mwifiex: update BSS parameters in dump_station_info()

This enables user to check beacon interval, DTIM period, short slot
time and short preamble information using "iw dev mlan0 link" command
when station is in connected state.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: pass priv pointer instead of adapter

Pass mwifiex_private pointer directly to wmm_add_buf_txqueue()
instead of passing adapter and then deriving priv again in
mwifiex_get_priv_by_id(). This reduces a 'for' loop in TX path.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: remove PWR_PIN_CFG=0x3 during init

This seems to be only needed as workaround for hardware problem on
PCI devices.

Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: zero MAC_SYS_CTRL bits during BBP and MAC reset

Zero all other bits than RESET_CSR and RESET_BBP when want to do the
reset, that the vendor driver behaviour.

Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800: disable DMA after firmware load

We can receive frames just after firmware load with current code, so
disable DMA just after firmware is loaded, not before.

Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2800usb: initialize H2M_INT_SRC register

Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and
never touch this register later. It is not touched at all by Ralink PCI
driver.

Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

kernel-doc: fix new warnings in cfg80211.h

Fix new kernel-doc warnings:

Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: allow users to lower output power level

This patch implements a simple way of reducing the
output power of the device by a configurable upper
limit.

Requested-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

{nl,cfg,mac}80211: Add support of setting non-forwarding entity in Mesh

A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix a few -Wshadow warnings

It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix a few -Wshadow warnings

It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: make CQM RSSI support per virtual interface

Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: make beacon filtering per virtual interface

Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco_usb: remove version definition

Avoids this:

  CC [M]  drivers/net/wireless/orinoco/orinoco_usb.o
drivers/net/wireless/orinoco/orinoco_usb.c:1759:13: warning: ‘version’ defined but not used

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: use bool type for no_hw_rfkill_switch module parameter

Avoids this:

  CC [M]  drivers/net/wireless/ath/ath5k/base.o
drivers/net/wireless/ath/ath5k/base.c: In function ‘__check_no_hw_rfkill_switch’:
drivers/net/wireless/ath/ath5k/base.c:85:1: warning: return from incompatible pointer type

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: claim support for IBSS RSN

Skip group keys configuration in hardware in order to make IBSS RSN work.
Keys will be managed using software.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Add NCI multiple targets support

Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: NFC core layer should not set the target_idx

The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Clearly separate NCI states from flags

Make a clear separation between NCI states and flags.
This is required in order to support more NCI states (e.g.
for multiple targets support).

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: in IBSS use the Auth frame to trigger STA reinsertion

In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.

The joining operation is recognised thank the Auth frame being received.

This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add a 2-way Authentication challenge to IBSS mode

In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Free sk_buff if nfcwilink_send fails

Free sk_buff if nfcwilink_send fails.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Download TI NFC init script

Download TI NFC init script during nfcwilink open operation,
after the NFC channel is registered with TI shared transport.
TI NFC init script is written in BTS format.
First, read the chip version via a special vendor specific command.
Second, we request the relevant BTS file from the user space, and
then send the BTS commands to the chip.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Add endian annotations to nfcwilink driver

Add endian annotations to TI nfcwilink driver.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Add NCI data exchange timer

Add NCI data exchange timer to catch timeouts,
and call the data exchange callback with an error.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up rate control code

It seems exceedingly unlikely that we'll ever
support swapping rate control algorithms at
runtime, so remove the unused refcounting code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up aggregation destruction

Yogesh's patch to destroy aggregation sessions when
stations are destroyed was needed, but unnecessarily
complex. Clean up this code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Export new attributes sensb_res and sensf_res

Export new attributes sensb_res for tech B and sensf_res
for tech F in the target info (returned as a response to
NFC_CMD_GET_TARGET).
The max size of the attributes nfcid1, sensb_res and sensf_res
is exported to user space though include/linux/nfc.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Trivial typo of "couldn" to "could" fix

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: Use pr_fmt and pr_<level>

Convert printks to pr_<level>
Prefix logging with pr_fmt.
Use ##__VA_ARGS__ in some WL_ logging macros.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: Use brcmu_dbg_hex_dump

Convert a couple of pr_debug/print_hex_dump to
the standard utility.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: Convert printk(KERN_DEBUG to pr_debug

Use pr_debug to allow dynamic debugging to work.

