Phil Elwell [Tue, 27 Oct 2020 12:12:22 +0000 (12:12 +0000)]
bcm2708_fb: Fix a build warning
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Serge Schneider [Mon, 26 Oct 2020 16:38:21 +0000 (16:38 +0000)]
rpisense-fb: Set pseudo_pallete to prevent crash on fbcon takeover
Signed-off-by: Serge Schneider <serge@raspberrypi.com>
Phil Elwell [Wed, 30 Sep 2020 11:00:54 +0000 (12:00 +0100)]
gpio: Add gpio-fsm driver
The gpio-fsm driver implements simple state machines that allow GPIOs
to be controlled in response to inputs from other GPIOs - real and
soft/virtual - and time delays. It can:
+ create dummy GPIOs for drivers that demand them,
+ drive multiple GPIOs from a single input, with optional delays,
+ add a debounce circuit to an input,
+ drive pattern sequences onto LEDs
etc.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Fix a build warning
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Rename 'num-soft-gpios' to avoid warning
As of 5.10, the Device Tree parser warns about properties that look
like references to "suppliers" of various services. "num-soft-gpios"
resembles a declaration of a GPIO called "num-soft", causing the value
to be interpreted as a phandle, the owner of which is checked for a
"#gpio-cells" property.
To avoid this warning, rename the gpio-fsm property to "num-swgpios".
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Show state info in /sys/class/gpio-fsm
Add gpio-fsm sysfs entries under /sys/class/gpio-fsm. For each state
machine show the current state, which state (if any) will be entered
after a delay, and the current value of that delay.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Fix shutdown timeout handling
The driver is intended to jump directly to a shutdown state in the
event of a timeout during shutdown, but the sense of the test was
inverted.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Clamp the delay time to zero
The sysfs delay_ms value is calculated live, and it is possible for
the time left to appear to be negative briefly if the timer handling
hasn't completed. Ensure the displayed value never goes below zero,
for the sake of appearances.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio-fsm: Sort functions into a more logical order
Move some functions into a more logical ordering. This change causes
no functional change and is essentially cosmetic.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio_fsm: Rework the atomic-vs-non-atomic split
Partition the code to separate atomic and non-atomic methods so that
none of them have to handle both cases. The result avoids using deferred
work unless necessary, and should be easier to understand.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Naushir Patuck [Thu, 23 Apr 2020 09:17:37 +0000 (10:17 +0100)]
staging: vc04_services: ISP: Add a more complex ISP processing component
Driver for the BCM2835 ISP hardware block. This driver uses the MMAL
component to program the ISP hardware through the VC firmware.
The ISP component can produce two video stream outputs, and Bayer
image statistics. This can't be encompassed in a simple V4L2
M2M device, so create a new device that registers 4 video nodes.
This patch squashes all the development patches from the earlier
rpi-5.4.y branch into one
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Dave Stevenson [Mon, 12 Oct 2020 16:03:14 +0000 (17:03 +0100)]
uapi: bcm2835-isp: Add bcm2835-isp uapi header file
This file defines the userland interface to the bcm2835-isp driver
that will follow in a separate commit.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 8 Oct 2020 19:24:12 +0000 (20:24 +0100)]
staging: vc04_services: Add a V4L2 M2M codec driver
This adds a V4L2 memory to memory device that wraps the MMAL
video decode and video_encode components for H264 and MJPEG encode
and decode, MPEG4, H263, and VP8 decode (and MPEG2 decode
if the appropriate licence has been purchased).
This patch squashes all the work done in developing the driver
on the Raspberry Pi rpi-5.4.y kernel branch.
Thanks to Kieran Bingham, Aman Gupta, Chen-Yu Tsai, and
Marek BehĂșn for their contributions. Please refer to the
rpi-5.4.y branch for the full history.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Ensure OUTPUT timestamps are always forwarded
The firmware by default tries to ensure that decoded frame
timestamps always increment. This is counter to the V4L2 API
which wants exactly the OUTPUT queue timestamps passed to the
CAPTURE queue buffers.
Disable the firmware option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04_services/codec: Add support for CID MPEG_HEADER_MODE
Control V4L2_CID_MPEG_VIDEO_HEADER_MODE controls whether the encoder
is meant to emit the header bytes as a separate packet or with the
first encoded frame.
Add support for it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04_services/codec: Clear last buf dequeued flag on START
It appears that the V4L2 M2M framework requires the driver to manually
call vb2_clear_last_buffer_dequeued on the CAPTURE queue during a
V4L2_DEC_CMD_START.
Add such a call.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc04-services/codec: Fix logical precedence issue
Two issues identified with operator precedence in logical
expressions. Fix them.
https://github.com/raspberrypi/linux/issues/4040
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Switch to s32fract
staging/bcm2835-codec: Add the unpacked (16bpp) raw formats
Now that the firmware supports the unpacked (16bpp) variants
of the MIPI raw formats, add the mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Log the number of excess supported formats
When logging that the firmware has provided more supported formats
than we had allocated storage for, log the number allocated and
returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add support for pixel aspect ratio
If the format is detected by the driver and a V4L2_EVENT_SOURCE_CHANGE
event is generated, then pass on the pixel aspect ratio as well.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Implement additional g_selection calls for decode
v4l_cropcap calls our vidioc_g_pixelaspect function to get the pixel
aspect ratio, but also calls g_selection for V4L2_SEL_TGT_CROP_BOUNDS
and V4L2_SEL_TGT_CROP_DEFAULT. Whilst it allows for vidioc_g_pixelaspect
not to be implemented, it doesn't allow for either of the other two.
Add in support for the additional selection targets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add VC-1 support.
Providing the relevant licence has been purchased, then Pi0-3
can decode VC-1.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Fix support for levels 4.1 and 4.2
The driver said it supported H264 levels 4.1 and 4.2, but
was missing the V4L2 to MMAL mappings.
Add in those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Set the colourspace appropriately for RGB formats
Video decode supports YUV and RGB formats. YUV needs to report SMPTE170M
or REC709 appropriately, whilst RGB should report SRGB.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Pass corrupt frame flag.
MMAL has the flag MMAL_BUFFER_HEADER_FLAG_CORRUPTED but that
wasn't being passed through, so add it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Do not update crop from S_FMT after res change
During decode, setting the CAPTURE queue format was setting the crop
rectangle to the requested height before aligning up the format to
cater for simple clients that weren't expecting to deal with cropping
and the SELECTION API.
This caused problems on some resolution change events if the client
didn't also then use the selection API.
Disable the crop update after a resolution change.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835: Allow compressed frames to set sizeimage (#4386)
Allow the user to set sizeimage in TRY_FMT and S_FMT if the format
flags have V4L2_FMT_FLAG_COMPRESSED set
Signed-off-by: John Cox <jc@kynesim.co.uk>
staging/bcm2835-codec: Change the default codec res to 32x32
In order to effectively guarantee that a V4L2_EVENT_SOURCE_CHANGE
event occurs, adopt a default resolution of 32x32 so that it
is incredibly unlikely to be decoding a stream of that resolution
and therefore failing to note a "change" requiring the event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Add support for decoding interlaced streams
The video decoder can support decoding interlaced streams, so add
the required plumbing to signal this correctly.
The encoder and ISP do NOT support interlaced data, so trying to
configure an interlaced format on those nodes will be rejected.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Correct ENUM_FRAMESIZES stepsize to 2
Being YUV420 formats, the step size is always 2 to avoid part
chroma subsampling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Return buffers to QUEUED not ERROR state
Should start_streaming fail, or buffers be queued during
stop_streaming, they should be returned to the core as QUEUED
and not (as currently) as ERROR.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835_codec: Log MMAL flags in hex
The flags is a bitmask, so it's far easier to interpret as hex
data instead of decimal.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Allow custom specified strides/bytesperline.
