Paul Fulghum [Tue, 22 Jul 2008 10:23:24 +0000 (11:23 +0100)]
synclink_gt fix locking in error path of rx enable
Fix locking in error path of rx_enable() introduced by
synclink_gt-add-rx-dma-buffer-fill-level-control patch.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:22:14 +0000 (11:22 +0100)]
synclink_gt: add rx DMA buffer fill level control
Add run time control for receive DMA buffer fill level to allow
application to control receive latency when using stream oriented serial
protocols that pass receive data to application only after a DMA buffer
fills. This was previously a compile time option, but run time control is
needed when application changes data rate (and latency requirements) or
uses different data rates on different ports.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:22:04 +0000 (11:22 +0100)]
synclink_gt: leave transmitter in reset state after configuration
Leave the transmitter in reset state after configuration so that transmit
signal is held at mark until transmitter is explicitly enabled by
application, otherwise transmitter sends idle pattern.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:21:55 +0000 (11:21 +0100)]
synclink_gt: improve TIOCOUTQ accuracy
Improve the accuracy of TIOCOUTQ value as implemented in chars_in_buffer()
method by walking and counting tx DMA buffers, reading controller tx FIFO
level and accounting for controller tx shift register. The greatly
improves application control of transmit latency at lower data rates.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:21:39 +0000 (11:21 +0100)]
synclink_gt: add serial bit order control
Add control of hardware serial bit order between LSB first
(default/standard) and MSB first.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:21:28 +0000 (11:21 +0100)]
synclink_gt: improve and simplify write method
Improve write method by allowing multiple HDLC frames to be loaded into tx
DMA buffer ring for continuous frame transmission. This simplifies the
transmit code by using the common procedures for all serial protocols.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Tue, 22 Jul 2008 10:21:19 +0000 (11:21 +0100)]
n_hdlc: honor O_NONBLOCK on write
Make n_hdlc line discipline honor the O_NONBLOCK file flag on write.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 22 Jul 2008 10:21:07 +0000 (11:21 +0100)]
serial: 8250: fix shared interrupts issues with SMP and RT kernels
With SMP kernels _irqsave spinlock disables only local interrupts, while
the shared serial interrupt could be assigned to the CPU that is not
currently starting up the serial port.
This might cause issues because serial8250_startup() routine issues
IRQ-triggering operations before registering the port in the IRQ chain
(though, this is fine to do and done explicitly because we don't want to
process any interrupts on the port startup).
With RT kernels and preemptable hardirqs, _irqsave spinlock does not
disable local hardirqs, and the bug could be reproduced much easily:
$ cat /dev/ttyS0 &
$ cat /dev/ttyS1
irq 42: nobody cared (try booting with the "irqpoll" option)
Call Trace:
[
C0475EB0] [
C0008A98] show_stack+0x4c/0x1ac (unreliable)
[
C0475EF0] [
C004BBD4] __report_bad_irq+0x34/0xb8
[
C0475F10] [
C004BD38] note_interrupt+0xe0/0x308
[
C0475F50] [
C004B09C] thread_simple_irq+0xdc/0x104
[
C0475F70] [
C004B3FC] do_irqd+0x338/0x3c8
[
C0475FC0] [
C00398E0] kthread+0xf8/0x100
[
C0475FF0] [
C0011FE0] original_kernel_thread+0x44/0x60
handlers:
[<
c02112c4>] (serial8250_interrupt+0x0/0x138)
Disabling IRQ #42
After this, all serial ports on the given IRQ are non-functional.
To fix the issue we should explicitly disable shared IRQ before
issuing any IRQ-triggering operations.
I also changed spin_lock_irqsave to the ordinary spin_lock, since it
seems to be safe: chain does not contain new port (yet), thus nobody
will interfere us from the ISRs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 22 Jul 2008 10:20:45 +0000 (11:20 +0100)]
Fix the epca driver to permit epca_setup() to be invoked from the kernel cmdline
Fix the epca driver to call epca_setup() if digiepca=xxx is included on the
command line and the epca driver is built in.
epca_setup() used to be called from init/main.c in 2.2 kernels, but somewhere
along the way that call was removed but not replaced.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Tue, 22 Jul 2008 10:20:34 +0000 (11:20 +0100)]
Char: mxser, add CP-102UF support
Add support for CP-102UF moxa card (update to 1.12 original driver) and
increment this driver version.
