Phil Elwell [Thu, 6 Feb 2020 12:23:15 +0000 (12:23 +0000)]
of: overlay: Correct symbol path fixups
When symbols from overlays are added to the live tree their paths must
be rebased. The translated symbol is normally the result of joining
the fragment-relative path (with a leading "/") to the target path
(either copied directly from the "target-path" property or resolved
from the phandle). This translation fails when the target is the root
node (a common case for Raspberry Pi overlays) because the resulting
path starts with a double slash. For example, if target-path is "/" and
the fragment adds a node called "newnode", the label associated with
that node will be assigned the path "//newnode", which can't be found
in the tree.
Fix the failure case by explicitly replacing a target path of "/" with
an empty string.
Fixes:
d1651b03c2df ("of: overlay: add overlay symbols to live device tree")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 2 Mar 2020 14:42:23 +0000 (14:42 +0000)]
video: fbdev: bcm2708_fb: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 6 Jan 2020 16:04:30 +0000 (16:04 +0000)]
pinctrl: bcm2835: Remove gpiochip on error
A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix
the leak with the use of devm_gpiochip_add_data.
Fixes:
85ae9e512f43 ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 3 Feb 2020 17:30:46 +0000 (17:30 +0000)]
staging: vchiq_arm: Give vchiq children DT nodes
vchiq kernel clients are now instantiated as platform drivers rather
than using DT, but the children of the vchiq interface may still
benefit from access to DT properties. Give them the option of a
a sub-node of the vchiq parent for configuration and to allow
them to be disabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Luke Hinds [Wed, 22 Jan 2020 16:03:00 +0000 (16:03 +0000)]
Initialise rpi-firmware before clk-bcm2835
The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted
Platform Module) having been registered when it initialises; otherwise
it assumes there is no TPM. It has been observed on BCM2835 that IMA
is initialised before TPM, and that initialising the BCM2835 clock
driver before the firmware driver has the effect of reversing this
order.
Change the firmware driver to initialise at core_initcall, delaying the
BCM2835 clock driver to postcore_initcall.
See: https://github.com/raspberrypi/linux/issues/3291
https://github.com/raspberrypi/linux/pull/3297
Signed-off-by: Luke Hinds <lhinds@redhat.com>
Co-authored-by: Phil Elwell <phil@raspberrypi.org>
Stefan Wahren [Fri, 27 Dec 2019 10:40:56 +0000 (11:40 +0100)]
ARM: bcm: Backport BCM2711 support from upstream
Make the BCM2711 a different machine, but keep it in board_bcm2835.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Dave Stevenson [Tue, 18 Jun 2019 11:15:50 +0000 (12:15 +0100)]
staging: vchiq: Use the old dma controller for OF config on platform devices
vchiq on Pi4 is no longer under the soc node, therefore it
doesn't get the dma-ranges for the VPU.
Switch to using the configuration of the old dma controller as
that will set the dma-ranges correctly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Tue, 29 Jan 2019 16:13:25 +0000 (16:13 +0000)]
staging: vchiq_arm: Set up dma ranges on child devices
The VCHIQ driver now loads the audio, camera, codec, and vc-sm
drivers as platform drivers. However they were not being given
the correct DMA configuration.
Call of_dma_configure with the parent (VCHIQ) parameters to be
inherited by the child.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
popcornmix [Mon, 9 Sep 2019 14:49:56 +0000 (15:49 +0100)]
clk-raspberrypi: Allow cpufreq driver to also adjust gpu clocks
For performance/power it is beneficial to adjust gpu clocks with arm clock.
This is how the downstream cpufreq driver works
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Thu, 5 Sep 2019 16:59:14 +0000 (17:59 +0100)]
v3d_gem: Kick the clock so firmware knows we are using firmware clock interface
Setting the v3d clock to low value allows firmware to handle dvfs in case
where v3d hardware is not being actively used (e.g. console use).
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Fri, 23 Aug 2019 15:34:38 +0000 (16:34 +0100)]
v3d_drv: Handle missing clock more gracefully
Signed-off-by: popcornmix <popcornmix@gmail.com>
James Hughes [Thu, 31 Oct 2019 14:39:44 +0000 (14:39 +0000)]
net:phy:2711 Allow ethernet LED mode to be set via device tree
Add device tree entries and code to allow the specification of
the lighting modes for the LED's on the ethernet connector.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
net:phy:2711 Change the default ethernet LED actions
This should return default behaviour back to that of previous
releases.
Dave Stevenson [Wed, 6 Nov 2019 13:57:58 +0000 (13:57 +0000)]
staging: vchiq_arm: Register bcm2835-codec as a platform driver
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the V4L2 codec driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 6 Nov 2019 13:57:48 +0000 (13:57 +0000)]
staging: vchiq_arm: Register vcsm-cma as a platform driver
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the vcsm-cma driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Mon, 11 Nov 2019 20:18:08 +0000 (20:18 +0000)]
drm/v3d: Suppress all but the first MMU error
The v3d driver currently encounters a lot of MMU PTE exceptions, so
only log the first to avoid swamping the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Markus Proeller [Thu, 10 Oct 2019 17:12:36 +0000 (19:12 +0200)]
media: i2c: Add a driver for the Infineon IRS1125 depth sensor
The Infineon IRS1125 is a time of flight depth sensor that
has a CSI-2 interface.