If the client provides a bytesperline value in try_fmt/s_fmt then
validate it and correct if necessary.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835_codec: Add support for image_fx to deinterlace
Adds another /dev/video node wrapping image_fx doing deinterlace.
Co-developed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging/bcm2835-v4l2_codec: Fix for encode selection API
Matches correct behaviour from DECODE and DEINTERLACE
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging: bcm2835-codec: Allow decode res changed before STREAMON(CAPTURE)
The V4L2 stateful video decoder API requires that you can STREAMON
on only the OUTPUT queue, feed in buffers, and wait for the
SOURCE_CHANGE event.
This requires that we enable the MMAL output port at the same time
as the input port, because the output port is the one that creates
the SOURCE_CHANGED event.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Do not send buffers to the VPU unless streaming
With video decode we now enable both input and output ports on
the component. This means that buffers will get passed to the VPU
earlier than desired if they are queued befoer STREAMON.
Check that the queue is streaming before sending buffers to the VPU.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Format changed should trigger drain
When a format changed event occurs, the spec says that it
triggers an implicit drain, and that needs to be signalled
via -EPIPE.
For BCM2835, the format changed event happens at the point
the format change occurs, so no further buffers exist from
before the resolution changed point. We therefore signal the
last buffer immediately.
We don't have a V4L2 available to us at this point, so set
the videobuf2 queue last_buffer_dequeued flag directly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Signal the firmware to stop on all changes
The firmware defaults to not stopping video decode if only the
pixel aspect ratio or colourspace change. V4L2 requires us
to stop decoding on any change, therefore tell the firmware
of the desire for this alternate behaviour.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Queue flushed buffers instead of completing
When a buffer is returned on a port that is disabled, return it
to the videobuf2 QUEUED state instead of DONE which returns it
to the client.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835_codec: Correct flushing code for refcounting
Completions don't reference count, so setting the completion
on the first buffer returned and then not reinitialising it
means that the flush function doesn't behave as intended.
Signal the completion when the last buffer is returned.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Ensure all ctrls are set on streamon
Currently the code was only setting some controls from
bcm2835_codec_set_ctrls, but it's simpler to use
v4l2_ctrl_handler_setup to avoid forgetting to adding new
controls to the list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add support for H&V Flips to ISP
The ISP can do H & V flips whilst resizing or converting
the image, so expose that via V4L2_CID_[H|V]FLIP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835-v4l2-codec: Remove advertised support of VP8
The support for this format by firmware is very limited
and won't be faster than the arm.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Pass V4L2_CID_MPEG_VIDEO_H264_MIN_QP/MAX_QP to bcm2835-v4l2-codec
Following raspberrypi/linux#4704. This is necessary to set up
quantization for variable bitrate to avoid video flickering.
staging/bcm2835-codec: bytesperline for YUV420/YVU420 needs to be 64
Matching https://github.com/raspberrypi/linux/pull/4419, the ISP
block (which is also used on the input of the encoder, and output
of the decoder) needs the base address of all planes to be aligned
to multiples of 32. This includes the chroma planes of YUV420 and
YVU420.
If the height is only a multiple of 2 (not 4), then you get an odd
number of lines in the second plane, which means the 3rd plane
starts at a multiple of bytesperline/2.
Set the minimum bytesperline alignment to 64 for those formats
so that the plane alignment is always right.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/bcm2835-codec: Allow a different stride alignment per role
Deinterlace and decode aren't affected in the same way as encode
and ISP by the alignment requirement on 3 plane YUV420.
Decode would be affected, but it always aligns the height up to
a macroblock, and uses the selection API to reflect that.
Add in the facility to set the bytesperline alignment per role.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vc04_services: codec: Add support for V4L2_PIX_FMT_RGBA32 format
We already support V4L2_PIX_FMT_BGR32 which is the same thing with red
and blue swapped, so it makes sense to include this variant as well.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
bcm2835-codec: Return empty buffers to the VPU instead of queueing to vbuf2
The encoder can skip frames totally should rate control overshoot
the target bitrate too far. In this situation it generates an
output buffer of length 0.
V4L2 treats a buffer of length 0 as an end of stream flag, which is
not appropriate in this case, therefore we can not return that buffer
to the client.
The driver was returning the buffer to videobuf2 in the QUEUED state,
however that buffer was then not dequeued again, so the number of
buffers was reduced each time this happened. In the pathological
case of using GStreamer's videotestsrc in mode 1 for noise, this happens
sufficiently frequently to totally stall the pipeline.
If the port is still enabled then return the buffer straight back to
the VPU rather than to videobuf2.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Add support for V4L2_PIX_FMT_NV12_COL128
V4L2_PIX_FMT_NV12_COL128 is supported by the ISP and the input of
video_encode, output of video_decode, and both input and output
of the ISP.
Add in the plumbing to support the format on those ports.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Set crop_height for compressed formats
In particular for the encoder where the CAPTURE format dictates
the parameters given to the codec we need to be able to set the
value passed as the crop_height for the compressed format.
There's no crop available for cropped modes, so always set
crop_height to the requested height.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Set port format from s_selection
s_selection allows the crop region of an uncompressed pixel
format to be specified, but it wasn't passing the setting on to
the firmware. Depending on call order this would potentially
mean that the crop wasn't actioned.
Set the port format on s_selection if we have a component created.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
bcm2835-codec: /dev/video31 as interface to image_encode JPEG encoder
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
bcm2835-v4l2-codec: support H.264 5.0 and 5.1 levels
vc04_services: bcm2835-codec: Remove redundant role check
vidioc_try_encoder_cmd checks the role, but the ioctl is disabled
for any roles in which it is invalid.
Remove the redundant check.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835-codec: Allow encoder_cmd on ISP and deinterlace
ISP and deinterlace also need a mechanism for passing effectively
an EOS through the pipeline to signal when all buffers have been
processed.
VIDIOC_ENCODER_CMD does exactly this for encoders, so reuse the same
function for ISP and deinterlace.
(VIDIOC_DECODER_CMD is slightly different in that it also passes
details of when and how to stop, so is not as relevant).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835_codec: Allow larger images through the ISP
Whilst the codecs are restricted to 1920x1080 / 1080x1920, the ISP
isn't, but the limits advertised via V4L2 was 1920x1920 for all
roles.
Increase the limit to 16k x 16k for the ISP.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: bcm2835-v4l2-codec: Enable selection ioctl for ISP
The ISP cases do nothing. Remove the break that separates them from the
deinterlace case so they now do the same as deinterlace. This enables
simple width & height setting, but does not enable setting left and
top coordinates.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: bcm2835-v4l2-codec: Add profile & level ctrls to decode
In order to support discovery of what profile & levels are supported by
stateful decoders implement the profile and level controls where they
are defined by V4L2.
Signed-off-by: John Cox <jc@kynesim.co.uk>
vc04_services: bcm2835_codec: Ignore READ_ONLY ctrls in s_ctrl
In adding the MPEG2/MPEG4/H264 level and profile controls to
the decoder, they weren't declared as read-only, nor handlers
added to bcm2835_codec_s_ctrl. That resulted in an error message
"Invalid control" being logged every time v4l2_ctrl_handler_setup
was called from bcm2835_codec_create_component.
Define those controls as read only, and exit early from s_ctrl
on read only controls.
Fixes: "media: bcm2835-v4l2-codec: Add profile & level ctrls to decode"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc04_services: bcm2835_codec: Set MPEG2_LEVEL control to READ_ONLY
V4L2_CID_MPEG_VIDEO_MPEG2_LEVEL was missed from
"vc04_services: bcm2835_codec: Ignore READ_ONLY ctrls in s_ctrl"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add V4L2_CID_MPEG_VIDEO_B_FRAMES control
FFmpeg insists on trying to set V4L2_CID_MPEG_VIDEO_B_FRAMES to
0, and generates an error should it fail.
