review.tizen.org Git - platform/kernel/linux-starfive.git/log

Bluetooth: btusb: Add a new VID/PID 0e8d/0608 for MT7921

Add a new PID/VID 0e8d/0608 for MT7921K chip found on AMD RZ608 module.

From /sys/kernel/debug/usb/devices:
T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0e8d ProdID=0608 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btusb: Add a new PID/VID 13d3/3583 for MT7921

Add VID 13D3 & PID 3583 for MediaTek MT7921 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=03 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3583 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: avoid hci_dev_test_and_set_flag() in mgmt_init_hdev()

syzbot is again reporting attempt to cancel uninitialized work
at mgmt_index_removed() [1], for setting of HCI_MGMT flag from
mgmt_init_hdev() from hci_mgmt_cmd() from hci_sock_sendmsg() can
race with testing of HCI_MGMT flag from mgmt_index_removed() from
hci_sock_bind() due to lack of serialization via hci_dev_lock().

Since mgmt_init_hdev() is called with mgmt_chan_list_lock held, we can
safely split hci_dev_test_and_set_flag() into hci_dev_test_flag() and
hci_dev_set_flag(). Thus, in order to close this race, set HCI_MGMT flag
after INIT_DELAYED_WORK() completed.

This is a local fix based on mgmt_chan_list_lock. Lack of serialization
via hci_dev_lock() might be causing different race conditions somewhere
else. But a global fix based on hci_dev_lock() should deserve a future
patch.

Link: https://syzkaller.appspot.com/bug?extid=844c7bf1b1aa4119c5de
Reported-by: syzbot+844c7bf1b1aa4119c5de@syzkaller.appspotmail.com
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 3f2893d3c142986a ("Bluetooth: don't try to cancel uninitialized works at mgmt_index_removed()")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btintel: Mark Intel controller to support LE_STATES quirk

HarrrisonPeak, CyclonePeak, SnowFieldPeak and SandyPeak controllers
are marked to support HCI_QUIRK_LE_STATES.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btintel: Add support for Magnetor

Hardware variant for Magnetor core (CNVi) is added.

Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btusb: Add a new PID/VID 13d3/3578 for MT7921

Add VID 13D3 & PID 3578 for MediaTek MT7921 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=03 Lev=01 Prnt=01 Port=07 Cnt=03 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3578 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Fix HCIGETDEVINFO regression

Recent changes breaks HCIGETDEVINFO since it changes the size of
hci_dev_info.

Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: Fix hci_read_buffer_size_sync

hci_read_buffer_size_sync shall not use HCI_OP_LE_READ_BUFFER_SIZE_V2
sinze that is LE specific, instead it is hci_le_read_buffer_size_sync
version that shall use it.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216382
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Add experimental wrapper for MGMT based mesh

This introduces a "Mesh UUID" and an Experimental Feature bit to the
hdev mask, and depending all underlying Mesh functionality on it.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Implement support for Mesh

The patch adds state bits, storage and HCI command chains for sending
and receiving Bluetooth Mesh advertising packets, and delivery to
requesting user space processes. It specifically creates 4 new MGMT
commands and 2 new MGMT events:

MGMT_OP_SET_MESH_RECEIVER - Sets passive scan parameters and a list of
AD Types which will trigger Mesh Packet Received events

MGMT_OP_MESH_READ_FEATURES - Returns information on how many outbound
Mesh packets can be simultaneously queued, and what the currently queued
handles are.

MGMT_OP_MESH_SEND - Command to queue a specific outbound Mesh packet,
with the number of times it should be sent, and the BD Addr to use.
Discrete advertisments are added to the ADV Instance list.

MGMT_OP_MESH_SEND_CANCEL - Command to cancel a prior outbound message
request.

MGMT_EV_MESH_DEVICE_FOUND - Event to deliver entire received Mesh
Advertisement packet, along with timing information.

MGMT_EV_MESH_PACKET_CMPLT - Event to indicate that an outbound packet is
no longer queued for delivery.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btusb: mediatek: fix WMT failure during runtime suspend

WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.

Fixes: a1c49c434e15 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btusb: Add BT device 0cb8:c549 from RTW8852AE to tables

A new Bluetooth device for the Realtek RTW8852AE has been noted.

