Vikas Manocha [Fri, 3 Jul 2015 01:29:43 +0000 (18:29 -0700)]
spi: cadence_qspi: move the sram partition in init
There is no need to re-configure sram partition for every read/write for
better full use of sram for read or write. This patch divides the half
sram for read & half for write once at initialization.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Vikas Manocha [Fri, 3 Jul 2015 01:29:42 +0000 (18:29 -0700)]
stv0991: configure device tree for cadence qspi & flash
This patch add the device tree entry for qspi controller & spi flash
memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Vikas Manocha [Fri, 3 Jul 2015 01:29:41 +0000 (18:29 -0700)]
stv0991: enable cadence qspi controller & spi flash
This patch does all the board configurations required to use the qspi
controller & attached spi flash memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Vikas Manocha [Fri, 3 Jul 2015 01:29:40 +0000 (18:29 -0700)]
stv0991: configure clock & pad muxing for qspi
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Vikas Manocha [Fri, 3 Jul 2015 01:29:39 +0000 (18:29 -0700)]
stv0991: remove define CONFIG_OF_SEPARATE from board file
CONFIG_OF_SEPARATE is default define with CONFIG_OF_CONTROL, removing
this define from the board file to avoid multiple definition warning.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Vikas Manocha [Fri, 3 Jul 2015 01:29:38 +0000 (18:29 -0700)]
stv0991: move OF_CONTROL config to defconfig
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Vikas Manocha [Fri, 3 Jul 2015 01:29:37 +0000 (18:29 -0700)]
stv0991: enable saving enrironment in spi flash
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Tom Rini [Wed, 1 Jul 2015 19:38:12 +0000 (15:38 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
Tom Rini [Wed, 1 Jul 2015 19:37:56 +0000 (15:37 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier
Angelo Dureghello [Sun, 21 Jun 2015 21:40:46 +0000 (23:40 +0200)]
spi: cf_qspi: fix clamp macro type check compilation warnings
Fix compilation warnings for redefined 'clamp' macro and non-uniform
clamp macro types.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Jagan Teki [Mon, 29 Jun 2015 18:18:31 +0000 (23:48 +0530)]
README: Remove CONFIG_SPI_FLASH_DATAFLASH help text
Since the help text is added in drivers/mtd/spi/Kconfig
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 29 Jun 2015 18:17:40 +0000 (23:47 +0530)]
README: Remove CONFIG_SPI_FLASH_BAR help text
Since the help text is added in drivers/mtd/spi/Kconfig
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 29 Jun 2015 18:02:17 +0000 (23:32 +0530)]
sf: Kconfig: Add SPI_FLASH_BAR entry
Added SPI_FLASH_BAR entry on Kconfig with help description
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 29 Jun 2015 17:06:18 +0000 (22:36 +0530)]
defconfig: Move CONFIG_SPI_FLASH_BAR from configs
This commit moves:
- CONFIG_SPI_FLASH_BAR
from include/configs/*.h into configs/*_defconfigs
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 29 Jun 2015 18:16:00 +0000 (23:46 +0530)]
README: Remove CONFIG_SPI_FLASH_MTD help text
Since the help text is added in drivers/mtd/spi/Kconfig
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sat, 27 Jun 2015 10:37:54 +0000 (16:07 +0530)]
spi: Kconfig: Add TEGRA20_SLINK entry
Added TEGRA20_SLINK entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Jagan Teki [Sat, 27 Jun 2015 10:34:05 +0000 (16:04 +0530)]
spi: Kconfig: Add TEGRA20_SFLASH entry
Added TEGRA20_SFLASH entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Jagan Teki [Sat, 27 Jun 2015 10:27:53 +0000 (15:57 +0530)]
spi: Kconfig: Add TEGRA114_SPI entry
Added TEGRA114_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Jagan Teki [Sat, 27 Jun 2015 10:13:27 +0000 (15:43 +0530)]
spi: Kconfig: Add ICH_SPI entry
Added ICH_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Jagan Teki [Sat, 27 Jun 2015 10:02:19 +0000 (15:32 +0530)]
spi: Kconfig: Add EXYNOS_SPI entry
Added EXYNOS_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Sat, 27 Jun 2015 09:53:07 +0000 (15:23 +0530)]
spi: Kconfig: Add FSL_QSPI entry
Added FSL_QSPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
Jagan Teki [Sat, 27 Jun 2015 09:51:36 +0000 (15:21 +0530)]
spi: Kconfig: Add FSL_ESPI entry
Added FSL_ESPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
Jagan Teki [Sat, 27 Jun 2015 08:47:06 +0000 (14:17 +0530)]
spi: Kconfig: Add FSL_DSPI entry
Added FSL_DSPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
Jagan Teki [Sat, 27 Jun 2015 17:07:00 +0000 (22:37 +0530)]
spi: Kconfig: Show dm-spi drivers if DM_SPI set
DM supported spi drivers are enbled only when DM_SPI enabled,
so added DM_SPI if condition in Kconfig to show thoese only
when it enabled.
