Huang Ying [Wed, 13 Jul 2011 05:14:13 +0000 (13:14 +0800)]
ACPI, APEI, ERST, Prevent erst_dbg from loading if ERST is disabled
erst_dbg module can not work when ERST is disabled. So disable module
loading to provide clearer information to user.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Huang Ying [Wed, 13 Jul 2011 05:14:12 +0000 (13:14 +0800)]
ACPI, APEI, HEST, Detect duplicated hardware error source ID
The firmware on some machine will report duplicated hardware error
source ID in HEST. This is considered a firmware bug. To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.
This patch fixes #37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412
Reported-by: marconifabio@ubuntu-it.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Tested-by: Mathias <janedo.spam@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Tue, 12 Jul 2011 21:21:19 +0000 (14:21 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
Linus Torvalds [Tue, 12 Jul 2011 21:19:51 +0000 (14:19 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting
ARM: pxa/raumfeld: fix device name for codec ak4104
ARM: pxa/raumfeld: display initialisation fixes
ARM: pxa/raumfeld: adapt to upcoming hardware change
ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
arm: mach-vt8500: add forgotten irq_data conversion
ARM: pxa168: correct nand pmu setting
ARM: pxa910: correct nand pmu setting
ARM: pxa: fix PGSR register address calculation
Linus Torvalds [Tue, 12 Jul 2011 21:18:00 +0000 (14:18 -0700)]
Merge branch 'drm-intel-fixes' of git://git./linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable GPU reset on Ivybridge.
drm/i915/dp: manage sink power state if possible
drm/i915/dp: consolidate AUX retry code
drm/i915/dp: remove DPMS mode tracking from DP
drm/i915/dp: try to read receiver capabilities 3 times when detecting
drm/i915/dp: read more receiver capability bits on hotplug
drm/i915/dp: use DP DPCD defines when looking at DPCD values
drm/i915/dp: retry link status read 3 times on failure
Chris Wilson [Tue, 12 Jul 2011 17:03:29 +0000 (18:03 +0100)]
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
...which is measured by the size and not the amount of space remaining.
Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:
[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 12 Jul 2011 15:49:31 +0000 (08:49 -0700)]
Revert "drm/i915: enable rc6 by default"
This reverts commit
a51f7a66fb5e4af5ec4286baef940d06594b59d2.
We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 10 Jul 2011 20:12:17 +0000 (13:12 -0700)]
drm/i915: Clean up i915_driver_load failure path
i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
Benjamin Herrenschmidt [Tue, 14 Jun 2011 00:57:51 +0000 (10:57 +1000)]
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
Just compiling pseries in the kernel causes it to override
memory_block_size_bytes() regardless of what is the runtime
platform.
This cleans up the implementation of that function, fixing
a bug or two while at it, so that it's harmless (and potentially
useful) for other platforms. Without this, bugs in that code
would trigger a WARN_ON() in drivers/base/memory.c when
booting some different platforms.
If/when we have another platform supporting memory hotplug we
might want to either move that out to a generic place or
make it a ppc_md. callback.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 14 Jun 2011 00:57:50 +0000 (10:57 +1000)]
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Mon, 11 Jul 2011 23:51:52 +0000 (16:51 -0700)]
Linux 3.0-rc7
Linus Torvalds [Mon, 11 Jul 2011 23:48:38 +0000 (16:48 -0700)]
Documentation/Changes: remove some really obsolete text
That file harkens back to the days of the big 2.4 -> 2.6 version jump,
and was based even then on older versions. Some of it is just obsolete,
and Jesper Juhl points out that it talks about kernel versions 2.6 and
should be updated to 3.0.
Remove some obsolete text, and re-phrase some other to not be 2.6-specific.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 11 Jul 2011 23:43:27 +0000 (16:43 -0700)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
Arnd Bergmann [Mon, 11 Jul 2011 21:26:16 +0000 (23:26 +0200)]
Merge branch 'fix' of git://git./linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
Linus Torvalds [Mon, 11 Jul 2011 19:49:03 +0000 (12:49 -0700)]
Merge branch 'pm-fixes' of git://git./linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Reintroduce dropped call to check_wakeup_irqs
Linus Torvalds [Mon, 11 Jul 2011 19:48:24 +0000 (12:48 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: drop spinlock before calling cifs_put_tlink
cifs: fix expand_dfs_referral
cifs: move bdi_setup_and_register outside of CONFIG_CIFS_DFS_UPCALL
cifs: factor smb_vol allocation out of cifs_setup_volume_info
cifs: have cifs_cleanup_volume_info not take a double pointer
cifs: fix build_unc_path_to_root to account for a prefixpath
cifs: remove bogus call to cifs_cleanup_volume_info
Linus Torvalds [Mon, 11 Jul 2011 19:47:53 +0000 (12:47 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] fix cpumask memory leak in acpi-cpufreq on cpu hotplug.
Linus Torvalds [Mon, 11 Jul 2011 19:47:09 +0000 (12:47 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
hp-wmi: fix use after free
dell-laptop - using buffer without mutex_lock
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
drivers/platform/x86: Fix memory leak
thinkpad-acpi: handle some new HKEY 0x60xx events
acer-wmi: fix bitwise bug when set device state
acer-wmi: Only update rfkill status for associated hotkey events
Linus Torvalds [Mon, 11 Jul 2011 19:46:39 +0000 (12:46 -0700)]
Merge branch 'movieboard' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'movieboard' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: do not bind to Pinnacle cards, avert panic
Joe Perches [Sun, 10 Jul 2011 09:28:26 +0000 (02:28 -0700)]
ath5k: Add missing breaks in switch/case
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Muthu Kumar [Mon, 11 Jul 2011 18:04:58 +0000 (11:04 -0700)]
Documentation/spinlocks.txt: Remove reference to sti()/cli()
Since we removed sti()/cli() and related, how about removing it from
Documentation/spinlocks.txt?
