Andreas Färber [Sun, 3 Jun 2018 05:23:58 +0000 (07:23 +0200)]
rockchip: make_fit_atf.py depends on u-boot
u-boot.itb depends on u-boot-nodtb.bin, which in turn depends on u-boot.
u-boot.its from Rockchip make_fit_atf.py (used by {evb,firefly}-rk3399)
wants to read u-boot but is lacking this dependency, so that u-boot.itb
cannot be built in one go. Detect its use and add the missing dependency.
Reported-by: Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Janine Hagemann [Tue, 28 Aug 2018 06:25:05 +0000 (08:25 +0200)]
net: gmac_rockchip: Add handling for RGMII_ID/RXID/TXID
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.
Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.
Based on commit
eaf70ad14cbb ("net: stmmac: dwmac-rk: Add
handling for RGMII_ID/RXID/TXID") for mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Janine Hagemann [Tue, 28 Aug 2018 06:25:04 +0000 (08:25 +0200)]
net: gmac_rockchip: Fix a register write in rk3328_gmac_set_to_rgmii
We have to use RK3328_RXCLK_DLY_ENA_GMAC_ENABLE instead of
RK3328_RXCLK_DLY_ENA_GMAC_MASK in rk3328_gmac_set_to_rgmii()
to enable the RX delay.
The MASK was used in a wrong way.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Reviewed-by: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mian Yousaf Kaukab [Fri, 8 Jun 2018 08:47:10 +0000 (10:47 +0200)]
rockchip: make_fit_atf: make python3 compatible
Make script python3 compatible. No functional changes intended.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Mian Yousaf Kaukab [Fri, 8 Jun 2018 08:47:09 +0000 (10:47 +0200)]
rockchip: make_fit_atf: use elf entry point
make_fit_atf.py uses physical address of first segment as the
entry point to bl31. It is incorrect and causes following abort
when bl31_entry() is called:
U-Boot SPL board initTrying to boot from MMC1
"Synchronous Abort" handler, esr 0x02000000
elr:
0000000000000000 lr :
00000000ff8c7e8c
x 0:
00000000ff8e0000 x 1:
0000000000000000
x 2:
0000000000000000 x 3:
00000000ff8e0180
x 4:
0000000000000000 x 5:
0000000000000000
x 6:
0000000000000030 x 7:
00000000ff8e0188
x 8:
00000000000001e0 x 9:
0000000000000000
x10:
000000000007fcdc x11:
00000000002881b8
x12:
00000000000001a2 x13:
0000000000000198
x14:
000000000007fdcc x15:
00000000002881b8
x16:
00000000003c0724 x17:
00000000003c0718
x18:
000000000007fe80 x19:
00000000ff8e0000
x20:
0000000000200000 x21:
00000000ff8e0000
x22:
0000000000000000 x23:
000000000007fe30
x24:
00000000ff8d1c3c x25:
00000000ff8d5000
x26:
00000000deadbeef x27:
00000000000004a0
x28:
000000000000009c x29:
000000000007fd90
Fix it by using the entry point from the elf header.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 23 Aug 2018 09:18:00 +0000 (17:18 +0800)]
rockchip: add fit source file for pack itb with op-tee
We package U-Boot and OP-TEE into one itb file for SPL,
so that we can support OP-TEE in SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 23 Aug 2018 09:17:59 +0000 (17:17 +0800)]
spl: add support to booting with OP-TEE
OP-TEE is an open source trusted OS, in armv7, its loading and
running are like this:
loading:
- SPL load both OP-TEE and U-Boot
running:
- SPL run into OP-TEE in secure mode;
- OP-TEE run into U-Boot in non-secure mode;
To make code simple, it would be fine to use IH_OS_TEE for the
os tyle in TPL(just like IH_OS_LINUX is using both in SPL and U-Boot).
