parport: parport_serial: Add support for Sunix Multi I/O boards

Sunix Multi I/O boards are different to Timedia's.

This patch adds proper support for Sunix MIO boards with 1 parallel and
up to 4 serial ports.

Cc: Morris Ku <morris_ku@sunix.com>
Cc: Debbie Liu <debbie_liu@sunix.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190809190130.30773-2-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_pci: Add support for Sunix serial boards

Add support to Sunix serial boards with up to 16 ports.

Sunix board need its own setup callback instead of using Timedia's, to
properly support more than 4 ports.

Cc: Morris Ku <morris_ku@sunix.com>
Cc: Debbie Liu <debbie_liu@sunix.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20190809190130.30773-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: remove ks8695 driver

The platform is getting removed, so there are no more users
of this driver.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190809202749.742267-3-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: lantiq: Add support for Lightning Mountain SoC

This patch adds IRQ & ISR support in the driver for Lightning Mountain SoC.

Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/0df20f6e4bbf9de09c85a5c92c92e642f62f441f.1565257887.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: lantiq: Make IRQ & ISR assignment dynamic

This driver/IP is reused across multiple SoCs. Older SoCs supported three
separate IRQs for tx, rx & err interrupts. Newer Lightning Mountain SoC
supports single IRQ for all of tx/rx/err interrupts. This patch modifies
the driver design to support dynamic assignment of IRQ resources & ISRs
based on devicetree node compatible entries.

Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/b166a0593bee191fcd77b5bdf8fedc6f6330a371.1565257887.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: lantiq: Use proper DT compatible string

Use explicit string instead of a macro for devicetree compatible string.

This series of patches is to add support for multiple SoCs which reuse the same
serial controller IP. The following patches will add another compatible string
to support new Lightning Mountain(LGM) SoC. So it makes sense to have the
compatible strings explicitly mentioned instead of a fixed macro.

Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/57e2b69e9fbd93328a477b4c7dd2dcc78784ecb1.1565257887.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_lpss: Enable HS UART on Elkhart Lake

Intel Elkhart Lake may use High Speed UART from OSE IP block.
This is different to what we have in main LPSS, though compatible
with older version of it, which is handled by this driver.

Enable OSE HS UART on Intel Elkhart Lake by adding PCI IDs.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_lpss: Get rid of custom LPSS_DEVICE() macro

Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace LPSS_DEVICE() with former one.

No functional change intended.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_lpss: register DMA IRQ and pool with instance ID

It is really useful not only for debugging to have an DMA IRQ line and
pool being mapped to the corresponding IP by using its instance ID.

Provide PCI device and function as instance ID for Intel Quark UART DMA.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_lpss: add fractional divisor support

For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register.

Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups specific get_divisor() and set_divisor() hook.

Among other changes the FIFO size is now retrieved from the hardware.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_lpss: switch to use 8250_dwlib library

Since we have a common library module for Synopsys DesignWare UART,
let us use it.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: switch to use 8250_dwlib library

Since we have a common library module for Synopsys DesignWare UART,
let us use it.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: split Synopsys DesignWare 8250 common functions

We would like to use same functions in the couple of drivers for
Synopsys DesignWare 8250 UART. Split them from 8250_dw into new brand
library module which users will select explicitly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: use pointer to uart local variable

The use of pointer will simplify enabling runtime PM for the driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190806094322.64987-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_dw: Use a unified new dev variable in remove

The commit 2cb78eab2376 ("serial: 8250_dw: Use a unified new dev variable in
probe") introduced a local dev variable in ->probe(). Do the same in ->remove()
in order to prepare for sequential patches.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Link: https://lore.kernel.org/r/20190806094322.64987-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: lantiq: Add SMP support

The existing driver can only support single core SoC. But new multicore
platforms which reuse the same driver/IP need SMP support. This patch adds
multicore support in the driver.

Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/7912786cccad60c72b20ea724af1def505ab22aa.1565160764.git.rahul.tanwar@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Ignore TX/RX interrupts if DMA is enabled

In a mixed DMA/IRQ use-case (e.g.: DMA for TX, IRQ for RX), interrupt
handler might try to handle Rx/Tx condition it shouldn't. Change the
code to only handle TX/RX event if corresponding path isn't being
handled by DMA.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-7-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Don't enable TIE in .startup() or .resume()

Enabling TIE in .startup() callback causes the driver to start (or at
least try) to transmit data before .start_tx() is called. Which, while
harmless (since TIE handler will immediately disable it), is a no-op
and shouldn't really happen. Drop UARTCR2_TIE from list of bits set in
lpuart_startup().