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Mon, 11 Jul 2011 14:16:34 +0000 (10:16 -0400)]
cifs: drop spinlock before calling cifs_put_tlink
...as that function can sleep.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Eric Dumazet [Mon, 11 Jul 2011 10:22:21 +0000 (12:22 +0200)]
hp-wmi: fix use after free
[ 191.310008] WARNING: kmemcheck: Caught 32-bit read from freed memory (
f0d25f14)
[ 191.310011] c056d2f088000000105fd2f00000000050415353040000000000000000000000
[ 191.310020] i i i i f f f f f f f f f f f f f f f f f f f f f f f f f f f f
[ 191.310027] ^
[ 191.310029]
[ 191.310032] Pid: 737, comm: modprobe Not tainted 3.0.0-rc5+ #268 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[ 191.310036] EIP: 0060:[<
f80b3104>] EFLAGS:
00010286 CPU: 0
[ 191.310039] EIP is at hp_wmi_perform_query+0x104/0x150 [hp_wmi]
[ 191.310041] EAX:
f0d25601 EBX:
f0d25f00 ECX:
000121cf EDX:
000121ce
[ 191.310043] ESI:
f0d25f10 EDI:
f0f97ea8 EBP:
f0f97ec4 ESP:
c173f34c
[ 191.310045] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 191.310046] CR0:
8005003b CR2:
f540c000 CR3:
30f30000 CR4:
000006d0
[ 191.310048] DR0:
00000000 DR1:
00000000 DR2:
00000000 DR3:
00000000
[ 191.310050] DR6:
ffff4ff0 DR7:
00000400
[ 191.310051] [<
f80b317b>] hp_wmi_dock_state+0x2b/0x40 [hp_wmi]
[ 191.310054] [<
f80b6093>] hp_wmi_init+0x93/0x1a8 [hp_wmi]
[ 191.310057] [<
c10011f0>] do_one_initcall+0x30/0x170
[ 191.310061] [<
c107ab9f>] sys_init_module+0xef/0x1a60
[ 191.310064] [<
c149f998>] sysenter_do_call+0x12/0x28
[ 191.310067] [<
ffffffff>] 0xffffffff
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Jose Alonso [Sun, 10 Jul 2011 18:46:51 +0000 (15:46 -0300)]
dell-laptop - using buffer without mutex_lock
Using buffer->output[1] without mutex_lock()
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Keng-Yu Lin [Mon, 27 Jun 2011 10:19:03 +0000 (11:19 +0100)]
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
This reverts commit
a3d77411e8b2ad661958c1fbee65beb476ec6d70,
as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.
Cc: stable@kernel.org
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Colin Cross [Mon, 11 Jul 2011 08:51:49 +0000 (10:51 +0200)]
PM: Reintroduce dropped call to check_wakeup_irqs
Patch
2e711c04dbbf7a7732a3f7073b1fc285d12b369d
(PM: Remove sysdev suspend, resume and shutdown operations)
deleted sysdev_suspend(), which was being relied on to call
check_wakeup_irqs() in suspend. If check_wakeup_irqs() is not
called, wake interrupts that are pending when suspend is
entered may be lost. It also breaks IRQCHIP_MASK_ON_SUSPEND,
which is handled in check_wakeup_irqs().
This patch adds a call to check_wakeup_irqs() in syscore_suspend(),
similar to what was deleted in sysdev_suspend().
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Jonathan Cameron [Mon, 6 Jun 2011 14:24:13 +0000 (15:24 +0100)]
pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Daniel Mack [Wed, 25 May 2011 11:37:33 +0000 (13:37 +0200)]
ARM: pxa/raumfeld: fix device name for codec ak4104
In commit
f0fba2ad (ASoC: multi-component - ASoC Multi-Component
Support), the name of the ak4104 codec driver was changed without
amending the platform code which uses it as well.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Sven Neumann [Wed, 25 May 2011 11:37:32 +0000 (13:37 +0200)]
ARM: pxa/raumfeld: display initialisation fixes
The display requires some milliseconds between GPIO_TFT_VA_EN
and GPIO_DISPLAY_ENABLE. Reorder initialisation to comply with
the display spec.
Also tune timings for better compliance with the spec.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Sven Neumann [Wed, 25 May 2011 11:37:31 +0000 (13:37 +0200)]
ARM: pxa/raumfeld: adapt to upcoming hardware change
The backlight control is going to change back to PWM in the
upcoming Raumfeld Controller hardware revision.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Linus Walleij [Mon, 13 Jun 2011 08:42:19 +0000 (10:42 +0200)]
ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace
The PXA platform code has a static inline helper called
gpio_to_chip which clashes with the gpiolib namespace if we
try to expose the function with the same name from gpiolib,
and it's still confusing even if we don't do that. So rename
it to gpio_to_pxachip().
Reported-by: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Luming Yu [Fri, 8 Jul 2011 20:37:44 +0000 (16:37 -0400)]
[CPUFREQ] fix cpumask memory leak in acpi-cpufreq on cpu hotplug.
