mac80211: remove tx_frags driver callback

The implementation of tx_frags is buggy due to
not handling queue stop, and there's no driver
implementing it so remove it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: include VHT capability IE in probe requests

Insert the VHT capability IE into probe requests.

Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: 60g protocol constants

Provide various constants as defined by the 802.11ad:
frame types, IE's, capability bits, action categories

Introduce GCMP cipher, mandatory by 802.11ad

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: regulatory for 60g

Add regulatory rule for the 60g band

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: add 802.11ad (60gHz band) support

Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.

Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: allow calling ieee80211_ap_probereq_get() during auth/assoc

Drivers might need getting the probe request
(e.g. in order to extract the ssid) even during
auth/assoc.

Make ieee80211_ap_probereq_get() support it
by considering auth_data/assoc_data as well.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: respect iface combinations when starting operation

devlist_mtx locking is changed to accomodate changes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: add channel checking for iface combinations

.connect cannot be handled since the driver scans
and connects on its own. It is up to the driver
then to refuse a connection (with -EBUSY for
example).

Non-fixed channel IBSSes always take a single
channel resource. For example two non-fixed
channel IBSSes always take up 2
num_different_channels, even if they operate on
the same channel at a given point of time.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211/mac80211: remove .get_channel

We do not need it anymore since cfg80211 tracks
monitor channel and monitor channel type.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: set initial monitor channel

Implements behaviour seen in mac80211. A running
monitor always has a channel - even before
.set_channel. This way we won't break current
behaviour.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: track monitor channel

Make it even more obvious we support single
monitor channel. This will allow us to remove
.get_channel.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: refuse to .set_monitor_channel when non-monitors are present

Having .set_monitor_channel work with non-monitor
interfaces running would make interface
combinations accounting ambiguous.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: refactor virtual monitor code

Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: track monitor interfaces count

Implements .set_monitor_enabled(wiphy, enabled).

Notifies driver upon change of interface layout.

If only monitor interfaces become present it is
called with 2nd argument being true. If
non-monitor interface appears then 2nd argument
is false. Driver is notified only upon change.

This makes it more obvious about the fact that
cfg80211 supports single monitor channel. Once we
implement multi-channel we don't want to allow
setting monitor channel while other interface
types are running. Otherwise it would be ambiguous
once we start considering num_different_channels.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: introduce cfg80211_get_chan_state

Helper function for finding out which channel is
used by a given interface.

An exclusive channel can be used only by a single
interface. This is mainly for non-fixed channel
IBSS handling.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: track ibss fixed channel

IBSS may hop between channels. It is necessary to
account this special case when considering
interface combinations.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: add channel tracking for AP and mesh

We need to know which channel is used by a running
AP and mesh for channel context accounting and
finding matching/active interface combination.

STA/IBSS have current_bss already which allows us
to check which channel a vif is tuned to.
Non-fixed channel IBSS can be handled with
additional changes.

Monitor mode is going to be handled differently.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: .stop_ap when interface is going down

We'll need this for proper channel tracking (which
is going to be needed for channel context
accounting and finding matching/active interface
combination).

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: introduce cfg80211_stop_ap

This functionality will be reused when interface
is going down. Avoids code duplication. Also adds
missing wdev locking.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge remote-tracking branch 'wireless-next/master' into mac80211-next

cfg80211: allow advertising VHT capabilities

Allow drivers to advertise their VHT capabilities
and export them to userspace via nl80211.

Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wireless: add VHT (802.11ac) definitions

Add the VHT definitions to be used by drivers supporting it.

Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: don't require associated->beacon_ies for ps

beacon_ies is needed only in order to extract the dtim
period. However, even if it's missing we can still enter
ps with dtim=1 (which also happens if the TIM ie is invalid).

Most drivers don't use conf.max_sleep_period/ps_dtim_period
anyway, and this check prevents them from entering ps if
they don't have beacon (but only probe response), even though
the beacon is not needed at all.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: flush queues before deauth/disassoc

On deauth/disassoc we tear down all BA sessions. These
DELBA packets are sent on the appropriate TID, while
deauth/disassoc is always sent on VO. This sometimes
ends with the DELBA being sent after the deauth was
already sent.

