Alexander Duyck [Wed, 13 Jan 2016 15:31:17 +0000 (07:31 -0800)]
ixgbevf: Add support for generic Tx checksums
This patch adds support for generic Tx checksums to the ixgbevf driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers. In
the case of the VF drivers this meant adding support for SCTP CRCs, and
inner checksum offloads for MPLS and various tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Wed, 13 Jan 2016 15:31:11 +0000 (07:31 -0800)]
ixgbe: Add support for generic Tx checksums
This patch adds support for generic Tx checksums to the ixgbe driver. It
turns out this is actually pretty easy after going over the datasheet as we
were doing a number of steps we didn't need to.
In order to perform a Tx checksum for an L4 header we need to fill in the
following fields in the Tx descriptor:
MACLEN (maximum of 127), retrieved from:
skb_network_offset()
IPLEN (maximum of 511), retrieved from:
skb_checksum_start_offset() - skb_network_offset()
TUCMD.L4T indicates offset and if checksum or crc32c, based on:
skb->csum_offset
The added advantage to doing this is that we can support inner checksum
offloads for tunnels and MPLS while still being able to transparently
insert VLAN tags.
I also took the opportunity to clean-up many of the feature flag
configuration bits to make them a bit more consistent between drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sowmini Varadhan [Wed, 13 Jan 2016 03:32:30 +0000 (19:32 -0800)]
ixgbe: use eth_platform_get_mac_address()
This commit converts commit
c762dff24c06 ("ixgbe: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit
c7f5d105495a ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Thu, 7 Jan 2016 18:13:03 +0000 (10:13 -0800)]
ixgbe: Make all unchanging ops structures const
The source for the ops structure contents are const, so make them
so. Copy them in place with structure assignments instead of memcpys.
Make the mbx_ops accessed by reference instead of making a copy of
the source structure. Update copyright date on the touched files.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 7 Jan 2016 06:48:50 +0000 (22:48 -0800)]
ixgbe: Avoid adding VLAN 0 twice to VLVF and VFTA
We were adding VLAN 0 twice each time we restored the VLAN configuration.
Instead of doing it twice we can just start working through the active
VLANs from ID 1 on and skip the double write.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 7 Jan 2016 06:48:44 +0000 (22:48 -0800)]
ixgbe: Do not allow PF to add VLVF entry unless it actually needs it
While doing the work on igb I realized there were a few cases where we were
still adding VLANs to the VLVF entries for the PF when they were not
needed. This patch cleans that up so that the only time we add a PF entry
to the VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
chas williams [Tue, 5 Jan 2016 22:30:39 +0000 (17:30 -0500)]
ixgbe: Extend trust to allow guest to set unicast address
When running certain routing protocols like VRRP, VF guests need the
ability to set the unicast address of the interface. Extend the new ndo
trust feature to let the hypervisor trust a guest to set/update its own
unicast address.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Fri, 18 Dec 2015 01:32:55 +0000 (17:32 -0800)]
ixgbevf: use bit operations for setting and checking resets
Move the reset flags to adapter->state in order to make use of bit
operations.
This is an alternative patch to the one previously submitted by
John Greene.
Suggested-by: Alexander Duyck <aduyck@mirantis.com>
Reported-by: Scott Otto <otts62@yahoo.com>
Reported-by: John Greene <jogreene@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pavel Tikhomirov [Fri, 11 Dec 2015 14:05:14 +0000 (17:05 +0300)]
ixgbe: on recv increment rx.ring->stats.yields
It seem to be non intentionally changed to Tx in
commit
adc810900a70 ("ixgbe: Refactor busy poll socket code to address
multiple issues")
Lock is taken from ixgbe_low_latency_recv, and there under this
lock we use ixgbe_clean_rx_irq so it looks wrong for me to increment
Tx counter.
Yield stats can be shown through ethtool:
ethtool -S enp129s0 | grep yield
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Sun, 3 Apr 2016 00:23:10 +0000 (20:23 -0400)]
Merge branch 'stmmac-GMAC4.x'
Alexandre TORGUE says:
====================
Enhance stmmac driver to support GMAC4.x IP
This is a subset of patch to enhance current stmmac driver to support
new GMAC4.x chips. New set of callbacks is defined to support this new
family: descriptors, dma, core.
One of main changes of GMAC 4.xx IP is descriptors management.
-descriptors are only used in ring mode.
-A descriptor is composed of 4 32bits registers (no more extended
descriptors)
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
New features are available on IP:
-TSO (TCP Segmentation Offload) for TX only
-Split header: to have header and payload in 2 different buffers (not yet implemented)
Below some throughput figures obtained on some boxes:
iperf (mbps)
--------------------------------------
tcp udp
tx rx tx rx
-----------------
GMAC4.x 935 930 750 800
Note: There is a change in 4.10a databook on bitfield mapping of DMA_CHANx_INTR_ENA register.
This requires to have é diffrent set of callbacks between IP 4.00a and 4.10a.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:37 +0000 (11:37 +0200)]
stmmac: update MAINTAINERS
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:36 +0000 (11:37 +0200)]
stmmac: update version to Jan_2016
This patch just updates the driver to the version fully
tested on STi platforms. This version is Jan_2016.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:35 +0000 (11:37 +0200)]
Documentation: networking: update stmmac
Update stmmac driver documentation according to new GMAC 4.x family.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:34 +0000 (11:37 +0200)]
stmmac: support new GMAC4
This patch adds the whole GMAC4 support inside the
stmmac d.d. now able to use the new HW and some new features
i.e.: TSO.
It is missing the multi-queue and split Header support at this
stage.