Add a V4L2 subdevice driver for this device.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Thu, 10 Oct 2019 17:12:08 +0000 (19:12 +0200)]
dt-bindings: Add binding for the Infineon IRS1125 sensor
Adds a binding for the Infineon IRS1125 time-of-flight depth
sensor.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Stefan Wahren [Thu, 19 Sep 2019 18:45:30 +0000 (20:45 +0200)]
ARM: bcm: Switch board, clk and pinctrl to bcm2711 compatible
After the decision to use bcm2711 compatible for upstream, we should
switch all accepted compatibles to bcm2711. So we can boot with
one DTB the down- and the upstream kernel.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Dave Stevenson [Mon, 8 Feb 2021 11:48:35 +0000 (11:48 +0000)]
staging:bcm2835-camera: Fix the cherry-pick of AWB Greyworld
The cherry-pick of the patch that added the greyworld AWB mode
was incomplete. Fix it up.
Fixes:
b3ef481fe243 "staging: bcm2835-camera: Add greyworld AWB mode"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
John Cox [Fri, 6 Aug 2021 13:32:44 +0000 (14:32 +0100)]
media: v4l2: Add Greyworld AWB control name
Add name for greyworld to white_balance preset names.
This patch previously applied to v4l2-ctrl.c but that was split
and deleted.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Dave Stevenson [Fri, 6 Sep 2019 14:13:06 +0000 (15:13 +0100)]
staging: bcm2835-camera: Add greyworld AWB mode
This is mainly used for the NoIR camera which has no IR
filter and can completely confuse normal AWB presets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Fri, 6 Sep 2019 14:04:51 +0000 (15:04 +0100)]
v4l2: Add a Greyworld AWB mode.
Adds a simple greyworld white balance preset, mainly for use
with cameras without an IR filter (eg Raspberry Pi NoIR)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
David Plowman [Tue, 29 Jun 2021 13:38:23 +0000 (14:38 +0100)]
Documentation: devicetree: Add documentation for imx378 sensor
The imx378 sensor is compatible with the imx477 and shares common
device tree settings.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Lee Jackson [Fri, 27 Aug 2021 06:36:55 +0000 (14:36 +0800)]
media: i2c: imx519: Support for the Sony IMX519 sensor
dt-bindings: media: i2c: Add IMX519 CMOS sensor binding
Add YAML device tree binding for IMX519 CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: Add driver for IMX519 sensor
Adds a driver for the 16MPix IMX519 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4656x3496 10-bit @ 10fps
3840x2160 10-bit (cropped) @ 21fps
2328x1748 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Advertise embedded data node on media pad 1
This commit updates the imx519 driver to adverise support for embedded
data streams.
The imx519 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: Update imx519 Kconfig entry
Bring the IMX519 Kconfig declaration in line with the upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Naushir Patuck [Thu, 7 May 2020 14:50:54 +0000 (15:50 +0100)]
media: i2c: imx477: Support for the Sony IMX477 sensor
dt-bindings: media: i2c: Add IMX477 CMOS sensor binding
Add YAML device tree binding for IMX477 CMOS image sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: Add driver for Sony IMX477 sensor
Adds a driver for the 12MPix Sony IMX477 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4056x3040 12-bit @ 10fps
2028x1520 12-bit (binned) @ 40fps
2028x1050 12-bit (cropped/binned) @ 50fps
1012x760 10-bit (scaled) @ 120 fps
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add support for adaptive frame control
Use V4L2_CID_EXPOSURE_AUTO_PRIORITY to control if the driver should
automatically adjust the sensor frame length based on exposure time,
allowing variable frame rates and longer exposures.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Return correct result on sensor id verification
The test should return -EIO if the register read id does not match
the expected sensor id.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Parse and register properties
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
media: i2c: imx477: Selection compliance fixes
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx477 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
This commit mirrors
543790f777ba1b3264c168c653db6d415e7c983f done for
the imx219 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove auto frame length adjusting
The V4L2_CID_EXPOSURE_AUTO_PRIORITY was used to let the sensor control
frame length (effectively framerate) based on the requested exposure
time requested. Remove this feature as it is never used, and goes
against how V4L2 likes to handle exposure and vblank controls.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add very long exposure control to the driver
Add support for very long exposures by using the exposure multiplier
register. Userland does not need to pass any additional controls to
enable long exposures, it simply requests a larger vblank to extend the
exposure control range appropriately.
Currently, since hblank is fixed, a maximum of approximately 124 seconds
of exposure time can be used. In a future change, hblank could also be
controlled in userland to give over 200 seconds of exposure time.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix crop height for 2028x1080 mode
The crop height for this mode was set at 2600 lines, it should be 2160
lines instead.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Replace existing 1012x760 mode
The existing 1012x760 120 fps mode has significant IQ problem using
the internal sensor scaler. Replace this mode with a 1332x990 120 fps
mode instead. This new mode has a smaller field of view, but does not
suffer from the bad IQ of the original mode.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove internal v4l2_mbus_framefmt from the state
The only field in this struct that is used is the format code, so
replace the struct with this single field.
Save the format code in imx477_set_pad_format() when setting up a new
mode so that imx477_get_pad_format() performs the right lookup.
Otherwise, this caused a bug where the mode lookup occurred on the
12-bit table rather than the 10-bit table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove unused function parameter
The struct imx477 *ctrl parameter is not used in the function
imx477_adjust_exposure_range(), so remove it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix for long exposure limit calculations
Do not scale IMX477_EXPOSURE_OFFSET with the long exposure factor during
the limit calculations. This allows larger exposure times, and does seem to be
what the sensor is doing internally.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Extend driver to support imx378 sensor
The imx378 sensor is almost identical to the imx477 and can be
supported as a "compatible" sensor with just a few extra register
writes.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Fix framerates for 1332x990 mode
The imx477 driver's line length for this mode had not been updated to
the value supplied to us by the sensor manufacturer. With this
correction the sensor delivers the framerates that are expected.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow control of on-sensor DPC
A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.
