phy: Add suspend/resume support to SMSC PHYs

All supported SMSC PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic genphy_{suspend,resume}
functions.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylib: Fix oops in suspend/resume paths

Suspend/resume routines check for phydrv != NULL, but that is
wrong because "phydrv" comes from container_of(drv). If drv is NULL,
then container_of(drv) will return non-NULL result, and the checks
won't work.

The Freescale TBI PHYs are driver-less, so "drv" is NULL, and that
leads to the following oops:

Unable to handle kernel paging request for data at address 0xffffffe4
Faulting instruction address: 0xc0215554
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0215554] mdio_bus_suspend+0x34/0x70
LR [c01cc508] suspend_device+0x258/0x2bc
Call Trace:
[cfad3da0] [cfad3db8] 0xcfad3db8 (unreliable)
[cfad3db0] [c01cc508] suspend_device+0x258/0x2bc
[cfad3dd0] [c01cc62c] dpm_suspend+0xc0/0x140
[cfad3e20] [c01cc6f4] device_suspend+0x48/0x5c
[cfad3e40] [c0068dd8] suspend_devices_and_enter+0x8c/0x148
[cfad3e60] [c00690f8] enter_state+0x100/0x118
[cfad3e80] [c00691c0] state_store+0xb0/0xe4
[cfad3ea0] [c018c938] kobj_attr_store+0x24/0x3c
[cfad3eb0] [c00ea9a8] flush_write_buffer+0x58/0x7c
[cfad3ed0] [c00eadf0] sysfs_write_file+0x58/0xa0
[cfad3ef0] [c009e810] vfs_write+0xb4/0x16c
[cfad3f10] [c009ed40] sys_write+0x4c/0x90
[cfad3f40] [c0014954] ret_from_syscall+0x0/0x38
[...]

This patch fixes the issue, plus removes unneeded parentheses
and fixes indentation level in mdio_bus_suspend().

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Version

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: loopback test failure

A link change interrupt might be queued and activated after the loopback was set
and it will cause the loopback to fail. The PHY lock should be kept until the
loopback test is over.

That implies that the bnx2x_test_link should used within the loopback function
and not bnx2x_wait_for_link since that function also takes the PHY link

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Missing rmb when waiting for FW response

Waiting for the FW to response requires a memory barrier

Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Calling napi_del

rmmod might hang without this patch since the reference counter is not going
down

Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Carrier off first call

Call carrier off should not be called after register_netdev since after
register netdev open can be called at any time followed by an interrupt that
will set it to carrier_on and the probe will resume control and set it to off

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Handling load failures

Failures on load were not handled correctly - separate the flow to handle

different failures

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Disable napi

Calling napi disabled unconditionally at netif stop

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Reset HW before use

To avoid complications, make sure that the HW is in reset (as it should be)
before trying to take it out of reset. In normal flows, the HW is indeed in rest
so this should have no effect

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

iwlwifi: return NETDEV_TX_OK from _tx ops

be consistent with mac80211 drivers and return correct return code.
NETDEV_TX_OK is 0, but we need to be consistent wrt formatting amongst
implementations

re: http://marc.info/?l=linux-wireless&m=123119327419865&w=2

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: adding Sitecom WL-603 (0df6:0036) to the USB id list

Giuseppe Cala <jiveaxe@gmail.com> (The second "a" in "Cala" should be
a grave, U+00E0) reported success on zd1211-devs@lists.sourceforge.net.
The chip info is:
zd1211b chip 0df6:0036 v4810 high 00-0c-f6 AL2230_RF pa0 g--N-

The Sitecom WL-603 is detected as a zd1211b with a AL2230 RF transceiver chip.

Signed-off-by: Giuseppe Cala <jiveaxe@gmail.com>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54usb: fix nasty use after free

In theory, the firmware acks the received a data frame, before signaling the driver to free it again.
However Artur Skawina <art.08.09@gmail.com> has shown that it can happen in reverse order as well.
This is very bad and could lead to memory corruptions, oopses and panics.

Thanks to Artur Skawina <art.08.09@gmail.com> for reporting and debugging this issue.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: more cryptographic accelerator fixes

If we let the firmware do the data encryption, we have to remove the ICV and
(M)MIC at the end of the frame before we can give it back to mac80211.
Or, these data frames have a few trailing bytes on cooked monitor interfaces.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: add missing break in eeprom parser

This patch fixes a obvious memory leak in the eeprom parser.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: use KERN_DEBUG for link status messages

KERN_INFO is too "loud" for messages that are generated by the ordinary
events, such as accociation.  Use of KERN_DEBUG is consistent with
mac80211.

