804 users
  arm64: dts: lg: Fix SP805 clocks
  ARM: mstar: Fix up the fallout from moving the dts/dtsi files
  ARM: mstar: Add mstar prefix to all of the dtsi/dts files
  ARM: mstar: Add interrupt to pm_uart
  ARM: mstar: Add interrupt controller to base dtsi
  ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
  arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
  arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
  arm64: dts: ti: k3-j7200-main: Add USB controller
  arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
  arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
  dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
  ARM: dts: hisilicon: add SD5203 dts
  ARM: dts: hisilicon: fix the system controller compatible nodes
  arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
  arm64: dts: zynqmp: Remove undocumented u-boot properties
  arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
  arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
  ...

Merge tag 'armsoc-drivers' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
  or cleanups, but some of the new material this time around is:

   - Support for Nvidia Tegra234 SoC

   - Ring accelerator support for TI AM65x

   - PRUSS driver for TI platforms

   - Renesas support for R-Car V3U SoC

   - Reset support for Cortex-M4 processor on i.MX8MQ

  There are also new socinfo entries for a handful of different SoCs and
  platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
  drm/mediatek: reduce clear event
  soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
  soc: mediatek: cmdq: add jump function
  soc: mediatek: cmdq: add write_s_mask value function
  soc: mediatek: cmdq: add write_s value function
  soc: mediatek: cmdq: add read_s function
  soc: mediatek: cmdq: add write_s_mask function
  soc: mediatek: cmdq: add write_s function
  soc: mediatek: cmdq: add address shift in jump
  soc: mediatek: mtk-infracfg: Fix kerneldoc
  soc: amlogic: pm-domains: use always-on flag
  reset: sti: reset-syscfg: fix struct description warnings
  reset: imx7: add the cm4 reset for i.MX8MQ
  dt-bindings: reset: imx8mq: add m4 reset
  reset: Fix and extend kerneldoc
  reset: reset-zynqmp: Added support for Versal platform
  dt-bindings: reset: Updated binding for Versal reset driver
  reset: imx7: Support module build
  soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
  soc: fsl: qman: convert to use be32_add_cpu()
  ...

Merge tag 'armsoc-soc' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
  older platforms that used to have a bunch of board files.

  In particular:

   - Remove non-DT i.MX platforms that haven't seen activity in years,
     it's time to remove them.

   - A bunch of cleanup and removal of platform data for TI/OMAP
     platforms, moving over to genpd for power/reset control (yay!)

   - Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
     closer to multiplatform support (not quite there yet, but getting
     close).

  There are a few other changes too, smaller fixlets, etc. For new
  platform support, the primary ones are:

   - New SoC: Hisilicon SD5203, ARM926EJ-S platform.

   - Cpufreq support for i.MX7ULP"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
  ARM: mstar: Select MStar intc
  ARM: stm32: Replace HTTP links with HTTPS ones
  ARM: debug: add UART early console support for SD5203
  ARM: hisi: add support for SD5203 SoC
  ARM: omap3: enable off mode automatically
  clk: imx: imx35: Remove mx35_clocks_init()
  clk: imx: imx31: Remove mx31_clocks_init()
  clk: imx: imx27: Remove mx27_clocks_init()
  ARM: imx: Remove unused definitions
  ARM: imx35: Retrieve the IIM base address from devicetree
  ARM: imx3: Retrieve the AVIC base address from devicetree
  ARM: imx3: Retrieve the CCM base address from devicetree
  ARM: imx31: Retrieve the IIM base address from devicetree
  ARM: imx27: Retrieve the CCM base address from devicetree
  ARM: imx27: Retrieve the SYSCTRL base address from devicetree
  ARM: s3c64xx: bring back notes from removed debug-macro.S
  ARM: s3c24xx: fix Wunused-variable warning on !MMU
  ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
  MAINTAINERS: mark linux-samsung-soc list non-moderated
  ARM: imx: Remove remnant board file support pieces
  ...

Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC fixes from Olof Johansson:
"I had queued up a batch of fixes that got a bit close to the release
  for sending in before the merge window opened, so I'm including them
  in the merge window batch instead.

  Mostly smaller DT tweaks and fixes, the usual mix that we tend to have
  through the releases"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: dts: iwg20d-q7-common: Fix touch controller probe failure
  ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
  ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
  soc: actions: include header to fix missing prototype
  arm64: dts: ti: k3-j721e: Rename mux header and update macro names
  soc: qcom: pdr: Fixup array type of get_domain_list_resp message
  arm64: dts: qcom: pm660: Fix missing pound sign in interrupt-cells
  arm64: dts: qcom: kitakami: Temporarily disable SDHCI1
  arm64: dts: sdm630: Temporarily disable SMMUs by default
  arm64: dts: sdm845: Fixup OPP table for all qup devices
  arm64: dts: allwinner: h5: remove Mali GPU PMU module
  ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
  soc: xilinx: Fix error code in zynqmp_pm_probe()

KVM: ioapic: break infinite recursion on lazy EOI

During shutdown the IOAPIC trigger mode is reset to edge triggered
while the vfio-pci INTx is still registered with a resampler.
This allows us to get into an infinite loop:

ioapic_set_irq
  -> ioapic_lazy_update_eoi
  -> kvm_ioapic_update_eoi_one
  -> kvm_notify_acked_irq
  -> kvm_notify_acked_gsi
  -> (via irq_acked fn ptr) irqfd_resampler_ack
  -> kvm_set_irq
  -> (via set fn ptr) kvm_set_ioapic_irq
  -> kvm_ioapic_set_irq
  -> ioapic_set_irq

Commit 8be8f932e3db ("kvm: ioapic: Restrict lazy EOI update to
edge-triggered interrupts", 2020-05-04) acknowledges that this recursion
loop exists and tries to avoid it at the call to ioapic_lazy_update_eoi,
but at this point the scenario is already set, we have an edge interrupt
with resampler on the same gsi.