I came across a memory leak during a cyclic cpu-online-offline test.
Signed-off-by: Yu Luming <luming.yu@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Linus Torvalds [Sun, 10 Jul 2011 17:24:47 +0000 (10:24 -0700)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (pmbus) Improve auto-detection of temperature status register
hwmon: (lm95241) Fix negative temperature results
hwmon: (lm95241) Fix chip detection code
Guenter Roeck [Sun, 3 Jul 2011 20:08:03 +0000 (13:08 -0700)]
hwmon: (pmbus) Improve auto-detection of temperature status register
It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+
Guenter Roeck [Thu, 30 Jun 2011 09:09:37 +0000 (02:09 -0700)]
hwmon: (lm95241) Fix negative temperature results
Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.
Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+
Linus Torvalds [Sun, 10 Jul 2011 14:29:22 +0000 (07:29 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix a copmile warning
ASoC: ak4642: fixup snd_soc_update_bits mask for PW_MGMT2
ALSA: hda - Change all ADCs for dual-adc switching mode for Realtek
ASoC: Manage WM8731 ACTIVE bit as a supply widget
ASoC: Don't set invalid name string to snd_card->driver field
ASoC: Ensure we delay long enough for WM8994 FLL to lock when starting
ASoC: Tegra: I2S: Ensure clock is enabled when writing regs
ASoC: Fix Blackfin I2S _pointer() implementation return in bounds values
ASoC: tlv320aic3x: Do soft reset to codec when going to bias off state
ASoC: tlv320aic3x: Don't sync first two registers from register cache
audio: tlv320aic26: fix PLL register configuration
Linus Torvalds [Sun, 10 Jul 2011 14:28:51 +0000 (07:28 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: conditional resource-reallocation through kernel parameter pci=realloc
Linus Torvalds [Sun, 10 Jul 2011 14:28:30 +0000 (07:28 -0700)]
Merge branch 'fixes' of /home/rmk/linux-2.6-arm
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6994/1: smp_twd: Fix typo in 'twd_timer_rate' printing
ARM: 6987/1: l2x0: fix disabling function to avoid deadlock
ARM: 6966/1: ep93xx: fix inverted RTS/DTR signals on uart1
ARM: 6980/1: mmci: use StartBitErr to detect bad connections
ARM: 6979/1: mach-vt8500: add forgotten irq_data conversion
ARM: move memory layout sanity checking before meminfo initialization
ARM: 6990/1: MAINTAINERS: add entry for ARM PMU profiling and debugging
ARM: 6989/1: perf: do not start the PMU when no events are present
ARM: dmabounce: fix map_single() error return value
Linus Torvalds [Sun, 10 Jul 2011 14:27:45 +0000 (07:27 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: clean up multiple crtc handling for evergreen+ (v2)
Stefan Richter [Sat, 9 Jul 2011 22:23:03 +0000 (00:23 +0200)]
firewire: ohci: do not bind to Pinnacle cards, avert panic
When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a
"Register access failure" is logged and an interrupt storm or a kernel
panic happens. https://bugzilla.kernel.org/show_bug.cgi?id=36622
Until this is sorted out (if that is going to succeed at all), let's
just prevent firewire-ohci from touching these devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
Jeff Layton [Wed, 6 Jul 2011 12:10:39 +0000 (08:10 -0400)]
cifs: fix expand_dfs_referral
Regression introduced in commit
724d9f1cfba.
Prior to that, expand_dfs_referral would regenerate the mount data string
and then call cifs_parse_mount_options to re-parse it (klunky, but it
worked). The above commit moved cifs_parse_mount_options out of cifs_mount,
so the re-parsing of the new mount options no longer occurred. Fix it by
making expand_dfs_referral re-parse the mount options.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Sat, 9 Jul 2011 16:21:07 +0000 (12:21 -0400)]
cifs: move bdi_setup_and_register outside of CONFIG_CIFS_DFS_UPCALL
This needs to be done regardless of whether that KConfig option is set
or not.
Reported-by: Sven-Haegar Koch <haegar@sdinet.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Takashi Iwai [Sat, 9 Jul 2011 09:56:43 +0000 (11:56 +0200)]
Merge branch 'fix/asoc' into for-linus
Takashi Iwai [Sat, 9 Jul 2011 09:55:28 +0000 (11:55 +0200)]
ALSA: hda - Fix a copmile warning
It's harmless but annyoing.
sound/pci/hda/patch_realtek.c: In function ‘alc_cap_getput_caller’:
sound/pci/hda/patch_realtek.c:2722:9: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Sat, 9 Jul 2011 07:44:09 +0000 (09:44 +0200)]
Merge branch 'for-3.0' of git://git./linux/kernel/git/broonie/sound-2.6 into fix/asoc
Linus Torvalds [Sat, 9 Jul 2011 06:28:23 +0000 (23:28 -0700)]
Merge branch 's5p-fixes-for-linus' of git://git./linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C2440: fix section mismatch on mini2440
ARM: S3C24XX: drop return codes in void function of dma.c
ARM: S3C24XX: don't use uninitialized variable in dma.c
ARM: EXYNOS4: Set appropriate I2C device variant
ARM: S5PC100: Fix for compilation error
spi/s3c64xx: Bug fix for SPI with different FIFO level
ARM: SAMSUNG: Add tx_st_done variable
ARM: EXYNOS4: Address a section mismatch w/ suspend issue.
