platform/kernel/linux-rpi.git
4 years agoscripts: build-rpi3-arm64.sh, mkbootimg_rpi3.sh: Add modules
Seung-Woo Kim [Mon, 26 Mar 2018 03:35:11 +0000 (12:35 +0900)]
scripts: build-rpi3-arm64.sh, mkbootimg_rpi3.sh: Add modules

Add modules support on build scrip and image script.

Change-Id: I007d7ca940152506c856523e35adf4519248d2b5
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoscripts: mkbootimg_rpi3.sh: Install each rpi firmware and config.txt
Seung-Woo Kim [Mon, 26 Mar 2018 01:43:15 +0000 (10:43 +0900)]
scripts: mkbootimg_rpi3.sh: Install each rpi firmware and config.txt

After renaming config.txt for 64bit, mkbootimg_rpi3.sh is broken.
Fix to install each rpi firmware and config.txt considering changed
file name.

Change-Id: I907c1b6a8dc499da1e2f0364f9404a82a244e194
Fixes: 0979ebb94710 ("rpi3: config: rename config.txt to identify 64bit")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoscripts: mkbootimg_rpi3.sh: Change image size fitted to partition
Seung-Woo Kim [Mon, 26 Mar 2018 01:37:39 +0000 (10:37 +0900)]
scripts: mkbootimg_rpi3.sh: Change image size fitted to partition

From partitioning script of rpi3, boot partition is 64MiB. Change
image size fitted to the partition.

The partitioning script is on below link:
https://review.tizen.org/git/?p=platform/kernel/u-boot.git;a=blob_plain;f=scripts/tizen/sd_fusing_rpi3.sh;hb=refs/heads/tizen

Change-Id: Ia95c392235fe712bc1345078c64d07f6567fcbcb
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agopackaging: Add arm 32bit build
Seung-Woo Kim [Tue, 20 Mar 2018 02:11:31 +0000 (11:11 +0900)]
packaging: Add arm 32bit build

Add arm 32bit build.

Note: packaging is done with config.txt for 32bit.

Change-Id: Icf7e76523db3bb83fbd3d0bb6153157a64e62d93
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoarm: tizen_bcm2709_defconfig: enable sync file validation framework
Inki Dae [Wed, 21 Mar 2018 23:01:47 +0000 (08:01 +0900)]
arm: tizen_bcm2709_defconfig: enable sync file validation framework

Vulcan DDK will use this interface to create a fence and
increase timeline value of the fence.

Change-Id: I13c3f2442d26841e715dd01583d23f02b670679e
Signed-off-by: Inki Dae <inki.dae@samsung.com>
4 years agoarm64: tizen_bcmrpi3_defconfig: enable sync file validation framework
Inki Dae [Mon, 19 Mar 2018 06:54:24 +0000 (15:54 +0900)]
arm64: tizen_bcmrpi3_defconfig: enable sync file validation framework

Vulcan DDK will use this interface to create a fence and
increase timeline value of the fence.

Change-Id: Ib72ae7f591d4795eb9b0bdd51f742ae45ac954c2
Signed-off-by: Inki Dae <inki.dae@samsung.com>
4 years agorpi3: config: add config.txt for 32bit
Seung-Woo Kim [Mon, 19 Mar 2018 02:20:12 +0000 (11:20 +0900)]
rpi3: config: add config.txt for 32bit

Add config.txt for 32bit.

Note: It is for rpi3 32bit and rpi2, and in 32bit, there is no
atf implementation, so booting is done with u-boot.bin instead of
u-boot-spl.bin.

Change-Id: I556bb729f8be4a892f824d650b7935cd18efed20
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agorpi3: config: rename config.txt to identify 64bit
Seung-Woo Kim [Mon, 19 Mar 2018 01:45:41 +0000 (10:45 +0900)]
rpi3: config: rename config.txt to identify 64bit

Rename config.txt to config_64bit.txt to identify 64bit.

Note: The rpm packaging should be done as config.txt because the
name is used from bootcode.bin.

Change-Id: I41ca9c90673d2ee747b326627bced12e2284f1b8
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM: configs: add tizen_bcm2709_defconfig
Seung-Woo Kim [Wed, 21 Feb 2018 06:27:31 +0000 (15:27 +0900)]
ARM: configs: add tizen_bcm2709_defconfig

Add tizen_bcm2709_defconfig to support rpi2 and rpi3 32bit for
tizen.

Note: the defconfig is based on bcm2709_defconfig with tizen
features and less module options to fit 20MB modules size.

Change-Id: I19cd4961dbc2ce6fd60961aeac0cd56ed20b1527
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM: dts: bcm2809-rpi-2-b: enable display, touch, audio, spi and i2c
Seung-Woo Kim [Wed, 17 Jan 2018 09:35:52 +0000 (18:35 +0900)]
ARM: dts: bcm2809-rpi-2-b: enable display, touch, audio, spi and i2c

On RPI dt, several devices are enabled with overlay dt. Enable dsi,
hdmi, touchscreen, audio, spi and i2c devices without overlay from
rpi2 dt for Tizen kernel like rpi3.

Change-Id: I3e6f5dcd000a6c01d9a0c740a87ef28a41f3eb22
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable MMC_BCM2835_MMC config
Jaehoon Chung [Wed, 21 Feb 2018 06:00:33 +0000 (15:00 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable MMC_BCM2835_MMC config

Enable older bcm2835 driver instead of latest bcm2835 driver.
Before enable MMC_BCM2835_MMC config, Wifi doesn't work.
(Because SDIO interface didn't initialized.)

Change-Id: I53b5f276e4f57612a0e8af03544d2ae82c75b1ef
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agousb: dwc_otg: remove wrong memory accesses found by kasan
Seung-Woo Kim [Wed, 17 Jan 2018 01:29:01 +0000 (10:29 +0900)]
usb: dwc_otg: remove wrong memory accesses found by kasan

dwc_otg_hcd_is_bandwidth_allocated() requres ep_hcpriv pointer,
but passed parameter is double pointer and it cuases bad memory
access. Remove the wrong memory accesses.

Change-Id: I8292613f16fbf91ed9736b2a97e4afdb3bbbccec
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Sync with .config with v4.14.y
Jaehoon Chung [Fri, 5 Jan 2018 02:01:43 +0000 (11:01 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Sync with .config with v4.14.y

After updating to v4.14.y rebase, sync with .config.

