mips: bpf: fix encoding bug for mm_srlv32_op

[ Upstream commit 17f6c83fb5ebf7db4fcc94a5be4c22d5a7bfe428 ]

For micro-mips, srlv inside POOL32A encoding space should use 0x50
sub-opcode, NOT 0x90.

Some early version ISA doc describes the encoding as 0x90 for both srlv and
srav, this looks to me was a typo. I checked Binutils libopcode
implementation which is using 0x50 for srlv and 0x90 for srav.

v1->v2:
  - Keep mm_srlv32_op sorted by value.

Fixes: f31318fdf324 ("MIPS: uasm: Add srlv uasm instruction")
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: Fix OMAP4430 SDP Ethernet startup

[ Upstream commit 84fb6c7feb1494ebb7d1ec8b95cfb7ada0264465 ]

It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.

Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.

Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult.  We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.

Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.

This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.

This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:

TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).

According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/amd: Fix amd_iommu=force_isolation

[ Upstream commit c12b08ebbe16f0d3a96a116d86709b04c1ee8e74 ]

The parameter is still there but it's ignored. We need to check its
value before deciding to go into passthrough mode for AMD IOMMU v2
capable device.

We occasionally use this parameter to force v2 capable device into
translation mode to debug memory corruption that we suspect is
caused by DMA writes.

To address the following comment from Joerg Roedel on the first
version, v2 capability of device is completely ignored.
> This breaks the iommu_v2 use-case, as it needs a direct mapping for the
> devices that support it.

And from Documentation/admin-guide/kernel-parameters.txt:
  This option does not override iommu=pt

Fixes: aafd8ba0ca74 ("iommu/amd: Implement add_device and remove_device")

Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: sunxi-ng: a33: Set CLK_SET_RATE_PARENT for all audio module clocks

[ Upstream commit 6e6da2039c82271dd873b9ad2b902a692a7dd554 ]

All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.

Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

timekeeping: Use proper seqcount initializer

[ Upstream commit ce10a5b3954f2514af726beb78ed8d7350c5e41c ]

tk_core.seq is initialized open coded, but that misses to initialize the
lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq
consequently lack a name and are hard to read.

Use the proper initializer which takes care of the lockdep map
initialization.

[ tglx: Massaged changelog ]

Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Cc: tj@kernel.org
Cc: johannes.berg@intel.com
Link: https://lkml.kernel.org/r/20181128234325.110011-12-bvanassche@acm.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: hub: delay hub autosuspend if USB3 port is still link training

[ Upstream commit e86108940e541febf35813402ff29fa6f4a9ac0b ]

When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.

USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.

Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

smack: fix access permissions for keyring

[ Upstream commit 5b841bfab695e3b8ae793172a9ff7990f99cc3e2 ]

Function smack_key_permission() only issues smack requests for the
following operations:
 - KEY_NEED_READ (issues MAY_READ)
 - KEY_NEED_WRITE (issues MAY_WRITE)
 - KEY_NEED_LINK (issues MAY_WRITE)
 - KEY_NEED_SETATTR (issues MAY_WRITE)
A blank smack request is issued in all other cases, resulting in
smack access being granted if there is any rule defined between
subject and object, or denied with -EACCES otherwise.

Request MAY_READ access for KEY_NEED_SEARCH and KEY_NEED_VIEW.
Fix the logic in the unlikely case when both MAY_READ and
MAY_WRITE are needed. Validate access permission field for valid
contents.

Signed-off-by: Zoran Markovic <zmarkovic@sierrawireless.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: DaVinci-VPBE: fix error handling in vpbe_initialize()

[ Upstream commit aa35dc3c71950e3fec3e230c06c27c0fbd0067f8 ]

If vpbe_set_default_output() or vpbe_set_default_mode() fails,
vpbe_initialize() returns error code without releasing resources.

The patch adds error handling for that case.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/fpu: Add might_fault() to user_insn()

[ Upstream commit 6637401c35b2f327a35d27f44bda05e327f2f017 ]

Every user of user_insn() passes an user memory pointer to this macro.

Add might_fault() to user_insn() so we can spot users which are using
this macro in sections where page faulting is not allowed.

 [ bp: Space it out to make it more visible. ]

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Rik van Riel <riel@surriel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181128222035.2996-6-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: mmp2: fix TWSI2

[ Upstream commit 1147e05ac9fc2ef86a3691e7ca5c2db7602d81dd ]

Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:

   arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP  58

I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.

I'm also copying some properties from TWSI1 that were missing or
incorrect.

Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: ftrace: don't adjust the LR value

[ Upstream commit 6e803e2e6e367db9a0d6ecae1bd24bb5752011bd ]

The core ftrace code requires that when it is handed the PC of an
instrumented function, this PC is the address of the instrumented
instruction. This is necessary so that the core ftrace code can identify
the specific instrumentation site. Since the instrumented function will
be a BL, the address of the instrumented function is LR - 4 at entry to
the ftrace code.

This fixup is applied in the mcount_get_pc and mcount_get_pc0 helpers,
which acquire the PC of the instrumented function.

The mcount_get_lr helper is used to acquire the LR of the instrumented
function, whose value does not require this adjustment, and cannot be
adjusted to anything meaningful. No adjustment of this value is made on
other architectures, including arm. However, arm64 adjusts this value by
4.

This patch brings arm64 in line with other architectures and removes the
adjustment of the LR value.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Torsten Duwe <duwe@suse.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware/efi: Add NULL pointer checks in efivars API functions

[ Upstream commit ab2180a15ce54739fed381efb4cb12e78dfb1561 ]

Since commit:

   ce2e6db554fa ("brcmfmac: Add support for getting nvram contents from EFI variables")

we have a device driver accessing the efivars API. Several functions in
the efivars API assume __efivars is set, i.e., that they will be accessed
only after efivars_register() has been called. However, the following NULL
pointer access was reported calling efivar_entry_size() from the brcmfmac
device driver:

  Unable to handle kernel NULL pointer dereference at virtual address 00000008
  pgd = 60bfa5f1
  [00000008] *pgd=00000000
  Internal error: Oops: 5 [#1] SMP ARM
  ...
  Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
  Workqueue: events request_firmware_work_func
  PC is at efivar_entry_size+0x28/0x90
  LR is at brcmf_fw_complete_request+0x3f8/0x8d4 [brcmfmac]
  pc : [<c0c40718>]    lr : [<bf2a3ef4>]    psr: a00d0113
  sp : ede7fe28  ip : ee983410  fp : c1787f30
  r10: 00000000  r9 : 00000000  r8 : bf2b2258
  r7 : ee983000  r6 : c1604c48  r5 : ede7fe88  r4 : edf337c0
  r3 : 00000000  r2 : 00000000  r1 : ede7fe88  r0 : c17712c8
  Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
  Control: 10c5387d  Table: ad16804a  DAC: 00000051

Disassembly showed that the local static variable __efivars is NULL,
which is not entirely unexpected given that it is a non-EFI platform.

So add a NULL pointer check to efivar_entry_size(), and to related
functions while at it. In efivars_register() a couple of sanity checks
are added as well.

Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Eric Snowberg <eric.snowberg@oracle.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Julien Thierry <julien.thierry@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: YiFei Zhu <zhuyifei1999@gmail.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181129171230.18699-9-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Thermal: do not clear passive state during system sleep

[ Upstream commit 964f4843a455d2ffb199512b08be8d5f077c4cac ]

commit ff140fea847e ("Thermal: handle thermal zone device properly
during system sleep") added PM hook to call thermal zone reset during
sleep. However resetting thermal zone will also clear the passive state
and thus cancel the polling queue which leads the passive cooling device
state not being cleared properly after sleep.

thermal_pm_notify => thermal_zone_device_reset set passive to 0
thermal_zone_trip_update will skip update passive as `old_target ==
instance->target'.
monitor_thermal_zone => thermal_zone_device_set_polling will cancel
tz->poll_queue, so the cooling device state will not be changed
afterwards.

Reported-by: Kame Wang <kamewang@google.com>
Signed-off-by: Wei Wang <wvw@google.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfsd4: fix crash on writing v4_end_grace before nfsd startup

[ Upstream commit 62a063b8e7d1db684db3f207261a466fa3194e72 ]

Anatoly Trosinenko reports that this:

1) Checkout fresh master Linux branch (tested with commit e195ca6cb)
2) Copy x84_64-config-4.14 to .config, then enable NFS server v4 and build
3) From `kvm-xfstests shell`:

results in NULL dereference in locks_end_grace.

Check that nfsd has been started before trying to end the grace period.

Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc: bcm: brcmstb: Don't leak device tree node reference

[ Upstream commit 1861a7f07e02292830a1ca256328d370deefea30 ]

of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_brcmstb()
doesn't do that, so fix it.

[treding: slightly rewrite to avoid inline comparison]

Fixes: d52fad262041 ("soc: add stubs for brcmstb SoC's")
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sunvdc: Do not spin in an infinite loop when vio_ldc_send() returns EAGAIN

[ Upstream commit a11f6ca9aef989b56cd31ff4ee2af4fb31a172ec ]

__vdc_tx_trigger should only loop on EAGAIN a finite
number of times.

See commit adddc32d6fde ("sunvnet: Do not spin in an
infinite loop when vio_ldc_send() returns EAGAIN") for detail.

Signed-off-by: Young Xiao <YangX92@hotmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix wrong return value of f2fs_acl_create

[ Upstream commit f6176473a0c7472380eef72ebeb330cf9485bf0a ]

When call f2fs_acl_create_masq() failed, the caller f2fs_acl_create()
should return -EIO instead of -ENOMEM, this patch makes it consistent
with posix_acl_create() which has been fixed in commit beaf226b863a
("posix_acl: don't ignore return value of posix_acl_create_masq()").