This patch also updates the driver version and the stmmac.txt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:33 +0000 (11:37 +0200)]
stmmac: add new DT platform entries for GMAC4
This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:32 +0000 (11:37 +0200)]
stmmac: enhance mmc counter management
For gmac3, the MMC addr map is: 0x100 - 0x2fc
For gmac4, the MMC addr map is: 0x700 - 0x8fc
So instead of adding 0x600 to the IO address when setup the mmc,
the RMON base address is saved inside the private structure and
then used to manage the counters.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:31 +0000 (11:37 +0200)]
stmmac: add GMAC4 core support
This is the initial support for GMAC4 that includes
the main callbacks to setup the core module: including
Csum, basic filtering, mac address and interrupt (MMC,
MTL, PMT) No LPI added.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:30 +0000 (11:37 +0200)]
stmmac: add DMA support for GMAC 4.xx
DMA behavior is linked to descriptor management:
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last
descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
Up to 8 DMA could be use but currently we only use one (channel0)
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:29 +0000 (11:37 +0200)]
stmmac: add GMAC4 DMA/CORE Header File
This is the main header file to define all the
macro used for GMAC4 DMA and CORE parts.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:28 +0000 (11:37 +0200)]
stmmac: add descriptors function for GMAC 4.xx
One of main changes of GMAC 4.xx IP is descriptors management.
-descriptors are only used in ring mode.
-A descriptor is composed of 4 32bits registers (no more extended
descriptors)
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor
ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
-DMA_CH#_TxDesc_Tail_Pointer: address of the last
descriptor to send + 1.
-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
descriptor
-The descriptor Tail Pointer register contains the pointer to the
descriptor address (N). The base address and the current
descriptor decide the address of the current descriptor that the
DMA can process. The descriptors up to one location less than the
one indicated by the descriptor tail pointer (N-1) are owned by
the DMA. The DMA continues to process the descriptors until the
following condition occurs:
"current descriptor pointer == Descriptor Tail pointer"
Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new
transfer:
"current descriptor pointer < Descriptor tail pointer"
The DMA automatically wraps around the base address when the end
of ring is reached.
-New features are available on IP:
-TSO (TCP Segmentation Offload) for TX only
-Split header: to have header and payload in 2 different buffers
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:27 +0000 (11:37 +0200)]
stmmac: rework synopsys id read, moved to dwmac setup
synopsys_uid is only used once after setup, to get synopsys_id
by using shitf/mask operation. It's no longer used then.
So, remove this temporary variable and directly compute
synopsys_id from setup routine.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:26 +0000 (11:37 +0200)]
stmmac: rework the routines to show the ring status
To avoid lot of check in stmmac_main for display ring management
and support the GMAC4 chip, the display_ring function is moved
into dedicated descriptor file.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre TORGUE [Fri, 1 Apr 2016 09:37:25 +0000 (11:37 +0200)]
stmmac: rework get_hw_feature function
On next GMAC IP generation (4.xx), the way to get hw feature
is not the same than on previous 3.xx. As it is hardware
dependent, the way to get hw capabilities should be defined in dma ops of
each MAC IP. It will avoid also a huge computation of hw capabilities in
stmmac_main.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lisheng [Thu, 31 Mar 2016 13:00:09 +0000 (21:00 +0800)]
net: hns: add support of pause frame ctrl for HNS V2
The patch adds support of pause ctrl for HNS V2, and this feature is lost
by HNS V1:
1) service ports can disable rx pause frame,
2) debug ports can open tx/rx pause frame.
And this patch updates the REGs about the pause ctrl when updated
status function called by upper layer routine.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Thu, 31 Mar 2016 10:21:38 +0000 (18:21 +0800)]
netlink: use nla_get_in_addr and nla_put_in_addr for ipv4 address
Since nla_get_in_addr and nla_put_in_addr were implemented,
so use them appropriately.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Wed, 30 Mar 2016 21:54:20 +0000 (14:54 -0700)]
tcp: remove cwnd moderation after recovery
For non-SACK connections, cwnd is lowered to inflight plus 3 packets
when the recovery ends. This is an optional feature in the NewReno
RFC 2582 to reduce the potential burst when cwnd is "re-opened"
after recovery and inflight is low.
This feature is questionably effective because of PRR: when
the recovery ends (i.e., snd_una == high_seq) NewReno holds the
CA_Recovery state for another round trip to prevent false fast
retransmits. But if the inflight is low, PRR will overwrite the
moderated cwnd in tcp_cwnd_reduction() later regardlessly. So if a
receiver responds bogus ACKs (i.e., acking future data) to speed up
transfer after recovery, it can only induce a burst up to a window
worth of data packets by acking up to SND.NXT. A restart from (short)
idle or receiving streched ACKs can both cause such bursts as well.
On the other hand, if the recovery ends because the sender
detects the losses were spurious (e.g., reordering). This feature
unconditionally lowers a reverted cwnd even though nothing
was lost.
By principle loss recovery module should not update cwnd. Further
pacing is much more effective to reduce burst. Hence this patch
removes the cwnd moderation feature.
v2 changes: revised commit message on bogus ACKs and burst, and
missing signature
Signed-off-by: Matt Mathis <mattmathis@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 2 Apr 2016 01:03:33 +0000 (20:03 -0500)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Missing device reference in IPSEC input path results in crashes
during device unregistration. From Subash Abhinov Kasiviswanathan.
2) Per-queue ISR register writes not being done properly in macb
driver, from Cyrille Pitchen.
3) Stats accounting bugs in bcmgenet, from Patri Gynther.
4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
Quentin Armitage.