Change-Id: I107539bb11b9e717e68023973a2bb2613aafc007
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable bcm2835-v4l2
Hackseung Lee [Wed, 6 Dec 2017 08:28:08 +0000 (17:28 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable bcm2835-v4l2

Enable bcm2835-v4l2 driver as dynamic kernel module.

Change-Id: I0a4cd562311fe6c41935b5376ce7fc94fab7b4b1
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
[sw0312.kim: apply config with bcm2835-v4l2 mmal message struct backported version]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable crypt-related configs
Junghoon Kim [Mon, 20 Nov 2017 05:56:07 +0000 (14:56 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable crypt-related configs

Enable crypt-related configs in order to support file system encryption.

Change-Id: Ib5d887db29d8431996f8acaa563ae67f159e0e4b
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>
4 years agoARM64: dts: bcm2710-rpi-3-b : add memory reserve
egukim [Tue, 4 Jul 2017 04:53:36 +0000 (13:53 +0900)]
ARM64: dts: bcm2710-rpi-3-b : add memory reserve

add memory reserve for rpi3(64bit) secure OS

Change-Id: I346a2d7c1afc0441ab4655592f3d81836a106f94
Signed-off-by: eunggu kim <egukim@dignsys.com>
4 years agoARM64: dts: bcm2710: add psci device node
egukim [Mon, 3 Jul 2017 05:06:47 +0000 (14:06 +0900)]
ARM64: dts: bcm2710: add psci device node

This patch changes the enable-method from 'spin-table' to
'PSCI (Power State Coordination Interface)' in order to control
the cpu state such as cpu up/down.

Change-Id: I92eaa95cbccbd86f6067bc9977acc45813703cad
Signed-off-by: eunggu kim <egukim@dignsys.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Enable TEE Driver
egukim [Mon, 3 Jul 2017 05:00:28 +0000 (14:00 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Enable TEE Driver

Set config CONFIG_TEE, CONFIG_OPTEE for enable optee kernel driver

Change-Id: Ib35167d8337126886b2bef03acf3aef6163d61ae
Signed-off-by: Eunggu kim <egukim@dignsys.com>
4 years agoARM64: dts: rpi3: Add optee node
egukim [Mon, 3 Jul 2017 04:55:37 +0000 (13:55 +0900)]
ARM64: dts: rpi3: Add optee node

Add device node for optee kernel driver. This based on
https://github.com/linaro-swg/linux/commit/a3d16523b5c3bd3c21e2009f2af0901b0d6d09dd

Change-Id: I9cc6d97354897b4656b02744076efd91889d7630
Signed-off-by: Joakim Bech <joakim.bech@linaro.org>
[egukim: modified commit from linaro-swg/linux of github]
Signed-off-by: Eunggu kim <egukim@dignsys.com>
4 years agomisc: tizen-inform-reboot: resolve sync failure about reboot parameter
Junghoon Kim [Tue, 17 Oct 2017 05:43:04 +0000 (14:43 +0900)]
misc: tizen-inform-reboot: resolve sync failure about reboot parameter

Currently, writing reboot paramter into INFORM partition fails
infrequently.

Resolve this issue by calling sync_filesystem function so that it writes
out and waits upon all dirty data associated with this superblock.

Change-Id: Ic62df0c3c4e565ca7211eb85661ead6979f0ad8d
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>
4 years agomisc: make sure Tizen notifier is executed before reset
Łukasz Stelmach [Fri, 29 Sep 2017 13:24:05 +0000 (15:24 +0200)]
misc: make sure Tizen notifier is executed before reset

In case of RaspberryPi the CPU is reset by watchdog triggered from
the bcm2835_restart_notifier_call function. Tizen notifier needs higher
priority to be called before the watchdog.

Change-Id: Ia7f6d895f6f40d1a9b4e57ad41b5bdb55c94f4f2
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: add i2c-stub to module
kibak.yoon [Fri, 13 Oct 2017 05:20:48 +0000 (14:20 +0900)]
ARM64: tizen_bcmrpi3_defconfig: add i2c-stub to module

We need a test method for the i2c driver and framework on RPI3.
And using a fake device is more convenient than a physical hardware device.
Therefore it would be good to enable i2c-stub for testing i2c feature on RPI3.
This will be used for testing purposes only.

Change-Id: I279bccabf709631130eae7b257bec6275b6acba0
Signed-off-by: kibak.yoon <kibak.yoon@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: support Western european languages
Inki Dae [Wed, 27 Sep 2017 08:41:16 +0000 (17:41 +0900)]
ARM64: tizen_bcmrpi3_defconfig: support Western european languages

Add Western european language support.

This language support is required for mounting vfat filesystem with default
language set on USB storage.

Change-Id: Ibf479d540a0df8502cae5af0dc242b1cdce3d6c8
Signed-off-by: Inki Dae <inki.dae@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable TIZEN_INFORM_REBOOT with inform path
Junghoon Kim [Tue, 22 Aug 2017 04:46:05 +0000 (13:46 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable TIZEN_INFORM_REBOOT with inform path

Reboot parameter passing is required for determining booting mode for
rpi3.

Activate Tizen reboot parameter passing feature with inform file path.

Change-Id: I67a7c24548dda8e8dd860fa25b2f558dadb83cf5
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>
4 years agomisc: add Tizen reboot notifier for passing reboot parameter
Junghoon Kim [Mon, 21 Aug 2017 02:04:32 +0000 (11:04 +0900)]
misc: add Tizen reboot notifier for passing reboot parameter

To determine booting mode (e.g, fota or recovery) in u-boot side, reboot
parameter should be passed through inform partition.

Add Tizen reboot notifier for passing reboot parameter.

Change-Id: I5830dcf58ec6905b0bc382599aa9ff1251f817d8
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable uprobes
Karol Lewandowski [Fri, 8 Sep 2017 10:13:15 +0000 (12:13 +0200)]
ARM64: tizen_bcmrpi3_defconfig: enable uprobes

This functionality is needed for D-Bus Observability Tools
(developed in platform/tools/bcc).

uprobes allows monitoring userspace processes with eBPF
without code modification.

Change-Id: Ic163b72a8315602b89059f36615b88da892aeb0d

4 years agoInput: rpi_ft5406 - add enable sysfs attribute
KwangCheol Lee [Mon, 11 Sep 2017 05:09:08 +0000 (14:09 +0900)]
Input: rpi_ft5406 - add enable sysfs attribute

Add enable sysfs attribute for disable/enable the touchscreen input.
This feature is required to turn the touch screen display on or off.