This device has the following lsusb output:

Bus 001 Device 003: ID 0cb8:c549 Opticis Co., Ltd Bluetooth Radio

The pertinent part of /sys/kernel/debug/usb/devices is as follows:

T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cb8 ProdID=c549 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btusb: Add RTL8761BUV device (Edimax BT-8500)

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=7392 ProdID=c611 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=Edimax Bluetooth Adapter
S:  SerialNumber=XXXXXXXXXXXX
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: btusb: Add Realtek RTL8852C support ID 0x13D3:0x3592

Add the support ID(0x13D3, 0x3592) to usb_device_id table for
Realtek RTL8852C.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3592 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Move hci_abort_conn to hci_conn.c

hci_abort_conn() is a wrapper around a number of DISCONNECT and
CREATE_CONN_CANCEL commands that was being invoked from hci_request
request queues, which are now deprecated. There are two versions:
hci_abort_conn() which can be invoked from the hci_event thread, and
hci_abort_conn_sync() which can be invoked within a hci_sync cmd chain.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Normalize HCI_OP_READ_ENC_KEY_SIZE cmdcmplt

The HCI_OP_READ_ENC_KEY_SIZE command is converted from using the
deprecated hci_request mechanism to use hci_send_cmd, with an
accompanying hci_cc_read_enc_key_size to handle it's return response.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: hold hdev->lock when cleanup hci_conn

When disconnecting all devices, hci_conn_failed is used to cleanup
hci_conn object when the hci_conn object cannot be aborted.
The function hci_conn_failed requires the caller holds hdev->lock.

Fixes: 9b3628d79b46f ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_event: Fix checking conn for le_conn_complete_evt

To prevent multiple conn complete events, we shouldn't look up the
conn with hci_lookup_le_connect, since it requires the state to be
BT_CONNECT. By the time the duplicate event is processed, the state
might have changed, so we end up processing the new event anyway.

Change the lookup function to hci_conn_hash_lookup_ba.

Fixes: d5ebaa7c5f6f6 ("Bluetooth: hci_event: Ignore multiple conn complete events")
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: ISO: Fix not handling shutdown condition

In order to properly handle shutdown syscall the code shall not assume
that the how argument is always SHUT_RDWR resulting in SHUTDOWN_MASK as
that would result in poll to immediately report EPOLLHUP instead of
properly waiting for disconnect_cfm (Disconnect Complete) which is
rather important for the likes of BAP as the CIG may need to be
reprogrammed.

Fixes: ccf74f2390d6 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: fix double mgmt_pending_free() in remove_adv_monitor()

syzbot is reporting double kfree() at remove_adv_monitor() [1], for
commit 7cf5c2978f23fdbb ("Bluetooth: hci_sync: Refactor remove Adv
Monitor") forgot to remove duplicated mgmt_pending_remove() when
merging "if (err) {" path and "if (!pending) {" path.

Link: https://syzkaller.appspot.com/bug?extid=915a8416bf15895b8e07
Reported-by: syzbot <syzbot+915a8416bf15895b8e07@syzkaller.appspotmail.com>
Fixes: 7cf5c2978f23fdbb ("Bluetooth: hci_sync: Refactor remove Adv Monitor")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: MGMT: Fix Get Device Flags

Get Device Flags don't check if device does actually use an RPA in which
case it shall only set HCI_CONN_FLAG_REMOTE_WAKEUP if LL Privacy is
enabled.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: L2CAP: Fix build errors in some archs

This attempts to fix the follow errors:

In function 'memcmp',
    inlined from 'bacmp' at ./include/net/bluetooth/bluetooth.h:347:9,
    inlined from 'l2cap_global_chan_by_psm' at
    net/bluetooth/l2cap_core.c:2003:15:
./include/linux/fortify-string.h:44:33: error: '__builtin_memcmp'
specified bound 6 exceeds source size 0 [-Werror=stringop-overread]
   44 | #define __underlying_memcmp     __builtin_memcmp
      |                                 ^
./include/linux/fortify-string.h:420:16: note: in expansion of macro
'__underlying_memcmp'
  420 |         return __underlying_memcmp(p, q, size);
      |                ^~~~~~~~~~~~~~~~~~~
In function 'memcmp',
    inlined from 'bacmp' at ./include/net/bluetooth/bluetooth.h:347:9,
    inlined from 'l2cap_global_chan_by_psm' at
    net/bluetooth/l2cap_core.c:2004:15:
./include/linux/fortify-string.h:44:33: error: '__builtin_memcmp'
specified bound 6 exceeds source size 0 [-Werror=stringop-overread]
   44 | #define __underlying_memcmp     __builtin_memcmp
      |                                 ^
./include/linux/fortify-string.h:420:16: note: in expansion of macro
'__underlying_memcmp'
  420 |         return __underlying_memcmp(p, q, size);
      |                ^~~~~~~~~~~~~~~~~~~

Fixes: 332f1795ca20 ("Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm regression")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_sync: Fix suspend performance regression

This attempts to fix suspend performance when there is no connections by
not updating the event mask.

Fixes: ef61b6ea1544 ("Bluetooth: Always set event mask on suspend")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: hci_event: Fix vendor (unknown) opcode status handling

Commit c8992cffbe74 ("Bluetooth: hci_event: Use of a function table to
handle Command Complete") was (presumably) meant to only refactor things
without any functional changes.

But it does have one undesirable side-effect, before *status would always
be set to skb->data[0] and it might be overridden by some of the opcode
specific handling. While now it always set by the opcode specific handlers.
This means that if the opcode is not known *status does not get set any
more at all!