(Somewhat reworked by alan@redhat.com to merge in with other patches)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:19:05 +0000 (11:19 +0100)]
specialix: restore driver using new break functionality
Use the hardware break support on the specialix driver
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 22 Jul 2008 10:18:43 +0000 (11:18 +0100)]
Fix the (i)Stallion driver's putchar() and break_ctl() ops
Fix the Stallion driver's putchar() and break_ctl() ops and iStallion's
putchar() to return values.
Is it actually possible for putchar() or break_ctl() to be called with tty ==
NULL or can the check be discarded?
Should stl_write() be returning 0 if tty->driver_data is NULL or tx.buf is
NULL? Is this even possible?
I've made Stallion's functions return -EINVAL as stli_breakctl() if the checks
fail.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:18:30 +0000 (11:18 +0100)]
riscom8: Restore driver using new break functionality
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:18:21 +0000 (11:18 +0100)]
isicom: restore using hardware break support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:18:12 +0000 (11:18 +0100)]
epca: Restore driver
Convert the driver to use the added hardware break support
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:18:03 +0000 (11:18 +0100)]
tty: rework break handling
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:17:53 +0000 (11:17 +0100)]
tty: Mark unconverted drivers as BROKEN
Nobody seems to use these drivers anyway so if they want them they can
fix them up. I don't have the needed info to add break_ctl support to them.
Send patches if you don't like it.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:17:43 +0000 (11:17 +0100)]
mxser: remove dead code
Old style ioctl break code can go
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:17:32 +0000 (11:17 +0100)]
epca: Fix comments and move break
The ioctls it talks about are midlayer provided.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:17:16 +0000 (11:17 +0100)]
specialix: Code cleanups
Go through the inlines and other oddments that are iffy. Remove various bits
of dead code and bogus debug. Turn the crtsdts compile time option into a
runtime switch.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:17:05 +0000 (11:17 +0100)]
specialix: Tidy up coding style
Preparation for doing some real work on the driver. Do this first so we can
easily identify if the cleanups accidentally broke something
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:16:55 +0000 (11:16 +0100)]
tty: Split ldisc code into its own file
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:16:42 +0000 (11:16 +0100)]
io_edgeport: Fix various bogus returns to the tty layer
The edgeport reports negative error codes to functions that do not
expect them. This can cause ports to jam forever
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:16:34 +0000 (11:16 +0100)]
tty-usb-io_edgeport: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:16:21 +0000 (11:16 +0100)]
tty-usb-mos7720: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:16:12 +0000 (11:16 +0100)]
mos7840: remove loads of bogus assignments to status
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:16:03 +0000 (11:16 +0100)]
omninet: Use string flip functions
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:15:54 +0000 (11:15 +0100)]
tty-usb-omninet: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:15:45 +0000 (11:15 +0100)]
tty-usb-option: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:15:36 +0000 (11:15 +0100)]
tty-usb-oti6858: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:15:26 +0000 (11:15 +0100)]
tty-usb-safe-serial: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:15:17 +0000 (11:15 +0100)]
tty-usb-ti-usb: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:15:08 +0000 (11:15 +0100)]
tty-usb-spcp8x5: Minor coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:14:59 +0000 (11:14 +0100)]
tty-usb-sierra: Coding style - minor
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:14:49 +0000 (11:14 +0100)]
tty-usb-pl2303: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:14:40 +0000 (11:14 +0100)]
mct_u232: Use flip buffer functions
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:14:30 +0000 (11:14 +0100)]
tty-usb-mct-u232: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:14:22 +0000 (11:14 +0100)]
kobil_sct: Fix ioctls
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:14:10 +0000 (11:14 +0100)]
tty-usb-kobil-sct: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:14:00 +0000 (11:14 +0100)]
tty-usb-kl5kusb105: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:13:51 +0000 (11:13 +0100)]
keyspan_pda: Use string flip functions
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:13:42 +0000 (11:13 +0100)]
tty-usb-keyspan-pda: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:13:32 +0000 (11:13 +0100)]
keyspan: Use string flip functions when possible