Change-Id: I4d5250c32cc2118f0f19a8a3cfb76ea8574f6937
Signed-off-by: KwangCheol Lee <kclee@dignsys.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable BPF and KPROBES
Maciej Slodczyk [Fri, 8 Sep 2017 12:56:42 +0000 (14:56 +0200)]
ARM64: tizen_bcmrpi3_defconfig: enable BPF and KPROBES

Enable BPF and KPROBES config options.

This functionality is needed for D-Bus Observability Tools,
eBPF (http://www.brendangregg.com/ebpf.html).

Change-Id: I2415ca28695e212ee1d02dd1480613cad8a5455c
Signed-off-by: Maciej Slodczyk <m.slodczyk2@partner.samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: synchronize the defconfig with pwm
Seung-Woo Kim [Mon, 11 Sep 2017 05:58:06 +0000 (14:58 +0900)]
ARM64: tizen_bcmrpi3_defconfig: synchronize the defconfig with pwm

It synchronizes the defconfig with pwm backlight to fix the commit
d1b5d090a9f8 ("ARM64: tizen_bcmrpi3_defconfig: enable the RPI touchscreen LCD")
because PWM config option added more config options to backlight.

Change-Id: Ie831a2601807a1f9ba729cf64fb98449147ed018
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agodrm/vc4: Workaround for crtc scanout device problem
Hoegeun Kwon [Thu, 7 Sep 2017 07:24:56 +0000 (16:24 +0900)]
drm/vc4: Workaround for crtc scanout device problem

Currently, the crtc device does not start a scanout, the time of
vblank is always calculated as future value. As a workaround, always
change vpos to a positive number.

Change-Id: I02527a0cfbd03d7713fa992d8ee039ffc8e0c5de
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
4 years agoARM64: dts: bcm2710-rpi-3-b: add DT support for DRM relevant devices
KwangCheol Lee [Mon, 7 Aug 2017 07:33:36 +0000 (16:33 +0900)]
ARM64: dts: bcm2710-rpi-3-b: add DT support for DRM relevant devices

Add DTs to support the official RPI touchscreen LCD.

Change-Id: Ibf3b17bfe5d1f0bbe55f941018a489899e8ea9ef
Signed-off-by: KwangCheol Lee <kclee@dignsys.com>
4 years agoBCM270X: Enable the DSI panel node in the VC4 overlay.
Eric Anholt [Thu, 2 Jun 2016 22:09:35 +0000 (15:09 -0700)]
BCM270X: Enable the DSI panel node in the VC4 overlay.

Change-Id: I46fdcdb53b79bd4f0db5022a415f6d1b9faf28e9
Signed-off-by: Eric Anholt <eric@anholt.net>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable the RPI touchscreen LCD
KwangCheol Lee [Mon, 7 Aug 2017 07:31:00 +0000 (16:31 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable the RPI touchscreen LCD

Enable following configurations for the official RPI touchscreen LCD.
+ TOUCHSCREEN_RPI_FT5406
+ I2C_GPIO
+ DRM_PANEL_RASPBERRYPI_TOUCHSCREEN
+ BACKLIGHT_RPI

Change-Id: I4c11ef34ea87ddeb120a5bc685905dffb5a8654c
Signed-off-by: KwangCheol Lee <kclee@dignsys.com>
4 years agoARM: dts: bcm2710-rpi-3-b: enable spi0 device node
Inki Dae [Tue, 5 Sep 2017 03:09:36 +0000 (12:09 +0900)]
ARM: dts: bcm2710-rpi-3-b: enable spi0 device node

Enable spi0 device node.

This patch is required to create spidev node which is used
by user space to control spi.

Change-Id: I8dec8288f6b35f628b178e0056d664b96f18ac4b
Signed-off-by: Inki Dae <inki.dae@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable SQUASHFS
Seung-Woo Kim [Wed, 30 Aug 2017 02:59:40 +0000 (11:59 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable SQUASHFS

To support compressed readonly image from Tizen, squashfs will be
used. Enable SQUASHFS and realted configuration. For better
performance, also SQUASHFS_DECOMP_MULTI_PERCPU and
SQUASHFS_4K_DEVBLK_SIZE options are set.

Change-Id: I8d7fb37f8b2bbe102fedc6c9d7d9c4c242d6ec32
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable SMACK_NETFILTER
Seung-Woo Kim [Tue, 29 Aug 2017 05:56:16 +0000 (14:56 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable SMACK_NETFILTER

On Tizen, nether service is failed because security smack netfilter
related configs are not enabled. So, enable related configs
including CONFIG_NETWORK_SECMARK, and CONFIG_SECURITY_SMACK_NETFILTER
and others.

Change-Id: Ia886ba9d5dd9bc559633acf3066818e57551f8f4
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM: dts: bcm2710-rpi-3-b : Change audio node status as "okay"
Lee Hackseung [Thu, 10 Aug 2017 06:48:39 +0000 (15:48 +0900)]
ARM: dts: bcm2710-rpi-3-b : Change audio node status as "okay"

Start.elf uses dt overlay concept, so each node status can be
overlayed with dtparam=audio=on in config.txt but u-boot does not.
So, change status of on-board audio dt node as "okay" because dt
overlay concept on u-boot requires too huge effort.

Fixing dts file from arm will also change arm64 because arm64 dts
includes arm dts.

Change-Id: I73b3c807968c031ba046f44e937c6828ee7f0119
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
[jcsing.lee@samsung.com: modify commit message more clearly]
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
4 years agoarm64: bcmrpi3_defconfig: Enable features related to bcm sound
Lee Hackseung [Thu, 10 Aug 2017 05:50:09 +0000 (14:50 +0900)]
arm64: bcmrpi3_defconfig: Enable features related to bcm sound

Enable SND_BCM2835 that has essential functionalities to
play and capture sounds and enable configurations related to PWM
because earjack works through PWM devices.

Change-Id: I04f7ea23b9bdd447a7f8084d8ce5c6f73ebd9992
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
[jcsing.lee@samsung.com: modify commit message more clearly]
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable android logger
Karol Lewandowski [Wed, 12 Jul 2017 09:54:23 +0000 (11:54 +0200)]
ARM64: tizen_bcmrpi3_defconfig: enable android logger

To support logger driver backend from Tizen dlog framework, enable
android logger.