5) SXGBE driver has off-by-one in probe error paths, from Rasmus
Villemoes.
6) Fix race in save/swap/delete options in netfilter ipset, from
Vishwanath Pai.
7) Ageing time of bridge not set properly when not operating over a
switchdev device. Fix from Haishuang Yan.
8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
Duyck.
9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.
10) FEC driver should only access registers that actually exist on the
given chipset, fix from Fabio Estevam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
net: mvneta: fix changing MTU when using per-cpu processing
stmmac: fix MDIO settings
Revert "stmmac: Fix 'eth0: No PHY found' regression"
stmmac: fix TX normal DESC
net: mvneta: use cache_line_size() to get cacheline size
net: mvpp2: use cache_line_size() to get cacheline size
net: mvpp2: fix maybe-uninitialized warning
tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
rtnl: fix msg size calculation in if_nlmsg_size()
fec: Do not access unexisting register in Coldfire
net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
bpf: make padding in bpf_tunnel_key explicit
ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
bnxt_en: Fix ethtool -a reporting.
bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
bnxt_en: Implement proper firmware message padding.
...
Linus Torvalds [Sat, 2 Apr 2016 00:57:13 +0000 (19:57 -0500)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of const updates for reset ops and a couple fixes to the
newly introduced IPQ4019 clock driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: ipq4019: add some fixed clocks for ddrppl and fepll
clk: qcom: ipq4019: switch remaining defines to enums
clk: qcom: Make reset_control_ops const
clk: tegra: Make reset_control_ops const
clk: sunxi: Make reset_control_ops const
clk: atlas7: Make reset_control_ops const
clk: rockchip: Make reset_control_ops const
clk: mmp: Make reset_control_ops const
clk: mediatek: Make reset_control_ops const
Linus Torvalds [Sat, 2 Apr 2016 00:52:10 +0000 (19:52 -0500)]
Merge tag 'pm+acpi-4.6-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fix from Rafael J. Wysocki:
"Just one fix for a nasty boot failure on some systems based on Intel
Skylake that shipped with broken firmware where enabling
hardware-coordinated P-states management (HWP) causes a faulty
interrupt handler in SMM to be invoked and crash the system (Srinivas
Pandruvada)"
* tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / processor: Request native thermal interrupt handling via _OSC
Linus Torvalds [Sat, 2 Apr 2016 00:31:19 +0000 (19:31 -0500)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"11 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
Rafael J. Wysocki [Fri, 1 Apr 2016 23:17:36 +0000 (01:17 +0200)]
Merge branch 'acpi-processor'
* acpi-processor:
ACPI / processor: Request native thermal interrupt handling via _OSC
Linus Torvalds [Fri, 1 Apr 2016 23:08:34 +0000 (18:08 -0500)]
Merge branch 'for-linus-4.6' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has a few fixes Dave Sterba had queued up. These are all pretty
small, but since they were tested I decided against waiting for more"
* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: transaction_kthread() is not freezable
btrfs: cleaner_kthread() doesn't need explicit freeze
btrfs: do not write corrupted metadata blocks to disk
btrfs: csum_tree_block: return proper errno value
Linus Torvalds [Fri, 1 Apr 2016 22:17:32 +0000 (17:17 -0500)]
Merge tag 'for-linus' of git://github.com/martinbrandenburg/linux
Pull OrangeFS fixes from Martin Brandenburg:
"Two bugfixes for OrangeFS.
One is a reference counting bug and the other is a typo in client
minimum version"
* tag 'for-linus' of git://github.com/martinbrandenburg/linux:
orangefs: minimum userspace version is 2.9.3
orangefs: don't put readdir slot twice
Linus Torvalds [Fri, 1 Apr 2016 22:15:51 +0000 (17:15 -0500)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix oops when patching in alternative sequences on big-endian CPUs
- reconcile asm/perf_event.h after merge window fallout with KVM ARM
- defconfig updates
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: updates for 4.6
arm64: perf: Move PMU register related defines to asm/perf_event.h
arm64: opcodes.h: Add arm big-endian config options before including arm header
Linus Torvalds [Fri, 1 Apr 2016 22:13:23 +0000 (17:13 -0500)]
Merge tag 'sound-4.6-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- a fix in ALSA timer core to avoid possible BUG() trigger
- a fix in ALSA timer core 32bit compat layer
- a few HD-audio quirks for ASUS and HP machines
- AMD HD-audio HDMI controller quirks
- fixes of USB-audio double-free at some error paths
- a fix for memory leak in DICE driver at hotunplug"
* tag 'sound-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: timer: Use mod_timer() for rearming the system timer
ALSA: hda - fix front mic problem for a HP desktop
ALSA: usb-audio: Fix double-free in error paths after snd_usb_add_audio_stream() call
ALSA: hda: add AMD Polaris-10/11 AZ PCI IDs with proper driver caps
ALSA: dice: fix memory leak when unplugging
ALSA: hda - Apply fix for white noise on Asus N550JV, too
ALSA: hda - Fix white noise on Asus N750JV headphone
ALSA: hda - Asus N750JV external subwoofer fixup
ALSA: timer: fix gparams ioctl compatibility for different architectures
Christophe Ricard [Fri, 1 Apr 2016 21:31:42 +0000 (14:31 -0700)]
.mailmap: add Christophe Ricard
Different computers had different settings in the mail client. Some
contributions appear as Christophe Ricard, others as Christophe RICARD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andi Kleen [Fri, 1 Apr 2016 21:31:40 +0000 (14:31 -0700)]
Make CONFIG_FHANDLE default y
Newer Fedora and OpenSUSE didn't boot with my standard configuration.