Here is the diagram for SPL loading OP-TEE,
IH_OS_TEE:(make u-boot.itb for SPL)
Non-Secure Secure
BootROM
|
v
SPL
|
v
--------- OP-TEE
|
v
U-Boot
|
V
Linux
For other two king of OP-TEE loading/booting, see commit message:
45b55712d4 image: Add IH_OS_TEE for TEE chain-load boot
More detail:
https://github.com/OP-TEE/optee_os
and search for 'boot arguments' for detail entry parameter in:
core/arch/arm/kernel/generic_entry_a32.S
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 23 Aug 2018 03:01:08 +0000 (11:01 +0800)]
rockchip: make_fit_atf: fix warning unit_address_vs_reg
Patch fix warning:
/builddir/BUILD/u-boot-2018.05-rc2/"arch/arm/mach-rockchip/make_fit_atf.py" \
arch/arm/dts/rk3399-firefly.dtb > u-boot.its
./tools/mkimage -f u-boot.its -E u-boot.itb >/dev/null && cat
/dev/null
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@2 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@3 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node
/configurations/config@1 has a unit name, but no reg property
make[1]: Leaving directory
'/builddir/BUILD/u-boot-2018.05-rc2/builds/firefly-rk3399'
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Wed, 3 Oct 2018 16:09:19 +0000 (12:09 -0400)]
Merge tag 'rockchip-for-v2018.11' of git://git.denx.de/u-boot-rockchip
Rockchip changes for 2018.11
Tom Rini [Wed, 3 Oct 2018 12:09:53 +0000 (08:09 -0400)]
Merge git://git.denx.de/u-boot-riscv
- QEMU support
Tom Rini [Wed, 3 Oct 2018 12:09:22 +0000 (08:09 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Add support for the Arm's Versatile Express I2C controller.
Heinrich Schuchardt [Mon, 6 Aug 2018 17:15:38 +0000 (19:15 +0200)]
riscv: allow native compilation
If environment variable CROSS_COMPILE is not set, this indicates native
compilation. In this case we should not set an arbitrary value which is
not applicable for 64bit anyway.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Rick Chen [Wed, 3 Oct 2018 05:59:03 +0000 (13:59 +0800)]
riscv: cosmetic: Reword do_reset() printf message.
The Sentence "reset unsupported yet" is not
grammatically correct and should say
"reset not supported yet" instead.
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Rick Chen <rick@andestech.com>
Bin Meng [Wed, 26 Sep 2018 13:55:22 +0000 (06:55 -0700)]
riscv: Move do_reset() to a common place
We don't have a reset method on any RISC-V board yet. Instead of
adding the same 'unsupported' message for each CPU variant it might
make more sense to add a generic do_reset function for all CPU
variants to lib/, similar to the one for ARM (arch/arm/lib/reset.c).
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:21 +0000 (06:55 -0700)]
riscv: Add QEMU virt board support
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:20 +0000 (06:55 -0700)]
riscv: kconfig: Imply DM support for some common drivers
This implies DM support for some common drivers that are used on
RISC-V.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:19 +0000 (06:55 -0700)]
riscv: kconfig: Select DM and OF_CONTROL
RISC-V is a pretty new architecture and should support DM and
OF_CONTROL by default.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:18 +0000 (06:55 -0700)]
riscv: ae350: Clean up mixed tabs and spaces in the dts
There are quite a lot of mixed tabs and spaces in the ae350.dts.
Clean them up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:17 +0000 (06:55 -0700)]
riscv: Make start.S available for all targets
Currently start.S is inside arch/riscv/cpu/ax25/, but it can be
common for all RISC-V targets.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:16 +0000 (06:55 -0700)]
riscv: bootm: Pass mhartid CSR value to kernel
So far this is hardcoded to zero, and we should read the value from
mhartid CSR and pass it to Linux kernel.
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Wed, 26 Sep 2018 13:55:15 +0000 (06:55 -0700)]
riscv: Remove CSR read/write defines in encoding.h
There is no reason to keep two versions of CSR read/write defines
in encoding.h. We already have one set of defines in csr.h, which
is from Linux kernel, and let's drop the one in encoding.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Wed, 26 Sep 2018 13:55:14 +0000 (06:55 -0700)]
riscv: Add a helper routine to print CPU information
This adds a helper routine to print CPU information. Currently
it prints all the instruction set extensions that the processor
core supports.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:13 +0000 (06:55 -0700)]
riscv: Explicitly pass -march and -mabi to the compiler
At present the compiler flag against which architecture and abi
variant the riscv image is built for is not explicitly indicated
which means the default compiler configuration is used. But this
does not work if we want to build a different target (eg: 32-bit
riscv images using a toolchain configured for 64-bit riscv).
Fix this by explicitly passing -march and -mabi to the compiler.