Move an #endif to allow brcmf_dbg_hex_dump
to be outside the #if/#endif block.
Move a const char* declaration to be inside a
pr_debug so the function doesn't need a #if/#endif
block.
Don't use temporaries in debugging functions so
the code can be optimized away.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Remove useless #ifdef DEBUG

This doesn't do anything anymore.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: Add and use brcmX_dbg_dump_hex

Reduce the number of #ifdef DEBUG uses by
adding a dbg_hex_dump routine which has the
appropriate #ifdef DEBUG test.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: Convert printk(KERN_DEBUG to pr_debug

Allow dynamic debugging.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: Use normal DEBUG define

Current CONFIG_BRCMDBG flag when enabled does not
necessarily enable proper pr_debug output when
DEBUG is not also enabled.

Remove BCMDBG define and just use DEBUG instead.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: claim support for IBSS RSN

Disable group keys programming when using IBSS RSN. Keys will be managed using
software. In this way IBSS RSN can correctly work.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: remove eeprom data injection option

In the early days, this was a quite useful software
feature for testing different regdomains and chain
configurations without adding debugfs cruft into
the driver. Nowadays, the driver's phy code seems
to be stable and there's no need for it anymore.
Therefore I decided to removed altogether.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove useless DA checking in ieee80211_rx_mgmt_probe_resp()

Actually the DA field has already been checked along the rx path (in
prepare_for_handlers()) and this check is therefore useless at this point.

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: derive priv from net_device instead of wiphy

Currently mwifiex_private pointers are derived from wiphy
structures. This will always work as long as there is only
one net_device associated with one wiphy. In scenarios where
there are multiple net_devices associated with single
wiphy, one should use net_device to derive the priv.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: use bss_type and bss_num to retrieve priv

Current implementation, for retrieving priv from adapter,
uses bss_index. In multi interface environment supporting
different types, bss_index may not be unique.

Use bss_type along with bss_num to retrieve the priv.
bss_index is removed with this change.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: Enable logging of SPROM offset

The SPROM location has been relocated again for some devices. This patch
will log the offset when CONFIG_BCMA_DEBUG has been selected.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix the maximum transmit power with power constraint

The local maximum transmit power for a channel is defined as the maximum
regulatory transmission power minus the local power constraint specified
for the channel in the Power Constraint element. (7.3.2.15 IEEE80211 2007)

Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: Save original maximum regulatory transmission power for the calucation of the local maximum transmit power

The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.

The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).

The transmit power from a wireless device should not greater than the
local maximum transmit power.

The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.

Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: claim to support IBSS RSN.

On carl9170, HW encryption is disabled on IBSS; the mac80211
software-based encryption is used instead. As mac80211 supports IBSS
RSN (per-STA GTK), claim its support in the carl9170 PHY.

Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: In IBSS the DA field of auth frames is different from BSSID

In case of authentication frame exchange between two IBSS STAs, the
DA field must contain the destinatioin address (instead of the BSSID).

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: refactor __ieee80211_get_channel_mode

Use a switch statement instead of a list of if
statements. Also include AP_VLAN in the list
and skip them since the AP interface will also
be looked at.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/mwifiex/scan.c: convert GFP_KERNEL to GFP_ATOMIC

The function is called with locks held and thus should not use GFP_KERNEL.

The semantic patch that makes this report is available
in scripts/coccinelle/locks/call_kern.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/

Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Increase NCI deactivate timeout

Increase NCI deactivate timeout from 5 sec to 30 sec.
NCI deactivate procedure might take a long time,
depending on the local and remote parameters.

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Complete NCI deactivate in deactivate_ntf

If a target was active, complete the NCI deactivate request
only in deactivate_ntf. Otherwise, complete it at deactivate_rsp.
Deactivate_ntf represents the actual disconnection event (sent from
the NCI controller).

Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192se: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192de: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192cu: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192ce: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192c_common: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Update copyright dates

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192cu: Remove dead code never selected

The original driver contained some conditional code that was not selected,
but was not deleted in case it would be used later. That code can now be
removed.

Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c_common: rtl8192de: Check for allocation failures

In https://bugzilla.redhat.com/show_bug.cgi?id=771656, a kernel bug was
triggered due to a failed skb allocation that was not checked. This event
lead to an audit of all memory allocations in the complete rtlwifi family
of drivers. This patch fixes the rest.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: minor cleanup

we would have bailed out if 'ifibss->fixed_channel'
is valid i.e. we had used 'fixed-freq' parameter in iw ibss
join command. this is with the state 'IEEE80211_IBSS_MLME_JOINED'
so no need to check for it

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update Copyright

Update Copyright to 2012

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add testmode cmd IWL_TM_CMD_APP2DEV_GET_FW_INFO

Add new testmode command IWL_TM_CMD_APP2DEV_GET_FW_INFO for
reporting the following information of existing loaded uCode image.
+ uCode type
+ Instruction section size
+ Data section size

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update error dump in testmode command sram_read

The error message will be show up by using IWL_ERR
insteads of IWl_DEBUG_INFO.

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: enhance testmode command sram_read

This patch enables SRAM read function to support entire target memory.

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update testmode command of direct register access

In order to make sure the testcommand function of direct register
access can be performed even NIC is asleep, replace corresponding
handler iwl_read32 and iwl_write32 by using iwl_direct_read32 and
iwl_direct_write32.

Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Sanity check for sta_id

On my testing, I saw some strange behavior

[  421.739708] iwlwifi 0000:01:00.0: ACTIVATE a non DRIVER active station id 148 addr 00:00:00:00:00:00
[  421.739719] iwlwifi 0000:01:00.0: iwl_sta_ucode_activate Added STA id 148 addr 00:00:00:00:00:00 to uCode

not sure how it happen, but adding the sanity check to prevent memory
corruption

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: don't process the info from uCode if does not has ownership

When enable the testmode from user space and working with uCode, driver does
not own the uCode and should not process the notifications or pkts from uCode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Simplify chip version id logging

Reduce object size a few KB too.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 584493   55333  126800  766626   bb2a2 drivers/net/wireless/rtlwifi/built-in.o.new
 586904   55333  127216  769453   bbdad drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove incorrect logging message prefixes

pr_fmt() adds them.  These are unnecessary and wrong.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: add CONFIG_RTLWIFI_DEBUG to remove all of the debug logging code

It does seem odd though to have a DBG_EMERG and not always
emit it.

What might also be useful for any embedded use is to add
CONFIG_RTLWIFI_DEBUG to conditionally remove all of the
debug logging code to reduce the largish object size.

This reduces the object size by about 1/3 (250KB)
when CONFIG_RTLWIFI_DEBUG is not set.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 368722   55333   94224  518279   7e887 drivers/net/wireless/rtlwifi/built-in.o.new
 586904   55333  127216  769453   bbdad drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Optimize RT_TRACE macro use of KBUILD_MODNAME for size

Moving the KBUILD_MODNAME to the format reduces the
overall object size a small amount.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 586904   55333  127216  769453   bbdad drivers/net/wireless/rtlwifi/built-in.o.new
 588901   55333  127216  771450   bc57a drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Remove duplicate __func__

The RT_TRACE macro already prepends it.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Convert RT_ASSERT macro to use ##__VA_ARGS__

Consolidate printks to avoid possible message interleaving
and reduce the object size.

Remove unnecessary RT_ASSERT parentheses.
Align arguments.
Coalesce formats.
Remove unnecessary __func__ use as the macro uses it.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 588901   55333  127216  771450   bc57a drivers/net/wireless/rtlwifi/built-in.o.new
 590002   55333  127560  772895   bcb1f drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Convert RTPRINT macro to use ##__VA_ARGS__

Consolidate printks to avoid possible message interleaving
and reduce the object size.

Remove unnecessary RTPRINT parentheses.
Coalesce formats.
Align arguments.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 590002   55333  127560  772895   bcb1f drivers/net/wireless/rtlwifi/built-in.o.new
 594841   55333  129680  779854   be64e drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Convert RT_TRACE macro to use ##__VA_ARGS__

Consolidate printks to avoid possible message interleaving
and reduce the object size.

Remove unnecessary RT_TRACE parentheses.

Miscellaneous typo and grammar fixes.
Add missing newlines to formats.
Remove duplicate KERN_DEBUG prefixes.
Coalesce formats.
Align arguments.