Fixes: 83dfe53c185e ("f2fs: fix reference leaks in f2fs_acl_create")
Signed-off-by: Tiezhu Yang <kernelpatch@126.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: move dir data flush to write checkpoint process

[ Upstream commit b61ac5b720146c619c7cdf17eff2551b934399e5 ]

This patch move dir data flush to write checkpoint process, by
doing this, it may reduce some time for dir fsync.

pre:
-f2fs_do_sync_file enter
-file_write_and_wait_range  <- flush & wait
-write_checkpoint
-do_checkpoint     <- wait all
-f2fs_do_sync_file exit

now:
-f2fs_do_sync_file enter
-write_checkpoint
-block_operations   <- flush dir & no wait
-do_checkpoint     <- wait all
-f2fs_do_sync_file exit

Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: adv*/tc358743/ths8200: fill in min width/height/pixelclock

[ Upstream commit 2912289a518077ddb8214e05336700148e97e235 ]

The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.

However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.

Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID

[ Upstream commit 7f6232e69539971cf9eaed07a6c14ab4a2361133 ]

Various 2-in-1's use KIOX010A and KIOX020A as HIDs for 2 KXCJ91008
accelerometers. The KIOX010A HID is for the one in the base and the
KIOX020A for the accelerometer in the keyboard.

Since userspace does not have a way yet to deal with (or ignore) the
accelerometer in the keyboard, this commit just adds the KIOX010A HID
for now so that display rotation will work.

Related: https://github.com/hadess/iio-sensor-proxy/issues/166
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: xilinx_dma: Remove __aligned attribute on zynqmp_dma_desc_ll

[ Upstream commit aeaebcc17cdf37065d2693865eeb1ff1c7dc5bf3 ]

Clang warns:

drivers/dma/xilinx/zynqmp_dma.c:166:4: warning: attribute 'aligned' is
ignored, place it after "struct" to apply attribute to type declaration
[-Wignored-attributes]
}; __aligned(64)
   ^
./include/linux/compiler_types.h:200:38: note: expanded from macro
'__aligned'
                                               ^
1 warning generated.

As Nick pointed out in the previous version of this patch, the author
likely intended for this struct to be 8-byte (64-bit) aligned, not
64-byte, which is the default. Remove the hanging __aligned attribute.

Fixes: b0cc417c1637 ("dmaengine: Add Xilinx zynqmp dma engine driver support")
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: mtk-vcodec: Release device nodes in mtk_vcodec_init_enc_pm()

[ Upstream commit 8ea0f2ba0fa3f91ea1b8d823a54b042026ada6b3 ]

of_parse_phandle() returns the device node with refcount incremented.
There are two nodes that are used temporary in mtk_vcodec_init_enc_pm(),
but their refcounts are not decremented.

The patch adds one of_node_put() and fixes returning error codes.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc/tegra: Don't leak device tree node reference

[ Upstream commit 9eb40fa2cd2d1f6829e7b49bb22692f754b9cfe0 ]

of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_tegra()
doesn't do that, so fix it.

Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding: slightly rewrite to avoid inline comparison]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tools: Add Hygon Dhyana support

[ Upstream commit 4787eff3fa88f62fede6ed7afa06477ae6bf984d ]

The tool perf is useful for the performance analysis on the Hygon Dhyana
platform. But right now there is no Hygon support for it to analyze the
KVM guest os data. So add Hygon Dhyana support to it by checking vendor
string to share the code path of AMD.

Signed-off-by: Pu Wen <puwen@hygon.cn>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1542008451-31735-1-git-send-email-puwen@hygon.cn
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

modpost: validate symbol names also in find_elf_symbol

[ Upstream commit 5818c683a619c534c113e1f66d24f636defc29bc ]

If an ARM mapping symbol shares an address with a valid symbol,
find_elf_symbol can currently return the mapping symbol instead, as the
symbol is not validated. This can result in confusing warnings:

  WARNING: vmlinux.o(.text+0x18f4028): Section mismatch in reference
  from the function set_reset_devices() to the variable .init.text:$x.0

This change adds a call to is_valid_name to find_elf_symbol, similarly
to how it's already used in find_elf_symbol2.

Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: OMAP2+: hwmod: Fix some section annotations

[ Upstream commit c10b26abeb53cabc1e6271a167d3f3d396ce0218 ]

When building the kernel with Clang, the following section mismatch
warnings appears:

WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_iclk_autoidle()
The function _setup() references
the function __init _setup_iclk_autoidle().
This is often because _setup lacks a __init
annotation or the annotation of _setup_iclk_autoidle is wrong.

WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_reset()
The function _setup() references
the function __init _setup_reset().
This is often because _setup lacks a __init
annotation or the annotation of _setup_reset is wrong.

WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_postsetup()
The function _setup() references
the function __init _setup_postsetup().
This is often because _setup lacks a __init
annotation or the annotation of _setup_postsetup is wrong.

_setup is used in omap_hwmod_allocate_module, which isn't marked __init
and looks like it shouldn't be, meaning to fix these warnings, those
functions must be moved out of the init section, which this patch does.

Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging: iio: ad7780: update voltage on read

[ Upstream commit 336650c785b62c3bea7c8cf6061c933a90241f67 ]

The ad7780 driver previously did not read the correct device output, as
it read an outdated value set at initialization. It now updates its
voltage on read.

Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging:iio:ad2s90: Make probe handle spi_setup failure

[ Upstream commit b3a3eafeef769c6982e15f83631dcbf8d1794efb ]

Previously, ad2s90_probe ignored the return code from spi_setup, not
handling its possible failure. This patch makes ad2s90_probe check if
the code is an error code and, if so, do the following:

- Call dev_err with an appropriate error message.
- Return the spi_setup's error code.

Note: The 'return ret' statement could be out of the 'if' block, but
this whole block will be moved up in the function in the patch:
'staging:iio:ad2s90: Move device registration to the end of probe'.

Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ptp: check gettime64 return code in PTP_SYS_OFFSET ioctl

[ Upstream commit 83d0bdc7390b890905634186baaa294475cd6a06 ]

If a gettime64 call fails, return the error and avoid copying data back
to user.

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: fsl_lpuart: clear parity enable bit when disable parity

[ Upstream commit 397bd9211fe014b347ca8f95a8f4e1017bac1aeb ]

Current driver only enable parity enable bit and never clear it
when user set the termios. The fix clear the parity enable bit when
PARENB flag is not set in termios->c_cflag.

Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/vc4: ->x_scaling[1] should never be set to VC4_SCALING_NONE

[ Upstream commit 0560054da5673b25d56bea6c57c8d069673af73b ]

For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.

The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).

Fixes: fc04023fafec ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pseries: add of_node_put() in dlpar_detach_node()

[ Upstream commit 5b3f5c408d8cc59b87e47f1ab9803dbd006e4a91 ]

The previous commit, "of: overlay: add missing of_node_get() in
__of_attach_node_sysfs" added a missing of_node_get() to
__of_attach_node_sysfs().  This results in a refcount imbalance
for nodes attached with dlpar_attach_node().  The calling sequence
from dlpar_attach_node() to __of_attach_node_sysfs() is:

   dlpar_attach_node()
      of_attach_node()
         __of_attach_node_sysfs()

For more detailed description of the node refcount, see
commit 68baf692c435 ("powerpc/pseries: Fix of_node_put() underflow
during DLPAR remove").

Tested-by: Alan Tull <atull@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/PCI: Fix Broadcom CNB20LE unintended sign extension (redux)

[ Upstream commit 53bb565fc5439f2c8c57a786feea5946804aa3e9 ]

In the expression "word1 << 16", word1 starts as u16, but is promoted to a
signed int, then sign-extended to resource_size_t, which is probably not
what was intended.  Cast to resource_size_t to avoid the sign extension.

This fixes an identical issue as fixed by commit 0b2d70764bb3 ("x86/PCI:
Fix Broadcom CNB20LE unintended sign extension") back in 2014.

Detected by CoverityScan, CID#138749, 138750 ("Unintended sign extension")

Fixes: 3f6ea84a3035 ("PCI: read memory ranges out of Broadcom CNB20LE host bridge")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dlm: Don't swamp the CPU with callbacks queued during recovery

[ Upstream commit 216f0efd19b9cc32207934fd1b87a45f2c4c593e ]

Before this patch, recovery would cause all callbacks to be delayed,
put on a queue, and afterward they were all queued to the callback
work queue. This patch does the same thing, but occasionally takes
a break after 25 of them so it won't swamp the CPU at the expense
of other RT processes like corosync.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 8808/1: kexec:offline panic_smp_self_stop CPU

[ Upstream commit 82c08c3e7f171aa7f579b231d0abbc1d62e91974 ]

In case panic() and panic() called at the same time on different CPUS.
For example:
CPU 0:
  panic()
     __crash_kexec
       machine_crash_shutdown
         crash_smp_send_stop
       machine_kexec
         BUG_ON(num_online_cpus() > 1);

CPU 1:
  panic()
    local_irq_disable
    panic_smp_self_stop

If CPU 1 calls panic_smp_self_stop() before crash_smp_send_stop(), kdump
fails. CPU1 can't receive the ipi irq, CPU1 will be always online.
To fix this problem, this patch split out the panic_smp_self_stop()
and add set_cpu_online(smp_processor_id(), false).

Signed-off-by: Yufen Wang <wangyufen@huawei.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Correct LCB RJT handling

[ Upstream commit b114d9009d386276bfc3352289fc235781ae3353 ]

When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath9k: dynack: use authentication messages for 'late' ack

[ Upstream commit 3831a2a0010c72e3956020cbf1057a1701a2e469 ]

In order to properly support dynack in ad-hoc mode running
wpa_supplicant, take into account authentication frames for
'late ack' detection. This patch has been tested on devices
mounted on offshore high-voltage stations connected through
~24Km link

Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpu: ipu-v3: image-convert: Prevent race between run and unprepare

[ Upstream commit 819bec35c8c9706185498c9222bd244e0781ad35 ]

Prevent possible race by parallel threads between ipu_image_convert_run()
and ipu_image_convert_unprepare(). This involves setting ctx->aborting
to true unconditionally so that no new job runs can be queued during
unprepare, and holding the ctx->aborting flag until the context is freed.

