iio: adc: max1027: Simplify the _set_trigger_state() helper

The call to max1027_enable_trigger() is the same in both cases thanks to
the 'state' variable, so factorize a little bit to simplify the code and
explain why we call this helper.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-8-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max1027: Create a helper to enable/disable the cnvst trigger

There are two ways to physically trigger a conversion:
- A falling edge on the cnvst pin
- A write operation on the conversion register

Let's create a helper for this.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-7-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max1027: Rename a helper

Make it clear that the *_set_trigger_state() hook is responsible for
cnvst based conversions by renaming the helper. This may avoid
confusions with software trigger support that is going to be
introduced.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-6-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max1027: Minimize the number of converted channels

Provide a list of ->available_scan_masks which match the device's
capabilities. Basically, these devices are able to scan from 0 to N, N
being the highest voltage channel requested by the user. The temperature
can be included or not, but cannot be retrieved alone.

The consequence is, instead of reading and pushing to the IIO buffers
all channels each time, the "minimum" number of channels will be scanned
and pushed based on the ->active_scan_mask.

For example, if the user wants channels 1, 4 and 5, all channels from
0 to 5 will be scanned and pushed to the IIO buffers. The core will then
filter out the unneeded samples based on the ->active_scan_mask that has
been selected and only channels 1, 4 and 5 will be available to the user
in the shared buffer.

Provide a comment in the code explaining this logic.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-5-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max1027: Drop useless debug messages

These two debug messages bring absolutely no value, let's drop them.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-4-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max1027: Drop extra warning message

Memory allocation errors automatically trigger the right logs, no need
to have our own.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-3-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: max1027: Fix style

Follow checkpatch.pl's main advices before hacking into the driver, mainly:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int *' to bare use of 'unsigned *'
CHECK: Comparison to NULL could be written "!foo"
CHECK: Alignment should match open parenthesis

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-2-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

MAINTAINERS: Add the driver info of the NXP IMX8QXP

The NXP i.MX 8QuadXPlus SOC has a new ADC IP. After adding
the driver support for it, I add the driver info of the
NXP IMX8QXP ADC to MAINTAINERS file.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925020555.129-4-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: Add binding documentation for NXP IMX8QXP ADC

The NXP i.MX 8QuadXPlus SOC a new ADC IP, so add
binding documentation for NXP IMX8QXP ADC.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925020555.129-3-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC

The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add
driver support for this ADC.

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: fxls8962af: add wake on event

This adds ways for the SoC to wake from accelerometer wake events.

In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.

If buffered reads are enabled they will be deactivated before suspend.
As the onboard buffer is only holding up to 32 12-bit X/Y/Z data
triplets.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210920114221.1595543-2-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: fxls8962af: add threshold event handling

Add event channels that control the creation of motion events.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20210920114221.1595543-1-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Get and set trimming data.

The ADC controller has a trimming register for fine-tune the reference
voltage. The trimming value comes from the OTP register which will be
written during chip production. This patch will read this OTP value and
configure it to the ADC register when the ADC controller probes and using
dts property "aspeed,trim-data-valid" to determine whether to execute this
flow.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Support battery sensing.

In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Add compensation phase.

This patch adds a compensation phase to improve the accuracy of ADC
measurement. This is the built-in function through input half of the
reference voltage to get the ADC offset.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-10-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Add func to set sampling rate.

Add the function to set the sampling rate and keep the sampling period
for a driver used to wait the fresh value.
In addition, since the ADC clock is required when initializing the ADC
device, move clk_prepare_enable ahead of the initialization phase.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-9-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Fix the calculate error of clock.

The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Support ast2600 adc.

Make driver to support ast2600 adc device.
- Use shared reset controller
- Complete the vref configure function
- Add the model data for ast2600 adc

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-7-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Use devm_add_action_or_reset.

This patch use devm_add_action_or_reset to handle the error in probe
phase.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-6-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Use model_data to set clk scaler.

This patch uses need_prescaler and scaler_bit_width to set the ADC clock
scaler.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-5-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Add vref config function

Add the function to check the vref_fixed_mv and set the value to driver
data.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-4-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Restructure the model data

This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: Keep model data to driver data.

Keep the model data pointer to driver data for reducing the usage of
of_device_get_match_data().

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-2-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ABI: Document in_concentration_co2_scale

Document the 'in_concentration_co2_scale' standard IIO attribute.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Link: https://lore.kernel.org/r/20210920135413.140310-5-jacopo+renesas@jmondi.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: chemical: Add Senseair Sunrise 006-0-007 driver

Add support for the Senseair Sunrise 006-0-0007 driver through the
IIO subsystem.