$ size drivers/net/wireless/rtlwifi/built-in.o*
   text    data     bss     dec     hex filename
 594841   55333  129680  779854   be64e drivers/net/wireless/rtlwifi/built-in.o.new
 607022   55333  138720  801075   c3933 drivers/net/wireless/rtlwifi/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Standardize RT_PRINT_DATA macro and uses

Use a single printk(KERN_DEBUG to emit the header line
to avoid any possible output interleaving.

Remove unnecessary parentheses from the calling uses.
Standardize header arg without trailing \n or colon.
Fix a few pairwiase/pairwise typos.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Neaten RT_ASSERT, RT_TRACE, RTPRINT, RT_PRINT_DATA macros

Make the macros a bit more readable.

Use do {...} while (0) without terminating semicolons.
Add missing terminating semicolon to a few uses.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: trivial: change save&rest order in RSSI polling

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: implement RSSI calibration for rev3+

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: make ethtool_ops const

All usage of ethtool_ops should be const; also add comma at end
of initializer list.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: upload PAPD PGA gain delta table

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: fix typos in RF control

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: add helper for getting gain table

Also move the code to tables file.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: implement TX power control setup

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: add maskset helpers

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: SPROM: extract power info for cores

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: SPROM: add macro for easier extraction

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: SPROM: extract each core power info

We already extract some basic info but it's incomplete, reads info
about the first core only. Used data structure doesn't allow easy
adding of more cores.
This patch adds new struct and array for storing power info. The plan
is to: switch all extractors (including the ones using NVRAM) to new
struct, switch drivers, then deprecate and finally drop old SSB fields.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: check sta_apply_parameters() return value

Bail out if sta_apply_parameters() returns an error.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

tg3: Fix single-vector MSI-X code

Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled.  However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup.  When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.

This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt.  In such a configuration, the
device's multivector interrupt mode must be disabled.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

openvswitch: Fix multipart datapath dumps.

The logic to split up the list of datapaths into multiple Netlink messages
was simply wrong, causing the list to be terminated after the first part.
Only about the first 50 datapaths would be dumped.  This fixes the
problem.

Reported-by: Paul Ingram <paul@nicira.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6: fix per device IP snmp counters

In commit 4ce3c183fca (snmp: 64bit ipstats_mib for all arches), I forgot
to change the /proc/net/dev_snmp6/xxx output for IP counters.

percpu array is 64bit per counter but the folding still used the 'long'
variant, and output garbage on 32bit arches.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inetpeer: initialize ->redirect_genid in inet_getpeer()

kmemcheck complains that ->redirect_genid doesn't get initialized.
Presumably it should be set to zero.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix NULL-deref in WARN() in skb_gso_segment()

Bug was introduced in commit c8f44affb7244f2ac3e703cab13d55ede27621bb.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: WARN if skb_checksum_help() is called on skb requiring segmentation

skb_checksum_help() has never done anything useful with skbs that
require segmentation.  Setting skb->ip_summed = CHECKSUM_NONE makes
them invalid and provokes a later WARNing in skb_gso_segment().

Passing such an skb to skb_checksum_help() indicates a bug, so we
should warn about it immediately.  Move the warning from
skb_gso_segment() into a shared function, and add gso_type and
gso_size to it.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

caif: Remove bad WARN_ON in caif_dev

Remove WARN_ON and bad handling of SKB without destructor callback
in caif_flow_cb. SKB without destructor cannot be handled as an
error case.

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

caif: Fix typo in Vendor/Product-ID for CAIF modems

Fix typo for the Vendor/Product Id for ST-Ericsson CAIF modems.
Discovery is based on fixed USB vendor 0x04cc (ST-Ericsson),
product-id 0x230f (NCM).

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Disable AN KR work-around for BCM57810

Disable the work-around for the autoneg KR of the BCM57810 in case the Warpcore version is 0xD108 and above, which fixes this problem.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Remove AutoGrEEEn for BCM84833

Disable the autoGrEEEn feature for BCM84833.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnx2x: Remove 100Mb force speed for BCM84833

Remove unsupported speed of 100Mb force for BCM84833 due to hardware
limitation.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>