Todor Tomov [Wed, 25 Jul 2018 16:38:41 +0000 (12:38 -0400)]
media: camss: Add support for 10-bit grayscale formats
Add support for 10-bit packed V4L2_PIX_FMT_Y10P (on 8x16 and 8x96)
and unpacked V4L2_PIX_FMT_Y10 (on 8x96 only) pixel formats.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:40 +0000 (12:38 -0400)]
media: camss: Add support for RAW MIPI14 on 8x96
Add support for RAW MIPI14 format for RDI mode on 8x96.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:39 +0000 (12:38 -0400)]
media: camss: csid: MIPI10 to Plain16 format conversion
Use the PRDI mode on 8x96 to allow to configure RAW MIPI10
to Plain16 format conversion.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:38 +0000 (12:38 -0400)]
media: camss: csid: Different format support on source pad
Usually the format on the source pad is the same as on the sink pad.
However the CSID is able to do some format conversions. To support
this make the format on the source pad selectable amongst a list
of formats. This list can be different for each sink pad format.
This is still not used but will be when the format conversions
are implemented.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:37 +0000 (12:38 -0400)]
media: camss: vfe: Add support for UYVY output from VFE on 8x96
Add support to output UYVY formats from the VFE (via the PIX interface).
A configuration for the realign module in the VFE is added. As the
realign module is present on 8x96 but not on 8x16, this is supported
on 8x96 only.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:36 +0000 (12:38 -0400)]
media: camss: vfe: Different format support on source pad
Rework the format selection on the source pad. Make the format
on the source pad selectable amongst a list of formats. This
list can be different for each sink pad format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:35 +0000 (12:38 -0400)]
media: camss: Format configuration per hardware version
As the 8x16 and 8x96 support different formats, separate the
arrays which contain the supported formats. For the VFE also
add separate arrays for RDI and PIX subdevices.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:34 +0000 (12:38 -0400)]
media: camss: vfe: Add support for 8x96
Add VFE hardware dependent part for 8x96.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:33 +0000 (12:38 -0400)]
media: camss: vfe: Split to hardware dependent and independent parts
This will allow to add support for different hardware.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:32 +0000 (12:38 -0400)]
media: camss: ispif: Add support for 8x96
ISPIF hardware modules on 8x16 and 8x96 are similar. However on
8x96 the ISPIF routes data to two VFE hardware modules. Add
separate interrupt handler for 8x96 to handle the additional
interrupts.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:31 +0000 (12:38 -0400)]
media: camss: csid: Add support for 8x96
CSID hardware modules on 8x16 and 8x96 are similar. There is no
need to duplicate the code by adding separate versions. Just
update the register macros to return the correct register
addresses.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:30 +0000 (12:38 -0400)]
media: camss: csiphy: Add support for 8x96
Add CSIPHY hardware dependent part for 8x96.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:29 +0000 (12:38 -0400)]
media: camss: csiphy: Unify lane handling
Restructure lane configuration so it is simpler and will allow
similar (although not the same) handling for different hardware
versions.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:28 +0000 (12:38 -0400)]
media: camss: csiphy: Split to hardware dependent and independent parts
This will allow to add support for different hardware.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
[hans.verkuil@cisco.com: remove trailing empty line]
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:27 +0000 (12:38 -0400)]
media: camss: Add basic runtime PM support
There is a PM domain for each of the VFE hardware modules. Add
support for basic runtime PM support to be able to control the
PM domains. When a PM domain needs to be powered on - a device
link is created. When a PM domain needs to be powered off -
its device link is removed. This allows separate and
independent control of the PM domains.
Suspend/Resume is still not supported.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:26 +0000 (12:38 -0400)]
media: camss: Add 8x96 resources
Add structs with 8x96 resources. As the number of CSIPHY, CSID
and VFE hardware modules is different on 8x16 and 8x96 select
the number at runtime and allocate needed structures
dynamically.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:25 +0000 (12:38 -0400)]
media: dt-bindings: media: qcom,camss: Add 8996 bindings
Update binding document for MSM8996.
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:24 +0000 (12:38 -0400)]
media: dt-bindings: media: qcom,camss: Fix whitespaces
Use tabs.
