Fabio Estevam [Thu, 26 May 2022 01:09:14 +0000 (22:09 -0300)]
i2c: mxs: Silence a clang warning
[ Upstream commit
3d43273d7d1e1a5374d531e901d3c537b4c97bbf ]
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/i2c/busses/i2c-mxs.c:802:18: warning: cast to smaller integer type 'enum mxs_i2c_devtype' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes:
c32abd8b5691 ("i2c: mxs: Remove unneeded platform_device_id")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tali Perry [Wed, 25 May 2022 03:23:39 +0000 (11:23 +0800)]
i2c: npcm: Correct slave role behavior
[ Upstream commit
d7aa1b149b8fc04d802879cf4662010aa4a42deb ]
Correct the slave transaction logic to be compatible with the generic
slave backend driver.
Fixes:
56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tali Perry [Wed, 25 May 2022 03:23:38 +0000 (11:23 +0800)]
i2c: npcm: Remove own slave addresses 2:10
[ Upstream commit
47d506d1a28fd10a9fb1f33df5622d88fae72095 ]
NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes:
56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bjorn Andersson [Wed, 1 Jun 2022 23:38:18 +0000 (16:38 -0700)]
drm/bridge: lt9611uxc: Cancel only driver's work
[ Upstream commit
dfa687bffc8a4a21ed929c7dececf01b8f1f52ee ]
During device remove care needs to be taken that no work is pending
before it removes the underlying DRM bridge etc, but this can be done on
the specific work rather than waiting for the flush of the system-wide
workqueue.
Fixes:
bc6fa8676ebb ("drm/bridge/lontium-lt9611uxc: move HPD notification out of IRQ handler")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601233818.1877963-1-bjorn.andersson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Wed, 1 Jun 2022 03:39:27 +0000 (07:39 +0400)]
drm/meson: encoder_hdmi: Fix refcount leak in meson_encoder_hdmi_init
[ Upstream commit
d82a5a4aae9d0203234737caed1bf470aa317568 ]
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes:
e67f6037ae1b ("drm/meson: split out encoder from meson_dw_hdmi")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601033927.47814-3-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Neil Armstrong [Wed, 20 Oct 2021 12:39:45 +0000 (14:39 +0200)]
drm/meson: encoder_hdmi: switch to bridge DRM_BRIDGE_ATTACH_NO_CONNECTOR
[ Upstream commit
0af5e0b41110e2da872030395231ab19c45be931 ]
This implements the necessary change to no more use the embedded
connector in dw-hdmi and use the dedicated bridge connector driver
by passing DRM_BRIDGE_ATTACH_NO_CONNECTOR to the bridge attach call.
The necessary connector properties are added to handle the same
functionalities as the embedded dw-hdmi connector, i.e. the HDR
metadata, the CEC notifier & other flags.
The dw-hdmi output_port is set to 1 in order to look for a connector
next bridge in order to get DRM_BRIDGE_ATTACH_NO_CONNECTOR working.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020123947.2585572-5-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xinlei Lee [Fri, 20 May 2022 02:00:07 +0000 (10:00 +0800)]
drm/mediatek: Add pull-down MIPI operation in mtk_dsi_poweroff function
[ Upstream commit
fa5d0a0205c34734c5b8daa77e39ac2817f63a10 ]
In the dsi_enable function, mtk_dsi_rxtx_control is to
pull up the MIPI signal operation. Before dsi_disable,
MIPI should also be pulled down by writing a register
instead of disabling dsi.
If disable dsi without pulling the mipi signal low, the value of
the register will still maintain the setting of the mipi signal being
pulled high.
After resume, even if the mipi signal is not pulled high, it will still
be in the high state.
Fixes:
2e54c14e310f ("drm/mediatek: Add DSI sub driver")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-5-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jitao Shi [Fri, 20 May 2022 02:00:05 +0000 (10:00 +0800)]
drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs
[ Upstream commit
cde7e2e35c2866d22a3a012e72a41052dfcc255d ]
In order to match the changes of "Use the drm_panel_bridge API",
the poweron/poweroff of dsi is extracted from enable/disable and
defined as new funcs (atomic_pre_enable/atomic_post_disable).
Since dsi_poweron is moved from dsi_enable to pre_enable function, in
order to avoid poweron failure, the operation of dsi register fails to
cause bus hang. Therefore, the protection mechanism is added to the
dsi_enable function.
Fixes:
2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-3-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xinlei Lee [Fri, 20 May 2022 02:00:04 +0000 (10:00 +0800)]
drm/mediatek: Modify dsi funcs to atomic operations
[ Upstream commit
7f6335c6a258edf4d5ff1b904bc033188dc7b48b ]
Because .enable & .disable are deprecated.
Use .atomic_enable & .atomic_disable instead.
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-2-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexey Kodanev [Mon, 6 Jun 2022 13:50:54 +0000 (16:50 +0300)]
drm/radeon: fix potential buffer overflow in ni_set_mc_special_registers()
[ Upstream commit
136f614931a2bb73616b292cf542da3a18daefd5 ]
The last case label can write two buffers 'mc_reg_address[j]' and
'mc_data[j]' with 'j' offset equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE
since there are no checks for this value in both case labels after the
last 'j++'.
Instead of changing '>' to '>=' there, add the bounds check at the start
of the second 'case' (the first one already has it).
Also, remove redundant last checks for 'j' index bigger than array size.
The expression is always false. Moreover, before or after the patch
'table->last' can be equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE and it
seems it can be a valid value.
Detected using the static analysis tool - Svace.
Fixes:
69e0b57a91ad ("drm/radeon/kms: add dpm support for cayman (v5)")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Manikanta Pubbisetty [Thu, 2 Jun 2022 11:56:21 +0000 (17:26 +0530)]
ath11k: Fix incorrect debug_mask mappings
[ Upstream commit
9331f7d3c54a263bede5055e106e40b28d0bd937 ]
Currently a couple of debug_mask entries are mapped to the same value,
this could enable unintended driver logging. If enabling DP_TX logs was
the intention, then this could also enable PCI logs flooding the dmesg
buffer or vice versa. Fix this by correctly assigning the debug masks.
Found during code review.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes:
aa2092a9bab3f ("ath11k: add raw mode and software crypto support")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602115621.15339-1-quic_mpubbise@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yunhao Tian [Tue, 10 May 2022 03:02:19 +0000 (11:02 +0800)]
drm/mipi-dbi: align max_chunk to 2 in spi_transfer
[ Upstream commit
435c249008cba04ed6a7975e9411f3b934620204 ]
In __spi_validate, there's a validation that no partial transfers
are accepted (xfer->len % w_size must be zero). When
max_chunk is not a multiple of bpw (e.g. max_chunk = 65535,
bpw = 16), the transfer will be rejected.
This patch aligns max_chunk to 2 bytes (the maximum value of bpw is 16),
so that no partial transfer will occur.
Fixes:
d23d4d4dac01 ("drm/tinydrm: Move tinydrm_spi_transfer()")
Signed-off-by: Yunhao Tian <t123yh.xyz@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510030219.2486687-1-t123yh.xyz@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johan Hovold [Sun, 22 May 2022 12:33:16 +0000 (15:33 +0300)]
ath11k: fix netdev open race
[ Upstream commit
d4ba1ff87b17e81686ada8f429300876f55f95ad ]
Make sure to allocate resources needed before registering the device.
This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.
I did not see this issue with next-
20220310, but I hit it on every probe
with next-
20220511. Perhaps some timing changed in between.
Here's the backtrace:
[ 51.346947] kernel BUG at kernel/time/timer.c:990!
[ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 51.578225] Call trace:
[ 51.583293] __mod_timer+0x298/0x390
[ 51.589518] mod_timer+0x14/0x20
[ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k]
[ 51.603165] drv_start+0x38/0x60 [mac80211]
[ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211]
[ 51.617945] ieee80211_open+0x60/0xb0 [mac80211]
[ 51.625311] __dev_open+0x100/0x1c0
[ 51.631420] __dev_change_flags+0x194/0x210
[ 51.638214] dev_change_flags+0x24/0x70
[ 51.644646] do_setlink+0x228/0xdb0
[ 51.650723] __rtnl_newlink+0x460/0x830
[ 51.657162] rtnl_newlink+0x4c/0x80
[ 51.663229] rtnetlink_rcv_msg+0x124/0x390
[ 51.669917] netlink_rcv_skb+0x58/0x130
[ 51.676314] rtnetlink_rcv+0x18/0x30
[ 51.682460] netlink_unicast+0x250/0x310
[ 51.688960] netlink_sendmsg+0x19c/0x3e0
[ 51.695458] ____sys_sendmsg+0x220/0x290
[ 51.701938] ___sys_sendmsg+0x7c/0xc0
[ 51.708148] __sys_sendmsg+0x68/0xd0
[ 51.714254] __arm64_sys_sendmsg+0x28/0x40
[ 51.720900] invoke_syscall+0x48/0x120
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes:
d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Fixes:
840c36fa727a ("ath11k: dp: stop rx pktlog before suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517103436.15867-1-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Carpenter [Tue, 17 May 2022 11:48:44 +0000 (14:48 +0300)]
wifi: rtlwifi: fix error codes in rtl_debugfs_set_write_h2c()
[ Upstream commit
b88d28146c30a8e14f0f012d56ebf19b68a348f4 ]
If the copy_from_user() fails or the user gives invalid date then the
correct thing to do is to return a negative error code. (Currently it
returns success).
I made a copy additional related cleanups:
1) There is no need to check "buffer" for NULL. That's handled by
copy_from_user().
2) The "h2c_len" variable cannot be negative because it is unsigned
and because sscanf() does not return negative error codes.