As our encoder doesn't support B frames, add a stub handler for
it to silence FFmpeg.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add support for V4L2_CID_MPEG_VIDEO_GOP_SIZE
For H264, V4L2_CID_MPEG_VIDEO_H264_I_PERIOD is meant to be the intra
I-frame period, whilst V4L2_CID_MPEG_VIDEO_GOP_SIZE is the intra IDR
frame period.
The firmware encoder doesn't produce I-frames that aren't IDR as well,
therefore V4L2_CID_MPEG_VIDEO_GOP_SIZE is technically the correct
control, however users may have adopted V4L2_CID_MPEG_VIDEO_H264_I_PERIOD.
Add support for V4L2_CID_MPEG_VIDEO_GOP_SIZE controlling the encoder,
and have VIDIOC_S_CTRL for V4L2_CID_MPEG_VIDEO_H264_I_PERIOD update
the value for V4L2_CID_MPEG_VIDEO_GOP_SIZE (the reverse is not
implemented).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Add missing alignment for V4L2_PIX_FMT_RGBA32
The patch adding image encode (JPEG) to the driver missed adding
the alignment constraint for V4L2_PIX_FMT_RGBA32, which meant
it ended up giving a stride and size of 0.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: bcm2835-codec: Downgrade the level for a debug message
The debug message from bcm2835_codec_buf_prepare when the buffer
size is incorrect can be a little spammy if the application isn't
careful on how it drives it, therefore drop the priority of the
message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 25 Sep 2018 15:07:55 +0000 (16:07 +0100)]
staging: mmal-vchiq: Use vc-sm-cma to support zero copy
With the vc-sm-cma driver we can support zero copy of buffers between
the kernel and VPU. Add this support to mmal-vchiq.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc-sm-cma: fixed kbuild problem
error logs:
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1:error: recursive dependency detected!
drivers/staging/vc04_services/vc-sm-cma/Kconfig:1: symbol BCM_VC_SM_CMA is selected by BCM2835_VCHIQ_MMAL
drivers/staging/vc04_services/vchiq-mmal/Kconfig:1: symbol BCM2835_VCHIQ_MMAL depends on BCM2835_VCHIQ
drivers/staging/vc04_services/Kconfig:14: symbol BCM2835_VCHIQ is selected by BCM_VC_SM_CMA
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
Tested-by: make ARCH=arm64 bcm2711_defconfig
Test platform: fedora 33
Branch: rpi-5.10.y
Dave Stevenson [Wed, 6 May 2020 17:11:14 +0000 (18:11 +0100)]
staging: mmal-vchiq: Add monochrome image formats
Adds support for monochrome image formats in the various
MIPI packings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 6 May 2020 17:09:04 +0000 (18:09 +0100)]
staging: vchiq-mmal: Add support for 14bit Bayer
Add in the missing defines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 8 Oct 2020 17:49:52 +0000 (18:49 +0100)]
staging: vc04_services: Add new vc-sm-cma driver
Add Broadcom VideoCore Shared Memory support.
This new driver allows contiguous memory blocks to be imported
into the VideoCore VPU memory map, and manages the lifetime of
those objects, only releasing the source dmabuf once the VPU has
confirmed it has finished with it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging: vcsm-cma: Fix memory leak from not detaching dmabuf
When importing there was a missing call to detach the buffer,
so each import leaked the sg table entry.
Actually the release process for both locally allocated and
imported buffers is identical, so fix them to both use the same
function.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
staging/vc-sm-cma: Avoid log spamming on Pi0/1 over cache alias.
Pi 0/1 use the 0x80000000 cache alias as the ARM also sees the world
through the VPU L2 cache.
vc-sm-cma was trying to ensure it was in an uncached alias (0xc), and
complaining on every allocation if it weren't. Reduce this logging.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc-sm-cma: Restore correct cache maintainance operations
We have been using the more expensive flush operations rather than
invalidate and clean since kernel rpi-5.9.y
These are exposed with:
52f1453513ba95084ab811a030032fe605b0cbe2 Re-expose some dmi APIs for use in VCSM
But I believe that commit was dropped when (non-cma) vc-sm was dropped,
and didn't get updated when the commit was restored
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
staging: vc04_services: Fix clang14 warning
Insert a break to fix a fallthrough warning from clang14. Since the
fallthrough was to another break, this is a cosmetic change.
See: https://github.com/raspberrypi/linux/issues/5078
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
vc04_services/vc-sm-cma: Handle upstream require vchiq_instance to be passed around
vc04_services/vc-sm-cma: Switch one-bit bitfields to bool
Clang 16 warns:
../drivers/staging/vc04_services/vc-sm-cma/vc_sm.c:816:19: warning: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Wsingle-bit-bitfield-constant-conversion]
buffer->imported = 1;
^ ~
../drivers/staging/vc04_services/vc-sm-cma/vc_sm.c:822:17: warning: implicit truncation from 'int' to a one-bit wide bit-field changes value from 1 to -1 [-Wsingle-bit-bitfield-constant-conversion]
buffer->in_use = 1;
^ ~
2 warnings generated.
Signed-off-by: Alexander Winkowski <dereference23@outlook.com>
vc04_services: vcsm-cma: Detach from the correct dmabuf
Commit
d3292daee319 ("dma-buf: Make locking consistent in dma_buf_detach()")
added checking that the same dmabuf for which dma_buf_attach
was called is passed into dma_buf_detach, which flagged up
that vcsm-cma was passing in the wrong dmabuf.
Correct this so that we don't get the WARN on every dma_buf
release.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 8 Oct 2020 14:35:14 +0000 (15:35 +0100)]
staging: bcm2835-camera: Replace deprecated V4L2_PIX_FMT_BGR32
V4L2_PIX_FMT_BGR32 is deprecated as it is ambiguous over where
the alpha byte is. Cheese/GStreamer appear to get it wrong for
one, and qv4l2 gets red and blue swapped.
Swap to the newer V4L2_PIX_FMT_BGRX32 format.
https://www.raspberrypi.org/forums/viewtopic.php?f=38&t=267736&p=1738912
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
popcornmix [Mon, 28 Sep 2020 19:23:30 +0000 (20:23 +0100)]
char: Add broadcom char drivers back to build files
See: https://github.com/raspberrypi/linux/issues/3875
Signed-off-by: popcornmix <popcornmix@gmail.com>
Phil Elwell [Fri, 25 Sep 2020 14:07:23 +0000 (15:07 +0100)]
net: bcmgenet: Reset RBUF on first open
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 3 Feb 2020 09:32:22 +0000 (09:32 +0000)]
brcmfmac: Increase power saving delay to 2s
Increase the delay before entering the lower power state to 2 seconds
(the maximum allowed) in order to reduce the packet latencies,
particularly for inbound packets.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Tue, 1 Sep 2020 17:15:27 +0000 (18:15 +0100)]
staging/fbtft: Add support for display variants
Display variants are intended as a replacement for the now-deleted
fbtft_device drivers. Drivers can register additional compatible
strings with a custom callback that can make the required changes
to the fbtft_display structure.
Start the ball rolling by adding adafruit18, adafruit18_green and
sainsmart18 displays.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
David Plowman [Thu, 28 May 2020 10:09:48 +0000 (11:09 +0100)]
media: bcm2835-unicam: change minimum number of vb2_queue buffers to 1
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Dave Stevenson [Tue, 19 May 2020 10:46:47 +0000 (11:46 +0100)]
media: bcm2835-unicam: Retain packing information on G_FMT
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 23 Jun 2020 14:14:05 +0000 (15:14 +0100)]
media: bcm2835-unicam: Fixup review comments from Hans.