Datasheet: https://rmtplusstoragesenseair.blob.core.windows.net/docs/Dev/publicerat/TDE5531.pdf
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Link: https://lore.kernel.org/r/20210920135413.140310-4-jacopo+renesas@jmondi.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ABI: docs: Document Senseair Sunrise ABI

Add documentation for the sysfs attributes of the sunrise_co2 driver.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Link: https://lore.kernel.org/r/20210920135413.140310-3-jacopo+renesas@jmondi.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: chemical: Document senseair,sunrise CO2 sensor

Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920135413.140310-2-jacopo+renesas@jmondi.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: magnetometer: asahi-kasei,ak8975 add vid reg

Driver and device-tree also use vid-supply regulator.

Fixes: 7e000fbff7a0 ("dt-bindings: iio: magnetometer: ak8975: convert format to yaml, add maintainer")
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210913181949.83179-1-david@ixit.cz
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: kionix,kxcjk1013: driver support interrupts

Device has interrupts support, which description was missing in the bindings.

Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210919203656.119742-1-david@ixit.cz
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: exynos: describe drivers in KConfig

Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210924133515.112357-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: rockchip_saradc: Make use of the helper function devm_platform_ioremap_resource()

Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105631.1474-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: stm32-dac: Make use of the helper function devm_platform_ioremap_resource()

Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105638.1525-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: mma7660: Mark acpi match table as maybe unused

When building kernels without ACPI support the table is declared
but is not used because ACPI_PTR() turns it into a NULL.

Add the __maybe_unused attribute to stop the compiler whining.

Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20210919072616.3849723-1-daniel@0x0f.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: light: max44000: use device-managed functions in probe

This is a simple conversion. Both iio_device_register() and
iio_triggered_buffer_setup() functions have device-managed variants.

Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913120002.306280-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: gyro: adis16080: use devm_iio_device_register() in probe

There is nothing else that needs to be done for this driver. The remove
hook calls only the iio_device_unregister() hook.

So this driver can use devm_iio_device_register() directly.

Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115308.301877-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad5064: convert probe to full device-managed

This change converts the probe of the AD5064 driver to use only
device-managed functions.

The regulator_bulk_disable() is passed on a devm_add_action_or_reset() hook
and the devm_iio_device_register() can be used to register the IIO device.

The driver has both I2C and SPI hooks inside, so all these can be removed.

Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115237.301310-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: ad9832: convert probe to device-managed

This change does a conversion of the driver to use device-managed init
functions. The 2 regulators and the clock inits are converted to use
devm_add_action_or_reset() callbacks for de-initializing them when the
driver unloads.

And finally the devm_iio_device_register() function can be use to register
the device.

The remove hook can finally be removed and the spi_set_drvdata() call can
also be removed as the private data is no longer used.

Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115209.300665-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: dac: ad7303: convert probe to full device-managed

For this conversion, the regulators need to have some cleanup hooks
registered with devm_add_action_or_reset() and then the
devm_io_device_register() call can be used.

Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210913115121.300082-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: imu: inv_mpu6050: Mark acpi match table as maybe unused

When building kernels without ACPI support the table is declared
but is not used because ACPI_PTR() turns it into a NULL.

Add the __maybe_unused attribute to stop the compiler whining.

Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210913112913.2148026-1-daniel@0x0f.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ep93xx: Make use of the helper function devm_platform_ioremap_resource()

Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105646.1576-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: adxl355: Add triggered buffer support

Provide a way for continuous data capture by setting up buffer support. The
data ready signal exposed at the DRDY pin of the ADXL355 is exploited as
a hardware interrupt which triggers to fill the buffer.

Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Link: https://lore.kernel.org/r/20210903184312.21009-3-puranjay12@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: adxl355: use if(ret) in place of ret < 0

Replace if(ret < 0) with if(ret) for consistency.

Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Link: https://lore.kernel.org/r/20210903184312.21009-2-puranjay12@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: Add driver support for ADXL313

ADXL313 is a small, thin, low power, 3-axis accelerometer with high
resolution measurement up to +/-4g. It includes an integrated 32-level
FIFO and has activity and inactivity sensing capabilities.

Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL313.pdf
Signed-off-by: Lucas Stankus <lucas.p.stankus@gmail.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/d16e2d1967e46bb2b1024b6d23bc4889da77dc6b.1630523106.git.lucas.p.stankus@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: accel: Add binding documentation for ADXL313

Add device tree binding documentation for ADXL313 3-axis accelerometer.

Signed-off-by: Lucas Stankus <lucas.p.stankus@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/2eff22d1d22f7e72efdabdc681d02e922682c434.1630523106.git.lucas.p.stankus@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: aspeed: completes the bitfield declare.

This patch completes the declare of ADC register bitfields and uses the
same prefix ASPEED_ADC_* for these bitfields. In addition, tidy up space
alignment of the codes.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210831071458.2334-4-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: Add ast2600-adc bindings

Add device tree bindings document for the aspeed ast2600 adc device
driver.

Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210831071458.2334-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ti-ads8344: convert probe to device-managed

This change converts the driver to register via devm_iio_device_register().
The regulator disable is moved on a devm_add_action_or_reset() hook.

And the spi_set_drvdata() isn't required anymore.
And finally, the ads8344_remove() can be removed as well.

Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210903073707.46892-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2_adc: update copyright and authors information

Update copyright and authors information (corrected e-mail address), and
add myself as one of the authors.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-9-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2_adc: add support for sama7g5 device

Add support to sama7g5 ADC which is similar with sama5d2/sam9x60 device.
Differences are highlighted by compatible.
Main differences include 16 channels instead of 12 and missing
resistive touchscreen.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-8-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2_adc: add helper for COR register

Add helper for the COR register. This helper allows to modify the COR
register, removes duplicate code and improves readability.
The COR offset is now part of the register layout. This will allow
different platform with a different offset to use the same helper.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-7-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2_adc: add support for separate end of conversion registers

Some platforms have separated the end-of-conversion information from the
usual ISR/IMR/IER/IDR registers, into EOC_ISR/EOC_IMR/EOC_IER/EOC_IDR.
To cope with both variants, helpers are being added, that will make
code more clear and more easy to read.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-6-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2_adc: convert to platform specific data structures

Convert the driver to platform specific structures. This means:
- create a register layout struct that will hold offsets for registers
- create a platform struct that will hold platform information (number of
channels, indexes for different channels and pointer to layout struct)
- convert specific macros that are platform dependent into platform variables

This step is in fact a no-op, but allows the driver to be more flexible
and for future enhancement including adding new platforms that are partly
compatible with the current driver and differ slightly in register layout
or capabilities for example.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-5-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2_adc: remove unused definition

Remove unused register definition

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-4-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: at91-sama5d2_adc: initialize hardware after clock is started

The hw_init hardware init call must happen after the clock is prepared and
enabled. Otherwise, writing to the registers might lead to a block or
external abort.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-3-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: at91-sama5d2: add compatible for sama7g5-adc

Add compatible for microchip,sama7g5-adc device.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-2-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: magnetometer: ak8975: add AK09116 support

Add additional AK09116 to the magnetometer driver which has the same
register mapping and scaling as the AK09112 device.

Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Link: https://lore.kernel.org/r/20210825020738.35877-1-matt.ranostay@konsulko.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: temperature: add MAXIM max31865 support

Add DT bindings for MAXIM max31865 RTD sensor.

Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210824050650.72619-1-navin@linumiz.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: temperature: Add MAX31865 RTD Support

This patch adds support for Maxim MAX31865 RTD temperature
sensor support.

More information can be found in:
https://datasheets.maximintegrated.com/en/ds/MAX31865.pdf

Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>
Link: https://lore.kernel.org/r/20210824050123.71289-1-navin@linumiz.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: twl6030-gpadc: Use the defined variable to clean code

Use the defined variable "dev" to make the code cleaner.

Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210823095921.16828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

staging: iio: cdc: remove braces from single line if blocks

Remove braces from single line if blocks to clear checkpatch warnings.
WARNING: braces {} are not necessary for single statement blocks

Signed-off-by: Alexander Vorwerk <alec@vc-celle.de>
Link: https://lore.kernel.org/r/20210820224914.1260-1-alec@vc-celle.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ltc2983: fail probe if no channels are given

If there are no channels defined in the devicetree, there's no point in
probing the device. We were actually requesting a zero sized 'kmalloc'
array but since we were not touching the ZERO_SIZE_PTR afterwards,
nothing bad was actually happening. Hence this is not really a fix but
rather an improvement.

Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210825084149.11587-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ltc2983: add support for optional reset gpio

Check if an optional reset gpio is present and if so, make sure to reset
the device.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210825084149.11587-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: ad5770r: make devicetree property reading consistent

The bindings file for this driver is defining the property as 'reg' but
the driver was reading it with the 'num' name. The bindings actually had
the 'num' property when added in
commit ea52c21268e6 ("dt-bindings: iio: dac: Add docs for AD5770R DAC")
and then changed it to 'reg' in
commit 2cf3818f18b2 ("dt-bindings: iio: dac: AD5570R fix bindings errors").
However, both these commits landed in v5.7 so the assumption is
that either 'num' is not being used or if it is, the validations were not
done.

Anyways, if someone comes back yelling about this, we might just support
both of the properties in the future. Not ideal, but that's life...

Fixes: 2cf3818f18b2 ("dt-bindings: iio: dac: AD5570R fix bindings errors")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210818080525.62790-1-nuno.sa@analog.com
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: gyro: remove dead config dependencies on INPUT_MPU3050

Commit b1fe0cf06f92 ("Input: delete MPU3050 driver") deletes the superseded
MPU3050 driver and its corresponding config INPUT_MPU3050.

The dependencies on the superseding driver in ./drivers/iio/gyro/Kconfig
to ensure that the two drivers are not built into the same kernel is a dead
dependency and not required anymore.

So, remove those config dependencies on INPUT_MPU3050 for MPU3050_I2C.

This issue was detected with ./scripts/checkkconfigsymbols.py.

Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210817081330.9645-1-lukas.bulwahn@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: remove reference to parent device object on st_sensor_data

The idea behind it, is that all devm_ calls in ST sensors are bound to the
parent device object.

However, the reference to that object is kept on both the st_sensor_data
struct and the IIO object parent (indio_dev->dev.parent).

This change only adds a bit consistency and uses the reference stored on
indio_dev->dev.parent, to enforce the assumption that all ST sensors' devm_
calls are bound to the same reference as the one store on st_sensor_data.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210823112204.243255-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: remove all driver remove functions

At this point all ST driver remove functions do iio_device_unregister().
This change removes them from them and replaces all iio_device_register()
with devm_iio_device_register().

This can be done in a single change relatively easy, since all these remove
functions are define in st_sensors.h.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210823112204.243255-5-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: remove st_sensors_power_disable() function

This change converts the st_sensors_power_enable() function to use
devm_add_action_or_reset() handlers to register regulator_disable hooks for
when the drivers get unloaded.

The parent device of the IIO device object is used. This is based on the
assumption that all other devm_ calls in the ST sensors use this reference.

This makes the st_sensors_power_disable() un-needed.
Removing this also changes unload order a bit, as all ST drivers would call
st_sensors_power_disable() first and iio_device_unregister() after that.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210823112204.243255-4-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: remove st_sensors_deallocate_trigger() function

This change converts the st_sensors_allocate_trigger() to use
device-managed functions.

The parent device of the IIO device object is used. This is based on the
assumption that all other devm_ calls in the ST sensors use this reference.

That makes the st_sensors_deallocate_trigger() function un-needed, so it
can be removed.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210823112204.243255-3-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: st_sensors: disable regulators after device unregistration

Up until commit ea7e586bdd331 ("iio: st_sensors: move regulator retrieveal
to core") only the ST pressure driver seems to have had any regulator
disable. After that commit, the regulator handling was moved into the
common st_sensors logic.

In all instances of this regulator handling, the regulators were disabled
before unregistering the IIO device.
This can cause issues where the device would be powered down and still be
available to userspace, allowing it to send invalid/garbage data.

This change moves the st_sensors_power_disable() after the common probe
functions. These common probe functions also handle unregistering the IIO
device.

Fixes: 774487611c949 ("iio: pressure-core: st: Provide support for the Vdd power supply")
Fixes: ea7e586bdd331 ("iio: st_sensors: move regulator retrieveal to core")
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210823112204.243255-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7949: use devm managed functions

Switch to devm_iio_device_register to finalize devm migration.
This removes the use for iio_device_unregister() and since
mutex_destroy() is not necessary here, remove it altogether.

Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-6-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: adc: ad7949: update voltage reference bindings

Update bindings to describe support for buffered and unbuffered external
voltage references selection, and add adi,internal-ref-microvolt for
internal voltage reference selection.

Signed-off-by: Liam Beguin <lvb@xiphos.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210815213309.2847711-5-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7949: add vref selection support

Add support for selecting the voltage reference from the devicetree.

This change is required to get valid readings with all three
vref hardware configurations supported by the ADC.

For instance if the ADC isn't provided with an external reference,
the sample request must specify an internal voltage reference to get a
valid reading.

Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-4-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7949: enable use with non 14/16-bit controllers

This driver supports devices with 14-bit and 16-bit sample sizes.
This implies different SPI transfer lengths which are not always handled
properly by some SPI controllers.

To work around this limitation, define a big endian buffer used to split
the buffer into two 8-bit messages in the event that the controller
doesn't support 14-bit or 16-bit transfers.
A separate buffer is introduced here to avoid performing operations on
types of different endianness.

Since all transfers use the same bits_per_word value, move that logic to
the probe function, and let transfers default to the value defined in
the struct spi_device.

Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-3-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: adc: ad7949: define and use bitfield names

Replace raw configuration register values by using FIELD_PREP and
defines to improve readability.

Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-2-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

drivers/iio: Remove all strcpy() uses

strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. So, remove all the uses and add
devm_kstrdup() or devm_kasprintf() instead.

Also, modify the "for" loop conditions to clarify the access to the
st->orientation.rotation buffer.

This patch is an effort to clean up the proliferation of str*()
functions in the kernel and a previous step in the path to remove
the strcpy function from the kernel entirely [1].

[1] https://github.com/KSPP/linux/issues/88

Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210815174204.126593-1-len.baker@gmx.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

iio: accel: Add driver support for ADXL355

ADXL355 is a 3-axis MEMS Accelerometer. It offers low noise density,
low 0g offset drift, low power with selectable measurement ranges.
It also features programmable high-pass and low-pass filters.

Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/adxl354_adxl355.pdf
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Link: https://lore.kernel.org/r/20210811073027.124619-3-puranjay12@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

dt-bindings: iio: accel: Add DT binding doc for ADXL355

Add devicetree binding document for ADXL355, a 3-Axis MEMS Accelerometer.

Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210811073027.124619-2-puranjay12@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Linux 5.15-rc1

Merge tag 'perf-tools-for-v5.15-2021-09-11' of git://git./linux/kernel/git/acme/linux

Pull more perf tools updates from Arnaldo Carvalho de Melo:

 - Add missing fields and remove some duplicate fields when printing a
   perf_event_attr.

 - Fix hybrid config terms list corruption.

 - Update kernel header copies, some resulted in new kernel features
   being automagically added to 'perf trace' syscall/tracepoint argument
   id->string translators.

 - Add a file generated during the documentation build to .gitignore.

 - Add an option to build without libbfd, as some distros, like Debian
   consider its ABI unstable.

 - Add support to print a textual representation of IBS raw sample data
   in 'perf report'.

 - Fix bpf 'perf test' sample mismatch reporting

 - Fix passing arguments to stackcollapse report in a 'perf script'
   python script.

 - Allow build-id with trailing zeros.

 - Look for ImageBase in PE file to compute .text offset.

* tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (25 commits)
  tools headers UAPI: Update tools's copy of drm.h headers
  tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
  tools headers UAPI: Sync linux/fs.h with the kernel sources
  tools headers UAPI: Sync linux/in.h copy with the kernel sources
  perf tools: Add an option to build without libbfd
  perf tools: Allow build-id with trailing zeros
  perf tools: Fix hybrid config terms list corruption
  perf tools: Factor out copy_config_terms() and free_config_terms()
  perf tools: Fix perf_event_attr__fprintf() missing/dupl. fields
  perf tools: Ignore Documentation dependency file
  perf bpf: Provide a weak btf__load_from_kernel_by_id() for older libbpf versions
  tools include UAPI: Update linux/mount.h copy
  perf beauty: Cover more flags in the  move_mount syscall argument beautifier
  tools headers UAPI: Sync linux/prctl.h with the kernel sources
  tools include UAPI: Sync sound/asound.h copy with the kernel sources
  tools headers UAPI: Sync linux/kvm.h with the kernel sources
  tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
  perf report: Add support to print a textual representation of IBS raw sample data
  perf report: Add tools/arch/x86/include/asm/amd-ibs.h
  perf env: Add perf_env__cpuid, perf_env__{nr_}pmu_mappings
  ...

Merge tag 'compiler-attributes-for-linus-v5.15-rc1-v2' of git://github.com/ojeda/linux

Pull compiler attributes updates from Miguel Ojeda:

 - Fix __has_attribute(__no_sanitize_coverage__) for GCC 4 (Marco Elver)

 - Add Nick as Reviewer for compiler_attributes.h (Nick Desaulniers)

 - Move __compiletime_{error|warning} (Nick Desaulniers)

* tag 'compiler-attributes-for-linus-v5.15-rc1-v2' of git://github.com/ojeda/linux:
  compiler_attributes.h: move __compiletime_{error|warning}
  MAINTAINERS: add Nick as Reviewer for compiler_attributes.h
  Compiler Attributes: fix __has_attribute(__no_sanitize_coverage__) for GCC 4

Merge tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux

Pull auxdisplay updates from Miguel Ojeda:
 "An assortment of improvements for auxdisplay:

   - Replace symbolic permissions with octal permissions (Jinchao Wang)

   - ks0108: Switch to use module_parport_driver() (Andy Shevchenko)

   - charlcd: Drop unneeded initializers and switch to C99 style (Andy
     Shevchenko)

   - hd44780: Fix oops on module unloading (Lars Poeschel)

   - Add I2C gpio expander example (Ralf Schlatterbeck)"

* tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux:
  auxdisplay: Replace symbolic permissions with octal permissions
  auxdisplay: ks0108: Switch to use module_parport_driver()
  auxdisplay: charlcd: Drop unneeded initializers and switch to C99 style
  auxdisplay: hd44780: Fix oops on module unloading
  auxdisplay: Add I2C gpio expander example

Merge tag 'smp-urgent-2021-09-12' of git://git./linux/kernel/git/tip/tip

Pull CPU hotplug updates from Thomas Gleixner:
 "Updates for the SMP and CPU hotplug:

   - Remove DEFINE_SMP_CALL_CACHE_FUNCTION() which is a left over of the
     original hotplug code and now causing trouble with the ARM64 cache
     topology setup due to the pointless SMP function call.

     It's not longer required as the hotplug callbacks are guaranteed to
     be invoked on the upcoming CPU.

   - Remove the deprecated and now unused CPU hotplug functions

   - Rewrite the CPU hotplug API documentation"

* tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Documentation: core-api/cpuhotplug: Rewrite the API section
  cpu/hotplug: Remove deprecated CPU-hotplug functions.
  thermal: Replace deprecated CPU-hotplug functions.
  drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION()

Merge tag 'char-misc-5.15-rc1-lkdtm' of git://git./linux/kernel/git/gregkh/char-misc

Pull misc driver fix from Greg KH:
 "Here is a single patch for 5.15-rc1, for the lkdtm misc driver.