Fixes:
610247f46feb ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YoOLnDkHgVltyXK7@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
Gao Chao [Tue, 24 May 2022 02:45:51 +0000 (10:45 +0800)]
drm/panel: Fix build error when CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y && CONFIG_DRM_DISPLAY_HELPER=m
[ Upstream commit
a67664860f7833015a683ea295f7c79ac2901332 ]
If CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y && CONFIG_DRM_DISPLAY_HELPER=m,
bulding fails:
drivers/gpu/drm/panel/panel-samsung-atna33xc20.o: In function `atana33xc20_probe':
panel-samsung-atna33xc20.c:(.text+0x744): undefined reference to
`drm_panel_dp_aux_backlight'
make: *** [vmlinux] Error 1
Let CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20 select DRM_DISPLAY_DP_HELPER and
CONFIG_DRM_DISPLAY_HELPER to fix this error.
Fixes:
32ce3b320343 ("drm/panel: atna33xc20: Introduce the Samsung ATNA33XC20 panel")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Gao Chao <gaochao49@huawei.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220524024551.539-1-gaochao49@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Javier Martinez Canillas [Fri, 20 May 2022 09:16:02 +0000 (11:16 +0200)]
drm/st7735r: Fix module autoloading for Okaya RH128128T
[ Upstream commit
9ad6f181ad9a19a26bda73a7b199df44ccfcdaba ]
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was
registered via OF. This means that the st7735r.ko module won't autoload if
a DT has a node with a compatible "okaya,rh128128t" string.
In that case, kmod expects a "MODALIAS=of:N*T*Cokaya,rh128128t" uevent but
instead will get a "MODALIAS=spi:rh128128t", which is not present in the
list of aliases:
$ modinfo drivers/gpu/drm/tiny/st7735r.ko | grep alias
alias: of:N*T*Cokaya,rh128128tC*
alias: of:N*T*Cokaya,rh128128t
alias: of:N*T*Cjianda,jd-t18003-t01C*
alias: of:N*T*Cjianda,jd-t18003-t01
alias: spi:jd-t18003-t01
To workaround this issue, add in the SPI table an entry for that device.
Fixes:
d1d511d516f7 ("drm: tiny: st7735r: Add support for Okaya RH128128T")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520091602.179078-1-javierm@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Krzysztof Kozlowski [Wed, 18 May 2022 07:27:26 +0000 (10:27 +0300)]
ath10k: do not enforce interrupt trigger type
[ Upstream commit
1ee6c5abebd3cacf2ac4378d0ed4f57fd4850421 ]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge rising - but instead rely on Devicetree to configure it.
All Qualcomm DTSI with WCN3990 define the interrupt type as level high,
so the mismatch between DTSI and driver causes rebind issues:
$ echo
18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/unbind
$ echo
18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/bind
[ 44.763114] irq: type mismatch, failed to map hwirq-446 for interrupt-controller@
17a00000!
[ 44.763130] ath10k_snoc
18800000.wifi: error -ENXIO: IRQ index 0 not found
[ 44.763140] ath10k_snoc
18800000.wifi: failed to initialize resource: -6
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.0.c8-00009-QCAHLSWSC8180XMTPLZ-1
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Fixes:
c963a683e701 ("ath10k: add resource init and deinit for WCN3990")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220513151516.357549-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marek Vasut [Tue, 29 Mar 2022 08:50:10 +0000 (10:50 +0200)]
drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated function
[ Upstream commit
8478095a8c4bcea3c83b0767d6c9127434160761 ]
The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is
currently supported. In order to support the rest of the modes without
making the tc_probe() overly long, split the bridge endpoint parsing
into dedicated function, where the necessary logic to detect the bridge
mode based on which endpoints are connected, can be implemented.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-7-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
Douglas Anderson [Tue, 10 May 2022 19:29:41 +0000 (12:29 -0700)]
drm/dp: Export symbol / kerneldoc fixes for DP AUX bus
[ Upstream commit
39c28cdfb719f0e306b447f0827dfd712f81858b ]
While working on the DP AUX bus code I found a few small things that
should be fixed. Namely the non-devm version of
of_dp_aux_populate_ep_devices() was missing an export. There was also
an extra blank line in a kerneldoc and a kerneldoc that incorrectly
documented a return value. Fix these.
Fixes:
aeb33699fc2c ("drm: Introduce the DP AUX bus")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510122726.v3.1.Ia91f4849adfc5eb9da1eb37ba79aa65fb3c95a0f@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Tue, 12 Jul 2022 16:15:19 +0000 (18:15 +0200)]
pwm: lpc18xx: Fix period handling
[ Upstream commit
8933d30c5f468d6cc1e4bf9bb535149da35f202e ]
The calculation:
val = (u64)NSEC_PER_SEC * LPC18XX_PWM_TIMER_MAX;
do_div(val, lpc18xx_pwm->clk_rate);
lpc18xx_pwm->max_period_ns = val;
is bogus because with NSEC_PER_SEC =
1000000000,
LPC18XX_PWM_TIMER_MAX = 0xffffffff and clk_rate < NSEC_PER_SEC this
overflows the (on lpc18xx (i.e. ARM32) 32 bit wide) unsigned int
.max_period_ns. This results (dependant of the actual clk rate) in an
arbitrary limitation of the maximal period. E.g. for clkrate =
333333333 (Hz) we get max_period_ns = 9 instead of
12884901897.
So make .max_period_ns an u64 and pass period and duty as u64 to not
discard relevant digits. And also make use of mul_u64_u64_div_u64()
which prevents all overflows assuming clk_rate < NSEC_PER_SEC.
Fixes:
841e6f90bb78 ("pwm: NXP LPC18xx PWM/SCT driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Wed, 10 Nov 2021 08:49:50 +0000 (09:49 +0100)]
pwm: lpc18xx-sct: Simplify driver by not using pwm_[gs]et_chip_data()
[ Upstream commit
9136a39e6cf69e49803ac6123a4ac4431bc915a2 ]
The per-channel data is available directly in the driver data struct. So
use it without making use of pwm_[gs]et_chip_data().
The relevant change introduced by this patch to lpc18xx_pwm_disable() at
the assembler level (for an arm lpc18xx_defconfig build) is:
push {r3, r4, r5, lr}
mov r4, r0
mov r0, r1
mov r5, r1
bl 0 <pwm_get_chip_data>
ldr r3, [r0, #0]
changes to
ldr r3, [r1, #8]
push {r4, lr}
add.w r3, r0, r3, lsl #2
ldr r3, [r3, #92] ; 0x5c
So this reduces stack usage, has an improved runtime behavior because of
better pipeline usage, doesn't branch to an external function and the
generated code is a bit smaller occupying less memory.
The codesize of lpc18xx_pwm_probe() is reduced by 32 bytes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Wed, 10 Nov 2021 08:49:49 +0000 (09:49 +0100)]
pwm: lpc18xx-sct: Reduce number of devm memory allocations
[ Upstream commit
20d9de9c4d6642bb40c935233697723b56573cbc ]
Each devm allocations has an overhead of 24 bytes to store the related
struct devres_node additionally to the fragmentation of the allocator.
So allocating 16 struct lpc18xx_pwm_data (which only hold a single int)
adds quite some overhead. Instead put the per-channel data into the
driver data struct and allocate it in one go.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Thu, 21 Jul 2022 10:31:29 +0000 (12:31 +0200)]
pwm: sifive: Shut down hardware only after pwmchip_remove() completed
[ Upstream commit
2375e964d541bb09158cd2dff67b5d74e8de61cd ]
The PWMs are expected to be functional until pwmchip_remove() is called.
So disable the clks only afterwards.
Fixes:
9e37a53eb051 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Thu, 21 Jul 2022 10:31:28 +0000 (12:31 +0200)]
pwm: sifive: Ensure the clk is enabled exactly once per running PWM
[ Upstream commit
ace41d7564e655c39f709a78c035188a460c7cbd ]
.apply() assumes the clk to be for a given PWM iff the PWM is enabled.
So make sure this is the case when .probe() completes. And in .remove()
disable the according number of times.
This fixes a clk enable/disable imbalance, if some PWMs are already running
at probe time.
Fixes:
9e37a53eb051 (pwm: sifive: Add a driver for SiFive SoC PWM)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Uwe Kleine-König [Thu, 21 Jul 2022 10:31:23 +0000 (12:31 +0200)]
pwm: sifive: Simplify offset calculation for PWMCMP registers
[ Upstream commit
20550a61880fc55e68a0d290ad195b74729c0e7b ]
Instead of explicitly using PWM_SIFIVE_PWMCMP0 + pwm->hwpwm *
PWM_SIFIVE_SIZE_PWMCMP for each access to one of the PWMCMP registers,
introduce a macro that takes the hwpwm id as parameter.
For the register definition using a plain 4 instead of the cpp constant
PWM_SIFIVE_SIZE_PWMCMP is easier to read, so define the offset macro
without the constant. The latter can then be dropped as there are no
users left.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Snitzer [Fri, 22 Jul 2022 19:31:23 +0000 (15:31 -0400)]
dm: return early from dm_pr_call() if DM device is suspended
[ Upstream commit
e120a5f1e78fab6223544e425015f393d90d6f0d ]
Otherwise PR ops may be issued while the broader DM device is being
reconfigured, etc.
Fixes:
9c72bad1f31a ("dm: call PR reserve/unreserve on each underlying device")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Markus Mayer [Mon, 18 Jul 2022 03:10:39 +0000 (20:10 -0700)]
thermal/tools/tmon: Include pthread and time headers in tmon.h
[ Upstream commit
0cf51bfe999524377fbb71becb583b4ca6d07cfc ]
Include sys/time.h and pthread.h in tmon.h, so that types
"pthread_mutex_t" and "struct timeval tv" are known when tmon.h
references them.