Updates the driver based on the upstream review comments from
Hans Verkuil at https://patchwork.linuxtv.org/patch/63531/
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Jacko Dirks [Tue, 5 May 2020 12:33:31 +0000 (14:33 +0200)]
media: bcm2835: unicam: Fix uninitialized warning
Signed-off-by: Jacko Dirks <jdirks.linuxdev@gmail.com>
Dave Stevenson [Wed, 13 May 2020 17:28:27 +0000 (18:28 +0100)]
media: bcm2835-unicam: Always service interrupts
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 10 Jul 2020 11:40:50 +0000 (12:40 +0100)]
media: i2c: tc358743: Only allow supported pixel fmts in set_fmt
Fix commit "media: tc358743: Return an appropriate colorspace from
tc358743_set_fmt" to ensure that the format passed in to set_fmt
is checked to be valid, and reset to the current format if not.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 27 Aug 2020 15:30:26 +0000 (16:30 +0100)]
media: bcm2835-unicam: Drop WARN on uing direct cache alias
Pi 0&1 pass all ARM accesses through the VPU L2 cache, therefore
the dma-ranges property sets the cache alias bits to other
than the direct alias, hence this WARN was firing.
It was overprotective coding, so assume that everything is OK
with the dma-ranges, and remove the WARN.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Mon, 13 Jul 2020 09:33:19 +0000 (10:33 +0100)]
leds: Add the actpwr trigger
The actpwr trigger is a meta trigger that cycles between an inverted
mmc0 and default-on. It is written in a way that could fairly easily
be generalised to support alternative sets of source triggers.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Naushir Patuck [Mon, 11 May 2020 12:06:27 +0000 (13:06 +0100)]
dt-bindings: bcm2835-unicam: Update documentation with new clock params
Update the documentation to reflect the new "VPU" clock needed
by the bcm2835-unicam driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Mon, 11 May 2020 12:02:22 +0000 (13:02 +0100)]
media: bcm2835: unicam: Set VPU min clock freq to 250Mhz.
When streaming with Unicam, the VPU must have a clock frequency of at
least 250Mhz. Otherwise, the input fifos could overrun, causing
image corruption.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Dave Stevenson [Tue, 7 Jul 2020 13:52:43 +0000 (14:52 +0100)]
media: bcm2835-unicam: Ensure type is VIDEO_CAPTURE in [g|s]_selection
[g|s]_selection pass in a buffer type that needs to be validated
before passing on to the sensor subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 7 Jul 2020 13:23:40 +0000 (14:23 +0100)]
media: bcm2835-unicam: Reinstate V4L2_CAP_READWRITE in the caps
v4l2-compliance throws a failure if the device doesn't advertise
V4L2_CAP_READWRITE but allows read or write operations.
We do support read, so reinstate the flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 1 Jul 2020 09:57:57 +0000 (10:57 +0100)]
media: bcm2835-unicam: Add support for unpacked 14bit Bayer formats
Now that the 14bit non-packed Bayer formats are defined, add them
into the supported formats lookup table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 17:03:47 +0000 (18:03 +0100)]
media: bcm2835-unicam: Add support for 14bit mono sources
Now that V4L2_PIX_FMT_Y14 and V4L2_PIX_FMT_Y14P are defined,
allow passing 14bit mono data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 16:53:32 +0000 (17:53 +0100)]
media: bcm2835-unicam: Add support for 12bit mono packed format
Now that V4L2_PIX_FMT_Y12P is defined, allow passing raw 12bit
mono packed data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 16:51:03 +0000 (17:51 +0100)]
media: Add a pixel format for MIPI packed 14bit luma only.
This is the format used by monochrome 14bit image sensors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 7 May 2020 15:59:03 +0000 (16:59 +0100)]
media: Add a pixel format for MIPI packed 12bit luma only.
This is the format used by monochrome 12bit image sensors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Thu, 2 Jul 2020 12:53:20 +0000 (13:53 +0100)]
serial: 8250: bcm2835aux - defer if clock is zero
See: https://github.com/raspberrypi/linux/issues/3700
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Dave Stevenson [Fri, 26 Jun 2020 14:53:44 +0000 (15:53 +0100)]
media: bcm2835-unicam: Avoid gcc warning over {0} on endpoint
Older gcc versions object to = { 0 } initialisation if the first
elemtn in the structure is a substructure.
Use = { } to avoid this compiler warning.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 23 Jun 2020 13:32:51 +0000 (14:32 +0100)]
media: bcm2835-unicam: Add support for get_mbus_config to set num lanes
Use the get_mbus_config pad subdev call to allow a source to use
fewer than the number of CSI2 lanes defined in device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Naushir Patuck [Wed, 1 Apr 2020 07:39:49 +0000 (08:39 +0100)]
media: bcm2835-unicam: Kconfig/Makefile for CCP2/CSI2 camera interface
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Mon, 4 May 2020 09:25:41 +0000 (12:25 +0300)]
media: bcm2835-unicam: Driver for CCP2/CSI2 camera interface
Add a driver for the Unicam camera receiver block on BCM283x processors.
Compared to the bcm2835-camera driver present in staging, this driver
handles the Unicam block only (CSI-2 receiver), and doesn't depend on
the VC4 firmware running on the VPU.
The commit is made up of a series of changes cherry-picked from the
rpi-5.4.y branch of https://github.com/raspberrypi/linux/ with
additional enhancements, forward-ported to the mainline kernel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: kbuild test robot <lkp@intel.com>
Phil Elwell [Fri, 26 Jun 2020 10:51:05 +0000 (11:51 +0100)]
brcmfmac: Prefer a ccode from OTP over nvram file
Allow the nvram file to set a default ccode (regulatory domain) without
overriding one set in OTP.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Markus Proeller [Tue, 16 Jun 2020 11:33:56 +0000 (13:33 +0200)]
media: irs1125: Keep HW in sync after imager reset
When closing the video device, the irs1125 is put in power down state.
To keep V4L2 ctrls and the HW in sync, v4l2_ctrl_handler_setup is
called after power up.
The compound ctrl IRS1125_CID_MOD_PLL however has a default value
of all zeros, which puts the imager into a non responding state.
Thus, this ctrl is not written by the driver into HW after power up.
The userspace has to take care to write senseful data.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Tue, 16 Jun 2020 11:31:36 +0000 (13:31 +0200)]
media: irs1125: Atomic access to imager reconfiguration
Instead of changing the exposure and framerate settings for all sequences,
they can be changed for every sequence individually now. Therefore the
IRS1125_CID_SAFE_RECONFIG ctrl has been removed and replaced by
IRS1125_CID_SAFE_RECONFIG_S<seq_num>_EXPO and *_FRAME ctrls.
The consistency check in the sequence ctrl IRS1125_CID_SEQ_CONFIG
is removed.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Tue, 16 Jun 2020 11:27:42 +0000 (13:27 +0200)]
media: irs1125: Refactoring and debug messages
Changed some variable names to comply with checkpatch --strict mode.
Debug messages added.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Tue, 16 Jun 2020 11:24:31 +0000 (13:24 +0200)]
media: irs1125: Using i2c_transfer for ic2 reads
Reading data over i2c is done by using i2c_transfer to ensure that this
operation can't be interrupted.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Phil Elwell [Thu, 11 Jun 2020 08:57:03 +0000 (09:57 +0100)]
PCI: brcmstb: Add DT property to control L1SS
The BRCM PCIe block has controls to enable control of the CLKREQ#
signal by the L1SS, and to gate the refclk with the CLKREQ# input.
These controls are mutually exclusive - the upstream code sets the
latter, but some use cases require the former.
Add a Device Tree property - brcm,enable-l1ss - to switch to the
L1SS configuration.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Tue, 24 Apr 2018 13:42:27 +0000 (14:42 +0100)]
gpiolib: Don't prevent IRQ usage of output GPIOs
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Fri, 15 May 2020 12:48:59 +0000 (13:48 +0100)]
staging:vc04_services: bcm2835-camera: Request headers with I-frame
V4L2 wishes to have the codec header bytes in the same buffer as the
first encoded frame, so it does become 1-in 1-out for encoding.