This behavior change has broken bluetooth support for BCM4343A0 HCIs,
the hci_bcm.c code tries to configure UART attached HCIs at a higher
baudraute using vendor specific opcodes. The BCM4343A0 does not
support this and this used to simply fail:

[   25.646442] Bluetooth: hci0: BCM: failed to write clock (-56)
[   25.646481] Bluetooth: hci0: Failed to set baudrate

After which things would continue with the initial baudraute. But now
that hci_cmd_complete_evt() no longer sets status for unknown opcodes
*status is left at 0. This causes the hci_bcm.c code to think the baudraute
has been changed on the HCI side and to also adjust the UART baudrate,
after which communication with the HCI is broken, leading to:

[   28.579042] Bluetooth: hci0: command 0x0c03 tx timeout
[   36.961601] Bluetooth: hci0: BCM: Reset failed (-110)

And non working bluetooth. Fix this by restoring the previous
default "*status = skb->data[0]" handling for unknown opcodes.

Fixes: c8992cffbe74 ("Bluetooth: hci_event: Use of a function table to handle Command Complete")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: convert hci_update_adv_data to hci_sync

hci_update_adv_data() is called from hci_event and hci_core due to
events from the controller. The prior function used the deprecated
hci_request method, and the new one uses hci_sync.c

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: move hci_get_random_address() to hci_sync

This function has no dependencies on the deprecated hci_request
mechanism, so has been moved unchanged to hci_sync.c

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Delete unreferenced hci_request code

This patch deletes a whole bunch of code no longer reached because the
functionality was recoded using hci_sync.c

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Move Adv Instance timer to hci_sync

The Advertising Instance expiration timer adv_instance_expire was
handled with the deprecated hci_request mechanism, rather than it's
replacement: hci_sync.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Convert SCO configure_datapath to hci_sync

Recoding HCI cmds to offload SCO codec to use hci_sync mechanism rather
than deprecated hci_request mechanism.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Delete unused hci_req_stop_discovery()

hci_req_stop_discovery has been deprecated in favor of
hci_stop_discovery_sync() as part of transition to hci_sync.c

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Rework le_scan_restart for hci_sync

le_scan_restart delayed work queue was running as a deprecated
hci_request instead of on the newer thread-safe hci_sync mechanism.

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Convert le_scan_disable timeout to hci_sync

The le_scan_disable timeout was being performed on the deprecated
hci_request.c mechanism. This timeout is performed in hci_sync.c

Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Bluetooth: Add VID/PID 0489/e0e0 for MediaTek MT7921

Tested on HP Envy ey0xxx

output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0e0 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us

Signed-off-by: Fae <faenkhauser@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

netdev: Use try_cmpxchg in napi_if_scheduled_mark_missed

Use try_cmpxchg instead of cmpxchg (*ptr, old, new) == old in
napi_if_scheduled_mark_missed. x86 CMPXCHG instruction returns
success in ZF flag, so this change saves a compare after cmpxchg
(and related move instruction in front of cmpxchg).

Also, try_cmpxchg implicitly assigns old *ptr value to "old" when cmpxchg
fails, enabling further code simplifications.

Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20220822143243.2798-1-ubizjak@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'mlxsw-remove-some-unused-code'

Petr Machata says:

====================
mlxsw: Remove some unused code

This patchset removes code that is not used anymore after the following two
commits removed all users:

- commit b0d80c013b04 ("mlxsw: Remove Mellanox SwitchX-2 ASIC support")
- commit 9b43fbb8ce24 ("mlxsw: Remove Mellanox SwitchIB ASIC support")
====================

Link: https://lore.kernel.org/r/cover.1661350629.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: Remove unused mlxsw_core_port_type_get()

Function mlxsw_core_port_type_get() is no longer used. So remove it.

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: Remove unused port_type_set devlink op

port_type_set devlink op is no longer used by any mlxsw driver,
so remove it.

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: Remove unused IB stuff

There are some IB leftovers that are no longer used in the code.
So remove them.

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'net-devlink-sync-flash-and-dev-info-commands'

Jiri Pirko says:

====================
net: devlink: sync flash and dev info commands

Purpose of this patchset is to introduce consistency between two devlink
commands:
  devlink dev info
    Shows versions of running default flash target and components.
  devlink dev flash
    Flashes default flash target or component name (if specified
    on cmdline).

Currently it is up to the driver what versions to expose and what flash
update component names to accept. This is inconsistent. Thankfully, only
netdevsim currently using components so it is still time
to sanitize this.

This patchset makes sure, that devlink.c calls into driver for
component flash update only in case the driver exposes the same version
name.