Without these headers, compiling tmon against musl-libc will fail with
these errors:
In file included from sysfs.c:31:0:
tmon.h:47:8: error: unknown type name 'pthread_mutex_t'
extern pthread_mutex_t input_lock;
^~~~~~~~~~~~~~~
make[3]: *** [<builtin>: sysfs.o] Error 1
make[3]: *** Waiting for unfinished jobs....
In file included from tui.c:31:0:
tmon.h:54:17: error: field 'tv' has incomplete type
struct timeval tv;
^~
make[3]: *** [<builtin>: tui.o] Error 1
make[2]: *** [Makefile:83: tmon] Error 2
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Acked-by: Alejandro González <alejandro.gonzalez.correo@gmail.com>
Tested-by: Alejandro González <alejandro.gonzalez.correo@gmail.com>
Fixes:
94f69966faf8 ("tools/thermal: Introduce tmon, a tool for thermal subsystem")
Link: https://lore.kernel.org/r/20220718031040.44714-1-f.fainelli@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
YiFei Zhu [Thu, 26 May 2022 22:34:07 +0000 (22:34 +0000)]
selftests/seccomp: Fix compile warning when CC=clang
[ Upstream commit
3ce4b78f73e8e00fb86bad67ee7f6fe12019707e ]
clang has -Wconstant-conversion by default, and the constant 0xAAAAAAAAA
(9 As) being converted to an int, which is generally 32 bits, results
in the compile warning:
clang -Wl,-no-as-needed -Wall -isystem ../../../../usr/include/ -lpthread seccomp_bpf.c -lcap -o seccomp_bpf
seccomp_bpf.c:812:67: warning: implicit conversion from 'long' to 'int' changes value from
45812984490 to -
1431655766 [-Wconstant-conversion]
int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAAA;
~~~~ ^~~~~~~~~~~
1 warning generated.
-
1431655766 is the expected truncation, 0xAAAAAAAA (8 As), so use
this directly in the code to avoid the warning.
Fixes:
3932fcecd962 ("selftests/seccomp: Add test for unknown SECCOMP_RET kill behavior")
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220526223407.1686936-1-zhuyifei@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peter Zijlstra [Fri, 17 Jun 2022 14:52:06 +0000 (16:52 +0200)]
x86/extable: Fix ex_handler_msr() print condition
[ Upstream commit
a1a5482a2c6e38a3ebed32e571625c56a8cc41a6 ]
On Fri, Jun 17, 2022 at 02:08:52PM +0300, Stephane Eranian wrote:
> Some changes to the way invalid MSR accesses are reported by the
> kernel is causing some problems with messages printed on the
> console.
>
> We have seen several cases of ex_handler_msr() printing invalid MSR
> accesses once but the callstack multiple times causing confusion on
> the console.
> The problem here is that another earlier commit (5.13):
>
>
a358f40600b3 ("once: implement DO_ONCE_LITE for non-fast-path "do once" functionality")
>
> Modifies all the pr_*_once() calls to always return true claiming
> that no caller is ever checking the return value of the functions.
>
> This is why we are seeing the callstack printed without the
> associated printk() msg.
Extract the ONCE_IF(cond) part into __ONCE_LTE_IF() and use that to
implement DO_ONCE_LITE_IF() and fix the extable code.
Fixes:
a358f40600b3 ("once: implement DO_ONCE_LITE for non-fast-path "do once" functionality")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Stephane Eranian <eranian@google.com>
Link: https://lkml.kernel.org/r/YqyVFsbviKjVGGZ9@worktop.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nicolas Saenz Julienne [Tue, 28 Jun 2022 09:22:59 +0000 (11:22 +0200)]
nohz/full, sched/rt: Fix missed tick-reenabling bug in dequeue_task_rt()
[ Upstream commit
5c66d1b9b30f737fcef85a0b75bfe0590e16b62a ]
dequeue_task_rt() only decrements 'rt_rq->rt_nr_running' after having
called sched_update_tick_dependency() preventing it from re-enabling the
tick on systems that no longer have pending SCHED_RT tasks but have
multiple runnable SCHED_OTHER tasks:
dequeue_task_rt()
dequeue_rt_entity()
dequeue_rt_stack()
dequeue_top_rt_rq()
sub_nr_running() // decrements rq->nr_running
sched_update_tick_dependency()
sched_can_stop_tick() // checks rq->rt.rt_nr_running,
...
__dequeue_rt_entity()
dec_rt_tasks() // decrements rq->rt.rt_nr_running
...
Every other scheduler class performs the operation in the opposite
order, and sched_update_tick_dependency() expects the values to be
updated as such. So avoid the misbehaviour by inverting the order in
which the above operations are performed in the RT scheduler.
Fixes:
76d92ac305f2 ("sched: Migrate sched to use new tick dependency mask model")
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
Reviewed-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220628092259.330171-1-nsaenzju@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Anshuman Khandual [Thu, 14 Jul 2022 06:13:02 +0000 (11:43 +0530)]
drivers/perf: arm_spe: Fix consistency of SYS_PMSCR_EL1.CX
[ Upstream commit
92f2b8bafa3d6e89c750e9d301a8b7ab76aaa8b6 ]
The arm_spe_pmu driver will enable SYS_PMSCR_EL1.CX in order to add CONTEXT
packets into the traces, if the owner of the perf event runs with required
capabilities i.e CAP_PERFMON or CAP_SYS_ADMIN via perfmon_capable() helper.
The value of this bit is computed in the arm_spe_event_to_pmscr() function
but the check for capabilities happens in the pmu event init callback i.e
arm_spe_pmu_event_init(). This suggests that the value of the CX bit should
remain consistent for the duration of the perf session.
However, the function arm_spe_event_to_pmscr() may be called later during
the event start callback i.e arm_spe_pmu_start() when the "current" process
is not the owner of the perf session, hence the CX bit setting is currently
not consistent.
One way to fix this, is by caching the required value of the CX bit during
the initialization of the PMU event, so that it remains consistent for the
duration of the session. It uses currently unused 'event->hw.flags' element
to cache perfmon_capable() value, which can be referred during event start
callback to compute SYS_PMSCR_EL1.CX. This ensures consistent availability
of context packets in the trace as per event owner capabilities.
Drop BIT(SYS_PMSCR_EL1_CX_SHIFT) check in arm_spe_pmu_event_init(), because
now CX bit cannot be set in arm_spe_event_to_pmscr() with perfmon_capable()
disabled.
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Fixes:
d5d9696b0380 ("drivers/perf: Add support for ARMv8.2 Statistical Profiling Extension")
Reported-by: German Gomez <german.gomez@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20220714061302.2715102-1-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xu Qiang [Tue, 19 Jul 2022 06:36:40 +0000 (06:36 +0000)]
irqdomain: Report irq number for NOMAP domains
[ Upstream commit
6f194c99f466147148cc08452718b46664112548 ]
When using a NOMAP domain, __irq_resolve_mapping() doesn't store
the Linux IRQ number at the address optionally provided by the caller.
While this isn't a huge deal (the returned value is guaranteed
to the hwirq that was passed as a parameter), let's honour the letter
of the API by writing the expected value.
Fixes:
d22558dd0a6c (“irqdomain: Introduce irq_resolve_mapping()”)
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
[maz: commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220719063641.56541-2-xuqiang36@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sumit Garg [Mon, 11 Jul 2022 08:30:38 +0000 (14:00 +0530)]
arm64: dts: qcom: qcs404: Fix incorrect USB2 PHYs assignment
[ Upstream commit
58577966a42fc0b660b5e2c7c9e5a2241363ea83 ]
Currently the DT for QCS404 SoC has setup for 2 USB2 PHYs with one each
assigned to USB3 controller and USB2 controller. This assignment is
incorrect which only works by luck: as when each USB HCI comes up it
configures the *other* controllers PHY which is enough to make them
happy. If, for any reason, we were to disable one of the controllers then
both would stop working.
This was a difficult inconsistency to be caught which was found while
trying to enable USB support in u-boot. So with all the required drivers
ported to u-boot, I couldn't get the same USB storage device enumerated
in u-boot which was being enumerated fine by the kernel.
The root cause of the problem came out to be that I wasn't enabling USB2
PHY: "usb2_phy_prim" in u-boot. Then I realised that via simply disabling
the same USB2 PHY currently assigned to USB2 host controller in the
kernel disabled enumeration for USB3 host controller as well.
So fix this inconsistency by correctly assigning USB2 PHYs.
Fixes:
9375e7d719b3 ("arm64: dts: qcom: qcs404: Add USB devices and PHYs")
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220711083038.1518529-1-sumit.garg@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Konrad Dybcio [Thu, 7 Jul 2022 21:21:58 +0000 (23:21 +0200)]
soc: qcom: Make QCOM_RPMPD depend on PM
[ Upstream commit
a6232f2aa99ce470799992e99e0012945bb5308f ]
QCOM_RPMPD requires PM_GENERIC_DOMAINS/_OF, which in turns requires
CONFIG_PM. I forgot about the latter in my earlier patch (it's still
in -next as of the time of committing, hence no Fixes: tag). Fix it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220707212158.32684-1-konrad.dybcio@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Liang He [Fri, 15 Jul 2022 11:10:27 +0000 (19:10 +0800)]
regulator: of: Fix refcount leak bug in of_get_regulation_constraints()
[ Upstream commit
66efb665cd5ad69b27dca8571bf89fc6b9c628a4 ]
We should call the of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes:
40e20d68bb3f ("regulator: of: Add support for parsing regulator_state for suspend state")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220715111027.391032-1-windhl@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mikulas Patocka [Mon, 11 Jul 2022 20:31:52 +0000 (16:31 -0400)]
dm writecache: count number of blocks discarded, not number of discard bios
[ Upstream commit
2ee73ef60db4d79b9f9b8cd501e8188b5179449f ]
Change dm-writecache, so that it counts the number of blocks discarded
instead of the number of discard bios. Make it consistent with the
read and write statistics counters that were changed to count the
number of blocks instead of bios.