This change will also not enable TIE in .resume(), but it seems that,
similart to .startup(), transmit interrupt shouldn't be enabled there
either.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-6-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Introduce lpuart*_setup_watermark_enable()

Most users of lpuart*_setup_watermark() enable identical set of flags
right after the call, so combine those two action into a subroutine
and make use of it.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-5-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Introduce lpuart32_configure()

Code doing final steps of TX/RX configuration in lpuart32_startup()
and lpuart_resume() is identical, so move it into a standalone
subroutine.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-4-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Introduce lpuart_rx_dma_startup()

Code doing initial DMA RX configuration in lpuart_startup() and
lpuart32_startup() is exactly the same, so move it into a standalone
subroutine.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-3-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Introduce lpuart_tx_dma_startup()

Code configure DMA TX path in lpuart_startup(), lpuart32_startup() and
lpuart_resume() is doing exactly the same thing, so move it into a
standalone subroutine.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190805185701.22863-2-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Replace msleep(1) with usleep_range()

As explained in Documentation/timers/timers-howto.rst
the small amount of milliseconds sometimes produces
much longer delays.

Replace msleep(1) with usleep_range(1000, 1100).

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190805142535.21948-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Consolidate callback assignments in default_setup()

For better maintenance consolidate port callbacks in default_setup().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190805142535.21948-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: qcom_geni_serial: use devm_platform_ioremap_resource() to simplify code

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190802130817.16220-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: Don't check for mctrl_gpio_init() returning -ENOSYS

Now that the mctrl_gpio code returns NULL instead of ERR_PTR(-ENOSYS)
if CONFIG_GPIOLIB is disabled, we can safely remove this check.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-4-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sh-sci: Don't check for mctrl_gpio_init() returning -ENOSYS

Now that the mctrl_gpio code returns NULL instead of ERR_PTR(-ENOSYS)
if CONFIG_GPIOLIB is disabled, we can safely remove this check.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-3-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: mctrl_gpio: Avoid probe failures in case of missing gpiolib

If CONFIG_GPIOLIB is not enabled, mctrl_gpio_init() and
mctrl_gpio_init_noauto() will currently return an error pointer with
-ENOSYS. As the mctrl GPIOs are usually optional, drivers need to
check for this condition to allow continue probing.

To avoid the need for this check in each driver, we return NULL
instead, as all the mctrl_gpio_*() functions are skipped anyway.
We also adapt mctrl_gpio_to_gpiod() to be in line with this change.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20190802100349.8659-1-frieder.schrempf@kontron.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Absorb remaining 8250_port INT0 support

Move INT0 clearing out of common, per-port serial8250_do_startup()
into PCI device probe/resume.

As described in commit 2c0ac5b48a35 ("serial: exar: Fix stuck MSIs"),
the purpose of clearing INT0 is to prevent the PCI interrupt line from
becoming stuck asserted, "which is fatal with edge-triggered MSIs".

Like the clearing via interrupt handler that moved from common code in
commit c7e1b4059075 ("tty: serial: exar: Relocate sleep wake-up
handling"), this clearing at startup can be better handled at the PCI
device level.

Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190801185956.3222-1-asierra@xes-inc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sh-sci: Use DEVICE_ATTR_RW() for rx_fifo_trigger

While commit b6b996b6cdeecf7e ("treewide: Use DEVICE_ATTR_RW") converted
the rx_fifo_timeout attribute, it forgot to convert rx_fifo_trigger due
to a slightly different function naming.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20190731124555.14349-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: qcom_geni_serial: Update the oversampling rate

For QUP IP versions 2.5 and above the oversampling rate is halved
from 32 to 16. Update this rate after reading hardware version
register, so that the clock divider value is correctly set to
achieve required baud rate.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Link: https://lore.kernel.org/r/20190801121153.10613-1-vivek.gautam@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Clear buffer before shutdown

When closing and shutting down the exar serial port, if the chip
has not finished sending all of the data in its buffer, the
remaining bytes will be lost.  Hold off on the shutdown until the
bytes have all been sent.

Signed-off-by: Robert Middleton <robert.middleton@rm5248.com>
Link: https://lore.kernel.org/r/20190801145640.26080-1-robert.middleton@rm5248.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Move custom divisor support out from 8250_port

There are Exar custom divisor support in 8250_port which belongs to
8250_exar module. Move it out to the correct module and do not contaminate
generic code with it.

Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Extract PM routine from 8250_port

There are Exar quirks in 8250_port which belong to 8250_exar module.
Extract PM routine to the correct module and do not contaminate generic code
with it.

Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: No need to autoconfigure Exar ports

Since we have a separate driver there is no need to autoconfigure ports,
we already know what they are.

Drop autoconfiguration in 8250_port and move type detection to 8250_exar.

Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190731170558.52897-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sh-sci: use driver core functions, not sysfs ones.

This is a driver, do not call "raw" sysfs functions, instead call driver
core ones.  Specifically convert the use of sysfs_create_file() and
sysfs_remove_file() to use device_create_file() and device_remove_file()

Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20190704084617.3602-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xilinx_uartps.c: suppress "may be used uninitialised" warning

A powerpc allyesconfig build produces this warning:

In file included from include/linux/radix-tree.h:16,
                 from include/linux/idr.h:15,
                 from include/linux/kernfs.h:13,
                 from include/linux/sysfs.h:16,
                 from include/linux/kobject.h:20,
                 from include/linux/device.h:16,
                 from include/linux/platform_device.h:13,
                 from drivers/tty/serial/xilinx_uartps.c:16:
drivers/tty/serial/xilinx_uartps.c: In function 'cdns_uart_console_write':
include/linux/spinlock.h:288:3: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
   _raw_spin_unlock_irqrestore(lock, flags); \
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/xilinx_uartps.c:1197:16: note: 'flags' was declared here
  unsigned long flags;
                ^~~~~

It looks like gcc just can't track the relationship between "locked"
and "flags", and it is obvious that "flags" won't be used when "locked"
is zero, so the simplest thing is to initialise flags.

Cc: Jiri Slaby <jslaby@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20190731160557.6a09c3e1@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: Remove dev_err() usage after platform_get_irq()

We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-45-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Introduce lpuart_dma_shutdown()

Last steps of .shutdown() code are identical for lpuart and lpuart32
cases, so move it all into a standalone subroutine.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-19-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Drop unnecessary lpuart*_stop_tx()

By the time lpuart_shutdown() calls lpuart_stop_tx() UARTCR2_TE and
UARTCR2_TIE (which the latter will clear) are already cleared, so that
function call should effectively be a no-op. Moreso, lpuart_stop_tx()
is expected to be executed with port spinlock held, which the caller
doesn't. Given all that, drop the call to lpuart_stop_tx() in
lpuart_shutdown().

In case of lpuart32_shutdown()/lpuart32_stop_tx(), TIE won't even be
set if lpuart_dma_tx_use is true. Drop it there as well.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-18-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Introduce lpuart_stopped_or_empty()

The check for

    uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)

appears in multiple places in the driver. Move it into a helper
function.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-17-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Use cpu_relax() instead of barrier()

Use cpu_relax() instead of barrier() in a tight polling loops to make
them a bit more idiomatic. Should also improve things on ARM64 a bit
since cpu_relax() will expand into "yield" instruction there.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-16-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Introduce lpuart_wait_bit_set()

Busy polling on a bit in a register is used in multiple places in the
driver. Move it into a shared function.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-15-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs

When dealing with 32-bit variant of LPUART IP block appropriate I/O
helpers have to be used to properly deal with endianness
differences. Change all of the offending code to do that.

Fixes: a5fa2660d787 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support
for lpuart32.")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Clear CSTOPB unconditionally

Clearing CSTOPB bit if it is set is functionally equivalent to jsut
clearing it unconditionally. Drop unnecessary check.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-13-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Drop unnecessary extra parenthesis

Drop unnecessary extra parenthesis in the driver.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-12-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Drop no-op bit opearation

The check for termios->c_cflag & CRTSCTS ensure that if we reach else
branch, CRTSCTS in termios->c_cflag is already going to be
cleard. Doing so explicitly there is not necessary. Drop it.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-11-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fls_lpuart: Split shared TX IRQ handler into two

While sharing code for Tx interrupt handler between 8 and 32 bit
variant of the peripheral saves a bit of code duplication it also adds
quite a number of lpuart_is_32() checks which makes it harder to
understand. Move shared bits back into corresponding
lpuart*_transmit_buffer functions, split lpuart_txint into
lpuart_txint and lpuart32_txint so we can drop all extra
lpuart_is_32() check and make the code flow more linear.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-10-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Fix issue in software flow control

Although I haven't observed this bug in practice, it seems that the
code for handling x_char of LPUART is pretty much identical to that of
i.MX. So the fix found in commit 7e2fb5aa8d81 ("serial: imx: Fix issue
in software flow control"):

    serial: imx: Fix issue in software flow control

    After send out x_char in UART driver, x_char needs to be cleared
    by UART driver itself, otherwise data in TXFIFO can no longer be
    sent out.
    Also tx counter needs to be increased to keep track of correct
    number of transmitted data.

Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
should apply here as well.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-9-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Drop unnecessary uart_write_wakeup()

Uart_write_wakeup() will already be called as a part of
lpuart*_transmit_buffer() call, so there doesn't seem to be a reason
to call it again right after.

It also appears that second uart_write_wakeup() might potentially
cause unwanted write wakeup when transmitting an x_char. See commit
5e42e9a30cda ("serial: imx: Fix x_char handling and tx flow control")
where this problem was fixed in a very similarly structured i.MX UART
driver.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-8-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Fix bogus indentation

Fix bogus indentation in rx_dma_timer_init().

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-6-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Simplify RX/TX IRQ handlers

It appears that lpuart_rxint, lpuart_txint and lpuart32_rxint were
modelled after identical function found in UART driver for
i.MX. However, while said functions are used as individual IRQ
handlers in i.MX driver (in case of i.MX1), it is not the case for
LPUART. Given that, there's no need for us to restrict the prototype
of the handler to irqreturn_t foo(int, void *) and we can drop all of
uneened boilerplate code by changing it void foo(struct lpuart_port *).

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-5-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: Flush HW FIFOs in .flush_buffer

Switching baud rate might cause bogus data to appear in HW
FIFO. Add code to do a HW FIFO flush to .flush_buffer callback to
avoid that.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-4-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: flush receive FIFO after overruns

After overruns the FIFO pointers become misaligned. This
typically shows by characters still being stuck in the FIFO
despite the empty flag being asserted. After the first
assertion of the overrun flag the empty flag still seems to
indicate FIFO state correctly and all data can be read.
However, after another overrun assertion the FIFO seems to
be off by one such that the last received character is still
in the FIFO (despite the empty flag being asserted).

Flushing the receive FIFO reinitializes pointers. Hence it
is recommended to flush the FIFO after overruns, see also:
https://community.nxp.com/thread/321175

Hence, on assertion of the overrun flag read the remaining
data from the FIFO and flush buffers.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-3-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: fix framing error handling when using DMA

When using DMA framing error get cleared properly. However, due
to the additional read from the data register, an underflow in
the receive FIFO buffer occurs (the FIFO pointer gets out of
sync).

Clear the FIFO in case an underflow has occurred. Also disable the
receiver during this operation and when reading the data register to
minimize potential interference.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-2-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: imx: get rid of imx_uart_rts_auto()

Called in only one place, for RS232, it only obscures things, as it
doesn't go well with 2 similar named functions,
imx_uart_rts_inactive() and imx_uart_rts_active(), that both are
RS485-specific.

Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-4-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: imx: set_mctrl(): correctly restore autoRTS state

imx_uart_set_mctrl() happened to set UCR2_CTSC bit whenever TIOCM_RTS
was set, no matter if RTS/CTS handshake is enabled or not. Now fixed by
turning handshake on only when CRTSCTS bit for the port is set.

Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: imx: set_termios(): do not enable autoRTS if RTS is unset

Don't let receiver hardware automatically control RTS output if it
was requested to be inactive.

To ensure this, set_termios() shouldn't set UCR2_CTSC bit if UCR2_CTS
(=TIOCM_RTS) is cleared. Added corresponding check in imx_uart_rts_auto()
to fix this.

Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1564167161-3972-2-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_pnp: Move to struct dev_pm_ops

The established way to provide PM callbacks is through struct dev_pm_ops
which is more generic.

Convert driver to use it instead of legacy approach.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190726172817.73253-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial/8250: Add support for NI-Serial PXI/PXIe+485 devices

Add support for NI-Serial PXIe-RS232, PXI-RS485 and PXIe-RS485 devices.

Signed-off-by: Je Yen Tam <je.yen.tam@ni.com>
Link: https://lore.kernel.org/r/20190726074012.2590-1-je.yen.tam@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: stm32: Use __maybe_unused instead of #if CONFIG_PM_SLEEP

Use __maybe_unused for power management related functionsinstead of

fixes: 270e5a74fe4c ("serial: stm32: add wakeup mechanism")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/1560433800-12255-6-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: stm32: add pm_runtime support

Use pm_runtime for clock management.

Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/1560433800-12255-5-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: stm32: select pinctrl state in each suspend/resume function

Select either pinctrl sleep state in suspend function or default state in
resume function.

Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/1560433800-12255-4-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: serial: stm32: add wakeup option

Add a note for enabling wakeup capabilities of usart

Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1560433800-12255-2-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

8250_lpss: check null return when calling pci_ioremap_bar

pci_ioremap_bar may return null. This is eventually de-referenced at
drivers/dma/dw/core.c:1154 and drivers/dma/dw/core.c:1168. A null check
is needed to prevent null de-reference. I am adding the check and in
case of failure. Thanks to Andy Shevchenko for the hint on the necessity
of pci_iounmap when exiting.

Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20190719174848.24216-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: correct the FIFO depth size

VF610/LS1021a/i.MX7ULP/i.MX8QXP reference manual describe the
TXFIFOSIZE/RXFIFOSIZE field as below.

000b - FIFO/Buffer depth = 1 dataword.
001b - FIFO/Buffer depth = 4 datawords.
010b - FIFO/Buffer depth = 8 datawords.
011b - FIFO/Buffer depth = 16 datawords.
100b - FIFO/Buffer depth = 32 datawords.
101b - FIFO/Buffer depth = 64 datawords.
110b - FIFO/Buffer depth = 128 datawords.
111b - FIFO/Buffer depth = 256 datawords. (Reserved for VF610)

So the FIFO depth should be: 0x1 << (val ? (val + 1) : 0)

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-6-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: remove sg_set_buf() for sport->rx_sgl

Since .sg_init_one() already set sg entry page like below code.
sg_init_one()
sg_init_table(sg, 1);
sg_set_buf(sg, buf, buflen);

So it should not set sg entry page again, remove the redundant code.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-5-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: use kzalloc() instead of kmalloc()

Use kzalloc() instead of kmalloc() to get clean rx buffer
that is useful for DMA mode debug to check the data moving
validity.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-4-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: add earlycon for imx8qxp platform

Add earlycon support for imx8qxp platform.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-3-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: fsl_lpuart: remove the dev.coherent_dma_mask zero setting

By default, .of_dma_configure() init dev.coherent_dma_mask to BIT(32) that
match the eDMA address range. If re-init dev.coherent_dma_mask to zero, then
streaming dma mapping will go swiotlb dma_map, if swiotlb is not initalized
then it causes mapping failed.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20190717051930.15514-2-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: Use struct_size() helper

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array.

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190721150135.82065-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: nozomi: Use dev_get_drvdata

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20190724131825.1875-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: Use dev_get_drvdata where possible

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20190724131758.1764-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/isicom: remove redundant assignment to variable word_count

The variable word_count is being assigned a value that is never read before
a return, the assignment is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20190723150314.14513-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: Remove call to memset after pci_alloc_consistent

pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925c3
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190715032001.7212-1-huangfq.daxian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: hvcs: Fix odd use of strlcpy

Use the typical style of array, not the equivalent &array[0].

Signed-off-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/1be432798311378947ec4e6051cad1235b6eccbb.1562283944.git.joe@perches.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_omap: Fix idling for unloaded serdev drivers

For many years omap variants have been setting the runtime PM
autosuspend delay to -1 to prevent unsafe policy with lossy first
character on wake-up. The user must specifically enable the timeout
for UARTs if desired.

We must not enable the workaround for serdev devices though. It leads
into UARTs not idling if no serdev devices are loaded and there is no
sysfs entry to configure the UART in that case. And this means that
my PM may not work unless the serdev modules are loaded.

We can detect a serdev device being configured based on a dts child
node, and we can simply skip the workround in that case. And the
serdev driver can idle the port during runtime when suitable if an
out-of-band wake-up GPIO line exists for example.

Let's also add some comments to the workaround while at it.

Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20190723115400.46432-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: add helpers to convert mux-num to/from tty-base

Make it obvious how the gsm mux number relates to the virtual tty lines
by using helper functions instead of shifting 6 bits.

Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20190710192656.60381-3-martin@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: update doc example to use header for N_GSM0710 define

There is no reason to gues the line discipline number when it is
available from tty.h

Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20190710192656.60381-2-martin@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: remove obsolete mknod doc example

The n_gsm driver handles registration of /dev/gsmttyX nodes, so there's
no need to do mknod manually.

Signed-off-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20190710192656.60381-1-martin@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.3-rc4

Merge tag 'dax-fixes-5.3-rc4' of git://git./linux/kernel/git/nvdimm/nvdimm

Pull dax fixes from Dan Williams:
 "A filesystem-dax and device-dax fix for v5.3.