This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Add vsync trigger_mode parameter
trigger_mode == 0 (default) => no effect / no registers written
trigger_mode == 1 => source
trigger_mode == 2 => sink
This can be set e.g. in /boot/cmdline.txt as imx477.trigger_mode=N
Signed-off-by: Jonas Jacob <jonas.jacob@neocortexvision.com>
media: i2c: Update imx477 Kconfig entry
Bring the IMX477 Kconfig declaration in line with upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: imx477: Correct minimum exposure lines
The minimum number of exposure lines value (IMX477_EXPOSURE_MIN) was
previously 20 but this is not correct. The datasheet is not completely
explicit, however the new value of 4 has been tested with all the
sensor modes supported by this driver, and matches the lowest exposure
value of 114us that could be achieved wtih Raspberry Pi's legacy
firmware driver.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow dynamic horizontal blanking control
Currently, the V4L2_CID_HBLANK control is marked as read-only. Remove this
restriction and allow userland to modify the control if needed.
Set the maximum limit of the line length to 0xfff0.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Reset hblank on mode switch
Reset the hblank control to the minimum value on every mode switch. This is to
account for userland instances that do not yet control hblank, otherwise it
gets set to a non-optimal value.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Do not unconditionally adjust hblank and vblank limits
On a mode change, only call imx477_set_framing_limits() to adjust the hblank
and vblank limits if the new mode is different from the existing mode. This
preserves any manual control values the user might have set.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Phil Elwell [Tue, 3 Sep 2019 17:17:25 +0000 (18:17 +0100)]
arch/arm64: Add Revision, Serial, Model to cpuinfo
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 3 Sep 2019 17:16:56 +0000 (18:16 +0100)]
arch/arm: Add model string to cpuinfo
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 9 Aug 2019 07:51:43 +0000 (08:51 +0100)]
net: bcmgenet: Workaround #2 for Pi4 Ethernet fail
Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Thu, 1 Aug 2019 15:41:20 +0000 (16:41 +0100)]
hid: usb: Add device quirks for Freeway Airmouse T3 and MX3
These wireless mouse/keyboard combo remote control devices specify
multiple "wheel" events in their report descriptors. The wheel events
are incorrectly defined and apparently map to accelerometer data, leading
to spurious mouse scroll events being generated at an extreme rate when
the device is moved.
As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask
feeding the extra wheel events to the input subsystem.
See: https://github.com/raspberrypi/firmware/issues/1189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Thu, 9 May 2019 13:30:37 +0000 (14:30 +0100)]
drivers: char: add chardev for mmap'ing the RPiVid control registers
Based on the gpiomem driver, allow mapping of the decoder register
spaces such that userspace can access control/status registers.
This driver is intended for use with a custom ffmpeg backend accelerator
prior to a v4l2 driver being written.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
driver: char: rpivid: Destroy the legacy device on remove
The legacy name support created a new device that was never destroyed.
If the driver was unloaded and reloaded, it failed due to the
device already existing.
Fixes: "75f1d14 driver: char: rpivid - also support legacy name"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Clean up error handling use of ERR_PTR/IS_ERR
The driver used an unnecessary intermediate void* variable so it
only called ERR_PTR once to convert to the error value.
Switch to converting as the error arises to remove these intermediate
variables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Add error handling to the legacy device load
The return value from device_create for the legacy device was never
checked or handled. Add the required error handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix coding style whitespace issues.
Makes checkpatch happier.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpimem: Add SPDX licence header.
Stops checkpatch complaining.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix access to freed memory
The error path during probe frees the private memory block, and
then promptly dereferences it to log an error message.
Use the base device instead of the pointer to it in the private
structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Remove legacy name support
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
driver: char: rpivid: Don't map more than wanted
Limit mappings to the permitted range, but don't map more than asked
for otherwise we walk off the end of the allocated VMA.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Eric Anholt [Thu, 2 May 2019 20:22:53 +0000 (13:22 -0700)]
drm/v3d: Clock V3D down when not in use.
My various attempts at re-enabling runtime PM have failed, so just
crank the clock down when V3D is idle to reduce power consumption.
Signed-off-by: Eric Anholt <eric@anholt.net>
drm/v3d: Plug dma_fence leak
The irq_fence and done_fence are given a reference that is never
released. The necessary dma_fence_put()s seem to have been
deleted in error in an earlier commit.
Fixes:
0b73676836b2 ("drm/v3d: Clock V3D down when not in use.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 12 Jul 2019 14:38:35 +0000 (15:38 +0100)]
i2c: bcm2835: Set clock-stretch timeout to 35ms
The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 11 Jun 2019 16:38:28 +0000 (17:38 +0100)]
arm: bcm2835: Add bcm2838 compatible string.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Tue, 11 Jun 2019 10:42:03 +0000 (11:42 +0100)]
usbhid: call usb_fixup_endpoint after mangling intervals
Lets the mousepoll override mechanism work with xhci.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Fri, 10 Mar 2023 14:21:42 +0000 (14:21 +0000)]
usb: xhci: drop and add the endpoint context in xhci_fixup_endpoint()
Setting both the Drop and Add bits on the input context prevents the
corruption of split transactions seen with the BCM2711 XHCI controller,
which is a dwc3 variant.
This is a downstream feature that allows usbhid to restrict polling
intervals on mice and keyboards, and was only tested on a VL805 which
didn't complain about the fact the endpoint got added twice.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Wed, 11 Aug 2021 14:33:57 +0000 (15:33 +0100)]
usb: xhci: workaround for bogus SET_DEQ_PENDING endpoint state
See https://github.com/raspberrypi/linux/issues/3981
An unknown unsafe memory access can result in the ep_state variable
in xhci_virt_ep being trampled with a stuck SET_DEQ_PENDING state
despite successful completion of a Set TR Deq Pointer command.