  It resolves a build issue that many people were hitting with your
  current tree, and Kees and others felt would be good to get merged
  before -rc1 comes out, to prevent them from having to constantly hit
  it as many development trees restart on -rc1, not older -rc releases.

  It has NOT been in linux-next, but has passed 0-day testing and looks
  'obviously correct' when reviewing it locally :)"

* tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  lkdtm: Use init_uts_ns.name instead of macros

Merge tag 'for-linus-5.15-1' of git://github.com/cminyard/linux-ipmi

Pull IPMI updates from Corey Minyard:
 "A couple of very minor fixes for style and rate limiting.

  Nothing big, but probably needs to go in"

* tag 'for-linus-5.15-1' of git://github.com/cminyard/linux-ipmi:
  char: ipmi: use DEVICE_ATTR helper macro
  ipmi: rate limit ipmi smi_event failure message

Merge tag 'sched_urgent_for_v5.15_rc1' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Borislav Petkov:

 - Make sure the idle timer expires in hardirq context, on PREEMPT_RT

 - Make sure the run-queue balance callback is invoked only on the
   outgoing CPU

* tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Prevent balance_push() on remote runqueues
  sched/idle: Make the idle timer expire in hard interrupt context

Merge tag 'locking_urgent_for_v5.15_rc1' of git://git./linux/kernel/git/tip/tip

Pull locking fixes from Borislav Petkov:

 - Fix the futex PI requeue machinery to not return to userspace in
   inconsistent state

 - Avoid a potential null pointer dereference in the ww_mutex deadlock
   check

 - Other smaller cleanups and optimizations

* tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/rtmutex: Fix ww_mutex deadlock check
  futex: Remove unused variable 'vpid' in futex_proxy_trylock_atomic()
  futex: Avoid redundant task lookup
  futex: Clarify comment for requeue_pi_wake_futex()
  futex: Prevent inconsistent state and exit race
  futex: Return error code instead of assigning it without effect
  locking/rwsem: Add missing __init_rwsem() for PREEMPT_RT

Merge tag 'timers_urgent_for_v5.15_rc1' of git://git./linux/kernel/git/tip/tip

Pull timer fix from Borislav Petkov:

 - Handle negative second values properly when converting a timespec64
   to nanoseconds.

* tag 'timers_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Handle negative seconds correctly in timespec64_to_ns()

Merge branch 'misc.namei' of git://git./linux/kernel/git/viro/vfs

Pull namei updates from Al Viro:
 "Clearing fallout from mkdirat in io_uring series. The fix in the
  kern_path_locked() patch plus associated cleanups"

* 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  putname(): IS_ERR_OR_NULL() is wrong here
  namei: Standardize callers of filename_create()
  namei: Standardize callers of filename_lookup()
  rename __filename_parentat() to filename_parentat()
  namei: Fix use after free in kern_path_locked

Merge tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6

Pull smbfs updates from Steve French:
 "cifs/smb3 updates:

   - DFS reconnect fix

   - begin creating common headers for server and client

   - rename the cifs_common directory to smbfs_common to be more
     consistent ie change use of the name cifs to smb (smb3 or smbfs is
     more accurate, as the very old cifs dialect has long been
     superseded by smb3 dialects).

  In the future we can rename the fs/cifs directory to fs/smbfs.

  This does not include the set of multichannel fixes nor the two
  deferred close fixes (they are still being reviewed and tested)"

* tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: properly invalidate cached root handle when closing it
  cifs: move SMB FSCTL definitions to common code
  cifs: rename cifs_common to smbfs_common
  cifs: update FSCTL definitions

Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost

Pull virtio updates from Michael Tsirkin:

 - vduse driver ("vDPA Device in Userspace") supporting emulated virtio
   block devices

 - virtio-vsock support for end of record with SEQPACKET

 - vdpa: mac and mq support for ifcvf and mlx5

 - vdpa: management netlink for ifcvf

 - virtio-i2c, gpio dt bindings

 - misc fixes and cleanups

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
  Documentation: Add documentation for VDUSE
  vduse: Introduce VDUSE - vDPA Device in Userspace
  vduse: Implement an MMU-based software IOTLB
  vdpa: Support transferring virtual addressing during DMA mapping
  vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
  vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
  vhost-iotlb: Add an opaque pointer for vhost IOTLB
  vhost-vdpa: Handle the failure of vdpa_reset()
  vdpa: Add reset callback in vdpa_config_ops
  vdpa: Fix some coding style issues
  file: Export receive_fd() to modules
  eventfd: Export eventfd_wake_count to modules
  iova: Export alloc_iova_fast() and free_iova_fast()
  virtio-blk: remove unneeded "likely" statements
  virtio-balloon: Use virtio_find_vqs() helper
  vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
  vsock_test: update message bounds test for MSG_EOR
  af_vsock: rename variables in receive loop
  virtio/vsock: support MSG_EOR bit processing
  vhost/vsock: support MSG_EOR bit processing
  ...