Fortunately, the only user of irq ack notifiers (in addition to resamplefd)
is i8254 timer interrupt reinjection.  These are edge-triggered, so in
principle they would need the call to kvm_ioapic_update_eoi_one from
ioapic_lazy_update_eoi, but they already disable AVIC(*), so they don't
need the lazy EOI behavior.  Therefore, remove the call to
kvm_ioapic_update_eoi_one from ioapic_lazy_update_eoi.

This fixes CVE-2020-27152.  Note that this issue cannot happen with
SR-IOV assigned devices because virtual functions do not have INTx,
only MSI.

Fixes: f458d039db7e ("kvm: ioapic: Lazy update IOAPIC EOI")
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM: vmx: rename pi_init to avoid conflict with paride

allyesconfig results in:

ld: drivers/block/paride/paride.o: in function `pi_init':
(.text+0x1340): multiple definition of `pi_init'; arch/x86/kvm/vmx/posted_intr.o:posted_intr.c:(.init.text+0x0): first defined here
make: *** [Makefile:1164: vmlinux] Error 1

because commit:

commit 8888cdd0996c2d51cd417f9a60a282c034f3fa28
Author: Xiaoyao Li <xiaoyao.li@intel.com>
Date: Wed Sep 23 11:31:11 2020 -0700

KVM: VMX: Extract posted interrupt support to separate files

added another pi_init(), though one already existed in the paride code.

Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build

Replace a modulo operator with the more common pattern for computing the
gfn "offset" of a huge page to fix an i386 build error.

arch/x86/kvm/mmu/tdp_mmu.c:212: undefined reference to `__umoddi3'

In fact, almost all of tdp_mmu.c can be elided on 32-bit builds, but
that is a much larger patch.

Fixes: 2f2fad0897cb ("kvm: x86/mmu: Add functions to handle changed TDP SPTEs")
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20201024031150.9318-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

cifs: update internal module version number

To 2.29

Signed-off-by: Steve French <stfrench@microsoft.com>

Merge tag 'xfs-5.10-merge-7' of git://git./fs/xfs/xfs-linux

Pull xfs fixes from Darrick Wong:
"Two bug fixes that trickled in during the merge window:

   - Make fallocate check the alignment of its arguments against the
     fundamental allocation unit of the volume the file lives on, so
     that we don't trigger the fs' alignment checks.

   - Cancel unprocessed log intents immediately when log recovery fails,
     to avoid a log deadlock"

* tag 'xfs-5.10-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: cancel intents immediately if process_intents fails
  xfs: fix fallocate functions when rtextsize is larger than 1

Merge tag 'docs-5.10-2' of git://git.lwn.net/linux

Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes"

* tag 'docs-5.10-2' of git://git.lwn.net/linux:
  docs: Add two missing entries in vm sysctl index
  docs/vm: trivial fixes to several spelling mistakes
  docs: submitting-patches: describe preserving review/test tags
  Documentation: Chinese translation of Documentation/arm64/hugetlbpage.rst
  Documentation: x86: fix a missing word in x86_64/mm.rst.
  docs: driver-api: remove a duplicated index entry
  docs: lkdtm: Modernize and improve details
  docs: deprecated.rst: Expand str*cpy() replacement notes
  docs/cpu-load: format the example code.

Merge tag 'trace-v5.10-3' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing ring-buffer fix from Steven Rostedt:
"The success return value of ring_buffer_resize() is stated to be
  zero and checked that way.

  But it was incorrectly returning the size allocated.

  Also, a fix to a comment"

* tag 'trace-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ring-buffer: Update the description for ring_buffer_wait
  ring-buffer: Return 0 on success from ring_buffer_resize()

Merge tag 'acpi-5.10-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm

Pull more ACPI updates from Rafael Wysocki:
"These include an ACPICA code build fix related to recent GPE register
  access changes, a Kconfig cleanup related to the Dynamic Platform and
  Thremal Framework (DPTF) support, a reboot issue workaround, a debug
  module fix and a couple of janitorial changes.

  Specifics:

   - Fix ACPICA code build after recent changes related to accessing GPE
     registers (Rafael Wysocki).

   - Clean up DPTF part of the ACPI Kconfig (Rafael Wysocki).

   - Work around a reboot issue related to RESET_REG (Zhang Rui).

   - Prevent ACPI debug module from attemtping to run (and crashing)
     when ACPI is disabled (Jamie Iles).

   - Drop confusing comment from the ACPI processor driver (Alex Hung).

   - Drop a few unreachable break statements (Tom Rix)"

* tag 'acpi-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: utils: remove unreachable breaks
  ACPICA: Add missing type casts in GPE register access code
  ACPI: DPTF: Add ACPI_DPTF Kconfig menu
  ACPI: DPTF: Fix participant driver names
  ACPI: processor: remove comment regarding string _UID support
  ACPI: reboot: Avoid racing after writing to ACPI RESET_REG
  ACPI: debug: don't allow debugging when ACPI is disabled