Since generically we don't use floating point in U-Boot, specify
the RV[32|64]IMA ISA and software floating ABI.
This also fix some alignment coding style issues.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:12 +0000 (06:55 -0700)]
riscv: Fix coding style issues in the linker script
There are several coding style issues in the linker script. Fix them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:11 +0000 (06:55 -0700)]
riscv: Move the linker script to the CPU root directory
The linker script can be shared by all RISC-V targets. Move it to
a common place.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:10 +0000 (06:55 -0700)]
riscv: cmd: bdinfo: Print the relocation address
Add printing of U-Boot relocation address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:09 +0000 (06:55 -0700)]
riscv: Remove mach type
Since the mach_id is not used by RISC-V, remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:08 +0000 (06:55 -0700)]
riscv: bootm: Correct the 1st kernel argument to hart id
The first argument of Linux kernel is the risc-v core hart id,
from which the kernel is booted from. It is not the mach_id,
which seems to be copied from arm.
While we are here, this also changes the Linux kernel entry
parameters' type to support both 32-bit and 64-bit.
Note the hart id is hardcoded to zero for now, and we should
change to fill in it with the value read from mhartid CSR of
the hart which this routine is currently running on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Wed, 26 Sep 2018 13:55:07 +0000 (06:55 -0700)]
riscv: Remove setup.h
This was copied from ARM, and does not apply to RISC-V. While we
are here, bootm.h is eventually removed as its content is only
the inclusion of setup.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 26 Sep 2018 13:55:06 +0000 (06:55 -0700)]
riscv: kconfig: Normalize architecture name spelling
It's RISC-V that is the official name, not RISCV.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Liviu Dudau [Fri, 28 Sep 2018 12:46:48 +0000 (13:46 +0100)]
i2c: Add support for the Arm's Versatile Express I2C controller.
The Arm Versatile Express I2C controller is a simple register-based
controller that uses a register to control the state of the SCL and
SDA lines. Add support for it.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Tue, 2 Oct 2018 17:02:22 +0000 (13:02 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 25 Aug 2018 17:34:24 +0000 (19:34 +0200)]
spi: sh_qspi: Add DM support to SH QSPI driver
Add DM support to the SH QSPI driver while retaining non-DM support.
The later is required as this driver is used in SPL which has a size
limitation of 16 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
[jagan: use proper commit head]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Ashish Kumar [Fri, 7 Sep 2018 04:19:34 +0000 (09:49 +0530)]
driver/spi: fsl_qspi: Remove non-DM stuff
Convert fsl_qspi.c to complete DM mode.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Tested-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Tested-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Ley Foon Tan [Fri, 7 Sep 2018 06:25:29 +0000 (14:25 +0800)]
spi: designware_spi: Add reset ctrl to driver
Add code to reset all reset signals as in SPI DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Release reset when _remove().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:30 +0000 (12:58 +0200)]
cmd: mtdparts: describe as legacy
The 'mtdparts' command is not needed anymore. While the environment
variable is still valid (and useful, along with the 'mtdids' one), the
command has been replaced by 'mtd' which is much more close to the MTD
stack and do not add its own specific glue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:29 +0000 (12:58 +0200)]
cmd: ubi: clean the partition handling
UBI should not mess with MTD partitions, now that the partitions are
handled in a clean way, clean the ubi command and avoid using this
uneeded extra-glue to reference the devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:28 +0000 (12:58 +0200)]
cmd: mtd: add 'mtd' command
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:27 +0000 (12:58 +0200)]
mtd: mtdpart: implement proper partition handling
Instead of collecting partitions in a flat list, create a hierarchy
within the mtd_info structure: use a partitions list to keep track of
the partitions of an MTD device (which might be itself a partition of
another MTD device), a pointer to the parent device (NULL when the MTD
device is the root one, not a partition).
By also saving directly in mtd_info the offset of the partition, we
can get rid of the mtd_part structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:26 +0000 (12:58 +0200)]
mtd: uboot: search for an equivalent MTD name with the mtdids
Using an MTD device (resp. partition) name in mtdparts is simple and
straightforward. However, for a long time already, another name was
given in mtdparts to indicate a device (resp. partition) so the
"mtdids" environment variable was created to do the match.