Note that the "normal" ipu_image_convert_abort() case (e.g. not during
context unprepare) should clear the ctx->aborting flag after aborting
any active run and clearing the context's pending queue. This is because
it should be possible to continue to use the conversion context and queue
more runs after an abort.

Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Intel: mrfld: fix uninitialized variable access

[ Upstream commit 1539c7f23f256120f89f8b9ec53160790bce9ed2 ]

Randconfig testing revealed a very old bug, with gcc-8:

sound/soc/intel/atom/sst/sst_loader.c: In function 'sst_load_fw':
sound/soc/intel/atom/sst/sst_loader.c:357:5: error: 'fw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  if (fw == NULL) {
     ^
sound/soc/intel/atom/sst/sst_loader.c:354:25: note: 'fw' was declared here
  const struct firmware *fw;

We must check the return code of request_firmware() before we look at the
pointer result that may be uninitialized when the function fails.

Fixes: 9012c9544eea ("ASoC: Intel: mrfld - Add DSP load and management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging: iio: adc: ad7280a: handle error from __ad7280_read32()

[ Upstream commit 0559ef7fde67bc6c83c6eb6329dbd6649528263e ]

Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative
error code. This change will ensure that this error is being passed up
in the call stack, so it can be handled.

Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/bufs: Fix Spectre v1 vulnerability

[ Upstream commit a37805098900a6e73a55b3a43b7d3bcd987bb3f4 ]

idx can be indirectly controlled by user-space, hence leading to a
potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

drivers/gpu/drm/drm_bufs.c:1420 drm_legacy_freebufs() warn: potential
spectre issue 'dma->buflist' [r] (local cap)

Fix this by sanitizing idx before using it to index dma->buflist

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016095549.GA23586@embeddedor.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 4.9.155

fanotify: fix handling of events on child sub-directory

commit b469e7e47c8a075cc08bcd1e85d4365134bdcdd5 upstream.

When an event is reported on a sub-directory and the parent inode has
a mark mask with FS_EVENT_ON_CHILD|FS_ISDIR, the event will be sent to
fsnotify() even if the event type is not in the parent mark mask
(e.g. FS_OPEN).

Further more, if that event happened on a mount or a filesystem with
a mount/sb mark that does have that event type in their mask, the "on
child" event will be reported on the mount/sb mark.  That is not
desired, because user will get a duplicate event for the same action.

Note that the event reported on the victim inode is never merged with
the event reported on the parent inode, because of the check in
should_merge(): old_fsn->inode == new_fsn->inode.

Fix this by looking for a match of an actual event type (i.e. not just
FS_ISDIR) in parent's inode mark mask and by not reporting an "on child"
event to group if event type is only found on mount/sb marks.

[backport hint: The bug seems to have always been in fanotify, but this
                patch will only apply cleanly to v4.19.y]

Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
[amir: backport to v4.9]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: don't scan the inode cache before SB_BORN is set

commit 79f546a696bff2590169fb5684e23d65f4d9f591 upstream.

We recently had an oops reported on a 4.14 kernel in
xfs_reclaim_inodes_count() where sb->s_fs_info pointed to garbage
and so the m_perag_tree lookup walked into lala land.  It produces
an oops down this path during the failed mount:

  radix_tree_gang_lookup_tag+0xc4/0x130
  xfs_perag_get_tag+0x37/0xf0
  xfs_reclaim_inodes_count+0x32/0x40
  xfs_fs_nr_cached_objects+0x11/0x20
  super_cache_count+0x35/0xc0
  shrink_slab.part.66+0xb1/0x370
  shrink_node+0x7e/0x1a0
  try_to_free_pages+0x199/0x470
  __alloc_pages_slowpath+0x3a1/0xd20
  __alloc_pages_nodemask+0x1c3/0x200
  cache_grow_begin+0x20b/0x2e0
  fallback_alloc+0x160/0x200
  kmem_cache_alloc+0x111/0x4e0

The problem is that the superblock shrinker is running before the
filesystem structures it depends on have been fully set up. i.e.
the shrinker is registered in sget(), before ->fill_super() has been
called, and the shrinker can call into the filesystem before
fill_super() does it's setup work. Essentially we are exposed to
both use-after-free and use-before-initialisation bugs here.

To fix this, add a check for the SB_BORN flag in super_cache_count.
In general, this flag is not set until ->fs_mount() completes
successfully, so we know that it is set after the filesystem
setup has completed. This matches the trylock_super() behaviour
which will not let super_cache_scan() run if SB_BORN is not set, and
hence will not allow the superblock shrinker from entering the
filesystem while it is being set up or after it has failed setup
and is being torn down.

Cc: stable@kernel.org
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Aaron Lu <aaron.lu@linux.alibaba.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: core: Remove glue dirs from sysfs earlier

commit 726e41097920a73e4c7c33385dcc0debb1281e18 upstream.

For devices with a class, we create a "glue" directory between
the parent device and the new device with the class name.

This directory is never "explicitely" removed when empty however,
this is left to the implicit sysfs removal done by kobject_release()
when the object loses its last reference via kobject_put().

This is problematic because as long as it's not been removed from
sysfs, it is still present in the class kset and in sysfs directory
structure.

The presence in the class kset exposes a use after free bug fixed
by the previous patch, but the presence in sysfs means that until
the kobject is released, which can take a while (especially with
kobject debugging), any attempt at re-creating such as binding a
new device for that class/parent pair, will result in a sysfs
duplicate file name error.

This fixes it by instead doing an explicit kobject_del() when
the glue dir is empty, by keeping track of the number of
child devices of the gluedir.

This is made easy by the fact that all glue dir operations are
done with a global mutex, and there's already a function
(cleanup_glue_dir) called in all the right places taking that
mutex that can be enhanced for this. It appears that this was
in fact the intent of the function, but the implementation was
wrong.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Cc: Guenter Roeck <groeck@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: Always resolve hostname before reconnecting

commit 28eb24ff75c5ac130eb326b3b4d0dcecfc0f427d upstream.

In case a hostname resolves to a different IP address (e.g. long
running mounts), make sure to resolve it every time prior to calling
generic_ip_connect() in reconnect.

Suggested-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Paulo Alcantara <palcantara@suse.de>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: migrate: don't rely on __PageMovable() of newpage after unlocking it

commit e0a352fabce61f730341d119fbedf71ffdb8663f upstream.

We had a race in the old balloon compaction code before b1123ea6d3b3
("mm: balloon: use general non-lru movable page feature") refactored it
that became visible after backporting 195a8c43e93d ("virtio-balloon:
deflate via a page list") without the refactoring.

The bug existed from commit d6d86c0a7f8d ("mm/balloon_compaction:
redesign ballooned pages management") till b1123ea6d3b3 ("mm: balloon:
use general non-lru movable page feature").  d6d86c0a7f8d
("mm/balloon_compaction: redesign ballooned pages management") was
backported to 3.12, so the broken kernels are stable kernels [3.12 -
4.7].

There was a subtle race between dropping the page lock of the newpage in
__unmap_and_move() and checking for __is_movable_balloon_page(newpage).

Just after dropping this page lock, virtio-balloon could go ahead and
deflate the newpage, effectively dequeueing it and clearing PageBalloon,
in turn making __is_movable_balloon_page(newpage) fail.

This resulted in dropping the reference of the newpage via
putback_lru_page(newpage) instead of put_page(newpage), leading to
page->lru getting modified and a !LRU page ending up in the LRU lists.
With 195a8c43e93d ("virtio-balloon: deflate via a page list")
backported, one would suddenly get corrupted lists in
release_pages_balloon():

- WARNING: CPU: 13 PID: 6586 at lib/list_debug.c:59 __list_del_entry+0xa1/0xd0
- list_del corruption. prev->next should be ffffe253961090a0, but was dead000000000100

Nowadays this race is no longer possible, but it is hidden behind very
ugly handling of __ClearPageMovable() and __PageMovable().

__ClearPageMovable() will not make __PageMovable() fail, only
PageMovable().  So the new check (__PageMovable(newpage)) will still
hold even after newpage was dequeued by virtio-balloon.

If anybody would ever change that special handling, the BUG would be
introduced again.  So instead, make it explicit and use the information
of the original isolated page before migration.

This patch can be backported fairly easy to stable kernels (in contrast
to the refactoring).

Link: http://lkml.kernel.org/r/20190129233217.10747-1-david@redhat.com
Fixes: d6d86c0a7f8d ("mm/balloon_compaction: redesign ballooned pages management")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Vratislav Bendel <vbendel@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Vratislav Bendel <vbendel@redhat.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [3.12 - 4.7]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: hwpoison: use do_send_sig_info() instead of force_sig()

commit 6376360ecbe525a9c17b3d081dfd88ba3e4ed65b upstream.

Currently memory_failure() is racy against process's exiting, which
results in kernel crash by null pointer dereference.

The root cause is that memory_failure() uses force_sig() to forcibly
kill asynchronous (meaning not in the current context) processes.  As
discussed in thread https://lkml.org/lkml/2010/6/8/236 years ago for OOM
fixes, this is not a right thing to do.  OOM solves this issue by using
do_send_sig_info() as done in commit d2d393099de2 ("signal:
oom_kill_task: use SEND_SIG_FORCED instead of force_sig()"), so this
patch is suggesting to do the same for hwpoison.  do_send_sig_info()
properly accesses to siglock with lock_task_sighand(), so is free from
the reported race.

I confirmed that the reported bug reproduces with inserting some delay
in kill_procs(), and it never reproduces with this patch.

Note that memory_failure() can send another type of signal using
force_sig_mceerr(), and the reported race shouldn't happen on it because
force_sig_mceerr() is called only for synchronous processes (i.e.
BUS_MCEERR_AR happens only when some process accesses to the corrupted
memory.)

Link: http://lkml.kernel.org/r/20190116093046.GA29835@hori1.linux.bs1.fc.nec.co.jp
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, oom: fix use-after-free in oom_kill_process

commit cefc7ef3c87d02fc9307835868ff721ea12cc597 upstream.