The firmware now has an option to do this, so enable it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 15 May 2020 12:42:10 +0000 (13:42 +0100)]
staging: vc04_services: mmal-vchiq: Update parameters list
Adds in a couple of new MMAL parameter defines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Tue, 5 May 2020 18:45:41 +0000 (19:45 +0100)]
video: bcm2708_fb: Disable FB if no displays found
If the firmware hasn't detected a display, the driver would assume
one display was available, but because it had failed to retrieve the
display size it would try to allocate a zero-sized buffer.
Avoid the allocation failure by bailing out early if no display is
found.
See: https://github.com/raspberrypi/linux/issues/3598
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Jacko Dirks [Tue, 5 May 2020 12:28:14 +0000 (14:28 +0200)]
media: i2c: tc358743: Fix fallthrough warning
Signed-off-by: Jacko Dirks <jdirks.linuxdev@gmail.com>
Naushir Patuck [Wed, 22 Apr 2020 07:32:32 +0000 (08:32 +0100)]
staging: vchiq: Load bcm2835_isp driver from vchiq
bcmn2835_isp is a platform driver dependent on vchiq,
therefore add the load/unload functions for it to vchiq.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Tue, 21 Apr 2020 14:06:19 +0000 (15:06 +0100)]
media: uapi: v4l-ctrls: Add CID base for the bcm2835-isp driver
We are reserving controls for the new bcm2835-isp driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Thu, 23 Apr 2020 09:20:26 +0000 (10:20 +0100)]
media: uapi: v4l2-core: Add ISP statistics output V4L2 fourcc type
Add V4L2_META_FMT_BCM2835_ISP_STATS V4L2 format type.
This new format will be used by the BCM2835 ISP device to return
out ISP statistics for 3A.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Tue, 21 Jan 2020 14:06:47 +0000 (14:06 +0000)]
media: uapi: Add MEDIA_BUS_FMT_SENSOR_DATA media bus format
This patch adds MEDIA_BUS_FMT_SENSOR_DATA used by the bcm2835-unicam
driver to support CSI-2 embedded data streams from camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Wed, 1 Apr 2020 07:46:29 +0000 (08:46 +0100)]
media: uapi: v4l2-core: Add sensor ancillary data V4L2 foucc type.
Add V4L2_META_FMT_SENSOR_DATA format 4CC.
This new format will be used by the BCM2835 Unicam device to return
out camera sensor embedded data.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Phil Elwell [Fri, 17 Apr 2020 09:46:19 +0000 (10:46 +0100)]
spi: Force CS_HIGH if GPIO descriptors are used
Commit
f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change breaks drivers whose probe functions set the mode field of
the spi_device because in doing so they clear the SPI_CS_HIGH flag.
Fix by setting SPI_CS_HIGH in spi_setup (under the same conditions as
in of_spi_parse_dt()).
See also:
83b2a8fe43bd ("spi: spidev: Fix CS polarity if GPIO descriptors are used")
Fixes:
f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
SQUASH: spi: Demote SPI_CS_HIGH warning to KERN_DEBUG
This warning is unavoidable from a client's perspective and
doesn't indicate anything wrong (just surprising).
SQUASH with "spi: use_gpio_descriptor fixup moved to spi_setup"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
John Cox [Thu, 5 Mar 2020 18:30:41 +0000 (18:30 +0000)]
staging: media: rpivid: Add Raspberry Pi V4L2 H265 decoder
This driver is for the HEVC/H265 decoder block on the Raspberry
Pi 4, and conforms to the V4L2 stateless decoder API.
Signed-off-by: John Cox <jc@kynesim.co.uk>
staging: media: rpivid: Select MEDIA_CONTROLLER and MEDIA_CONTROLLER_REQUEST_API
MEDIA_CONTROLLER_REQUEST_API is a hidden option. If rpivid depends on it,
the user would need to first enable another driver that selects
MEDIA_CONTROLLER_REQUEST_API, and only then rpivid would become available.
By selecting it instead of depending on it, it becomes possible to enable
rpivid without having to enable other potentially unnecessary drivers.
Signed-off-by: Hristo Venev <hristo@venev.name>
rpivid_h265: Fix width/height typo
Signed-off-by: popcornmix <popcornmix@gmail.com>
rpivid_h625: Fix build warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
staging: rpivid: Fix crash when CMA alloc fails
If realloc to increase coeff size fails then attempt to re-allocate
the original size. If that also fails then flag a fatal error to abort
all further decode.
Signed-off-by: John Cox <jc@kynesim.co.uk>
rpivid: Request maximum hevc clock
Query maximum and minimum clock from driver
and use those
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
rpivid: Switch to new clock api
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
rpivid: Only clk_request_done once
Fixes:
25486f49bfe2e3ae13b90478d1eebd91413136ad
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
media: rpivid: Remove the need to have num_entry_points set
VAAPI H265 has num entry points but never sets it. Allow a VAAPI
shim to work without requiring rewriting the VAAPI driver.
num_entry_points can be calculated from the slice_segment_addr
of the next slice so delay processing until we have that.
Also includes some minor cosmetics.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Convert to MPLANE
Use multi-planar interface rather than single plane interface. This
allows dmabufs holding compressed data to be resized.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Add an enable count to irq claim Qs
Add an enable count to the irq Q structures to allow the irq logic to
block further callbacks if resources associated with the irq are not
yet available.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Add a Pass0 to accumulate slices and rework job finish
Due to overheads in assembling controls and requests it is worth having
the slice assembly phase separate from the h/w pass1 processing. Create
a queue to service pass1 rather than have the pass1 finished callback
trigger the next slice job.
This requires a rework of the logic that splits up the buffer and
request done events. This code contains two ways of doing that, we use
Ezequiel Garcias <ezequiel@collabora.com> solution, but expect that
in the future this will be handled by the framework in a cleaner manner.
Fix up the handling of some of the memory exhaustion crashes uncovered
in the process of writing this code.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Map cmd buffer directly
It is unnecessary to have a separate dmabuf to hold the cmd buffer.
Map it directly from the kmalloc.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Improve values returned when setting output format
Guess a better value for the compressed bitstream buffer size
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Improve stream_on/off conformance & clock setup
Fix stream on & off such that failures leave the driver in the correct
state. Ensure that the clock is on when we are streaming and off when
all contexts attached to this device have stopped streaming.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Improve SPS/PPS error handling/validation
Move size and width checking from bitstream processing to control
validation
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Fix H265 aux ent reuse of the same slot
It is legitimate, though unusual, for an aux ent associated with a slot
to be selected in phase 0 before a previous selection has been used and
released in phase 2. Fix such that if the slot is found to be in use
that the aux ent associated with it is reused rather than an new aux
ent being created. This fixes a problem where when the first aux ent
was released the second was lost track of.
This bug spotted in Nick's testing. It may explain some other occasional,
unreliable decode error reports where dmesg included "Missing DPB AUX
ent" logging.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Update to compile with new hevc decode params
DPB entries have moved from slice params to the new decode params
attribute - update to deal with this. Also fixes fallthrough
warnings which seem to be new in 5.14.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Make slice ctrl dynamic
Allows the user to submit a whole frames worth of slice headers in
one lump along with a single bitstream dmabuf for the whole lot.
This saves potentially a lot of bitstream copying.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Only create aux entries for H265 if needed
Only create aux entries of mv info for frames where that info might
be used by a later frame. This saves some memory bandwidth and
potentially some memory.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Avoid returning EINVAL to a G_FMT ioctl
V4L2 spec says that G/S/TRY_FMT IOCTLs should never return errors for
anything other than wrong buffer types. Improve the capture format
function such that this is so and unsupported values get converted
to supported ones properly.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Remove unused ctx state variable and defines
Remove unused ctx state tracking variable and associated defines.