It took me some time to figure out why, in fact I had to write a script
to try different config options systematically.
The problem is that something (systemd) in dracut depends on
CONFIG_FHANDLE, which adds open by file handle syscalls.
While it is set in defconfigs it is very easy to miss when updating
older configs because it is not default y.
Make it default y and also depend on EXPERT, as dracut use is likely
widespread.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Zhang [Fri, 1 Apr 2016 21:31:37 +0000 (14:31 -0700)]
mm/page_isolation.c: fix the function comments
Commit
fea85cff11de ("mm/page_isolation.c: return last tested pfn rather
than failure indicator") changed the meaning of the return value. Let's
change the function comments as well.
Signed-off-by: Neil Zhang <neilzhang1123@hotmail.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 1 Apr 2016 21:31:34 +0000 (14:31 -0700)]
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
Commit
bb29902a7515 ("oom, oom_reaper: protect oom_reaper_list using
simpler way") has simplified the check for tasks already enqueued for
the oom reaper by checking tsk->oom_reaper_list != NULL. This check is
not sufficient because the tsk might be the head of the queue without
any other tasks queued and then we would simply lockup looping on the
same task. Fix the condition by checking for the head as well.
Fixes:
bb29902a7515 ("oom, oom_reaper: protect oom_reaper_list using simpler way")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lucas Stach [Fri, 1 Apr 2016 21:31:32 +0000 (14:31 -0700)]
mm/page_isolation: fix tracepoint to mirror check function behavior
Page isolation has not failed if the fin pfn extends beyond the end pfn
and test_pages_isolated checks this correctly. Fix the tracepoint to
report the same result as the actual check function.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Fri, 1 Apr 2016 21:31:26 +0000 (14:31 -0700)]
mm/rmap: batched invalidations should use existing api
The recently introduced batched invalidations mechanism uses its own
mechanism for shootdown. However, it does wrong accounting of
interrupts (e.g., inc_irq_stat is called for local invalidations),
trace-points (e.g., TLB_REMOTE_SHOOTDOWN for local invalidations) and
may break some platforms as it bypasses the invalidation mechanisms of
Xen and SGI UV.
This patch reuses the existing TLB flushing mechnaisms instead. We use
NULL as mm to indicate a global invalidation is required.
Fixes
72b252aed506b8 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nadav Amit [Fri, 1 Apr 2016 21:31:23 +0000 (14:31 -0700)]
x86/mm: TLB_REMOTE_SEND_IPI should count pages
TLB_REMOTE_SEND_IPI was recently introduced, but it counts bytes instead
of pages. In addition, it does not report correctly the case in which
flush_tlb_page flushes a page. Fix it to be consistent with other TLB
counters.
Fixes:
5b74283ab251b9d ("x86, mm: trace when an IPI is about to be sent")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xishi Qiu [Fri, 1 Apr 2016 21:31:20 +0000 (14:31 -0700)]
mm: fix invalid node in alloc_migrate_target()
It is incorrect to use next_node to find a target node, it will return
MAX_NUMNODES or invalid node. This will lead to crash in buddy system
allocation.
Fixes:
c8721bbbdd36 ("mm: memory-hotplug: enable memory hotplug to handle hugepage")
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Laura Abbott" <lauraa@codeaurora.org>
Cc: Hui Zhu <zhuhui@xiaomi.com>
Cc: Wang Xiaoqiang <wangxq10@lzu.edu.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chen Gang [Fri, 1 Apr 2016 21:31:17 +0000 (14:31 -0700)]
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
The return value of pmd_trans_huge_lock() is a pointer, not a boolean
value, so use NULL instead of false as the return value.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Potapenko [Fri, 1 Apr 2016 21:31:15 +0000 (14:31 -0700)]
mm, kasan: fix compilation for CONFIG_SLAB
Add the missing argument to set_track().
Fixes:
cd11016e5f52 ("mm, kasan: stackdepot implementation. Enable stackdepot for SLAB")
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Konstantin Serebryany <kcc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Fri, 1 Apr 2016 21:31:12 +0000 (14:31 -0700)]
MAINTAINERS: orangefs mailing list is subscribers-only
So update MAINTAINERS to say so.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcin Wojtas [Fri, 1 Apr 2016 13:21:18 +0000 (15:21 +0200)]
net: mvneta: fix changing MTU when using per-cpu processing
After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.
This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Apr 2016 18:38:59 +0000 (14:38 -0400)]
Merge branch 'stmmac-fixes'
Giuseppe Cavallaro says:
====================
stmmac MDIO and normal descr fixes
This patch series is to fix the problems below and recently debugged
in this mailing list:
o to fix a problem for the HW where the normal descriptor
o to fix the mdio registration according to the different
platform configurations
I am resending all the patches again: built on top of net.git repo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Fri, 1 Apr 2016 07:07:16 +0000 (09:07 +0200)]
stmmac: fix MDIO settings
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Fri, 1 Apr 2016 07:07:15 +0000 (09:07 +0200)]
Revert "stmmac: Fix 'eth0: No PHY found' regression"
This reverts commit
88f8b1bb41c6208f81b6a480244533ded7b59493.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Fri, 1 Apr 2016 07:07:14 +0000 (09:07 +0200)]
stmmac: fix TX normal DESC
This patch fixs a regression raised when test on chips that use
the normal descriptor layout. In fact, no len bits were set for
the TDES1 and no OWN bit inside the TDES0.