Syzbot instance running on upstream kernel found a use-after-free bug in
oom_kill_process.  On further inspection it seems like the process
selected to be oom-killed has exited even before reaching
read_lock(&tasklist_lock) in oom_kill_process().  More specifically the
tsk->usage is 1 which is due to get_task_struct() in oom_evaluate_task()
and the put_task_struct within for_each_thread() frees the tsk and
for_each_thread() tries to access the tsk.  The easiest fix is to do
get/put across the for_each_thread() on the selected task.

Now the next question is should we continue with the oom-kill as the
previously selected task has exited? However before adding more
complexity and heuristics, let's answer why we even look at the children
of oom-kill selected task? The select_bad_process() has already selected
the worst process in the system/memcg.  Due to race, the selected
process might not be the worst at the kill time but does that matter?
The userspace can use the oom_score_adj interface to prefer children to
be killed before the parent.  I looked at the history but it seems like
this is there before git history.

Link: http://lkml.kernel.org/r/20190121215850.221745-1-shakeelb@google.com
Reported-by: syzbot+7fbbfa368521945f0e3d@syzkaller.appspotmail.com
Fixes: 6b0c81b3be11 ("mm, oom: reduce dependency on tasklist_lock")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/exit.c: release ptraced tasks before zap_pid_ns_processes

commit 8fb335e078378c8426fabeed1ebee1fbf915690c upstream.

Currently, exit_ptrace() adds all ptraced tasks in a dead list, then
zap_pid_ns_processes() waits on all tasks in a current pidns, and only
then are tasks from the dead list released.

zap_pid_ns_processes() can get stuck on waiting tasks from the dead
list.  In this case, we will have one unkillable process with one or
more dead children.

Thanks to Oleg for the advice to release tasks in find_child_reaper().

Link: http://lkml.kernel.org/r/20190110175200.12442-1-avagin@gmail.com
Fixes: 7c8bd2322c7f ("exit: ptrace: shift "reap dead" code from exit_ptrace() to forget_original_parent()")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci-iproc: handle mmc_of_parse() errors during probe

commit 2bd44dadd5bfb4135162322fd0b45a174d4ad5bf upstream.

We need to handle mmc_of_parse() errors during probe.

This finally fixes the wifi regression on Raspberry Pi 3 series.
In error case the wifi chip was permanently in reset because of
the power sequence depending on the deferred probe of the GPIO expander.

Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

platform/x86: asus-nb-wmi: Drop mapping of 0x33 and 0x34 scan codes

[ Upstream commit 71b12beaf12f21a53bfe100795d0797f1035b570 ]

According to Asus firmware engineers, the meaning of these codes is only
to notify the OS that the screen brightness has been turned on/off by
the EC. This does not match the meaning of KEY_DISPLAYTOGGLE /
KEY_DISPLAY_OFF, where userspace is expected to change the display
brightness.

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: asus-nb-wmi: Map 0x35 to KEY_SCREENLOCK

[ Upstream commit b3f2f3799a972d3863d0fdc2ab6287aef6ca631f ]

When the OS registers to handle events from the display off hotkey the
EC will send a notification with 0x35 for every key press, independent
of the backlight state.

The behavior of this key on Windows, with the ATKACPI driver from Asus
installed, is turning off the backlight of all connected displays with a
fading effect, and any cursor input or key press turning the backlight
back on. The key press or cursor input that wakes up the display is also
passed through to the application under the cursor or under focus.

The key that matches this behavior the closest is KEY_SCREENLOCK.

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: Revert "Fix loop in gfs2_rbm_find"

commit e74c98ca2d6ae4376cc15fa2a22483430909d96b upstream.

This reverts commit 2d29f6b96d8f80322ed2dd895bca590491c38d34.

It turns out that the fix can lead to a ~20 percent performance regression
in initial writes to the page cache according to iozone.  Let's revert this
for now to have more time for a proper fix.

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: hibernate: Clean the __hyp_text to PoC after resume

commit f7daa9c8fd191724b9ab9580a7be55cd1a67d799 upstream.

During resume hibernate restores all physical memory. Any memory
that is accessed with the MMU disabled needs to be cleaned to the
PoC.

KVMs __hyp_text was previously ommitted as it runs with the MMU
enabled, but now that the hyp-stub is located in this section,
we must clean __hyp_text too.

This ensures secondary CPUs that come online after hibernate
has finished resuming, and load KVM via the freshly written
hyp-stub see the correct instructions.

Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: hyp-stub: Forbid kprobing of the hyp-stub

commit 8fac5cbdfe0f01254d9d265c6aa1a95f94f58595 upstream.

The hyp-stub is loaded by the kernel's early startup code at EL2
during boot, before KVM takes ownership later. The hyp-stub's
text is part of the regular kernel text, meaning it can be kprobed.

A breakpoint in the hyp-stub causes the CPU to spin in el2_sync_invalid.

Add it to the __hyp_text.

Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: kaslr: ensure randomized quantities are clean also when kaslr is off

commit 8ea235932314311f15ea6cf65c1393ed7e31af70 upstream.

Commit 1598ecda7b23 ("arm64: kaslr: ensure randomized quantities are
clean to the PoC") added cache maintenance to ensure that global
variables set by the kaslr init routine are not wiped clean due to
cache invalidation occurring during the second round of page table
creation.

However, if kaslr_early_init() exits early with no randomization
being applied (either due to the lack of a seed, or because the user
has disabled kaslr explicitly), no cache maintenance is performed,
leading to the same issue we attempted to fix earlier, as far as the
module_alloc_base variable is concerned.

Note that module_alloc_base cannot be initialized statically, because
that would cause it to be subject to a R_AARCH64_RELATIVE relocation,
causing it to be overwritten by the second round of KASLR relocation
processing.

Fixes: f80fb3a3d508 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment

commit 65dbb423cf28232fed1732b779249d6164c5999b upstream.

Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.

Commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:

  cns3xxx_pci_write_config() --> pci_generic_config_write()

cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.

This currently leads to pci_generic_config_write() writing to the wrong
registers.

For instance, upon ath9k module loading:

- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
  located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
  (CACHE_LINE_SIZE)

Fix the bug by removing the alignment in the cns3xxx mapping function.

Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org # v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs/dcache: Fix incorrect nr_dentry_unused accounting in shrink_dcache_sb()

commit 1dbd449c9943e3145148cc893c2461b72ba6fef0 upstream.

The nr_dentry_unused per-cpu counter tracks dentries in both the LRU
lists and the shrink lists where the DCACHE_LRU_LIST bit is set.

The shrink_dcache_sb() function moves dentries from the LRU list to a
shrink list and subtracts the dentry count from nr_dentry_unused.  This
is incorrect as the nr_dentry_unused count will also be decremented in
shrink_dentry_list() via d_shrink_del().

To fix this double decrement, the decrement in the shrink_dcache_sb()
function is taken out.

Fixes: 4e717f5c1083 ("list_lru: remove special case function list_lru_dispose_all."
Cc: stable@kernel.org
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: Do not count -ENODATA as failure for query directory

commit 8e6e72aeceaaed5aeeb1cb43d3085de7ceb14f79 upstream.

Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipvlan, l3mdev: fix broken l3s mode wrt local routes

[ Upstream commit d5256083f62e2720f75bb3c5a928a0afe47d6bc3 ]

While implementing ipvlan l3 and l3s mode for kubernetes CNI plugin,
I ran into the issue that while l3 mode is working fine, l3s mode
does not have any connectivity to kube-apiserver and hence all pods
end up in Error state as well. The ipvlan master device sits on
top of a bond device and hostns traffic to kube-apiserver (also running
in hostns) is DNATed from 10.152.183.1:443 to 139.178.29.207:37573
where the latter is the address of the bond0. While in l3 mode, a
curl to https://10.152.183.1:443 or to https://139.178.29.207:37573
works fine from hostns, neither of them do in case of l3s. In the
latter only a curl to https://127.0.0.1:37573 appeared to work where
for local addresses of bond0 I saw kernel suddenly starting to emit
ARP requests to query HW address of bond0 which remained unanswered
and neighbor entries in INCOMPLETE state. These ARP requests only
happen while in l3s.

Debugging this further, I found the issue is that l3s mode is piggy-
backing on l3 master device, and in this case local routes are using
l3mdev_master_dev_rcu(dev) instead of net->loopback_dev as per commit
f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev
if relevant") and 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be
a loopback"). I found that reverting them back into using the
net->loopback_dev fixed ipvlan l3s connectivity and got everything
working for the CNI.

Now judging from 4fbae7d83c98 ("ipvlan: Introduce l3s mode") and the
l3mdev paper in [0] the only sole reason why ipvlan l3s is relying
on l3 master device is to get the l3mdev_ip_rcv() receive hook for
setting the dst entry of the input route without adding its own
ipvlan specific hacks into the receive path, however, any l3 domain
semantics beyond just that are breaking l3s operation. Note that
ipvlan also has the ability to dynamically switch its internal
operation from l3 to l3s for all ports via ipvlan_set_port_mode()
at runtime. In any case, l3 vs l3s soley distinguishes itself by
'de-confusing' netfilter through switching skb->dev to ipvlan slave
device late in NF_INET_LOCAL_IN before handing the skb to L4.

Minimal fix taken here is to add a IFF_L3MDEV_RX_HANDLER flag which,
if set from ipvlan setup, gets us only the wanted l3mdev_l3_rcv() hook
without any additional l3mdev semantics on top. This should also have
minimal impact since dev->priv_flags is already hot in cache. With
this set, l3s mode is working fine and I also get things like
masquerading pod traffic on the ipvlan master properly working.

