xhci: re-initialize the HC during resume if HCE was set

commit 8b328f8002bcf29ef517ee4bf234e09aabec4d2e upstream.

When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.

Cc: stable@vger.kernel.org
Signed-off-by: Puma Hsu <pumahsu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: gadget: Let the interrupt handler disable bottom halves.

commit 84918a89d6efaff075de570b55642b6f4ceeac6d upstream.

The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.

Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.

Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.

Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e7b0 ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: pci: Fix Bay Trail phy GPIO mappings

commit 62e3f0afe246720f7646eb1b034a6897dac34405 upstream.

When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.

Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.

Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: pci: Add "snps,dis_u2_susphy_quirk" for Intel Bay Trail

commit d7c93a903f33ff35aa0e6b5a8032eb9755b00826 upstream.

Commit e0082698b689 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
fixed an issue where ULPI transfers would timeout if any requests where
send to the phy sometime after init, giving it enough time to auto-suspend.

Commit e5f4ca3fce90 ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend
regression") changed the behavior to instead of clearing the
DWC3_GUSB2PHYCFG_SUSPHY bit, add an extra sleep when it is set.

But on Bay Trail devices, when phy_set_mode() gets called during init,
this leads to errors like these:
[   28.451522] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
[   28.464089] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a

Add "snps,dis_u2_susphy_quirk" to the settings for Bay Trail devices to
fix this. This restores the old behavior for Bay Trail devices, since
previously the DWC3_GUSB2PHYCFG_SUSPHY bit would get cleared on the first
ulpi_read/_write() and then was never set again.

Fixes: e5f4ca3fce90 ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Cc: stable@kernel.org
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc2: drd: fix soft connect when gadget is unconfigured

commit 32fde84362c40961726a5c91f35ad37355ccc0c6 upstream.

When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
 new high-speed USB device number ...
 device descriptor read/64, error -110

Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
 - usb_gadget_connect
   - dwc2_hsotg_pullup
     - dwc2_hsotg_core_connect

Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Telit LE910R1 compositions

commit cfc4442c642d568014474b6718ccf65dc7ca6099 upstream.

Add support for the following Telit LE910R1 compositions:

0x701a: rndis, tty, tty, tty
0x701b: ecm, tty, tty, tty
0x9201: tty

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20220218134552.4051-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add support for DW5829e

commit 6ecb3f0b18b320320460a42e40d6fb603f6ded96 upstream.

Dell DW5829e same as DW5821e except CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
There are 2 types product of DW5829e: normal and eSIM.
So we will add 2 PID for DW5829e.
And for each PID, it support MBIM or RMNET.
Let's see test evidence as below:

DW5829e MBIM mode:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  4 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  2
P:  Vendor=413c ProdID=81e6 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#=0x6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

DW5829e RMNET mode:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  5 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=413c ProdID=81e6 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

DW5829e-eSIM MBIM mode:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  6 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  2
P:  Vendor=413c ProdID=81e4 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#=0x6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

DW5829e-eSIM RMNET mode:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  7 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=413c ProdID=81e4 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

BTW, the interface 0x6 of MBIM mode is GNSS port, which not same as NMEA
port. So it's banned from serial option driver.
The remaining interfaces 0x2-0x5 are: MODEM, MODEM, NMEA, DIAG.

Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20220214021401.6264-1-slark_xiao@163.com
[ johan: drop unnecessary reservation of interface 1 ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracefs: Set the group ownership in apply_options() not parse_options()

commit 851e99ebeec3f4a672bb5010cf1ece095acee447 upstream.

Al Viro brought it to my attention that the dentries may not be filled
when the parse_options() is called, causing the call to set_gid() to
possibly crash. It should only be called if parse_options() succeeds
totally anyway.

He suggested the logical place to do the update is in apply_options().

Link: https://lore.kernel.org/all/20220225165219.737025658@goodmis.org/
Link: https://lkml.kernel.org/r/20220225153426.1c4cab6b@gandalf.local.home
Cc: stable@vger.kernel.org
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 48b27b6b5191 ("tracefs: Set all files to the same group ownership as the mount option")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: gadget: validate endpoint index for xilinx udc

commit 7f14c7227f342d9932f9b918893c8814f86d2a0d upstream.

Assure that host may not manipulate the index to point
past endpoint array.

Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: rndis: add spinlock for rndis response list

commit aaaba1c86d04dac8e49bf508b492f81506257da3 upstream.

There's no lock for rndis response list. It could cause list corruption
if there're two different list_add at the same time like below.
It's better to add in rndis_add_response / rndis_free_response
/ rndis_get_next_response to prevent any race condition on response list.

[  361.894299] [1:   irq/191-dwc3:16979] list_add corruption.
next->prev should be prev (ffffff80651764d0),
but was ffffff883dc36f80. (next=ffffff80651764d0).

[  361.904380] [1:   irq/191-dwc3:16979] Call trace:
[  361.904391] [1:   irq/191-dwc3:16979]  __list_add_valid+0x74/0x90
[  361.904401] [1:   irq/191-dwc3:16979]  rndis_msg_parser+0x168/0x8c0
[  361.904409] [1:   irq/191-dwc3:16979]  rndis_command_complete+0x24/0x84
[  361.904417] [1:   irq/191-dwc3:16979]  usb_gadget_giveback_request+0x20/0xe4
[  361.904426] [1:   irq/191-dwc3:16979]  dwc3_gadget_giveback+0x44/0x60
[  361.904434] [1:   irq/191-dwc3:16979]  dwc3_ep0_complete_data+0x1e8/0x3a0
[  361.904442] [1:   irq/191-dwc3:16979]  dwc3_ep0_interrupt+0x29c/0x3dc
[  361.904450] [1:   irq/191-dwc3:16979]  dwc3_process_event_entry+0x78/0x6cc
[  361.904457] [1:   irq/191-dwc3:16979]  dwc3_process_event_buf+0xa0/0x1ec
[  361.904465] [1:   irq/191-dwc3:16979]  dwc3_thread_interrupt+0x34/0x5c

Fixes: f6281af9d62e ("usb: gadget: rndis: use list_for_each_entry_safe")
Cc: stable <stable@kernel.org>
Signed-off-by: Daehwan Jung <dh10.jung@samsung.com>
Link: https://lore.kernel.org/r/1645507768-77687-1-git-send-email-dh10.jung@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "USB: serial: ch341: add new Product ID for CH341A"

commit 198a7ebd5fa17b4d0be8cb70240ee1be885175c0 upstream.

This reverts commit 46ee4abb10a07bd8f8ce910ee6b4ae6a947d7f63.

CH341 has Product ID 0x5512 in EPP/MEM mode which is used for
I2C/SPI/GPIO interfaces. In asynchronous serial interface mode
CH341 has PID 0x5523 which is already in the table.

Mode is selected by corresponding jumper setting.

Signed-off-by: Dmytro Bagrii <dimich.dmb@gmail.com>
Link: https://lore.kernel.org/r/20220210164137.4376-1-dimich.dmb@gmail.com
Link: https://lore.kernel.org/r/YJ0OCS/sh+1ifD/q@hovoldconsulting.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ata: pata_hpt37x: disable primary channel on HPT371

commit 8d093e02e898b24c58788b0289e3202317a96d2a upstream.

The HPT371 chip physically has only one channel, the secondary one,
however the primary channel registers do exist! Thus we have to
manually disable the non-existing channel if the BIOS hasn't done this
already. Similarly to the pata_hpt3x2n driver, always disable the
primary channel.

Fixes: 669a5db411d8 ("[libata] Add a bunch of PATA drivers.")
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sc16is7xx: Fix for incorrect data being transmitted

commit eebb0f4e894f1e9577a56b337693d1051dd6ebfd upstream.

UART drivers are meant to use the port spinlock within certain
methods, to protect against reentrancy. The sc16is7xx driver does
very little locking, presumably because when added it triggers
"scheduling while atomic" errors. This is due to the use of mutexes
within the regmap abstraction layer, and the mutex implementation's
habit of sleeping the current thread while waiting for access.
Unfortunately this lack of interlocking can lead to corruption of
outbound data, which occurs when the buffer used for I2C transmission
is used simultaneously by two threads - a work queue thread running
sc16is7xx_tx_proc, and an IRQ thread in sc16is7xx_port_irq, both
of which can call sc16is7xx_handle_tx.

An earlier patch added efr_lock, a mutex that controls access to the
EFR register. This mutex is already claimed in the IRQ handler, and
all that is required is to claim the same mutex in sc16is7xx_tx_proc.

See: https://github.com/raspberrypi/linux/issues/4885

Fixes: 6393ff1c4435 ("sc16is7xx: Use threaded IRQ")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20220216160802.1026013-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: Fix error handling for PM

commit 632fe0bb8c5b9c06ec961f575ee42a6fff5eceeb upstream.

The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). In the PM Runtime docs:
    Drivers in ->remove() callback should undo the runtime PM changes done
    in ->probe(). Usually this means calling pm_runtime_disable(),
    pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.

Fix this problem for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553.

Fixes: 7d0ead5c3f00 ("iio: Reconcile operation order between iio_register/unregister and pm functions")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220106112309.16879-1-linmq006@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot

commit ea85bf906466191b58532bb19f4fbb4591f0a77e upstream.

We need to wait for sensor settling time (~ 3/ODR) before reading data
in st_lsm6dsx_read_oneshot routine in order to avoid corrupted samples.