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:23 +0000 (12:38 -0400)]
media: camss: vfe: Do not disable CAMIF when clearing its status
Use "no change" value when clearing CAMIF status and make sure
this is done before configuring the new command.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:22 +0000 (12:38 -0400)]
media: camss: vfe: Get line pointer as container of video_out
Simplify getting of the line pointer by using the container_of
macro instead of traversing media controller links.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:21 +0000 (12:38 -0400)]
media: camss: vfe: Fix to_vfe() macro member name
Use the member name which is "line" instead of the pointer argument.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:20 +0000 (12:38 -0400)]
media: camss: csid: Configure data type and decode format properly
The CSID decodes the input data stream. When the input comes from
the Test Generator the format of the stream is set on the source
media pad. When the input comes from the CSIPHY the format is the
one on the sink media pad. Use the proper format for each case.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:19 +0000 (12:38 -0400)]
media: camss: csiphy: Update settle count calculation
Update settle count calculation as per specification.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:18 +0000 (12:38 -0400)]
media: camss: Unify the clock names
Use more logical clock names - similar to the names in documentation.
This will allow better handling of the clocks in the driver when support
for more hardware versions is added - equivalent clocks on different
hardware versions will have the same name.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Tue, 31 Jul 2018 06:19:43 +0000 (02:19 -0400)]
media: dt-bindings: media: qcom, camss: Unify the clock names
Use more logical clock names - similar to the names in documentation.
This will allow better handling of the clocks in the driver when support
for more hardware versions is added - equivalent clocks on different
hardware versions will have the same name.
Note: No dts is using this device (and clock names) yet.
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:16 +0000 (12:38 -0400)]
media: camss: csiphy: Ensure clock mux config is done before the rest
Add a write memory barier after clock mux config and before the rest
of the csiphy config.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:15 +0000 (12:38 -0400)]
media: camss: Fix OF node usage
of_graph_get_next_endpoint increases the refcount of the returned
node and decreases the refcount of the passed node. Take this into
account and use of_node_put properly.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:14 +0000 (12:38 -0400)]
media: camss: Use SPDX license headers
Use SPDX license headers for all files of the Qualcomm CAMSS driver.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:13 +0000 (12:38 -0400)]
media: Rename CAMSS driver path
Support for camera subsystem on QComm MSM8996/APQ8096 is to be added
so remove hardware version from CAMSS driver's path.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:12 +0000 (12:38 -0400)]
media: v4l: Add new 10-bit packed grayscale format
The new format will be called V4L2_PIX_FMT_Y10P.
It is similar to the V4L2_PIX_FMT_SBGGR10P family formats
but V4L2_PIX_FMT_Y10P is a grayscale format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Todor Tomov [Wed, 25 Jul 2018 16:38:11 +0000 (12:38 -0400)]
media: v4l: Add new 2X8 10-bit grayscale media bus code
The code will be called MEDIA_BUS_FMT_Y10_2X8_PADHI_LE.
It is similar to MEDIA_BUS_FMT_SBGGR10_2X8_PADHI_LE
but MEDIA_BUS_FMT_Y10_2X8_PADHI_LE describes grayscale
data.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sakari Ailus [Wed, 25 Jul 2018 16:38:10 +0000 (12:38 -0400)]
media: doc-rst: Add packed Bayer raw14 pixel formats
These formats are compressed 14-bit raw bayer formats with four different
pixel orders. They are similar to 10-bit variants. The formats added by
this patch are
V4L2_PIX_FMT_SBGGR14P
V4L2_PIX_FMT_SGBRG14P
V4L2_PIX_FMT_SGRBG14P
V4L2_PIX_FMT_SRGGB14P
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Robert Schlabbach [Mon, 25 Jun 2018 10:33:58 +0000 (06:33 -0400)]
media: em28xx: disable null packet filter for WinTVdualHD
This patch disables the null packet filter for the Hauppauge
WinTV-dualHD. There are applications which require the unfiltered
transport stream (e.g. DOCSIS segment load analyzers).
Tests showed that the device is capable of delivering two unfiltered
EuroDOCSIS 3.0 transport streams simultaneously, i.e. over 100 Mbit/s
worth of data, without any losses.
Signed-off-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sun, 24 Jun 2018 13:42:50 +0000 (09:42 -0400)]
media: dvb-frontends/tda18271c2dd: fix handling of DVB-T parameters
Add a break statement in set_params() for the SYS_DVBT(2).