Change-Id: I24960463efc40637858c0873ac7400fa0e806650
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
4 years agostaging: logger: fix build error due to removed ki_nbytes
Inki Dae [Mon, 4 Jul 2016 08:28:46 +0000 (17:28 +0900)]
staging: logger: fix build error due to removed ki_nbytes

This patch fixes build error. Logger driver was removed
from mainline kernel and after that there was some changes and
one of them is that ki_nbytes member was removed from kiocb structure.
66ee59a fs: remove ki_nbytes

This patch makes count member of iov_iter structure to be used instead.

Change-Id: I11e9ebdac7dd86c02fd692a67562a23e5c685f69
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
4 years agostaging: android: logger: fix the compiler error
Jaehoon Chung [Fri, 5 Jan 2018 00:40:02 +0000 (09:40 +0900)]
staging: android: logger: fix the compiler error

Moved signal wakeup & sigpending methods from <linux/sched.h> into
<linux/sched/signal.h>.

Refer to commit 174cd4b1e5fb (sched/headers: Prepare to move signal
wakeup & sigpending methods from <linux/sched.h> into <linux/sched/signal.h>

Fix the compiler error about android logger.

Change-Id: Iab1583fe54fef1c76a34673d1d718f73930baa11
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agoRevert "staging: Remove logger and alarm-dev from android Makefile"
Karol Lewandowski [Mon, 3 Jul 2017 12:01:57 +0000 (14:01 +0200)]
Revert "staging: Remove logger and alarm-dev from android Makefile"

This reverts commit 71e365ed0ca893cae8d72cbd4b476a9589003098.

Change-Id: I190dabd2626ca7cb51d00d9fe186d15da21ae405
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
4 years agoRevert "staging: Remove the Android logger driver"
Karol Lewandowski [Mon, 3 Jul 2017 12:00:55 +0000 (14:00 +0200)]
Revert "staging: Remove the Android logger driver"

This reverts commit a0a23bbce7818c90c3d3370af966fefce07a8c9b.

rpi3 is going to be used for various profiles - among these
there will be IoT and Headless, which still depend on legacy
android logger driver for application logging.

This commit reverts removal of the driver.

Change-Id: I61ab9e87c5bcbf318aa35ec2f92a470b54a98be1
Requested-by: Hyotaek Shim <hyotaek.shim@samsung.com>
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: update the defconfig for synchronization
Jaehoon Chung [Tue, 22 Aug 2017 03:00:20 +0000 (12:00 +0900)]
ARM64: tizen_bcmrpi3_defconfig: update the defconfig for synchronization

It updates the defconfig for synchronization.

Change-Id: I2f1b2aa7cdcc82c0df0407cde155569884181471
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable BLUETOOTH
Lee Hackseung [Mon, 10 Jul 2017 10:36:22 +0000 (19:36 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable BLUETOOTH

Activate Bluetooth related settings.

Change-Id: I6c9496341698aadc66934ab93a3b54d2f82894ad
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable UVC
Lee Hackseung [Fri, 11 Aug 2017 06:17:38 +0000 (15:17 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable UVC

Activate all settings related to UVC(USB Video Class)

Change-Id: I6d5d3d388d06fc4b5ae9510db63f4398f8fe84fe
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable USB audio driver
Jaechul Lee [Fri, 28 Jul 2017 07:48:32 +0000 (16:48 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable USB audio driver

Activate ALSA USB related settings.

Change-Id: I03d6c9cd9eb6e55667f7bd92717b6beeb304aa1b
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
[jcsing.lee: adjust commit message]
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable GPIO_BCM_EXP
Joonyoung Shim [Wed, 26 Jul 2017 05:27:19 +0000 (14:27 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable GPIO_BCM_EXP

VC4 DRM hdmi uses HPD gpio controlled by Broadcom expander GPIO driver,
so enable GPIO_BCM_EXP config.

Change-Id: I1457a0d2d9d071363eb2f43225a308eeeaaa3353
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable INPUT_EVDEV
Andi Shyti [Tue, 25 Jul 2017 01:55:38 +0000 (10:55 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable INPUT_EVDEV

Tizen needs the dev/input/eventX to interface for with the mouse,
INPUT_EVDEV enables it.

Change-Id: I3a9566a10b8764fe5af21fc6b1361cf9e8040a23
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable SPI_BCM2835
Hyeongsik Min [Tue, 11 Jul 2017 11:24:27 +0000 (20:24 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable SPI_BCM2835

Enables support of BCM2835 SPI driver needed by peripheral-io.

Change-Id: Ibf2aaca64462e4046ba155d11783f19f912ef8c3
Signed-off-by: Hyeongsik Min <hyeongsik.min@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: increase the ramdisk size to 12MB
Jaehoon Chung [Mon, 27 Mar 2017 07:54:15 +0000 (16:54 +0900)]
ARM64: tizen_bcmrpi3_defconfig: increase the ramdisk size to 12MB

Increase the ramdisk size from 4MB to 12MB. Tizen normal ramdisk
size should be under 8MB and the size of ramdisk-recovery should
be 12MB.

Change-Id: I474a32f8fb1233d36b837806dde54e376a0cafdd
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
[sw0312.kim: squash change size for 8MB and 12MB]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defcofig: enable audit subsystem
Karol Lewandowski [Thu, 1 Jun 2017 12:17:37 +0000 (14:17 +0200)]
ARM64: tizen_bcmrpi3_defcofig: enable audit subsystem

Syscall auditing is going to be used by fault detection service - faultd.

Change-Id: Ifc6853e12fcc90497bd8a222eecb44fdd09f57ba
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defcofig: enable the configs relevant to bridge
Jaehoon Chung [Mon, 22 May 2017 23:53:49 +0000 (08:53 +0900)]
ARM64: tizen_bcmrpi3_defcofig: enable the configs relevant to bridge

Enable the configs relevant to BRIDGE and STP.

Change-Id: Iabb67ec49d176ff5fe6083dfc4a48ed40d683d1a
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable the MAC80211 and RT2X00 configs
Jaehoon Chung [Fri, 19 May 2017 03:37:59 +0000 (12:37 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable the MAC80211 and RT2X00 configs

To use Ralink driver, enable the configurations relevant to it.