Fix it by flushing all the pending frames before
sending deauth/disassoc.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: don't expose ieee80211_add_srates_ie()

This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.

Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ath9k: Fix compilation breakage

Wrap the MCI-work canceling with CONFIG_ATH9K_BTCOEX_SUPPORT.

Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix sparse warning introduced with checkdied patch

The commit "brcmfmac: introduce checkdied debugfs functionality"
also introduced a sparse warning:

..../brcmfmac/dhd_sdio.c:3147:45: sparse: cast to restricted __le32

This patch fixes this sparse warning.

Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add BCM4334 support

BCM4334 is a dualband a/b/g/n WiFi chip support 20MHz/40MHz
channels. This patch adds support for its SDIO interface.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: reduce allocations needed during nvram data download

The nvram data is preprocessed before being sent to the device
and just before sending an additional allocation was done that
assured word alignment of the data. This has moved to the
preprocessing step to reduce allocations and subsequent copying
of the nvram data.

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use firmware data buffer directly for nvram

The nvram file could be parsed directly in the data buffer in the
firmware structure passed by request_firmware function. This patch
gets rid of the redundant memcpy.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: move glom alignment setting to SDIO bus layer

txglomming alignment is a SDIO bus specific feature. It is more
appropriate to place it in SDIO bus layer instead of common layer.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: restrict dongle txglom disable to old SDIO core

txglomming is a firmware feature for sdio bus interface. For SDIO
device cores newer than revision 11, the default setting of
firmware should be used instead of disabling it from the host side.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add support for bus specific data command

brcmfmac need to support data command setting for dongle's bus
core. A list must be placed at brcmf_bus structure before calling
brcmf_bus_start in order to be sent by brcmf_c_preinit_dcmds.

Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: define some additional cores IDs

Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: don't allow WoWLAN support without CONFIG_PM

When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.

Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge branch 'wl12xx-next' into for-linville

ath9k_htc: Fix IDLE power save

Remove the radio enable/disable stuff and fix the
transition to FULL_SLEEP mode when the device is idle.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Use atomic operations for op_flags

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Change default listen interval to 1

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix lockdep splat

Cancel the MCI work only when MCI is actually enabled.
Fixes this:

[96833.124051] Call Trace:
[96833.124060]  [<ffffffff810afaf8>] __lock_acquire+0x1518/0x1e40
[96833.124065]  [<ffffffff810ad126>] ? mark_held_locks+0x86/0x110
[96833.124069]  [<ffffffff810ad3ad>] ? trace_hardirqs_on+0xd/0x10
[96833.124073]  [<ffffffff814464f0>] ? _raw_spin_unlock_irq+0x30/0x70
[96833.124078]  [<ffffffff81072968>] ? wait_on_cpu_work+0x98/0xc0
[96833.124082]  [<ffffffff810b0a11>] lock_acquire+0xa1/0x150
[96833.124085]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124088]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124092]  [<ffffffff810729e2>] wait_on_work+0x52/0x120
[96833.124095]  [<ffffffff81072990>] ? wait_on_cpu_work+0xc0/0xc0
[96833.124099]  [<ffffffff81063b3f>] ? del_timer+0x7f/0x110
[96833.124102]  [<ffffffff81072c13>] __cancel_work_timer+0x83/0x130
[96833.124106]  [<ffffffff81072cf0>] cancel_work_sync+0x10/0x20
[96833.124113]  [<ffffffffa065b5cd>] __ath_cancel_work+0x4d/0x60 [ath9k]
[96833.124119]  [<ffffffffa065cf28>] ath9k_config+0x458/0x680 [ath9k]
[96833.124125]  [<ffffffffa065dd1e>] ? ath9k_flush+0x6e/0x1d0 [ath9k]
[96833.124129]  [<ffffffff8144394d>] ? __mutex_unlock_slowpath+0x10d/0x190
[96833.124146]  [<ffffffffa056c7b5>] ieee80211_hw_config+0x135/0x2a0 [mac80211]
[96833.124163]  [<ffffffffa057ebbb>] ieee80211_do_open+0x67b/0xc50 [mac80211]
[96833.124178]  [<ffffffffa057f1fd>] ieee80211_open+0x6d/0x80 [mac80211]
[96833.124183]  [<ffffffff8137a44f>] __dev_open+0x9f/0xf0
[96833.124187]  [<ffffffff8137a701>] __dev_change_flags+0xa1/0x180
[96833.124190]  [<ffffffff8137a898>] dev_change_flags+0x28/0x70
[96833.124195]  [<ffffffff813e1179>] devinet_ioctl+0x659/0x780
[96833.124199]  [<ffffffff8137aea0>] ? dev_ioctl+0x210/0x6d0
[96833.124203]  [<ffffffff813e1db5>] inet_ioctl+0x75/0x90
[96833.124208]  [<ffffffff8135e0e0>] sock_do_ioctl+0x30/0x70
[96833.124211]  [<ffffffff8135e3dd>] sock_ioctl+0x7d/0x2c0
[96833.124218]  [<ffffffff81193c39>] do_vfs_ioctl+0x99/0x580
[96833.124222]  [<ffffffff81447415>] ? sysret_check+0x22/0x5d
[96833.124226]  [<ffffffff811941b9>] sys_ioctl+0x99/0xa0
[96833.124230]  [<ffffffff814473e9>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: raise aggregation limit to 64k for HT IBSS