Fixes: 290a6ce11d93 ("iio: imu: add support to lsm6dsx driver")
Reported-by: Mario Tesi <mario.tesi@st.com>
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/b41ebda5535895298716c76d939f9f165fcd2d13.1644098120.git.lorenzo@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: accel: fxls8962af: add padding to regmap for SPI

commit ccbed9d8d2a5351d8238f2d3f0741c9a3176f752 upstream.

Add missing don't care padding between address and
data for SPI transfers

Fixes: a3e0b51884ee ("iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20211220125144.3630539-1-sean@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits

commit 0e33d15f1dce9e3a80a970ea7f0b27837168aeca upstream.

According to page 90 of the datasheet [1], AIN_BUFP is bit 6 and
AIN_BUFM is bit 5 of the CONFIG_0 -> CONFIG_7 registers.

Fix the mask used for setting these bits.

[1]: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7124-8.pdf

Fixes: 0eaecea6e487 ("iio: adc: ad7124: Add buffered input support")
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220112200036.694490-1-cosmin.tanislav@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: tsc2046: fix memory corruption by preventing array overflow

commit b7a78a8adaa8849c02f174d707aead0f85dca0da upstream.

On one side we have indio_dev->num_channels includes all physical channels +
timestamp channel. On other side we have an array allocated only for
physical channels. So, fix memory corruption by ARRAY_SIZE() instead of
num_channels variable.

Note the first case is a cleanup rather than a fix as the software
timestamp channel bit in active_scanmask is never set by the IIO core.

Fixes: 9374e8f5a38d ("iio: adc: add ADC driver for the TI TSC2046 controller")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220107081401.2816357-1-o.rempel@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: men_z188_adc: Fix a resource leak in an error handling path

commit e0a2e37f303828d030a83f33ffe14b36cb88d563 upstream.

If iio_device_register() fails, a previous ioremap() is left unbalanced.

Update the error handling path and add the missing iounmap() call, as
already done in the remove function.

Fixes: 74aeac4da66f ("iio: adc: Add MEN 16z188 ADC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/320fc777863880247c2aff4a9d1a54ba69abf080.1643445149.git.christophe.jaillet@wanadoo.fr
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio:imu:adis16480: fix buffering for devices with no burst mode

commit b0e85f95e30d4d2dc22ea123a30dba36406879a1 upstream.

The trigger handler defined in the driver assumes that burst mode is
being used. Hence, for devices that do not support it, we have to use
the adis library default trigger implementation.

Tested-by: Julia Pineda <julia.pineda@analog.com>
Fixes: 941f130881fa9 ("iio: adis16480: support burst read function")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220114132608.241-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Have traceon and traceoff trigger honor the instance

commit 302e9edd54985f584cfc180098f3554774126969 upstream.

If a trigger is set on an event to disable or enable tracing within an
instance, then tracing should be disabled or enabled in the instance and
not at the top level, which is confusing to users.

Link: https://lkml.kernel.org/r/20220223223837.14f94ec3@rorschach.local.home
Cc: stable@vger.kernel.org
Fixes: ae63b31e4d0e2 ("tracing: Separate out trace events from global variables")
Tested-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Dump stacktrace trigger to the corresponding instance

commit ce33c845b030c9cf768370c951bc699470b09fa7 upstream.

The stacktrace event trigger is not dumping the stacktrace to the instance
where it was enabled, but to the global "instance."

Use the private_data, pointing to the trigger file, to figure out the
corresponding trace instance, and use it in the trigger action, like
snapshot_trigger does.

Link: https://lkml.kernel.org/r/afbb0b4f18ba92c276865bc97204d438473f4ebc.1645396236.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Fixes: ae63b31e4d0e2 ("tracing: Separate out trace events from global variables")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Tested-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/ib_srp: Fix a deadlock

[ Upstream commit 081bdc9fe05bb23248f5effb6f811da3da4b8252 ]

Remove the flush_workqueue(system_long_wq) call since flushing
system_long_wq is deadlock-prone and since that call is redundant with a
preceding cancel_work_sync()

Link: https://lore.kernel.org/r/20220215210511.28303-3-bvanassche@acm.org
Fixes: ef6c49d87c34 ("IB/srp: Eliminate state SRP_TARGET_DEAD")
Reported-by: syzbot+831661966588c802aae9@syzkaller.appspotmail.com
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

configfs: fix a race in configfs_{,un}register_subsystem()

[ Upstream commit 84ec758fb2daa236026506868c8796b0500c047d ]

When configfs_register_subsystem() or configfs_unregister_subsystem()
is executing link_group() or unlink_group(),
it is possible that two processes add or delete list concurrently.
Some unfortunate interleavings of them can cause kernel panic.

One of cases is:
A --> B --> C --> D
A <-- B <-- C <-- D

     delete list_head *B        |      delete list_head *C
--------------------------------|-----------------------------------
configfs_unregister_subsystem   |   configfs_unregister_subsystem
  unlink_group                  |     unlink_group
    unlink_obj                  |       unlink_obj
      list_del_init             |         list_del_init
        __list_del_entry        |           __list_del_entry
          __list_del            |             __list_del
            // next == C        |
            next->prev = prev   |
                                |               next->prev = prev
            prev->next = next   |
                                |                 // prev == B
                                |                 prev->next = next

Fix this by adding mutex when calling link_group() or unlink_group(),
but parent configfs_subsystem is NULL when config_item is root.
So I create a mutex configfs_subsystem_mutex.

Fixes: 7063fbf22611 ("[PATCH] configfs: User-driven configuration filesystem")
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: Increase firmware message response DMA wait time

[ Upstream commit b891106da52b2c12dbaf73400f6d225b06a38d80 ]

When polling for the firmware message response, we first poll for the
response message header.  Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion.  Normally, this poll time for DMA completion
is extremely short (0 to a few usec).  But on some devices under some
rare conditions, it can be up to about 20 msec.

Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.

Also, change the error message to include the above delay time when
printing the timeout value.

Fixes: 3c8c20db769c ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-clt: Move free_permit from free_clt to rtrs_clt_close

[ Upstream commit c46fa8911b17e3f808679061a8af8bee219f4602 ]

Error path of rtrs_clt_open() calls free_clt(), where free_permit is
called.  This is wrong since error path of rtrs_clt_open() does not need
to call free_permit().

Also, moving free_permits() call to rtrs_clt_close(), makes it more
aligned with the call to alloc_permit() in rtrs_clt_open().

Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20220217030929.323849-2-haris.iqbal@ionos.com
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-clt: Fix possible double free in error case

[ Upstream commit 8700af2cc18c919b2a83e74e0479038fd113c15d ]

Callback function rtrs_clt_dev_release() for put_device() calls kfree(clt)
to free memory. We shouldn't call kfree(clt) again, and we can't use the
clt after kfree too.

Replace device_register() with device_initialize() and device_add() so that
dev_set_name can() be used appropriately.

Move mutex_destroy() to the release function so it can be called in
the alloc_clt err path.

Fixes: eab098246625 ("RDMA/rtrs-clt: Refactor the failure cases in alloc_clt")
Link: https://lore.kernel.org/r/20220217030929.323849-1-haris.iqbal@ionos.com
Reported-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net-timestamp: convert sk->sk_tskey to atomic_t

[ Upstream commit a1cdec57e03a1352e92fbbe7974039dda4efcec0 ]

UDP sendmsg() can be lockless, this is causing all kinds
of data races.

This patch converts sk->sk_tskey to remove one of these races.

BUG: KCSAN: data-race in __ip_append_data / __ip_append_data

read to 0xffff8881035d4b6c of 4 bytes by task 8877 on cpu 1:
 __ip_append_data+0x1c1/0x1de0 net/ipv4/ip_output.c:994
 ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
 udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

write to 0xffff8881035d4b6c of 4 bytes by task 8880 on cpu 0:
 __ip_append_data+0x1d8/0x1de0 net/ipv4/ip_output.c:994
 ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
 udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x0000054d -> 0x0000054e

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8880 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00167-gdcb85f85fa6f-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 09c2d251b707 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regmap-irq: Update interrupt clear register for proper reset

[ Upstream commit d04ad245d67a3991dfea5e108e4c452c2ab39bac ]

With the existing logic where clear_ack is true (HW doesn’t support
auto clear for ICR), interrupt clear register reset is not handled
properly. Due to this only the first interrupts get processed properly
and further interrupts are blocked due to not resetting interrupt
clear register.

Example for issue case where Invert_ack is false and clear_ack is true:

    Say Default ISR=0x00 & ICR=0x00 and ISR is triggered with 2
    interrupts making ISR = 0x11.

    Step 1: Say ISR is set 0x11 (store status_buff = ISR). ISR needs to
            be cleared with the help of ICR once the Interrupt is processed.

    Step 2: Write ICR = 0x11 (status_buff), this will clear the ISR to 0x00.

    Step 3: Issue - In the existing code, ICR is written with ICR =
            ~(status_buff) i.e ICR = 0xEE -> This will block all the interrupts
            from raising except for interrupts 0 and 4. So expectation here is to
            reset ICR, which will unblock all the interrupts.

            if (chip->clear_ack) {
                 if (chip->ack_invert && !ret)
                  ........
                 else if (!ret)
                     ret = regmap_write(map, reg,
                            ~data->status_buf[i]);

So writing 0 and 0xff (when ack_invert is true) should have no effect, other
than clearing the ACKs just set.