All URB enqueue/dequeue calls for the endpoint will fail in this state
so no transfers are possible until the device is reconnected.
As a workaround, clear the flag if we see it set and issue a new Set
TR Deq command anyway - this should be harmless, as a prior Set TR Deq
command will only have been issued in the Stopped state, and if the
endpoint is Running then the controller is required to ignore it and
respond with a Context State Error event TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Tue, 11 Jun 2019 10:33:39 +0000 (11:33 +0100)]
xhci: implement xhci_fixup_endpoint for interval adjustments
Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Tue, 11 Jun 2019 09:55:00 +0000 (10:55 +0100)]
usb: add plumbing for updating interrupt endpoint interval state
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Tue, 14 May 2019 16:17:59 +0000 (17:17 +0100)]
net: genet: enable link energy detect powerdown for external PHYs
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Phil Elwell [Wed, 27 Mar 2019 13:45:46 +0000 (13:45 +0000)]
bcmgenet: Better coalescing parameter defaults
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Wed, 12 Sep 2018 13:44:53 +0000 (14:44 +0100)]
bcmgenet: constrain max DMA burst length
Stefan Wahren [Sat, 4 May 2019 15:06:15 +0000 (17:06 +0200)]
hwrng: iproc-rng200: Add BCM2838 support
The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the
support to this driver instead of bcm2835-rng.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
hwrng: iproc-rng200: Correct SoC name
The Pi 4 SoC is called BCM2711, not BCM2838.
Fixes: "hwrng: iproc-rng200: Add BCM2838 support"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 29 May 2019 14:47:42 +0000 (15:47 +0100)]
arm: bcm2835: DMA can only address 1GB
The legacy peripherals can only address the first gigabyte of RAM, so
ensure that DMA allocations are restricted to that region.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 20 Feb 2019 08:49:39 +0000 (08:49 +0000)]
arm: bcm2835: Fix FIQ early ioremap
The ioremapping creates mappings within the vmalloc area. The
equivalent early function, create_mapping, now checks that the
requested explicit virtual address is between VMALLOC_START and
VMALLOC_END. As there is no reason to have any correlation between
the physical and virtual addresses, put the required mappings at
VMALLOC_START and above.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 12 Jun 2019 16:15:05 +0000 (17:15 +0100)]
w1: w1-gpio: Make GPIO an output for strong pullup
The logic to drive the data line high to implement a strong pullup
assumed that the pin was already an output - setting a value does
not change an input.
See: https://github.com/raspberrypi/firmware/issues/1143
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Thu, 2 May 2019 14:50:01 +0000 (15:50 +0100)]
staging: mmal-vchiq: Fix memory leak in error path
On error, vchiq_mmal_component_init could leave the
event context allocated for ports.
Clean them up in the error path.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 1 May 2019 12:27:23 +0000 (13:27 +0100)]
staging: mmal-vchiq: Free the event context for control ports
vchiq_mmal_component_init calls init_event_context for the
control port, but vchiq_mmal_component_finalise didn't free
it, causing a memory leak..
Add the free call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 18 Feb 2019 15:52:29 +0000 (15:52 +0000)]
staging: mmal-vchiq: Update mmal_parameters.h with recently defined params
mmal_parameters.h hasn't been updated to reflect additions made
over the last few years. Update it to reflect the currently
supported parameters.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 13 Feb 2019 12:33:29 +0000 (12:33 +0000)]
staging: mmal_vchiq: Add in the Bayer encoding formats
The list of formats was copied before Bayer support was added.
The ISP supports Bayer and is being supported by the bcm2835_codec
driver, so add in the encodings for them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Tue, 22 Jan 2019 12:04:09 +0000 (12:04 +0000)]
staging: mmal-vchiq: Fix client_component for 64 bit kernel
The MMAL client_component field is used with the event
mechanism to allow the client to identify the component for
which the event is generated.
The field is only 32bits in size, therefore we can't use a
pointer to the component in a 64 bit kernel.
Component handles are already held in an array per VCHI
instance, so use the array index as the client_component handle
to avoid having to create a new IDR for this purpose.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 29 Oct 2018 17:57:45 +0000 (17:57 +0000)]
media: videobuf2: Allow exporting of a struct dmabuf
videobuf2 only allowed exporting a dmabuf as a file descriptor,
but there are instances where having the struct dma_buf is
useful within the kernel.
Split the current implementation into two, one step which
exports a struct dma_buf, and the second which converts that
into an fd.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 24 Sep 2018 17:26:02 +0000 (18:26 +0100)]
staging: vc04_services: Support sending data to MMAL ports
Add the ability to send data to ports. This only supports
zero copy mode as the required bulk transfer setup calls
are not done.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 24 Sep 2018 17:15:38 +0000 (18:15 +0100)]
staging: mmal-vchiq: Add support for event callbacks.
(Preparation for the codec driver).
The codec uses the event mechanism to report things such as
resolution changes. It is signalled by the cmd field of the buffer
being non-zero.