mac80211 adds stations in HT IBSS as soon as a frame comes by,
even if the HT capabilities are not known yet (they are often
received later, e.g. in beacons). So far, ampdu factor/density
are only calculated when the station is initially added.

This patch changes this to update ampdu factor/density settings
when starting a blockack session.

Using this patch, we had performance boosts from 60 to 150 MBit/s
between two 2x2 Atheros devices in 5 GHz HT IBSS mode.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192se: Fix double inclusion of header pci.h

The command "make includecheck" yields the following for the rtlwifi tree:

/home/finger/linux-2.6/drivers/net/wireless/rtlwifi/rtl8192se/sw.c: ../pci.h is included more than once.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix IRQ disabled warning

The PCI-based drivers can generate the following warning:

[ 9497.776350] ------------[ cut here ]------------
[ 9497.776366] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7a/0xa0()
[ 9497.776370] Hardware name: 05794NC
[ 9497.776597] Pid: 6413, comm: hostapd Not tainted 3.3.0-4.fc16.x86_64 #1
[ 9497.776601] Call Trace:
[ 9497.776612]  [<ffffffff81057b1f>] warn_slowpath_common+0x7f/0xc0
[ 9497.776633]  [<ffffffffa034a099>] ? rtl_pci_reset_trx_ring+0x199/0x230
[rtlwifi]
[ 9497.776640]  [<ffffffff81057b7a>] warn_slowpath_null+0x1a/0x20
[ 9497.776646]  [<ffffffff8105f06a>] local_bh_enable_ip+0x7a/0xa0
[ 9497.776654]  [<ffffffff815f3ef6>] _raw_spin_unlock_bh+0x16/0x20
[ 9497.776671]  [<ffffffffa03e50de>] destroy_conntrack+0x9e/0x120
[nf_conntrack]
[ 9497.776681]  [<ffffffff81511847>] nf_conntrack_destroy+0x17/0x20
[ 9497.776689]  [<ffffffff814d9c85>] skb_release_head_state+0xe5/0x120
[ 9497.776695]  [<ffffffff814d98b6>] __kfree_skb+0x16/0xa0
[ 9497.776700]  [<ffffffff814d9a35>] kfree_skb+0x45/0xc0
[ 9497.776717]  [<ffffffffa034a099>] rtl_pci_reset_trx_ring+0x199/0x230
[rtlwifi]
[ 9497.776734]  [<ffffffffa034a155>] rtl_pci_start+0x25/0x1d0 [rtlwifi]
[ 9497.776750]  [<ffffffffa03440b5>] rtl_op_start+0x55/0x90 [rtlwifi]
[ 9497.776785]  [<ffffffffa02c4956>] ieee80211_do_open+0x296/0xa10 [mac80211]
[ 9497.776794]  [<ffffffff815f7ddd>] ? notifier_call_chain+0x4d/0x70
[ 9497.776828]  [<ffffffffa02c513d>] ieee80211_open+0x6d/0x80 [mac80211]
[ 9497.776836]  [<ffffffff814e8b3f>] __dev_open+0x8f/0xe0
[ 9497.776842]  [<ffffffff814e8de1>] __dev_change_flags+0xa1/0x180
[ 9497.776847]  [<ffffffff814e8f78>] dev_change_flags+0x28/0x70
[ 9497.776856]  [<ffffffff8154e99d>] devinet_ioctl+0x61d/0x7b0
[ 9497.776863]  [<ffffffff8154ef55>] inet_ioctl+0x75/0x90
[ 9497.776870]  [<ffffffff814cdd50>] sock_do_ioctl+0x30/0x70
[ 9497.776876]  [<ffffffff814cee09>] sock_ioctl+0x79/0x2f0
[ 9497.776885]  [<ffffffff81193498>] do_vfs_ioctl+0x98/0x550
[ 9497.776891]  [<ffffffff811939e1>] sys_ioctl+0x91/0xa0
[ 9497.776897]  [<ffffffff815fc029>] system_call_fastpath+0x16/0x1b
[ 9497.776902] ---[ end trace 22886c442489082d ]---