Also re-order the config items as incresing alphabetic order.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sat, 27 Jun 2015 08:21:53 +0000 (13:51 +0530)]
spi: Makefile: Use object file alphabetic order
Use object files as incresing alphabetic order, so-that it's
easy for readability.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 23:11:11 +0000 (04:41 +0530)]
spi: Kconfig: Add TI_QSPI entry
Added TI_QSPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Fri, 26 Jun 2015 23:02:43 +0000 (04:32 +0530)]
spi: Kconfig: Add XILINX_SPI entry
Added XILINX_SPI entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Jagan Teki [Sat, 27 Jun 2015 17:05:14 +0000 (22:35 +0530)]
spi: Add Kconfig menu entry
Added Kconfig menu ... endmenu enties for spi support.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Masahiro Yamada [Tue, 30 Jun 2015 09:43:45 +0000 (18:43 +0900)]
ARM: UniPhier: add IDs for PH1-Pro5, ProXstream2, PH1-LD6b
This prepares for new SoCs support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 30 Jun 2015 09:27:01 +0000 (18:27 +0900)]
ARM: dts: UniPhier: re-license device tree files under GPLv2+/X11
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, the device trees for UniPhier
SoCs and boards have already been dual-licensed in Linux.
Follow this trend in U-boot too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 30 Jun 2015 09:27:00 +0000 (18:27 +0900)]
ARM: dts: UniPhier: sync device trees with the Linux kernel
This makes code diff much easier.
Device trees describe hardware attributes, which are independent
of software architecture. It generally makes sense to synchronize
them beyond software projects.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 30 Jun 2015 08:10:22 +0000 (17:10 +0900)]
ARM: UniPhier: drop special CONFIG_AUTOBOOT_ settings
There is no good reason to use a particular key to stop autobooting.
The default allows us to stop the autoboot with any key input.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Jagan Teki [Wed, 1 Jul 2015 15:52:19 +0000 (21:22 +0530)]
sf: Kconfig: Add SPI_FLASH_DATAFLASH entry
Added SPI_FLASH_DATAFLASH entry on Kconfig with help description.
data flash driver comes with good decription, hence moved the
same on to kconfig help decription.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Haikun Wang <haikun.wang@freescale.com>
Jagan Teki [Sat, 27 Jun 2015 17:12:35 +0000 (22:42 +0530)]
sf: Kconfig: Add SPI_FLASH_MTD entry
Added SPI_FLASH_MTD entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Jagan Teki [Sun, 28 Jun 2015 19:29:36 +0000 (00:59 +0530)]
sf: Kconfig: Update SPI_FLASH entry
Updated SPI_FLASH entry on Kconfig with depends on
and along with config help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 22:17:53 +0000 (03:47 +0530)]
common: Add CMD_SF Kconfig entry
Added Kconfig entry for CMD_SF.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sat, 27 Jun 2015 17:09:36 +0000 (22:39 +0530)]
sf: Add Kconfig menu entry
Added Kconfig menu ... endmenu enties for spi flash suppor
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 21:54:53 +0000 (03:24 +0530)]
README: Add CONFIG_SPI_FLASH_DATAFLASH description
This patch adds CONFIG_SPI_FLASH_DATAFLASH descrition on README
file for more readble for users.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sat, 27 Jun 2015 16:34:55 +0000 (22:04 +0530)]
sf: dataflash: Rename to CONFIG_SPI_FLASH_DATAFLASH
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 29 Jun 2015 08:47:32 +0000 (14:17 +0530)]
zynq: defconfig: Move CONFIG_OF_* to Kconfig
This commit moves:
- CONFIG_OF_CONTROL
- SPL_DISABLE_OF_CONTROL
from zynq_*_defconfig files into arch/arm/Kconfig "config ARCH_ZYNQ"
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Jagan Teki [Mon, 29 Jun 2015 08:46:30 +0000 (14:16 +0530)]
defconfig: Add CONFIG_OF_CONTROL in zynq_picozed
Enable FDT support for zynq_picozed board.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:38 +0000 (00:51 +0530)]
spi: Kconfig: Add Zynq SPI controller entry
Add Zynq SPI controller Kconfig entry.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:37 +0000 (00:51 +0530)]
spi: xilinx_spi: Add asm/io.h include file
This patch includes asm/io.h for readl and writel calls.