Their presence implies they might be used, but they aren't.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Ensure IRQs have completed before uniniting context
Before uniniting the decode context sync with the IRQ queues to ensure
that decode no longer has any buffers in use. This fixes a problem that
manifested as ffmpeg leaking CMA buffers when it did a stream off on
OUTPUT before CAPTURE, though in reality it was probably much more
dangerous than that.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: remove min_buffers_needed from src queue
Remove min_buffers_needed=1 from src queue init. Src buffers are bound
to media requests therefore this setting is not needed and generates
a WARN in kernel 5.16.
Signed-off-by: John Cox <jc@kynesim.co.uk>
rpivid: Use clk_get_max_rate()
The driver was using clk_round_rate() to figure out the maximum clock
rate that was allowed for the HEVC clock.
Since we have a function to return it directly now, let's use it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
media: rpivid: Apply V4L2 stateless API changes
media: rpivid: Fix fallthrough warning
Replace old-style /* FALLTHRU */ with fallthrough;
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Set min value as well as max for HEVC_DECODE_MODE
As only one value can be accepted set both min and max to that value.
Signed-off-by: John Cox <jc@kynesim.co.uk>
media: rpivid: Accept ANNEX_B start codes
Allow the START_CODE control to take ANNEX_B as a value. This makes no
difference to any part of the decode process as the added bytes are in
data that we ignore. This helps my testing and may help userland code
that expects to send those bytes.
Signed-off-by: John Cox <jc@kynesim.co.uk>
rpivid: Convert to new clock rate API
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Ezequiel Garcia [Sun, 21 Mar 2021 19:38:54 +0000 (16:38 -0300)]
RFC: media: Add media_request_{pin,unpin} API
This is probably not the API we will want to add, but it
should show what semantics are needed by drivers.
The goal is to allow the OUTPUT (aka source) buffer and the
controls associated to a request to be released from the request,
and in particular return the OUTPUT buffer back to userspace,
without signalling the media request fd.
This is useful for devices that are able to pre-process
the OUTPUT buffer, therefore able to release it before
the decoding is finished. These drivers should signal
the media request fd only after the CAPTURE buffer is done.
Tested-by: John Cox <jc@kynesim.co.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Dave Stevenson [Tue, 17 Mar 2020 10:53:16 +0000 (10:53 +0000)]
media: dt-bindings: media: Add binding for the Raspberry PI HEVC decoder
Adds a binding for the HEVC decoder found on the BCM2711 / Raspberry Pi 4.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 24 Jan 2020 14:28:21 +0000 (14:28 +0000)]
media: videodev2.h: Add a format for column YUV4:2:0 modes
Some of the Broadcom codec blocks use a column based YUV4:2:0 image
format, so add the documentation and defines for both 8 and 10 bit
versions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
popcornmix [Wed, 1 Apr 2020 10:22:44 +0000 (11:22 +0100)]
bcmgenet: Disable skip_umac_reset by default
Possible fixed upstream by 'net: bcmgenet: keep MAC in reset until PHY is up'
Signed-off-by: popcornmix <popcornmix@gmail.com>
Jim Quinlan [Mon, 15 Jan 2018 23:28:39 +0000 (18:28 -0500)]
dt-bindings: pci: Add DT docs for Brcmstb PCIe device
The DT bindings description of the Brcmstb PCIe device is described. This
node can be used by almost all Broadcom settop box chips, using
ARM, ARM64, or MIPS CPU architectures.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Phil Elwell [Thu, 6 Feb 2020 12:23:15 +0000 (12:23 +0000)]
of: overlay: Correct symbol path fixups
When symbols from overlays are added to the live tree their paths must
be rebased. The translated symbol is normally the result of joining
the fragment-relative path (with a leading "/") to the target path
(either copied directly from the "target-path" property or resolved
from the phandle). This translation fails when the target is the root
node (a common case for Raspberry Pi overlays) because the resulting
path starts with a double slash. For example, if target-path is "/" and
the fragment adds a node called "newnode", the label associated with
that node will be assigned the path "//newnode", which can't be found
in the tree.
Fix the failure case by explicitly replacing a target path of "/" with
an empty string.
Fixes:
d1651b03c2df ("of: overlay: add overlay symbols to live device tree")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 2 Mar 2020 14:42:23 +0000 (14:42 +0000)]
video: fbdev: bcm2708_fb: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 6 Jan 2020 16:04:30 +0000 (16:04 +0000)]
pinctrl: bcm2835: Remove gpiochip on error
A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix
the leak with the use of devm_gpiochip_add_data.
Fixes:
85ae9e512f43 ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 3 Feb 2020 17:30:46 +0000 (17:30 +0000)]
staging: vchiq_arm: Give vchiq children DT nodes
vchiq kernel clients are now instantiated as platform drivers rather
than using DT, but the children of the vchiq interface may still
benefit from access to DT properties. Give them the option of a
a sub-node of the vchiq parent for configuration and to allow
them to be disabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Luke Hinds [Wed, 22 Jan 2020 16:03:00 +0000 (16:03 +0000)]
Initialise rpi-firmware before clk-bcm2835
The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted
Platform Module) having been registered when it initialises; otherwise
it assumes there is no TPM. It has been observed on BCM2835 that IMA
is initialised before TPM, and that initialising the BCM2835 clock
driver before the firmware driver has the effect of reversing this
order.
Change the firmware driver to initialise at core_initcall, delaying the
BCM2835 clock driver to postcore_initcall.
See: https://github.com/raspberrypi/linux/issues/3291
https://github.com/raspberrypi/linux/pull/3297
Signed-off-by: Luke Hinds <lhinds@redhat.com>
Co-authored-by: Phil Elwell <phil@raspberrypi.org>
Stefan Wahren [Fri, 27 Dec 2019 10:40:56 +0000 (11:40 +0100)]
ARM: bcm: Backport BCM2711 support from upstream
Make the BCM2711 a different machine, but keep it in board_bcm2835.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Dave Stevenson [Tue, 18 Jun 2019 11:15:50 +0000 (12:15 +0100)]
staging: vchiq: Use the old dma controller for OF config on platform devices
vchiq on Pi4 is no longer under the soc node, therefore it
doesn't get the dma-ranges for the VPU.
Switch to using the configuration of the old dma controller as
that will set the dma-ranges correctly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Tue, 29 Jan 2019 16:13:25 +0000 (16:13 +0000)]
staging: vchiq_arm: Set up dma ranges on child devices
The VCHIQ driver now loads the audio, camera, codec, and vc-sm
drivers as platform drivers. However they were not being given
the correct DMA configuration.
Call of_dma_configure with the parent (VCHIQ) parameters to be
inherited by the child.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
popcornmix [Mon, 9 Sep 2019 14:49:56 +0000 (15:49 +0100)]
clk-raspberrypi: Allow cpufreq driver to also adjust gpu clocks
For performance/power it is beneficial to adjust gpu clocks with arm clock.
This is how the downstream cpufreq driver works
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Thu, 5 Sep 2019 16:59:14 +0000 (17:59 +0100)]
v3d_gem: Kick the clock so firmware knows we are using firmware clock interface
Setting the v3d clock to low value allows firmware to handle dvfs in case
where v3d hardware is not being actively used (e.g. console use).
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Fri, 23 Aug 2019 15:34:38 +0000 (16:34 +0100)]
v3d_drv: Handle missing clock more gracefully
Signed-off-by: popcornmix <popcornmix@gmail.com>
James Hughes [Thu, 31 Oct 2019 14:39:44 +0000 (14:39 +0000)]
net:phy:2711 Allow ethernet LED mode to be set via device tree
Add device tree entries and code to allow the specification of
the lighting modes for the LED's on the ethernet connector.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
net:phy:2711 Change the default ethernet LED actions
This should return default behaviour back to that of previous
releases.