The cause is due to calling kfree_skb() with interrupts disabled.

This bug is discussed in https://bugzilla.redhat.com/show_bug.cgi?id=797709.

Reported-and-Tested by: Ivan Ivanovich <iivanich@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next

wlcore: print stack trace in every recovery

As recovery queuing can now occur from multiple code paths
it's convenient to know what triggered it in all cases
other than an intended recovery which is part of the
switch between single role to multi role.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: queue recovery in case of bus errors during cmd_remove_peer

Following the addition of propagating errors from the bus ops
there's a need to distinguish between bus errors (including timeout)
and a legitimate timeout occuring in cmd_wait_for_event_or_timeout.
In case of real bus errors we need to queue recovery even in cases
where a timeout on a response from the FW to a command is acceptable.

Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: fix broken TX due to wrong queuing of recovery

commit 14bba17b "wl12xx: Propagate errors from wl1271_raw_write32"
breaks down TX in certain scenarios. wl1271_irq_locked() propagates
errors from wl1271_tx_work_locked however it may return -EBUSY
when the FW queues are full which is a legitimate case and not a
a real error. In this case a recovery is triggered by wl1271_irq
and this keeps repeating itself so TX is completely broken.
Fix it by avoiding propagating return values as errors even if they
aren't. Only bus (SDIO or SPI) ops failures would be progagated
as only these should trigger recovery.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: fix some failure cases in wlcore_probe()

We need to release the IRQ if hw_info() or identify_chip() fails.  And
we need unregister the HW with mac80211 if there are any failures
after it's registered.

Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: deprecate PG1 support

The new PG2 version of the chip has a few differences in terms of FW
API if compared to PG1.  PG1 is just a sample that shouldn't be used
in real life, so to avoid having to handle both separately, mark the
PG1 version as deprecated and bail out during probe.

Signed-off-by: Luciano Coelho <coelho@ti.com>

mac80211: make __ieee80211_recalc_idle static

Since it's not called from any file outside where
it's defined, the function can be static if moved
up in the file before the callers.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: make ieee80211_check_concurrent_iface netdev-independent

ieee80211_check_concurrent_iface() need not use the
netdev. Remove the use of the netdev here to prepare
the function for P2P device addition.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove unused function

Remove the unused function is_ieee80211_device().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: specify RSSI threshold in scheduled scan

Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.

Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: fix smatch/sparse complaints

The code is fine in both cases as-is, but we can
write it slightly differently to fix smatch/sparse
complaints:
 * compare the skb pointer (which we use as a cookie)
   by casting the skb to unsigned long rather than the
   cookie to a pointer (fixes "different address spaces")
 * when transmitting, data->channel must be assigned,
   don't check it (fixes "dereferenced before check")

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: trace debug messages

It can be very useful to have all debug messages
available when debugging, but hard to correlate
between different sources, so add a trace event
for all mac80211 debug messages.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: rename driver-trace file

This file will contain more soon, so
rename it to just trace.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: clean up debugging

There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
 * a lot of messages should be pr_info, not pr_debug
 * wholesale use of pr_debug makes it require *both*
   Kconfig and dynamic configuration
 * there are still a lot of ifdefs
 * the style is very inconsistent, sometimes the
   sdata->name is printed in front

Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wlcore: prevent recovery in the middle of resume

Take the mutex early in the resume handler and use the locked version of
the IRQ routine. This ensures any recoveries queued will only take place
after resume has fully completed.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: refactor threaded IRQ routine

Separate the threaded IRQ handling routine into two functions.
The outer function takes the mutex and calls recovery on errors. It also
performs a Tx-path optimization to avoid redundant works.

The inner function is simplified - all calls to recovery are removed and
it assumes the lock is taken. The locked variant will be reused elsewhere.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: check Rx-filter functions in the suspend path

Propagate some missing return values for Rx-filter related functions.
This and makes sure we always fail the suspend in case of SDIO errors.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: force recovery on resume if suspended without recovering

If an error is detected after mac80211 is already suspended, the recovery
work will not be queued. This will leave the driver in a bad state on
resume.

Detect this in the resume op and re-queue a recovery.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: don't allow SDIO read/writes after failure

Set a flag and after the first read/write failure is encountered.
This flag will disallow further SDIO read/writes until op_stop() is
executed, which will clear all flags.

This prevents further errors from occurring, since one error usually
indicates that IO operations won't work anymore until the chip is
rebooted.  By blocking more calls, we avoid extra timeouts and having
to wait for them to occur.

[Added second paragraph explaining why the change is needed. -- Luca]

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: cancel suspend when recovery is pending

We wish to postpone suspend if recovery is pending. This will make sure
the FW is in a good state and perform wowlan wakeup.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: access the firmware memory via debugfs

Applications running in the user space needs access to the
memory of the chip. Examples of such access
- read/write global variables
- access to firmware log
- dump memory after firmware panic event

Arbitrary 4-bytes aligned location can be accessed by
read/write file wlcore/mem

[Check return value of wlcore_raw_read/write and wlcore_set_partition
calls as required by the recent IO changes. -- Luca]

Signed-off-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

rtlwifi: Change debug level for deletion of an entry in CAM

When running in AP mode, the driver reports all deletions from CAM in
a cryptic manner that makes users think it is an error. change so that
the condition is only reported at higher-levels of debugging.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix smatch warning in ar9003_hw_spur_mitigate_mrc_cck

drivers/net/wireless/ath/ath9k/ar9003_phy.c:211
ar9003_hw_spur_mitigate_mrc_cck() error: potential NULL dereference
'spur_fbin_ptr'.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: rename mrcCCKOff to fix smatch warning

Rename mrcCCKOff for better code readability and also fixes
the smatch warning.

drivers/net/wireless/ath/ath9k/ar9003_phy.c:982
ar9003_hw_ani_control() Error invalid range 1 to 0.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: fix NULL pointer crash in brcms_c_regd_init()

In the function brcms_c_regd_init() the channels are validated
against the device capabilities. This is done for both 2.4G and
5G band, but there are devices that are 2.4G only, ie. BCM4313.
For that device this leads to a NULL dereference. This patch adds
a check in brcms_c_regd_init() to fix this.