Suggested by Michael Gilbert <michael.s.gilbert@gmail.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix TX rate short preamble detection

Mac80211 provides 2 structures to handle bitrates, namely
ieee80211_rate and ieee80211_tx_rate. To determine the short preamble
mode for an outgoing frame, the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE
must be checked on ieee80211_tx_rate and not ieee80211_rate (which rt2x00 did).

This fixes a regression which was triggered in 2.6.29-rcX as reported by Chris Clayton.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-By: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix slot time debug message

wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=) <something is missing here>

should be:

wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=00:01:aa:bb:cc:dd)

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: move kmalloc(..., GFP_KERNEL) outside spinlock in orinoco_ioctl_set_genie

[   56.923623] BUG: sleeping function called from invalid context at /home/bor/src/linux-git/mm/slub.c:1599
[   56.923644] in_atomic(): 0, irqs_disabled(): 1, pid: 3031, name: wpa_supplicant
[   56.923656] 2 locks held by wpa_supplicant/3031:
[   56.923662]  #0:  (rtnl_mutex){--..}, at: [<c02abd1f>] rtnl_lock+0xf/0x20
[   56.923703]  #1:  (&priv->lock){++..}, at: [<dfc840c2>] orinoco_ioctl_set_genie+0x52/0x130 [orinoco]
[   56.923782] irq event stamp: 910
[   56.923788] hardirqs last  enabled at (909): [<c01957db>] __kmalloc+0x7b/0x140
[   56.923820] hardirqs last disabled at (910): [<c0309419>] _spin_lock_irqsave+0x19/0x80
[   56.923847] softirqs last  enabled at (880): [<c0124f54>] __do_softirq+0xc4/0x110
[   56.923865] softirqs last disabled at (871): [<c01049ae>] do_softirq+0x8e/0xe0
[   56.923895] Pid: 3031, comm: wpa_supplicant Not tainted 2.6.29-rc2-1avb #1
[   56.923905] Call Trace:
[   56.923919]  [<c01049ae>] ? do_softirq+0x8e/0xe0
[   56.923941]  [<c011ad12>] __might_sleep+0xd2/0x100
[   56.923952]  [<c0195837>] __kmalloc+0xd7/0x140
[   56.923963]  [<c030946a>] ? _spin_lock_irqsave+0x6a/0x80
[   56.923981]  [<dfc840e9>] ? orinoco_ioctl_set_genie+0x79/0x130 [orinoco]
[   56.923999]  [<dfc840c2>] ? orinoco_ioctl_set_genie+0x52/0x130 [orinoco]
[   56.924017]  [<dfc840e9>] orinoco_ioctl_set_genie+0x79/0x130 [orinoco]
[   56.924036]  [<c0209325>] ? copy_from_user+0x35/0x130
[   56.924061]  [<c02ffd96>] ioctl_standard_call+0x196/0x380
[   56.924085]  [<c029f945>] ? __dev_get_by_name+0x85/0xb0
[   56.924096]  [<c02ff88f>] wext_handle_ioctl+0x14f/0x230
[   56.924113]  [<dfc84070>] ? orinoco_ioctl_set_genie+0x0/0x130 [orinoco]
[   56.924132]  [<c02a3da5>] dev_ioctl+0x495/0x570
[   56.924155]  [<c0293e05>] ? sys_sendto+0xa5/0xd0
[   56.924171]  [<c0142fe8>] ? mark_held_locks+0x48/0x90
[   56.924183]  [<c0292880>] ? sock_ioctl+0x0/0x280
[   56.924193]  [<c029297d>] sock_ioctl+0xfd/0x280
[   56.924203]  [<c0292880>] ? sock_ioctl+0x0/0x280
[   56.924235]  [<c01a51d0>] vfs_ioctl+0x20/0x80
[   56.924246]  [<c01a53e2>] do_vfs_ioctl+0x72/0x570
[   56.924257]  [<c0293e62>] ? sys_send+0x32/0x40
[   56.924268]  [<c02947c0>] ? sys_socketcall+0x1d0/0x2a0
[   56.924280]  [<c010339f>] ? sysenter_exit+0xf/0x16
[   56.924292]  [<c01a5919>] sys_ioctl+0x39/0x70
[   56.924302]  [<c0103371>] sysenter_do_call+0x12/0x31

Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: decrement ref count to netdev after launching mesh discovery

After launching mesh discovery in tx path, reference count was not being
decremented.  This was preventing module unload.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

usb/mcs7830: Don't use buffers from stack for USB transfers

mcs7830_set_reg() and mcs7830_get_reg() are called with buffers
from stack which must not be used directly for USB transfers.
This causes corruption of the stack particulary on non x86
architectures because DMA may be used for these transfers.