Let's create a function that, from an MTD device (resp. partition)
name, search for the equivalent name in the "mtdparts" environment
variable thanks to the "mtdids" string.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:25 +0000 (12:58 +0200)]
mtd: mtdpart: add a generic mtdparts-like parser
The current parser is very specific to U-Boot mtdparts implementation.
It does not use MTD structures like mtd_info and mtd_partition. Copy
and adapt the current parser in drivers/mtd/mtd-uclass.c (to not break
the current use of mtdparts.c itself) and write some kind of a wrapper
around the current implementation to allow other commands to benefit
from this parsing in a user-friendly way.
This new function will allocate an mtd_partition array for each
successful call. This array must be freed after use by the caller.
The given 'mtdparts' buffer pointer will be moved forward to the next
MTD device (if any, it will point towards a '\0' character otherwise).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:24 +0000 (12:58 +0200)]
mtd: uclass: add probe function
The user might want to trigger the probe of any MTD device, export these
functions so they can be called from a command source file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Miquel Raynal [Sat, 29 Sep 2018 10:58:23 +0000 (12:58 +0200)]
dm: drop unused helper in MTD header
include/mtd.h might be included by files even if CONFIG_DM is not
enabled. In this case, the call to dev_get_uclass_priv() would trigger
a build error. Because this helper has no user, let's drop it off.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Heiko Stuebner [Fri, 21 Sep 2018 08:59:48 +0000 (10:59 +0200)]
rockchip: rk3188: explicitly set vcc_sd0 pin to gpio on rk3188-radxarock
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
[picked from the identical linux patch
https://patchwork.kernel.org/patch/
10609253/]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Heiko Stuebner [Fri, 21 Sep 2018 08:59:47 +0000 (10:59 +0200)]
rockchip: rk3188: add u-boot-specific mmc properties
The dwmmc controllers on rk3188 do not have idma support, so need to
use the fifo-mode and it my tests they became confused and stopped
working if the frequency was to high.
While I only tested in somewhat bigger steps, 32MHz for example
hung the controller, while reducing it to 16MHz worked just fine
and is reasonably fast to load a kernel from mmc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Heiko Stuebner [Fri, 21 Sep 2018 08:59:46 +0000 (10:59 +0200)]
rockchip: dwmmc: add rk2928-dw-mshc compatible
The rk3188 works nicely with the rockchip mmc driver, so we just need
to add the different compatible for it - as used in the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Heiko Stuebner [Fri, 21 Sep 2018 08:59:45 +0000 (10:59 +0200)]
mmc: dw_mmc: check fifo status with a timeout in fifo mode
While trying to enable the dw_mmc on rk3188 I managed to confuse
and hang the dw_mmc controller into not delivering further data.
The fifo state never became ready and the driver was iterating in
the while loop reading 0-byte packets forever.
So inspired by how other implementations handle this, check the fifo-
state beforhand and add a timeout to catch any glaring fifo issues
without hanging uboot altogether.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Tue, 2 Oct 2018 00:32:03 +0000 (20:32 -0400)]
Prepare v2018.11-rc1
Signed-off-by: Tom Rini <trini@konsulko.com>
Eugen Hristev [Mon, 1 Oct 2018 14:31:53 +0000 (17:31 +0300)]
MAINTAINERS: at91: update entry for at91 boards
Updated the maintainership for the at91 boards.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tom Rini [Sun, 30 Sep 2018 22:16:51 +0000 (18:16 -0400)]
Merge git://git.denx.de/u-boot-dm
Tom Rini [Sun, 30 Sep 2018 14:24:45 +0000 (10:24 -0400)]
MAINTAINERS: Update some entries for missed boards
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 22 Sep 2018 02:13:35 +0000 (04:13 +0200)]
fs: btrfs: Fix cache alignment bugs
The btrfs implementation passes cache-unaligned buffers into the
block layer, which triggers cache alignment problems down in the
block device drivers. Align the buffers to prevent this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Behun <marek.behun@nic.cz>
Ramon Fried [Fri, 21 Sep 2018 10:35:56 +0000 (13:35 +0300)]
usb:ci_udc: don't overwrite configuration on pullup
change writel to writebits32 in ci_pullup() in order
to keep phy configuration in tact.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:55 +0000 (13:35 +0300)]
db410c: automatically launch fastboot
If during boot the key-vol-down press is detected
we'll fall back to fastboot.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:54 +0000 (13:35 +0300)]
DB410c: Enable fastboot support
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:53 +0000 (13:35 +0300)]
usb: ehci-msm: Add init_after_reset for CI_UDC
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:52 +0000 (13:35 +0300)]
usb:ci_udc: Introduce init_after_reset phy function
MSM variant of Chipidea must reinitalize the phy
after controller reset.