Merge tag 'riscv-for-linus-5.15-mw1' of git://git./linux/kernel/git/riscv/linux

Pull more RISC-V updates from Palmer Dabbelt:

 - A pair of defconfig additions, for NVMe and the EFI filesystem
   localization options.

 - A larger address space for stack randomization.

 - A cleanup to our install rules.

 - A DTS update for the Microchip Icicle board, to fix the serial
   console.

 - Support for build-time table sorting, which allows us to have
   __ex_table read-only.

* tag 'riscv-for-linus-5.15-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Move EXCEPTION_TABLE to RO_DATA segment
  riscv: Enable BUILDTIME_TABLE_SORT
  riscv: dts: microchip: mpfs-icicle: Fix serial console
  riscv: move the (z)install rules to arch/riscv/Makefile
  riscv: Improve stack randomisation on RV64
  riscv: defconfig: enable NLS_CODEPAGE_437, NLS_ISO8859_1
  riscv: defconfig: enable BLK_DEV_NVME

Merge branch 'for-5.15' of git://git./linux/kernel/git/jlawall/linux

Pull coccinelle updates from Julia Lawall:
 "These changes update some existing semantic patches with
  respect to some recent changes in the kernel.

  Specifically, the change to kvmalloc.cocci searches for
  kfree_sensitive rather than kzfree, and the change to
  use_after_iter.cocci adds list_entry_is_head as a valid
  use of a list iterator index variable after the end of
  the loop"

* 'for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  scripts: coccinelle: allow list_entry_is_head() to use pos
  coccinelle: api: rename kzfree to kfree_sensitive

tools headers UAPI: Update tools's copy of drm.h headers

Picking the changes from:

  17ce9c61c71cbc0d ("drm: document DRM_IOCTL_MODE_RMFB")

Doesn't result in any tooling changes:

  $ tools/perf/trace/beauty/drm_ioctl.sh  > before
  $ cp include/uapi/drm/drm.h tools/include/uapi/drm/drm.h
  $ tools/perf/trace/beauty/drm_ioctl.sh  > after
  $ diff -u before after

Silencing these perf build warnings:

  Warning: Kernel ABI header at 'tools/include/uapi/drm/drm.h' differs from latest version at 'include/uapi/drm/drm.h'
  diff -u tools/include/uapi/drm/drm.h include/uapi/drm/drm.h

Cc: Simon Ser <contact@emersion.fr>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

tools headers UAPI: Sync drm/i915_drm.h with the kernel sources

To pick the changes in:

  b65a9489730a2494 ("drm/i915/userptr: Probe existence of backing struct pages upon creation")
  ee242ca704d38699 ("drm/i915/guc: Implement GuC priority management")
  81340cf3bddded4f ("drm/i915/uapi: reject set_domain for discrete")
  7961c5b60f23dff5 ("drm/i915: Add TTM offset argument to mmap.")
  aef7b67a79564f6c ("drm/i915/uapi: convert drm_i915_gem_userptr to kernel doc")
  e7737b67ab46ee0e ("drm/i915/uapi: reject caching ioctls for discrete")
  3aa8c57fe25a9247 ("drm/i915/uapi: convert drm_i915_gem_set_domain to kernel doc")
  289f5a72009b8f67 ("drm/i915/uapi: convert drm_i915_gem_caching to kernel doc")
  4a766ae40ec83301 ("drm/i915: Drop the CONTEXT_CLONE API (v2)")
  6ff6d61dd2a943bd ("drm/i915: Drop I915_CONTEXT_PARAM_NO_ZEROMAP")
  fe4751c3d513ff4f ("drm/i915: Drop I915_CONTEXT_PARAM_RINGSIZE")
  577729533cdc4e37 ("drm/i915: Document the Virtual Engine uAPI")
  c649432e86ca677d ("drm/i915: Fix busy ioctl commentary")

That doesn't result in any changes to tooling as no new ioctl were
added (at least not perceived by tools/perf/trace/beauty/drm_ioctl.sh).

Addressing this perf build warning:

  Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
  diff -u tools/include/uapi/drm/i915_drm.h include/uapi/drm/i915_drm.h

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

tools headers UAPI: Sync linux/fs.h with the kernel sources

To pick the change in:

  7957d93bf32bc211 ("block: add ioctl to read the disk sequence number")

It adds a new ioctl, but we are still not using that to generate tables
for 'perf trace', so no changes in tooling.

This silences this perf build warning:

  Warning: Kernel ABI header at 'tools/include/uapi/linux/fs.h' differs from latest version at 'include/uapi/linux/fs.h'
  diff -u tools/include/uapi/linux/fs.h include/uapi/linux/fs.h

Cc: Jens Axboe <axboe@kernel.dk>
Cc: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

tools headers UAPI: Sync linux/in.h copy with the kernel sources

To pick the changes in:

  db243b796439c0ca ("net/ipv4/ipv6: Replace one-element arraya with flexible-array members")
  2d3e5caf96b9449a ("net/ipv4: Replace one-element array with flexible-array member")

That don't result in any change in tooling, the structs changed remains
with the same layout.