Signed-off-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Fri, 1 Apr 2016 09:12:49 +0000 (17:12 +0800)]
net: mvneta: use cache_line_size() to get cacheline size
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Fri, 1 Apr 2016 09:11:05 +0000 (17:11 +0800)]
net: mvpp2: use cache_line_size() to get cacheline size
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Thu, 31 Mar 2016 09:01:23 +0000 (17:01 +0800)]
net: mvpp2: fix maybe-uninitialized warning
This is to fix the following maybe-uninitialized warning:
drivers/net/ethernet/marvell/mvpp2.c:6007:18: warning: 'err' may be
used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 31 Mar 2016 00:13:18 +0000 (02:13 +0200)]
tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
Sasha Levin reported a suspicious rcu_dereference_protected() warning
found while fuzzing with trinity that is similar to this one:
[ 52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage!
[ 52.765688] other info that might help us debug this:
[ 52.765695] rcu_scheduler_active = 1, debug_locks = 1
[ 52.765701] 1 lock held by a.out/1525:
[ 52.765704] #0: (rtnl_mutex){+.+.+.}, at: [<
ffffffff816a64b7>] rtnl_lock+0x17/0x20
[ 52.765721] stack backtrace:
[ 52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264
[...]
[ 52.765768] Call Trace:
[ 52.765775] [<
ffffffff813e488d>] dump_stack+0x85/0xc8
[ 52.765784] [<
ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110
[ 52.765792] [<
ffffffff816afdc2>] sk_detach_filter+0x82/0x90
[ 52.765801] [<
ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun]
[ 52.765810] [<
ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun]
[ 52.765818] [<
ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210
[ 52.765827] [<
ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun]
[ 52.765834] [<
ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690
[ 52.765843] [<
ffffffff81364af3>] ? security_file_ioctl+0x43/0x60
[ 52.765850] [<
ffffffff81261519>] SyS_ioctl+0x79/0x90
[ 52.765858] [<
ffffffff81003ba2>] do_syscall_64+0x62/0x140
[ 52.765866] [<
ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in
f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in
994051625981 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 1 Apr 2016 12:21:18 +0000 (07:21 -0500)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too crazy in here: a bunch of AMD fixes/quirks, two msm fixes,
some rockchip fixes, and a udl warning fix, along with one locking fix
for displayport that seems to fix some dodgy monitors"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/udl: Use unlocked gem unreferencing
drm/dp: move hw_mutex up the call stack
drm/amdgpu: Don't move pinned BOs
drm/radeon: Don't move pinned BOs
drm/radeon: add a dpm quirk for all R7 370 parts
drm/radeon: add another R7 370 quirk
drm/rockchip: dw_hdmi: Don't call platform_set_drvdata()
drm/rockchip: vop: Fix vop crtc cleanup
drm/rockchip: dw_hdmi: Call drm_encoder_cleanup() in error path
drm/rockchip: vop: Disable planes when disabling CRTC
drm/rockchip: vop: Don't reject empty modesets
drm/rockchip: cancel pending vblanks on close
drm/rockchip: vop: fix crtc size in plane check
drm/radeon: add a dpm quirk for sapphire Dual-X R7 370 2G D5
drm/amd: Beef up ACP Kconfig menu text
drm/msm: fix typo in the !COMMON_CLK case
drm/msm: fix bug after preclose removal
Linus Torvalds [Fri, 1 Apr 2016 12:18:27 +0000 (07:18 -0500)]
Merge tag 'powerpc-4.6-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fixup preempt underflow with huge pages from Sebastian Siewior
- Fix altivec SPR not being saved from Oliver O'Halloran
- Correct used_vsr comment from Simon Guo
* tag 'powerpc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Correct used_vsr comment
powerpc/process: Fix altivec SPR not being saved
powerpc/mm: Fixup preempt underflow with huge pages
Linus Torvalds [Fri, 1 Apr 2016 12:15:54 +0000 (07:15 -0500)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
- A proper fix for the locking issue in the dasd driver
- Wire up the new preadv2 nad pwritev2 system calls
- Add the mark_rodata_ro function and set DEBUG_RODATA=y
- A few more bug fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: wire up preadv2/pwritev2 syscalls
s390/pci: PCI function group 0 is valid for clp_query_pci_fn
s390/crypto: provide correct file mode at device register.
s390/mm: handle PTE-mapped tail pages in fast gup
s390: add DEBUG_RODATA support
s390: disable postinit-readonly for now
s390/dasd: reorder lcu and device lock
s390/cpum_sf: Fix cpu hotplug notifier transitions
s390/cpum_cf: Fix missing cpu hotplug notifier transition
Takashi Iwai [Fri, 1 Apr 2016 10:28:16 +0000 (12:28 +0200)]
ALSA: timer: Use mod_timer() for rearming the system timer
ALSA system timer backend stops the timer via del_timer() without sync
and leaves del_timer_sync() at the close instead. This is because of
the restriction by the design of ALSA timer: namely, the stop callback
may be called from the timer handler, and calling the sync shall lead
to a hangup. However, this also triggers a kernel BUG() when the
timer is rearmed immediately after stopping without sync:
kernel BUG at kernel/time/timer.c:966!
Call Trace:
<IRQ>
[<
ffffffff8239c94e>] snd_timer_s_start+0x13e/0x1a0
[<
ffffffff8239e1f4>] snd_timer_interrupt+0x504/0xec0
[<
ffffffff8122fca0>] ? debug_check_no_locks_freed+0x290/0x290
[<
ffffffff8239ec64>] snd_timer_s_function+0xb4/0x120
[<
ffffffff81296b72>] call_timer_fn+0x162/0x520
[<
ffffffff81296add>] ? call_timer_fn+0xcd/0x520
[<
ffffffff8239ebb0>] ? snd_timer_interrupt+0xec0/0xec0
....