As reported by gcc:
drivers/media/dvb-frontends/tda18271c2dd.c:1144:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
There is a nested switch() inside the code with sets the tuner to
the right standard. Without the break, the code will always set to
DVB-C mode, with can be sub-optimal for DVB-T.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:15 +0000 (11:36 -0400)]
media: ddbridge/mci: add SX8 I/Q mode remark and remove DIAG CMD defines
Take note that the SX8 IQ mode is only available on a single tuner, and
remove the MCI/SX8 DIAG CMD defines.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:14 +0000 (11:36 -0400)]
media: ddbridge/sx8: enable modulation selection in set_parameters()
Allow for tuning to transponders with specific modulations in
set_parameters(). Setting a specific modulation will also enable lower
modulations.
Picked up from the upstream dddvb GIT. Upstream also has support for
APSK64/128/256 modulations which aren't supported yet by the DVB
API, so comment them out until support for them is added.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:13 +0000 (11:36 -0400)]
media: ddbridge/sx8: disable automatic PLS code search
The SX8 cards by default do an automatic search for the PLS code. This
is not necessarily wanted as this can eventually be detected wrong, so
disable this.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:12 +0000 (11:36 -0400)]
media: ddbridge/mci: add more MCI status codes, improve MCI_SUCCESS macro
The MCI can report the command status more finegrained, so, add more
status code defines and update the MCI_SUCCESS macro.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:11 +0000 (11:36 -0400)]
media: ddbridge/mci: split MaxSX8 specific code off to ddbridge-sx8.c
Split off all code specific to the MaxSX8 cards to a separate ddbridge-sx8
module and hook it up in the Makefile. This also adds evaluation of the
mci_type to allow for using different attach handling for different cards.
As different cards can implement things differently (ie. support differing
frontend_ops, and have different base structs being put ontop of the
common mci_base struct), this introduces the mci_cfg struct which is
initially used to hold a few specifics to the -sx8 submodule. While at it,
the handling of the i/q mode is adjusted slightly. Besides this and
handling mci_base and sx8_base struct pointers where needed, all code
is copied unmodified from ddbridge-mci.c.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:10 +0000 (11:36 -0400)]
media: ddbridge/mci: make ddb_mci_cmd() and ddb_mci_config() public
In preparation for splitting all MaxSX8 related code parts from the common
MCI code, prefix both mci_cmd() and mci_config() functions with ddb_,
remove the static marking and add matching function prototypes to
ddbridge-mci.h so these functions can be reused from other files within
the ddbridge driver. As this requires the mci-related structs to be
defined in ddbridge-mci.h, move struct mci and struct mci_base there and
clean them up.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:09 +0000 (11:36 -0400)]
media: ddbridge/mci: store mci type and number of ports in the hwinfo
For better support for future MCI based cards, rename the mci struct
member to mci_ports to carry the number of ports on the cards, and add a
mci_type member to identify the card type to handle differing hardware.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:08 +0000 (11:36 -0400)]
media: ddbridge/mci: extend mci_command and mci_result structs
Recent FPGA firmware reports more data and values in sent command
responses. Adjust the mci_command and mci_result structs including it's
unions to match these changes and add a few comments explaining things.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:07 +0000 (11:36 -0400)]
media: ddbridge/mci: rename defines and fix i/q var types
Adjustments to match the FPGA firmware, and the signal I/Q values are
reported as s16 types from the card firmware.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:06 +0000 (11:36 -0400)]
media: ddbridge/mci: read and report signal strength and SNR
Implement querying signal statistics from the MCI and report this data
in read_status() as DVBv5 statistics.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:05 +0000 (11:36 -0400)]
media: ddbridge/mci: update copyright year in headers
Update the copyright year information in the MCI headers to 2017-2018.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:04 +0000 (11:36 -0400)]
media: ddbridge: change MCI base ID and define a SX8 ID
Change the start of the MCI ID range (internally used only) to 48 and
define an ID for the SX8 card type. Use this new ID to handle device
attachment.