Signed-off-by: Christian Eggers <christian.eggers@kathrein.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

usbnet: allow type check of devdbg arguments in non-debug build

Improve usbnet's devdbg to always type-check diagnostic arguments,
like dev_dbg (device.h).  This makes no change to the resulting size of
usbnet modules.

This patch also removes an #ifdef DEBUG directive from rndis_wlan so
it's devdbg statements are always type-checked at compile time.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

netfilter: ctnetlink: fix scheduling while atomic

Caused by call to request_module() while holding nf_conntrack_lock.

Reported-and-tested-by: Kövesdi György <kgy@teledigit.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

gro: Fix merging of paged packets

The previous fix to paged packets broke the merging because it
reset the skb->len before we added it to the merged packet.  This
wasn't detected because it simply resulted in the truncation of
the packet while the missing bit is subsequently retransmitted.

The fix is to store skb->len before we clobber it.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

gro: Fix error handling on extremely short frags

When a frag is shorter than an Ethernet header, we'd return a
zeroed packet instead of aborting.  This patch fixes that.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

gro: Fix handling of complete checksums in IPv6

We need to perform skb_postpull_rcsum after pulling the IPv6
header in order to maintain the correctness of the complete
checksum.

This patch also adds a missing iph reload after pulling.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

via-velocity: fix hot spin

while(--j >= 0) keeps spinning when j is unsigned:

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

myri10ge: don't forget pci_disable_device()

Don't forget to call pci_disable_device() in myri10ge_remove()
and when myri10ge_probe() fails.

By the way, update the copyright years.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET: net_namespace, fix lock imbalance

register_pernet_gen_subsys omits mutex_unlock in one fail path.
Fix it.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Revert "xfrm: For 32/64 compatability wrt. xfrm_usersa_info"

This reverts commit fc8c7dc1b29560c016a67a34ccff32a712b5aa86.

As indicated by Jiri Klimes, this won't work.  These numbers are
not only used the size validation, they are also used to locate
attributes sitting after the message.

Signed-off-by: David S. Miller <davem@davemloft.net>

wimax/i2400m: error paths that need to free an skb should use kfree_skb()

Roel Kluin reported a bug in two error paths where skbs were wrongly
being freed using kfree(). He provided a fix where it was replaced to
kfree_skb(), as it should be.

However, in i2400mu_rx(), the error path was missing returning an
indication of the failure. Changed to reset rx_skb to NULL and return
it to the caller, i2400mu_rxd(). It will be treated as a transient
error and just ignore the packet.

Depending on the buffering conditions inside the device, the data
packet might be dropped or the device will signal the host again for
data-ready-to-read and the host will retry.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv643xx_eth: prevent interrupt storm on ifconfig down

Contrary to what the docs say, the 'extended interrupt cause' bit in
the interrupt cause register (bit 1) appears to not be maskable on at
least some of the mv643xx_eth platforms, making writing zeroes to the
interrupt mask register but not the extended interrupt mask register
insufficient to stop interrupts from occuring.  Therefore, also write
zeroes to the extended interrupt mask register when shutting down the
port.

This fixes the interrupt storm seen on the Pegasos board when shutting
down the interface.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv643xx_eth: fix multicast filter programming

Commit 66e63ffbc04706568d8789cbb00eaa8ddbcae648 ("mv643xx_eth:
implement ->set_rx_mode()") cleaned up mv643xx_eth's multicast filter
programming, but broke it as well.

The non-special multicast filter table (for multicast addresses that
are not of the form 01:00:5e:00:00:xx) consists of 256 hash table
buckets organised as 64 32-bit words, where the 'accept' bits are
in the LSB of each byte, so in bits 24 16 8 0 of each 32-bit word.
The old code got this right, but the referenced commit broke this by
using bits 3 2 1 0 instead.  This commit fixes this up.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "mv643xx_eth: use longer DMA bursts".