Change-Id: I5122405b297caf1f6f1e56d02a524d504671d910
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Enable USB_SERIAL configurations
Jaehoon Chung [Wed, 17 May 2017 05:41:08 +0000 (14:41 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Enable USB_SERIAL configurations

Enable USB_SERIAL configurations.
(CONFIG_SERIAL, CONFIG_SERIAL_GENERIC, CONFIG_SERIAL_CP210X)

Change-Id: Icead3fc34b2e37889a1dd407c24aff1444a5ab20
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agodrm/vc4: add gem_info node via debugfs
Joonyoung Shim [Thu, 23 Mar 2017 06:11:01 +0000 (15:11 +0900)]
drm/vc4: add gem_info node via debugfs

The memps requires gem_info with gem_names to analyze graphics
shared memory, so this patch adds gem_info node via debugfs
interface.

Let's save pid/tgid in private file data only once when gem object is
created or prime_fd is imported and use them on gem_info. This is to
solve the wrong pid problem of gem_info created as different processes
share fd of drm device node.

Change-Id: Iaac2ccd63e124dd11a894f0e88ddbb533750f3d4
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[sw0312.kim: fix wrong printing format in gem_info debugfs for 32bit arm build with %zx]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: enable I2C_CHARDEV
Andi Shyti [Fri, 31 Mar 2017 06:23:47 +0000 (15:23 +0900)]
ARM64: tizen_bcmrpi3_defconfig: enable I2C_CHARDEV

The I2C_CHARDEV flag enables the compilation of the i2c-dev
driver which generates a character device of the type /dev/i2c-X
where userspace programs can access to the i2c devices without
the support of any device drivers.

Change-Id: I661d8590bc219c6500bb5fca89df0436aa0efdca
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
4 years agoARM64: dts: bcm2710-rpi-3-b: enable i2c1
Andi Shyti [Fri, 31 Mar 2017 06:20:27 +0000 (15:20 +0900)]
ARM64: dts: bcm2710-rpi-3-b: enable i2c1

i2c bus number 1 is mapped in the Raspberry Pi gpio array for
connecting through i2c external devices.

Change-Id: Ia8f72952f4aed1d737ab75c239ead25bb97d2e3c
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
4 years agoARM64: rpi3: config: enable configurations relevant to WiFi
Jaehoon Chung [Tue, 7 Feb 2017 07:50:54 +0000 (16:50 +0900)]
ARM64: rpi3: config: enable configurations relevant to WiFi

Enable configurations relevant to WiFi.
These configurations are basic configs for using Network.
If needs to enable more configuration, it should be enabled in future.

To use WiFi, enable the brcmfmac driver as modules.
(Needs to install modules in target.)

Change-Id: Ia9961018f6736e3bc709c0d760f0d2d02994c7c8
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Disable FB_BCM2708
Joonyoung Shim [Tue, 7 Feb 2017 05:01:04 +0000 (14:01 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Disable FB_BCM2708

Disable FB driver because of using DRM driver.

Change-Id: I3bfb899c1e0c71a235952934ecaf749a1d90dd85
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: increase CMA size to 256MiB
Joonyoung Shim [Mon, 6 Feb 2017 06:55:03 +0000 (15:55 +0900)]
ARM64: tizen_bcmrpi3_defconfig: increase CMA size to 256MiB

CMA size 5MiB or 64MiB are insufficient in tizen platform.

Change-Id: I83fa78d12af93361a87f0819b7b7abcd5b23fb2e
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Enable I2C_BCM2835
Joonyoung Shim [Tue, 7 Feb 2017 04:58:35 +0000 (13:58 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Enable I2C_BCM2835

It needs to enable I2C_BCM2835 to bind HDMI from drm driver.

Change-Id: Ifcfbcb7bd3ac5a76c2cbbb1acdec45a48bee0201
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Enable DRM_VC4
Joonyoung Shim [Tue, 7 Feb 2017 04:57:30 +0000 (13:57 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Enable DRM_VC4

Enable DRM_VC4 driver for tizen platform.

v2: DRM_VC4 need also to enable SND and SND_SOC configs.

Change-Id: I85568d78710d81ffa4cb1ec6373647e31962d1fe
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agoarm: dts: Add support for drm vc4 on RPI3
Hoegeun Kwon [Thu, 19 Jan 2017 04:49:54 +0000 (13:49 +0900)]
arm: dts: Add support for drm vc4 on RPI3

Fixed the DT status to operate drm vc4.

Change-Id: I06aa84303e1a7c10647ace3799ec09d08ca045eb
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
4 years agoscripts: mkbootimg_rpi3.sh: Add u-boot and optee binaries to boot.img
Seung-Woo Kim [Tue, 12 Sep 2017 05:55:31 +0000 (14:55 +0900)]
scripts: mkbootimg_rpi3.sh: Add u-boot and optee binaries to boot.img

In boot.img for tizen rpi3 image, u-boot and optee atf binaries
are required, so the files should be also installed in boot.img.
Add u-boot.img with optee os for atf and u-boot received from
download.tizen.org to boot.img.

Change-Id: I9778ea5c72697c3e7d0a534627fc65841bb792a1
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoscripts: mkbootimg_rpi3.sh: Add ARM64 kernel/dtb binary to boot.img
Joonyoung Shim [Thu, 9 Feb 2017 06:40:12 +0000 (15:40 +0900)]
scripts: mkbootimg_rpi3.sh: Add ARM64 kernel/dtb binary to boot.img

Add script to create boot.img having boot related files with fat
file system.

Change-Id: I7a03c11ef155dd3ad5fc935511ae764ef699c145
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[sw0312.kim: remove not required kernel.img and add sync command before umount]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoscripts: Add mkbootimg_rpi3.sh
Joonyoung Shim [Tue, 31 Jan 2017 07:16:38 +0000 (16:16 +0900)]
scripts: Add mkbootimg_rpi3.sh

This script is to make boot.img that is fused at boot partition.

Change-Id: I383fc8dee8460176c825e4ea360d37d62072e6d6
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agotools: Add build script for ARM64 kernel of rpi3
Joonyoung Shim [Wed, 25 Jan 2017 04:50:37 +0000 (13:50 +0900)]
tools: Add build script for ARM64 kernel of rpi3

This patch adds build script to build the ARM64 kernel for rpi3 board.

v2: Remove codes for creating fit style image from its

Change-Id: Ie7fa6dbf0b6838832b6a05326fa0ca27e3a7a812
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agopackaging: Added '.gbs.conf' for partial build
Jaechul Lee [Mon, 30 Jan 2017 23:58:22 +0000 (08:58 +0900)]
packaging: Added '.gbs.conf' for partial build

Added gbs configuration file for enhanced building.
it makes gbs build faster than before.

https://source.tizen.org/documentation/reference/git-build-system/maintenance-models-supported-gbs

Change-Id: I79d57aa5eb49d0fbfa9a3744ec2acb032a274e5e
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agopackaging: Disable UBSan build
Denis Khalikov [Fri, 25 Aug 2017 13:11:14 +0000 (16:11 +0300)]
packaging: Disable UBSan build

UBSan build on kernel will cause build error because kernel has its own
sanitizer build options. So, dislable UBSan build from packaging spec.