Example:
$ devlink dev info
netdevsim/netdevsim10:
  driver netdevsim
  versions:
      running:
        fw.mgmt 10.20.30
      stored:
        fw.mgmt 10.20.30
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin
[fw.mgmt] Preparing to flash
[fw.mgmt] Flashing 100%
[fw.mgmt] Flash select
[fw.mgmt] Flashing done
$ devlink dev flash netdevsim/netdevsim10 file somefile.bin component fw.mgmt
[fw.mgmt] Preparing to flash
[fw.mgmt] Flashing 100%
[fw.mgmt] Flash select
[fw.mgmt] Flashing done

$ devlink dev flash netdevsim/netdevsim10 file somefile.bin component dummy
Error: selected component is not supported by this device.
====================

Link: https://lore.kernel.org/r/20220824122011.1204330-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: devlink: limit flash component name to match version returned by info_get()

Limit the acceptance of component name passed to cmd_flash_update() to
match one of the versions returned by info_get(), marked by version type.
This makes things clearer and enforces 1:1 mapping between exposed
version and accepted flash component.

Check VERSION_TYPE_COMPONENT version type during cmd_flash_update()
execution by calling info_get() with different "req" context.
That causes info_get() to lookup the component name instead of
filling-up the netlink message.

Remove "UPDATE_COMPONENT" flag which becomes used.

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

netdevsim: add version fw.mgmt info info_get() and mark as a component

Fix the only component user which is netdevsim. It uses component named
"fw.mgmt" in selftests. So add this version to info_get() output with
version type component.

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: devlink: extend info_get() version put to indicate a flash component

Whenever the driver is called by his info_get() op, it may put multiple
version names and values to the netlink message. Extend by additional
helper devlink_info_version_running/stored_put_ext() that allows to
specify a version type that indicates when particular version name
represents a flash component.

This is going to be used in follow-up patch calling info_get() during
flash update command checking if version with this the version type
exists.

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests/net: fix reinitialization of TEST_PROGS in net self tests.

Assinging will drop all previous tests.

Fixes: b690842d12fd ("selftests/net: test l2 tunnel TOS/TTL inheriting")
Signed-off-by: Adel Abouchaev <adel.abushaev@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220824184351.3759862-1-adel.abushaev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: sched: delete duplicate cleanup of backlog and qlen

qdisc_reset() is clearing qdisc->q.qlen and qdisc->qstats.backlog
_after_ calling qdisc->ops->reset. There is no need to clear them
again in the specific reset function.

Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220824005231.345727-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

nfp: flower: support case of match on ct_state(0/0x3f)

is_post_ct_flow() function will process only ct_state ESTABLISHED,
then offload_pre_check() function will check FLOW_DISSECTOR_KEY_CT flag.
When config tc filter match ct_state(0/0x3f), dissector->used_keys
with FLOW_DISSECTOR_KEY_CT bit, function offload_pre_check() will
return false, so not offload. This is a special case that can be handled
safely.

Therefore, modify to let initial packet which won't go through conntrack
can be offloaded, as long as the cared ct fields are all zero.

Signed-off-by: Wenjuan Geng <wenjuan.geng@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220823090122.403631-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: gro: skb_gro_header helper function

Introduce a simple helper function to replace a common pattern.
When accessing the GRO header, we fetch the pointer from frag0,
then test its validity and fetch it from the skb when necessary.

This leads to the pattern
skb_gro_header_fast -> skb_gro_header_hard -> skb_gro_header_slow
recurring many times throughout GRO code.

This patch replaces these patterns with a single inlined function
call, improving code readability.

Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220823071034.GA56142@debian
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Documentation: devlink: fix the locking section

As all callbacks are converted now, fix the text reflecting that change.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220823070213.1008956-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'add-a-second-bind-table-hashed-by-port-and-address'

Joanne Koong says:

====================
Add a second bind table hashed by port and address

Currently, there is one bind hashtable (bhash) that hashes by port only.
This patchset adds a second bind table (bhash2) that hashes by port and
address.

The motivation for adding bhash2 is to expedite bind requests in situations
where the port has many sockets in its bhash table entry (eg a large number
of sockets bound to different addresses on the same port), which makes checking
bind conflicts costly especially given that we acquire the table entry spinlock
while doing so, which can cause softirq cpu lockups and can prevent new tcp
connections.

We ran into this problem at Meta where the traffic team binds a large number
of IPs to port 443 and the bind() call took a significant amount of time
which led to cpu softirq lockups, which caused packet drops and other failures
on the machine.

When experimentally testing this on a local server for ~24k sockets bound to
the port, the results seen were:

ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds

ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds

The additions to the initial bhash2 submission [0] are:
* Updating bhash2 in the cases where a socket's rcv saddr changes after it has
* been bound
* Adding locks for bhash2 hashbuckets

[0] https://lore.kernel.org/netdev/20220520001834.2247810-1-kuba@kernel.org/

v3: https://lore.kernel.org/netdev/20220722195406.1304948-2-joannelkoong@gmail.com/
v2: https://lore.kernel.org/netdev/20220712235310.1935121-1-joannelkoong@gmail.com/
v1: https://lore.kernel.org/netdev/20220623234242.2083895-2-joannelkoong@gmail.com/
====================

Link: https://lore.kernel.org/r/20220822181023.3979645-1-joannelkoong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests/net: Add sk_bind_sendto_listen and sk_connect_zero_addr

This patch adds 2 new tests: sk_bind_sendto_listen and
sk_connect_zero_addr.