ARM: S5P: Fix bug on init of PWMTimers for HRTimer
ARM: SAMSUNG: header file revised to prevent declaring duplicated
ARM: EXYNOS4: fix improper gpio configuration
ARM: EXYNOS4: Fix card detection for sdhci 0 and 2
Linus Torvalds [Sat, 9 Jul 2011 06:26:28 +0000 (23:26 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: max8997: Fix setting inappropriate value for ramp_delay variable
regulator: db8500-prcmu: small fixes
regulator: max8997: remove dependency on platform_data pointer
regulator: MAX8997: Fix for divide by zero error
regulator: max8952 - fix wrong gpio valid check
Linus Torvalds [Sat, 9 Jul 2011 06:25:45 +0000 (23:25 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
btrfs: fix oops when doing space balance
Btrfs: don't panic if we get an error while balancing V2
btrfs: add missing options displayed in mount output
Bjorn Helgaas [Fri, 8 Jul 2011 22:39:48 +0000 (15:39 -0700)]
MAINTAINERS: update Bjorn Helgaas's email address
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wolfram Sang [Fri, 8 Jul 2011 22:39:46 +0000 (15:39 -0700)]
drivers/leds/leds-pca9532.c: change driver name to be unique
This driver handles the variants pca9530-pca9533, so it chose the name
"pca953x". However, there is a gpio driver which decided on the same
name. As a result, those two can't be loaded at the same time. Add a
subsystem prefix to make the driver name unique. Device matching will not
suffer, because both are I2C drivers which match using a
i2c_device_id-table which is not altered.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bob Liu [Fri, 8 Jul 2011 22:39:46 +0000 (15:39 -0700)]
mm/nommu.c: fix remap_pfn_range()
remap_pfn_range() means map physical address pfn<<PAGE_SHIFT to user addr.
For nommu arch it's implemented by vma->vm_start = pfn << PAGE_SHIFT which
is wrong acroding the original meaning of this function. And some driver
developer using remap_pfn_range() with correct parameter will get
unexpected result because vm_start is changed. It should be implementd
like addr = pfn << PAGE_SHIFT but which is meanless on nommu arch, this
patch just make it simply return.
Parameter name and setting of vma->vm_flags also be fixed.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean-François Dagenais [Fri, 8 Jul 2011 22:39:44 +0000 (15:39 -0700)]
w1: ds1wm: add a reset recovery parameter
This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KAMEZAWA Hiroyuki [Fri, 8 Jul 2011 22:39:43 +0000 (15:39 -0700)]
memcg: fix numa scan information update to be triggered by memory event
commit
889976dbcb12 ("memcg: reclaim memory from nodes in round-robin
order") adds an numa node round-robin for memcg. But the information is
updated once per 10sec.
This patch changes the update trigger from jiffies to memcg's event count.
After this patch, numa scan information will be updated when we see 1024
events of pagein/pageout under a memcg.
[akpm@linux-foundation.org: attempt to repair code layout]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ying Han <yinghan@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KAMEZAWA Hiroyuki [Fri, 8 Jul 2011 22:39:42 +0000 (15:39 -0700)]
memcg: fix reclaimable lru check in memcg
Now, in mem_cgroup_hierarchical_reclaim(), mem_cgroup_local_usage() is
used for checking whether the memcg contains reclaimable pages or not. If
no pages in it, the routine skips it.
But, mem_cgroup_local_usage() contains Unevictable pages and cannot handle
"noswap" condition correctly. This doesn't work on a swapless system.
This patch adds test_mem_cgroup_reclaimable() and replaces
mem_cgroup_local_usage(). test_mem_cgroup_reclaimable() see LRU counter
and returns correct answer to the caller. And this new function has
"noswap" argument and can see only FILE LRU if necessary.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix kerneldoc layout]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ying Han <yinghan@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohua Li [Fri, 8 Jul 2011 22:39:41 +0000 (15:39 -0700)]
mm: __tlb_remove_page() check the correct batch
__tlb_remove_page() switches to a new batch page, but still checks space
in the old batch. This check always fails, and causes a forced tlb flush.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Fri, 8 Jul 2011 22:39:40 +0000 (15:39 -0700)]
mm: vmscan: only read new_classzone_idx from pgdat when reclaiming successfully
During allocator-intensive workloads, kswapd will be woken frequently
causing free memory to oscillate between the high and min watermark. This
is expected behaviour. Unfortunately, if the highest zone is small, a
problem occurs.
When balance_pgdat() returns, it may be at a lower classzone_idx than it
started because the highest zone was unreclaimable. Before checking if it
should go to sleep though, it checks pgdat->classzone_idx which when there
is no other activity will be MAX_NR_ZONES-1. It interprets this as it has
been woken up while reclaiming, skips scheduling and reclaims again. As
there is no useful reclaim work to do, it enters into a loop of shrinking
slab consuming loads of CPU until the highest zone becomes reclaimable for
a long period of time.
There are two problems here. 1) If the returned classzone or order is
lower, it'll continue reclaiming without scheduling. 2) if the highest
zone was marked unreclaimable but balance_pgdat() returns immediately at
DEF_PRIORITY, the new lower classzone is not communicated back to kswapd()
for sleeping.