build errors:
drivers/spi/xilinx_spi.c: In function 'xilinx_spi_probe':
drivers/spi/xilinx_spi.c:119:2: warning: implicit declaration of function 'writel' [-Wimplicit-function-declaration]
drivers/spi/xilinx_spi.c: In function 'xilinx_spi_xfer':
drivers/spi/xilinx_spi.c:193:2: warning: implicit declaration of function 'readl' [-Wimplicit-function-declaration]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Jagan Teki [Mon, 29 Jun 2015 07:45:18 +0000 (13:15 +0530)]
dm: spi: xilinx_spi: Convert to driver model
This converts the xilinx spi driver to use the driver model.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:35 +0000 (00:51 +0530)]
dts: zynq: Enable spi1 for zc770_xm010 board
This patch enables spi1 for zynq zc770_xm010 board dts
Signed-off-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:34 +0000 (00:51 +0530)]
spi: zynq_spi: Add fdt support in driver
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:33 +0000 (00:51 +0530)]
dts: zynq: Add zynq spi controller nodes
This patch adds zynq spi controller nodes in zynq-7000.dtsi.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:32 +0000 (00:51 +0530)]
zynq: Kconfig: Enable dm spi and spi_flash
Enabled CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH for zynq soc.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:31 +0000 (00:51 +0530)]
dm: spi: zynq_spi: Convert to driver model
This converts the zynq spi driver to use the driver model.
Minimal functional changes like using meaningful name on
structure members wrt mainlined dm spi drivers.
- input_hz -> frequency
- req_hz -> freq
- base -> regs
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:30 +0000 (00:51 +0530)]
spi/sf: Minor cleanups
- Adjust tab spaces
- Add comments
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:29 +0000 (00:51 +0530)]
spi: davinci_spi: Driver cleanup
Arrange driver code in more readable format[1] for easy accessing
and readable.
[1] http://patchwork.ozlabs.org/patch/265683/
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Rex Chang <rchang@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:28 +0000 (00:51 +0530)]
spi: davinci_spi: Move header code to driver
Move the header code into driver for more readable and
easy to access it.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Rex Chang <rchang@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:27 +0000 (00:51 +0530)]
spi: xilinx_spi: Driver clean-up
- Zap unneeded macros
- Re-arrange the code
- Removed __attribute__((weak))
- Replace __func__ macro with func names to save macro transition.
- Re-arranged comment lines.
- Arrange driver code in more readable format[1]
[1] http://patchwork.ozlabs.org/patch/265683/
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:26 +0000 (00:51 +0530)]
spi: xilinx_spi: Move header code to driver
Move the header code into driver for more readable and
easy to access it.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:25 +0000 (00:51 +0530)]
spi: Zap oc_tiny_spi driver
Zap oc_tiny_spi driver since the boards used this driver
is no longer been active.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Jagan Teki [Fri, 26 Jun 2015 19:21:24 +0000 (00:51 +0530)]
spi: Zap ftssp010_spi driver
Zap ftssp010_spi driver since the boards used this driver
is no longer been active.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Axel Lin <axel.lin@ingics.com>
Jagan Teki [Fri, 26 Jun 2015 19:21:23 +0000 (00:51 +0530)]
spi: Zap andes_spi driver
Zap andes_spi driver since the boards used this driver
is no longer been active.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Alexey Brodkin [Wed, 1 Jul 2015 13:47:42 +0000 (16:47 +0300)]
board: axs103 - add maintainer information
Looks like I forgot to add myself as a maintainer for AXS103 defconfig.
Fixing this now.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>
Alexey Brodkin [Mon, 18 May 2015 13:56:26 +0000 (16:56 +0300)]
arc: significant cache rework
[1] Align cache management functions to those in Linux kernel. I.e.:
a) Use the same functions for all cache ops (D$ Inv/Flush)
b) Split cache ops in 3 sub-functions: "before", "lineloop" and
"after". That way we may re-use "before" and "after" functions for
region and full cache ops.