This reverts commit cd4ccf76bfd2c36d351e68be7e6a597268f98a1a.

On the Pegasos board, we can't do DMA burst that are longer than
one cache line.  For now, go back to using 32 byte DMA bursts for
all mv643xx_eth platforms -- we can switch the ARM-based platforms
back to doing long 128 byte bursts in the next development cycle.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reported-by: Alan Curry <pacman@kosh.dhis.org>
Reported-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Fix data corruption when splicing from sockets.

The trick in socket splicing where we try to convert the skb->data
into a page based reference using virt_to_page() does not work so
well.

The idea is to pass the virt_to_page() reference via the pipe
buffer, and refcount the buffer using a SKB reference.

But if we are splicing from a socket to a socket (via sendpage)
this doesn't work.

The from side processing will grab the page (and SKB) references.
The sendpage() calls will grab page references only, return, and
then the from side processing completes and drops the SKB ref.

The page based reference to skb->data is not enough to keep the
kmalloc() buffer backing it from being reused.  Yet, that is
all that the socket send side has at this point.

This leads to data corruption if the skb->data buffer is reused
by SLAB before the send side socket actually gets the TX packet
out to the device.

The fix employed here is to simply allocate a page and copy the
skb->data bytes into that page.

This will hurt performance, but there is no clear way to fix this
properly without a copy at the present time, and it is important
to get rid of the data corruption.

With fixes from Herbert Xu.

Tested-by: Willy Tarreau <w@1wt.eu>
Foreseen-by: Changli Gao <xiaosuo@gmail.com>
Diagnosed-by: Willy Tarreau <w@1wt.eu>
Reported-by: Willy Tarreau <w@1wt.eu>
Fixed-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: Fix firmware loading

This patch modifies how the tg3 driver handles device firmware.

The patch starts by consolidating David Woodhouse's earlier patch under
the same name.  Specifically, the patch moves the request_firmware call
into a separate tg3_request_firmware() function and calls that function
from tg3_open() rather than tg3_init_one().

The patch then goes on to limit the number of devices that will make
request_firmware calls.  The original firmware patch unnecessarily
requested TSO firmware for devices that did not need it.  This patch
reduces the set of devices making TSO firmware patches to approximately
the following device set : 5703, 5704, and 5705.

Finally, the patch reduces the effects of a request_firmware() failure.
For those devices that are requesting TSO firmware, the driver will turn
off the TSO capability.  If TSO firmware becomes available at a later
time, the device can be closed and then opened again to reacquire the
TSO capability.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Fix usage of netif_*_all_queues() with netif_carrier_{off|on}()

netif_carrier_off() is sufficient to stop Tx into the driver.  Stopping the Tx
queues is redundant and unnecessary.  By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: fix tag stripping for VLAN ID 0

Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode.  VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid.  The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: fix dca issue with relaxed ordering turned on

The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints.  This patch forces RO not to be set for
descriptors as well as payload.  This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add debug info to track down GSO checksum bug

I'm trying to track down why people're hitting the checksum warning
in skb_gso_segment.  As the problem seems to be hitting lots of
people and I can't reproduce it or locate the bug, here is a patch
to print out more details which hopefully should help us to track
this down.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

korina: drop leftover assignment

As the assigned value is being overwritten shortly after, it can be
dropped and so the whole variable definition moved to the start of the
function.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

korina: adjust headroom for new skb's also

This is copy and paste from the original driver. As skb_reserve() is
also called within korina_alloc_ring() when initially allocating the
receive descriptors, the same should be done when allocating new space
after passing an skb to upper layers.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

korina: fix loop back of receive descriptors

After the last loop iteration, i has the value RC32434_NUM_RDS and
therefore leads to an index overflow when used afterwards to address the
last element. This is yet another another bug introduced when rewriting
parts of the driver for upstream preparation, as the original driver
used 'RC32434_NUM_RDS - 1' instead.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb3: Fix LRO misalignment

The lro manager's frag_align_pad setting was missing,
leading to misaligned access to the skb passed up
to the stack.

Tested-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

macb: avoid lockup when TGO during underrun

In rare cases when an underrun occur, all macb buffers where consumed
and the netif_queue was stopped infinitely. This happens then the TGO
(transfer ongoing) bit in the TSR is set (and UND). It seems like
clening up after the underrun makes the driver and the macb hardware
end up in an inconsistent state. The result of this is that in the
following calls to macb_tx no TX buffers are released -> the
netif_queue was stopped, and never woken up again.