The sk_bind_sendto_listen test exercises the path where a socket's
rcv saddr changes after it has been added to the binding tables,
and then a listen() on the socket is invoked. The listen() should
succeed.

The sk_bind_sendto_listen test is copied over from one of syzbot's
tests: https://syzkaller.appspot.com/x/repro.c?x=1673a38df00000

The sk_connect_zero_addr test exercises the path where the socket was
never previously added to the binding tables and it gets assigned a
saddr upon a connect() to address 0.

Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

selftests/net: Add test for timing a bind request to a port with a populated bhash entry

This test populates the bhash table for a given port with
MAX_THREADS * MAX_CONNECTIONS sockets, and then times how long
a bind request on the port takes.

When populating the bhash table, we create the sockets and then bind
the sockets to the same address and port (SO_REUSEADDR and SO_REUSEPORT
are set). When timing how long a bind on the port takes, we bind on a
different address without SO_REUSEPORT set. We do not set SO_REUSEPORT
because we are interested in the case where the bind request does not
go through the tb->fastreuseport path, which is fragile (eg
tb->fastreuseport path does not work if binding with a different uid).

To run the script:
    Usage: ./bind_bhash.sh [-6 | -4] [-p port] [-a address]
    6: use ipv6
    4: use ipv4
    port: Port number
    address: ip address

Without any arguments, ./bind_bhash.sh defaults to ipv6 using ip address
"2001:0db8:0:f101::1" on port 443.

On my local machine, I see:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds

ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds

Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: Add a bhash2 table hashed by port and address

The current bind hashtable (bhash) is hashed by port only.
In the socket bind path, we have to check for bind conflicts by
traversing the specified port's inet_bind_bucket while holding the
hashbucket's spinlock (see inet_csk_get_port() and
inet_csk_bind_conflict()). In instances where there are tons of
sockets hashed to the same port at different addresses, the bind
conflict check is time-intensive and can cause softirq cpu lockups,
as well as stops new tcp connections since __inet_inherit_port()
also contests for the spinlock.

This patch adds a second bind table, bhash2, that hashes by
port and sk->sk_rcv_saddr (ipv4) and sk->sk_v6_rcv_saddr (ipv6).
Searching the bhash2 table leads to significantly faster conflict
resolution and less time holding the hashbucket spinlock.

Please note a few things:
* There can be the case where the a socket's address changes after it
has been bound. There are two cases where this happens:

  1) The case where there is a bind() call on INADDR_ANY (ipv4) or
  IPV6_ADDR_ANY (ipv6) and then a connect() call. The kernel will
  assign the socket an address when it handles the connect()

  2) In inet_sk_reselect_saddr(), which is called when rebuilding the
  sk header and a few pre-conditions are met (eg rerouting fails).

In these two cases, we need to update the bhash2 table by removing the
entry for the old address, and add a new entry reflecting the updated
address.

* The bhash2 table must have its own lock, even though concurrent
accesses on the same port are protected by the bhash lock. Bhash2 must
have its own lock to protect against cases where sockets on different
ports hash to different bhash hashbuckets but to the same bhash2
hashbucket.

This brings up a few stipulations:
  1) When acquiring both the bhash and the bhash2 lock, the bhash2 lock
  will always be acquired after the bhash lock and released before the
  bhash lock is released.

  2) There are no nested bhash2 hashbucket locks. A bhash2 lock is always
  acquired+released before another bhash2 lock is acquired+released.

* The bhash table cannot be superseded by the bhash2 table because for
bind requests on INADDR_ANY (ipv4) or IPV6_ADDR_ANY (ipv6), every socket
bound to that port must be checked for a potential conflict. The bhash
table is the only source of port->socket associations.

Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

netlink: fix some kernel-doc comments

Modify the comment of input parameter of nlmsg_ and nla_ function.

Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220824013621.365103-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ethernet: ti: davinci_mdio: fix build for mdio bitbang uses

davinci_mdio.c uses mdio bitbang APIs, so it should select
MDIO_BITBANG to prevent build errors.

arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_remove':
drivers/net/ethernet/ti/davinci_mdio.c:649: undefined reference to `free_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:545: undefined reference to `alloc_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_read':
drivers/net/ethernet/ti/davinci_mdio.c:236: undefined reference to `mdiobb_read'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_write':
drivers/net/ethernet/ti/davinci_mdio.c:253: undefined reference to `mdiobb_write'

Fixes: d04807b80691 ("net: ethernet: ti: davinci_mdio: Add workaround for errata i2329")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ravi Gunasekaran <r-gunasekaran@ti.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Sudip Mukherjee (Codethink) <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20220824024216.4939-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Documentation: sysctl: align cells in second content column

Stephen Rothwell reported htmldocs warning when merging net-next tree:

Documentation/admin-guide/sysctl/net.rst:37: WARNING: Malformed table.
Text in column margin in table line 4.