This patch does two things that are related. If the end_zone is
unreclaimable, this information is communicated back. Second, if the
classzone or order was reduced due to failing to reclaim, new information
is not read from pgdat and instead an attempt is made to go to sleep. Due
to this, it is also necessary that pgdat->classzone_idx be initialised
each time to pgdat->nr_zones - 1 to avoid re-reads being interpreted as
wakeups.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Fri, 8 Jul 2011 22:39:39 +0000 (15:39 -0700)]
mm: vmscan: evaluate the watermarks against the correct classzone
When deciding if kswapd is sleeping prematurely, the classzone is taken
into account but this is different to what balance_pgdat() and the
allocator are doing. Specifically, the DMA zone will be checked based on
the classzone used when waking kswapd which could be for a GFP_KERNEL or
GFP_HIGHMEM request. The lowmem reserve limit kicks in, the watermark is
not met and kswapd thinks it's sleeping prematurely keeping kswapd awake in
error.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Acked-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Fri, 8 Jul 2011 22:39:38 +0000 (15:39 -0700)]
mm: vmscan: do not apply pressure to slab if we are not applying pressure to zone
During allocator-intensive workloads, kswapd will be woken frequently
causing free memory to oscillate between the high and min watermark. This
is expected behaviour.
When kswapd applies pressure to zones during node balancing, it checks if
the zone is above a high+balance_gap threshold. If it is, it does not
apply pressure but it unconditionally shrinks slab on a global basis which
is excessive. In the event kswapd is being kept awake due to a high small
unreclaimable zone, it skips zone shrinking but still calls shrink_slab().
Once pressure has been applied, the check for zone being unreclaimable is
being made before the check is made if all_unreclaimable should be set.
This miss of unreclaimable can cause has_under_min_watermark_zone to be
set due to an unreclaimable zone preventing kswapd backing off on
congestion_wait().
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Acked-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Fri, 8 Jul 2011 22:39:36 +0000 (15:39 -0700)]
mm: vmscan: correct check for kswapd sleeping in sleeping_prematurely
During allocator-intensive workloads, kswapd will be woken frequently
causing free memory to oscillate between the high and min watermark. This
is expected behaviour. Unfortunately, if the highest zone is small, a
problem occurs.
This seems to happen most with recent sandybridge laptops but it's
probably a co-incidence as some of these laptops just happen to have a
small Normal zone. The reproduction case is almost always during copying
large files that kswapd pegs at 100% CPU until the file is deleted or
cache is dropped.
The problem is mostly down to sleeping_prematurely() keeping kswapd awake
when the highest zone is small and unreclaimable and compounded by the
fact we shrink slabs even when not shrinking zones causing a lot of time
to be spent in shrinkers and a lot of memory to be reclaimed.
Patch 1 corrects sleeping_prematurely to check the zones matching
the classzone_idx instead of all zones.
Patch 2 avoids shrinking slab when we are not shrinking a zone.
Patch 3 notes that sleeping_prematurely is checking lower zones against
a high classzone which is not what allocators or balance_pgdat()
is doing leading to an artifical belief that kswapd should be
still awake.
Patch 4 notes that when balance_pgdat() gives up on a high zone that the
decision is not communicated to sleeping_prematurely()
This problem affects 2.6.38.8 for certain and is expected to affect 2.6.39
and 3.0-rc4 as well. If accepted, they need to go to -stable to be picked
up by distros and this series is against 3.0-rc4. I've cc'd people that
reported similar problems recently to see if they still suffer from the
problem and if this fixes it.
This patch: correct the check for kswapd sleeping in sleeping_prematurely()
During allocator-intensive workloads, kswapd will be woken frequently
causing free memory to oscillate between the high and min watermark. This
is expected behaviour.
A problem occurs if the highest zone is small. balance_pgdat() only
considers unreclaimable zones when priority is DEF_PRIORITY but
sleeping_prematurely considers all zones. It's possible for this sequence
to occur
1. kswapd wakes up and enters balance_pgdat()
2. At DEF_PRIORITY, marks highest zone unreclaimable
3. At DEF_PRIORITY-1, ignores highest zone setting end_zone
4. At DEF_PRIORITY-1, calls shrink_slab freeing memory from
highest zone, clearing all_unreclaimable. Highest zone
is still unbalanced
5. kswapd returns and calls sleeping_prematurely
6. sleeping_prematurely looks at *all* zones, not just the ones
being considered by balance_pgdat. The highest small zone
has all_unreclaimable cleared but the zone is not
balanced. all_zones_ok is false so kswapd stays awake
This patch corrects the behaviour of sleeping_prematurely to check the
zones balance_pgdat() checked.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Pádraig Brady <P@draigBrady.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Acked-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guenter Roeck [Mon, 27 Jun 2011 18:22:46 +0000 (11:22 -0700)]
hwmon: (lm95241) Fix chip detection code
The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its
own, and other chips such as LM95245 use chip IDs in the accepted ID range.
This results in false chip detection.
Fix problem by accepting only the known LM95241 chip ID.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+
Ram Pai [Thu, 7 Jul 2011 18:19:10 +0000 (11:19 -0700)]
PCI: conditional resource-reallocation through kernel parameter pci=realloc
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Donggeun Kim [Thu, 7 Jul 2011 07:51:56 +0000 (16:51 +0900)]
regulator: max8997: Fix setting inappropriate value for ramp_delay variable
The ramp_delay variable can be set lower than the desired value.