This change is done in preparation for support of more MCI based cards.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:03 +0000 (11:36 -0400)]
media: ddbridge: link structure access cosmetics in ddb_port_probe()
Throughout the function, dev->link[l] is used several times. Unclutter
this a bit by declaring a ddb_link var at the top of the function, assign
the address of dev->link[l] to it and use that var to access the link[]
struct member.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:02 +0000 (11:36 -0400)]
media: ddbridge: remove unused MDIO defines and hwinfo member
ddbridge has a few MDIO related remainders (defines, hwinfo struct) which
aren't of any use for the in-kernel driver at all (they're only used in
conjunction with the OctoNet SAT>IP boxes which the kernel driver doesn't
have any support for), so clean this up.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:01 +0000 (11:36 -0400)]
media: ddbridge: report I2C bus errors
The I2C_COMMAND response reports an error in the I2C bus communication
using bit 17. Evaluate the response more thoroughly and log an error
if an I2C problem was detected.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:36:00 +0000 (11:36 -0400)]
media: ddbridge: evaluate the actual link when setting up the dummy tuner
Devices supporting dummy tuner operation can exist on any link, not only
on link 0, so fix this accordingly.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:35:59 +0000 (11:35 -0400)]
media: ddbridge: probe for LNBH25 chips before attaching
In demod_attach_stv0910(), the LNBH25 IC is being blindly attached and,
if the result is bad, blindly attached on another possible I2C address.
The LNBH25 uses it's set_voltage function to test for the IC and will
print an error to the kernel log on failure. Prevent this by probing
the possible I2C address and use this (and only this) to attach the
LNBH25 I2C driver. This also allows the stv0910 attach function to be
a bit cleaner.
Picked up from the upstream dddvb GIT and adapted for the LNBH25 driver
variant from the kernel tree.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 23 Jun 2018 15:35:58 +0000 (11:35 -0400)]
media: dvb-frontends/stv0910: cast the BER denominator shift exp to ULL
To avoid miscalculations related to the BER denominator, the shift
expression needs to be casted as ULL.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mauro Carvalho Chehab [Wed, 30 May 2018 15:07:04 +0000 (11:07 -0400)]
media: dvb/audio.h: get rid of unused APIs
There are a number of other ioctls that aren't used anywhere
inside the Kernel tree.
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mauro Carvalho Chehab [Wed, 30 May 2018 15:07:03 +0000 (11:07 -0400)]
media: dvb/video.h: get rid of unused APIs
There are a number of other ioctls that aren't used anywhere
inside the Kernel tree.
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mauro Carvalho Chehab [Wed, 30 May 2018 15:07:05 +0000 (11:07 -0400)]
media: videodev2: get rid of VIDIOC_RESERVED
While this ioctl is there at least since Kernel 2.6.12-rc2, it
was never used by any upstream driver.
Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Robert Schlabbach [Sat, 16 Jun 2018 19:04:22 +0000 (15:04 -0400)]
media: em28xx: explicitly disable TS packet filter
The em28xx driver never touched the EM2874 register bits that control
the transport stream packet filters, leaving them at whatever default
the firmware has set. E.g. the Pinnacle 290e disables them by default,
while the Hauppauge WinTV dualHD enables discarding NULL packets by
default.
However, some applications require NULL packets, e.g. to determine the
load in DOCSIS segments, so discarding NULL packets is undesired for
such applications.
This patch simply extends the bit mask when starting or stopping the
transport stream packet capture, so that the filter bits are cleared.
It has been verified that this makes the Hauppauge WinTV dualHD pass
an unfiltered DVB-C stream including NULL packets, which it didn't
before.
Signed-off-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Akihiro Tsukada [Sun, 10 Jun 2018 14:59:31 +0000 (10:59 -0400)]
MAINTAINERS: add entries for several media drivers
add entries for the following drivers:
- earth_pt{1,3} DVB adapter drivers
- mxl301rf DVB tuner drivers
- qm1d1{b0004, c0042} DVB tuner drivers
- tc90522 DVB demod driver
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Akihiro Tsukada [Sun, 10 Jun 2018 14:58:02 +0000 (10:58 -0400)]
media: pci/pt1: suppress compiler warning in xtensa arch
Found and reported by kbuild test robot:
Message ID: <
201805052003.MC007f9h%fengguang.wu@intel.com>
and holding an address of an empty struct in .driver.pm does no harm
when CONFIG_PM_SLEEP is not defined.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Akihiro Tsukada [Sun, 10 Jun 2018 14:49:15 +0000 (10:49 -0400)]
media: dvb-frontends/dvb-pll: fix module ref-counting
dvb-pll module was 'put' twice on exit:
once by dvb_frontend_detach() and another by dvb_module_release().