  The filesystem-dax fix is tagged for stable as the implementation has
  been mistakenly throwing away all cow pages on any truncate or hole
  punch operation as part of the solution to coordinate device-dma vs
  truncate to dax pages.

  The device-dax change fixes up a regression this cycle from the
  introduction of a common 'internal per-cpu-ref' implementation.

  Summary:

   - Fix dax_layout_busy_page() to not discard private cow pages of
     fs/dax private mappings.

   - Update the memremap_pages core to properly cleanup on behalf of
     internal reference-count users like device-dax"

* tag 'dax-fixes-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  mm/memremap: Fix reuse of pgmap instances with internal references
  dax: dax_layout_busy_page() should not unmap cow pages

Merge tag 'ntb-5.3-bugfixes' of git://github.com/jonmason/ntb

Pull NTB fix from Jon Mason:
 "Bug fix for NTB MSI kernel compile warning"

* tag 'ntb-5.3-bugfixes' of git://github.com/jonmason/ntb:
  NTB/msi: remove incorrect MODULE defines

Merge tag 'riscv/for-v5.3-rc4' of git://git./linux/kernel/git/riscv/linux

Pull RISC-V updates from Paul Walmsley:
 "A few minor RISC-V updates for v5.3-rc4:

   - Remove __udivdi3() from the 32-bit Linux port, converting the only
     upstream user to use do_div(), per Linux policy

   - Convert the RISC-V standard clocksource away from per-cpu data
     structures, since only one is used by Linux, even on a multi-CPU
     system

   - A set of DT binding updates that remove an obsolete text binding in
     favor of a YAML binding, fix a bogus compatible string in the
     schema (thus fixing a "make dtbs_check" warning), and clarifies the
     future values expected in one of the RISC-V CPU properties"

* tag 'riscv/for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  dt-bindings: riscv: fix the schema compatible string for the HiFive Unleashed board
  dt-bindings: riscv: remove obsolete cpus.txt
  RISC-V: Remove udivdi3
  riscv: delay: use do_div() instead of __udivdi3()
  dt-bindings: Update the riscv,isa string description
  RISC-V: Remove per cpu clocksource

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Thomas Gleixner:
 "A few fixes for x86:

   - Don't reset the carefully adjusted build flags for the purgatory
     and remove the unwanted flags instead. The 'reset all' approach led
     to build fails under certain circumstances.

   - Unbreak CLANG build of the purgatory by avoiding the builtin
     memcpy/memset implementations.

   - Address missing prototype warnings by including the proper header

   - Fix yet more fall-through issues"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/lib/cpu: Address missing prototypes warning
  x86/purgatory: Use CFLAGS_REMOVE rather than reset KBUILD_CFLAGS
  x86/purgatory: Do not use __builtin_memcpy and __builtin_memset
  x86: mtrr: cyrix: Mark expected switch fall-through
  x86/ptrace: Mark expected switch fall-through

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf tooling fixes from Thomas Gleixner:
 "Perf tooling fixes all over the place:

   - Fix the selection of the main thread COMM in db-export

   - Fix the disassemmbly display for BPF in annotate

   - Fix cpumap mask setup in perf ftrace when only one CPU is present

   - Add the missing 'cpu_clk_unhalted.core' event

   - Fix CPU 0 bindings in NUMA benchmarks

   - Fix the module size calculations for s390

   - Handle the gap between kernel end and module start on s390
     correctly

   - Build and typo fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf pmu-events: Fix missing "cpu_clk_unhalted.core" event
  perf annotate: Fix s390 gap between kernel end and module start
  perf record: Fix module size on s390
  perf tools: Fix include paths in ui directory
  perf tools: Fix a typo in a variable name in the Documentation Makefile
  perf cpumap: Fix writing to illegal memory in handling cpumap mask
  perf ftrace: Fix failure to set cpumask when only one cpu is present
  perf db-export: Fix thread__exec_comm()
  perf annotate: Fix printing of unaugmented disassembled instructions from BPF
  perf bench numa: Fix cpu0 binding

Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Thomas Gleixner:
 "Three fixlets for the scheduler:

   - Avoid double bandwidth accounting in the push & pull code

   - Use a sane FIFO priority for the Pressure Stall Information (PSI)
     thread.

   - Avoid permission checks when setting the scheduler params for the
     PSI thread"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/psi: Do not require setsched permission from the trigger creator
  sched/psi: Reduce psimon FIFO priority
  sched/deadline: Fix double accounting of rq/running bw in push & pull

Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull irq fix from Thomas Gleixner:
 "A small fix for the affinity spreading code.