Fixes:
e3a35d03407c ("dm writecache: add event counters")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mikulas Patocka [Mon, 11 Jul 2022 20:31:26 +0000 (16:31 -0400)]
dm writecache: count number of blocks written, not number of write bios
[ Upstream commit
b2676e1482af89714af6988ce5d31a84692e2530 ]
Change dm-writecache, so that it counts the number of blocks written
instead of the number of write bios. Bios can be split and requeued
using the dm_accept_partial_bio function, so counting bios caused
inaccurate results.
Fixes:
e3a35d03407c ("dm writecache: add event counters")
Reported-by: Yu Kuai <yukuai1@huaweicloud.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mikulas Patocka [Mon, 11 Jul 2022 20:30:52 +0000 (16:30 -0400)]
dm writecache: count number of blocks read, not number of read bios
[ Upstream commit
2c6e755b49d273243431f5f1184654e71221fc78 ]
Change dm-writecache, so that it counts the number of blocks read
instead of the number of read bios. Bios can be split and requeued
using the dm_accept_partial_bio function, so counting bios caused
inaccurate results.
Fixes:
e3a35d03407c ("dm writecache: add event counters")
Reported-by: Yu Kuai <yukuai1@huaweicloud.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mikulas Patocka [Mon, 11 Jul 2022 20:30:27 +0000 (16:30 -0400)]
dm writecache: return void from functions
[ Upstream commit
9bc0c92e4b82adb017026dbb2aa816b1ac2bef31 ]
The functions writecache_map_remap_origin and writecache_bio_copy_ssd
only return a single value, thus they can be made to return void.
This helps simplify the following IO accounting changes.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hsin-Yi Wang [Tue, 5 Jul 2022 17:16:49 +0000 (01:16 +0800)]
PM: domains: Ensure genpd_debugfs_dir exists before remove
[ Upstream commit
37101d3c719386040ded735a5ec06974f1d94d1f ]
Both genpd_debug_add() and genpd_debug_remove() may be called
indirectly by other drivers while genpd_debugfs_dir is not yet
set. For example, drivers can call pm_genpd_init() in probe or
pm_genpd_init() in probe fail/cleanup path:
pm_genpd_init()
--> genpd_debug_add()
pm_genpd_remove()
--> genpd_remove()
--> genpd_debug_remove()
At this time, genpd_debug_init() may not yet be called.
genpd_debug_add() checks that if genpd_debugfs_dir is NULL, it
will return directly. Make sure this is also checked
in pm_genpd_remove(), otherwise components under debugfs root
which has the same name as other components under pm_genpd may
be accidentally removed, since NULL represents debugfs root.
Fixes:
718072ceb211 ("PM: domains: create debugfs nodes when adding power domains")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bart Van Assche [Thu, 14 Jul 2022 18:06:36 +0000 (11:06 -0700)]
blktrace: Trace remapped requests correctly
[ Upstream commit
22c80aac882f712897b88b7ea8f5a74ea19019df ]
Trace the remapped operation and its flags instead of only the data
direction of remapped operations. This issue was detected by analyzing
the warnings reported by sparse related to the new blk_opf_t type.
Reviewed-by: Jun'ichi Nomura <junichi.nomura@nec.com>
Cc: Mike Snitzer <snitzer@kernel.org>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Fixes:
1b9a9ab78b0a ("blktrace: use op accessors")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-11-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Linus Walleij [Tue, 12 Jul 2022 21:46:24 +0000 (23:46 +0200)]
hwmon: (drivetemp) Add module alias
[ Upstream commit
5918036cfa8ded7aa8094db70295011ce2275447 ]
Adding a MODULE_ALIAS() to drivetemp will make the driver easier
for modprobe to autoprobe.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220712214624.1845158-1-linus.walleij@linaro.org
Fixes:
5b46903d8bf3 ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Wed, 13 Jul 2022 09:40:23 +0000 (17:40 +0800)]
spi: tegra20-slink: fix UAF in tegra_slink_remove()
[ Upstream commit
7e9984d183bb1e99e766c5c2b950ff21f7f7b6c0 ]
After calling spi_unregister_master(), the refcount of master will
be decrease to 0, and it will be freed in spi_controller_release(),
the device data also will be freed, so it will lead a UAF when using
'tspi'. To fix this, get the master before unregister and put it when
finish using it.
Fixes:
26c863418221 ("spi: tegra20-slink: Don't use resource-managed spi_register helper")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220713094024.1508869-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Tue, 12 Jul 2022 13:55:04 +0000 (21:55 +0800)]
spi: Fix simplification of devm_spi_register_controller
[ Upstream commit
43cc5a0afe4184a7fafe1eba32b5a11bb69c9ce0 ]
This reverts commit
59ebbe40fb51 ("spi: simplify
devm_spi_register_controller").
If devm_add_action() fails in devm_add_action_or_reset(),
devm_spi_unregister() will be called, it decreases the
refcount of 'ctlr->dev' to 0, then it will cause uaf in
the drivers that calling spi_put_controller() in error path.
Fixes:
59ebbe40fb51 ("spi: simplify devm_spi_register_controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220712135504.1055688-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ming Lei [Mon, 11 Jul 2022 09:08:08 +0000 (17:08 +0800)]
blk-mq: don't create hctx debugfs dir until q->debugfs_dir is created
[ Upstream commit
f3ec5d11554778c24ac8915e847223ed71d104fc ]
blk_mq_debugfs_register_hctx() can be called by blk_mq_update_nr_hw_queues
when gendisk isn't added yet, such as nvme tcp.
Fixes the warning of 'debugfs: Directory 'hctx0' with parent '/' already present!'
which can be observed reliably when running blktests nvme/005.
Fixes:
6cfc0081b046 ("blk-mq: no need to check return value of debugfs_create functions")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220711090808.259682-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Gao Xiang [Fri, 8 Jul 2022 10:10:01 +0000 (18:10 +0800)]
erofs: avoid consecutive detection for Highmem memory
[ Upstream commit
448b5a1548d87c246c3d0c3df8480d3c6eb6c11a ]
Currently, vmap()s are avoided if physical addresses are
consecutive for decompressed buffers.
I observed that is very common for 4KiB pclusters since the
numbers of decompressed pages are almost 2 or 3.
However, such detection doesn't work for Highmem pages on
32-bit machines, let's fix it now.
Reported-by: Liu Jinbao <liujinbao1@xiaomi.com>
Fixes:
7fc45dbc938a ("staging: erofs: introduce generic decompression backend")
Link: https://lore.kernel.org/r/20220708101001.21242-1-hsiangkao@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tamás Szűcs [Sun, 12 Jun 2022 14:59:45 +0000 (14:59 +0000)]
arm64: tegra: Fix SDMMC1 CD on P2888
[ Upstream commit
b415bb7c976f1d595ed752001c0938f702645dab ]
Hook SDMMC1 CD up with CVM GPIO02 (SOC_GPIO11) used for card detection on J4
(uSD socket) on the carrier.
Fixes:
ef633bfc21e9 ("arm64: tegra: Enable card detect for SD card on P2888")
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mikko Perttunen [Wed, 22 Jun 2022 13:23:00 +0000 (16:23 +0300)]
arm64: tegra: Mark BPMP channels as no-memory-wc
[ Upstream commit
61192a9d8a6367ae1b8234876941b037910a2459 ]
The Tegra SYSRAM contains regions access to which is restricted to
certain hardware blocks on the system, and speculative accesses to
those will cause issues.
Patch 'misc: sram: Only map reserved areas in Tegra SYSRAM' attempted
to resolve this by only mapping the regions specified in the device
tree on the assumption that there are no such restricted areas within
the 64K-aligned area of memory that contains the memory we wish to map.
Turns out this assumption is wrong, as there are such areas above the
4K pages described in the device trees. As such, we need to use the
bigger hammer that is no-memory-wc, which causes the memory to be
mapped as Device memory to which speculative accesses are disallowed.
As such, the previous patch in the series,
'firmware: tegra: bpmp: do only aligned access to IPC memory area',
is required with this patch to make the BPMP driver only issue aligned
memory accesses as those are also required with Device memory.
Fixes:
fec29bf04994 ("misc: sram: Only map reserved areas in Tegra SYSRAM")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mikko Perttunen [Fri, 12 Nov 2021 12:35:39 +0000 (13:35 +0100)]
arm64: tegra: Update Tegra234 BPMP channel addresses
[ Upstream commit
98094be152d34f8014ca67fbdc210e5261c4b09d ]
On final Tegra234 systems, shared memory for communication with BPMP is
located at offset 0x70000 in SYSRAM.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thierry Reding [Fri, 12 Nov 2021 12:35:37 +0000 (13:35 +0100)]
arm64: tegra: Fixup SYSRAM references
[ Upstream commit
7fa307524a4d721d4a04523018509882c5414e72 ]
The json-schema bindings for SRAM expect the nodes to be called "sram"
rather than "sysram" or "shmem". Furthermore, place the brackets around
the SYSRAM references such that a two-element array is created rather
than a two-element array nested in a single-element array. This is not
relevant for device tree itself, but allows the nodes to be properly
validated against json-schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nick Hainke [Thu, 30 Jun 2022 11:16:57 +0000 (13:16 +0200)]
arm64: dts: mt7622: fix BPI-R64 WPS button
[ Upstream commit
c98e6e683632386a3bd284acda4342e68aec4c41 ]
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
Fixes:
0b6286dd96c0 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://lore.kernel.org/r/20220630111746.4098-1-vincent@systemli.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johan Hovold [Tue, 5 Jul 2022 11:40:20 +0000 (13:40 +0200)]
arm64: dts: qcom: sm8250: add missing PCIe PHY clock-cells
[ Upstream commit
d9fd162ce764c227fcfd4242f6c1639895a9481f ]
Add the missing '#clock-cells' properties to the PCIe QMP PHY nodes.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Fixes:
e53bdfc00977 ("arm64: dts: qcom: sm8250: Add PCIe support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220705114032.22787-3-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marijn Suijten [Sun, 8 May 2022 10:03:34 +0000 (12:03 +0200)]
arm64: dts: qcom: sm6125: Append -state suffix to pinctrl nodes
[ Upstream commit
cbfb5668aece448877fa7826cde81c9d06f4a4ac ]
According to qcom,sm6125-pinctrl.yaml all nodes inside the tlmm must be
suffixed by -state:
qcom/sm6125-sony-xperia-seine-pdx201.dtb: pinctrl@500000: 'sdc2-off', 'sdc2-on' do not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
The label names have been updated to match, going from sdc2_state_X to
sdc2_X_state.