Add support for passing this information out to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 29 Oct 2018 16:20:46 +0000 (16:20 +0000)]
staging: mmal-vchiq: Avoid use of bool in structures
Fixes up a checkpatch error "Avoid using bool structure members
because of possible alignment issues".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Thu, 22 Nov 2018 17:31:06 +0000 (17:31 +0000)]
media: tc358743: Return an appropriate colorspace from tc358743_set_fmt
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on what was read back from the chip. When you set the format,
then the driver would choose and program the colorspace based
on the format code.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told sRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed into the chip is determined by this driver,
therefore there is no need to read back the value. Return the
colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:59:40 +0000 (14:59 +0000)]
MAINTAINERS: Add entry for BCM2835 Unicam driver
Adds entry for the new BCM2835 Unicam (CSI-2 receiver) driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:59:06 +0000 (14:59 +0000)]
dt-bindings: Document BCM283x CSI2/CCP2 receiver
Document the DT bindings for the CSI2/CCP2 receiver peripheral
(known as Unicam) on BCM283x SoCs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Rob Herring <robh@kernel.org>
Dave Stevenson [Wed, 31 Oct 2018 14:58:08 +0000 (14:58 +0000)]
media: videodev2: Add helper defines for printing FOURCCs
New helper defines that allow printing of a FOURCC using
printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc));
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:56 +0000 (14:57 +0000)]
media: adv7180: Add YPrPb support for ADV7282M
The ADV7282M can support YPbPr on AIN1-3, but this was
not selectable from the driver. Add it to the list of
supported input modes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:46 +0000 (14:57 +0000)]
media: adv7180: Default to the first valid input
The hardware default is differential CVBS on AIN1 & 2, which
isn't very useful.
Select the first input that is defined as valid for the
chip variant (typically CVBS_AIN1).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:34 +0000 (14:57 +0000)]
media: tc358743: Check I2C succeeded during probe.
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:57:21 +0000 (14:57 +0000)]
media: tc358743: Add support for 972Mbit/s link freq.
Adds register setups for running the CSI lanes at 972Mbit/s,
which allows 1080P50 UYVY down 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 31 Oct 2018 14:56:59 +0000 (14:56 +0000)]
media: tc358743: Increase FIFO level to 374.
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24-30 UYVY over 2 lanes @ 972Mbit/s, but
>374 means that the FIFO underflows on 1080P50 UYVY over 2 lanes
@ 972Mbit/s.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Tue, 5 Mar 2019 09:51:22 +0000 (09:51 +0000)]
lan78xx: EEE support is now a PHY property
Now that EEE support is a property of the PHY, use the PHY's DT node
when querying the EEE-related properties.
See: https://github.com/raspberrypi/linux/issues/2882
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Joshua Emele [Thu, 8 Nov 2018 00:07:40 +0000 (16:07 -0800)]
lan78xx: Debounce link events to minimize poll storm
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
Dave Stevenson [Thu, 10 Jan 2019 17:58:06 +0000 (17:58 +0000)]
firmware: raspberrypi: Report the fw variant during probe
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Mon, 26 Nov 2018 19:46:58 +0000 (19:46 +0000)]
net: lan78xx: Support auto-downshift to 100Mb/s
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 2 Feb 2024 15:41:29 +0000 (15:41 +0000)]
serial: sc16is7xx: Don't spin if no data received
There are multiple causes of interrupts, errors being one, and only the
receipt of data warrants continued polling.
See: https://github.com/raspberrypi/linux/issues/2676
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Stefan Wahren [Sat, 13 Oct 2018 11:31:21 +0000 (13:31 +0200)]
firmware: raspberrypi: Add backward compatible get_throttled
Avoid a hard userspace ABI change by adding a compatible get_throttled
sysfs entry. Its value is now feed by the GET_THROTTLED requests of the
new hwmon driver. The first access to get_throttled will generate
a warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
popcornmix [Mon, 17 Sep 2018 16:31:18 +0000 (17:31 +0100)]
cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with MEDIA_SUBDRV_AUTOSELECT
Phil Elwell [Thu, 5 Apr 2018 13:46:11 +0000 (14:46 +0100)]
lan78xx: Move enabling of EEE into PHY init code
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 20 Jun 2018 11:20:01 +0000 (12:20 +0100)]
brcmfmac: Re-enable firmware roaming support
As of 4.18, a firmware that implements the update_connect_params
method but doesn't claim to support roaming causes an error. We
disabled firmware roaming in 4.4 [1] because it appeared to
prevent disconnects, but let's try with the current firmware to see
if things have improved.
[1] https://github.com/raspberrypi/linux/commit/
dd9188011786fb62a7960922f31e8e086fb2009b
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Wed, 13 Jun 2018 14:21:10 +0000 (15:21 +0100)]
net: lan78xx: Disable TCP Segmentation Offload (TSO)
TSO seems to be having issues when packets are dropped and the
remote end uses Selective Acknowledge (SACK) to denote that
data is missing. The missing data is never resent, so the
connection eventually stalls.
There is a module parameter of enable_tso added to allow
further debugging without forcing a rebuild of the kernel.
https://github.com/raspberrypi/linux/issues/2449
https://github.com/raspberrypi/linux/issues/2482
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Thu, 14 Jun 2018 10:21:04 +0000 (11:21 +0100)]
irqchip: irq-bcm2835: Calc. FIQ_START at boot-time
ad83c7cb2f37 ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Sat, 12 May 2018 20:35:43 +0000 (21:35 +0100)]
firmware/raspberrypi: Notify firmware of a reboot
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Nick Bulleid [Thu, 10 May 2018 20:57:02 +0000 (21:57 +0100)]
Add ability to export gpio used by gpio-poweroff
Signed-off-by: Nick Bulleid <nedbulleid@fastmail.com>
Added export feature to gpio-poweroff documentation
Signed-off-by: Nick Bulleid <nedbulleid@fastmail.com>
popcornmix [Mon, 14 Jul 2014 21:02:09 +0000 (22:02 +0100)]
hid: Reduce default mouse polling interval to 60Hz
Reduces overhead when using X
Phil Elwell [Fri, 9 Mar 2018 12:01:00 +0000 (12:01 +0000)]
lan78xx: Read initial EEE status from DT
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
hdoverobinson [Tue, 13 Mar 2018 10:58:39 +0000 (06:58 -0400)]
added capture_clear option to pps-gpio via dtoverlay (#2433)
Phil Elwell [Tue, 20 Feb 2018 10:07:27 +0000 (10:07 +0000)]
i2c-gpio: Also set bus numbers from reg property
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 11 Dec 2017 09:18:32 +0000 (09:18 +0000)]
ARM: Activate FIQs to avoid __irq_startup warnings
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 16 Jul 2018 13:40:13 +0000 (14:40 +0100)]
dwc-otg: FIQ: Fix "bad mode in data abort handler"
Create a semi-static mapping for the USB registers early in the boot
process, before additional kernel threads are started, so all threads
will have the mappings from the start. This avoids the need for
data aborts to lazily update them.