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Akihiro Tsukada [Sun, 10 Jun 2018 14:45:31 +0000 (10:45 -0400)]
media: dvb-usb/friio, dvb-usb-v2/gl861: decompose friio and merge with gl861
Friio device contains "gl861" bridge and "tc90522" demod,
for which the separate drivers are already in the kernel.
But friio driver was monolithic and did not use them,
practically copying those features.
This patch decomposes friio driver into sub drivers and
re-uses existing ones, thus reduces some code.
It adds some features to gl861,
to support the friio-specific init/config of the devices
and implement i2c communications to the tuner via demod
with USB vendor requests.
[mchehab+samsung@kernel.org: fix merge conflicts]
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Corentin Labbe [Thu, 7 Jun 2018 19:55:25 +0000 (15:55 -0400)]
media: sii9234: remove unused header
The include/linux/platform_data/media/sii9234.h header file is unused,
let's remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sylwester Nawrocki [Tue, 5 Jun 2018 13:33:59 +0000 (09:33 -0400)]
media: s5p-mfc: Fix buffer look up in s5p_mfc_handle_frame_{new, copy_time} functions
Look up of buffers in s5p_mfc_handle_frame_new, s5p_mfc_handle_frame_copy_time
functions is not working properly for DMA addresses above 2 GiB. As a result
flags and timestamp of returned buffers are not set correctly and it breaks
operation of GStreamer/OMX plugins which rely on the CAPTURE buffer queue
flags.
Due to improper return type of the get_dec_y_adr, get_dspl_y_adr callbacks
and sign bit extension these callbacks return incorrect address values,
e.g. 0xfffffffffefc0000 instead of 0x00000000fefc0000. Then the statement:
"if (vb2_dma_contig_plane_dma_addr(&dst_buf->b->vb2_buf, 0) == dec_y_addr)"
is always false, which breaks looking up capture queue buffers.
To ensure proper matching by address u32 type is used for the DMA
addresses. This should work on all related SoCs, since the MFC DMA
address width is not larger than 32-bit.
Changes done in this patch are minimal as there is a larger patch series
pending refactoring the whole driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ezequiel Garcia [Wed, 25 Jul 2018 17:15:12 +0000 (13:15 -0400)]
media: v4l2-mem2mem: Fix missing v4l2_m2m_try_run call
Commit
34dbb848d5e4 ("media: mem2mem: Remove excessive try_run call")
removed a redundant call to v4l2_m2m_try_run but instead introduced
a bug. Consider the following case:
1) Context A schedules, queues and runs job A.
2) While the m2m device is running, context B schedules
and queues job B. Job B cannot run, because it has to
wait for job A.
3) Job A completes, calls v4l2_m2m_job_finish, and tries
to queue a job for context A, but since the context is
empty it won't do anything.
In this scenario, queued job B will never run. Fix this by calling
v4l2_m2m_try_run from v4l2_m2m_try_schedule.
While here, add more documentation to these functions.
Fixes:
34dbb848d5e4 ("media: mem2mem: Remove excessive try_run call")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: split >80 cols line]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Luca Ceresoli [Wed, 25 Jul 2018 16:24:55 +0000 (12:24 -0400)]
media: imx274: add cropping support via SELECTION API
Currently this driver does not support cropping. The supported modes
are the following, all capturing the entire area:
- 3840x2160, 1:1 binning (native sensor resolution)
- 1920x1080, 2:1 binning
- 1280x720, 3:1 binning
The VIDIOC_SUBDEV_S_FMT ioctl chooses among these 3 configurations the
one that matches the requested format.
Add cropping support via VIDIOC_SUBDEV_S_SELECTION: with target
V4L2_SEL_TGT_CROP to choose the captured area, with
V4L2_SEL_TGT_COMPOSE to choose the output resolution.
To maintain backward compatibility we also allow setting the compose
format via VIDIOC_SUBDEV_S_FMT. To obtain this, compose rect and
output format are computed in the common helper function
__imx274_change_compose(), which sets both to the same width/height
values.
Cropping also calls __imx274_change_compose() whenever cropping rect
size changes in order to reset the compose rect (and output format
size) for 1:1 binning.