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:13:08 +0000 (11:13 +0100)]
tty-usb-keyspan: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:12:59 +0000 (11:12 +0100)]
tty-usb-iuu-phoenix: Clean up to coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:12:51 +0000 (11:12 +0100)]
tty-usb-ipw: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:12:41 +0000 (11:12 +0100)]
ipaq: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:12:33 +0000 (11:12 +0100)]
io_ti: Minor coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:12:24 +0000 (11:12 +0100)]
usb-serial: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:12:15 +0000 (11:12 +0100)]
tty-usb-visor: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:12:05 +0000 (11:12 +0100)]
tty-usb-hp4x: Fix overlong line
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:11:55 +0000 (11:11 +0100)]
tty-usb-generic: Code cleanup
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:11:44 +0000 (11:11 +0100)]
garmin_gps: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:11:34 +0000 (11:11 +0100)]
funsoft: Switch to linux/uaccess
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:11:23 +0000 (11:11 +0100)]
ftdi_sio: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:11:11 +0000 (11:11 +0100)]
empeg: Coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:11:02 +0000 (11:11 +0100)]
digi_acceleport: coding style
Code tidy
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:10:53 +0000 (11:10 +0100)]
usb-cypress: There is no 0 case to go with CS5/6/7/8 so remove the test
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:10:36 +0000 (11:10 +0100)]
cypress_m8: coding style
Coding style clean ups
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:10:27 +0000 (11:10 +0100)]
cyberjack: Coding style
Coding style fixups
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:10:17 +0000 (11:10 +0100)]
cp2101: coding style
Bring up to coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:10:08 +0000 (11:10 +0100)]
tty-usb-console: Fix termios
Setting CFLAG bits is all well and good but you must sort out ispeed and
ospeed properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:09:57 +0000 (11:09 +0100)]
tty-usb-console: tidy the USB console code
Code tidy
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:09:48 +0000 (11:09 +0100)]
usb-serial-bus: tidy coding style
Tidy up
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:09:39 +0000 (11:09 +0100)]
belkin_sa: clean up code
Coding style tidy up for belkin_sa
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:09:29 +0000 (11:09 +0100)]
whiteheat: fix bugs found in the tidy and audit
Termios tidy up, plus fix break and DTR.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:09:16 +0000 (11:09 +0100)]
whiteheat: coding style
Bring ezusb and whiteheat into line with the coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:09:07 +0000 (11:09 +0100)]
usb_serial: API all change
USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.
So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.
Longer term we need a proper tty as console abstraction
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 22 Jul 2008 10:08:53 +0000 (11:08 +0100)]
ttydev: Fix up compile failures in the PPC build
Fix up a couple of reported merge problems
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mathieu Desnoyers [Mon, 21 Jul 2008 21:21:38 +0000 (14:21 -0700)]
markers: fix duplicate modpost entry
When a kernel was rebuilt, the previous Module.markers was not cleared.
It caused markers with different format strings to appear as duplicates
when a markers was changed. This problem is present since
scripts/mod/modpost.c started to generate Module.markers, commit
b2e3e658b344c6bcfb8fb694100ab2f2b5b2edb0
It therefore applies to 2.6.25, 2.6.26 and linux-next.
I merely merged the patches from Roland, Wenji and Takashi here.
Credits to
Roland McGrath <roland@redhat.com>
Wenji Huang <wenji.huang@oracle.com>
and
Takashi Nishiie <t-nishiie@np.css.fujitsu.com>
for providing the individual fixes.
- Changelog :
- Integrated Takashi's Makefile modification to clear Module.markers upon
make clean.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Roland McGrath <roland@redhat.com>
Cc: Wenji Huang <wenji.huang@oracle.com>
Cc: Takashi Nishiie <t-nishiie@np.css.fujitsu.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atsushi Nemoto [Mon, 21 Jul 2008 21:21:37 +0000 (14:21 -0700)]
Fix build on COMPAT platforms when CONFIG_EPOLL is disabled
Add missing cond_syscall() entry for compat_sys_epoll_pwait.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rajiv Andrade [Mon, 21 Jul 2008 21:21:37 +0000 (14:21 -0700)]
tpm: MAINTAINERS whitespace fix and email addresses addition
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Mon, 21 Jul 2008 21:21:36 +0000 (14:21 -0700)]
proc: fix /proc/*/pagemap some more
struct pagemap_walk was placed on stack, some hooks are initialized, the
rest (->pgd_entry, ->pud_entry, ->pte_entry) are valid but junk.