Fixes: 3a6f0fb7b8eb ("regmap: irq: Add support to clear ack registers")
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220217085007.30218-1-quic_pkumpatl@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: rockchip: Reset int_bothedge when changing trigger

[ Upstream commit 7920af5c826cb4a7ada1ae26fdd317642805adc2 ]

With v2 hardware, an IRQ can be configured to trigger on both edges via
a bit in the int_bothedge register. Currently, the driver sets this bit
when changing the trigger type to IRQ_TYPE_EDGE_BOTH, but fails to reset
this bit if the trigger type is later changed to something else. This
causes spurious IRQs, and when using gpio-keys with wakeup-event-action
set to EV_ACT_(DE)ASSERTED, those IRQs translate into spurious wakeups.

Fixes: 3bcbd1a85b68 ("gpio/rockchip: support next version gpio controller")
Reported-by: Guillaume Savaton <guillaume@baierouge.fr>
Tested-by: Guillaume Savaton <guillaume@baierouge.fr>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: spi-zynq-qspi: Fix a NULL pointer dereference in zynq_qspi_exec_mem_op()

[ Upstream commit ab3824427b848da10e9fe2727f035bbeecae6ff4 ]

In zynq_qspi_exec_mem_op(), kzalloc() is directly used in memset(),
which could lead to a NULL pointer dereference on failure of
kzalloc().

Fix this bug by adding a check of tmpbuf.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_SPI_ZYNQ_QSPI=m show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130172253.203700-1-zhou1615@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: Update log_max_qp value to be 17 at most

commit 7f839965b2d77e1926ad08b23c51d60988f10a99 upstream.

Currently, log_max_qp value is dependent on what FW reports as its max capability.
In reality, due to a bug, some FWs report a value greater than 17, even though they
don't support log_max_qp > 17.

This FW issue led the driver to exhaust memory on startup.
Thus, log_max_qp value is set to be no more than 17 regardless
of what FW reports, as it was before the cited commit.

Fixes: f79a609ea6bf ("net/mlx5: Update log_max_qp value to FW max capability")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets

commit 7eaf1f37b8817c608c4e959d69986ef459d345cd upstream.

For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.

Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.

Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.

Fixes: 1182f3659357 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: MPLSoUDP decap, fix check for unsupported matches

commit fdc18e4e4bded2a08638cdcd22dc087a64b9ddad upstream.

Currently offload of rule on bareudp device require tunnel key
in order to match on mpls fields and without it the mpls fields
are ignored, this is incorrect due to the fact udp tunnel doesn't
have key to match on.

Fix by returning error in case flow is matching on tunnel key.

Fixes: 72046a91d134 ("net/mlx5e: Allow to match on mpls parameters")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: DR, Fix the threshold that defines when pool sync is initiated

commit ecd9c5cd46e013659e2fad433057bad1ba66888e upstream.

When deciding whether to start syncing and actually free all the "hot"
ICM chunks, we need to consider the type of the ICM chunks that we're
dealing with. For instance, the amount of available ICM for MODIFY_ACTION
is significantly lower than the usual STE ICM, so the threshold should
account for that - otherwise we can deplete MODIFY_ACTION memory just by
creating and deleting the same modify header action in a continuous loop.

This patch replaces the hard-coded threshold with a dynamic value.

Fixes: 1c58651412bb ("net/mlx5: DR, ICM memory pools sync optimization")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Fix wrong limitation of metadata match on ecpf

commit 07666c75ad17d7389b18ac0235c8cf41e1504ea8 upstream.

Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.

Fixes: 92ab1eb392c6 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Fix possible deadlock on rule deletion

commit b645e57debca846f51b3209907546ea857ddd3f5 upstream.

Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.

Fixes: 465e7baab6d9 ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: DR, Don't allow match on IP w/o matching on full ethertype/ip_version

commit ffb0753b954763d94f52c901adfe58ed0d4005e6 upstream.

Currently SMFS allows adding rule with matching on src/dst IP w/o matching
on full ethertype or ip_version, which is not supported by HW.
This patch fixes this issue and adds the check as it is done in DMFS.

Fixes: 26d688e33f88 ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmvnic: schedule failover only if vioctl fails

commit 277f2bb14361790a70e4b3c649e794b75a91a597 upstream.

If client is unable to initiate a failover reset via H_VIOCTL hcall, then
it should schedule a failover reset as a last resort. Otherwise, there is
no need to do a last resort.

Fixes: 334c42414729 ("ibmvnic: improve failover sysfs entry")
Reported-by: Cris Forno <cforno12@outlook.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221210545.115283-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: DR, Cache STE shadow memory

commit e5b2bc30c21139ae10f0e56989389d0bc7b7b1d6 upstream.

During rule insertion on each ICM memory chunk we also allocate shadow memory
used for management. This includes the hw_ste, dr_ste and miss list per entry.
Since the scale of these allocations is large we noticed a performance hiccup
that happens once malloc and free are stressed.
In extreme usecases when ~1M chunks are freed at once, it might take up to 40
seconds to complete this, up to the point the kernel sees this as self-detected
stall on CPU:

 rcu: INFO: rcu_sched self-detected stall on CPU

To resolve this we will increase the reuse of shadow memory.
Doing this we see that a time in the aforementioned usecase dropped from ~40
seconds to ~8-10 seconds.

Fixes: 29cf8febd185 ("net/mlx5: DR, ICM pool memory allocator")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udp_tunnel: Fix end of loop test in udp_tunnel_nic_unregister()

commit de7b2efacf4e83954aed3f029d347dfc0b7a4f49 upstream.

This test is checking if we exited the list via break or not.  However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct.  It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.

Fixes: 74cc6d182d03 ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

surface: surface3_power: Fix battery readings on batteries without a serial number

commit 21d90aaee8d5c2a097ef41f1430d97661233ecc6 upstream.

The battery on the 2nd hand Surface 3 which I recently bought appears to
not have a serial number programmed in. This results in any I2C reads from
the registers containing the serial number failing with an I2C NACK.

This was causing mshw0011_bix() to fail causing the battery readings to
not work at all.

Ignore EREMOTEIO (I2C NACK) errors when retrieving the serial number and
continue with an empty serial number to fix this.

Fixes: b1f81b496b0d ("platform/x86: surface3_power: MSHW0011 rev-eng implementation")
BugLink: https://github.com/linux-surface/linux-surface/issues/608
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220224101848.7219-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: Use a mutex for locking "struct smc_pnettable"

commit 7ff57e98fb78ad94edafbdc7435f2d745e9e6bb5 upstream.

smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).

read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.

Fix this bug by replacing the rwlock with a mutex.

Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes: 64e28b52c7a6 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_tables: fix memory leak during stateful obj update

commit dad3bdeef45f81a6e90204bcc85360bb76eccec7 upstream.

stateful objects can be updated from the control plane.
The transaction logic allocates a temporary object for this purpose.

The ->init function was called for this object, so plain kfree() leaks
resources. We must call ->destroy function of the object.

nft_obj_destroy does this, but it also decrements the module refcount,
but the update path doesn't increment it.

To avoid special-casing the update object release, do module_get for
the update case too and release it via nft_obj_destroy().

Fixes: d62d0ba97b58 ("netfilter: nf_tables: Introduce stateful object update operation")
Cc: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mdio-ipq4019: add delay after clock enable

commit b6ad6261d27708567b309fdb3102b12c42a070cc upstream.

Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.

PHY detect failure started to show after commit 7590fc6f80ac ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.

10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.

Fixes: 23a890d493e3 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfp: flower: Fix a potential leak in nfp_tunnel_add_shared_mac()

commit 3a14d0888eb4b0045884126acc69abfb7b87814d upstream.

ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.

In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.

So set it to -1.

Fixes: 20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_tables: unregister flowtable hooks on netns exit

commit 6069da443bf65f513bb507bb21e2f87cfb1ad0b6 upstream.

Unregister flowtable hooks before they are releases via
nf_tables_flowtable_destroy() otherwise hook core reports UAF.

BUG: KASAN: use-after-free in nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
Read of size 4 at addr ffff8880736f7438 by task syz-executor579/3666

CPU: 0 PID: 3666 Comm: syz-executor579 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 __dump_stack lib/dump_stack.c:88 [inline] lib/dump_stack.c:106
 dump_stack_lvl+0x1dc/0x2d8 lib/dump_stack.c:106 lib/dump_stack.c:106
 print_address_description+0x65/0x380 mm/kasan/report.c:247 mm/kasan/report.c:247
 __kasan_report mm/kasan/report.c:433 [inline]
 __kasan_report mm/kasan/report.c:433 [inline] mm/kasan/report.c:450
 kasan_report+0x19a/0x1f0 mm/kasan/report.c:450 mm/kasan/report.c:450
 nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
 __nf_register_net_hook+0x27e/0x8d0 net/netfilter/core.c:429 net/netfilter/core.c:429
 nf_register_net_hook+0xaa/0x180 net/netfilter/core.c:571 net/netfilter/core.c:571
 nft_register_flowtable_net_hooks+0x3c5/0x730 net/netfilter/nf_tables_api.c:7232 net/netfilter/nf_tables_api.c:7232
 nf_tables_newflowtable+0x2022/0x2cf0 net/netfilter/nf_tables_api.c:7430 net/netfilter/nf_tables_api.c:7430
 nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline]
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
 nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline] net/netfilter/nfnetlink.c:652
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] net/netfilter/nfnetlink.c:652
 nfnetlink_rcv+0x10e6/0x2550 net/netfilter/nfnetlink.c:652 net/netfilter/nfnetlink.c:652

__nft_release_hook() calls nft_unregister_flowtable_net_hooks() which
only unregisters the hooks, then after RCU grace period, it is
guaranteed that no packets add new entries to the flowtable (no flow
offload rules and flowtable hooks are reachable from packet path), so it
is safe to call nf_flow_table_free() which cleans up the remaining
entries from the flowtable (both software and hardware) and it unbinds
the flow_block.