Also rename enum imx274_mode to imx274_binning (and its values from
IMX274_MODE_BINNING_* to IMX274_BINNING_*). Without cropping, the two
naming are equivalent. With cropping, the resolution could be
different, e.g. using 2:1 binning mode to crop 1200x960 and output a
600x480 format. Using binning in the names avoids any
misunderstanding. For the same reason, replace the 'size' field in
struct imx274_frmfmt with 'bin_ratio'.
[Sakari Ailus: Remove leftover condition in imx274_apply_trimming]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Luca Ceresoli [Wed, 25 Jul 2018 16:24:54 +0000 (12:24 -0400)]
media: imx274: use regmap_bulk_write to write multybyte registers
Currently 2-bytes and 3-bytes registers are set by very similar
functions doing the needed shift & mask manipulation, followed by very
similar for loops setting one byte at a time over I2C.
Replace all of this code by a unique helper function that calls
regmap_bulk_write(), which has two advantages:
- sets all the bytes in a unique I2C transaction
- removes lots of now unused code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rui Miguel Silva [Tue, 3 Jul 2018 14:08:03 +0000 (10:08 -0400)]
media: ov2680: Add Omnivision OV2680 sensor driver
This patch adds V4L2 sub-device driver for OV2680 image sensor.
The OV2680 is a 1/5" CMOS color sensor from Omnivision.
Supports output format: 10-bit Raw RGB.
The OV2680 has a single lane MIPI interface.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- exposure,
- auto/manual gain,
- gain,
- horizontal/vertical flip,
- test pattern menu.
Supported resolution are only: QUXGA, 720P, UXGA.
[Sakari Ailus: Drop "-level" from Kconfig help text]
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rui Miguel Silva [Tue, 3 Jul 2018 14:08:02 +0000 (10:08 -0400)]
media: ov2680: dt: Add bindings for OV2680
Add device tree binding documentation for the OV2680 camera sensor.
[Sakari Ailus: Squash MAINTAINERS entry from Rui]
CC: devicetree@vger.kernel.org
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jacopo Mondi [Wed, 25 Jul 2018 13:44:31 +0000 (09:44 -0400)]
media: i2c: Add driver for Aptina MT9V111
Add V4L2 sensor driver for Aptina MT9V111 CMOS image sensor.
The MT9V111 is a 1/4-Inch CMOS image sensor based on MT9V011 with an
integrated Image Flow Processor.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jacopo Mondi [Wed, 25 Jul 2018 13:44:30 +0000 (09:44 -0400)]
media: dt-bindings: media: i2c: Document MT9V111 bindings
Add documentation for Aptina MT9V111 image sensor.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sakari Ailus [Fri, 20 Jul 2018 21:07:15 +0000 (17:07 -0400)]
media: dw9807-vcm: Recognise this is just the VCM bit of the device
The dw9807 contains a voice coil lens driver as well as an EEPROM. This
driver is just for the VCM. Reflect this in the driver's name --- this is
already the case for the compatible string, for instance.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Niklas Söderlund [Thu, 26 Jul 2018 22:36:57 +0000 (18:36 -0400)]
media: rcar-csi2: update stream start for V3M
Latest errata document updates the start procedure for V3M. This change
in addition to adhering to the datasheet update fixes capture on early
revisions of V3M.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:44:24 +0000 (23:44 -0400)]
media: pci: ivtv: Replace GFP_ATOMIC with GFP_KERNEL
ivtv_probe() and ivtvfb_init_card() are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:41:50 +0000 (23:41 -0400)]
media: pci: cx88: Replace mdelay() with msleep() in dvb_register()
dvb_register() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:38:23 +0000 (23:38 -0400)]
media: pci: cx88: Replace mdelay() with msleep() in cx88_card_setup_pre_i2c()
cx88_card_setup_pre_i2c() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:22:09 +0000 (23:22 -0400)]
media: pci: cx25821: Replace mdelay() with msleep()
cx25821_gpio_init(), cx25821_initialize() and cx25821_registers_init()
are never called in atomic context.