Dave Stevenson [Wed, 6 Nov 2019 13:57:58 +0000 (13:57 +0000)]
staging: vchiq_arm: Register bcm2835-codec as a platform driver
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the V4L2 codec driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 6 Nov 2019 13:57:48 +0000 (13:57 +0000)]
staging: vchiq_arm: Register vcsm-cma as a platform driver
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the vcsm-cma driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Mon, 11 Nov 2019 20:18:08 +0000 (20:18 +0000)]
drm/v3d: Suppress all but the first MMU error
The v3d driver currently encounters a lot of MMU PTE exceptions, so
only log the first to avoid swamping the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Markus Proeller [Thu, 10 Oct 2019 17:12:36 +0000 (19:12 +0200)]
media: i2c: Add a driver for the Infineon IRS1125 depth sensor
The Infineon IRS1125 is a time of flight depth sensor that
has a CSI-2 interface.
Add a V4L2 subdevice driver for this device.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Thu, 10 Oct 2019 17:12:08 +0000 (19:12 +0200)]
dt-bindings: Add binding for the Infineon IRS1125 sensor
Adds a binding for the Infineon IRS1125 time-of-flight depth
sensor.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Stefan Wahren [Thu, 19 Sep 2019 18:45:30 +0000 (20:45 +0200)]
ARM: bcm: Switch board, clk and pinctrl to bcm2711 compatible
After the decision to use bcm2711 compatible for upstream, we should
switch all accepted compatibles to bcm2711. So we can boot with
one DTB the down- and the upstream kernel.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Dave Stevenson [Mon, 8 Feb 2021 11:48:35 +0000 (11:48 +0000)]
staging:bcm2835-camera: Fix the cherry-pick of AWB Greyworld
The cherry-pick of the patch that added the greyworld AWB mode
was incomplete. Fix it up.
Fixes:
b3ef481fe243 "staging: bcm2835-camera: Add greyworld AWB mode"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
John Cox [Fri, 6 Aug 2021 13:32:44 +0000 (14:32 +0100)]
media: v4l2: Add Greyworld AWB control name
Add name for greyworld to white_balance preset names.
This patch previously applied to v4l2-ctrl.c but that was split
and deleted.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Dave Stevenson [Fri, 6 Sep 2019 14:13:06 +0000 (15:13 +0100)]
staging: bcm2835-camera: Add greyworld AWB mode
This is mainly used for the NoIR camera which has no IR
filter and can completely confuse normal AWB presets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Fri, 6 Sep 2019 14:04:51 +0000 (15:04 +0100)]
v4l2: Add a Greyworld AWB mode.
Adds a simple greyworld white balance preset, mainly for use
with cameras without an IR filter (eg Raspberry Pi NoIR)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
David Plowman [Tue, 29 Jun 2021 13:38:23 +0000 (14:38 +0100)]
Documentation: devicetree: Add documentation for imx378 sensor
The imx378 sensor is compatible with the imx477 and shares common
device tree settings.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Lee Jackson [Fri, 27 Aug 2021 06:36:55 +0000 (14:36 +0800)]
media: i2c: imx519: Support for the Sony IMX519 sensor
dt-bindings: media: i2c: Add IMX519 CMOS sensor binding
Add YAML device tree binding for IMX519 CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: Add driver for IMX519 sensor
Adds a driver for the 16MPix IMX519 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4656x3496 10-bit @ 10fps
3840x2160 10-bit (cropped) @ 21fps
2328x1748 10-bit (binned) @ 30fps
1920x1080 10-bit (cropped/binned) @ 60fps
1280x720 10-bit (cropped/binned) @ 120fps
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Advertise embedded data node on media pad 1
This commit updates the imx519 driver to adverise support for embedded
data streams.
The imx519 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Lee Jackson <info@arducam.com>
media: i2c: imx519: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: Update imx519 Kconfig entry
Bring the IMX519 Kconfig declaration in line with the upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Naushir Patuck [Thu, 7 May 2020 14:50:54 +0000 (15:50 +0100)]
media: i2c: imx477: Support for the Sony IMX477 sensor
dt-bindings: media: i2c: Add IMX477 CMOS sensor binding
Add YAML device tree binding for IMX477 CMOS image sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: Add driver for Sony IMX477 sensor
Adds a driver for the 12MPix Sony IMX477 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
The following Bayer modes are currently available:
4056x3040 12-bit @ 10fps
2028x1520 12-bit (binned) @ 40fps
2028x1050 12-bit (cropped/binned) @ 50fps
1012x760 10-bit (scaled) @ 120 fps
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add support for adaptive frame control
Use V4L2_CID_EXPOSURE_AUTO_PRIORITY to control if the driver should
automatically adjust the sensor frame length based on exposure time,
allowing variable frame rates and longer exposures.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Return correct result on sensor id verification
The test should return -EIO if the register read id does not match
the expected sensor id.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Parse and register properties
Parse device properties and register controls for them using the V4L2
fwnode properties helpers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
media: i2c: imx477: Selection compliance fixes
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx477 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 16) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
This commit mirrors
543790f777ba1b3264c168c653db6d415e7c983f done for
the imx219 sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove auto frame length adjusting
The V4L2_CID_EXPOSURE_AUTO_PRIORITY was used to let the sensor control
frame length (effectively framerate) based on the requested exposure
time requested. Remove this feature as it is never used, and goes
against how V4L2 likes to handle exposure and vblank controls.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Add very long exposure control to the driver
Add support for very long exposures by using the exposure multiplier
register. Userland does not need to pass any additional controls to
enable long exposures, it simply requests a larger vblank to extend the
exposure control range appropriately.
Currently, since hblank is fixed, a maximum of approximately 124 seconds
of exposure time can be used. In a future change, hblank could also be
controlled in userland to give over 200 seconds of exposure time.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix crop height for 2028x1080 mode
The crop height for this mode was set at 2600 lines, it should be 2160
lines instead.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Replace existing 1012x760 mode
The existing 1012x760 120 fps mode has significant IQ problem using
the internal sensor scaler. Replace this mode with a 1332x990 120 fps
mode instead. This new mode has a smaller field of view, but does not
suffer from the bad IQ of the original mode.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove internal v4l2_mbus_framefmt from the state
The only field in this struct that is used is the format code, so
replace the struct with this single field.
Save the format code in imx477_set_pad_format() when setting up a new
mode so that imx477_get_pad_format() performs the right lookup.
Otherwise, this caused a bug where the mode lookup occurred on the
12-bit table rather than the 10-bit table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Remove unused function parameter
The struct imx477 *ctrl parameter is not used in the function
imx477_adjust_exposure_range(), so remove it.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Fix for long exposure limit calculations
Do not scale IMX477_EXPOSURE_OFFSET with the long exposure factor during
the limit calculations. This allows larger exposure times, and does seem to be
what the sensor is doing internally.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Extend driver to support imx378 sensor
The imx378 sensor is almost identical to the imx477 and can be
supported as a "compatible" sensor with just a few extra register
writes.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Fix framerates for 1332x990 mode
The imx477 driver's line length for this mode had not been updated to
the value supplied to us by the sensor manufacturer. With this
correction the sensor delivers the framerates that are expected.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow control of on-sensor DPC
A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.
This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Sensor should report RAW color space
Tested on Raspberry Pi running libcamera.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Add vsync trigger_mode parameter
trigger_mode == 0 (default) => no effect / no registers written
trigger_mode == 1 => source
trigger_mode == 2 => sink
This can be set e.g. in /boot/cmdline.txt as imx477.trigger_mode=N
Signed-off-by: Jonas Jacob <jonas.jacob@neocortexvision.com>
media: i2c: Update imx477 Kconfig entry
Bring the IMX477 Kconfig declaration in line with upstream entries.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
media: i2c: imx477: Correct minimum exposure lines
The minimum number of exposure lines value (IMX477_EXPOSURE_MIN) was
previously 20 but this is not correct. The datasheet is not completely
explicit, however the new value of 4 has been tested with all the
sensor modes supported by this driver, and matches the lowest exposure
value of 114us that could be achieved wtih Raspberry Pi's legacy
firmware driver.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: i2c: imx477: Allow dynamic horizontal blanking control
Currently, the V4L2_CID_HBLANK control is marked as read-only. Remove this
restriction and allow userland to modify the control if needed.