Change-Id: Ife910a1e666c6fcafb7ef7bfcc072d88d8549d77
Signed-off-by: Denis Khalikov <d.khalikov@partner.samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agopackaging: Turn off building with ASan
Gonzha Dmitriy Evgenevich [Wed, 24 May 2017 10:51:05 +0000 (13:51 +0300)]
packaging: Turn off building with ASan

Turn off ASan for ASan sanitized firmware build

Change-Id: If786306821ff22e994efaba2b00dcabcc5eb8426
Signed-off-by: Gonzha Dmitriy Evgenevich <d.gonzha@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agopackaging: Add kernel devel package
Alexander Aksenov [Thu, 27 Jul 2017 12:53:34 +0000 (15:53 +0300)]
packaging: Add kernel devel package

Kernel devel is used now to build out-of-tree kernel modules

Change-Id: I753edba92042561b50dc6c645f23659a65568976
Signed-off-by: Alexander Aksenov <a.aksenov@samsung.com>
4 years agopackaging: Add spec file for rpi
Joonyoung Shim [Tue, 24 Jan 2017 04:19:59 +0000 (13:19 +0900)]
packaging: Add spec file for rpi

This adds linux-rpi3.spec file for ARM64/armv7l rpm packaging.

Change-Id: I428fd32b69d082d935159476ace30c59c14b570d
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[jh80.chung, sw0312.kim: Update kernel version to v4.14.y in spec file]
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
[sw0312.kim: Rename spec file without arch name]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Enable SMACK
Joonyoung Shim [Tue, 7 Feb 2017 04:26:20 +0000 (13:26 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Enable SMACK

It needs to enable configs related with SMACK for booting tizen
platform.

Change-Id: If58917b798c1bee0c16cd5e430a065e40852b97b
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agoARM64: tizen_bcmrpi3_defconfig: Sync with .config
Joonyoung Shim [Tue, 7 Feb 2017 04:25:14 +0000 (13:25 +0900)]
ARM64: tizen_bcmrpi3_defconfig: Sync with .config

Change-Id: I4e11df92a40b5f4c48891a6e772d898ff58de6e8
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agorpi3: config: Enable camera
Hackseung Lee [Wed, 6 Dec 2017 08:33:44 +0000 (17:33 +0900)]
rpi3: config: Enable camera

Add configration to enable the Raspberry Pi Camera Module in config.txt file.

Change-Id: I092851a559ebab462babf8c176a190339285ef9d
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
4 years agorpi3: enable jtag gpio option
Seung-Woo Kim [Thu, 26 Oct 2017 03:55:05 +0000 (12:55 +0900)]
rpi3: enable jtag gpio option

Enable jtag gpio option at 1st bootloader level. The option
enables jtag gpio as alt4 mode as like following:
 GPIO22 - PIN13 - TRST
 GPIO23 - PIN16 - RTCK
 GPIO24 - PIN18 - TDO
 GPIO25 - PIN22 - TCK
 GPIO26 - PIN37 - TDI
 GPIO27 - PIN07 - TMS

This is requested for debugging secure world with jtag.

Change-Id: I0e25dd9ecf95fa003e56eb73eae5a668a1f6e3ba
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agorpi3: Enable ARM atf boot for rpi3
r.tyminski [Fri, 6 Oct 2017 15:39:37 +0000 (17:39 +0200)]
rpi3: Enable ARM atf boot for rpi3

Boot rpi3 with u-boot-spl.bin which enables ARM atf.
Other booting options are set as like:
https://github.com/OP-TEE/build/blob/master/rpi3/firmware/config.txt

Change-Id: I0c0559c3f72f252c2cd2716b746b3c49b04fd63e
Signed-off-by: Rafal Tyminski <r.tyminski@partner.samsung.com>
[sw0312.kim: add more options and adjust commit-msg]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agorpi3: enable uart in bootcode.bin
Łukasz Stelmach [Fri, 29 Sep 2017 13:51:08 +0000 (15:51 +0200)]
rpi3: enable uart in bootcode.bin

The uart_2ndstage option directs bootcode.bin to print some diagnostics,
that indicate the code is running.

Change-Id: I34a68ae3b5c2467ee58fd81adf687ce367e1ed1c
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
4 years agorpi3: config: change the 'kernel' parameter from Image to u-boot.bin
Jaehoon Chung [Wed, 12 Jul 2017 04:22:47 +0000 (13:22 +0900)]
rpi3: config: change the 'kernel' parameter from Image to u-boot.bin

It needs to use the u-boot for supporting ramdisk booting.
Current release image is including the u-boot.bin that modified the ramdisk
booting sequence.

Change the kernel parameter from "Image" to "u-boot.bin" in config.txt.

Change-Id: Icc4ddce7e9f9befba59240d02ddd9af111c92a40
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agorpi3: config: Enable SPI interface
Hyeongsik Min [Tue, 11 Jul 2017 11:55:13 +0000 (20:55 +0900)]
rpi3: config: Enable SPI interface

Uncomment spi=on in config.txt file to enable SPI interface.

Change-Id: I595628838fe9d769b243948e7118d36f4647e490
Signed-off-by: Hyeongsik Min <hyeongsik.min@samsung.com>
4 years agorpi3: config: Add loading of arm64 kernel binary & dtb
Joonyoung Shim [Tue, 31 Jan 2017 01:57:34 +0000 (10:57 +0900)]
rpi3: config: Add loading of arm64 kernel binary & dtb

Change-Id: Ib553d02595e357751d0080d6aa713efe1ce9515d
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agorpi3: config: Add boot mode to select ARM or ARM64
Joonyoung Shim [Wed, 25 Jan 2017 07:57:30 +0000 (16:57 +0900)]
rpi3: config: Add boot mode to select ARM or ARM64

Add configration to select boot mode in config.txt file, then we can
determine booting in 32-bit mode or 64-bit mode.