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Vegard Nossum" <vegard.nossum@gmail.com>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miao Xie [Mon, 21 Jul 2008 21:21:35 +0000 (14:21 -0700)]
cpusets: fix wrong domain attr updates
Fix wrong domain attr updates, or we will always update the first sched
domain attr.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Mon, 21 Jul 2008 21:21:34 +0000 (14:21 -0700)]
gpio: pcf857x: add lock and handle more chips
Two small updates to the pcf857x driver: (a) the max732[89] chips are
also second sources for the pcf8574/a, and (b) add a mutex to prevent
trashing the cached state. Adding the lock is effectively a bugfix,
although it seems unlikely that anyone would have run into the issue it
protects against.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Juergen Beisert [Mon, 21 Jul 2008 21:21:34 +0000 (14:21 -0700)]
gpio: gpio driver for max7301 SPI GPIO expander
Maxim's MAX7301 is an SPI GPIO expander with 28 GPIOs. Note: MAX7301's
interrupt feature is not supported yet.
[akpm@linux-foundation.org: coding-style fixes]
[g.liakhovetski@pengutronix.de: Fix inaccuracies in comments, check spi_setup()
return code, mask off high byte in max7301_read()]
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John Reiser [Mon, 21 Jul 2008 21:21:32 +0000 (14:21 -0700)]
execve filename: document and export via auxiliary vector
The Linux kernel puts the filename argument of execve() into the new
address space. Many developers are surprised to learn this. Those who
know and could use it, object "But it's not documented."
Those who want to use it dislike the expression
(char *)(1+ strlen(env[-1+ n_env]) + env[-1+ n_env])
because it requires locating the last original environment variable,
and assumes that the filename follows the characters.
This patch documents the insertion of the filename, and makes it easier
to find by adding a new tag AT_EXECFN in the ElfXX_auxv_t; see <elf.h>.
In many cases readlink("/proc/self/exe",) gives the same answer. But if
all the original pages get unmapped, then the kernel erases the symlink
for /proc/self/exe. This can happen when a program decompressor does a
good job of cleaning up after uncompressing directly to memory, so that
the address space of the target program looks the same as if compression
had never happened. One example is http://upx.sourceforge.net .
One notable use of the underlying concept (what path containED the
executable) is glibc expanding $ORIGIN in DT_RUNPATH. In practice for
the near term, it may be a good idea for user-mode code to use both
/proc/self/exe and AT_EXECFN as fall-back methods for each other.
/proc/self/exe can fail due to unmapping, AT_EXECFN can fail because it
won't be present on non-new systems. The auxvec or {AT_EXECFN}.d_val
also can get overwritten, although in nearly all cases this would be the
result of a bug.
The runtime cost is one NEW_AUX_ENT using two words of stack space. The
underlying value is maintained already as bprm->exec; setup_arg_pages()
in fs/exec.c slides it for stack_shift, etc.
Signed-off-by: John Reiser <jreiser@BitWagon.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 21 Jul 2008 22:42:20 +0000 (15:42 -0700)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (100 commits)
usb-storage: revert DMA-alignment change for Wireless USB
USB: use reset_resume when normal resume fails
usb_gadget: composite cdc gadget fault handling
usb gadget: minor USBCV fix for composite framework
USB: Fix bug with byte order in isp116x-hcd.c fio write/read
USB: fix double kfree in ipaq in error case
USB: fix build error in cdc-acm for CONFIG_PM=n
USB: remove board-specific UP2OCR configuration from pxa27x-udc
USB: EHCI: Reconciling USB register differences on MPC85xx vs MPC83xx
USB: Fix pointer/int cast in USB devio code
usb gadget: g_cdc dependso on NET
USB: Au1xxx-usb: suspend/resume support.
USB: Au1xxx-usb: clean up ohci/ehci bus glue sources.
usbfs: don't store bad pointers in registration
usbfs: fix race between open and unregister
usbfs: simplify the lookup-by-minor routines
usbfs: send disconnect signals when device is unregistered
USB: Force unbinding of drivers lacking reset_resume or other methods
USB: ohci-pnx4008: I2C cleanups and fixes
USB: debug port converter does not accept more than 8 byte packets
...
Alan Stern [Mon, 30 Jun 2008 17:39:59 +0000 (13:39 -0400)]
usb-storage: revert DMA-alignment change for Wireless USB
This patch (as1110) reverts an earlier patch meant to help with
Wireless USB host controllers. These controllers can have bulk
maxpacket values larger than 512, which puts unusual constraints on
the sizes of scatter-gather list elements. However it turns out that
the block layer does not provide the support we need to enforce these
constraints; merely changing the DMA alignment mask doesn't help.
Hence there's no reason to keep the original patch. The Wireless USB
problem will have to be solved a different way.