Set the maximum limit of the line length to 0xfff0.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Reset hblank on mode switch
Reset the hblank control to the minimum value on every mode switch. This is to
account for userland instances that do not yet control hblank, otherwise it
gets set to a non-optimal value.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: i2c: imx477: Do not unconditionally adjust hblank and vblank limits
On a mode change, only call imx477_set_framing_limits() to adjust the hblank
and vblank limits if the new mode is different from the existing mode. This
preserves any manual control values the user might have set.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Phil Elwell [Tue, 3 Sep 2019 17:17:25 +0000 (18:17 +0100)]
arch/arm64: Add Revision, Serial, Model to cpuinfo
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 3 Sep 2019 17:16:56 +0000 (18:16 +0100)]
arch/arm: Add model string to cpuinfo
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 9 Aug 2019 07:51:43 +0000 (08:51 +0100)]
net: bcmgenet: Workaround #2 for Pi4 Ethernet fail
Some combinations of Pi 4Bs and Ethernet switches don't reliably get a
DCHP-assigned IP address, leaving the unit with a self=assigned 169.254
address. In the failure case, the Pi is left able to receive packets
but not send them, suggesting that the MAC<->PHY link is getting into
a bad state.
It has been found empirically that skipping a reset step by the genet
driver prevents the failures. No downsides have been discovered yet,
and unlike the forced renegotiation it doesn't increase the time to
get an IP address, so the workaround is enabled by default; add
genet.skip_umac_reset=n
to the command line to disable it.
See: https://github.com/raspberrypi/linux/issues/3108
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Thu, 1 Aug 2019 15:41:20 +0000 (16:41 +0100)]
hid: usb: Add device quirks for Freeway Airmouse T3 and MX3
These wireless mouse/keyboard combo remote control devices specify
multiple "wheel" events in their report descriptors. The wheel events
are incorrectly defined and apparently map to accelerometer data, leading
to spurious mouse scroll events being generated at an extreme rate when
the device is moved.
As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask
feeding the extra wheel events to the input subsystem.
See: https://github.com/raspberrypi/firmware/issues/1189
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Thu, 9 May 2019 13:30:37 +0000 (14:30 +0100)]
drivers: char: add chardev for mmap'ing the RPiVid control registers
Based on the gpiomem driver, allow mapping of the decoder register
spaces such that userspace can access control/status registers.
This driver is intended for use with a custom ffmpeg backend accelerator
prior to a v4l2 driver being written.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
driver: char: rpivid: Destroy the legacy device on remove
The legacy name support created a new device that was never destroyed.
If the driver was unloaded and reloaded, it failed due to the
device already existing.
Fixes: "75f1d14 driver: char: rpivid - also support legacy name"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Clean up error handling use of ERR_PTR/IS_ERR
The driver used an unnecessary intermediate void* variable so it
only called ERR_PTR once to convert to the error value.
Switch to converting as the error arises to remove these intermediate
variables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Add error handling to the legacy device load
The return value from device_create for the legacy device was never
checked or handled. Add the required error handling.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix coding style whitespace issues.
Makes checkpatch happier.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpimem: Add SPDX licence header.
Stops checkpatch complaining.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Fix access to freed memory
The error path during probe frees the private memory block, and
then promptly dereferences it to log an error message.
Use the base device instead of the pointer to it in the private
structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
driver: char: rpivid: Remove legacy name support
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
driver: char: rpivid: Don't map more than wanted
Limit mappings to the permitted range, but don't map more than asked
for otherwise we walk off the end of the allocated VMA.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Eric Anholt [Thu, 2 May 2019 20:22:53 +0000 (13:22 -0700)]
drm/v3d: Clock V3D down when not in use.
My various attempts at re-enabling runtime PM have failed, so just
crank the clock down when V3D is idle to reduce power consumption.
Signed-off-by: Eric Anholt <eric@anholt.net>
drm/v3d: Plug dma_fence leak
The irq_fence and done_fence are given a reference that is never
released. The necessary dma_fence_put()s seem to have been
deleted in error in an earlier commit.
Fixes:
0b73676836b2 ("drm/v3d: Clock V3D down when not in use.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 12 Jul 2019 14:38:35 +0000 (15:38 +0100)]
i2c: bcm2835: Set clock-stretch timeout to 35ms
The BCM2835 I2C blocks have a register to set the clock-stretch
timeout - how long the device is allowed to hold SCL low - in bus
cycles. The current driver doesn't write to the register, therefore
the default value of 64 cycles is being used for all devices.
Set the timeout to the value recommended for SMBus - 35ms.
See: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 11 Jun 2019 16:38:28 +0000 (17:38 +0100)]
arm: bcm2835: Add bcm2838 compatible string.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Tue, 11 Jun 2019 10:42:03 +0000 (11:42 +0100)]
usbhid: call usb_fixup_endpoint after mangling intervals
Lets the mousepoll override mechanism work with xhci.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Fri, 10 Mar 2023 14:21:42 +0000 (14:21 +0000)]
usb: xhci: drop and add the endpoint context in xhci_fixup_endpoint()
Setting both the Drop and Add bits on the input context prevents the
corruption of split transactions seen with the BCM2711 XHCI controller,
which is a dwc3 variant.
This is a downstream feature that allows usbhid to restrict polling
intervals on mice and keyboards, and was only tested on a VL805 which
didn't complain about the fact the endpoint got added twice.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Wed, 11 Aug 2021 14:33:57 +0000 (15:33 +0100)]
usb: xhci: workaround for bogus SET_DEQ_PENDING endpoint state
See https://github.com/raspberrypi/linux/issues/3981
An unknown unsafe memory access can result in the ep_state variable
in xhci_virt_ep being trampled with a stuck SET_DEQ_PENDING state
despite successful completion of a Set TR Deq Pointer command.
All URB enqueue/dequeue calls for the endpoint will fail in this state
so no transfers are possible until the device is reconnected.
As a workaround, clear the flag if we see it set and issue a new Set
TR Deq command anyway - this should be harmless, as a prior Set TR Deq
command will only have been issued in the Stopped state, and if the
endpoint is Running then the controller is required to ignore it and
respond with a Context State Error event TRB.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Tue, 11 Jun 2019 10:33:39 +0000 (11:33 +0100)]
xhci: implement xhci_fixup_endpoint for interval adjustments
Must be called in a non-atomic context, after the endpoint
has been registered with the hardware via xhci_add_endpoint
and before the first URB is submitted for the endpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Tue, 11 Jun 2019 09:55:00 +0000 (10:55 +0100)]
usb: add plumbing for updating interrupt endpoint interval state
xHCI caches device and endpoint data after the interface is configured,
so an explicit command needs to be issued for any device driver wanting
to alter the polling interval of an endpoint.
Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be
called after calculating endpoint bandwidth requirements but before any
URBs are submitted.
If polling intervals are shortened, any bandwidth reservations are no
longer valid but in practice polling intervals are only ever relaxed.
Limit the scope to interrupt transfers for now.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Jonathan Bell [Tue, 14 May 2019 16:17:59 +0000 (17:17 +0100)]
net: genet: enable link energy detect powerdown for external PHYs
There are several warts surrounding bcmgenet_mii_probe() as this
function is called from ndo_open, but it's calling registration-type
functions. The probe should be called at probe time and refactored
such that the PHY device data can be extracted to limit the scope
of this flag to Broadcom PHYs.
For now, pass this flag in as it puts our attached PHY into a low-power
state when disconnected.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Phil Elwell [Wed, 27 Mar 2019 13:45:46 +0000 (13:45 +0000)]
bcmgenet: Better coalescing parameter defaults
Set defaults for TX and RX packet coalescing to be equivalent to:
# ethtool -C eth0 tx-frames 10
# ethtool -C eth0 rx-usecs 50
This may be something we want to set via DT parameters in the
future.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>