Introduce ci_init_after_reset() weak function that
can be used to achieve the above init.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:51 +0000 (13:35 +0300)]
ehci: msm: use init_type in probe
Change ehci_usb_probe() function to initialize the
USB according to the init_type provided.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:50 +0000 (13:35 +0300)]
ehci: msm: switch to generic PHY uclass
All the underlying USB PHY was handled in the ehci driver.
Use the generic phy API instead.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:49 +0000 (13:35 +0300)]
configs: db410c: Enable USB PHY
Enable USB PHY driver.
Also fixed the alphabetically ordering of the config.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:48 +0000 (13:35 +0300)]
dts: db410c: Add bindings for MSM USB phy
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:47 +0000 (13:35 +0300)]
phy: db410c: Add MSM USB PHY driver
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:46 +0000 (13:35 +0300)]
db410c: serial# env using msm board serial
The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:45 +0000 (13:35 +0300)]
dts: db410c: add alias for USB
Alias is required so req-seq will be filled.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:44 +0000 (13:35 +0300)]
ehci: msm: Add missing platdata
platdata_auto_alloc_size was not initialized in structure.
Caused null pointer dereference when configuring device as
gadget.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Ramon Fried [Fri, 21 Sep 2018 10:35:43 +0000 (13:35 +0300)]
ehci: Replace board_prepare_usb with board_usb_init
Use standard board_usb_init() instead of the specific board_prepare_usb.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Patrice Chotard [Thu, 20 Sep 2018 13:14:15 +0000 (15:14 +0200)]
serial: serial_stm32: Enable uart FIFO for STM32F7xx SoCs
Since commit
7b3b74d32127 ("serial: serial_stm32: Enable overrun")
on STM32F7xx based boards, the first lines of serial output are
missing during boot (we no more see the U-Boot release version,
board model and DRAM size).
By enabling the uart FIFO on STM32F7, the complete U-boot log
can be sent correctly.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Neil Stainton [Wed, 19 Sep 2018 09:38:07 +0000 (10:38 +0100)]
u-boot: align cache flushes in load_elf_image_shdr to line boundaries
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace]
Signed-off-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Wed, 19 Sep 2018 02:35:57 +0000 (11:35 +0900)]
kbuild: fix # escaping in appending U-Boot own DT
The escape sequence '\#' does not work for the latest GNU Make from
the git tree.
Replace it with $(pound) as Linux did.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Rasmus Villemoes [Wed, 19 Sep 2018 02:35:56 +0000 (11:35 +0900)]
Kbuild: fix # escaping in .cmd files for future Make
[ commit
9564a8cf422d7b58f6e857e3546d346fa970191e in Linux ]
I tried building using a freshly built Make (4.2.1-69-g8a731d1), but
already the objtool build broke with
orc_dump.c: In function ‘orc_dump’:
orc_dump.c:106:2: error: ‘elf_getshnum’ is deprecated [-Werror=deprecated-declarations]
if (elf_getshdrnum(elf, &nr_sections)) {
Turns out that with that new Make, the backslash was not removed, so cpp
didn't see a #include directive, grep found nothing, and
-DLIBELF_USE_DEPRECATED was wrongly put in CFLAGS.
Now, that new Make behaviour is documented in their NEWS file:
* WARNING: Backward-incompatibility!
Number signs (#) appearing inside a macro reference or function invocation
no longer introduce comments and should not be escaped with backslashes:
thus a call such as:
foo := $(shell echo '#')
is legal. Previously the number sign needed to be escaped, for example:
foo := $(shell echo '\#')
Now this latter will resolve to "\#". If you want to write makefiles
portable to both versions, assign the number sign to a variable:
C := \#
foo := $(shell echo '$C')
This was claimed to be fixed in 3.81, but wasn't, for some reason.
To detect this change search for 'nocomment' in the .FEATURES variable.