========= =================== = ========== ==================
Directory Content               Directory  Content
========= =================== = ========== ==================
802       E802 protocol         mptcp     Multipath TCP
appletalk Appletalk protocol    netfilter Network Filter
ax25      AX25                  netrom     NET/ROM
bridge    Bridging              rose      X.25 PLP layer
core      General parameter     tipc      TIPC
ethernet  Ethernet protocol     unix      Unix domain sockets
ipv4      IP version 4          x25       X.25 protocol
ipv6      IP version 6
========= =================== = ========== ==================

The warning above is caused by cells in second "Content" column of
/proc/sys/net subdirectory table which are in column margin.

Align these cells against the column header to fix the warning.

Link: https://lore.kernel.org/linux-next/20220823134905.57ed08d5@canb.auug.org.au/
Fixes: 1202cdd665315c ("Remove DECnet support from kernel")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://lore.kernel.org/r/20220824035804.204322-1-bagasdotme@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'r8169-next'

Heiner Kallweit says:

====================
r8169: remove support for few unused chip versions

There's a number of chip versions that apparently never made it to the
mass market. Detection of these chip versions has been disabled for
few kernel versions now and nobody complained. Therefore remove
support for these chip versions.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove support for chip version 60

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove support for chip version 50

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.

v3:
- rebase patch

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove support for chip version 49

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.

v2:
- fix a typo: RTL_GIGA_MAC_VER_40 -> RTL_GIGA_MAC_VER_50

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove support for chip versions 45 and 47

Detection of these chip versions has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove support for chip version 41

Detection of this chip version has been disabled for few kernel versions now.
Nobody complained, so remove support for this chip version.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-updates-2022-08-22' of git://git./linux/kernel/git/saeed/linux

mlx5-updates-2022-08-22

Roi Dayan Says:
===============
Add support for SF tunnel offload

Mlx5 driver only supports VF tunnel offload.
To add support for SF tunnel offload the driver needs to:
1. Add send-to-vport metadata matching rules like done for VFs.
2. Set an indirect table for SF vport, same as VF vport.

info smaller sub functions for better maintainability.

rules from esw init phase to representor load phase.
SFs could be created after esw initialized and thus the send-to-vport
meta rules would not be created for those SFs.
By moving the creation of the rules to representor load phase
we ensure creating the rules also for SFs created later.

===============

Lama Kayal Says:
================
Make flow steering API loosely coupled from mlx5e_priv, in a manner to
introduce more readable and maintainable modules.

Make TC's private, let mlx5e_flow_steering struct be dynamically allocated,
and introduce its API to maintain the code via setters and getters
instead of publicly exposing it.

Introduce flow steering debug macros to provide an elegant finish to the
decoupled flow steering API, where errors related to flow steering shall
be reported via them.

All flow steering related files will drop any coupling to mlx5e_priv,
instead they will get the relevant members as input. Among these,
fs_tt_redirect, fs_tc, and arfs.
================

micrel: ksz8851: fixes struct pointer issue

Issue found during code review. This bug has no impact as long as the
ks8851_net structure is the first element of the ks8851_net_spi structure.
As long as the offset to the ks8851_net struct is zero, the container_of()
macro is subtracting 0 and therefore no damage done. But if the
ks8851_net_spi struct is ever modified such that the ks8851_net struct
within it is no longer the first element of the struct, then the bug would
manifest itself and cause problems.

struct ks8851_net is contained within ks8851_net_spi.
ks is contained within kss.
kss is the priv_data of the netdev structure.

Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: annotate data-race around tcp_md5sig_pool_populated

tcp_md5sig_pool_populated can be read while another thread
changes its value.

The race has no consequence because allocations
are protected with tcp_md5sig_mutex.

This patch adds READ_ONCE() and WRITE_ONCE() to document
the race and silence KCSAN.

Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: marvell: prestera: implement br_port_locked flag offloading

Both <port> br_port_locked and <lag> interfaces's flag
offloading is supported. No new ABI is being added,
rather existing (port_param_set) API call gets extended.

Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
V2:
add missing receipents (linux-kernel, netdev)
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'j7200-support'

Siddharth Vadapalli says:

====================
J7200: CPSW5G: Add support for QSGMII mode to am65-cpsw driver

Add support for QSGMII mode to am65-cpsw driver.