This patch fixes it.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Wed, 6 Jul 2011 03:41:12 +0000 (11:41 +0800)]
regulator: db8500-prcmu: small fixes
Small cleanups for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MyungJoo Ham [Mon, 20 Jun 2011 08:30:17 +0000 (17:30 +0900)]
regulator: max8997: remove dependency on platform_data pointer
The platform_data (pdata) may be pointing to __initdata section, which
may be free'd from the memory. The dependency on pdata in non-init
functions is removed in this patch to allow platform to declare
__initdata for platform data.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tushar Behera [Tue, 21 Jun 2011 03:38:59 +0000 (09:08 +0530)]
regulator: MAX8997: Fix for divide by zero error
Currently, ramp_delay variable is used uninitialzed in
max8997_set_voltage_ldobuck which gets called through
regulator_register calls.
To fix the problem, in max8997_pmic_probe, ramp_delay initialization
code is moved before calls to regulator_register.
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Jonghwan Choi [Wed, 15 Jun 2011 08:54:12 +0000 (17:54 +0900)]
regulator: max8952 - fix wrong gpio valid check
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Alex Deucher [Fri, 8 Jul 2011 15:44:56 +0000 (11:44 -0400)]
drm/radeon/kms: clean up multiple crtc handling for evergreen+ (v2)
evergreen+ asics have 2-6 crtcs. Don't access crtc registers
for crtc regs that don't exist as they have very high latency
and may cause problems on some asics. The previous code missed
a few cases and was not fine grained enough (missed the 4 crtc
case for example).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38800
v2: fix typo noticed by Chris Bandy <cbandy@jbandy.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Fri, 8 Jul 2011 16:01:11 +0000 (09:01 -0700)]
Merge branch 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio/langwell_gpio: ack the correct bit for langwell gpio interrupts
Linus Torvalds [Fri, 8 Jul 2011 16:00:51 +0000 (09:00 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: unpin stale inodes directly in IOP_COMMITTED
Linus Torvalds [Fri, 8 Jul 2011 16:00:02 +0000 (09:00 -0700)]
Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: drop __initdata tags from static struct platform_device declarations
Linus Torvalds [Fri, 8 Jul 2011 15:59:39 +0000 (08:59 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: allow drm_mode_group with no objects
drm/radeon/kms: free ib pool on module unloading
drm/radeon/kms: fix typo in evergreen disp int status register
drm/radeon/kms: fix typo in IH_CNTL swap bitfield
Mathias Nyman [Fri, 8 Jul 2011 09:02:18 +0000 (10:02 +0100)]
gpio/langwell_gpio: ack the correct bit for langwell gpio interrupts
The wrong bit was masked when acking langwell gpio interrupts.
Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)
This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b92bb727b27e61580ce278dddefe31c6ad
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Wolfram Sang [Fri, 8 Jul 2011 09:16:56 +0000 (18:16 +0900)]
ARM: S3C2440: fix section mismatch on mini2440
If mini2440_init() is in __init, mini2440_parse_features() should also
be in __init. Fixes:
(.text+0x9adc): Section mismatch in reference from the function mini2440_parse_features.clone.0() to the
(unknown reference) .init.data:(unknown)
The function mini2440_parse_features.clone.0() references the (unknown reference) __initdata (unknown).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Michel Pollet <buserror@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Wolfram Sang [Fri, 8 Jul 2011 05:33:02 +0000 (14:33 +0900)]
ARM: S3C24XX: drop return codes in void function of dma.c
Commit
bb072c3c (ARM / Samsung: Use struct syscore_ops for "core" power
management) turned s3c2410_dma_resume_chan() from int to void. So, drop
the actual return values, too. Fixes:
arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_resume_chan':
arch/arm/plat-s3c24xx/dma.c:1238:3: warning: 'return' with a value, in function returning void
arch/arm/plat-s3c24xx/dma.c:1250:2: warning: 'return' with a value, in function returning void
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Wolfram Sang [Fri, 8 Jul 2011 05:33:02 +0000 (14:33 +0900)]
ARM: S3C24XX: don't use uninitialized variable in dma.c
Commit
8970ef47 (S3C24XX: Remove hardware specific registers from DMA
calls) removed the parameter dcon in s3c2410_dma_config() and calculates
it on its own. So the debug-output for the old parameter can go, too.
Fixes:
arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_config':
arch/arm/plat-s3c24xx/dma.c:1030:2: warning: 'dcon' is used uninitialized in this function
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Jeff Layton [Wed, 6 Jul 2011 12:10:38 +0000 (08:10 -0400)]
cifs: factor smb_vol allocation out of cifs_setup_volume_info
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Linus Torvalds [Thu, 7 Jul 2011 23:29:29 +0000 (16:29 -0700)]
Merge branch 'for-30-rc5/all-i2c' of git://git.fluff.org/bjdooks/linux
* 'for-30-rc5/all-i2c' of git://git.fluff.org/bjdooks/linux:
i2c-bfin-twi: abort transfer is MEM bit is reset unexpectedly
i2c-s3c2410: Remove useless break code
i2c-s3c2410: Fix typo 'i2s' -> 'i2c'
i2c: tegra: Assign unused slave address
Kenneth Graunke [Thu, 7 Jul 2011 22:33:26 +0000 (15:33 -0700)]
drm/i915: Enable GPU reset on Ivybridge.