  [0] https://netdevconf.org/1.2/papers/ahern-what-is-l3mdev-paper.pdf

Fixes: f5a0aab84b74 ("net: ipv4: dst for local input routes should use l3mdev if relevant")
Fixes: 5f02ce24c269 ("net: l3mdev: Allow the l3mdev to be a loopback")
Fixes: 4fbae7d83c98 ("ipvlan: Introduce l3s mode")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Martynas Pumputis <m@lambda.lt>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: fix reading optional fields of L2TPv3

[ Upstream commit 4522a70db7aa5e77526a4079628578599821b193 ]

Use pskb_may_pull() to make sure the optional fields are in skb linear
parts, so we can safely read them later.

It's easy to reproduce the issue with a net driver that supports paged
skb data. Just create a L2TPv3 over IP tunnel and then generates some
network traffic.
Once reproduced, rx err in /sys/kernel/debug/l2tp/tunnels will increase.

Changes in v4:
1. s/l2tp_v3_pull_opt/l2tp_v3_ensure_opt_in_linear/
2. s/tunnel->version != L2TP_HDR_VER_2/tunnel->version == L2TP_HDR_VER_3/
3. Add 'Fixes' in commit messages.

Changes in v3:
1. To keep consistency, move the code out of l2tp_recv_common.
2. Use "net" instead of "net-next", since this is a bug fix.

Changes in v2:
1. Only fix L2TPv3 to make code simple.
   To fix both L2TPv3 and L2TPv2, we'd better refactor l2tp_recv_common.
   It's complicated to do so.
2. Reloading pointers after pskb_may_pull

Fixes: f7faffa3ff8e ("l2tp: Add L2TPv3 protocol support")
Fixes: 0d76751fad77 ("l2tp: Add L2TPv3 IP encapsulation (no UDP) support")
Fixes: a32e0eec7042 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6")
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: remove l2specific_len dependency in l2tp_core

commit 62e7b6a57c7b9bf3c6fd99418eeec05b08a85c38 upstream.

Remove l2specific_len dependency while building l2tpv3 header or
parsing the received frame since default L2-Specific Sublayer is
always four bytes long and we don't need to rely on a user supplied
value.
Moreover in l2tp netlink code there are no sanity checks to
enforce the relation between l2specific_len and l2specific_type,
so sending a malformed netlink message is possible to set
l2specific_type to L2TP_L2SPECTYPE_DEFAULT (or even
L2TP_L2SPECTYPE_NONE) and set l2specific_len to a value greater than
4 leaking memory on the wire and sending corrupted frames.

Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: Allow MAC invalidation while spoofchk is ON

[ Upstream commit 9d2cbdc5d334967c35b5f58c7bf3208e17325647 ]

Prior to this patch the driver prohibited spoof checking on invalid MAC.
Now the user can set this configuration if it wishes to.

This is required since libvirt might invalidate the VF Mac by setting it
to zero, while spoofcheck is ON.

Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ucc_geth: Reset BQL queue when stopping device

[ Upstream commit e15aa3b2b1388c399c1a2ce08550d2cc4f7e3e14 ]

After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.

Co-authored-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/rose: fix NULL ax25_cb kernel panic

[ Upstream commit b0cf029234f9b18e10703ba5147f0389c382bccc ]

When an internally generated frame is handled by rose_xmit(),
rose_route_frame() is called:

        if (!rose_route_frame(skb, NULL)) {
                dev_kfree_skb(skb);
                stats->tx_errors++;
                return NETDEV_TX_OK;
        }

We have the same code sequence in Net/Rom where an internally generated
frame is handled by nr_xmit() calling nr_route_frame(skb, NULL).
However, in this function NULL argument is tested while it is not in
rose_route_frame().
Then kernel panic occurs later on when calling ax25cmp() with a NULL
ax25_cb argument as reported many times and recently with syzbot.

We need to test if ax25 is NULL before using it.

Testing:
Built kernel with CONFIG_ROSE=y.

Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+1a2c456a1ea08fa5b5f7@syzkaller.appspotmail.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Bernard Pidoux <f6bvp@free.fr>
Cc: linux-hams@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netrom: switch to sock timer API

[ Upstream commit 63346650c1a94a92be61a57416ac88c0a47c4327 ]

sk_reset_timer() and sk_stop_timer() properly handle
sock refcnt for timer function. Switching to them
could fix a refcounting bug reported by syzbot.

Reported-and-tested-by: syzbot+defa700d16f1bd1b9a05@syzkaller.appspotmail.com
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_core: Add masking for a few queries on HCA caps

[ Upstream commit a40ded6043658444ee4dd6ee374119e4e98b33fc ]

Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned.  In addition some reserved bits were wrongly read.  Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.

Fixes: ab9c17a009ee ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb654bec ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

l2tp: copy 4 more bytes to linear part if necessary

[ Upstream commit 91c524708de6207f59dd3512518d8a1c7b434ee3 ]

The size of L2TPv2 header with all optional fields is 14 bytes.
l2tp_udp_recv_core only moves 10 bytes to the linear part of a
skb. This may lead to l2tp_recv_common read data outside of a skb.

This patch make sure that there is at least 14 bytes in the linear
part of a skb to meet the maximum need of l2tp_udp_recv_core and
l2tp_recv_common. The minimum size of both PPP HDLC-like frame and
Ethernet frame is larger than 14 bytes, so we are safe to do so.

Also remove L2TP_HDR_SIZE_NOSEQ, it is unused now.

Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: Consider sk_bound_dev_if when binding a socket to an address

[ Upstream commit c5ee066333ebc322a24a00a743ed941a0c68617e ]

IPv6 does not consider if the socket is bound to a device when binding
to an address. The result is that a socket can be bound to eth0 and then
bound to the address of eth1. If the device is a VRF, the result is that
a socket can only be bound to an address in the default VRF.

Resolve by considering the device if sk_bound_dev_if is set.

This problem exists from the beginning of git history.

Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: add the fsnotify call to vfs_iter_write

A bug has been discovered when redirecting splice output to regular files
on EXT4 and tmpfs. Other filesystems might be affected.
This commit fixes the issue for stable series kernel, using one of the
change introduced during the rewrite and refactoring of vfs_iter_write in
4.13, specifically in the
commit abbb65899aec ("fs: implement vfs_iter_write using do_iter_write").

This issue affects v4.4 and v4.9 stable series of kernels.

Without this fix for v4.4 and v4.9 stable, the following upstream commits
(and their dependencies would need to be backported):
* commit abbb65899aec ("fs: implement vfs_iter_write using do_iter_write")
* commit 18e9710ee59c ("fs: implement vfs_iter_read using do_iter_read")
* commit edab5fe38c2c
  ("fs: move more code into do_iter_read/do_iter_write")
* commit 19c735868dd0 ("fs: remove __do_readv_writev")
* commit 26c87fb7d10d ("fs: remove do_compat_readv_writev")
* commit 251b42a1dc64 ("fs: remove do_readv_writev")

as well as the following dependencies:
* commit bb7462b6fd64
  ("vfs: use helpers for calling f_op->{read,write}_iter()")
* commit 0f78d06ac1e9
  ("vfs: pass type instead of fn to do_{loop,iter}_readv_writev()")
* commit 7687a7a4435f
  ("vfs: extract common parts of {compat_,}do_readv_writev()")

In order to reduce the changes, this commit uses only the part of
commit abbb65899aec ("fs: implement vfs_iter_write using do_iter_write")
that fixes the issue.

This issue and the reproducer can be found on
https://bugzilla.kernel.org/show_bug.cgi?id=85381

Reported-by: Richard Li <richardpku@gmail.com>
Reported-by: Chad Miller <millchad@amazon.com>
Reviewed-by: Stefan Nuernberger <snu@amazon.de>
Reviewed-by: Frank Becker <becke@amazon.de>
Signed-off-by: Jimmy Durand Wesolowski <jdw@amazon.de>

Fix "net: ipv4: do not handle duplicate fragments as overlapping"

ade446403bfb ("net: ipv4: do not handle duplicate fragments as
overlapping") was backported to many stable trees, but it had a problem
that was "accidentally" fixed by the upstream commit 0ff89efb5246 ("ip:
fail fast on IP defrag errors")

This is the fixup for that problem as we do not want the larger patch in
the older stable trees.

Fixes: ade446403bfb ("net: ipv4: do not handle duplicate fragments as overlapping")
Reported-by: Ivan Babrou <ivan@cloudflare.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.9.154

btrfs: dev-replace: go back to suspended state if target device is missing

commit 0d228ece59a35a9b9e8ff0d40653234a6d90f61e upstream.

At the time of forced unmount we place the running replace to
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state, so when the system comes
back and expect the target device is missing.

Then let the replace state continue to be in
BTRFS_IOCTL_DEV_REPLACE_STATE_SUSPENDED state instead of
BTRFS_IOCTL_DEV_REPLACE_STATE_STARTED as there isn't any matching scrub
running as part of replace.

Fixes: e93c89c1aaaa ("Btrfs: add new sources for device replace code")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: fix error handling in btrfs_dev_replace_start

commit 5c06147128fbbdf7a84232c5f0d808f53153defe upstream.

When we fail to start a transaction in btrfs_dev_replace_start, we leave
dev_replace->replace_start set to STARTED but clear ->srcdev and
->tgtdev.  Later, that can result in an Oops in
btrfs_dev_replace_progress when having state set to STARTED or SUSPENDED
implies that ->srcdev is valid.

Also fix error handling when the state is already STARTED or SUSPENDED
while starting.  That, too, will clear ->srcdev and ->tgtdev even though
it doesn't own them.  This should be an impossible case to hit since we
should be protected by the BTRFS_FS_EXCL_OP bit being set.  Let's add an
ASSERT there while we're at it.

Fixes: e93c89c1aaaaa (Btrfs: add new sources for device replace code)
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

f2fs: read page index before freeing

commit 0ea295dd853e0879a9a30ab61f923c26be35b902 upstream.

The function truncate_node frees the page with f2fs_put_page. However,
the page index is read after that. So, the patch reads the index before
freeing the page.

Fixes: bf39c00a9a7f ("f2fs: drop obsolete node page when it is truncated")
Cc: <stable@vger.kernel.org>
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmet-rdma: fix null dereference under heavy load

commit 5cbab6303b4791a3e6713dfe2c5fda6a867f9adc upstream.