Change log:

v4-> v5:
1. Move ti,j7200-cpswxg-nuss compatible to the line above the
   ti,j721e-cpsw-nuss compatible.
2. Add allOf and move if-then statements within it to allow future if-then
   statements to be added easily.

v3 -> v4:
1. Update bindings to disallow ports based on compatible, instead of
   adding a new if/then statement for the new compatible.
2. Add Else-If condition for RMII mode in the set of supported interfaces.
   Support for RMII mode is already present in the driver and I had
   missed out adding a condition for RMII mode in the previous patches.

v2 -> v3:
1. In ti,k3-am654-cpsw-nuss.yaml, restrict if/then statement to port
   nodes.

v1 -> v2:
1. Add new compatible for CPSW5G in ti,k3-am654-cpsw-nuss.yaml and extend
   properties for new compatible.
2. Add extra_modes member to struct am65_cpsw_pdata to be used for QSGMII
   mode by new compatible.
3. Add check for phylink supported modes to ensure that only one phy mode
   is advertised as supported.
4. Check if extra_modes supports QSGMII mode in am65_cpsw_nuss_mac_config()
   for register write.
5. Add check for assigning port->sgmii_base only when extra_modes is valid.

v4: https://lore.kernel.org/r/20220816060139.111934-1-s-vadapalli@ti.com/
v3: https://lore.kernel.org/r/20220606110443.30362-1-s-vadapalli@ti.com/
v2: https://lore.kernel.org/r/20220602114558.6204-1-s-vadapalli@ti.com/
v1: https://lore.kernel.org/r/20220531113058.23708-1-s-vadapalli@ti.com/
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: am65-cpsw: Move phy_set_mode_ext() to correct location

In TI's J7200 SoC CPSW5G ports, each of the 4 ports can be configured
as a QSGMII main or QSGMII-SUB port. This configuration is performed
by phy-gmii-sel driver on invoking the phy_set_mode_ext() function.

It is necessary for the QSGMII main port to be configured before any of
the QSGMII-SUB interfaces are brought up. Currently, the QSGMII-SUB
interfaces come up before the QSGMII main port is configured.

Fix this by moving the call to phy_set_mode_ext() from
am65_cpsw_nuss_ndo_slave_open() to am65_cpsw_nuss_init_slave_ports(),
thereby ensuring that the QSGMII main port is configured before any of
the QSGMII-SUB ports are brought up.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: am65-cpsw: Add support for J7200 CPSW5G

CPSW5G in J7200 supports additional modes like QSGMII and SGMII.
Add new compatible for J7200 and enable QSGMII mode in am65-cpsw driver.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: ti: k3-am654-cpsw-nuss: Update bindings for J7200 CPSW5G

Update bindings for TI K3 J7200 SoC which contains 5 ports (4 external
ports) CPSW5G module and add compatible for it.

Changes made:
    - Add new compatible ti,j7200-cpswxg-nuss for CPSW5G.
    - Extend pattern properties for new compatible.
    - Change maximum number of CPSW ports to 4 for new compatible.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: skb: prevent the split of kfree_skb_reason() by gcc

Sometimes, gcc will optimize the function by spliting it to two or
more functions. In this case, kfree_skb_reason() is splited to
kfree_skb_reason and kfree_skb_reason.part.0. However, the
function/tracepoint trace_kfree_skb() in it needs the return address
of kfree_skb_reason().

This split makes the call chains becomes:
kfree_skb_reason() -> kfree_skb_reason.part.0 -> trace_kfree_skb()

which makes the return address that passed to trace_kfree_skb() be
kfree_skb().

Therefore, introduce '__fix_address', which is the combination of
'__noclone' and 'noinline', and apply it to kfree_skb_reason() to
prevent to from being splited or made inline.

(Is it better to simply apply '__noclone oninline' to kfree_skb_reason?
I'm thinking maybe other functions have the same problems)

Meanwhile, wrap 'skb_unref()' with 'unlikely()', as the compiler thinks
it is likely return true and splits kfree_skb_reason().

Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'add-interface-mode-select-and-rmii'

Wei Fang says:

====================
add interface mode select and RMII

From: Wei Fang <wei.fang@nxp.com>

The patches add the below feature support for both TJA1100 and
TJA1101 PHYs cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.
====================

Link: https://lore.kernel.org/r/20220822015949.1569969-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: tja11xx: add interface mode and RMII REF_CLK support

Add below features support for both TJA1100 and TJA1101 cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dt-bindings: net: tja11xx: add nxp,refclk_in property

TJA110x REF_CLK can be configured as interface reference clock
intput or output when the RMII mode enabled. This patch add the
property to make the REF_CLK can be configurable.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'mlxsw-introduce-modular-system-support-by-minimal-driver'

Petr Machata says:

====================
mlxsw: Introduce modular system support by minimal driver

Vadim Pasternak writes:

This patchset adds line cards support in mlxsw_minimal, which is used
for monitoring purposes on BMC systems. The BMC is connected to the
ASIC over I2C bus, unlike the host CPU that is connected to the ASIC
via PCI bus.