It's the place where add_timer() checks the pending timer. It's clear
that this may happen after the immediate restart without sync in our
cases.
So, the workaround here is just to use mod_timer() instead of
add_timer(). This looks like a band-aid fix, but it's a right move,
as snd_timer_interrupt() takes care of the continuous rearm of timer.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Heiko Carstens [Mon, 21 Mar 2016 12:48:43 +0000 (13:48 +0100)]
s390: wire up preadv2/pwritev2 syscalls
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pierre Morel [Wed, 16 Mar 2016 12:56:35 +0000 (13:56 +0100)]
s390/pci: PCI function group 0 is valid for clp_query_pci_fn
The PCI function group 0 is a valid function group,
it is wrong to reject it.
Let's accept PCI function group 0.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hui Wang [Fri, 1 Apr 2016 03:00:15 +0000 (11:00 +0800)]
ALSA: hda - fix front mic problem for a HP desktop
The front mic jack (pink color) can't detect any plug or unplug. After
applying this fix, both detecting function and recording function
work well.
BugLink: https://bugs.launchpad.net/bugs/1564712
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Daniel Vetter [Wed, 30 Mar 2016 09:40:43 +0000 (11:40 +0200)]
drm/udl: Use unlocked gem unreferencing
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
commit
ef4c6270bf2867e2f8032e9614d1a8cfc6c71663
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 09:36:25 2015 +0200
drm/gem: Check locking in drm_gem_object_unreference
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rob Clark [Thu, 25 Feb 2016 21:15:05 +0000 (16:15 -0500)]
drm/dp: move hw_mutex up the call stack
1) don't let other threads trying to bang on aux channel interrupt the
defer timeout/logic
2) don't let other threads interrupt the i2c over aux logic
Technically, according to people who actually have the DP spec, this
should not be required. In practice, it makes some troublesome Dell
monitor (and perhaps others) work, so probably a case of "It's compliant
if it works with windows" on the hw vendor's part..
v2: rebased to come before DPCD/AUX logging patch for easier backport
to stable branches.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1274157
Cc: stable@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 1 Apr 2016 03:14:24 +0000 (13:14 +1000)]
Merge branch 'drm-rockchip-next-fixes-2016-03-28' of https://github.com/markyzq/kernel-drm-rockchip into drm-fixes
bunch of rockchip fixes.
* 'drm-rockchip-next-fixes-2016-03-28' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: dw_hdmi: Don't call platform_set_drvdata()
drm/rockchip: vop: Fix vop crtc cleanup
drm/rockchip: dw_hdmi: Call drm_encoder_cleanup() in error path
drm/rockchip: vop: Disable planes when disabling CRTC
drm/rockchip: vop: Don't reject empty modesets
drm/rockchip: cancel pending vblanks on close
drm/rockchip: vop: fix crtc size in plane check
Dave Airlie [Fri, 1 Apr 2016 03:14:10 +0000 (13:14 +1000)]
Merge branch 'msm-fixes-4.6-rc1' of git://people.freedesktop.org/~robclark/linux into drm-fixes
two minor msm fixes.
* 'msm-fixes-4.6-rc1' of git://people.freedesktop.org/~robclark/linux:
drm/msm: fix typo in the !COMMON_CLK case
drm/msm: fix bug after preclose removal
Dave Airlie [Fri, 1 Apr 2016 03:13:34 +0000 (13:13 +1000)]
Merge branch 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just a few fixes for 4.6 this week:
- Add some SI DPM quirks
- Improve the ACP Kconfig text
- Additional BO pinning checks
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Don't move pinned BOs
drm/radeon: Don't move pinned BOs
drm/radeon: add a dpm quirk for all R7 370 parts
drm/radeon: add another R7 370 quirk
drm/radeon: add a dpm quirk for sapphire Dual-X R7 370 2G D5
drm/amd: Beef up ACP Kconfig menu text
Daniele Palmas [Thu, 31 Mar 2016 13:16:47 +0000 (15:16 +0200)]
net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
Telit LE910 V2 is a mobile broadband card with no ARP capabilities:
the patch makes this device to use wwan_noarp_info struct
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 31 Mar 2016 16:10:31 +0000 (18:10 +0200)]
rtnl: fix msg size calculation in if_nlmsg_size()
Size of the attribute IFLA_PHYS_PORT_NAME was missing.
Fixes:
db24a9044ee1 ("net: add support for phys_port_name")
CC: David Ahern <dsahern@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Thu, 31 Mar 2016 15:05:17 +0000 (12:05 -0300)]
fec: Do not access unexisting register in Coldfire
Commit
55cd48c821de ("net: fec: stop the "rcv is not +last, " error
messages") introduces a write to a register that does not exist in
Coldfire.
Move the FEC_FTRL register access inside the FEC_QUIRK_HAS_RACC 'if' block,
so that we guarantee it will not be used on Coldfire CPUs.
Reported-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Wed, 30 Mar 2016 11:55:21 +0000 (19:55 +0800)]
net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
The mvneta is also used in some Marvell berlin family SoCs which may
have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE
usage with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Wed, 30 Mar 2016 11:53:41 +0000 (19:53 +0800)]
net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
The mvpp2 ip maybe used in SoCs which may have have 64bytes cacheline
size. Replace the MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Uiterwijk [Wed, 30 Mar 2016 01:39:41 +0000 (01:39 +0000)]
net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
Some of the vendor-specific bootloaders set up this part
of the initialization for us, so this was never added.
However, since upstream bootloaders don't initialize the
chip specifically, they leave the fiber MII's PDOWN flag
set, which means that the CPU port doesn't connect.