They call mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:18:46 +0000 (23:18 -0400)]
media: pci: cx23885: Replace mdelay() with msleep() in cx23885_reset()
cx23885_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:15:34 +0000 (23:15 -0400)]
media: pci: cx23885: Replace mdelay() with msleep() and usleep_range() in cx23885_gpio_setup()
cx23885_gpio_setup() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:09:46 +0000 (23:09 -0400)]
media: pci: cx23885: Replace mdelay() with msleep() and usleep_range() in altera_ci_slot_reset()
altera_ci_slot_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:07:04 +0000 (23:07 -0400)]
media: pci: cobalt: Replace GFP_ATOMIC with GFP_KERNEL in cobalt_probe()
cobalt_probe() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 03:02:40 +0000 (23:02 -0400)]
media: i2c: vs6624: Replace mdelay() with msleep() and usleep_range() in vs6624_probe()
vs6624_probe() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai [Fri, 27 Jul 2018 02:58:43 +0000 (22:58 -0400)]
media: i2c: adv7842: Replace mdelay() with msleep() and usleep_range() in adv7842_ddr_ram_test()
adv7842_ddr_ram_test() is never called in atomic context.
It only calls from:
adv7842_ddr_ram_test() <- adv7842_command_ram_test() <- adv7842_ioctl()
adv7842_ddr_ram_test() calls mdelay() to busily wait,
which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Matt Ranostay [Fri, 27 Jul 2018 01:47:24 +0000 (21:47 -0400)]
media: video-i2c: hwmon: fix return value from amg88xx_hwmon_init()
PTR_ERR was making any pointer passed an error pointer, and should be
replaced with PTR_ERR_OR_ZERO which checks if is an actual error condition.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Niklas Söderlund [Thu, 26 Jul 2018 10:27:16 +0000 (06:27 -0400)]
media: adv7180: add g_frame_interval support
Implement g_frame_interval to return the current standard's frame
interval.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Niklas Söderlund [Thu, 26 Jul 2018 10:27:15 +0000 (06:27 -0400)]
media: adv7180: fix field type to V4L2_FIELD_ALTERNATE
The ADV7180 and ADV7182 transmit whole fields, bottom field followed
by top (or vice-versa, depending on detected video standard). So
for chips that do not have support for explicitly setting the field
mode via I2P, set the field mode to V4L2_FIELD_ALTERNATE.
I2P converts fields into frames using an edge adaptive algorithm. The
frame rate is the same as the 'field rate': e.g. X fields per second
are now X frames per second.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ezequiel Garcia [Wed, 25 Jul 2018 21:01:23 +0000 (17:01 -0400)]
media: rockchip/rga: Fix bad dma_free_attrs() parameter
In rga_remove(), dma_free_attrs is being passed the wrong
cpu address, which triggers an exception if the driver is
removed. Fix it.
Tested on a RK3399 platform, with a bind/unbind cycle.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Wed, 25 Jul 2018 12:51:39 +0000 (08:51 -0400)]
media: media.h: remove linux/version.h include
The media.h public header is one of only three public headers that include
linux/version.h. Drop it from media.h. It was only used for an obsolete
define.
It has to be added to media-device.c, since that source relied on media.h
to include it.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Nicolas Dufresne [Fri, 20 Jul 2018 14:09:16 +0000 (10:09 -0400)]
media: vivid: Fix V4L2_FIELD_ALTERNATE new frame check
The vivid driver will overlay stream time on generated frames. Though,
in interlacing mode V4L2_FIELD_ALTERNATE, each field is separate and
must have the same time to ensure proper render. Though, this time was
only updated every 2 frames as the code was checking against the wrong
counter (frame counter rather then field counter).
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mauro Carvalho Chehab [Fri, 27 Jul 2018 11:01:03 +0000 (07:01 -0400)]
media: media.h.rst.exceptions: ignore MEDIA-ENT-F-DTV-DECODER
This was kept just for backward compatibility. Solves this warning:
media.h.rst:6: WARNING: undefined label: media-ent-f-dtv-decoder (if the link has no caption the label must precede a section header)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Thu, 19 Jul 2018 10:45:10 +0000 (06:45 -0400)]
media: coda: add SPS fixup code for frame sizes that are not multiples of 16
The CODA7541 firmware does not set the SPS frame cropping fields to
properly describe coded h.264 streams with frame sizes that are not a
multiple of the macroblock size.