Change-Id: I2a5a1b11c4c83f514a7e8cc4c2f077b0b1d02cdc
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agorpi3: config: Enable serial
Joonyoung Shim [Wed, 25 Jan 2017 06:58:47 +0000 (15:58 +0900)]
rpi3: config: Enable serial

Add configration to enable serial in config.txt file, then we can serial
log from kernel or u-boot during booting.

Change-Id: Iebe3345b52cb2886daa0d8bdf1e15747dde2af39
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agorpi3: Add config.txt extracted from raspbian lite binary
Joonyoung Shim [Wed, 25 Jan 2017 09:41:38 +0000 (18:41 +0900)]
rpi3: Add config.txt extracted from raspbian lite binary

We can get raspbian lite binary from
https://downloads.raspberrypi.org/raspbian_lite_latest

This file that is necessary for booting was extracted from first
partition of 2017-07-05-raspbian-jessie-lite.img.

Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
4 years agorpi3: Add boot files from github
Joonyoung Shim [Wed, 26 Jul 2017 00:07:51 +0000 (09:07 +0900)]
rpi3: Add boot files from github

We can get boot binaries that are necessary for booting from master
branch of https://github.com/raspberrypi/firmware.

The git base is the commit 83977fe3b6ef ("kernel: Bump to 4.14.98").

LICENCE.broadcom
bootcode.bin
fixup*.dat
start*.elf

TYPES of each firmware:
start.elf       / fixup.dat     - normal
start_x.elf     / fixup_x.dat   - with extra feature including camera (start_x=1 in config.txt)
start_cd.elf    / fixup_cd.dat  - cut-down to minimum gpu set 16M
start_db.elf    / fixup_db.dat  - debug (start_debug=1 in config.txt)

NOTE:
start_x=1 in config.txt should be specified when using the camera
module and it implies start_file=start_x.elf/fixup_file=fixup_x.dat.

Change-Id: I827b4cb94b3f8baa805938cd9f44947be7865f0e
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
[lhs: Add firmware files for camera]
Signed-off-by: Hackseung Lee <lhs@dignsys.com>
[sw0312.kim: update firmware files including extra, cutdown and debug features]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
4 years agoMerge remote-tracking branch 'stable/linux-4.19.y' into rpi-4.19.y
popcornmix [Fri, 1 Nov 2019 13:52:14 +0000 (13:52 +0000)]
Merge remote-tracking branch 'stable/linux-4.19.y' into rpi-4.19.y

4 years agorpi-poe-fan: fix def_pwm1 writes
Serge Schneider [Thu, 31 Oct 2019 13:37:16 +0000 (13:37 +0000)]
rpi-poe-fan: fix def_pwm1 writes

Signed-off-by: Serge Schneider <serge@raspberrypi.org>
4 years agoLinux 4.19.81 v4.19.81
Greg Kroah-Hartman [Tue, 29 Oct 2019 08:20:09 +0000 (09:20 +0100)]
Linux 4.19.81

4 years agoRDMA/cxgb4: Do not dma memory off of the stack
Greg KH [Tue, 1 Oct 2019 16:56:11 +0000 (18:56 +0200)]
RDMA/cxgb4: Do not dma memory off of the stack

commit 3840c5b78803b2b6cc1ff820100a74a092c40cbb upstream.

Nicolas pointed out that the cxgb4 driver is doing dma off of the stack,
which is generally considered a very bad thing.  On some architectures it
could be a security problem, but odds are none of them actually run this
driver, so it's just a "normal" bug.

Resolve this by allocating the memory for a message off of the heap
instead of the stack.  kmalloc() always will give us a proper memory
location that DMA will work correctly from.

Link: https://lore.kernel.org/r/20191001165611.GA3542072@kroah.com
Reported-by: Nicolas Waisman <nico@semmle.com>
Tested-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agoblk-rq-qos: fix first node deletion of rq_qos_del()
Tejun Heo [Tue, 15 Oct 2019 15:49:27 +0000 (08:49 -0700)]
blk-rq-qos: fix first node deletion of rq_qos_del()

commit 307f4065b9d7c1e887e8bdfb2487e4638559fea1 upstream.

rq_qos_del() incorrectly assigns the node being deleted to the head if
it was the first on the list in the !prev path.  Fix it by iterating
with ** instead.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Fixes: a79050434b45 ("blk-rq-qos: refactor out common elements of blk-wbt")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agoPCI: PM: Fix pci_power_up()
Rafael J. Wysocki [Mon, 14 Oct 2019 11:25:00 +0000 (13:25 +0200)]
PCI: PM: Fix pci_power_up()

commit 45144d42f299455911cc29366656c7324a3a7c97 upstream.

There is an arbitrary difference between the system resume and
runtime resume code paths for PCI devices regarding the delay to
apply when switching the devices from D3cold to D0.

Namely, pci_restore_standard_config() used in the runtime resume
code path calls pci_set_power_state() which in turn invokes
__pci_start_power_transition() to power up the device through the
platform firmware and that function applies the transition delay
(as per PCI Express Base Specification Revision 2.0, Section 6.6.1).
However, pci_pm_default_resume_early() used in the system resume
code path calls pci_power_up() which doesn't apply the delay at
all and that causes issues to occur during resume from
suspend-to-idle on some systems where the delay is required.

Since there is no reason for that difference to exist, modify
pci_power_up() to follow pci_set_power_state() more closely and
invoke __pci_start_power_transition() from there to call the
platform firmware to power up the device (in case that's necessary).

Fixes: db288c9c5f9d ("PCI / PM: restore the original behavior of pci_set_power_state()")
Reported-by: Daniel Drake <drake@endlessm.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/linux-pm/CAD8Lp44TYxrMgPLkHCqF9hv6smEurMXvmmvmtyFhZ6Q4SE+dig@mail.gmail.com/T/#m21be74af263c6a34f36e0fc5c77c5449d9406925
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agoxen/netback: fix error path of xenvif_connect_data()
Juergen Gross [Fri, 18 Oct 2019 07:45:49 +0000 (09:45 +0200)]
xen/netback: fix error path of xenvif_connect_data()

commit 3d5c1a037d37392a6859afbde49be5ba6a70a6b3 upstream.

xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().

Remove the superfluous module_put().

Fixes: 279f438e36c0a7 ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agocpufreq: Avoid cpufreq_suspend() deadlock on system shutdown
Rafael J. Wysocki [Tue, 8 Oct 2019 23:29:10 +0000 (01:29 +0200)]
cpufreq: Avoid cpufreq_suspend() deadlock on system shutdown

commit 65650b35133ff20f0c9ef0abd5c3c66dbce3ae57 upstream.