Issue introduced in wireless-next tree by following commit:
cf03c5d brcm80211: smac: inform mac80211 of the X2 regulatory domain

Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: make inclusion of vmalloc.h explicit fixing linux-next build

This patch fixes problem detected in linux-next build for powerpc
allyesconfig. The error message below is no longer observed:

  CC      drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c: In function 'brcmf_sdio_dump_console':
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: error: implicit declaration of function 'vzalloc'
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: warning: assignment makes pointer from integer without a cast
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3113: error: implicit declaration of function 'vfree'
make[2]: *** [drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o] Error 1

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: enhance power save for USB and PCIe chipsets

FW will not explicitly notify about host sleep activation to the
host for USB and PCIe chipsets. Hence host should generate Host
Sleep Activated event as soon as Host Sleep parameters are
configured to FW successfully.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: wake up main thread to handle Tx traffic if scan is delayed/aborted

This is a flaw in recently implemented logic to handle Tx traffic
and scan operation simultaneously. We missed to wakeup main thread
to handle Tx traffic if scan is delayed/aborted.

For some cards (SD8797, for example), firmware will send SLEEP event
if there is no activity for 50msec. While handling the SLEEP event,
main thread will be woken up and Tx packet gets sent hence. In worst
case Tx traffic will be delayed for 50msec.

For other cards, such as USB8797, firmware won't send SLEEP event.
So, Tx traffic gets stuck if no other event triggers the wakeup of
main thread.

This patch fixes above issues.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: parse WPA IE and support WPA/WPA2 mixed mode for uAP

Add support for parsing WPA IE from beacon parameter of
cfg80211_ap_settings and set it to FW.

WPA/WPA2 mixed mode is supported with this patch.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx

Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Merge branch 'for-john' of git://git.sipsolutions.net/mac80211-next

mac80211: pass sdata to some RX functions

For better debugging, we would like to have
the sdata pointer available later, so pass
it into these functions.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: two small verbose debug cleanups

Two instances of CONFIG_MAC80211_VERBOSE_DEBUG
should be different, fix them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: remove TKIP debug

The TKIP code hasn't been changed in a very long
time, so it seems unlikely that anyone really has
a need for the TKIP debug code. Remove it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wlcore: Force checking of io functions' return values

All io functions' return values should be propagated and handled. Add a
__must_check annotation to verify that the return values are checked and
to avoid future mistakes.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_read_hwaddr

Propagate errors from wl1271_read_hwaddr. This function is only used
when reading the FW log (following a recovery), so don't read the FW log
in case of a bus error.

Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_raw_write32

Propagate errors from wl1271_raw_write32 and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_raw_read32

Propagate errors from wl1271_raw_read32. Since the read functions had no
way of returning errors in-band, change their prototypes.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_write

Propagate errors from wl1271_write and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wl1271_read

Propagate errors from wl1271_read and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Propagate errors from wlcore_raw_*_data functions

wlcore_raw_read_data is called when the FW status is read which happens
while handling interrupts and when the FW log is read following a
recovery. Request a recovery in the former case, and don't read the FW
log in case the FW status read failed.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Change raw io functions to return errors

Make wl1271_raw_write and wl1271_raw_read return errors so the driver
could handle these appropriately.
Since the prototype has changed, also rename the prefix of these
functions to wlcore.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Change read/write ops to return errors

While bus operations may fail, either due to HW or FW issues, these are
never propagated to higher layers. As a result, the core driver has no
way of knowing that the operations failed, and will only recover if high
level logic requires it (e.g. no command completion).

Change read/write bus operations to return errors to let higher layer
functionality handle these.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Disable interrupts while recovering

In case a recovery is initiated, the FW can no longer be trusted, and
the driver should not handle any new FW events.

Disable the interrupt handler when a recovery is scheduled and balance
it back in the op_stop callback.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: Fix sdio out-of-sync power state

wl12xx_sdio_power_off() manually powers down the card regardless of the
runtime pm state. If wl12xx_sdio_power_on() is called before the card
was suspended by runtime PM, it will not power up the card.