See: https://github.com/raspberrypi/linux/issues/2450
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Noralf Trønnes [Wed, 3 Jun 2015 10:26:13 +0000 (12:26 +0200)]
ARM: bcm2835: Set Serial number and Revision
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
James Hughes [Tue, 14 Nov 2017 15:13:15 +0000 (15:13 +0000)]
AXI performance monitor driver (#2222)
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
raspberrypi_axi_monitor: suppress warning
Suppress the following warning by casting the pointer to and uintptr_t
before to u32:
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Michael Zoran [Sat, 11 Feb 2017 09:18:31 +0000 (01:18 -0800)]
ARM64: Force hardware emulation of deprecated instructions.
Michael Zoran [Sun, 15 Jan 2017 05:43:57 +0000 (21:43 -0800)]
ARM64: Round-Robin dispatch IRQs between CPUs.
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
drivers: irqchip: irq-bcm2835: Concurrency fix
The commit shown in Fixes: aims to improve interrupt throughput by
getting the handlers invoked on different CPU cores. It does so (*) by
using an irq_ack hook to change the interrupt routing.
Unfortunately, the IRQ status bits must be cleared at source, which only
happens once the interrupt handler has run - there is no easy way for
one core to claim one of the IRQs before sending the remainder to the
next core on the list, so waking another core immediately results in a
race with a chance of both cores handling the same IRQ. It is probably
for this reason that the routing change is deferred to irq_ack, but that
doesn't guarantee no clashes - after irq_ack is called, control returns
to bcm2836_chained_handler_irq which proceeds to check for other pending
IRQs at a time when the next core is probably doing the same thing.
Since the whole point of the original commit is to distribute the IRQ
handling, there is no reason to attempt to handle multiple IRQs in one
interrupt callback, so the problem can be solved (or at least made much
harder to reproduce) by changing a "while" into an "if", so that each
invocation only handles one IRQ.
(*) I'm not convinced it's as effective as claimed since irq_ack is
called _after_ the interrupt handler, but the author thought it made a
difference.
See: https://github.com/raspberrypi/linux/issues/5214
https://github.com/raspberrypi/linux/pull/1794
Fixes:
fd4c9785bde8 ("ARM64: Round-Robin dispatch IRQs between CPUs.")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Thu, 17 Dec 2015 13:37:07 +0000 (13:37 +0000)]
hci_h5: Don't send conf_req when ACTIVE
Without this patch, a modem and kernel can continuously bombard each
other with conf_req and conf_rsp messages, in a demented game of tag.
Cheong2K [Fri, 26 Feb 2016 10:20:10 +0000 (18:20 +0800)]
brcm: adds support for BCM43341 wifi
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit
73345fd212980d2e28a5c6d83801c903bd773680:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Revert "brcmfmac: Disable power management"
Shortly after the release of the Pi 3B, a loss of SSH connectivity
over WiFi was traced to the power management handling, so power
management was disabled. And so it has remained ever since.
Enabling power management saves 55mA (~270mW) on a Pi 4B, so is very
much worth the minimal effort of reverting this patch, which was
squashed and rebased many times since then to the commit hash is
meaningless.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Pantelis Antoniou [Wed, 3 Dec 2014 11:23:28 +0000 (13:23 +0200)]
OF: DT-Overlay configfs interface
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de028acaa42a0f6ff18d19756f8e825c6.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
of: configfs: Use of_overlay_fdt_apply API call
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
popcornmix [Tue, 23 Feb 2016 19:56:04 +0000 (19:56 +0000)]
bcm2835-virtgpio: Virtual GPIO driver
Add a virtual GPIO driver that uses the firmware mailbox interface to
request that the VPU toggles LEDs.
gpio: bcm-virt: Fix the get() method
The get() method does not understand the on-the-wire encoding of the
remote GPIO states, thinking they are simple on/off bits when they are
really pairs of 16-bit counts. Rewrite the get() handler to return the
value last written, which will eventually match the actual GPIO state
if there are no other changes.
See: https://github.com/raspberrypi/linux/issues/4638
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
P33M [Wed, 21 Oct 2015 13:55:21 +0000 (14:55 +0100)]
rpi_display: add backlight driver and overlay
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
Florian Meier [Mon, 25 Jan 2016 15:48:59 +0000 (15:48 +0000)]
Add support for all the downstream rpi sound card drivers
ASoC: Add support for Rpi-DAC
ASoC: Add prompt for ICS43432 codec
Without a prompt string, a config setting can't be included in a
defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards
can use the driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit
185ea05465aac8bf02a0d2b2f4289d42c72870b7
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1]
af503716ac14 ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Audiophonics I-Sabre 9038Q2M DAC driver
Signed-off-by: Audiophonics <contact@audiophonics.fr>
ASoC: i-sabre-q2m: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Added IQaudIO Pi-Codec board support (#2969)
Add support for the IQaudIO Pi-Codec board.