It is incorrect to set the cpufreq syscore shutdown callback pointer
to cpufreq_suspend(), because that function cannot be run in the
syscore stage of system shutdown for two reasons: (a) it may attempt
to carry out actions depending on devices that have already been shut
down at that point and (b) the RCU synchronization carried out by it
may not be able to make progress then.

The latter issue has been present since commit 45975c7d21a1 ("rcu:
Define RCU-sched API in terms of RCU for Tree RCU PREEMPT builds"),
but the former one has been there since commit 90de2a4aa9f3 ("cpufreq:
suspend cpufreq governors on shutdown") regardless.

Fix that by dropping cpufreq_syscore_ops altogether and making
device_shutdown() call cpufreq_suspend() directly before shutting
down devices, which is along the lines of what system-wide power
management does.

Fixes: 45975c7d21a1 ("rcu: Define RCU-sched API in terms of RCU for Tree RCU PREEMPT builds")
Fixes: 90de2a4aa9f3 ("cpufreq: suspend cpufreq governors on shutdown")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agomemstick: jmb38x_ms: Fix an error handling path in 'jmb38x_ms_probe()'
Christophe JAILLET [Sat, 5 Oct 2019 11:21:01 +0000 (13:21 +0200)]
memstick: jmb38x_ms: Fix an error handling path in 'jmb38x_ms_probe()'

commit 28c9fac09ab0147158db0baeec630407a5e9b892 upstream.

If 'jmb38x_ms_count_slots()' returns 0, we must undo the previous
'pci_request_regions()' call.

Goto 'err_out_int' to fix it.

Fixes: 60fdd931d577 ("memstick: add support for JMicron jmb38x MemoryStick host controller")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agobtrfs: tracepoints: Fix bad entry members of qgroup events
Qu Wenruo [Thu, 17 Oct 2019 02:38:37 +0000 (10:38 +0800)]
btrfs: tracepoints: Fix bad entry members of qgroup events

commit 1b2442b4ae0f234daeadd90e153b466332c466d8 upstream.

[BUG]
For btrfs:qgroup_meta_reserve event, the trace event can output garbage:

  qgroup_meta_reserve: 9c7f6acc-b342-4037-bc47-7f6e4d2232d7: refroot=5(FS_TREE) type=DATA diff=2
  qgroup_meta_reserve: 9c7f6acc-b342-4037-bc47-7f6e4d2232d7: refroot=5(FS_TREE) type=0x258792 diff=2

The @type can be completely garbage, as DATA type is not possible for
trace_qgroup_meta_reserve() trace event.

[CAUSE]
Ther are several problems related to qgroup trace events:
- Unassigned entry member
  Member entry::type of trace_qgroup_update_reserve() and
  trace_qgourp_meta_reserve() is not assigned

- Redundant entry member
  Member entry::type is completely useless in
  trace_qgroup_meta_convert()

Fixes: 4ee0d8832c2e ("btrfs: qgroup: Update trace events for metadata reservation")
CC: stable@vger.kernel.org # 4.10+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agoBtrfs: check for the full sync flag while holding the inode lock during fsync
Filipe Manana [Wed, 16 Oct 2019 15:28:52 +0000 (16:28 +0100)]
Btrfs: check for the full sync flag while holding the inode lock during fsync

commit ba0b084ac309283db6e329785c1dc4f45fdbd379 upstream.

We were checking for the full fsync flag in the inode before locking the
inode, which is racy, since at that that time it might not be set but
after we acquire the inode lock some other task set it. One case where
this can happen is on a system low on memory and some concurrent task
failed to allocate an extent map and therefore set the full sync flag on
the inode, to force the next fsync to work in full mode.

A consequence of missing the full fsync flag set is hitting the problems
fixed by commit 0c713cbab620 ("Btrfs: fix race between ranged fsync and
writeback of adjacent ranges"), BUG_ON() when dropping extents from a log
tree, hitting assertion failures at tree-log.c:copy_items() or all sorts
of weird inconsistencies after replaying a log due to file extents items
representing ranges that overlap.

So just move the check such that it's done after locking the inode and
before starting writeback again.

Fixes: 0c713cbab620 ("Btrfs: fix race between ranged fsync and writeback of adjacent ranges")
CC: stable@vger.kernel.org # 5.2+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agoBtrfs: add missing extents release on file extent cluster relocation error
Filipe Manana [Wed, 9 Oct 2019 16:43:45 +0000 (17:43 +0100)]
Btrfs: add missing extents release on file extent cluster relocation error

commit 44db1216efe37bf670f8d1019cdc41658d84baf5 upstream.

If we error out when finding a page at relocate_file_extent_cluster(), we
need to release the outstanding extents counter on the relocation inode,
set by the previous call to btrfs_delalloc_reserve_metadata(), otherwise
the inode's block reserve size can never decrease to zero and metadata
space is leaked. Therefore add a call to btrfs_delalloc_release_extents()
in case we can't find the target page.

Fixes: 8b62f87bad9c ("Btrfs: rework outstanding_extents")
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agobtrfs: block-group: Fix a memory leak due to missing btrfs_put_block_group()
Qu Wenruo [Thu, 10 Oct 2019 02:39:26 +0000 (10:39 +0800)]
btrfs: block-group: Fix a memory leak due to missing btrfs_put_block_group()

commit 4b654acdae850f48b8250b9a578a4eaa518c7a6f upstream.

In btrfs_read_block_groups(), if we have an invalid block group which
has mixed type (DATA|METADATA) while the fs doesn't have MIXED_GROUPS
feature, we error out without freeing the block group cache.

This patch will add the missing btrfs_put_block_group() to prevent
memory leak.

Note for stable backports: the file to patch in versions <= 5.3 is
fs/btrfs/extent-tree.c

Fixes: 49303381f19a ("Btrfs: bail out if block group has different mixed flag")
CC: stable@vger.kernel.org # 4.9+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 years agopinctrl: armada-37xx: swap polarity on LED group
Patrick Williams [Tue, 1 Oct 2019 15:51:38 +0000 (10:51 -0500)]
pinctrl: armada-37xx: swap polarity on LED group

commit b835d6953009dc350d61402a854b5a7178d8c615 upstream.

The configuration registers for the LED group have inverted
polarity, which puts the GPIO into open-drain state when used in
GPIO mode.  Switch to '0' for GPIO and '1' for LED modes.

Fixes: 87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191001155154.99710-1-alpawi@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>