In addition, there is a reason to get rid of the earlier patch. By
dereferencing a pointer stored in the ep_in array of struct
usb_device, the current code risks an invalid memory access when it
runs concurrently with device removal. The members of that array are
cleared before the driver's disconnect method is called, so it should
not try to use them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 30 Jun 2008 15:14:43 +0000 (11:14 -0400)]
USB: use reset_resume when normal resume fails
This patch (as1109b) makes USB-Persist more resilient to errors. With
the current code, if a normal resume fails, it's an unrecoverable
error. With the patch, if a normal resume fails (and if the device is
enabled for USB-Persist) then a reset-resume is tried.
This fixes the problem reported in Bugzilla #10977.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 1 Jul 2008 20:18:20 +0000 (13:18 -0700)]
usb_gadget: composite cdc gadget fault handling
These two fixes ensure the new "CDC Composite Device" gadget
fails cleanly when it's loaded on hardware that can't support
this particular gadget driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Lopo [Tue, 1 Jul 2008 20:14:17 +0000 (13:14 -0700)]
usb gadget: minor USBCV fix for composite framework
Fill in a reserved/unused device qualifier field to ensure that
the USBCV tests will always pass.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Julien May [Fri, 27 Jun 2008 13:01:18 +0000 (15:01 +0200)]
USB: Fix bug with byte order in isp116x-hcd.c fio write/read
URB payload data are transfered in wrong byte order on a big endinan
architecture (AVR32).
Signed-off-by: Julien May <mailinglist@miromico.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Mon, 30 Jun 2008 12:33:57 +0000 (14:33 +0200)]
USB: fix double kfree in ipaq in error case
in the error case the ipaq driver leaves a dangling pointer to already
freed memory that will be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 1 Jul 2008 17:10:08 +0000 (19:10 +0200)]
USB: fix build error in cdc-acm for CONFIG_PM=n
Here's the fix. cdc-wdm has the same problem. The fix is the same.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Ribeiro [Wed, 2 Jul 2008 02:09:27 +0000 (23:09 -0300)]
USB: remove board-specific UP2OCR configuration from pxa27x-udc
Remove the board-specific UP2OCR configuration from the
pxa27x-udc driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Srikanth Srinivasan [Wed, 2 Jul 2008 07:14:33 +0000 (02:14 -0500)]
USB: EHCI: Reconciling USB register differences on MPC85xx vs MPC83xx
A couple of USB register initializations had to be changed on MPC85xx
platforms. This is due to the internal SoC buses being different on
MPC83xx SoCs vs MPC85xx SoCs.
We currently handle this via an ifdef since 83xx and 85xx are mutually
exclusive kernel builds.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Howells [Wed, 2 Jul 2008 11:28:55 +0000 (12:28 +0100)]
USB: Fix pointer/int cast in USB devio code
Fix pointer/int cast in USB devio code, and thus avoid a compiler warning.
A void* data argument passed to bus_find_device() and thence to match_devt()
is used to carry a 32-bit datum. However, casting directly between a u32 and
a pointer is not permitted - there must be an intermediate cast via (unsigned)
long.
This was introduced by the following patch:
commit
94b1c9fa060ece2c8f080583beb6cc6008e41413
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Tue Jun 24 14:47:12 2008 -0400
usbfs: simplify the lookup-by-minor routines
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Thu, 3 Jul 2008 21:44:59 +0000 (14:44 -0700)]
usb gadget: g_cdc dependso on NET
g_cdc needs to depend on NET, otherwise net-related build errors happen:
ERROR: "netif_carrier_on" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "netif_carrier_off" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "netif_rx" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "alloc_etherdev_mq" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "free_netdev" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "register_netdev" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "print_mac" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "dev_kfree_skb_any" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "__alloc_skb" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "eth_type_trans" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "unregister_netdev" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "__netif_schedule" [drivers/usb/gadget/g_cdc.ko] undefined!
ERROR: "skb_put" [drivers/usb/gadget/g_cdc.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Manuel Lauss [Mon, 23 Jun 2008 07:09:37 +0000 (09:09 +0200)]
USB: Au1xxx-usb: suspend/resume support.
Copy the OHCI/EHCI PM callbacks of the PCI implementation since
they work equally well on Au1xxx hardware.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Manuel Lauss [Mon, 23 Jun 2008 07:08:29 +0000 (09:08 +0200)]
USB: Au1xxx-usb: clean up ohci/ehci bus glue sources.