  It failed to handle situations where a single vector was requested
  either due to only one CPU being available or vector exhaustion
  causing only a single interrupt to be granted.

  The fix is to simply remove the requirement in the affinity spreading
  code for more than one interrupt being available"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Create affinity mask for single vector

Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull objtool warning fix from Thomas Gleixner:
 "The recent objtool fixes/enhancements unearthed a unbalanced CLAC in
  the i915 driver.

  Chris asked me to pick the fix up and route it through"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  drm/i915: Remove redundant user_access_end() from __copy_from_user() error path

Merge tag 'gfs2-v5.3-rc3.fixes' of git://git./linux/kernel/git/gfs2/linux-gfs2

Pull gfs2 fix from Andreas Gruenbacher:
 "Fix incorrect lseek / fiemap results"

* tag 'gfs2-v5.3-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: gfs2_walk_metadata fix

Makefile: Convert -Wimplicit-fallthrough=3 to just -Wimplicit-fallthrough for clang

A compilation -Wimplicit-fallthrough warning was enabled by commit
a035d552a93b ("Makefile: Globally enable fall-through warning")

Even though clang 10.0.0 does not currently support this warning without
a patch, clang currently does not support a value for this option.

Link: https://bugs.llvm.org/show_bug.cgi?id=39382
The gcc default for this warning is 3 so removing the =3 has no effect
for gcc and enables the warning for patched versions of clang.

Also remove the =3 from an existing use in a parisc Makefile:
arch/parisc/math-emu/Makefile

Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-and-tested-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'char-misc-5.3-rc4' of git://git./linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes Greg KH:
 "Here are some small char/misc driver fixes for 5.3-rc4.

  Two of these are for the habanalabs driver for issues found when
  running on a big-endian system (are they still alive?) The others are
  tiny fixes reported by people, and a MAINTAINERS update about the
  location of the fpga development tree.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  coresight: Fix DEBUG_LOCKS_WARN_ON for uninitialized attribute
  MAINTAINERS: Move linux-fpga tree to new location
  nvmem: Use the same permissions for eeprom as for nvmem
  habanalabs: fix host memory polling in BE architecture
  habanalabs: fix F/W download in BE architecture

Merge tag 'driver-core-5.3-rc4' of git://git./linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are two small fixes for some driver core issues that have been
  reported. There is also a kernfs "fix" here, which was then reverted
  because it was found to cause problems in linux-next.

  The driver core fixes both resolve reported issues, one with gpioint
  stuff that showed up in 5.3-rc1, and the other finally (and hopefully)
  resolves a very long standing race when removing glue directories.
  It's nice to get that issue finally resolved and the developers
  involved should be applauded for the persistence it took to get this
  patch finally accepted.

  All of these have been in linux-next for a while with no reported
  issues. Well, the one reported issue, hence the revert :)"

* tag 'driver-core-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Revert "kernfs: fix memleak in kernel_ops_readdir()"
  kernfs: fix memleak in kernel_ops_readdir()
  driver core: Fix use-after-free and double free on glue directory
  driver core: platform: return -ENXIO for missing GpioInt

Merge tag 'tty-5.3-rc4' of git://git./linux/kernel/git/gregkh/tty

Pull tty fix from Greg KH:
 "Here is a single tty kgdb fix for 5.3-rc4.

  It fixes an annoying log message that has caused kdb to become
  useless. It's another fallout from commit ddde3c18b700 ("vt: More
  locking checks") which tries to enforce locking checks more strictly
  in the tty layer, unfortunatly when kdb is stopped, there's no need
  for locks :)

  This patch has been linux-next for a while with no reported issues"

* tag 'tty-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  kgdboc: disable the console lock when in kgdb

Merge tag 'staging-5.3-rc4' of git://git./linux/kernel/git/gregkh/staging

Pull staging / IIO driver fixes from Greg KH:
 "Here are some small staging and IIO driver fixes for 5.3-rc4.

  Nothing major, just resolutions for a number of small reported issues,
  full details in the shortlog.

  All have been in linux-next for a while with no reported issues"

* tag 'staging-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: adc: gyroadc: fix uninitialized return code
  docs: generic-counter.rst: fix broken references for ABI file
  staging: android: ion: Bail out upon SIGKILL when allocating memory.
  Staging: fbtft: Fix GPIO handling
  staging: unisys: visornic: Update the description of 'poll_for_irq()'
  staging: wilc1000: flush the workqueue before deinit the host
  staging: gasket: apex: fix copy-paste typo
  Staging: fbtft: Fix reset assertion when using gpio descriptor
  Staging: fbtft: Fix probing of gpio descriptor
  iio: imu: mpu6050: add missing available scan masks
  iio: cros_ec_accel_legacy: Fix incorrect channel setting
  IIO: Ingenic JZ47xx: Set clock divider on probe
  iio: adc: max9611: Fix misuse of GENMASK macro

Merge tag 'usb-5.3-rc4' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 5.3-rc4.