Under heavy load if we don't have any pre-allocated rsps left, we
dynamically allocate a rsp, but we are not actually allocating memory
for nvme_completion (rsp->req.rsp). In such a case, accessing pointer
fields (req->rsp->status) in nvmet_req_init() will result in crash.

To fix this, allocate the memory for nvme_completion by calling
nvmet_rdma_alloc_rsp()

Fixes: 8407879c("nvmet-rdma:fix possible bogus dereference under heavy load")

Cc: <stable@vger.kernel.org>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmet-rdma: Add unlikely for response allocated check

commit ad1f824948e4ed886529219cf7cd717d078c630d upstream.

Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/smp: Fix calling smp_call_ipl_cpu() from ipl CPU

commit 60f1bf29c0b2519989927cae640cd1f50f59dc7f upstream.

When calling smp_call_ipl_cpu() from the IPL CPU, we will try to read
from pcpu_devices->lowcore. However, due to prefixing, that will result
in reading from absolute address 0 on that CPU. We have to go via the
actual lowcore instead.

This means that right now, we will read lc->nodat_stack == 0 and
therfore work on a very wrong stack.

This BUG essentially broke rebooting under QEMU TCG (which will report
a low address protection exception). And checking under KVM, it is
also broken under KVM. With 1 VCPU it can be easily triggered.

:/# echo 1 > /proc/sys/kernel/sysrq
:/# echo b > /proc/sysrq-trigger
[   28.476745] sysrq: SysRq : Resetting
[   28.476793] Kernel stack overflow.
[   28.476817] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[   28.476820] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[   28.476826] Krnl PSW : 0400c00180000000 0000000000115c0c (pcpu_delegate+0x12c/0x140)
[   28.476861]            R:0 T:1 IO:0 EX:0 Key:0 M:0 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
[   28.476863] Krnl GPRS: ffffffffffffffff 0000000000000000 000000000010dff8 0000000000000000
[   28.476864]            0000000000000000 0000000000000000 0000000000ab7090 000003e0006efbf0
[   28.476864]            000000000010dff8 0000000000000000 0000000000000000 0000000000000000
[   28.476865]            000000007fffc000 0000000000730408 000003e0006efc58 0000000000000000
[   28.476887] Krnl Code: 0000000000115bfe: 4170f000            la      %r7,0(%r15)
[   28.476887]            0000000000115c02: 41f0a000            la      %r15,0(%r10)
[   28.476887]           #0000000000115c06: e370f0980024        stg     %r7,152(%r15)
[   28.476887]           >0000000000115c0c: c0e5fffff86e        brasl   %r14,114ce8
[   28.476887]            0000000000115c12: 41f07000            la      %r15,0(%r7)
[   28.476887]            0000000000115c16: a7f4ffa8            brc     15,115b66
[   28.476887]            0000000000115c1a: 0707                bcr     0,%r7
[   28.476887]            0000000000115c1c: 0707                bcr     0,%r7
[   28.476901] Call Trace:
[   28.476902] Last Breaking-Event-Address:
[   28.476920]  [<0000000000a01c4a>] arch_call_rest_init+0x22/0x80
[   28.476927] Kernel panic - not syncing: Corrupt kernel stack, can't continue.
[   28.476930] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[   28.476932] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[   28.476932] Call Trace:

Fixes: 2f859d0dad81 ("s390/smp: reduce size of struct pcpu")
Cc: stable@vger.kernel.org # 4.0+
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size

commit 8208d1708b88b412ca97f50a6d951242c88cbbac upstream.

The way we allocate events works fine in most cases, except
when multiple PCI devices share an ITS-visible DevID, and that
one of them is trying to use MultiMSI allocation.

In that case, our allocation is not guaranteed to be zero-based
anymore, and we have to make sure we allocate it on a boundary
that is compatible with the PCI Multi-MSI constraints.

Fix this by allocating the full region upfront instead of iterating
over the number of MSIs. MSI-X are always allocated one by one,
so this shouldn't change anything on that front.

Fixes: b48ac83d6bbc2 ("irqchip: GICv3: ITS: MSI support")
Cc: stable@vger.kernel.org
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[ardb: rebased onto v4.9.153, should apply cleanly onto v4.4.y as well]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>

perf unwind: Take pgoff into account when reporting elf to libdwfl

[ Upstream commit 1fe627da30331024f453faef04d500079b901107 ]

libdwfl parses an ELF file itself and creates mappings for the
individual sections. perf on the other hand sees raw mmap events which
represent individual sections. When we encounter an address pointing
into a mapping with pgoff != 0, we must take that into account and
report the file at the non-offset base address.

This fixes unwinding with libdwfl in some cases. E.g. for a file like:

```

using namespace std;

mutex g_mutex;

double worker()
{
    lock_guard<mutex> guard(g_mutex);
    uniform_real_distribution<double> uniform(-1E5, 1E5);
    default_random_engine engine;
    double s = 0;
    for (int i = 0; i < 1000; ++i) {
        s += norm(complex<double>(uniform(engine), uniform(engine)));
    }
    cout << s << endl;
    return s;
}

int main()
{
    vector<std::future<double>> results;
    for (int i = 0; i < 10000; ++i) {
        results.push_back(async(launch::async, worker));
    }
    return 0;
}
```

Compile it with `g++ -g -O2 -lpthread cpp-locking.cpp  -o cpp-locking`,
then record it with `perf record --call-graph dwarf -e
sched:sched_switch`.

When you analyze it with `perf script` and libunwind, you should see:

```
cpp-locking 20038 [005] 54830.236589: sched:sched_switch: prev_comm=cpp-locking prev_pid=20038 prev_prio=120 prev_state=T ==> next_comm=swapper/5 next_pid=0 next_prio=120
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1670208 schedule+0x28 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb16737cc rwsem_down_read_failed+0xec (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1665e04 call_rwsem_down_read_failed+0x14 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1672a03 down_read+0x13 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb106bd85 __do_page_fault+0x445 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb18015f5 page_fault+0x45 (/lib/modules/4.14.78-1-lts/build/vmlinux)
            7f38e4252591 new_heap+0x101 (/usr/lib/libc-2.28.so)
            7f38e4252d0b arena_get2.part.4+0x2fb (/usr/lib/libc-2.28.so)
            7f38e4255b1c tcache_init.part.6+0xec (/usr/lib/libc-2.28.so)
            7f38e42569e5 __GI___libc_malloc+0x115 (inlined)
            7f38e4241790 __GI__IO_file_doallocate+0x90 (inlined)
            7f38e424fbbf __GI__IO_doallocbuf+0x4f (inlined)
            7f38e424ee47 __GI__IO_file_overflow+0x197 (inlined)
            7f38e424df36 _IO_new_file_xsputn+0x116 (inlined)
            7f38e4242bfb __GI__IO_fwrite+0xdb (inlined)
            7f38e463fa6d std::basic_streambuf<char, std::char_traits<char> >::sputn(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> >::_M_put(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::__write<char>(std::ostreambuf_iterator<char, std::char_traits<char> >, char const*, int)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::_M_insert_float<double>(std::ostreambuf_iterator<c>
            7f38e464bd70 std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::put(std::ostreambuf_iterator<char, std::char_traits<char> >, std::ios_base&, char, double) const+0x90 (inl>
            7f38e464bd70 std::ostream& std::ostream::_M_insert<double>(double)+0x90 (/usr/lib/libstdc++.so.6.0.25)
            563b9cb502f7 std::ostream::operator<<(double)+0xb7 (inlined)
            563b9cb502f7 worker()+0xb7 (/ssd/milian/projects/kdab/rnd/hotspot/build/tests/test-clients/cpp-locking/cpp-locking)
            563b9cb506fb double std::__invoke_impl<double, double (*)()>(std::__invoke_other, double (*&&)())+0x2b (inlined)
            563b9cb506fb std::__invoke_result<double (*)()>::type std::__invoke<double (*)()>(double (*&&)())+0x2b (inlined)
            563b9cb506fb decltype (__invoke((_S_declval<0ul>)())) std::thread::_Invoker<std::tuple<double (*)()> >::_M_invoke<0ul>(std::_Index_tuple<0ul>)+0x2b (inlined)
            563b9cb506fb std::thread::_Invoker<std::tuple<double (*)()> >::operator()()+0x2b (inlined)
            563b9cb506fb std::__future_base::_Task_setter<std::unique_ptr<std::__future_base::_Result<double>, std::__future_base::_Result_base::_Deleter>, std::thread::_Invoker<std::tuple<double (*)()> >, dou>
            563b9cb506fb std::_Function_handler<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> (), std::__future_base::_Task_setter<std::unique_ptr<std::__future_>
            563b9cb507e8 std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>::operator()() const+0x28 (inlined)
            563b9cb507e8 std::__future_base::_State_baseV2::_M_do_set(std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>*, bool*)+0x28 (/ssd/milian/>
            7f38e46d24fe __pthread_once_slow+0xbe (/usr/lib/libpthread-2.28.so)
            563b9cb51149 __gthread_once+0xe9 (inlined)
            563b9cb51149 void std::call_once<void (std::__future_base::_State_baseV2::*)(std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>*, bool*)>
            563b9cb51149 std::__future_base::_State_baseV2::_M_set_result(std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>, bool)+0xe9 (inlined)
            563b9cb51149 std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<double (*)()> >&&)::{lambda()#1}::op>
            563b9cb51149 void std::__invoke_impl<void, std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<double>
            563b9cb51149 std::__invoke_result<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<double (*)()> >>
            563b9cb51149 decltype (__invoke((_S_declval<0ul>)())) std::thread::_Invoker<std::tuple<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_>
            563b9cb51149 std::thread::_Invoker<std::tuple<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<dou>
            563b9cb51149 std::thread::_State_impl<std::thread::_Invoker<std::tuple<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread>
            7f38e45f0062 execute_native_thread_routine+0x12 (/usr/lib/libstdc++.so.6.0.25)
            7f38e46caa9c start_thread+0xfc (/usr/lib/libpthread-2.28.so)
            7f38e42ccb22 __GI___clone+0x42 (inlined)
```