Fixes: ff4bf2f42a40 ("netfilter: nf_tables: add nft_unregister_flowtable_hook()")
Reported-by: syzbot+e918523f77e62790d6d9@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Force inlining of checksum functions in net/checksum.h

commit 5486f5bf790b5c664913076c3194b8f916a5c7ad upstream.

All functions defined as static inline in net/checksum.h are
meant to be inlined for performance reason.

But since commit ac7c3e4ff401 ("compiler: enable
CONFIG_OPTIMIZE_INLINING forcibly") the compiler is allowed to
uninline functions when it wants.

Fair enough in the general case, but for tiny performance critical
checksum helpers that's counter-productive.

The problem mainly arises when selecting CONFIG_CC_OPTIMISE_FOR_SIZE,
Those helpers being 'static inline' in header files you suddenly find
them duplicated many times in the resulting vmlinux.

Here is a typical exemple when building powerpc pmac32_defconfig
with CONFIG_CC_OPTIMISE_FOR_SIZE. csum_sub() appears 4 times:

c04a23cc <csum_sub>:
c04a23cc: 7c 84 20 f8  not     r4,r4
c04a23d0: 7c 63 20 14  addc    r3,r3,r4
c04a23d4: 7c 63 01 94  addze   r3,r3
c04a23d8: 4e 80 00 20  blr
...
c04a2ce8: 4b ff f6 e5  bl      c04a23cc <csum_sub>
...
c04a2d2c: 4b ff f6 a1  bl      c04a23cc <csum_sub>
...
c04a2d54: 4b ff f6 79  bl      c04a23cc <csum_sub>
...
c04a754c <csum_sub>:
c04a754c: 7c 84 20 f8  not     r4,r4
c04a7550: 7c 63 20 14  addc    r3,r3,r4
c04a7554: 7c 63 01 94  addze   r3,r3
c04a7558: 4e 80 00 20  blr
...
c04ac930: 4b ff ac 1d  bl      c04a754c <csum_sub>
...
c04ad264: 4b ff a2 e9  bl      c04a754c <csum_sub>
...
c04e3b08 <csum_sub>:
c04e3b08: 7c 84 20 f8  not     r4,r4
c04e3b0c: 7c 63 20 14  addc    r3,r3,r4
c04e3b10: 7c 63 01 94  addze   r3,r3
c04e3b14: 4e 80 00 20  blr
...
c04e5788: 4b ff e3 81  bl      c04e3b08 <csum_sub>
...
c04e65c8: 4b ff d5 41  bl      c04e3b08 <csum_sub>
...
c0512d34 <csum_sub>:
c0512d34: 7c 84 20 f8  not     r4,r4
c0512d38: 7c 63 20 14  addc    r3,r3,r4
c0512d3c: 7c 63 01 94  addze   r3,r3
c0512d40: 4e 80 00 20  blr
...
c0512dfc: 4b ff ff 39  bl      c0512d34 <csum_sub>
...
c05138bc: 4b ff f4 79  bl      c0512d34 <csum_sub>
...

Restore the expected behaviour by using __always_inline for all
functions defined in net/checksum.h

vmlinux size is even reduced by 256 bytes with this patch:

   text    data     bss     dec     hex filename
6980022 2515362  194384 9689768  93daa8 vmlinux.before
6979862 2515266  194384 9689512  93d9a8 vmlinux.now

Fixes: ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ll_temac: check the return value of devm_kmalloc()

commit b352c3465bb808ab700d03f5bac2f7a6f37c5350 upstream.

devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.

Fixes: f14f5c11f051 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: act_ct: Fix flow table lookup after ct clear or switching zones

commit 2f131de361f6d0eaff17db26efdb844c178432f8 upstream.

Flow table lookup is skipped if packet either went through ct clear
action (which set the IP_CT_UNTRACKED flag on the packet), or while
switching zones and there is already a connection associated with
the packet. This will result in no SW offload of the connection,
and the and connection not being removed from flow table with
TCP teardown (fin/rst packet).

To fix the above, remove these unneccary checks in flow
table lookup.

Fixes: 46475bb20f4b ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/dg2: Print PHY name properly on calibration error

commit 28adef861233c6fce47372ebd2070b55eaa8e899 upstream.

We need to use phy_name() to convert the PHY value into a human-readable
character in the error message.

Fixes: a6a128116e55 ("drm/i915/dg2: Wait for SNPS PHY calibration during display init")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220215163545.2175730-1-matthew.d.roper@intel.com
(cherry picked from commit 84073e568eec7b586b2f6fd5fb2fb08f59edec54)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vc4: crtc: Fix runtime_pm reference counting

commit 6764eb690e77ecded48587d6d4e346ba2e196546 upstream.

At boot on the BCM2711, if the HDMI controllers are running, the CRTC
driver will disable itself and its associated HDMI controller to work
around a hardware bug that would leave some pixels stuck in a FIFO.

In order to avoid that issue, we need to run some operations in lockstep
between the CRTC and HDMI controller, and we need to make sure the HDMI
controller will be powered properly.

However, since we haven't enabled it through KMS, the runtime_pm state
is off at this point so we need to make sure the device is powered
through pm_runtime_resume_and_get, and once the operations are complete,
we call pm_runtime_put.

However, the HDMI controller will do that itself in its
post_crtc_powerdown, which means we'll end up calling pm_runtime_put for
a single pm_runtime_get, throwing the reference counting off. Let's
remove the pm_runtime_put call in the CRTC code in order to have the
proper counting.

Fixes: bca10db67bda ("drm/vc4: crtc: Make sure the HDMI controller is powered when disabling")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203102003.1114673-1-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Fix wrong return value on ioctl EEPROM query failure

commit 0b89429722353d112f8b8b29ca397e95fa994d27 upstream.

The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.

Fixes: bb64143eee8c ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/edid: Always set RGB444

commit ecbd4912a693b862e25cba0a6990a8c95b00721e upstream.

In order to fill the drm_display_info structure each time an EDID is
read, the code currently will call drm_add_display_info with the parsed
EDID.

drm_add_display_info will then call drm_reset_display_info to reset all
the fields to 0, and then set them to the proper value depending on the
EDID.

In the color_formats case, we will thus report that we don't support any
color format, and then fill it back with RGB444 plus the additional
formats described in the EDID Feature Support byte.

However, since that byte only contains format-related bits since the 1.4
specification, this doesn't happen if the EDID is following an earlier
specification. In turn, it means that for one of these EDID, we end up
with color_formats set to 0.

The EDID 1.3 specification never really specifies what it means by RGB
exactly, but since both HDMI and DVI will use RGB444, it's fairly safe
to assume it's supposed to be RGB444.

Let's move the addition of RGB444 to color_formats earlier in
drm_add_display_info() so that it's always set for a digital display.

Fixes: da05a5a71ad8 ("drm: parse color format support for digital displays")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203115416.1137308-1-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

openvswitch: Fix setting ipv6 fields causing hw csum failure

commit d9b5ae5c1b241b91480aa30408be12fe91af834a upstream.

Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.

Fix this by updating skb->csum if available.

Trace resulted by ipv6 ttl dec and then sending packet
to conntrack [actions: set(ipv6(hlimit=63)),ct(zone=99)]:
[295241.900063] s_pf0vf2: hw csum failure
[295241.923191] Call Trace:
[295241.925728]  <IRQ>
[295241.927836]  dump_stack+0x5c/0x80
[295241.931240]  __skb_checksum_complete+0xac/0xc0
[295241.935778]  nf_conntrack_tcp_packet+0x398/0xba0 [nf_conntrack]
[295241.953030]  nf_conntrack_in+0x498/0x5e0 [nf_conntrack]
[295241.958344]  __ovs_ct_lookup+0xac/0x860 [openvswitch]
[295241.968532]  ovs_ct_execute+0x4a7/0x7c0 [openvswitch]
[295241.979167]  do_execute_actions+0x54a/0xaa0 [openvswitch]
[295242.001482]  ovs_execute_actions+0x48/0x100 [openvswitch]
[295242.006966]  ovs_dp_process_packet+0x96/0x1d0 [openvswitch]
[295242.012626]  ovs_vport_receive+0x6c/0xc0 [openvswitch]
[295242.028763]  netdev_frame_hook+0xc0/0x180 [openvswitch]
[295242.034074]  __netif_receive_skb_core+0x2ca/0xcb0
[295242.047498]  netif_receive_skb_internal+0x3e/0xc0
[295242.052291]  napi_gro_receive+0xba/0xe0
[295242.056231]  mlx5e_handle_rx_cqe_mpwrq_rep+0x12b/0x250 [mlx5_core]
[295242.062513]  mlx5e_poll_rx_cq+0xa0f/0xa30 [mlx5_core]
[295242.067669]  mlx5e_napi_poll+0xe1/0x6b0 [mlx5_core]
[295242.077958]  net_rx_action+0x149/0x3b0
[295242.086762]  __do_softirq+0xd7/0x2d6
[295242.090427]  irq_exit+0xf7/0x100
[295242.093748]  do_IRQ+0x7f/0xd0
[295242.096806]  common_interrupt+0xf/0xf
[295242.100559]  </IRQ>
[295242.102750] RIP: 0033:0x7f9022e88cbd
[295242.125246] RSP: 002b:00007f9022282b20 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffda
[295242.132900] RAX: 0000000000000005 RBX: 0000000000000010 RCX: 0000000000000000
[295242.140120] RDX: 00007f9022282ba8 RSI: 00007f9022282a30 RDI: 00007f9014005c30
[295242.147337] RBP: 00007f9014014d60 R08: 0000000000000020 R09: 00007f90254a8340
[295242.154557] R10: 00007f9022282a28 R11: 0000000000000246 R12: 0000000000000000
[295242.161775] R13: 00007f902308c000 R14: 000000000000002b R15: 00007f9022b71f40