  The "biggest" one here is moving code from one file to another in
  order to fix a long-standing race condition with the creation of sysfs
  files for USB devices. Turns out that there are now userspace tools
  out there that are hitting this long-known bug, so it's time to fix
  them. Thankfully the tool-maker in this case fixed the issue :)

  The other patches in here are all fixes for reported issues. Now that
  syzbot knows how to fuzz USB drivers better, and is starting to now
  fuzz the userspace facing side of them at the same time, there will be
  more and more small fixes like these coming, which is a good thing.

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: setup authorized_default attributes using usb_bus_notify
  usb: iowarrior: fix deadlock on disconnect
  Revert "USB: rio500: simplify locking"
  usb: usbfs: fix double-free of usb memory upon submiturb error
  usb: yurex: Fix use-after-free in yurex_delete
  usb: typec: tcpm: Ignore unsupported/unknown alternate mode requests
  xhci: Fix NULL pointer dereference at endpoint zero reset.
  usb: host: xhci-rcar: Fix timeout in xhci_suspend()
  usb: typec: ucsi: ccg: Fix uninitilized symbol error
  usb: typec: tcpm: remove tcpm dir if no children
  usb: typec: tcpm: free log buf memory when remove debug file
  usb: typec: tcpm: Add NULL check before dereferencing config

Merge tag 'pinctrl-v5.3-2' of git://git./linux/kernel/git/linusw/linux-pinctrl

Pull pin control fixes from Linus Walleij:

 - Delay acquisition of regmaps in the Aspeed G5 driver.

 - Make a symbol static to reduce compiler noise.

* tag 'pinctrl-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: aspeed: Make aspeed_pinmux_ips static
  pinctrl: aspeed-g5: Delay acquisition of regmaps

Merge tag 'powerpc-5.3-4' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fix from Michael Ellerman:
 "Just one fix, a revert of a commit that was meant to be a minor
  improvement to some inline asm, but ended up having no real benefit
  with GCC and broke booting 32-bit machines when using Clang.

  Thanks to: Arnd Bergmann, Christophe Leroy, Nathan Chancellor, Nick
  Desaulniers, Segher Boessenkool"

* tag 'powerpc-5.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  Revert "powerpc: slightly improve cache helpers"

Merge tag 'Wimplicit-fallthrough-5.3-rc4' of git://git./linux/kernel/git/gustavoars/linux

Pull fall-through fixes from Gustavo A. R. Silva:
 "Mark more switch cases where we are expecting to fall through, fixing
  fall-through warnings in arm, sparc64, mips, i386 and s390"

* tag 'Wimplicit-fallthrough-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  ARM: ep93xx: Mark expected switch fall-through
  scsi: fas216: Mark expected switch fall-throughs
  pcmcia: db1xxx_ss: Mark expected switch fall-throughs
  video: fbdev: omapfb_main: Mark expected switch fall-throughs
  watchdog: riowd: Mark expected switch fall-through
  s390/net: Mark expected switch fall-throughs
  crypto: ux500/crypt: Mark expected switch fall-throughs
  watchdog: wdt977: Mark expected switch fall-through
  watchdog: scx200_wdt: Mark expected switch fall-through
  watchdog: Mark expected switch fall-throughs
  ARM: signal: Mark expected switch fall-through
  mfd: omap-usb-host: Mark expected switch fall-throughs
  mfd: db8500-prcmu: Mark expected switch fall-throughs
  ARM: OMAP: dma: Mark expected switch fall-throughs
  ARM: alignment: Mark expected switch fall-throughs
  ARM: tegra: Mark expected switch fall-through
  ARM/hw_breakpoint: Mark expected switch fall-throughs

Merge tag 'kbuild-fixes-v5.3-3' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - revive single target %.ko

 - do not create built-in.a where it is unneeded

 - do not create modules.order where it is unneeded

 - show a warning if subdir-y/m is used to visit a module Makefile

* tag 'kbuild-fixes-v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: show hint if subdir-y/m is used to visit module Makefile
  kbuild: generate modules.order only in directories visited by obj-y/m
  kbuild: fix false-positive need-builtin calculation
  kbuild: revive single target %.ko