Fixes:
cff4bbaf2a2d ("arm64: dts: qcom: Add support for SM6125")
Fixes:
82e1783890b7 ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220508100336.127176-2-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marijn Suijten [Sun, 8 May 2022 10:03:33 +0000 (12:03 +0200)]
arm64: dts: qcom: sm6125: Move sdc2 pinctrl from seine-pdx201 to sm6125
[ Upstream commit
6990640a93ba4e76dd62ca3ea1082a7354db09d7 ]
Both the sdc2-on and sdc2-off pinctrl nodes are used by the
sdhci@4784000 node in sm6125.dtsi. Surprisingly sdc2-off is defined in
sm6125, yet its sdc2-on counterpart is only defined in board-specific DT
for the Sony Seine PDX201 board/device resulting in an "undefined label
&sdc2_state_on" error if sm6125.dtsi were included elsewhere.
This sm6125 base dtsi should not rely on externally defined labels; the
properties referencing it should then also be written externally.
Since the sdc2-on pin configuration is board-independent just like
sdc2-off, move it from seine-pdx201.dts into sm6125.dtsi.
The SDCard-detect pin (gpio98) is however board-specific, and remains as
an overwrite in seine-pdx201.dts for both the on and off state.
As a drive-by cleanup, reorder bias- and drive-strength properties.
Fixes:
cff4bbaf2a2d ("arm64: dts: qcom: Add support for SM6125")
Fixes:
82e1783890b7 ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220508100336.127176-1-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eric Auger [Thu, 30 Jun 2022 09:40:59 +0000 (11:40 +0200)]
ACPI: VIOT: Fix ACS setup
[ Upstream commit
3dcb861dbc6ab101838a1548b1efddd00ca3c3ec ]
Currently acpi_viot_init() gets called after the pci
device has been scanned and pci_enable_acs() has been called.
So pci_request_acs() fails to be taken into account leading
to wrong single iommu group topologies when dealing with
multi-function root ports for instance.
We cannot simply move the acpi_viot_init() earlier, similarly
as the IORT init because the VIOT parsing relies on the pci
scan. However we can detect VIOT is present earlier and in
such a case, request ACS. Introduce a new acpi_viot_early_init()
routine that allows to call pci_request_acs() before the scan.
While at it, guard the call to pci_request_acs() with #ifdef
CONFIG_PCI.
Fixes:
3cf485540e7b ("ACPI: Add driver for the VIOT table")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Jin Liu <jinl@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Len Baker [Sun, 15 Aug 2021 17:42:04 +0000 (19:42 +0200)]
drivers/iio: Remove all strcpy() uses
[ Upstream commit
d722f1e06fbc53eb369b39646945c1fa92068e74 ]
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. So, remove all the uses and add
devm_kstrdup() or devm_kasprintf() instead.
Also, modify the "for" loop conditions to clarify the access to the
st->orientation.rotation buffer.
This patch is an effort to clean up the proliferation of str*()
functions in the kernel and a previous step in the path to remove
the strcpy function from the kernel entirely [1].
[1] https://github.com/KSPP/linux/issues/88
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210815174204.126593-1-len.baker@gmx.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Shuai Xue [Sun, 27 Feb 2022 12:25:45 +0000 (20:25 +0800)]
ACPI: APEI: explicit init of HEST and GHES in apci_init()
[ Upstream commit
dc4e8c07e9e2f69387579c49caca26ba239f7270 ]
From commit
e147133a42cb ("ACPI / APEI: Make hest.c manage the estatus
memory pool") was merged, ghes_init() relies on acpi_hest_init() to manage
the estatus memory pool. On the other hand, ghes_init() relies on
sdei_init() to detect the SDEI version and (un)register events. The
dependencies are as follows:
ghes_init() => acpi_hest_init() => acpi_bus_init() => acpi_init()
ghes_init() => sdei_init()
HEST is not PCI-specific and initcall ordering is implicit and not
well-defined within a level.
Based on above, remove acpi_hest_init() from acpi_pci_root_init() and
convert ghes_init() and sdei_init() from initcalls to explicit calls in the
following order:
acpi_hest_init()
ghes_init()
sdei_init()
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sireesh Kodali [Thu, 26 May 2022 14:17:40 +0000 (19:47 +0530)]
arm64: dts: qcom: msm8916: Fix typo in pronto remoteproc node
[ Upstream commit
5458d6f2827cd30218570f266b8d238417461f2f ]
The smem-state properties for the pronto node were incorrectly labelled,
reading `qcom,state*` rather than `qcom,smem-state*`. Fix that, allowing
the stop state to be used.
Fixes:
88106096cbf8 ("ARM: dts: msm8916: Add and enable wcnss node")
Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220526141740.15834-3-sireeshkodali1@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
GONG, Ruiqi [Wed, 29 Jun 2022 06:04:23 +0000 (14:04 +0800)]
stack: Declare {randomize_,}kstack_offset to fix Sparse warnings
[ Upstream commit
375561bd6195a31bf4c109732bd538cb97a941f4 ]
Fix the following Sparse warnings that got noticed when the PPC-dev
patchwork was checking another patch (see the link below):
init/main.c:862:1: warning: symbol 'randomize_kstack_offset' was not declared. Should it be static?
init/main.c:864:1: warning: symbol 'kstack_offset' was not declared. Should it be static?
Which in fact are triggered on all architectures that have
HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET support (for instances x86, arm64
etc).
Link: https://lore.kernel.org/lkml/e7b0d68b-914d-7283-827c-101988923929@huawei.com/T/#m49b2d4490121445ce4bf7653500aba59eefcb67f
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Xiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes:
39218ff4c625 ("stack: Optionally randomize kernel stack offset each syscall")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220629060423.2515693-1-gongruiqi1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Fri, 1 Jul 2022 09:43:52 +0000 (17:43 +0800)]
bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
[ Upstream commit
54872fea6a5ac967ec2272aea525d1438ac6735a ]
In error case in hisi_lpc_acpi_probe() after calling platform_device_add(),
hisi_lpc_acpi_remove() can't release the failed 'pdev', so it will be leak,
call platform_device_put() to fix this problem.
I'v constructed this error case and tested this patch on D05 board.
Fixes:
99c0228d6ff1 ("HISI LPC: Re-Add ACPI child enumeration support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Krzysztof Kozlowski [Wed, 8 Jun 2022 11:27:02 +0000 (13:27 +0200)]
ARM: dts: qcom: pm8841: add required thermal-sensor-cells
[ Upstream commit
e2759fa0676c9a32bbddb9aff955b54bb35066ad ]
The PM8841 temperature sensor has to define thermal-sensor-cells.
Fixes:
dab8134ca072 ("ARM: dts: qcom: Add PM8841 functions device nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220608112702.80873-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Mon, 6 Jun 2022 06:42:52 +0000 (10:42 +0400)]
soc: qcom: aoss: Fix refcount leak in qmp_cooling_devices_register
[ Upstream commit
e6e0951414a314e7db3e9e24fd924b3e15515288 ]
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
When breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the child node.
Add missing of_node_put() to avoid refcount leak.
Fixes:
05589b30b21a ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220606064252.42595-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Thu, 2 Jun 2022 04:24:30 +0000 (08:24 +0400)]
soc: qcom: ocmem: Fix refcount leak in of_get_ocmem
[ Upstream commit
92a563fcf14b3093226fb36f12e9b5cf630c5a5d ]
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.
Fixes:
88c1e9404f1d ("soc: qcom: add OCMEM driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220602042430.1114-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luca Weiss [Sun, 22 May 2022 08:36:18 +0000 (10:36 +0200)]
ARM: dts: qcom-msm8974: fix irq type on blsp2_uart1
[ Upstream commit
ab1489017aa7a9f02e24bee73cf9ec8079cd3909 ]
IRQ_TYPE_NONE is invalid, so use the correct interrupt type.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Fixes:
b05f82b152c9 ("ARM: dts: qcom: msm8974: Add blsp2_uart7 for bluetooth on sirius")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220522083618.17894-1-luca@z3ntu.xyz
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Williams [Fri, 24 Jun 2022 23:05:26 +0000 (16:05 -0700)]
ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP
[ Upstream commit
b13a3e5fd40b7d1b394c5ecbb5eb301a4c38e7b2 ]
When a platform marks a memory range as "special purpose" it is not
onlined as System RAM by default. However, it is still suitable for
error injection. Add IORES_DESC_SOFT_RESERVED to einj_error_inject() as
a permissible memory type in the sanity checking of the arguments to
_EINJ.