The solution is to disable the transmitter, if TGO is set, before
clening up after the underrun, and re-enable the transmitter when the
cleaning up is done.

Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/9p: fid->fid is used uninitialized

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Version update

Updating the version and the year of updated files

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Barriers for the compiler

To make sure no swapping are made by the compiler, changed HAS_WORK to inline
functions and added all the necessary barriers

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Driver description update

The Driver supports the 57711 and 57711E as well but the description was out of
date

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Handling PHY FW load failure

If the default PHY version (0x4321) is read - the PHY FW load failed

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Legacy speeds autoneg failures

10M/100M autoneg was not establishing link.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Prevent self test loopback failures

Setting loopback requires time to take effect

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: 1G-10G toggling race

The HW should be configured so fast toggling between 1G and 10G will not be
missed. Make sure that the HW is re-configured in full

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Overstepping array bounds

If the page size is > 8KB this violation happens

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Block nvram access when the device is inactive

Don't dump eeprom when bnx2x adapter is down.  Running ethtool -e causes an eeh
without it when the device is down

Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Read chip ID

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Wrong HDR offset in CAM

Has a negative side effect when sending MAC update with no content (as done in
the self-test)

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Potential race after iSCSI boot

The lock was release too soon. Make sure the HW is marked as locked until the
boot driver was unloaded from FW perspective

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Handling probe failures

Failures in the probe not handled correctly - separate the flow to handle

different failures

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Free IRQ

Error check could result with not freeing the IRQ

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ehca: Use consistent types for ehca_plpar_hcall9()
  IB/ehca: Fix printk format warnings from u64 type change
  IPoIB: Do not print error messages for multicast join retries
  IB/mlx4: Fix memory ordering problem when posting LSO sends
  mlx4_core: Fix min() warning
  IPoIB: Fix deadlock between ipoib_open() and child interface create
  IPoIB: Fix hang in napi_disable() if P_Key is never found

Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  move wm8400-regulator's probe function to .devinit.text

dell_rbu: use scnprintf() instead of less secure sprintf()

Reading 0 bytes from /sys/devices/platform/dell_rbu/image_type or
/sys/devices/platform/dell_rbu/packet_size by an ordinary user causes an
oops.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

security: introduce missing kfree

Plug this leak.

Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: <stable@kernel.org>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

move wm8400-regulator's probe function to .devinit.text

A pointer to wm8400_regulator_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded.  Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.

An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Merge branches 'ehca', 'ipoib' and 'mlx4' into for-linus

IB/ehca: Use consistent types for ehca_plpar_hcall9()

ehca_plpar_hcall9() takes an unsigned long array, so make all callers
pass that in.  This fixes warnings introduced by commit fe333321
("powerpc: Change u64/s64 to a long long integer type"), which changed
u64 from unsigned long to unsigned long long.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/ehca: Fix printk format warnings from u64 type change

Commit fe333321 ("powerpc: Change u64/s64 to a long long integer
type") changed u64 from unsigned long to unsigned long long, which
means that printk formats for printing u64 values should use "ll"
instead of "l" to avoid warnings.  Fix all the places affected by this
in ehca.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

p54: fix p54_set_key's return code

p54 doesn't support AES-128-CMAC offload.

This patch will fix the noisy mac80211 warnings, when 802.11w is enabled:
mac80211-phy189: failed to set key (4, ff:ff:ff:ff:ff:ff) to hardware (-22)
mac80211-phy189: failed to set key (5, ff:ff:ff:ff:ff:ff) to hardware (-22)

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: set_tim must be atomic.

Fix for:

BUG: scheduling while atomic: named/2004/0x10000200
Pid: 2004, comm: named Not tainted 2.6.29-rc1-00271-ge9fa6b0 #45
Call Trace:
 [<c04d4ef7>] schedule+0x2a7/0x320
 [<c03aed74>] __alloc_skb+0x34/0x110
 [<c011f5b3>] __cond_resched+0x13/0x30
 [<c04d501d>] _cond_resched+0x2d/0x40
 [<c016d8c5>] kmem_cache_alloc+0x95/0xc0
 [<c016b8d4>] check_object+0xc4/0x230
 [<c03aed74>] __alloc_skb+0x34/0x110
 [<c02ede91>] p54_alloc_skb+0x71/0xf0
 [<c02ee36f>] p54_set_tim+0x3f/0xa0
 [<c04ae064>] sta_info_set_tim_bit+0x64/0x80
 [<c04c1017>] invoke_tx_handlers+0xd57/0xd80
 [<c016c397>] free_debug_processing+0x197/0x210
 [<c03ae215>] pskb_expand_head+0xf5/0x170
 [<c04bfd94>] __ieee80211_tx_prepare+0x164/0x2f0
 [<c04c1a8d>] ieee80211_skb_resize+0x6d/0xe0
 [<c04c250f>] ieee80211_master_start_xmit+0x23f/0x550
 [<c016d188>] __slab_alloc+0x2b8/0x4f0
 [<c013a711>] getnstimeofday+0x51/0x120
 [<c03b5e7b>] dev_hard_start_xmit+0x1db/0x240
 [<c03c6a4b>] __qdisc_run+0x1ab/0x200
 [<c0136aa1>] __run_hrtimer+0x31/0xf0
 [<c03b6247>] dev_queue_xmit+0x247/0x500
 [<c04c1e56>] ieee80211_subif_start_xmit+0x356/0x7d0
 [<c0466ff7>] packet_rcv_spkt+0x37/0x150
 [<c0466ff7>] packet_rcv_spkt+0x37/0x150
 [<c03b5e7b>] dev_hard_start_xmit+0x1db/0x240
 [<c03c6a4b>] __qdisc_run+0x1ab/0x200
 [<c03b6247>] dev_queue_xmit+0x247/0x500
 [<c03bc1e2>] neigh_resolve_output+0xe2/0x200
 [<c0410080>] ip_finish_output+0x0/0x290
 [<c0410267>] ip_finish_output+0x1e7/0x290
 [<c040f355>] ip_local_out+0x15/0x20
 [<c040f5d2>] ip_push_pending_frames+0x272/0x380
 [<c042bbc6>] udp_push_pending_frames+0x146/0x3a0
 [<c042d52a>] udp_sendmsg+0x2fa/0x6b0
 [<c0433bc7>] inet_sendmsg+0x37/0x70
 [<c03a7b7e>] sock_sendmsg+0xbe/0x100
 [<c0133cd0>] autoremove_wake_function+0x0/0x50
 [<c011c043>] __wake_up_common+0x43/0x70
 [<c024a892>] copy_from_user+0x32/0x130
 [<c024a892>] copy_from_user+0x32/0x130
 [<c03b001e>] verify_iovec+0x2e/0xb0
 [<c03a7d3f>] sys_sendmsg+0x17f/0x290
 [<c017730a>] pipe_write+0x29a/0x570
 [<c013a172>] update_wall_time+0x492/0x8e0
 [<c013a711>] getnstimeofday+0x51/0x120
 [<c011b05d>] sched_slice+0x3d/0x80
 [<c013a711>] getnstimeofday+0x51/0x120
 [<c0136657>] hrtimer_forward+0x147/0x1a0
 [<c01101b0>] lapic_next_event+0x10/0x20
 [<c013ccb3>] clockevents_program_event+0xa3/0x170
 [<c03a9054>] sys_socketcall+0xa4/0x290
 [<c0110920>] smp_apic_timer_interrupt+0x40/0x70
 [<c0103165>] sysenter_do_call+0x12/0x25

Signed-off-by: Artur Skawina <art.08.09@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: fix a wrong parameter for __test_and_clear_bit() in rt2x00rfkill_free().

When running modprobe rt73usb, and then rmmod rt73usb, and then
iwconfig, the wlan0 device does not disappear. When repeating this
process again, we get a kernel Oops errors and "BUG: unable to handle
kernel paging request..." message in the kernel log.

The reason for this is that there is an error in rt2x00rfkill_free(),
which is called in the process of removing the device
(rt2x00lib_remove_dev() in rt2x00dev.c).
rt2x00rfkill_free() clears the RFKILL_STATE_ALLOCATED bit , which is
bit number 1 () in rt2x00dev->flags instead of in
rt2x00dev->rfkill_state. As a result, when checking the
DEVICE_STATE_REGISTERED_HW bit (bit number 1 in rt2x00dev->flags) in
rt2x00lib_remove_hw() it is **unset**, and we wrongly **don't** call
ieee80211_unregister_hw().

This patch corrects this: the parameter for __test_and_clear_bit() in
rt2x00rfkill_free() should be &rt2x00dev->rfkill_state and not
&rt2x00dev->flags.