This also fixes up the two make-cmd instances to replace # with $(pound)
rather than with \#. There might very well be other places that need
similar fixup in preparation for whatever future Make release contains
the above change, but at least this builds an x86_64 defconfig with the
new make.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197847
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Alex Kiernan [Tue, 18 Sep 2018 08:11:55 +0000 (08:11 +0000)]
spl: mmc: Report device number when we fail
If we fail to find the MMC boot device, report the number of the one
we were looking for in the error to aid diagnosis.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Liviu Dudau [Mon, 17 Sep 2018 16:50:00 +0000 (17:50 +0100)]
clk: Add support for Arm's Versatile Express OSC clock generators
The Arm Versatile Express and Juno development boards contain an
OSC clock generator that can be accessed through the Versatile
Express config bus. The generators are quite often being controlled
by some MCU and the config bus offers a uniform way of exposing them.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Neil Stainton [Wed, 12 Sep 2018 11:02:51 +0000 (11:02 +0000)]
cmd: env: Fix CRC calculation for 'env export -c -s'
Fix failure to reimport exported checksummed, size constrained data block.
'env export -c' command ignores optional -s size argument when calculating checksum causing subsequent 'env import -c' to fail.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
Tom Rini [Sun, 30 Sep 2018 02:28:44 +0000 (22:28 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Signed-off-by: Tom Rini <trini@konsulko.com>
Rajan Vaja [Wed, 19 Sep 2018 10:43:46 +0000 (03:43 -0700)]
dm: test: Add "/firmware" node scan test
Add a test which verifies that all subnodes under "/firmware"
nodes are scanned.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed
ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile,
updated #if condition in drivers/firmware/firmware-uclass.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
Rajan Vaja [Wed, 19 Sep 2018 10:43:43 +0000 (03:43 -0700)]
firmware: Add FIRMWARE config prompt string
There is no prompt string for FIRMWARE config. Without this,
FIRMWARE config cannot be enabled through menuconfing or
config file. Fix this by adding prompt summary.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 19 Sep 2018 00:43:28 +0000 (18:43 -0600)]
sandbox: Add an explanation of the sandbox variants
There are quite a few builds of sandbox now. Add information about these
to the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 18 Sep 2018 05:55:42 +0000 (23:55 -0600)]
buildman: Avoid hanging when the config changes
Something has changed in the last several month such that when buildman
builds U-Boot incrementally and a new CONFIG option has been added to the
Kconfig, the build hanges waiting for input:
Test new config (NEW_CONFIG) [N/y/?] (NEW)
Since binamn does not connect the build's stdin to anything this waits on
stdin to the build thread, which never comes. Eventually I suspect all the
threads end up in this state and the build does not progress.
Fix this by passing /dev/null as input to the build. That way, if there is
a new CONFIG, the build will stop (and fail):
Test new config (NEW_CONFIG) [N/y/?] (NEW)
Error in reading or end of file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Liviu Dudau [Mon, 17 Sep 2018 16:46:07 +0000 (17:46 +0100)]
include/dm.h: Remove duplicated include directive
Remove duplicated inclusion of dm/ofnode.h
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Liviu Dudau [Mon, 17 Sep 2018 16:43:08 +0000 (17:43 +0100)]
include/clk.h: Fix the name of the clock uclass in comment
The comment references a structure name that doesn't exist. Use
the name of the actual uclass.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Jens Wiklander [Mon, 20 Aug 2018 09:09:59 +0000 (11:09 +0200)]
fdt: fdtdec_setup_memory_banksize() use livetree
Converts fdtdec_setup_memory_banksize() to use ofnode functions instead.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Marek Vasut [Wed, 8 Aug 2018 20:10:44 +0000 (22:10 +0200)]
cmd: clk: Add trivial implementation of clock dump for DM
Add trivial implementation of the clk dump in case DM is enabled.
This implementation just iterates over all the clock registered
with the CLK uclass and prints their rate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Mario Six [Tue, 31 Jul 2018 09:44:13 +0000 (11:44 +0200)]
test: Add tests for board uclass
Add tests for the new board uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Tue, 31 Jul 2018 09:44:12 +0000 (11:44 +0200)]
board: Add gazerbeam driver
Add a board driver for the upcoming gdsys Gazerbeam board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mario Six [Tue, 31 Jul 2018 09:44:11 +0000 (11:44 +0200)]
drivers: Add board uclass
Since there is no canonical "board device" that can be used in board
files, it is difficult to use DM function for board initialization in
these cases.