Fixes:
262b45ae3ab4 ("x86/efi: EFI soft reservation to E820 enumeration")
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reported-by: Omar Avelar <omar.avelar@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stephan Gerhold [Thu, 23 Jun 2022 09:46:12 +0000 (11:46 +0200)]
regulator: qcom_smd: Fix pm8916_pldo range
[ Upstream commit
e8977917e116d1571dacb8e9864474551c1c12bd ]
The PM8916 device specification [1] documents a programmable range of
1.75V to 3.337V with 12.5mV steps for the PMOS LDOs in PM8916. This
range is also used when controlling the regulator directly using the
qcom_spmi-regulator driver ("ult_pldo" there).
However, for some reason the qcom_smd-regulator driver allows a much
larger range for the same hardware component. This could be simply a
typo, since the start of the range is essentially just missing a '1'.
In practice this does not cause any major problems, since the driver
just sends the actual voltage to the RPM firmware instead of making use
of the incorrect voltage selector. Still, having the wrong range there
is confusing and prevents the regulator core from validating requests
correctly.
[1]: https://developer.qualcomm.com/download/sd410/pm8916pm8916-1-power-management-ic-device-specification.pdf
Fixes:
57d6567680ed ("regulator: qcom-smd: Add PM8916 support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Link: https://lore.kernel.org/r/20220623094614.1410180-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Sun, 5 Jun 2022 08:28:07 +0000 (12:28 +0400)]
cpufreq: zynq: Fix refcount leak in zynq_get_revision
[ Upstream commit
d1ff2559cef0f6f8d97fba6337b28adb10689e16 ]
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes:
00f7dc636366 ("ARM: zynq: Add support for SOC_BUS")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220605082807.21526-1-linmq006@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Baryshkov [Sat, 21 May 2022 20:27:05 +0000 (23:27 +0300)]
arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf
[ Upstream commit
3a04cec9cba393abfe70fc62e523f381c9baec2e ]
Fix the device tree node in the &sdc2_state_on override. The sdm630 uses
'clk' rather than 'pinconf-clk'.
Fixes:
4c1d849ec047 ("arm64: dts: qcom: sdm630-xperia: Retire sdm630-sony-xperia-ganges.dtsi")
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-9-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Baryshkov [Sat, 21 May 2022 20:27:04 +0000 (23:27 +0300)]
arm64: dts: qcom: sdm630: fix gpu's interconnect path
[ Upstream commit
3cd1c4f41d64a40ea6bc4575ae28e37542123d77 ]
ICC path for the GPU incorrectly states <&gnoc 1 &bimc 5>, which is
a path from SLAVE_GNOC_BIMC to SLAVE_EBI. According to the downstream
kernel sources, the GPU uses MASTER_OXILI here, which is equivalent to
<&bimc 1 ...>.
While we are at it, use defined names instead of the numbers for this
interconnect path.
Fixes:
5cf69dcbec8b ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration")
Reported-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-8-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Baryshkov [Sat, 21 May 2022 20:27:01 +0000 (23:27 +0300)]
arm64: dts: qcom: sdm630: fix the qusb2phy ref clock
[ Upstream commit
924bbd8dd60e094344711c3526a5b308d71dc008 ]
According to the downstram DT file, the qusb2phy ref clock should be
GCC_RX0_USB2_CLKREF_CLK, not GCC_RX1_USB2_CLKREF_CLK.
Fixes:
c65a4ed2ea8b ("arm64: dts: qcom: sdm630: Add USB configuration")
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-5-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmitry Baryshkov [Sat, 21 May 2022 20:27:00 +0000 (23:27 +0300)]
arm64: dts: qcom: sdm630: disable GPU by default
[ Upstream commit
1c047919763b4548381d1ab3320af1df66ab83df ]
The SoC's device tree file disables gpucc and adreno's SMMU by default.
So let's disable the GPU too. Moreover it looks like SMMU might be not
usable without additional patches (which means that GPU is unusable
too). No board uses GPU at this moment.
Fixes:
5cf69dcbec8b ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration")
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-4-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Thu, 26 May 2022 07:37:24 +0000 (11:37 +0400)]
ARM: OMAP2+: Fix refcount leak in omap3xxx_prm_late_init
[ Upstream commit
942228fbf5d4901112178b93d41225be7c0dd9de ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes:
1e037794f7f0 ("ARM: OMAP3+: PRM: register interrupt information from DT")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <
20220526073724.21169-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Wed, 1 Jun 2022 04:48:58 +0000 (08:48 +0400)]
ARM: OMAP2+: Fix refcount leak in omapdss_init_of
[ Upstream commit
9705db1eff38d6b9114121f9e253746199b759c9 ]
omapdss_find_dss_of_node() calls of_find_compatible_node() to get device
node. of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in later error path and normal path.
Fixes:
e0c827aca0730 ("drm/omap: Populate DSS children in omapdss driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <
20220601044858.3352-1-linmq006@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Krzysztof Kozlowski [Sat, 7 May 2022 19:49:12 +0000 (21:49 +0200)]
ARM: dts: qcom: mdm9615: add missing PMIC GPIO reg
[ Upstream commit
dc590cdc31f636ea15658f1206c3e380a53fb78e ]
'reg' property is required in SSBI children:
qcom-mdm9615-wp8548-mangoh-green.dtb: gpio@150: 'reg' is a required property
Fixes:
2c5e596524e7 ("ARM: dts: Add MDM9615 dtsi")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Keith Busch [Fri, 10 Jun 2022 19:58:20 +0000 (12:58 -0700)]
block: fix infinite loop for invalid zone append
[ Upstream commit
b82d9fa257cb3725c49d94d2aeafc4677c34448a ]
Returning 0 early from __bio_iov_append_get_pages() for the
max_append_sectors warning just creates an infinite loop since 0 means
success, and the bio will never fill from the unadvancing iov_iter. We
could turn the return into an error value, but it will already be turned
into an error value later on, so just remove the warning. Clearly no one
ever hit it anyway.
Fixes:
0512a75b98f84 ("block: Introduce REQ_OP_ZONE_APPEND")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220610195830.3574005-2-kbusch@fb.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michael Walle [Mon, 4 Apr 2022 09:56:03 +0000 (11:56 +0200)]
soc: fsl: guts: machine variable might be unset
[ Upstream commit
ab3f045774f704c4e7b6a878102f4e9d4ae7bc74 ]
If both the model and the compatible properties are missing, then
machine will not be set. Initialize it with NULL.
Fixes:
34c1c21e94ac ("soc: fsl: fix section mismatch build warnings")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stephen Boyd [Tue, 17 May 2022 19:33:07 +0000 (12:33 -0700)]
arm64: dts: qcom: sc7180: Remove ipa_fw_mem node on trogdor
[ Upstream commit
e60414644cf3a703e10ed4429c15263095945ffe ]
We don't use this carveout on trogdor boards, and having it defined in
the sc7180 SoC file causes an overlap message to be printed at boot.
OF: reserved mem: OVERLAP DETECTED!
memory@
86000000 (0x0000000086000000--0x000000008ec00000) overlaps with memory@
8b700000 (0x000000008b700000--0x000000008b710000)
Delete the node in the trogdor dtsi file to fix the overlap problem and
remove the error message.
Cc: Alex Elder <elder@linaro.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Fixes:
310b266655a3 ("arm64: dts: qcom: sc7180: define ipa_fw_mem node")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220517193307.3034602-1-swboyd@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Peter Zijlstra [Fri, 17 Jun 2022 13:26:06 +0000 (15:26 +0200)]
locking/lockdep: Fix lockdep_init_map_*() confusion
[ Upstream commit
eae6d58d67d9739be5f7ae2dbead1d0ef6528243 ]
Commit
dfd5e3f5fe27 ("locking/lockdep: Mark local_lock_t") added yet
another lockdep_init_map_*() variant, but forgot to update all the
existing users of the most complicated version.
This could lead to a loss of lock_type and hence an incorrect report.
Given the relative rarity of both local_lock and these annotations,
this is unlikely to happen in practise, still, best fix things.
Fixes:
dfd5e3f5fe27 ("locking/lockdep: Mark local_lock_t")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YqyEDtoan20K0CVD@worktop.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
Alexandru Elisei [Fri, 17 Jun 2022 11:13:32 +0000 (12:13 +0100)]
arm64: cpufeature: Allow different PMU versions in ID_DFR0_EL1
[ Upstream commit
506506cad3947b942425b119ffa2b06715d5d804 ]
Commit
b20d1ba3cf4b ("arm64: cpufeature: allow for version discrepancy in
PMU implementations") made it possible to run Linux on a machine with PMUs
with different versions without tainting the kernel. The patch relaxed the
restriction only for the ID_AA64DFR0_EL1.PMUVer field, and missed doing the
same for ID_DFR0_EL1.PerfMon , which also reports the PMU version, but for
the AArch32 state.
For example, with Linux running on two clusters with different PMU
versions, the kernel is tainted when bringing up secondaries with the
following message:
[ 0.097027] smp: Bringing up secondary CPUs ...
[..]
[ 0.142805] Detected PIPT I-cache on CPU4
[ 0.142805] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_DFR0_EL1. Boot CPU: 0x00000004011088, CPU4: 0x00000005011088
[ 0.143555] CPU features: Unsupported CPU feature variation detected.
[ 0.143702] GICv3: CPU4: found redistributor 10000 region 0:0x000000002f180000
[ 0.143702] GICv3: CPU4: using allocated LPI pending table @0x00000008800d0000
[ 0.144888] CPU4: Booted secondary processor 0x0000010000 [0x410fd0f0]
The boot CPU implements FEAT_PMUv3p1 (ID_DFR0_EL1.PerfMon, bits 27:24, is
0b0100), but CPU4, part of the other cluster, implements FEAT_PMUv3p4
(ID_DFR0_EL1.PerfMon = 0b0101).