[2] Implement full-functional L2 (SLC) management. Before SLC was
simply disabled early on boot. It's also possible to enable or disable
L2 cache from config utility.
[3] Disable/enable corresponding caches early on boot. So if U-Boot is
configured to use caches they will be used at all times (this is useful
in partucular for speed-up of relocation).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Mon, 13 Apr 2015 10:37:05 +0000 (13:37 +0300)]
arc: implement slave cores kick-start for Linux kernel
With new SMP-enabled CPUs with ARC HS38 cores and corresponding support
in Linux kernel it's required to add basic SMP support in U-Boot.
Currently we assume the one and only core starts execution after
power-on. So most of things in U-Boot is handled in UP mode.
But when U-Boot is used for loading and starting Linux kernel right
before jumping to kernel's entry point U-Boot:
[1] Sets all slave cores to jump to the same address [kernel's entry
point]
[2] Really starts all slav cores
In ARC's implemetation of SMP in Linux kernel all cores are supposed to
run the same start-up code. But only core with ID 0 (master core)
processes further while others are looping waiting for master core to
complete some initialization.
That means it's safe to un-pause slave cores and let them execute kernel
- they will wait for master anyway.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Tom Rini [Mon, 29 Jun 2015 21:22:01 +0000 (17:22 -0400)]
Prepare v2015.07-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Haikun Wang [Mon, 29 Jun 2015 09:15:52 +0000 (17:15 +0800)]
sf: update sst25wf040b flash params
sst25wf040b doesn't support Auto Address Increment Programming command.
Remove SST_WR flag.
Signed-off-by: Haikun Wang <B53464@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Heiko Schocher [Mon, 27 Apr 2015 05:42:07 +0000 (07:42 +0200)]
mtd, spi: Check if flash pointer is used
If flash pointer is used free it, before probing a new
flash and storing it in flash.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Heiko Schocher [Mon, 27 Apr 2015 05:42:06 +0000 (07:42 +0200)]
spi, sf: Use offset and size in sf cmd from mtdpartition
With this patch, it is possible to get the offset and size information
from the mtdpartiton setting in "mtdparts", similiar to the
"nand" commandos.
=> sf
sf - SPI flash sub-system
Usage:
sf probe [[bus:]cs] [hz] [mode] - init flash device on given SPI bus
and chip select
sf read addr offset|partition len - read `len' bytes starting at
`offset' to memory at `addr'
sf write addr offset|partition len - write `len' bytes from memory
at `addr' to flash at `offset'
sf erase offset|partition [+]len - erase `len' bytes from `offset'
`+len' round up `len' to block size
sf update addr offset|partition len - erase and write `len' bytes from memory
at `addr' to flash at `offset'
=>
for example "env" is defined in mtdparts:
=> sf read
13000000 env
device 0 offset 0xd0000, size 0x10000
SF: 65536 bytes @ 0xd0000 Read: OK
zynq-uboot> mtdparts add nor0 0x10000@0x0 env
zynq-uboot> sf erase env 0x10000
SF: 65536 bytes @ 0x0 Erased: OK
zynq-uboot> sf write 0x100 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Written: OK
zynq-uboot> sf read 0x40000 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Read: OK
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Heiko Schocher [Mon, 27 Apr 2015 05:42:05 +0000 (07:42 +0200)]
mtd, nand: Move common functions from cmd_nand.c to common place
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Daniel Schwierzeck [Mon, 27 Apr 2015 05:42:04 +0000 (07:42 +0200)]
mtd, spi: Add MTD layer driver
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=
bb246819cdc90493dd7089eaa51b9e639765cced
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Haikun Wang [Sat, 27 Jun 2015 16:21:05 +0000 (21:51 +0530)]
defconfig: ls1021a: Add OF_CONTROL and DM support
PI and QSPI only work when boot from QSPI on ls1021a.
This patch only enable options in qspi boot defconfig.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Haikun Wang [Sat, 27 Jun 2015 16:16:13 +0000 (21:46 +0530)]
arm: ls102xa: Enable Driver Model SPI for ls1021atwr
Enable Driver Model SPI for ls1021atwr board.
DSPI and QSPI only be enabled when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Haikun Wang [Mon, 29 Jun 2015 07:38:46 +0000 (13:08 +0530)]
arm: ls102xa: Enable Driver Model SPI for ls1021aqds
Enable Driver Model SPI for ls1021aqds board.