Fixes: 3fdbd1ce11e5 ("openvswitch: add ipv6 'set' action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Link: https://lore.kernel.org/r/20220223163416.24096-1-paulb@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mv643xx_eth: process retval from of_get_mac_address

commit 42404d8f1c01861b22ccfa1d70f950242720ae57 upstream.

Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.

It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.

Fixes: 76723bca2802 ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gso: do not skip outer ip header in case of ipip and net_failover

commit cc20cced0598d9a5ff91ae4ab147b3b5e99ee819 upstream.

We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
 -> ipip encap -> net_failover tx -> virtio_net tx

When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.

Call Trace:
 tcp4_gso_segment        ------> return NULL
 inet_gso_segment        ------> inner iph, network_header points to
 ipip_gso_segment
 inet_gso_segment        ------> outer iph
 skb_mac_gso_segment

Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.

Call Trace:
 inet_gso_segment        ------> inner iph, outer iph is skipped
 skb_mac_gso_segment
 __skb_gso_segment
 validate_xmit_skb
 validate_xmit_skb_list
 sch_direct_xmit
 __qdisc_run
 __dev_queue_xmit        ------> virtio_net
 dev_hard_start_xmit
 __dev_queue_xmit        ------> net_failover
 ip_finish_output2
 ip_output
 iptunnel_xmit
 ip_tunnel_xmit
 ipip_tunnel_xmit        ------> ipip
 dev_hard_start_xmit
 __dev_queue_xmit
 ip_finish_output2
 ip_output
 ip_forward
 ip_rcv
 __netif_receive_skb_one_core
 netif_receive_skb_internal
 napi_gro_receive
 receive_buf
 virtnet_poll
 net_rx_action

The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.

This patch also includes ipv6_gso_segment(), considering SIT, etc.

Fixes: cb32f511a70b ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tipc: Fix end of loop tests for list_for_each_entry()

commit a1f8fec4dac8bc7b172b2bdbd881e015261a6322 upstream.

These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer.  In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {".  That's going to work most of the time,
but there is a potential for those to be equal.

Fixes: 1593123a6a49 ("tipc: add name table dump to new netlink api")
Fixes: 1a1a143daf84 ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info

commit 602e57c9799c19f27e440639deed3ec45cfe1651 upstream.

Commit e7d65803e2bb ("nvme-multipath: revalidate paths during rescan")
introduced the NVME_NS_READY flag, which nvme_path_is_disabled() uses
to check if a path can be used or not.  We also need to set this flag
for devices that fail the ZNS feature validation and which are available
through passthrough devices only to that they can be used in multipathing
setups.

Fixes: e7d65803e2bb ("nvme-multipath: revalidate paths during rescan")
Reported-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor friends

commit ef527f968ae05c6717c39f49c8709a7e2c19183a upstream.

Whenever one of these functions pull all data from an skb in a frag_list,
use consume_skb() instead of kfree_skb() to avoid polluting drop
monitoring.

Fixes: 6fa01ccd8830 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220220154052.1308469-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

io_uring: add a schedule point in io_add_buffers()

commit f240762f88b4b1b58561939ffd44837759756477 upstream.

Looping ~65535 times doing kmalloc() calls can trigger soft lockups,
especially with DEBUG features (like KASAN).

[  253.536212] watchdog: BUG: soft lockup - CPU#64 stuck for 26s! [b219417889:12575]
[  253.544433] Modules linked in: vfat fat i2c_mux_pca954x i2c_mux spidev cdc_acm xhci_pci xhci_hcd sha3_generic gq(O)
[  253.544451] CPU: 64 PID: 12575 Comm: b219417889 Tainted: G S         O      5.17.0-smp-DEV #801
[  253.544457] RIP: 0010:kernel_text_address (./include/asm-generic/sections.h:192 ./include/linux/kallsyms.h:29 kernel/extable.c:67 kernel/extable.c:98)
[  253.544464] Code: 0f 93 c0 48 c7 c1 e0 63 d7 a4 48 39 cb 0f 92 c1 20 c1 0f b6 c1 5b 5d c3 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 53 48 89 fb <48> c7 c0 00 00 80 a0 41 be 01 00 00 00 48 39 c7 72 0c 48 c7 c0 40
[  253.544468] RSP: 0018:ffff8882d8baf4c0 EFLAGS: 00000246
[  253.544471] RAX: 1ffff1105b175e00 RBX: ffffffffa13ef09a RCX: 00000000a13ef001
[  253.544474] RDX: ffffffffa13ef09a RSI: ffff8882d8baf558 RDI: ffffffffa13ef09a
[  253.544476] RBP: ffff8882d8baf4d8 R08: ffff8882d8baf5e0 R09: 0000000000000004
[  253.544479] R10: ffff8882d8baf5e8 R11: ffffffffa0d59a50 R12: ffff8882eab20380
[  253.544481] R13: ffffffffa0d59a50 R14: dffffc0000000000 R15: 1ffff1105b175eb0
[  253.544483] FS:  00000000016d3380(0000) GS:ffff88af48c00000(0000) knlGS:0000000000000000
[  253.544486] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  253.544488] CR2: 00000000004af0f0 CR3: 00000002eabfa004 CR4: 00000000003706e0
[  253.544491] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  253.544492] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  253.544494] Call Trace:
[  253.544496]  <TASK>
[  253.544498] ? io_queue_sqe (fs/io_uring.c:7143)
[  253.544505] __kernel_text_address (kernel/extable.c:78)
[  253.544508] unwind_get_return_address (arch/x86/kernel/unwind_frame.c:19)
[  253.544514] arch_stack_walk (arch/x86/kernel/stacktrace.c:27)
[  253.544517] ? io_queue_sqe (fs/io_uring.c:7143)
[  253.544521] stack_trace_save (kernel/stacktrace.c:123)
[  253.544527] ____kasan_kmalloc (mm/kasan/common.c:39 mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:515)
[  253.544531] ? ____kasan_kmalloc (mm/kasan/common.c:39 mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:515)
[  253.544533] ? __kasan_kmalloc (mm/kasan/common.c:524)
[  253.544535] ? kmem_cache_alloc_trace (./include/linux/kasan.h:270 mm/slab.c:3567)
[  253.544541] ? io_issue_sqe (fs/io_uring.c:4556 fs/io_uring.c:4589 fs/io_uring.c:6828)
[  253.544544] ? __io_queue_sqe (fs/io_uring.c:?)
[  253.544551] __kasan_kmalloc (mm/kasan/common.c:524)
[  253.544553] kmem_cache_alloc_trace (./include/linux/kasan.h:270 mm/slab.c:3567)
[  253.544556] ? io_issue_sqe (fs/io_uring.c:4556 fs/io_uring.c:4589 fs/io_uring.c:6828)
[  253.544560] io_issue_sqe (fs/io_uring.c:4556 fs/io_uring.c:4589 fs/io_uring.c:6828)
[  253.544564] ? __kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
[  253.544567] ? __kasan_slab_alloc (mm/kasan/common.c:39 mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
[  253.544569] ? kmem_cache_alloc_bulk (mm/slab.h:732 mm/slab.c:3546)
[  253.544573] ? __io_alloc_req_refill (fs/io_uring.c:2078)
[  253.544578] ? io_submit_sqes (fs/io_uring.c:7441)
[  253.544581] ? __se_sys_io_uring_enter (fs/io_uring.c:10154 fs/io_uring.c:10096)
[  253.544584] ? __x64_sys_io_uring_enter (fs/io_uring.c:10096)
[  253.544587] ? do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
[  253.544590] ? entry_SYSCALL_64_after_hwframe (??:?)
[  253.544596] __io_queue_sqe (fs/io_uring.c:?)
[  253.544600] io_queue_sqe (fs/io_uring.c:7143)
[  253.544603] io_submit_sqe (fs/io_uring.c:?)
[  253.544608] io_submit_sqes (fs/io_uring.c:?)
[  253.544612] __se_sys_io_uring_enter (fs/io_uring.c:10154 fs/io_uring.c:10096)
[  253.544616] __x64_sys_io_uring_enter (fs/io_uring.c:10096)
[  253.544619] do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80)
[  253.544623] entry_SYSCALL_64_after_hwframe (??:?)