As part of the HW detection, the chip's power is toggled. Since this
happens in the context of probing sdio, the power reference counter will
be higher than zero. As a result, when wl12xx_sdio_power_off() is
called, the chip will be powered down while still having a positive
power reference counter. If the interface is quickly activated, the
driver might try to transfer data to a powered off chip.

Fix this by ensuring that wl12xx_sdio_power_on() explicitly powers on
the chip in case runtime pm claims the chip is already powered on. To
avoid cases in which it is not possible to determine if the chip was
really powered on (card's power reference counter is positive), operate
on the mmc_card instead of the function.

Also verify that the chip is indeed powered on before powering off, to
avoid wrong reference counter values in error cases.

Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

ieee80211: more OUI type definitions for WLAN_OUI_MICROSOFT

WMM and WPS

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: add command to get current rssi

Get current rssi (in dBm) from the driver/FW.

Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.

Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge branch 'wl12xx-next' into for-linville

Conflicts:
drivers/net/wireless/ti/wl18xx/main.c

wl18xx: use %zu for size_t arguments in printk calls

After 934b9d1e (wl18xx: avoid some -Wformat warnings) there was still
a warning with (at least) ARM gcc version 4.4.1:

drivers/net/wireless/ti/wl18xx/main.c: In function 'wl18xx_conf_init':
drivers/net/wireless/ti/wl18xx/main.c:1026: warning: format '%ld' expects type 'long int', but argument 2 has type 'unsigned int'

Fix this by using %zu for the both formats, since the fw->size and the
macro (derived from sizeof()) are size_t.

Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: split siso40 HT cap between 2Ghz and 5Ghz

Remove the cap IEEE80211_HT_CAP_DSSSCCK40 from the 5Ghz variant of
the siso40 HT capabilities. It is meaningless in 5Ghz.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: sane defaults for HT capabilities

Introduce a default set of HT capabilities that are set according to the
number of antennas on the board. Move the HT setting code down to allow
the number of antennas to be set (and optionally overridden) before it.

Remove the "mimo" HT option, since the default mode now enables MIMO is
possible.

Use this opportunity to add a helper function for setting HT
capabilities and reduce the volume of the code a bit.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: explicitly remove the 5Ghz MIMO HT cap

The 18xx chip does not support MIMO in 5Ghz. Use the siso20 HT cap as
fallback in 5Ghz when "mimo" is requested.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: read FW logs from FW memory on watchdog recovery

FW uses a few memory blocks as a buffer to accumulate FW logs before
transmitting them to the host over SDIO. When FW WatchDog recovery
occurs, the last FW traces are still pending in the buffer. Driver is
to read these FW traces whether log mode is continuous or on demand.

FW memory blocks allocated for the log buffer are handled as a link list:
the first 4 bytes in each memory block contain FW address to the next block.
The end of list condition depends on FW log mode:
- on demand: the list is cyclic, the next address is equal to the first address
- continuous: the address is  equal to 0x2000000

Log data resides inside FW memory block with offset depending on
logger mode:
- on demand:  4 bytes (address of the next memory block)
- continuous: 4 bytes and Rx Descriptor structure size

Described FW logger API is backward compatible with previous FW versions.

Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wlcore: do not report noise level in get survey op

The get survey op expects the low level driver to report
the noise level for a a given channel.

The noise calculated in wlcore is (rssi-snr/2), but since
the snr reported by the FW is a derivative from the rssi
this calculation is useless, and should not be reported
to the user space.

Reporting incorrect noise, results in the wpa_supplicant
miscalculating the roaming candidate priority, thus causing
a situation where an AP with a lower rssi level would be
chosen over a better AP.

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: set Tx align quirk for PG2

Before patch b5d6d9b (wlcore/wl12xx/wl18xx: don't use TX align quirk
for wl127x), this was automatically set for all platforms. As this
should now be set explicitly, set it for PG2 as well.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl18xx: increase Rx descriptors for PG2

New PG2 firmwares have additional Rx descriptors.

Add a module parameter to manually set the number of Rx descriptors for
older versions (PG1). We cannot discriminate based on chip-id, since
this value must be set on probe.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>