Before this patch, using libdwfl, you would see:

```
cpp-locking 20038 [005] 54830.236589: sched:sched_switch: prev_comm=cpp-locking prev_pid=20038 prev_prio=120 prev_state=T ==> next_comm=swapper/5 next_pid=0 next_prio=120
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1670208 schedule+0x28 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb16737cc rwsem_down_read_failed+0xec (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1665e04 call_rwsem_down_read_failed+0x14 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1672a03 down_read+0x13 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb106bd85 __do_page_fault+0x445 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb18015f5 page_fault+0x45 (/lib/modules/4.14.78-1-lts/build/vmlinux)
            7f38e4252591 new_heap+0x101 (/usr/lib/libc-2.28.so)
        a041161e77950c5c [unknown] ([unknown])
```

With this patch applied, we get a bit further in unwinding:

```
cpp-locking 20038 [005] 54830.236589: sched:sched_switch: prev_comm=cpp-locking prev_pid=20038 prev_prio=120 prev_state=T ==> next_comm=swapper/5 next_pid=0 next_prio=120
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1670208 schedule+0x28 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb16737cc rwsem_down_read_failed+0xec (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1665e04 call_rwsem_down_read_failed+0x14 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1672a03 down_read+0x13 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb106bd85 __do_page_fault+0x445 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb18015f5 page_fault+0x45 (/lib/modules/4.14.78-1-lts/build/vmlinux)
            7f38e4252591 new_heap+0x101 (/usr/lib/libc-2.28.so)
            7f38e4252d0b arena_get2.part.4+0x2fb (/usr/lib/libc-2.28.so)
            7f38e4255b1c tcache_init.part.6+0xec (/usr/lib/libc-2.28.so)
            7f38e42569e5 __GI___libc_malloc+0x115 (inlined)
            7f38e4241790 __GI__IO_file_doallocate+0x90 (inlined)
            7f38e424fbbf __GI__IO_doallocbuf+0x4f (inlined)
            7f38e424ee47 __GI__IO_file_overflow+0x197 (inlined)
            7f38e424df36 _IO_new_file_xsputn+0x116 (inlined)
            7f38e4242bfb __GI__IO_fwrite+0xdb (inlined)
            7f38e463fa6d std::basic_streambuf<char, std::char_traits<char> >::sputn(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> >::_M_put(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::__write<char>(std::ostreambuf_iterator<char, std::char_traits<char> >, char const*, int)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::_M_insert_float<double>(std::ostreambuf_iterator<c>
            7f38e464bd70 std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::put(std::ostreambuf_iterator<char, std::char_traits<char> >, std::ios_base&, char, double) const+0x90 (inl>
            7f38e464bd70 std::ostream& std::ostream::_M_insert<double>(double)+0x90 (/usr/lib/libstdc++.so.6.0.25)
            563b9cb502f7 std::ostream::operator<<(double)+0xb7 (inlined)
            563b9cb502f7 worker()+0xb7 (/ssd/milian/projects/kdab/rnd/hotspot/build/tests/test-clients/cpp-locking/cpp-locking)
        6eab825c1ee3e4ff [unknown] ([unknown])
```

Note that the backtrace is still stopping too early, when compared to
the nice results obtained via libunwind. It's unclear so far what the
reason for that is.

Committer note:

Further comment by Milian on the thread started on the Link: tag below:

 ---
The remaining issue is due to a bug in elfutils:

https://sourceware.org/ml/elfutils-devel/2018-q4/msg00089.html

With both patches applied, libunwind and elfutils produce the same output for
the above scenario.
 ---

Signed-off-by: Milian Wolff <milian.wolff@kdab.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20181029141644.3907-1-milian.wolff@kdab.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf unwind: Unwind with libdw doesn't take symfs into account

[ Upstream commit 3d20c6246690219881786de10d2dda93f616d0ac ]

Path passed to libdw for unwinding doesn't include symfs path
if specified, so unwinding fails because ELF file is not found.

Similar to unwinding with libunwind, pass symsrc_filename instead
of long_name. If there is no symsrc_filename, fallback to long_name.

Signed-off-by: Martin Vuille <jpmv27@aim.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20180211212420.18388-1-jpmv27@aim.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vt: invoke notifier on screen size change

commit 0c9b1965faddad7534b6974b5b36c4ad37998f8e upstream.

User space using poll() on /dev/vcs devices are not awaken when a
screen size change occurs. Let's fix that.

Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: bcm: check timer values before ktime conversion

commit 93171ba6f1deffd82f381d36cb13177872d023f6 upstream.

Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup()
when the conversion into ktime multiplies the given value with NSEC_PER_USEC
(1000).

Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2

Add a check for the given tv_usec, so that the value stays below one second.
Additionally limit the tv_sec value to a reasonable value for CAN related
use-cases of 400 days and ensure all values to be positive.

Reported-by: Kyungtae Kim <kt0755@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26
Tested-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: dev: __can_get_echo_skb(): fix bogous check for non-existing skb by removing it

commit 7b12c8189a3dc50638e7d53714c88007268d47ef upstream.

This patch revert commit 7da11ba5c506
("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")

After introduction of this change we encountered following new error
message on various i.MX plattforms (flexcan):

| flexcan 53fc8000.can can0: __can_get_echo_skb: BUG! Trying to echo non
| existing skb: can_priv::echo_skb[0]

The introduction of the message was a mistake because
priv->echo_skb[idx] = NULL is a perfectly valid in following case: If
CAN_RAW_LOOPBACK is disabled (setsockopt) in applications, the pkt_type
of the tx skb's given to can_put_echo_skb is set to PACKET_LOOPBACK. In
this case can_put_echo_skb will not set priv->echo_skb[idx]. It is
therefore kept NULL.

As additional argument for revert: The order of check and usage of idx
was changed. idx is used to access an array element before checking it's
boundaries.

Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Fixes: 7da11ba5c506 ("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/kaslr: Fix incorrect i8254 outb() parameters

commit 7e6fc2f50a3197d0e82d1c0e86282976c9e6c8a4 upstream.

The outb() function takes parameters value and port, in that order.  Fix
the parameters used in the kalsr i8254 fallback code.

Fixes: 5bfce5ef55cb ("x86, kaslr: Provide randomness functions")
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: linux@endlessm.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190107034024.15005-1-drake@endlessm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/selftests/pkeys: Fork() to check for state being preserved

commit e1812933b17be7814f51b6c310c5d1ced7a9a5f5 upstream.

There was a bug where the per-mm pkey state was not being preserved across
fork() in the child.  fork() is performed in the pkey selftests, but all of
the pkey activity is performed in the parent.  The child does not perform
any actions sensitive to pkey state.

To make the test more sensitive to these kinds of bugs, add a fork() where
the parent exits, and execution continues in the child.

To achieve this let the key exhaustion test not terminate at the first
allocation failure and fork after 2*NR_PKEYS loops and continue in the
child.

Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: peterz@infradead.org
Cc: mpe@ellerman.id.au
Cc: will.deacon@arm.com
Cc: luto@kernel.org
Cc: jroedel@suse.de
Cc: stable@vger.kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20190102215657.585704B7@viggo.jf.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Fix single-step debugging

commit 5cc244a20b86090c087073c124284381cdf47234 upstream.

The single-step debugging of KVM guests on x86 is broken: if we run
gdb 'stepi' command at the breakpoint when the guest interrupts are
enabled, RIP always jumps to native_apic_mem_write(). Then other
nasty effects follow.

Long investigation showed that on Jun 7, 2017 the
commit c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
introduced the kvm_run.debug corruption: kvm_vcpu_do_singlestep() can
be called without X86_EFLAGS_TF set.

Let's fix it. Please consider that for -stable.

Signed-off-by: Alexander Popov <alex.popov@linux.com>
Cc: stable@vger.kernel.org
Fixes: c8401dda2f0a00cd25c0 ("KVM: x86: fix singlestepping over syscall")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm thin: fix passdown_double_checking_shared_status()

commit d445bd9cec1a850c2100fcf53684c13b3fd934f2 upstream.

Commit 00a0ea33b495 ("dm thin: do not queue freed thin mapping for next
stage processing") changed process_prepared_discard_passdown_pt1() to
increment all the blocks being discarded until after the passdown had
completed to avoid them being prematurely reused.

IO issued to a thin device that breaks sharing with a snapshot, followed
by a discard issued to snapshot(s) that previously shared the block(s),
results in passdown_double_checking_shared_status() being called to
iterate through the blocks double checking their reference count is zero
and issuing the passdown if so.  So a side effect of commit 00a0ea33b495
is passdown_double_checking_shared_status() was broken.

Fix this by checking if the block reference count is greater than 1.
Also, rename dm_pool_block_is_used() to dm_pool_block_is_shared().

Fixes: 00a0ea33b495 ("dm thin: do not queue freed thin mapping for next stage processing")
Cc: stable@vger.kernel.org # 4.9+
Reported-by: ryan.p.norwood@gmail.com
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

acpi/nfit: Fix command-supported detection

commit 11189c1089da413aa4b5fd6be4c4d47c78968819 upstream.

The _DSM function number validation only happens to succeed when the
generic Linux command number translation corresponds with a
DSM-family-specific function number. This breaks NVDIMM-N
implementations that correctly implement _LSR, _LSW, and _LSI, but do
not happen to publish support for DSM function numbers 4, 5, and 6.

Recall that the support for _LS{I,R,W} family of methods results in the
DIMM being marked as supporting those command numbers at
acpi_nfit_register_dimms() time. The DSM function mask is only used for
ND_CMD_CALL support of non-NVDIMM_FAMILY_INTEL devices.