Hence, add a uclass that implements a simple "board device", which can
hold devices not suitable anywhere else in the device tree, and is also
able to read encoded information, e.g. hard-wired GPIOs on a GPIO
expander, read-only memory ICs, etc. that carry information about the
hardware.
The devices of this uclass expose methods to read generic data types
(integers, strings, booleans) to encode the information provided by the
hardware.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Tue, 26 Jun 2018 06:46:51 +0000 (08:46 +0200)]
test: Add tests for dev_{enable, disable}_by_path
Add tests for the dev_{enable,disable}_by_path functions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Tue, 26 Jun 2018 06:46:50 +0000 (08:46 +0200)]
core: Add dev_{disable,enable}_by_path
We cannot use device structures to disable devices, since getting
them with the API functions would bind and activate the device, which
would fail if the underlying device does not exist.
Reviewed-by: Simon Glass <sjg@chromium.org>
Mario Six [Tue, 26 Jun 2018 06:46:49 +0000 (08:46 +0200)]
test: Add tests for DT-manipulation functions
Add tests for the ofnode_set_enabled, ofnode_write_string, and
ofnode_write_property functions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Tue, 26 Jun 2018 06:46:48 +0000 (08:46 +0200)]
core: Add functions to set properties in live-tree
Implement a set of functions to manipulate properties in a live device
tree:
* ofnode_write_prop() to set generic properties of a node
* ofnode_write_string() to set string properties of a node
* ofnode_set_enabled() to either enable or disable a node
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:36 +0000 (04:57 -0600)]
binman: Allow writing a map file when something goes wrong
When we get a problem like overlapping regions it is sometimes hard to
figure what what is going on. At present we don't write the map file in
this case. However the file does provide useful information.
Catch any packing errors and write a map file (if enabled with -m) to aid
debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:35 +0000 (04:57 -0600)]
binman: Support ELF files for U-Boot and SPL
For sandbox we want to put ELF files in the image since that is what we
need to execute. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:34 +0000 (04:57 -0600)]
binman: Correct fmap output on x86
Normally x86 platforms use the end-at-4gb option. This currently produces
an FMAP with positions which have a large offset. The use of end-at-4gb is
a useful convenience within binman, but we don't really want to export
a map with these offsets.
Fix this by subtracting the 'skip at start' parameter.
Also put the code which convers names to fmap format, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:33 +0000 (04:57 -0600)]
binman: Record the parent section of each section
At present sections have no record of their parent so it is not possible
to traverse up the tree to the root and figure out the position of a
section within the image.
Change the constructor to record this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:32 +0000 (04:57 -0600)]
binman: Support x86 microcode in TPL
When TPL is used on x86 we may want to program the microcode (at least for
the first CPU) early in boot. Add support for this by refactoring the
existing code to be more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:31 +0000 (04:57 -0600)]
binman: Support hashing entries
Sometimesi it us useful to be able to verify the content of entries with
a hash. Add an easy way to do this in binman. The hash information can be
retrieved from the device tree at run time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:30 +0000 (04:57 -0600)]
binman: Mention section attributes in docs
Images and sections have the same attributes, since an image is mostly
just a top-level section. Update the docs to explain this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:29 +0000 (04:57 -0600)]
binman: Support expanding entries
It is useful to have entries which can grow automatically to fill
available space. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:28 +0000 (04:57 -0600)]
binman: Support adding files
In some cases it is useful to add a group of files to the image and be
able to access them at run-time. Of course it is possible to generate
the binman config file with a set of blobs each with a filename. But for
convenience, add an entry type which can do this.
Add required support (for adding nodes and string properties) into the
state module.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:27 +0000 (04:57 -0600)]
binman: Allow zero-size sections
At present if there is only a zero-size entry in a section this is
reported as an error, e.g.:
Offset 0x0 (0) is outside the section starting at 0x0 (0)
Adjust the logic in CheckEntries() to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 14 Sep 2018 10:57:26 +0000 (04:57 -0600)]
binman: Support compressed entries
Add support for compressing blob entries. This can help reduce image sizes
for many types of data. It requires that the firmware be able to
decompress the data at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>