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Fix parsed country IE info for 5 GHz

The country IE number of channels on 5 GHz specifies the number
of 5 GHz channels, not the number of sequential channel numbers.
For example, if in a country IEs if the first channel given is 36
and the number of channels passed is 4 then the individual channel
numbers defined for the 5 GHz PHY by these parameters

are: 36, 40, 44, 48
not: 36, 37, 38, 39

See: http://tinyurl.com/11d-clarification

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Fix regression with 11d on bands

This fixes a regression on disallowing bands introduced with the new
802.11d support. The issue is that IEEE-802.11 allows APs to send
a subset of what a country regulatory domain defines. This was clarified
in this document:

http://tinyurl.com/11d-clarification

As such it is possible, and this is what is done in practice, that a
single band 2.4 GHz AP will only send 2.4 GHz band regulatory information
through the 802.11 country information element and then the current
intersection with what CRDA provided yields a regulatory domain with
no 5 GHz information -- even though that country may actually allow
5 GHz operation. We correct this by only applying the intersection rules
on a channel if the the intersection yields a regulatory rule on the
same band the channel is on.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: make handle_band() and handle_channel() wiphy specific

This allows us to make more wiphy specific judgements when
handling the channels later on.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: remove CMD_WANT_SKB flag if send_cmd_sync failure

In function iwl_send_cmd_sync(), if the flag CMD_WANT_SKB is set but
we are not provided with a valid SKB (cmd->meta.u.skb == NULL), we need
to remove the CMD_WANT_SKB flag from the TX cmd queue. Otherwise in case
the cmd comes in later, it will possibly set an invalid address. Thus
it causes an invalid memory access.

This fixed the bug http://bugzilla.kernel.org/show_bug.cgi?id=11326.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix an operator typo in REG_DOMAIN_2GHZ_MASK

Incorrect operator causes the REG_DOMAIN_2GHZ_MASK to be zero which
surely was not the goal of this definition. Mask out the 11a flags
correctly.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix an operator typo in phy rate validation

This was not supposed to be a bitwise AND operation, but a check of
two separate conditions. Anyway, the old code happened to result in
the same behavior, so this is just changing the code to be easier to
understand and also to keep sparse from warning about dubious
operators.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: Fix alignment issues in libertas core

Data structures that come over the wire from the WLAN firmware must be packed.
This fixes alignment problems on the blackfin architecture and, reportedly, on
the AVR32.

This is a replacement for the previous version of this patch which had also
explicitly used get_unaligned_ macros.  As Johannes Berg pointed out, these
macros were unnecessary.

Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: more kernel-doc fixes

Fix (delete) more mac80211 kernel-doc:

Warning(linux-2.6.28-git13//include/net/mac80211.h:375): Excess struct/union/enum/typedef member 'retry_count' description in 'ieee80211_tx_info'
Warning(linux-2.6.28-git13//net/mac80211/sta_info.h:308): Excess struct/union/enum/typedef member 'last_txrate' description in 'sta_info'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: fix oops caused by bad eeproms

This patch fixes a bug that could occur, if it the eeprom is incomplete or partly corrupted.

BUG: unable to handle kernel NULL pointer dereference at 00000008
IP: p54_assign_address+0x108/0x15d [p54common]
Oops: 0002 [#1] SMP
Pid: 12988, comm: phy1 Tainted: P        W  2.6.28-rc6-wl #3
RIP: 0010: p54_assign_address+0x108/0x15d [p54common]
 [...]
Call Trace:
 p54_alloc_skb+0xa3/0xc0 [p54common]
 p54_scan+0x37/0x204 [p54common]
 [...]

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IPoIB: Do not print error messages for multicast join retries

When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status.  In that case, don't print an error
message unless multicast debugging is enabled.

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

IB/mlx4: Fix memory ordering problem when posting LSO sends

The current work request posting code writes the LSO segment before
writing any data segments.  This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments.  When the HCA processes this work request, a local
protection error may result.

Fix this by saving the LSO header size field off and writing it only
after all data segments are written.  This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.

Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Linux 2.6.29-rc2

Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
  ACPI PCI hotplug: harden against panic regression
  ACPI: rename main.c to sleep.c
  dell-laptop: move to drivers/platform/x86/ from drivers/misc/
  eeepc-laptop: enable Bluetooth ACPI details
  ACPI: fix ACPI_FADT_S4_RTC_WAKE comment
  kprobes: check CONFIG_FREEZER instead of CONFIG_PM
  PM: Fix freezer compilation if PM_SLEEP is unset
  thermal fixup for broken BIOS which has invalid trip points.
  ACPI: EC: Don't trust ECDT tables from ASUS
  ACPI: EC: Limit workaround for ASUS notebooks even more
  ACPI: thinkpad-acpi: bump up version to 0.22
  ACPI: thinkpad-acpi: handle HKEY event 6030
  ACPI: thinkpad-acpi: clean-up fan subdriver quirk
  ACPI: thinkpad-acpi: start the event hunt season
  ACPI: thinkpad-acpi: handle HKEY thermal and battery alarms
  ACPI: thinkpad-acpi: clean up hotkey_notify()
  ACPI: thinkpad-acpi: use killable instead of interruptible mutexes
  ACPI: thinkpad-acpi: add UWB radio support
  ACPI: thinkpad-acpi: preserve radio state across shutdown
  ACPI: thinkpad-acpi: resume with radios disabled
  ...

Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  netxen: include ipv6.h (fixes build failure)
  netxen: avoid invalid iounmap

ACPI PCI hotplug: harden against panic regression

ACPI hotplug panic with current git head
http://lkml.org/lkml/2009/1/10/136

Rather than reverting the entire commit that causes the crash:
e8c331e963c58b83db24b7d0e39e8c07f687dbc6
"PCI hotplug: introduce functions for ACPI slot detection"

simply harden against it while the changes to
the hotplug code on this particularl machine are understood.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>

Merge branch 'misc' into release

Merge branch 'thinkpad-acpi' into release

Merge branches 'bugzilla-11884' and 'bugzilla-8544' into release

ACPI: rename main.c to sleep.c

Signed-off-by: Len Brown <len.brown@intel.com>

dell-laptop: move to drivers/platform/x86/ from drivers/misc/

Signed-off-by: Len Brown <len.brown@intel.com>

eeepc-laptop: enable Bluetooth ACPI details

Although rfkill support for the EEE bluetooth device has been added to
2.6.28-rc the appropriate ACPI accessor definitions were not added, so
the support was non functional. The patch below adds the get and set
accessors and has been verified to work on an EEE 901.

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>

ACPI: fix ACPI_FADT_S4_RTC_WAKE comment

Make the comment for ACPI_FADT_S4_RTC_WAKE match the ACPI spec;
that bit has nothing to do with status bits.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>

kprobes: check CONFIG_FREEZER instead of CONFIG_PM

Check CONFIG_FREEZER instead of CONFIG_PM because kprobe booster
depends on freeze_processes() and thaw_processes() when CONFIG_PREEMPT=y.

This fixes a linkage error which occurs when CONFIG_PREEMPT=y, CONFIG_PM=y
and CONFIG_FREEZER=n.

Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Len Brown <len.brown@intel.com>

PM: Fix freezer compilation if PM_SLEEP is unset

Freezer fails to compile if with the following configuration
settings:

CONFIG_CGROUPS=y
CONFIG_CGROUP_FREEZER=y
CONFIG_MODULES=y
CONFIG_FREEZER=y
CONFIG_PM=y
CONFIG_PM_SLEEP=n

Fix this by making process.o compilation depend on CONFIG_FREEZER.

Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>

thermal fixup for broken BIOS which has invalid trip points.

ACPI thermal driver only re-evaluate VALID trip points.

For the broken BIOS show in
http://bugzilla.kernel.org/show_bug.cgi?id=8544
the active[0] is set to invalid at boot time
and it will not be re-evaluated again.
We can still get a single warning message at boot time.

http://marc.info/?l=linux-kernel&m=120496222629983&w=2

http://bugzilla.kernel.org/show_bug.cgi?id=12203

Signed-off-by: Zhang Rui<rui.zhang@intel.com>
Tested-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Len Brown <len.brown@intel.com>

netxen: include ipv6.h (fixes build failure)

Fixes a build error in absence of CONFIG_IPV6:

drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ACPI: EC: Don't trust ECDT tables from ASUS

http://bugzilla.kernel.org/show_bug.cgi?id=9399
http://bugzilla.kernel.org/show_bug.cgi?id=11880

Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>

netxen: avoid invalid iounmap

For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.

"Attempt to iounmap early bolted mapping at 0x0000000000000000"

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>