According to the hardware documentation, GDRST is exactly the same as on
Sandybridge. So simply enable the existing code.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds [Thu, 7 Jul 2011 22:10:33 +0000 (15:10 -0700)]
Merge branch 'usb-linus' of git://git./linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: additional regression fix for device removal
Jesse Barnes [Thu, 7 Jul 2011 18:11:03 +0000 (11:11 -0700)]
drm/i915/dp: manage sink power state if possible
On sinks with a DPCD rev of 1.1 or greater, we can send sink power
management commands to address 0x600 per section 5.1.5 of the
DisplayPort 1.1a spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Thu, 7 Jul 2011 18:11:02 +0000 (11:11 -0700)]
drm/i915/dp: consolidate AUX retry code
When checking link status during a hot plug event or detecting sink
presence, we need to retry 3 times per the spec (section 9.1 of the 1.1a
DisplayPort spec). Consolidate the retry code into a
native_aux_read_retry function for use by get_link_status and _detect.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Thu, 7 Jul 2011 18:11:01 +0000 (11:11 -0700)]
drm/i915/dp: remove DPMS mode tracking from DP
We currently use this when a hot plug event is received, only checking
the link status and re-training if we had previously configured a link.
However if we want to preserve the DP configuration across both hot plug
and DPMS events (which we do for userspace apps that don't respond to
hot plug uevents), we need to unconditionally check the link and try to
bring it up on hot plug.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Thu, 7 Jul 2011 18:11:00 +0000 (11:11 -0700)]
drm/i915/dp: try to read receiver capabilities 3 times when detecting
If ->detect is called too soon after a hot plug event, the sink may not
be ready yet. So try up to 3 times with 1ms sleeps in between tries to
get the data (spec dictates that receivers must be ready to respond within
1ms and that sources should try 3 times).
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Thu, 7 Jul 2011 18:10:59 +0000 (11:10 -0700)]
drm/i915/dp: read more receiver capability bits on hotplug
When a hotplug event is received, we need to check the receiver cap bits
in case they've changed (as they might with a hub or chain config).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Thu, 7 Jul 2011 18:10:58 +0000 (11:10 -0700)]
drm/i915/dp: use DP DPCD defines when looking at DPCD values
Makes it easier to search for DP related constants.
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Thu, 7 Jul 2011 18:10:57 +0000 (11:10 -0700)]
drm/i915/dp: retry link status read 3 times on failure
Especially after a hotplug or power status change, the sink may not
reply immediately to a link status query. So retry 3 times per the spec
to really make sure nothing is there.
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Alan Stern [Wed, 6 Jul 2011 21:03:45 +0000 (17:03 -0400)]
USB: additional regression fix for device removal
Commit
e534c5b831c8b8e9f5edee5c8a37753c808b80dc (USB: fix regression
occurring during device removal) didn't go far enough. It failed to
take into account that when a driver claims multiple interfaces, it may
release them all at the same time. As a result, some interfaces can
get released before they are unregistered, and we deadlock trying to
acquire the bandwidth_mutex that we already own.
This patch (asl478) handles this case by setting the "unregistering"
flag on all the interfaces before removing any of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hans Verkuil [Sun, 26 Jun 2011 09:16:03 +0000 (06:16 -0300)]
[media] msp3400: fill in v4l2_tuner based on vt->type field
The vt->type field determines how the msp3400 should fill in the
tuner data, not whether the msp3400 is in radio mode or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Thu, 7 Jul 2011 20:22:41 +0000 (13:22 -0700)]
Merge branch 'pm-fixes' of git://git./linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Hibernate: Fix free_unnecessary_pages()
Linus Torvalds [Thu, 7 Jul 2011 20:22:26 +0000 (13:22 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
drbd: we should write meta data updates with FLUSH FUA
drbd: fix limit define, we support 1 PiByte now
drbd: when receive times out on meta socket, also check last receive time on data socket
drbd: account bitmap IO during resync as resync-(related-)-io
drbd: don't cond_resched_lock with IRQs disabled
drbd: add missing spinlock to bitmap receive
drbd: Use the correct max_bio_size when creating resync requests
cfq-iosched: make code consistent
cfq-iosched: fix a rcu warning
David Howells [Thu, 7 Jul 2011 11:19:48 +0000 (12:19 +0100)]
FS-Cache: Add a helper to bulk uncache pages on an inode
Add an FS-Cache helper to bulk uncache pages on an inode. This will
only work for the circumstance where the pages in the cache correspond
1:1 with the pages attached to an inode's page cache.
This is required for CIFS and NFS: When disabling inode cookie, we were
returning the cookie and setting cifsi->fscache to NULL but failed to
invalidate any previously mapped pages. This resulted in "Bad page
state" errors and manifested in other kind of errors when running
fsstress. Fix it by uncaching mapped pages when we disable the inode
cookie.
This patch should fix the following oops and "Bad page state" errors
seen during fsstress testing.