Fixes: ddf0322db79c ("io_uring: add IORING_OP_PROVIDE_BUFFERS")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: io-uring <io-uring@vger.kernel.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220215041003.2394784-1-eric.dumazet@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Add schedule points in batch ops

commit 75134f16e7dd0007aa474b281935c5f42e79f2c8 upstream.

syzbot reported various soft lockups caused by bpf batch operations.

 INFO: task kworker/1:1:27 blocked for more than 140 seconds.
 INFO: task hung in rcu_barrier

Nothing prevents batch ops to process huge amount of data,
we need to add schedule points in them.

Note that maybe_wait_bpf_programs(map) calls from
generic_map_delete_batch() can be factorized by moving
the call after the loop.

This will be done later in -next tree once we get this fix merged,
unless there is strong opinion doing this optimization sooner.

Fixes: aa2e93b8e58e ("bpf: Add generic support for update and delete batch ops")
Fixes: cb4d03ab499d ("bpf: Add generic support for lookup batch op")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/bpf/20220217181902.808742-1-eric.dumazet@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Fix a bpf_timer initialization issue

commit 5eaed6eedbe9612f642ad2b880f961d1c6c8ec2b upstream.

The patch in [1] intends to fix a bpf_timer related issue,
but the fix caused existing 'timer' selftest to fail with
hang or some random errors. After some debug, I found
an issue with check_and_init_map_value() in the hashtab.c.
More specifically, in hashtab.c, we have code
  l_new = bpf_map_kmalloc_node(&htab->map, ...)
  check_and_init_map_value(&htab->map, l_new...)
Note that bpf_map_kmalloc_node() does not do initialization
so l_new contains random value.

The function check_and_init_map_value() intends to zero the
bpf_spin_lock and bpf_timer if they exist in the map.
But I found bpf_spin_lock is zero'ed but bpf_timer is not zero'ed.
With [1], later copy_map_value() skips copying of
bpf_spin_lock and bpf_timer. The non-zero bpf_timer caused
random failures for 'timer' selftest.
Without [1], for both bpf_spin_lock and bpf_timer case,
bpf_timer will be zero'ed, so 'timer' self test is okay.

For check_and_init_map_value(), why bpf_spin_lock is zero'ed
properly while bpf_timer not. In bpf uapi header, we have
  struct bpf_spin_lock {
        __u32   val;
  };
  struct bpf_timer {
        __u64 :64;
        __u64 :64;
  } __attribute__((aligned(8)));

The initialization code:
  *(struct bpf_spin_lock *)(dst + map->spin_lock_off) =
      (struct bpf_spin_lock){};
  *(struct bpf_timer *)(dst + map->timer_off) =
      (struct bpf_timer){};
It appears the compiler has no obligation to initialize anonymous fields.
For example, let us use clang with bpf target as below:
  $ cat t.c
  struct bpf_timer {
        unsigned long long :64;
  };
  struct bpf_timer2 {
        unsigned long long a;
  };

  void test(struct bpf_timer *t) {
    *t = (struct bpf_timer){};
  }
  void test2(struct bpf_timer2 *t) {
    *t = (struct bpf_timer2){};
  }
  $ clang -target bpf -O2 -c -g t.c
  $ llvm-objdump -d t.o
   ...
   0000000000000000 <test>:
       0:       95 00 00 00 00 00 00 00 exit
   0000000000000008 <test2>:
       1:       b7 02 00 00 00 00 00 00 r2 = 0
       2:       7b 21 00 00 00 00 00 00 *(u64 *)(r1 + 0) = r2
       3:       95 00 00 00 00 00 00 00 exit

gcc11.2 does not have the above issue. But from
  INTERNATIONAL STANDARD ©ISO/IEC ISO/IEC 9899:201x
  Programming languages — C
  http://www.open-std.org/Jtc1/sc22/wg14/www/docs/n1547.pdf
  page 157:
  Except where explicitly stated otherwise, for the purposes of
  this subclause unnamed members of objects of structure and union
  type do not participate in initialization. Unnamed members of
  structure objects have indeterminate value even after initialization.

To fix the problem, let use memset for bpf_timer case in
check_and_init_map_value(). For consistency, memset is also
used for bpf_spin_lock case.

  [1] https://lore.kernel.org/bpf/20220209070324.1093182-2-memxor@gmail.com/

Fixes: 68134668c17f3 ("bpf: Add map side support for bpf timers.")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220211194953.3142152-1-yhs@fb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: bpf: Check bpf_msg_push_data return value

commit 61d06f01f9710b327a53492e5add9f972eb909b3 upstream.

bpf_msg_push_data may return a non-zero value to indicate an error. The
return value should be checked to prevent undetected errors.

To indicate an error, the BPF programs now perform a different action
than their intended one to make the userspace test program notice the
error, i.e., the programs supposed to pass/redirect drop, the program
supposed to drop passes.

Fixes: 84fbfe026acaa ("bpf: test_sockmap add options to use msg_push_data")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/89f767bb44005d6b4dd1f42038c438f76b3ebfad.1644601294.git.fmaurer@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Do not try bpf_msg_push_data with len 0

commit 4a11678f683814df82fca9018d964771e02d7e6d upstream.

If bpf_msg_push_data() is called with len 0 (as it happens during
selftests/bpf/test_sockmap), we do not need to do anything and can
return early.

Calling bpf_msg_push_data() with len 0 previously lead to a wrong ENOMEM
error: we later called get_order(copy + len); if len was 0, copy + len
was also often 0 and get_order() returned some undefined value (at the
moment 52). alloc_pages() caught that and failed, but then bpf_msg_push_data()
returned ENOMEM. This was wrong because we are most probably not out of
memory and actually do not need any additional memory.

Fixes: 6fff607e2f14b ("bpf: sk_msg program helper bpf_msg_push_data")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/df69012695c7094ccb1943ca02b4920db3537466.1644421921.git.fmaurer@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Fix crash due to incorrect copy_map_value

commit a8abb0c3dc1e28454851a00f8b7333d9695d566c upstream.

When both bpf_spin_lock and bpf_timer are present in a BPF map value,
copy_map_value needs to skirt both objects when copying a value into and
out of the map. However, the current code does not set both s_off and
t_off in copy_map_value, which leads to a crash when e.g. bpf_spin_lock
is placed in map value with bpf_timer, as bpf_map_update_elem call will
be able to overwrite the other timer object.

When the issue is not fixed, an overwriting can produce the following
splat:

[root@(none) bpf]# ./test_progs -t timer_crash
[   15.930339] bpf_testmod: loading out-of-tree module taints kernel.
[   16.037849] ==================================================================
[   16.038458] BUG: KASAN: user-memory-access in __pv_queued_spin_lock_slowpath+0x32b/0x520
[   16.038944] Write of size 8 at addr 0000000000043ec0 by task test_progs/325
[   16.039399]
[   16.039514] CPU: 0 PID: 325 Comm: test_progs Tainted: G           OE     5.16.0+ #278
[   16.039983] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ArchLinux 1.15.0-1 04/01/2014
[   16.040485] Call Trace:
[   16.040645]  <TASK>
[   16.040805]  dump_stack_lvl+0x59/0x73
[   16.041069]  ? __pv_queued_spin_lock_slowpath+0x32b/0x520
[   16.041427]  kasan_report.cold+0x116/0x11b
[   16.041673]  ? __pv_queued_spin_lock_slowpath+0x32b/0x520
[   16.042040]  __pv_queued_spin_lock_slowpath+0x32b/0x520
[   16.042328]  ? memcpy+0x39/0x60
[   16.042552]  ? pv_hash+0xd0/0xd0
[   16.042785]  ? lockdep_hardirqs_off+0x95/0xd0
[   16.043079]  __bpf_spin_lock_irqsave+0xdf/0xf0
[   16.043366]  ? bpf_get_current_comm+0x50/0x50
[   16.043608]  ? jhash+0x11a/0x270
[   16.043848]  bpf_timer_cancel+0x34/0xe0
[   16.044119]  bpf_prog_c4ea1c0f7449940d_sys_enter+0x7c/0x81
[   16.044500]  bpf_trampoline_6442477838_0+0x36/0x1000
[   16.044836]  __x64_sys_nanosleep+0x5/0x140
[   16.045119]  do_syscall_64+0x59/0x80
[   16.045377]  ? lock_is_held_type+0xe4/0x140
[   16.045670]  ? irqentry_exit_to_user_mode+0xa/0x40
[   16.046001]  ? mark_held_locks+0x24/0x90
[   16.046287]  ? asm_exc_page_fault+0x1e/0x30
[   16.046569]  ? asm_exc_page_fault+0x8/0x30
[   16.046851]  ? lockdep_hardirqs_on+0x7e/0x100
[   16.047137]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[   16.047405] RIP: 0033:0x7f9e4831718d
[   16.047602] Code: b4 0c 00 0f 05 eb a9 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d b3 6c 0c 00 f7 d8 64 89 01 48
[   16.048764] RSP: 002b:00007fff488086b8 EFLAGS: 00000206 ORIG_RAX: 0000000000000023
[   16.049275] RAX: ffffffffffffffda RBX: 00007f9e48683740 RCX: 00007f9e4831718d
[   16.049747] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007fff488086d0
[   16.050225] RBP: 00007fff488086f0 R08: 00007fff488085d7 R09: 00007f9e4cb594a0
[   16.050648] R10: 0000000000000000 R11: 0000000000000206 R12: 00007f9e484cde30
[   16.051124] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
[   16.051608]  </TASK>
[   16.051762] ==================================================================

Fixes: 68134668c17f ("bpf: Add map side support for bpf timers.")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220209070324.1093182-2-memxor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Update the list of the PCI supported devices

commit f908a35b22180c4da64cf2647e4f5f0cd3054da7 upstream.