Fixes: 31eca76ba2fc ("nfit, libnvdimm: limited/whitelisted dimm command...")
Cc: <stable@vger.kernel.org>
Link: https://github.com/pmem/ndctl/issues/78
Reported-by: Sujith Pandel <sujith_pandel@dell.com>
Tested-by: Sujith Pandel <sujith_pandel@dell.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

acpi/nfit: Block function zero DSMs

commit 5e9e38d0db1d29efed1dd4cf9a70115d33521be7 upstream.

In preparation for using function number 0 as an error value, prevent it
from being considered a valid function value by acpi_nfit_ctl().

Cc: <stable@vger.kernel.org>
Cc: stuart hayes <stuart.w.hayes@gmail.com>
Fixes: e02fb7264d8a ("nfit: add Microsoft NVDIMM DSM command set...")
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: uinput - fix undefined behavior in uinput_validate_absinfo()

commit d77651a227f8920dd7ec179b84e400cce844eeb3 upstream.

An integer overflow may arise in uinput_validate_absinfo() if "max - min"
can't be represented by an "int". We should check for overflow before
trying to use the result.

Reported-by: Kyungtae Kim <kt0755@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

compiler.h: enable builtin overflow checkers and add fallback code

commit f0907827a8a9152aedac2833ed1b674a7b2a44f2 upstream.

This adds wrappers for the __builtin overflow checkers present in gcc
5.1+ as well as fallback implementations for earlier compilers. It's not
that easy to implement the fully generic __builtin_X_overflow(T1 a, T2
b, T3 *d) in macros, so the fallback code assumes that T1, T2 and T3 are
the same. We obviously don't want the wrappers to have different
semantics depending on $GCC_VERSION, so we also insist on that even when
using the builtins.

There are a few problems with the 'a+b < a' idiom for checking for
overflow: For signed types, it relies on undefined behaviour and is
not actually complete (it doesn't check underflow;
e.g. INT_MIN+INT_MIN == 0 isn't caught). Due to type promotion it
is wrong for all types (signed and unsigned) narrower than
int. Similarly, when a and b does not have the same type, there are
subtle cases like

  u32 a;

  if (a + sizeof(foo) < a)
    return -EOVERFLOW;
  a += sizeof(foo);

where the test is always false on 64 bit platforms. Add to that that it
is not always possible to determine the types involved at a glance.

The new overflow.h is somewhat bulky, but that's mostly a result of
trying to be type-generic, complete (e.g. catching not only overflow
but also signed underflow) and not relying on undefined behaviour.

Linus is of course right [1] that for unsigned subtraction a-b, the
right way to check for overflow (underflow) is "b > a" and not
"__builtin_sub_overflow(a, b, &d)", but that's just one out of six cases
covered here, and included mostly for completeness.

So is it worth it? I think it is, if nothing else for the documentation
value of seeing

  if (check_add_overflow(a, b, &d))
    return -EGOAWAY;
  do_stuff_with(d);

instead of the open-coded (and possibly wrong and/or incomplete and/or
UBsan-tickling)

  if (a+b < a)
    return -EGOAWAY;
  do_stuff_with(a+b);

While gcc does recognize the 'a+b < a' idiom for testing unsigned add
overflow, it doesn't do nearly as good for unsigned multiplication
(there's also no single well-established idiom). So using
check_mul_overflow in kcalloc and friends may also make gcc generate
slightly better code.

[1] https://lkml.org/lkml/2015/11/2/658

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: xpad - add support for SteelSeries Stratus Duo

commit fe2bfd0d40c935763812973ce15f5764f1c12833 upstream.

Add support for the SteelSeries Stratus Duo, a wireless Xbox 360
controller. The Stratus Duo ships with a USB dongle to enable wireless
connectivity, but it can also function as a wired controller by connecting
it directly to a PC via USB, hence the need for two USD PIDs. 0x1430 is the
dongle, and 0x1431 is the controller.

Signed-off-by: Tom Panfil <tom@steelseries.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CIFS: Fix possible hang during async MTU reads and writes

commit acc58d0bab55a50e02c25f00bd6a210ee121595f upstream.

When doing MTU i/o we need to leave some credits for
possible reopen requests and other operations happening
in parallel. Currently we leave 1 credit which is not
enough even for reopen only: we need at least 2 credits
if durable handle reconnect fails. Also there may be
other operations at the same time including compounding
ones which require 3 credits at a time each. Fix this
by leaving 8 credits which is big enough to cover most
scenarios.

Was able to reproduce this when server was configured
to give out fewer credits than usual.

The proper fix would be to reconnect a file handle first
and then obtain credits for an MTU request but this leads
to bigger code changes and should happen in other patches.

Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty/n_hdlc: fix __might_sleep warning

commit fc01d8c61ce02c034e67378cd3e645734bc18c8c upstream.

Fix __might_sleep warning[1] in tty/n_hdlc.c read due to copy_to_user
call while current is TASK_INTERRUPTIBLE.  This is a false positive
since the code path does not depend on current state remaining
TASK_INTERRUPTIBLE.  The loop breaks out and sets TASK_RUNNING after
calling copy_to_user.

This patch supresses the warning by setting TASK_RUNNING before calling
copy_to_user.

[1] https://syzkaller.appspot.com/bug?id=17d5de7f1fcab794cb8c40032f893f52de899324

Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Reported-by: syzbot <syzbot+c244af085a0159d22879@syzkaller.appspotmail.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uart: Fix crash in uart_write and uart_put_char

commit aff9cf5955185d1f183227e46c5f8673fa483813 upstream.

We were experiencing a crash similar to the one reported as part of
commit:a5ba1d95e46e ("uart: fix race between uart_put_char() and
uart_shutdown()") in our testbed as well. We continue to observe the same
crash after integrating the commit a5ba1d95e46e ("uart: fix race between
uart_put_char() and uart_shutdown()")

On reviewing the change, the port lock should be taken prior to checking for
if (!circ->buf) in fn. __uart_put_char and other fns. that update the buffer
uart_state->xmit.

Traceback:

[11/27/2018 06:24:32.4870] Unable to handle kernel NULL pointer dereference
                           at virtual address 0000003b

[11/27/2018 06:24:32.4950] PC is at memcpy+0x48/0x180
[11/27/2018 06:24:32.4950] LR is at uart_write+0x74/0x120
[11/27/2018 06:24:32.4950] pc : [<ffffffc0002e6808>]
                           lr : [<ffffffc0003747cc>] pstate: 000001c5
[11/27/2018 06:24:32.4950] sp : ffffffc076433d30
[11/27/2018 06:24:32.4950] x29: ffffffc076433d30 x28: 0000000000000140
[11/27/2018 06:24:32.4950] x27: ffffffc0009b9d5e x26: ffffffc07ce36580
[11/27/2018 06:24:32.4950] x25: 0000000000000000 x24: 0000000000000140
[11/27/2018 06:24:32.4950] x23: ffffffc000891200 x22: ffffffc01fc34000
[11/27/2018 06:24:32.4950] x21: 0000000000000fff x20: 0000000000000076
[11/27/2018 06:24:32.4950] x19: 0000000000000076 x18: 0000000000000000
[11/27/2018 06:24:32.4950] x17: 000000000047cf08 x16: ffffffc000099e68
[11/27/2018 06:24:32.4950] x15: 0000000000000018 x14: 776d726966205948
[11/27/2018 06:24:32.4950] x13: 50203a6c6974755f x12: 74647075205d3333
[11/27/2018 06:24:32.4950] x11: 3a35323a36203831 x10: 30322f37322f3131
[11/27/2018 06:24:32.4950] x9 : 5b205d303638342e x8 : 746164206f742070
[11/27/2018 06:24:32.4950] x7 : 7520736920657261 x6 : 000000000000003b
[11/27/2018 06:24:32.4950] x5 : 000000000000817a x4 : 0000000000000008
[11/27/2018 06:24:32.4950] x3 : 2f37322f31312a5b x2 : 000000000000006e
[11/27/2018 06:24:32.4950] x1 : ffffffc0009b9cf0 x0 : 000000000000003b

[11/27/2018 06:24:32.4950] CPU2: stopping
[11/27/2018 06:24:32.4950] CPU: 2 PID: 0 Comm: swapper/2 Tainted: P      D    O    4.1.51 #3
[11/27/2018 06:24:32.4950] Hardware name: Broadcom-v8A (DT)
[11/27/2018 06:24:32.4950] Call trace:
[11/27/2018 06:24:32.4950] [<ffffffc0000883b8>] dump_backtrace+0x0/0x150
[11/27/2018 06:24:32.4950] [<ffffffc00008851c>] show_stack+0x14/0x20
[11/27/2018 06:24:32.4950] [<ffffffc0005ee810>] dump_stack+0x90/0xb0
[11/27/2018 06:24:32.4950] [<ffffffc00008e844>] handle_IPI+0x18c/0x1a0
[11/27/2018 06:24:32.4950] [<ffffffc000080c68>] gic_handle_irq+0x88/0x90

Fixes: a5ba1d95e46e ("uart: fix race between uart_put_char() and uart_shutdown()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Samir Virmani <samir@embedur.com>
Acked-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: Handle problem if line discipline does not have receive_buf

commit 27cfb3a53be46a54ec5e0bd04e51995b74c90343 upstream.

Some tty line disciplines do not have a receive buf callback, so
properly check for that before calling it.  If they do not have this
callback, just eat the character quietly, as we can't fail this call.

Reported-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: rtl8188eu: Add device code for D-Link DWA-121 rev B1

commit 5f74a8cbb38d10615ed46bc3e37d9a4c9af8045a upstream.

This device was added to the stand-alone driver on github.
Add it to the staging driver as well.

Link: https://github.com/lwfinger/rtl8188eu/commit/a0619a07cd1e
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

char/mwave: fix potential Spectre v1 vulnerability

commit 701956d4018e5d5438570e39e8bda47edd32c489 upstream.

ipcnum is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

drivers/char/mwave/mwavedd.c:299 mwave_ioctl() warn: potential spectre issue 'pDrvData->IPCs' [w] (local cap)

Fix this by sanitizing ipcnum before using it to index pDrvData->IPCs.

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>