------------[ cut here ]------------
kernel BUG at fs/cachefiles/namei.c:201!
invalid opcode: 0000 [#1] SMP
Pid: 5, comm: kworker/u:0 Not tainted 2.6.38.7-30.fc15.x86_64 #1 Bochs Bochs
RIP: 0010: cachefiles_walk_to_object+0x436/0x745 [cachefiles]
RSP: 0018:
ffff88002ce6dd00 EFLAGS:
00010282
RAX:
ffff88002ef165f0 RBX:
ffff88001811f500 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
0000000000000100 RDI:
0000000000000282
RBP:
ffff88002ce6dda0 R08:
0000000000000100 R09:
ffffffff81b3a300
R10:
0000ffff00066c0a R11:
0000000000000003 R12:
ffff88002ae54840
R13:
ffff88002ae54840 R14:
ffff880029c29c00 R15:
ffff88001811f4b0
FS:
00007f394dd32720(0000) GS:
ffff88002ef00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
00007fffcb62ddf8 CR3:
000000001825f000 CR4:
00000000000006e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
Process kworker/u:0 (pid: 5, threadinfo
ffff88002ce6c000, task
ffff88002ce55cc0)
Stack:
0000000000000246 ffff88002ce55cc0 ffff88002ce6dd58 ffff88001815dc00
ffff8800185246c0 ffff88001811f618 ffff880029c29d18 ffff88001811f380
ffff88002ce6dd50 ffffffff814757e4 ffff88002ce6dda0 ffffffff8106ac56
Call Trace:
cachefiles_lookup_object+0x78/0xd4 [cachefiles]
fscache_lookup_object+0x131/0x16d [fscache]
fscache_object_work_func+0x1bc/0x669 [fscache]
process_one_work+0x186/0x298
worker_thread+0xda/0x15d
kthread+0x84/0x8c
kernel_thread_helper+0x4/0x10
RIP cachefiles_walk_to_object+0x436/0x745 [cachefiles]
---[ end trace
1d481c9af1804caa ]---
I tested the uncaching by the following means:
(1) Create a big file on my NFS server (
104857600 bytes).
(2) Read the file into the cache with md5sum on the NFS client. Look in
/proc/fs/fscache/stats:
Pages : mrk=25601 unc=0
(3) Open the file for read/write ("bash 5<>/warthog/bigfile"). Look in proc
again:
Pages : mrk=25601 unc=25601
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-Tested-by: Suresh Jayaraman <sjayaraman@suse.de>
cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hans Verkuil [Sun, 26 Jun 2011 08:35:34 +0000 (05:35 -0300)]
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
The tuner core should not silently change the type field in g_tuner and
g_frequency. If the tuner is in a different mode than the one that was
requested, then just fill in what you can and don't attempt to read afc,
signal or rxsubchans values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Thu, 7 Jul 2011 20:19:04 +0000 (13:19 -0700)]
Merge branch 'stable/bug.fixes' of git://git./linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Move check for acpi_sci_override_gsi to xen_setup_acpi_sci.
Linus Torvalds [Thu, 7 Jul 2011 20:18:13 +0000 (13:18 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Don't use the EFI reboot method by default
x86, suspend: Restore MISC_ENABLE MSR in realmode wakeup
x86, reboot: Acer Aspire One A110 reboot quirk
x86-32, NUMA: Fix boot regression caused by NUMA init unification on highmem machines
Linus Torvalds [Thu, 7 Jul 2011 20:17:45 +0000 (13:17 -0700)]
Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus' and 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debugobjects: Fix boot crash when kmemleak and debugobjects enabled
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
jump_label: Fix jump_label update for modules
oprofile, x86: Fix race in nmi handler while starting counters
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Disable (revert) SCHED_LOAD_SCALE increase
sched, cgroups: Fix MIN_SHARES on 64-bit boxen
Linus Torvalds [Thu, 7 Jul 2011 20:16:21 +0000 (13:16 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
sctp: fix missing send up SCTP_SENDER_DRY_EVENT when subscribe it
net: refine {udp|tcp|sctp}_mem limits
vmxnet3: round down # of queues to power of two
net: sh_eth: fix the parameter for the ETHER of SH7757
net: sh_eth: fix cannot work half-duplex mode
net: vlan: enable soft features regardless of underlying device
vmxnet3: fix starving rx ring whenoc_skb kb fails
bridge: Always flood broadcast packets
greth: greth_set_mac_add would corrupt the MAC address.
net: bind() fix error return on wrong address family
natsemi: silence dma-debug warnings
net: 8139too: Initial necessary vlan_features to support vlan
Fix call trace when interrupts are disabled while sleeping function kzalloc is called
qlge:Version change to v1.00.00.29
qlge: Fix printk priority so chip fatal errors are always reported.
qlge:Fix crash caused by mailbox execution on wedged chip.
xfrm4: Don't call icmp_send on local error
ipv4: Don't use ufo handling on later transformed packets
xfrm: Remove family arg from xfrm_bundle_ok
ipv6: Don't put artificial limit on routing table size.
...
Hans Verkuil [Sat, 25 Jun 2011 13:28:21 +0000 (10:28 -0300)]
[media] cx18/ivtv: fix g_tuner support
The driver shouldn't override vt->type, and the tuner name should be
based on vt->type as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 25 Jun 2011 13:24:49 +0000 (10:24 -0300)]
[media] tuner-core: power up tuner when called with s_power(1)
Drivers must be able to rely on s_power to power up subdevices.
Note that at this moment no driver attempts to power up tuners. This probably
isn't surprising since s_power(1) was never implemented in tuner-core.c until
now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 14 Jun 2011 07:03:26 +0000 (04:03 -0300)]
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
Prohibit attempts to change the tuner to a type that is different
from the device node the ioctl is called from. I.e. the type must
be RADIO for a radio node and ANALOG_TV for a video/vbi node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 13 Jun 2011 12:47:56 +0000 (09:47 -0300)]
[media] tuner-core: simplify the standard fixup
Get rid of a number of unnecessary tuner_dbg messages by simplifying
the std fixup function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>