DSPI and QSPI is enabled only when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Haikun Wang [Fri, 26 Jun 2015 11:30:41 +0000 (19:30 +0800)]
dm: ls1021aqds: dts: Use "spi_dataflash" driver instead of "spi_flash_std" for DSPI flash
The type of DSPI flash on ls1021aqds is AT45DB021, it has specail
commands and page-size.
Use the special spi flash driver instead of "spi_flash_std" driver.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Haikun Wang [Fri, 26 Jun 2015 11:30:27 +0000 (19:30 +0800)]
dm: sf: Add Atmel DataFlash spi flash driver
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l
82000000 45444342 20000
=> sf write
82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read
83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b
82000000 83000000 42000
Total of 270336 byte(s) were the same
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chakra Divi <cdivi@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tom Rini [Sun, 28 Jun 2015 20:31:32 +0000 (16:31 -0400)]
Merge git://git.denx.de/u-boot-marvell
Kevin Smith [Mon, 18 May 2015 16:09:46 +0000 (16:09 +0000)]
db-88f6820-gp.h: Load data blobs into lower memory
By default on this platform, u-boot loads data into high memory
in the range of 0x7Fxxxxxx, which generates a data abort when the
kernel tries to read it. Config the u-boot environment to load
the device tree and initrd image into lower memory to make them
accessible to the kernel.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Kevin Smith [Mon, 18 May 2015 16:09:45 +0000 (16:09 +0000)]
mv-common.h: Include support for device trees
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Ian Campbell [Fri, 26 Jun 2015 18:42:24 +0000 (19:42 +0100)]
Revert "sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory"
This reverts commit
f76eba38b3eda905ff3bdc18dd1240d3dcbc6e5a.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
Joe Hershberger [Mon, 22 Jun 2015 21:15:30 +0000 (16:15 -0500)]
Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Joe Hershberger [Mon, 22 Jun 2015 21:15:29 +0000 (16:15 -0500)]
Move default y configs out of arch/board Kconfig
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Joe Hershberger [Mon, 22 Jun 2015 21:15:28 +0000 (16:15 -0500)]
a3m071: Add needed dependency on LIB_RAND
Boards using link-local need lib rand.
When link-local is moved to Kconfig, this dependency will be described
there.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 22 Jun 2015 21:15:26 +0000 (16:15 -0500)]
common: Add the CMD_ENV_EXISTS config to Kconfig
This command needs to exist in the Kconfig so that it can be moved from
the config_cmd_default.h.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 22 Jun 2015 21:15:25 +0000 (16:15 -0500)]
common: Fix comment for saveenv in Kconfig
The help for this was simply copied from another command.
Update it to reflect the command.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 22 Jun 2015 21:15:24 +0000 (16:15 -0500)]
mtd: spi: Add the SPI_FLASH config to Kconfig
This config needs to be available in the Kconfig to allow it to be
removed from arch defaults.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Fri, 19 Jun 2015 21:39:41 +0000 (23:39 +0200)]
mmc: bcm2835_sdhci: Restore original delay behavior
Patch
33fe2fb8df01647f97a7bce96a1c7781a7f6d253 titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.
Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jakub KiciĆski <moorray3@wp.pl>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
Tom Rini [Fri, 19 Jun 2015 18:21:32 +0000 (14:21 -0400)]
Merge git://git.denx.de/u-boot-usb
Heiko Schocher [Mon, 15 Jun 2015 12:57:15 +0000 (14:57 +0200)]
siemens,am33x,thuban: rename dxr2 to thuban
Update new naming scheme.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Mon, 15 Jun 2015 12:56:41 +0000 (14:56 +0200)]
siemens,am33x,rastaban: add rastaban config
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Chris Packham [Fri, 19 Jun 2015 08:25:59 +0000 (20:25 +1200)]
README: Describe CONFIG_SYS_NO_FLASH
Unlike most configuration options defining this actually disables
support for a feature (parallel flash). Eventually the logic behind this
should probably be flipped so that '#ifndef CONFIG_SYS_NO_FLASH' becomes
'#ifdef CONFIG_HAS_PARALLEL_FLASH' but for now lets document the
existing behaviour.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Lokesh Vutla [Tue, 16 Jun 2015 15:06:05 +0000 (20:36 +0530)]
ARM: BeagleBoard-X15: Enable VTT regulator
BeagleBoard-X15 uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Mugunthan V N [Tue, 16 Jun 2015 14:53:39 +0000 (20:23 +0530)]
am43xx_evm: add eth boot support
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Mugunthan V N [Tue, 16 Jun 2015 14:53:38 +0000 (20:23 +0530)]
am43xx_evm: add usb host boot support
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 16 Jun 2015 14:53:37 +0000 (20:23 +0530)]
am43xx: Update CONFIG_SPL_TEXT_BASE
With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon). Prior silicon is OK using this address as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Nishanth Menon [Tue, 16 Jun 2015 13:29:01 +0000 (08:29 -0500)]
ARM: DRA7: Change configuration to prevent DDR reset control from EMIF
DRA7/AM57xx devices can be operated in many different configurations.