This patch checks whether this flag has been clear prior
by something else, and if not make us clear it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Uiterwijk [Wed, 30 Mar 2016 01:39:40 +0000 (01:39 +0000)]
net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
Add versions of the phy_page_read and _write functions to
be used in a context where the SMI mutex is held.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladis Dronov [Thu, 31 Mar 2016 16:05:43 +0000 (12:05 -0400)]
ALSA: usb-audio: Fix double-free in error paths after snd_usb_add_audio_stream() call
create_fixed_stream_quirk(), snd_usb_parse_audio_interface() and
create_uaxx_quirk() functions allocate the audioformat object by themselves
and free it upon error before returning. However, once the object is linked
to a stream, it's freed again in snd_usb_audio_pcm_free(), thus it'll be
double-freed, eventually resulting in a memory corruption.
This patch fixes these failures in the error paths by unlinking the audioformat
object before freeing it.
Based on a patch by Takashi Iwai <tiwai@suse.de>
[Note for stable backports:
this patch requires the commit
902eb7fd1e4a ('ALSA: usb-audio: Minor
code cleanup in create_fixed_stream_quirk()')]
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1283358
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Cc: <stable@vger.kernel.org> # see the note above
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Martin Brandenburg [Wed, 30 Mar 2016 20:18:43 +0000 (16:18 -0400)]
orangefs: minimum userspace version is 2.9.3
Version 2.9.4 isn't even released yet.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Martin Brandenburg [Mon, 28 Mar 2016 21:18:27 +0000 (17:18 -0400)]
orangefs: don't put readdir slot twice
This was quite an oversight. After a readdir, the module could not be
unloaded, the number of slots is wrong, and memory near the slot bitmap
is possibly corrupt. Oops.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
David S. Miller [Thu, 31 Mar 2016 15:40:16 +0000 (11:40 -0400)]
Merge branch '10GbE' of git://git./linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-03-29
This series contains fixes to ixgbe and ixgbevf.
Tushar fixes an issue which was introduced with an earlier commit, where
hardware register RAR0 default MAC address does not get set properly.
Alex fixes two issues, first being the VXLAN port number should be stored
in network order instead of in host order. The second fix corrects the ATR
code to handle IPv6 extension headers. The issue was ATR code was assuming
that it would be able to use tcp_hdr for every TCP frame that came through,
but that is not the case, which resulted in bad filters being setup.
Mark fixes a use of usleep_range() to udelay() in the case where a lock
is being held.
Stefan fixes the offline self tests where ndo_stop() should be used instead
of ndo_close(), which causes IFF_UP to be cleared and interface routes get
removed.
Emil fixes the error case where we need to return an error when a MAC
address change is rejected by the PF. This helps prevent the user from
modifying the MAC address when the operation is not permitted.
Sridhar provides three fixes for ixgbe, all dealing with traffic class
offload handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Maruthi Srinivas Bayyavarapu [Thu, 31 Mar 2016 12:40:03 +0000 (18:10 +0530)]
ALSA: hda: add AMD Polaris-10/11 AZ PCI IDs with proper driver caps
This commit fixes garbled audio on Polaris-10/11 variants
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Thu, 31 Mar 2016 12:55:14 +0000 (07:55 -0500)]
Merge branch 'parisc-4.6-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix seccomp filter support and SIGSYS signals on compat kernel.
Both patches are tagged for v4.5 stable kernel"
* 'parisc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix and enable seccomp filter support
parisc: Fix SIGSYS signals in compat case
Linus Torvalds [Thu, 31 Mar 2016 12:19:39 +0000 (07:19 -0500)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fix from Al Viro.
Automount handling was broken by commit
e3c13928086f ("namei: massage
lookup_slow() to be usable by lookup_one_len_unlocked()") moving the
test for negative dentry too early.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the braino in "namei: massage lookup_slow() to be usable by lookup_one_len_unlocked()"
Linus Torvalds [Thu, 31 Mar 2016 12:13:56 +0000 (07:13 -0500)]
Merge tag 'gpio-v4.6-2' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are two GPIO fixes for the v4.6 series, both in drivers:
- Prevent NULL dereference in the Xgene driver
- Fix an uninitialized spinlock in the menz127 driver"
* tag 'gpio-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: xgene: Prevent NULL pointer dereference
gpio: menz127: Drop lock field from struct men_z127_gpio
Linus Torvalds [Thu, 31 Mar 2016 11:56:50 +0000 (06:56 -0500)]
Merge branch 'libnvdimm-for-next' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull nvdimm mcsafe_memcpy use from Dan Williams:
"Now that mcsafe_memcpy() has landed, and the return value was been
clarified in commit
cbf8b5a2b649 ("x86/mm, x86/mce: Fix return
type/value for memcpy_mcsafe()"), let's hook up its primary usage in
the pmem driver.
The compilation problems from the initial posting have been fixed,
this has appeared in a -next release with no reported issues, and it
picked up an ack from Ingo. There is no pressing need to merge this
in 4.6- rc2. However, if we wait until 4.7 the new memcpy_mcsafe()
capability will ship without a user in 4.6-final"
* 'libnvdimm-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
x86, pmem: use memcpy_mcsafe() for memcpy_from_pmem()
Helge Deller [Wed, 30 Mar 2016 12:14:31 +0000 (14:14 +0200)]
parisc: Fix and enable seccomp filter support
The seccomp filter support requires careful handling of task registers. This
includes reloading of the return value (%r28) and proper syscall exit if
secure_computing() returned -1.