- Fold multiple probe/remove callbacks into one function;
- minor style fixes, no functional changes.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 24 Jun 2008 18:47:29 +0000 (14:47 -0400)]
usbfs: don't store bad pointers in registration
This patch (as1107) fixes a small bug in the usbfs registration and
unregistration code. It avoids leaving an error value stored in the
device's usb_classdev field and it avoids trying to unregister a NULL
pointer. (It also fixes a rather extreme overuse of whitespace.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 24 Jun 2008 18:47:19 +0000 (14:47 -0400)]
usbfs: fix race between open and unregister
This patch (as1106) fixes a race between opening and unregistering
device files in usbfs. The current code drops its reference to the
device and then reacquires it, ignoring the possibility that the
device structure might have been removed in the meantime. It also
doesn't check whether the device is already in the NOTATTACHED state
when the file is opened.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 24 Jun 2008 18:47:12 +0000 (14:47 -0400)]
usbfs: simplify the lookup-by-minor routines
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 24 Jun 2008 18:47:04 +0000 (14:47 -0400)]
usbfs: send disconnect signals when device is unregistered
USB device files are accessible in two ways: as files in usbfs and as
character device nodes. The two paths are supposed to behave
identically, but they don't. When the underlying USB device is
unplugged, disconnect signals are sent to processes with open usbfs
files (if they requested these signals) but not to processes with open
device node files.
This patch (as1104) fixes the bug by moving the disconnect-signalling
code into a common subroutine which is called from both paths.
Putting this subroutine in devio.c removes the only out-of-file
reference to struct dev_state, and so the structure's declaration can
be moved from usb.h into devio.c.
Finally, the new subroutine performs one extra action: It kills all
the outstanding async URBs. (I'd kill the outstanding synchronous
URBs too, if there was any way to do it.) In the past this hasn't
mattered much, because devices were unregistered from usbfs only
when they were disconnected. But now the unregistration can also
occur whenever devices are unbound from the usb_generic driver. At
any rate, killing URBs when a device is unregistered from usbfs seems
like a good thing to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 23 Jun 2008 20:00:40 +0000 (16:00 -0400)]
USB: Force unbinding of drivers lacking reset_resume or other methods
This patch (as1024) takes care of a FIXME issue: Drivers that don't
have the necessary suspend, resume, reset_resume, pre_reset, or
post_reset methods will be unbound and their interface reprobed when
one of the unsupported events occurs.
This is made slightly more difficult by the fact that bind operations
won't work during a system sleep transition. So instead the code has
to defer the operation until the transition ends.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Wed, 18 Jun 2008 12:46:27 +0000 (14:46 +0200)]
USB: ohci-pnx4008: I2C cleanups and fixes
Various cleanups and fixes to the i2c code in ohci-pnx4008:
* Delete empty isp1301_command. The i2c driver command implementation
is optional, so there's no point in providing an empty
implementation.
* Give a name to isp1301_driver. I'm surprised that i2c-core accepted
to register this driver at all. I've chosen "isp1301_pnx" as the
name, because it's not a generic ISP1301 driver (much like the
isp1301_omap driver.) We might want to make the name even more
specific (but "isp1301_ohci_pnx4008" doesn't fit.)
* The ISP1301 is definitely not a hardware monitoring device.
* Fix a memory leak on failure in isp1301_attach. If
i2c_attach_client fails, the client is not registered so
isp1301_detach is never called and the i2c_client memory is lost.
* Use strlcpy instead of strcpy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Aleksey Gorelov [Thu, 19 Jun 2008 22:22:17 +0000 (15:22 -0700)]
USB: debug port converter does not accept more than 8 byte packets
USB debug port only supports 8 byte rx/tx packets. Although spec implies that
"if a packet larger than eight bytes is received from the remote computer, the
device must break the larger packet into eight-byte packets before sending the
data to the Debug Port", the real PLX NET20DC device does not handle it right -
data is corrupted on debug port end if serial interface sends >8 byte urbs.
Patch below fixes the issue by limiting tx urb to 8 byte.
Signed off by: Aleks Gorelov <dared1st@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Wed, 25 Jun 2008 12:17:16 +0000 (14:17 +0200)]
USB: fix disconnect bug in cdc-acm
cdc-acm must give up secondary interfaces if the primary is disconnected
and vice versa. This wasn't done correctly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Wed, 25 Jun 2008 11:32:49 +0000 (13:32 +0200)]
USB: fix usb serial pm counter decrement for disconnected interfaces
usb serial decrements the pm counter even if an interface has been
disconnected. If it was a logical disconnect the interface may belong
already to another driver. This patch introduces a check for disconnected
interfaces.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / platform / upstream / kernel-adaptation-pc.git / log