This adds RBSP parsing code and a SPS fixup routine to manually replace
the cropping information in the headers produced by the firmware with
the correct values.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[hans.verkuil@cisco.com: added explanation of SPS RBSP to comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Thu, 19 Jul 2018 10:42:28 +0000 (06:42 -0400)]
media: coda: let CODA960 firmware set frame cropping in SPS header
When encoding h.264, if visible resolution is not aligned to macroblock
size, frame cropping has to be set in the SPS header to produce correct
streams. The CODA960 firmware can do this on its own if asked to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Fri, 27 Jul 2018 10:40:45 +0000 (06:40 -0400)]
media: media-types.rst: fix doc warnings
Fix these warnings when building the documentation:
media.h.rst:6: WARNING: undefined label: media-ent-f-dv-decoder (if the link has no caption the label must precede a section header)
media.h.rst:6: WARNING: undefined label: media-ent-f-dv-encoder (if the link has no caption the label must precede a section header)
media.h.rst:6: WARNING: undefined label: media-ent-f-dv-decoder (if the link has no caption the label must precede a section header)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Katsuhiro Suzuki [Tue, 29 May 2018 01:09:20 +0000 (21:09 -0400)]
media: helene: fix xtal frequency setting at power on
This patch fixes crystal frequency setting when power on this device.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kieran Bingham [Mon, 28 May 2018 10:24:20 +0000 (06:24 -0400)]
media: vsp1: Document vsp1_dl_body refcnt
In commit
2d9445db0ee9 ("media: vsp1: Use reference counting for
bodies"), a new field was introduced to the vsp1_dl_body structure to
account for usage tracking of the body.
Document the newly added field in the kerneldoc.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mauro Carvalho Chehab [Mon, 28 May 2018 14:32:41 +0000 (10:32 -0400)]
media: dvb: get rid of VIDEO_SET_SPU_PALETTE
No upstream drivers use it. It doesn't make any sense to have
a compat32 code for something that nobody uses upstream.
Reported-by: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Guennadi Liakhovetski [Thu, 26 Jul 2018 08:17:53 +0000 (04:17 -0400)]
media: uvcvideo: Send a control event when a Control Change interrupt arrives
UVC defines a method of handling asynchronous controls, which sends a
USB packet over the interrupt pipe. This patch implements support for
such packets by sending a control event to the user. Since this can
involve USB traffic and, therefore, scheduling, this has to be done
in a work queue.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Guennadi Liakhovetski [Tue, 8 May 2018 15:07:44 +0000 (11:07 -0400)]
media: uvcvideo: Handle control pipe protocol STALLs
When a command ends up in a STALL on the control pipe, use the Request
Error Code control to provide a more precise error information to the
user. For example, if a camera is still busy processing a control,
when the same or an interrelated control set request arrives, the
camera can react with a STALL and then return the "Not ready" status
in response to a UVC_VC_REQUEST_ERROR_CODE_CONTROL command. With this
patch the user would then get an EBUSY error code instead of a
generic EPIPE.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Guennadi Liakhovetski [Tue, 8 May 2018 15:07:42 +0000 (11:07 -0400)]
media: uvcvideo: Remove a redundant check
Event subscribers cannot have a NULL file handle. They are only added
at a single location in the code, and the .fh pointer is used without
checking there.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Nicolas Dufresne [Tue, 5 Jun 2018 00:24:15 +0000 (20:24 -0400)]
media: uvcvideo: Also validate buffers in BULK mode
Just like for ISOC, validate the decoded BULK buffer size when possible.
This avoids sending corrupted or partial buffers to userspace, which may
lead to application crash or run-time failure.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
[laurent.pinchart@ideasonboard.com: Move uvc_video_validate_buffer() call to uvc_video_next_buffers()]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Laurent Pinchart [Wed, 21 Mar 2018 09:16:40 +0000 (05:16 -0400)]
media: uvcvideo: Add KSMedia 8-bit IR format support
Add support for the 8-bit IR format GUID defined in the Microsoft Kernel
Streaming Media API.
Reported-by: Paul Menzel <pmenzel+linux-media@molgen.mpg.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Paul Menzel <pmenzel+linux-media@molgen.mpg.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kieran Bingham [Tue, 20 Mar 2018 15:43:08 +0000 (11:43 -0400)]
media: uvcvideo: Fix minor spelling
Provide the missing 't' from straightforward.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
projects / platform / kernel / linux-rpi.git / log