Add the upcoming BlueField-4 and ConnectX-8 device IDs.

Fixes: 2e9d3e83ab82 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ice: initialize local variable 'tlv'

commit 5950bdc88dd1d158f2845fdff8fb1de86476806c upstream.

Clang static analysis reports this issues
ice_common.c:5008:21: warning: The left expression of the compound
  assignment is an uninitialized value. The computed value will
  also be garbage
  ldo->phy_type_low |= ((u64)buf << (i * 16));
  ~~~~~~~~~~~~~~~~~ ^

When called from ice_cfg_phy_fec() ldo is the uninitialized local
variable tlv.  So initialize.

Fixes: ea78ce4dab05 ("ice: add link lenient and default override support")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ice: check the return of ice_ptp_gettimex64

commit ed22d9c8d128293fc7b0b086c7d3654bcb99a8dd upstream.

Clang static analysis reports this issue
time64.h:69:50: warning: The left operand of '+'
  is a garbage value
  set_normalized_timespec64(&ts_delta, lhs.tv_sec + rhs.tv_sec,
                                       ~~~~~~~~~~ ^
In ice_ptp_adjtime_nonatomic(), the timespec64 variable 'now'
is set by ice_ptp_gettimex64().  This function can fail
with -EBUSY, so 'now' can have a gargbage value.
So check the return.

Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Fix tc max supported prio for nic mode

commit be7f4b0ab149afd19514929fad824b2117d238c9 upstream.

Only prio 1 is supported if firmware doesn't support ignore flow
level for nic mode. The offending commit removed the check wrongly.
Add it back.

Fixes: 9a99c8f1253a ("net/mlx5e: E-Switch, Offload all chain 0 priorities when modify header and forward action is not supported")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: Handle failure to register sensor with thermal zone correctly

commit 1b5f517cca36292076d9e38fa6e33a257703e62e upstream.

If an attempt is made to a sensor with a thermal zone and it fails,
the call to devm_thermal_zone_of_sensor_register() may return -ENODEV.
This may result in crashes similar to the following.

Unable to handle kernel NULL pointer dereference at virtual address 00000000000003cd
...
Internal error: Oops: 96000021 [#1] PREEMPT SMP
...
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mutex_lock+0x18/0x60
lr : thermal_zone_device_update+0x40/0x2e0
sp : ffff800014c4fc60
x29: ffff800014c4fc60 x28: ffff365ee3f6e000 x27: ffffdde218426790
x26: ffff365ee3f6e000 x25: 0000000000000000 x24: ffff365ee3f6e000
x23: ffffdde218426870 x22: ffff365ee3f6e000 x21: 00000000000003cd
x20: ffff365ee8bf3308 x19: ffffffffffffffed x18: 0000000000000000
x17: ffffdde21842689c x16: ffffdde1cb7a0b7c x15: 0000000000000040
x14: ffffdde21a4889a0 x13: 0000000000000228 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000001120000 x7 : 0000000000000001 x6 : 0000000000000000
x5 : 0068000878e20f07 x4 : 0000000000000000 x3 : 00000000000003cd
x2 : ffff365ee3f6e000 x1 : 0000000000000000 x0 : 00000000000003cd
Call trace:
 mutex_lock+0x18/0x60
 hwmon_notify_event+0xfc/0x110
 0xffffdde1cb7a0a90
 0xffffdde1cb7a0b7c
 irq_thread_fn+0x2c/0xa0
 irq_thread+0x134/0x240
 kthread+0x178/0x190
 ret_from_fork+0x10/0x20
Code: d503201f d503201f d2800001 aa0103e4 (c8e47c02)

Jon Hunter reports that the exact call sequence is:

hwmon_notify_event()
  --> hwmon_thermal_notify()
    --> thermal_zone_device_update()
      --> update_temperature()
        --> mutex_lock()

The hwmon core needs to handle all errors returned from calls
to devm_thermal_zone_of_sensor_register(). If the call fails
with -ENODEV, report that the sensor was not attached to a
thermal zone  but continue to register the hwmon device.

Reported-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Fixes: 1597b374af222 ("hwmon: Add notification support")
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Fix incorrect multicast rx mask setting when not requested

commit 8cdb15924252e27af16c4a8fe0fc606ce5fd04dc upstream.

We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked.  Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.

Fixes: 7d2837dd7a32 ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Fix offline ethtool selftest with RDMA enabled

commit 6758f937669dba14c6aac7ca004edda42ec1b18d upstream.

For offline (destructive) self tests, we need to stop the RDMA driver
first.  Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.

The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.

Fixes: 55fd0cf320c3 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Fix active FEC reporting to ethtool

commit 84d3c83e6ea7d46cf3de3a54578af73eb24a64f2 upstream.

ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None.  Fix it to properly return
ETHTOOL_FEC_OFF in that case.

Fixes: 8b2775890ad8 ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnx2x: fix driver load from initrd

commit e13ad1443684f7afaff24cf207e85e97885256bd upstream.

Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.

Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: mptcp: be more conservative with cookie MPJ limits

commit e35f885b357d47e04380a2056d1b2cc3e6f4f24b upstream.

Since commit 2843ff6f36db ("mptcp: remote addresses fullmesh"), an
MPTCP client can attempt creating multiple MPJ subflow simultaneusly.

In such scenario the server, when syncookies are enabled, could end-up
accepting incoming MPJ syn even above the configured subflow limit, as
the such limit can be enforced in a reliable way only after the subflow
creation. In case of syncookie, only after the 3rd ack reception.

As a consequence the related self-tests case sporadically fails, as it
verify that the server always accept the expected number of MPJ syn.

Address the issues relaxing the MPJ syn number constrain. Note that the
check on the accepted number of MPJ 3rd ack still remains intact.

Fixes: 2843ff6f36db ("mptcp: remote addresses fullmesh")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: mptcp: fix diag instability

commit 0cd33c5ffec12bd77a1c02db2469fac08f840939 upstream.

Instead of waiting for an arbitrary amount of time for the MPTCP
MP_CAPABLE handshake to complete, explicitly wait for the relevant
socket to enter into the established status.

Additionally let the data transfer application use the slowest
transfer mode available (-r), to cope with very slow host, or
high jitter caused by hosting VMs.

Fixes: df62f2ec3df6 ("selftests/mptcp: add diag interface tests")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/258
Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mptcp: add mibs counter for ignored incoming options

commit f73c1194634506ab60af0debef04671fc431a435 upstream.

The MPTCP in kernel path manager has some constraints on incoming
addresses announce processing, so that in edge scenarios it can
end-up dropping (ignoring) some of such announces.

The above is not very limiting in practice since such scenarios are
very uncommon and MPTCP will recover due to ADD_ADDR retransmissions.

This patch adds a few MIB counters to account for such drop events
to allow easier introspection of the critical scenarios.

Fixes: f7efc7771eac ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mptcp: fix race in incoming ADD_ADDR option processing

commit 837cf45df163a3780bc04b555700231e95b31dc9 upstream.

If an MPTCP endpoint received multiple consecutive incoming
ADD_ADDR options, mptcp_pm_add_addr_received() can overwrite
the current remote address value after the PM lock is released
in mptcp_pm_nl_add_addr_received() and before such address
is echoed.

Fix the issue caching the remote address value a little earlier
and always using the cached value after releasing the PM lock.

Fixes: f7efc7771eac ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf data: Fix double free in perf_session__delete()

commit 69560e366fc4d5fca7bebb0e44edbfafc8bcaf05 upstream.

When perf_data__create_dir() fails, it calls close_dir(), but
perf_session__delete() also calls close_dir() and since dir.version and
dir.nr were initialized by perf_data__create_dir(), a double free occurs.

This patch moves the initialization of dir.version and dir.nr after
successful initialization of dir.files, that prevents double freeing.
This behavior is already implemented in perf_data__open_dir().

Fixes: 145520631130bd64 ("perf data: Add perf_data__(create_dir|close_dir) functions")
Signed-off-by: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Antonov <alexander.antonov@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Budankov <abudankov@huawei.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220218152341.5197-2-alexey.v.bayduraev@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf evlist: Fix failed to use cpu list for uncore events

commit 8a3d2ee0de3828e0d01f9682d35ee53704659bd0 upstream.

The 'perf record' and 'perf stat' commands have supported the option
'-C/--cpus' to count or collect only on the list of CPUs provided.

Commit 1d3351e631fc34d7 ("perf tools: Enable on a list of CPUs for
hybrid") add it to be supported for hybrid. For hybrid support, it
checks the cpu list are available on hybrid PMU. But when we test only
uncore events(or events not in cpu_core and cpu_atom), there is a bug:

Before:

 # perf stat -C0  -e uncore_clock/clockticks/ sleep 1
   failed to use cpu list 0

In this case, for uncore event, its pmu_name is not cpu_core or
cpu_atom, so in evlist__fix_hybrid_cpus, perf_pmu__find_hybrid_pmu
should return NULL,both events_nr and unmatched_count should be 0 ,then
the cpu list check function evlist__fix_hybrid_cpus return -1 and the
error "failed to use cpu list 0" will happen. Bypass "events_nr=0" case
then the issue is fixed.

After:

 # perf stat -C0  -e uncore_clock/clockticks/ sleep 1

 Performance counter stats for 'CPU(s) 0':

       195,476,873      uncore_clock/clockticks/

       1.004518677 seconds time elapsed

When testing with at least one core event and uncore events, it has no
issue.