Signed-off-by: Gordon <gordon@iqaudio.com>
Fixed 48k timing issue
ASoC: iqaudio-codec: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
adds the Hifiberry DAC+ADC PRO version
This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Add Hifiberry DAC+DSP soundcard driver (#3224)
Adds the driver for the Hifiberry DAC+DSP. It supports capture and
playback depending on the DSP firmware.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Allow simultaneous use of JustBoom DAC and Digi
Signed-off-by: Johannes Krude <johannes@krude.de>
Pisound: MIDI communication fixes for scaled down CPU.
* Increased maximum SPI communication speed to avoid running too slow
when the CPU is scaled down and losing MIDI data.
* Keep track of buffer usage in millibytes for higher precision.
Signed-off-by: Giedrius Trainavičius <giedrius@blokas.io>
sound: Add the HiFiBerry DAC+HD version
This adds the driver for the DAC+HD version supporting HiFiBerry's
PCM179x based DACs. It also adds PLL control for clock generation.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424)
This patch fixes the board DAI setting when in master-mode.
Wrong setting could have caused random pop noise.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+ADC sound card
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards
This adds a DT overlay parameter 'leds_off' which allows
to switch off the onboard activity LEDs at all times
which has been requested by some users.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
pisound: Added reading Pisound board hardware revision and exposing it (#3425)
pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file:
/sys/kernel/pisound/hw_version
Signed-off-by: Giedrius <giedrius@blokas.io>
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting
sound: pcm512x-codec: Adding 352.8kHz samplerate support
sound/soc: only first codec is master in multicodec setup
When using multiple codecs, at most one codec should generate the master
clock. All codecs except the first are therefore configured for slave
mode.
Signed-off-by: Johannes Krude <johannes@krude.de>
ASoC: Fix snd_soc_get_pcm_runtime usage
Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link
pointer instead of a string. Patch up the downstream drivers to use
the modified API.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
[1]
4468189ff307 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()")
Add support for the AudioInjector.net Isolated sound card
This patch adds support for the Audio Injector Isolated sound card.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Add support for merus-amp soundcard and ma120x0p codec
Add 96KHz rate support to MA120X0P codec and make enable and mute gpio
pins optional.
Signed-off-by: AMuszkat <ariel.muszkat@gmail.com>
Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545)
This patch fixes a problem of the re-calculation of
i2s-clock and -parameter settings when only the ADC is activated.
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Switch to snd_soc_dai_set_bclk_ratio
Replaces obsolete function snd_soc_dai_set_tdm_slot
Signed-off-by: Joerg Schambacher <joerg@i2audio.com>
Enhances the DAC+ driver to control the optional headphone amplifier
Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter
'status' from 'disabled' to 'okay' using change_sets to enable
the headphone control.
Signed-off-by: Joerg Schambacher joerg@i2audio.com
Update Allo Piano Dac Driver
Add unique names to the individual dac coded drivers
Remove some of the codec controls that are not used.
Signed-off-by: Paul Hermann <paul@picoreplayer.org>
Fixes an onboard clock detection problem of the PRO versions
Increasing the sleep time after clock selection to 3-4ms
allows the correct detection of all combinations of DAC+ Pro
and DAC+ADC Pro sound cards and the various PI revisions.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC:ma120x0p: Increase maximum sample rate to 192KHz
Change the maximum sample rate for the amplifier to
192KHz as given in the Infineon specification.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: ma120x0p: Remove unnecessary const specifier
Clang warns:
sound/soc/codecs/ma120x0p.c:891:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_VALUE_ENUM_SINGLE_DECL(pwr_mode_ctrl,
^
./include/sound/soc.h:362:2: note: expanded from macro 'SOC_VALUE_ENUM_SINGLE_DECL'
SOC_VALUE_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xmask, xtexts, xvalues)
^
./include/sound/soc.h:359:2: note: expanded from macro 'SOC_VALUE_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_VALUE_ENUM_DOUBLE(xreg, xshift_l, xshift_r, xmask, \
^
1 warning generated.
SOC_VALUE_ENUM_DOUBLE_DECL already has a const specifier. Remove the duplicate
const to clean up the warning.
Fixes:
42444979e710 ("Add support for all the downstream rpi sound card drivers")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
ASoC: bcm: allo-piano-dac-plus: Remove unnecessary const specifiers
Clang warns:
sound/soc/bcm/allo-piano-dac-plus.c:66:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_mode_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/bcm/allo-piano-dac-plus.c:75:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_dual_mode_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/bcm/allo-piano-dac-plus.c:96:14: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const SOC_ENUM_SINGLE_DECL(allo_piano_enum,
^
./include/sound/soc.h:355:2: note: expanded from macro 'SOC_ENUM_SINGLE_DECL'
SOC_ENUM_DOUBLE_DECL(name, xreg, xshift, xshift, xtexts)
^
./include/sound/soc.h:352:2: note: expanded from macro 'SOC_ENUM_DOUBLE_DECL'
const struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
3 warnings generated.
SOC_VALUE_ENUM_DOUBLE_DECL already has a const specifier. Remove the duplicate
const specifiers to clean up the warnings.
Fixes:
42444979e710 ("Add support for all the downstream rpi sound card drivers")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
rpi-simple-soundcard: Add Dion Audio KIWI streamer
Signed-off-by: Miquel Blauw <miquelblauw@hotmail.com>
rpi-simple-soundcard: adds definitions for the HiFiBerry AMP3 card
Uses Infineon MA120x0 amplifier and supports full sample rate of 192ksps.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
sound: soc: bcm: Added Sound card driver for Dacberry400 Audio card for Raspberry Pi 400
Added Sound card driver for DACberry400 Audio card.