This addresses this build warning:

  Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
  diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h

Cc: David S. Miller <davem@davemloft.net>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tools: Add an option to build without libbfd

Some distributions, like debian, don't link perf with libbfd. Add a
build flag to make this configuration buildable and testable.

This was inspired by:

  https://lore.kernel.org/linux-perf-users/20210910102307.2055484-1-tonyg@leastfixedpoint.com/T/#u

Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: tony garnock-jones <tonyg@leastfixedpoint.com>
Link: http://lore.kernel.org/lkml/20210910225756.729087-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tools: Allow build-id with trailing zeros

Currently perf saves a build-id with size but old versions assumes the
size of 20.  In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.

I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data.  The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.

  symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.

The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.

  $ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf

  Displaying notes found in: .note.gnu.build-id
    Owner                Data size  Description
    GNU                  0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
      Build ID: 53e4c2f42a4c61a2d632d92a72afa08f

Let's fix this by allowing trailing zeros if the size is different.

Fixes: 39be8d0115b321ed ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tools: Fix hybrid config terms list corruption

A config terms list was spliced twice, resulting in a never-ending loop
when the list was traversed. Fix by using list_splice_init() and copying
and freeing the lists as necessary.

This patch also depends on patch "perf tools: Factor out
copy_config_terms() and free_config_terms()"

Example on ADL:

 Before:

  # perf record -e '{intel_pt//,cycles/aux-sample-size=4096/pp}' uname &
  # jobs
  [1]+  Running                    perf record -e "{intel_pt//,cycles/aux-sample-size=4096/pp}" uname
  # perf top -E 10
    PerfTop:    4071 irqs/sec  kernel: 6.9%  exact: 100.0% lost: 0/0 drop: 0/0 [4000Hz cycles],  (all, 24 CPUs)
  ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

    97.60%  perf           [.] __evsel__get_config_term
     0.25%  [kernel]       [k] kallsyms_expand_symbol.constprop.13
     0.24%  perf           [.] kallsyms__parse
     0.15%  [kernel]       [k] _raw_spin_lock
     0.14%  [kernel]       [k] number
     0.13%  [kernel]       [k] advance_transaction
     0.08%  [kernel]       [k] format_decode
     0.08%  perf           [.] map__process_kallsym_symbol
     0.08%  perf           [.] rb_insert_color
     0.08%  [kernel]       [k] vsnprintf
  exiting.
  # kill %1

After:

  # perf record -e '{intel_pt//,cycles/aux-sample-size=4096/pp}' uname &
  Linux
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.060 MB perf.data ]
  # perf script | head
       perf-exec   604 [001]  1827.312293:                            psb:  psb offs: 0                       ffffffffb8415e87 pt_config_start+0x37 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb856a3bd event_sched_in.isra.133+0xfd ([kernel.kallsyms]) => ffffffffb856a9a0 perf_pmu_nop_void+0x0 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb856b10e merge_sched_in+0x26e ([kernel.kallsyms]) => ffffffffb856a2c0 event_sched_in.isra.133+0x0 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb856a45d event_sched_in.isra.133+0x19d ([kernel.kallsyms]) => ffffffffb8568b80 perf_event_set_state.part.61+0x0 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb8568b86 perf_event_set_state.part.61+0x6 ([kernel.kallsyms]) => ffffffffb85662a0 perf_event_update_time+0x0 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb856a35c event_sched_in.isra.133+0x9c ([kernel.kallsyms]) => ffffffffb8567610 perf_log_itrace_start+0x0 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb856a377 event_sched_in.isra.133+0xb7 ([kernel.kallsyms]) => ffffffffb8403b40 x86_pmu_add+0x0 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb8403b86 x86_pmu_add+0x46 ([kernel.kallsyms]) => ffffffffb8403940 collect_events+0x0 ([kernel.kallsyms])
       perf-exec   604  1827.312293:          1                       branches:  ffffffffb8403a7b collect_events+0x13b ([kernel.kallsyms]) => ffffffffb8402cd0 collect_event+0x0 ([kernel.kallsyms])

Fixes: 30def61f64bac5 ("perf parse-events Create two hybrid cache events")
Fixes: 94da591b1c7913 ("perf parse-events Create two hybrid raw events")
Fixes: 9cbfa2f64c04d9 ("perf parse-events Create two hybrid hardware events")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Link: https //lore.kernel.org/r/20210909125508.28693-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tools: Factor out copy_config_terms() and free_config_terms()

Factor out copy_config_terms() and free_config_terms() so that they can
be reused.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Link: https //lore.kernel.org/r/20210909125508.28693-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>