Additionally we need to sign-extend the syscall number from signed 32bit to
signed 64bit in do_syscall_trace_enter() since the ptrace interface only allows
storing 32bit values in compat mode.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v4.5
Helge Deller [Wed, 30 Mar 2016 12:11:50 +0000 (14:11 +0200)]
parisc: Fix SIGSYS signals in compat case
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v4.5
Al Viro [Thu, 31 Mar 2016 04:23:05 +0000 (00:23 -0400)]
fix the braino in "namei: massage lookup_slow() to be usable by lookup_one_len_unlocked()"
We should try to trigger automount *before* bailing out on negative dentry.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Thu, 31 Mar 2016 01:40:42 +0000 (20:40 -0500)]
Merge tag 'nios2-v4.6-rc2' of git://git./linux/kernel/git/lftan/nios2
Pull nios2 fix from Ley Foon Tan:
"Replace fdt_translate_address with of_flat_dt_translate_address"
Fixes a build failure.
* tag 'nios2-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: Replace fdt_translate_address with of_flat_dt_translate_address
Guenter Roeck [Tue, 29 Mar 2016 09:02:13 +0000 (17:02 +0800)]
nios2: Replace fdt_translate_address with of_flat_dt_translate_address
nios2 builds fail with the following build error.
arch/nios2/kernel/prom.c: In function 'early_init_dt_scan_serial':
arch/nios2/kernel/prom.c:100:2: error:
implicit declaration of function 'fdt_translate_address'
Commit
c90fe9c0394b ("of: earlycon: Move address translation to
of_setup_earlycon()") replaced fdt_translate_address() with
of_flat_dt_translate_address() but missed updating the nios2 code.
Fixes:
c90fe9c0394b ("of: earlycon: Move address translation to of_setup_earlycon()")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Ley Foon Tan <lftan@altera.com>
Daniel Borkmann [Tue, 29 Mar 2016 22:02:00 +0000 (00:02 +0200)]
bpf: make padding in bpf_tunnel_key explicit
Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.
Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.
Fixes:
4018ab1875e0 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 29 Mar 2016 15:43:41 +0000 (08:43 -0700)]
ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
IPv6 counters updates use a different macro than IPv4.
Fixes:
36cbb2452cbaf ("udp: Increment UDP_MIB_IGNOREDMULTI for arriving unmatched multicasts")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 28 Mar 2016 23:46:07 +0000 (19:46 -0400)]
bnxt_en: Fix ethtool -a reporting.
To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl. Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 28 Mar 2016 23:46:06 +0000 (19:46 -0400)]
bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
The typo caused the wrong flow control bit to be set.
Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 28 Mar 2016 23:46:05 +0000 (19:46 -0400)]
bnxt_en: Implement proper firmware message padding.
The size of every padded firmware message is specified in the first
HWRM_VER_GET response message. Use this value to pad every message
after that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prashant Sreedharan [Mon, 28 Mar 2016 23:46:04 +0000 (19:46 -0400)]
bnxt_en: Initialize CP doorbell value before ring allocation
The existing code does the following:
allocate completion ring
initialize completion ring doorbell
disable interrupts on this completion ring by writing to the doorbell
We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 30 Mar 2016 02:58:39 +0000 (10:58 +0800)]
team: team should sync the port's uc/mc addrs when add a port
There is an issue when we use mavtap over team:
When we replug nic links from team0, the real nics's mc list will not
include the maddr for macvtap any more. then we can't receive pkts to
macvtap device, as they are filterred by mc list of nic.
In Bonding Driver, it syncs the uc/mc addrs in bond_enslave().
We will fix this issue on team by adding the port's uc/mc addrs sync in
team_port_add.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Tue, 29 Mar 2016 21:55:22 +0000 (14:55 -0700)]
gro: Allow tunnel stacking in the case of FOU/GUE
This patch should fix the issues seen with a recent fix to prevent
tunnel-in-tunnel frames from being generated with GRO. The fix itself is
correct for now as long as we do not add any devices that support
NETIF_F_GSO_GRE_CSUM. When such a device is added it could have the
potential to mess things up due to the fact that the outer transport header
points to the outer UDP header and not the GRE header as would be expected.
Fixes:
fac8e0f579695 ("tunnels: Don't apply GRO to multiple layers of encapsulation.")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 29 Mar 2016 17:00:50 +0000 (18:00 +0100)]
qed: initialize return rc to avoid returning garbage
in the case where qed_slowpath_irq_req is not called, rc is not
assigned and so qed_int_igu_enable will return a garbage value.
Fix this by initializing rc to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner [Tue, 29 Mar 2016 13:41:03 +0000 (10:41 -0300)]
sctp: really allow using GFP_KERNEL on sctp_packet_transmit
Somehow my patch for commit
cea8768f333e ("sctp: allow
sctp_transmit_packet and others to use gfp") missed two important
chunks, which are now added.
Fixes:
cea8768f333e ("sctp: allow sctp_transmit_packet and others to use gfp")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Tue, 29 Mar 2016 10:48:08 +0000 (18:48 +0800)]
bridge: Allow set bridge ageing time when switchdev disabled
When NET_SWITCHDEV=n, switchdev_port_attr_set will return -EOPNOTSUPP,
we should ignore this error code and continue to set the ageing time.
Fixes:
c62987bbd8a1 ("bridge: push bridge setting ageing_time down to switchdev")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 30 Mar 2016 18:28:34 +0000 (13:28 -0500)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug in pkcs7_validate_trust and its users where the
output value may in fact be taken from uninitialised memory"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
PKCS#7: pkcs7_validate_trust(): initialize the _trusted output argument