Treat the PerfMon field as FTR_NONSTRICT and FTR_EXACT to pass the sanity
check and to match how PMUVer is treated for the 64bit ID register.
Fixes:
b20d1ba3cf4b ("arm64: cpufeature: allow for version discrepancy in PMU implementations")
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20220617111332.203061-1-alexandru.elisei@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mark Rutland [Wed, 11 May 2022 13:17:33 +0000 (14:17 +0100)]
arm64: select TRACE_IRQFLAGS_NMI_SUPPORT
[ Upstream commit
3381da254fab37ba08c4b7c4f19b4ee28b1a27ec ]
Due to an oversight, on arm64 lockdep IRQ state tracking doesn't work as
intended in NMI context. This demonstrably results in bogus warnings
from lockdep, and in theory could mask a variety of issues.
On arm64, we've consistently tracked IRQ flag state for NMIs (and
saved/restored the state of the interrupted context) since commit:
f0cd5ac1e4c53cb6 ("arm64: entry: fix NMI {user, kernel}->kernel transitions")
That commit fixed most lockdep issues with NMI by virtue of the
save/restore of the lockdep state of the interrupted context. However,
for lockdep IRQ state tracking to consistently take effect in NMI
context it has been necessary to select TRACE_IRQFLAGS_NMI_SUPPORT since
commit:
ed00495333ccc80f ("locking/lockdep: Fix TRACE_IRQFLAGS vs. NMIs")
As arm64 does not select TRACE_IRQFLAGS_NMI_SUPPORT, this means that the
lockdep state can be stale in NMI context, and some uses of that state
can consume stale data.
When an NMI is taken arm64 entry code will call arm64_enter_nmi(). This
will enter NMI context via __nmi_enter() before calling
lockdep_hardirqs_off() to inform lockdep that IRQs have been masked.
Where TRACE_IRQFLAGS_NMI_SUPPORT is not selected, lockdep_hardirqs_off()
will not update lockdep state if called in NMI context. Thus if IRQs
were enabled in the original context, lockdep will continue to believe
that IRQs are enabled despite the call to lockdep_hardirqs_off().
However, the lockdep_assert_*() checks do take effect in NMI context,
and will consume the stale lockdep state. If an NMI is taken from a
context which had IRQs enabled, and during the handling of the NMI
something calls lockdep_assert_irqs_disabled(), this will result in a
spurious warning based upon the stale lockdep state.
This can be seen when using perf with GICv3 pseudo-NMIs. Within the perf
NMI handler we may attempt a uaccess to record the userspace callchain,
and is this faults the el1_abort() call in the nested context will call
exit_to_kernel_mode() when returning, which has a
lockdep_assert_irqs_disabled() assertion:
| # ./perf record -a -g sh
| ------------[ cut here ]------------
| WARNING: CPU: 0 PID: 164 at arch/arm64/kernel/entry-common.c:73 exit_to_kernel_mode+0x118/0x1ac
| Modules linked in:
| CPU: 0 PID: 164 Comm: perf Not tainted 5.18.0-rc5 #1
| Hardware name: linux,dummy-virt (DT)
| pstate:
004003c5 (nzcv DAIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : exit_to_kernel_mode+0x118/0x1ac
| lr : el1_abort+0x80/0xbc
| sp :
ffff8000080039f0
| pmr_save:
000000f0
| x29:
ffff8000080039f0 x28:
ffff6831054e4980 x27:
ffff683103adb400
| x26:
0000000000000000 x25:
0000000000000001 x24:
0000000000000001
| x23:
00000000804000c5 x22:
00000000000000c0 x21:
0000000000000001
| x20:
ffffbd51e635ec44 x19:
ffff800008003a60 x18:
0000000000000000
| x17:
ffffaadf98d23000 x16:
ffff800008004000 x15:
0000ffffd14f25c0
| x14:
0000000000000000 x13:
00000000000018eb x12:
0000000000000040
| x11:
000000000000001e x10:
000000002b820020 x9 :
0000000100110000
| x8 :
000000000045cac0 x7 :
0000ffffd14f25c0 x6 :
ffffbd51e639b000
| x5 :
00000000000003e5 x4 :
ffffbd51e58543b0 x3 :
0000000000000001
| x2 :
ffffaadf98d23000 x1 :
ffff6831054e4980 x0 :
0000000100110000
| Call trace:
| exit_to_kernel_mode+0x118/0x1ac
| el1_abort+0x80/0xbc
| el1h_64_sync_handler+0xa4/0xd0
| el1h_64_sync+0x74/0x78
| __arch_copy_from_user+0xa4/0x230
| get_perf_callchain+0x134/0x1e4
| perf_callchain+0x7c/0xa0
| perf_prepare_sample+0x414/0x660
| perf_event_output_forward+0x80/0x180
| __perf_event_overflow+0x70/0x13c
| perf_event_overflow+0x1c/0x30
| armv8pmu_handle_irq+0xe8/0x160
| armpmu_dispatch_irq+0x2c/0x70
| handle_percpu_devid_fasteoi_nmi+0x7c/0xbc
| generic_handle_domain_nmi+0x3c/0x60
| gic_handle_irq+0x1dc/0x310
| call_on_irq_stack+0x2c/0x54
| do_interrupt_handler+0x80/0x94
| el1_interrupt+0xb0/0xe4
| el1h_64_irq_handler+0x18/0x24
| el1h_64_irq+0x74/0x78
| lockdep_hardirqs_off+0x50/0x120
| trace_hardirqs_off+0x38/0x214
| _raw_spin_lock_irq+0x98/0xa0
| pipe_read+0x1f8/0x404
| new_sync_read+0x140/0x150
| vfs_read+0x190/0x1dc
| ksys_read+0xdc/0xfc
| __arm64_sys_read+0x20/0x30
| invoke_syscall+0x48/0x114
| el0_svc_common.constprop.0+0x158/0x17c
| do_el0_svc+0x28/0x90
| el0_svc+0x60/0x150
| el0t_64_sync_handler+0xa4/0x130
| el0t_64_sync+0x19c/0x1a0
| irq event stamp: 483
| hardirqs last enabled at (483): [<
ffffbd51e636aa24>] _raw_spin_unlock_irqrestore+0xa4/0xb0
| hardirqs last disabled at (482): [<
ffffbd51e636acd0>] _raw_spin_lock_irqsave+0xb0/0xb4
| softirqs last enabled at (468): [<
ffffbd51e5216f58>] put_cpu_fpsimd_context+0x28/0x70
| softirqs last disabled at (466): [<
ffffbd51e5216ed4>] get_cpu_fpsimd_context+0x0/0x5c
| ---[ end trace
0000000000000000 ]---
Note that as lockdep_assert_irqs_disabled() uses WARN_ON_ONCE(), and
this uses a BRK, the warning is logged with the real PSTATE at the time
of the warning, which clearly has DAIF.I set, meaning IRQs (and
pseudo-NMIs) were definitely masked and the warning is spurious.
Fix this by selecting TRACE_IRQFLAGS_NMI_SUPPORT such that the existing
entry tracking takes effect, as we had originally intended when the
arm64 entry code was fixed for transitions to/from NMI.
Arguably the lockdep_assert_*() functions should have the same NMI
checks as the rest of the code to prevent spurious warnings when
TRACE_IRQFLAGS_NMI_SUPPORT is not selected, but the real fix for any
architecture is to explicitly handle the transitions to/from NMI in the
entry code.
Fixes:
f0cd5ac1e4c5 ("arm64: entry: fix NMI {user, kernel}->kernel transitions")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20220511131733.4074499-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nícolas F. R. A. Prado [Fri, 17 Jun 2022 23:31:50 +0000 (19:31 -0400)]
arm64: dts: mt8192: Fix idle-states entry-method
[ Upstream commit
2e599740f7e423ee89fb027896cb2635dd43784f ]
The entry-method property of the idle-states node should be "psci" as
described in the idle-states binding, since this is already the value of
enable-method in the CPU nodes. Fix it to get rid of a dtbs_check
warning.
Fixes:
9260918d3a4f ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-3-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nícolas F. R. A. Prado [Fri, 17 Jun 2022 23:31:49 +0000 (19:31 -0400)]
arm64: dts: mt8192: Fix idle-states nodes naming scheme
[ Upstream commit
399e23ad51caaf62400a531c9268ad3c453c3d76 ]
Tweak the name of the idle-states subnodes so that they follow the
binding pattern, getting rid of dtbs_check warnings.
Only the usage of "-" in the name was necessary, but "off" was also
exchanged for "sleep" since that seems to be a more common wording in
other dts files.
Fixes:
9260918d3a4f ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Krzysztof Kozlowski [Sun, 29 May 2022 10:49:27 +0000 (12:49 +0200)]
ARM: dts: ast2600-evb-a1: fix board compatible
[ Upstream commit
33c39140cc298e0d4e36083cb9a665a837773a60 ]
The AST2600 EVB A1 board should have dedicated compatible.
Fixes:
a72955180372 ("ARM: dts: aspeed: ast2600evb: Add dts file for A1 and A0")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220529104928.79636-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Krzysztof Kozlowski [Sun, 29 May 2022 10:49:26 +0000 (12:49 +0200)]
ARM: dts: ast2600-evb: fix board compatible
[ Upstream commit
aa5e06208500a0db41473caebdee5a2e81d5a277 ]
The AST2600 EVB board should have dedicated compatible.