 # perf stat -C0  -e cpu_core/cpu-cycles/,uncore_clock/clockticks/ sleep 1

 Performance counter stats for 'CPU(s) 0':

         5,993,774      cpu_core/cpu-cycles/
       301,025,912      uncore_clock/clockticks/

       1.003964934 seconds time elapsed

Fixes: 1d3351e631fc34d7 ("perf tools: Enable on a list of CPUs for hybrid")
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: alexander.shishkin@intel.com
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20220218093127.1844241-1-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpu: host1x: Always return syncpoint value when waiting

commit 184b58fa816fb5ee1854daf0d430766422bf2a77 upstream.

The new TegraDRM UAPI uses syncpoint waiting with timeout set to
zero to indicate reading the syncpoint value. To support that we
need to return the syncpoint value always when waiting.

Fixes: 44e961381354 ("drm/tegra: Implement syncpoint wait UAPI")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"

commit fe20371578ef640069e6ae9fa8038f60e7908565 upstream.

Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.

Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to  configure TC map 0 for VSI 391

This reverts commit 3d2504663c41104b4359a15f35670cfa82de1bbf.

Fixes: 3d2504663c41 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ping: remove pr_err from ping_lookup

commit cd33bdcbead882c2e58fdb4a54a7bd75b610a452 upstream.

As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().

Fixes: 35a79e64de29 ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

optee: use driver internal tee_context for some rpc

commit aceeafefff736057e8f93f19bbfbef26abd94604 upstream.

Adds a driver private tee_context by moving the tee_context in struct
optee_notif to struct optee. This tee_context was previously used when
doing internal calls to secure world to deliver notification.

The new driver internal tee_context is now also when allocating driver
private shared memory. This decouples the shared memory object from its
original tee_context. This is needed when the life time of such a memory
allocation outlives the client tee_context.

This patch fixes the problem described below:

The addition of a shutdown hook by commit f25889f93184 ("optee: fix tee out
of memory failure seen during kexec reboot") introduced a kernel shutdown
regression that can be triggered after running the OP-TEE xtest suites.

Once the shutdown hook is called it is not possible to communicate any more
with the supplicant process because the system is not scheduling task any
longer. Thus if the optee driver shutdown path receives a supplicant RPC
request from the OP-TEE we will deadlock the kernel's shutdown.

Fixes: f25889f93184 ("optee: fix tee out of memory failure seen during kexec reboot")
Fixes: 217e0250cccb ("tee: use reference counting for tee_context")
Reported-by: Lars Persson <larper@axis.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
[JW: backport to 5.15-stable + update commit message]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tee: export teedev_open() and teedev_close_context()

commit 1e2c3ef0496e72ba9001da5fd1b7ed56ccb30597 upstream.

Exports the two functions teedev_open() and teedev_close_context() in
order to make it easier to create a driver internal struct tee_context.

Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_tables_offload: incorrect flow offload action array size

commit b1a5983f56e371046dcf164f90bfaf704d2b89f6 upstream.

immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.

fwd and dup expression need to allocate one slot, this is missing.

Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.

Fixes: be2861dc36d7 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: xt_socket: missing ifdef CONFIG_IP6_NF_IPTABLES dependency

commit 2874b7911132f6975e668f6849c8ac93bc4e1f35 upstream.

nf_defrag_ipv6_disable() requires CONFIG_IP6_NF_IPTABLES.

Fixes: 75063c9294fb ("netfilter: xt_socket: fix a typo in socket_mt_destroy()")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Eric Dumazet<edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: xt_socket: fix a typo in socket_mt_destroy()

commit 75063c9294fb239bbe64eb72141b6871fe526d29 upstream.

Calling nf_defrag_ipv4_disable() instead of nf_defrag_ipv6_disable()
was probably not the intent.

I found this by code inspection, while chasing a possible issue in TPROXY.

Fixes: de8c12110a13 ("netfilter: disable defrag once its no longer needed")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CDC-NCM: avoid overflow in sanity checking

commit 8d2b1a1ec9f559d30b724877da4ce592edc41fdc upstream.

A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: zaurus: support another broken Zaurus

commit 6605cc67ca18b9d583eb96e18a20f5f4e726103c upstream.

This SL-6000 says Direct Line, not Ethernet

v2: added Reporter and Link

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Ross Maynard <bids.7405@bigpond.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215361
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sr9700: sanity check for packet length

commit e9da0b56fe27206b49f39805f7dcda8a89379062 upstream.

A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Fix bw atomic check when switching between SAGV vs. no SAGV

commit ec663bca9128f13eada25cd0446e7fcb5fcdc088 upstream.

If the only thing that is changing is SAGV vs. no SAGV but
the number of active planes and the total data rates end up
unchanged we currently bail out of intel_bw_atomic_check()
early and forget to actually compute the new WGV point
mask and thus won't actually enable/disable SAGV as requested.
This ends up poorly if we end up running with SAGV enabled
when we shouldn't. Usually ends up in underruns.

To fix this let's go through the QGV point mask computation
if either the data rates/number of planes, or the state
of SAGV is changing.

v2: Check more carefully if things are changing to avoid
    the extra calculations/debugs from introducing unwanted
    overhead

Cc: stable@vger.kernel.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Fixes: 20f505f22531 ("drm/i915: Restrict qgv points which don't have enough bandwidth.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218064039.12834-3-ville.syrjala@linux.intel.com
(cherry picked from commit 6b728595ffa51c087343c716bccbfc260f120e72)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Correctly populate use_sagv_wm for all pipes

commit afc189df6bcc6be65961deb54e15ec60e7f85337 upstream.

When changing between SAGV vs. no SAGV on tgl+ we have to
update the use_sagv_wm flag for all the crtcs or else
an active pipe not already in the state will end up using
the wrong watermarks. That is especially bad when we end up
with the tighter non-SAGV watermarks with SAGV enabled.
Usually ends up in underruns.

Cc: stable@vger.kernel.org
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 7241c57d3140 ("drm/i915: Add TGL+ SAGV support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218064039.12834-2-ville.syrjala@linux.intel.com
(cherry picked from commit 8dd8ffb824ca7b897ce9f2082ffa7e64831c22dc)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Widen the QGV point mask

commit 3f33364836aacc28cd430d22cf22379e3b5ecd77 upstream.

adlp+ adds some extra bits to the QGV point mask. The code attempts
to handle that but forgot to actually make sure we can store those
bits in the bw state. Fix it.

Cc: stable@vger.kernel.org
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 192fbfb76744 ("drm/i915: Implement PSF GV point support")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214091811.13725-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit c0299cc9840b3805205173cc77782f317b78ea0e)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: do not enable asic reset for raven2

commit 1e2be869c8a7247a7253ef4f461f85e2f5931b95 upstream.

The GPU reset function of raven2 is not maintained or tested, so it should be
very unstable.

Now the amdgpu_asic_reset function is added to amdgpu_pmops_suspend, which
causes the S3 test of raven2 to fail, so the asic_reset of raven2 is ignored
here.

Fixes: daf8de0874ab5b ("drm/amdgpu: always reset the asic in suspend (v2)")
Signed-off-by: Chen Gong <curry.gong@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: disable MMHUB PG for Picasso

commit f626dd0ff05043e5a7154770cc7cda66acee33a3 upstream.

MMHUB PG needs to be disabled for Picasso for stability reasons.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd: Check if ASPM is enabled from PCIe subsystem

commit 7294863a6f01248d72b61d38478978d638641bee upstream.

commit 0064b0ce85bb ("drm/amd/pm: enable ASPM by default") enabled ASPM
by default but a variety of hardware configurations it turns out that this
caused a regression.

* PPC64LE hardware does not support ASPM at a hardware level.
  CONFIG_PCIEASPM is often disabled on these architectures.
* Some dGPUs on ALD platforms don't work with ASPM enabled and PCIe subsystem
  disables it

Check with the PCIe subsystem to see that ASPM has been enabled
or not.

Fixes: 0064b0ce85bb ("drm/amd/pm: enable ASPM by default")
Link: https://wiki.raptorcs.com/w/images/a/ad/P9_PHB_version1.0_27July2018_pub.pdf
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1723
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1739
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1885
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1907
Tested-by: koba.ko@canonical.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: fix some OEM SKU specific stability issues

commit e3f3824874da78db5775a5cb9c0970cd1c6978bc upstream.

Add a quirk in sienna_cichlid_ppt.c to fix some OEM SKU
specific stability issues.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/display: Protect update_bw_bounding_box FPU code.

commit 1432108d00e42ffa383240bcac8d58f89ae19104 upstream.

For DCN3/3.01/3.02 at least these use the fpu.

v2: squash in build fix for when DCN is not enabled (Leo)

Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>