When the SoC is supposed to support a configuration where low power mode
state may involve the SoC completely powered off and DDR is in self
refresh, SoC EMIF controller should not be the master of the reset
signal and an external entity might be in control of things.
The default configuration of Linux on TI evms involve not powering off
the voltage rails (due to various reasons including reliability concerns)
and must not allow DDR reset to be controlled by EMIF. On platforms
where external entity might control the reset signal, this configuration
will be a "dont care".
Fixes:
536d87470869 ("ARM: DRA7: Update DDR IO registers")
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Guillaume GARDET [Tue, 16 Jun 2015 13:00:10 +0000 (15:00 +0200)]
ti: omap4: remove CONFIG_SPL_EXT_SUPPORT from ti_omap4_common.h since it is now in ti_armv7_common.h
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Guillaume GARDET [Tue, 16 Jun 2015 13:00:09 +0000 (15:00 +0200)]
ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)
Tested on Pandaboard (rev. A3) and Beagleboard xM (rev. B).
Compilation tested on TI armv7 boards and OMAP boards from other vendors.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 16 Jun 2015 12:59:34 +0000 (14:59 +0200)]
arm, am33xx: update for siemens am335x based boards
updates for the siemens am335x based boards:
- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
Leds can now be defined in Environment
- add generic env based dfu button
Which gpio is used for the dfu button can be defined
through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Paul Kocialkowski [Mon, 15 Jun 2015 19:35:05 +0000 (21:35 +0200)]
common: cmd_part: start and size sub-commands introduction
This introduces the part start and part size sub-commands. The purpose of these
is to store the start block and size of a partition in a variable, given the
device and partition number.
This allows reading raw data that fits a single partition more easily.
For instance, this could be used to figure out the start block and size of a
kernel partition when a partition table is present, given the partition number.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Stephen Warren <swarren@nvidia.com>
[trini: Change "%lx" to LBAF]
Signed-off-by: Tom Rini <trini@konsulko.com>
Paul Kocialkowski [Mon, 15 Jun 2015 19:35:04 +0000 (21:35 +0200)]
common: cmd_part: Proper alignment
This fixes a misaligned declaration.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Vitaly Andrianov [Mon, 15 Jun 2015 12:54:15 +0000 (08:54 -0400)]
keystone2: use correct EFUSE_BOOTROM fileds to configure speed
The get_max_arm_speed() and get_max_dev_speed() used wrong register
fields to get the maximum speeds. This commit fixes the bug.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Hans de Goede [Thu, 18 Jun 2015 20:34:34 +0000 (22:34 +0200)]
usb: kbd: Disable idle input reports when we do not need them
When we're polling and thus handling key-repeat in software, make sure
to disable idle reports, some keyboards may have these enabled by default
messing up our software keyrepeat.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Thu, 18 Jun 2015 20:34:33 +0000 (22:34 +0200)]
usb: ehci: Properly deal with data toggle for interrupt endpoints
Without this we loose every other interrupt packet. We never noticed this
because with keyboards the packets which we were loosing would normally
be key release packets.
But now that we do keyrepeat in software instead of relying on the hid
idle functionality, missing a release will result in key repeat triggering.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Wed, 10 Jun 2015 15:04:04 +0000 (17:04 +0200)]
usb.h: Always declare usb function prototypes
There is no harm in declaring the function prototypes even if nothing
implements them, and when CONFIG_DM_USB=y the various usb functions are
available regardless of any controller drivers being enabled.
This fixes compile warnings due to missing prototypes on ARCHs where
the ARCH Kconfig always enables CONFIG_DM_USB and various usb drivers.
One could argue that in the case of no controllers CONFIG_DM_USB should not
be set, but this problem is typically seen during bringup of boards which
do actually have usb controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>