Signed-off-by: Ashish Vara <ashishhvara@gmail.com>
ASoC:ma120x0p: Corrects the volume level display
Fixes the wrongly changed 'limiter volume' display back to -50dB minimum
and sets the correct minimum volume level to -144dB to be aligned with
the controls and display in alsamixer etc.
Signed-off-by: Joerg Schambacher <joerg@hifiberry.com>
ASoC: bcm: Fix Rpi-PROTO and audioinjector.net Pi
As of kernel 5.19 the WM8731 driver has separate I2C and SPI support
modules. Change the Kconfig definitions for the audioinjector.net Pi
and Rpi-PROTO soundcards to select SND_SOC_WM8731_I2C.
See: https://github.com/raspberrypi/linux/issues/5364
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: adau1977: Add correct compatible strings
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
ASoC: bcm2835-i2s: Use phys addresses for DAI DMA
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
rpi sound cards: Fix Codec Zero rate switching
The Raspberry Pi Codec Zero (and IQaudIO Codec) don't notify the DA7213
codec when it needs to change PLL frequencies. As a result, audio can
be played at the wrong rate - play a 48kHz sound immediately after a
44.1kHz sound to see the effect, but in some configurations the codec
can lock into the wrong state and always get some rates wrong.
Add the necessary notification to fix the issue.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Tue, 14 Jul 2015 13:32:47 +0000 (14:32 +0100)]
mfd: Add Raspberry Pi Sense HAT core driver
mfd: Add rpi_sense_core of compatible string
Phil Elwell [Thu, 25 Jun 2015 11:16:11 +0000 (12:16 +0100)]
gpio-poweroff: Allow it to work on Raspberry Pi
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
popcornmix [Mon, 28 Nov 2016 16:50:04 +0000 (16:50 +0000)]
Improve __copy_to_user and __copy_from_user performance
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Fix copy_from_user if BCM2835_FAST_MEMCPY=n
The change which introduced CONFIG_BCM2835_FAST_MEMCPY unconditionally
changed the behaviour of arm_copy_from_user. The page pinning code
is not safe on ARMv7 if LPAE & high memory is enabled and causes
crashes which look like PTE corruption.
Make __copy_from_user_memcpy conditional on CONFIG_2835_FAST_MEMCPY=y
which is really an ARMv6 / Pi1 optimization and not necessary on newer
ARM processors.
arm: fix mmap unlocks in uaccess_with_memcpy.c
This is a regression that was added with the commit
192a4e923ef092924dd013e7326f2ec520ee4783 as of rpi-5.8.y, since that is when the move to the mmap locking API was introduced -
d8ed45c5dcd455fc5848d47f86883a1b872ac0d0
The issue is that when the patch to improve performance for the __copy_to_user and __copy_from_user functions were added for the Raspberry Pi, some of the mmaps were incorrectly mapped to write instead of read. This would cause a verity of issues, and in my case, prevent the booting of a squashfs filesystem on rpi-5.8-y and above. An example of the panic you would see from this can be seen at https://pastebin.com/raw/jBz5xCzL
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Christopher Blake <chrisrblake93@gmail.com>
arch/arm: Add __memset alias to memset_rpi.S
memset_rpi.S is an optimised memset implementation, but doesn't define
__memset (which was just added to memset.S). As a result, building
for the BCM2835 platform causes a link failure.
Add __memset as yet another alias to our common implementation.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
arm: Fix custom rpi __memset32 and __memset64
See: https://github.com/raspberrypi/linux/issues/4798
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
arm: Fix annoying .eh_frame section warnings
Replace the cfi directives with the UNWIND equivalents. This prevents
the .eh_frame section from being created, eliminating the warnings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
popcornmix [Tue, 2 Jul 2013 23:54:08 +0000 (00:54 +0100)]
Added Device IDs for August DVB-T 205
Phil Elwell [Fri, 6 Feb 2015 13:50:57 +0000 (13:50 +0000)]
leds: Add the "input" trigger, for pwr_led
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
Noralf Trønnes [Fri, 26 Jun 2015 12:25:01 +0000 (14:25 +0200)]
firmware: bcm2835: Support ARCH_BCM270x
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Noralf Trønnes [Fri, 26 Jun 2015 12:27:06 +0000 (14:27 +0200)]
char: broadcom: Add vcio module
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vcio: Add compat ioctl handling
There was no compat ioctl handler, so 32 bit userspace on a
64 bit kernel failed as IOCTL_MBOX_PROPERTY used the size
of char*.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vcio: Fail probe if rpi_firmware is not found.
Device Tree is now the only supported config mechanism, therefore
uncomment the block of code that fails the probe if the
firmware node can't be found.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
drivers: char: vcio: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
char: vcio: Rewrite as a firmware node child
The old vcio driver is a simple character device that manually locates
the firmware driver. Initialising it before the firmware driver causes
a failure, and no retries are attempted.
Rewrite vcio as a platform driver that depends on a DT node for its
instantiation and the location of the firmware driver, making use of
the miscdevice framework to reduce the code size.
N.B. Using miscdevice changes the udev SUBSYSTEM string, so a change
to the companion udev rule is required in order to continue to set
the correct device permissions, e.g.:
KERNEL="vcio", GROUP="video", MODE="0660"
See: https://github.com/raspberrypi/linux/issues/4620
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
popcornmix [Wed, 17 Jun 2015 14:44:08 +0000 (15:44 +0100)]
Add Chris Boot's i2c driver
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
projects / platform / kernel / linux-rpi.git / log