Fixes:
2ca5646b5c2f ("ARM: dts: aspeed: Add AST2600 and EVB")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220529104928.79636-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Krzysztof Kozlowski [Sun, 29 May 2022 10:49:25 +0000 (12:49 +0200)]
ARM: dts: ast2500-evb: fix board compatible
[ Upstream commit
30b276fca5c0644f3cb17bceb1bd6a626c670184 ]
The AST2500 EVB board should have dedicated compatible.
Fixes:
02440622656d ("arm/dst: Add Aspeed ast2500 device tree")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220529104928.79636-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johan Hovold [Mon, 20 Jun 2022 14:07:23 +0000 (16:07 +0200)]
x86/pmem: Fix platform-device leak in error path
[ Upstream commit
229e73d46994f15314f58b2d39bf952111d89193 ]
Make sure to free the platform device in the unlikely event that
registration fails.
Fixes:
7a67832c7e44 ("libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220620140723.9810-1-johan@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Geert Uytterhoeven [Wed, 15 Jun 2022 14:04:26 +0000 (16:04 +0200)]
arm64: dts: renesas: Fix thermal-sensors on single-zone sensors
[ Upstream commit
62e8a53431145e06e503b71625a34eaa87b72b2c ]
"make dtbs_check":
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[74], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[79], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[82], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-mipi-2.1.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[87], [0]] is too long
arch/arm64/boot/dts/renesas/r8a77990-ebisu.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[105], [0]] is too long
From schema: Documentation/devicetree/bindings/thermal/thermal-zones.yaml
Indeed, the thermal sensors on R-Car E3 and RZ/G2E support only a single
zone, hence #thermal-sensor-cells = <0>.
Fix this by dropping the bogus zero cell from the thermal sensor
specifiers.
Fixes:
8fa7d18f9ee2dc20 ("arm64: dts: renesas: r8a77990: Create thermal zone to support IPA")
Fixes:
8438bfda9d768157 ("arm64: dts: renesas: r8a774c0: Create thermal zone to support IPA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/28b812fdd1fc3698311fac984ab8b91d3d655c1c.1655301684.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
Liang He [Thu, 16 Jun 2022 14:49:15 +0000 (22:49 +0800)]
soc: amlogic: Fix refcount leak in meson-secure-pwrc.c
[ Upstream commit
d18529a4c12f66d83daac78045ea54063bd43257 ]
In meson_secure_pwrc_probe(), there is a refcount leak in one fail
path.
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes:
b3dde5013e13 ("soc: amlogic: Add support for Secure power domains controller")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220616144915.3988071-1-windhl@126.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Puranjay Mohan [Wed, 11 Aug 2021 07:30:26 +0000 (13:00 +0530)]
dt-bindings: iio: accel: Add DT binding doc for ADXL355
[ Upstream commit
bf43a71a0a7f396434f6460b46e33eb00752f78d ]
Add devicetree binding document for ADXL355, a 3-Axis MEMS Accelerometer.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210811073027.124619-2-puranjay12@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiang Chen [Tue, 24 Aug 2021 10:00:56 +0000 (18:00 +0800)]
scsi: hisi_sas: Use managed PCI functions
[ Upstream commit
4f6094f1663e2ed26a940f1842cdaa15c1dd649a ]
Use managed PCI functions such as pcim_enable_device() and
pcim_iomap_regions() to simplify exception handling code.
Link: https://lore.kernel.org/r/1629799260-120116-2-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Geert Uytterhoeven [Wed, 8 Jun 2022 13:51:35 +0000 (15:51 +0200)]
soc: renesas: r8a779a0-sysc: Fix A2DP1 and A2CV[2357] PDR values
[ Upstream commit
bccceabb92ce8eb78bbf2de08308e2cc2761a2e5 ]
The PDR values for the A2DP1 and A2CV[2357] power areas on R-Car V3U are
incorrect (copied-and-pasted from A2DP0 and A2CV[0146]).
Fix them.
Reported-by: Renesas Vietnam via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes:
1b4298f000064cc2 ("soc: renesas: r8a779a0-sysc: Add r8a779a0 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87bc2e70ba4082970cf8c65871beae4be3503189.1654696188.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
Marcel Ziswiler [Mon, 16 May 2022 13:47:23 +0000 (15:47 +0200)]
ARM: dts: imx7d-colibri-emmc: add cpu1 supply
[ Upstream commit
ba28db60d34271e8a3cf4d7158d71607e8b1e57f ]
Each cpu-core is supposed to list its supply separately, add supply for
cpu1.
Fixes:
2d7401f8632f ("ARM: dts: imx7d: Add cpu1 supply")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Guilherme G. Piccoli [Tue, 7 Jun 2022 22:24:58 +0000 (19:24 -0300)]
ACPI: processor/idle: Annotate more functions to live in cpuidle section
[ Upstream commit
409dfdcaffb266acfc1f33529a26b1443c9332d4 ]
Commit
6727ad9e206c ("nmi_backtrace: generate one-line reports for idle cpus")
introduced a new text section called cpuidle; with that, we have a mechanism
to add idling functions in such section and skip them from nmi_backtrace
output, since they're useless and potentially flooding for such report.
Happens that inlining might cause some real idle functions to end-up
outside of such section; this is currently the case of ACPI processor_idle
driver; the functions acpi_idle_enter_* do inline acpi_idle_do_entry(),
hence they stay out of the cpuidle section.
Fix that by marking such functions to also live in the cpuidle section.
Fixes:
6727ad9e206c ("nmi_backtrace: generate one-line reports for idle cpus")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Thu, 26 May 2022 08:13:25 +0000 (12:13 +0400)]
ARM: bcm: Fix refcount leak in bcm_kona_smc_init
[ Upstream commit
cb23389a2458c2e4bfd6c86a513cbbe1c4d35e76 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes:
b8eb35fd594a ("ARM: bcm281xx: Add L2 cache enable code")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe JAILLET [Sun, 29 May 2022 06:31:53 +0000 (08:31 +0200)]
spi: spi-altera-dfl: Fix an error handling path
[ Upstream commit
8e3ca32f46994e74b7f43c57731150b2aedb2630 ]
The spi_alloc_master() call is not undone in all error handling paths.
Moreover, there is no .remove function to release the allocated memory.
In order to fix both this issues, switch to devm_spi_alloc_master().
This allows further simplification of the probe.
Fixes:
ba2fc167e944 ("spi: altera: Add DFL bus driver for Altera API Controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0607bb59f4073f86abe5c585d35245aef0b045c6.1653805901.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Geert Uytterhoeven [Wed, 11 May 2022 10:14:06 +0000 (12:14 +0200)]
arm64: dts: renesas: beacon: Fix regulator node names
[ Upstream commit
7512af9f78dedea7e04225f665dad6750df7d095 ]
Currently there are two nodes named "regulator_camera". This causes the
former to be overwritten by the latter.
Fix this by renaming them to unique names, using the preferred hyphen
instead of an underscore.
While at it, update the name of the audio regulator (which was added in
the same commit) to use a hyphen.
Fixes:
a1d8a344f1ca0709 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a9ac82bdf108162487289d091c53a9b3de393f13.1652263918.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
Miaoqian Lin [Tue, 24 May 2022 06:57:29 +0000 (10:57 +0400)]
meson-mx-socinfo: Fix refcount leak in meson_mx_socinfo_init
[ Upstream commit
a2106f38077e78afcb4bf98fdda3e162118cfb3d ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes:
5e68c0fc8df8 ("soc: amlogic: Add Meson6/Meson8/Meson8b/Meson8m2 SoC Information driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220524065729.33689-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Russell King (Oracle) [Tue, 26 Jul 2022 22:51:48 +0000 (23:51 +0100)]
ARM: findbit: fix overflowing offset
[ Upstream commit
ec85bd369fd2bfaed6f45dd678706429d4f75b48 ]
When offset is larger than the size of the bit array, we should not
attempt to access the array as we can perform an access beyond the
end of the array. Fix this by changing the pre-condition.
Using "cmp r2, r1; bhs ..." covers us for the size == 0 case, since
this will always take the branch when r1 is zero, irrespective of
the value of r2. This means we can fix this bug without adding any
additional code!
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Biju Das [Thu, 21 Jul 2022 14:34:49 +0000 (15:34 +0100)]
spi: spi-rspi: Fix PIO fallback on RZ platforms
[ Upstream commit
b620aa3a7be346f04ae7789b165937615c6ee8d3 ]
RSPI IP on RZ/{A, G2L} SoC's has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked.
PIO fallback does not work as interrupt signal is disabled.
This patch fixes this issue by re-enabling the interrupts by
calling dmaengine_synchronize().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220721143449.879257-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michael Ellerman [Mon, 18 Jul 2022 13:44:18 +0000 (23:44 +1000)]
powerpc/64s: Disable stack variable initialisation for prom_init
[ Upstream commit
be640317a1d0b9cf42fedb2debc2887a7cfa38de ]
With GCC 12 allmodconfig prom_init fails to build:
Error: External symbol 'memset' referenced from prom_init.c
make[2]: *** [arch/powerpc/kernel/Makefile:204: arch/powerpc/kernel/prom_init_check] Error 1
The allmodconfig build enables KASAN, so all calls to memset in
prom_init should be converted to __memset by the #ifdefs in
asm/string.h, because prom_init must use the non-KASAN instrumented
versions.
The build failure happens because there's a call to memset that hasn't
been caught by the pre-processor and converted to __memset. Typically
that's because it's a memset generated by the compiler itself, and that
is the case here.
With GCC 12, allmodconfig enables CONFIG_INIT_STACK_ALL_PATTERN, which
causes the compiler to emit memset calls to initialise on-stack
variables with a pattern.
Because prom_init is non-user-facing boot-time only code, as a
workaround just disable stack variable initialisation to unbreak the
build.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220718134418.354114-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / platform / kernel / linux-rpi.git / log