The BMC system needs to be notified whenever line cards become active
or inactive, so that, for example, netdevs will be registered /
unregistered by mlxsw_minimal. However, traps cannot be generated
towards the BMC over the I2C bus. To overcome that, the I2C bus driver
(i.e., mlxsw_i2c) registers an handler for an IRQ that is fired upon
specific system wide changes, like line card activation and
deactivation.

The generated event is handled by mlxsw_core, which checks whether
anything changed in the state of available line cards. If a line card
becomes active or inactive, interested parties such as mlxsw_minimal
are notified via their registered line card event callback.

Patch set overview:

Patches #1 is preparations.

Patches #2-#3 extend mlxsw_core with an infrastructure to handle the
previously mentioned system events.

Patch #4 extends the I2C bus driver to register an handler for the IRQ
fired upon specific system wide changes.

Patches #5-#8 gradually add line cards support in mlxsw_minimal by
dynamically registering / unregistering netdevs for ports found on
line cards, whenever a line card becomes active / inactive.
====================

Link: https://lore.kernel.org/r/cover.1661093502.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: minimal: Extend to support line card dynamic operations

Implement line card operation callbacks got_active() / got_inactive().
The purpose of these callback to create / remove line card ports after
line card is getting active / inactive.

Implement line ports_remove_selected() callback to support line card
un-provisioning flow through 'devlink'.

Add line card operation registration and de-registration APIs.

Add module offset for line card. Offset for main board iz zero.
For line card in slot #n offset is calculated as (#n - 1) multiplied by
maximum modules number.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: minimal: Extend module to port mapping with slot index

The interfaces for ports found on line card are created and removed
dynamically after line card is getting active or inactive.

Introduce per line card array with module to port mapping.
For each port get 'slot_index' through PMLP register and set port
mapping for the relevant [slot_index][module] entry.

Split module and port allocation into separate routines.

Split per line card port creation and removing into separate routines.
Motivation to re-use these routines for line card operations.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: minimal: Move ports allocation to separate routine

Perform ports allocation in a separate routine.
Motivation is to re-use this routine for ports found on line cards.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: minimal: Extend APIs with slot index for modular system support

Add 'slot_index' field to port structure.
Replace zero slot_index argument with 'slot_index' in 'ethtool'
related APIs.
Add 'slot_index' argument to port initialization and
de-initialization related APIs.

Motivation is to prepare minimal driver for modular system support.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: i2c: Add support for system interrupt handling

Extend i2c bus driver with interrupt handler to support system specific
hotplug events, related to line card state change.

Provide system IRQ line for interrupt handler. IRQ line Id could be
provided through the platform data if available, or could be set to the
default value.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: core_linecards: Register a system event handler

Add line card system event handler. Register it with core. It is
triggered by system interrupts raised from chassis programmable logic
devices to CPU. The purpose is to handle line card state changes over
I2C bus.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: core: Add registration APIs for system event handler

The purpose of system event handler is to handle system interrupts.
Such interrupts are raised to CPU from system programmable logic
devices, upon specific system wide changes, like line card activation
and deactivation.

The purpose is to create an alternative to trap mechanism, which
delivers these events to driver over PCI bus, but not available for
the driver working over I2C bus.

Mechanism is system dependent and applicable only for the systems
equipped with programmable devices with custom logic.

Add APIs for event handler registration and un-registration and API
which should be invoked from the registered callbacks when system
interrupt is raised to CPU.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlxsw: core_linecards: Separate line card init and fini flow

Currently, each line card is initialized using the following steps:

1. Initializing its various fields (e.g., slot index).
2. Creating the corresponding devlink object.
3. Enabling events (i.e., traps) for changes in line card status.
4. Querying and processing line card status.

Unlike traps, the IRQ that notifies the CPU about line card status
changes cannot be enabled / disabled on a per line card basis.

If a handler is registered before the line cards are initialized, the
handler risks accessing uninitialized memory.

On the other hand, if the handler is registered after initialization,
we risk missing events. For example, in step 4, the driver might see
that a line card is in ready state and will tell the device to enable
it. When enablement is done, the line card will be activated and the
IRQ will be triggered. Since a handler was not registered, the event
will be missed.

Solve this by splitting the initialization sequence into two steps
(1-2 and 3-4). In a subsequent patch, the handler will be registered
between both steps.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

docs: netlink: basic introduction to Netlink

Provide a bit of a brain dump of netlink related information
as documentation. Hopefully this will be useful to people
trying to navigate implementing YAML based parsing in languages
we won't be able to help with.

I started writing this doc while trying to figure out what
it'd take to widen the applicability of YAML to good old rtnl,
but the doc grew beyond that as it usually happens.

In all honesty a lot of this information is new to me as I usually
follow the "copy an existing example, drink to forget" process
of writing netlink user space, so reviews will be much appreciated.

Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20220819200221.422801-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: improve and fix netlink kdoc

Subsequent patch will render the kdoc from
include/uapi/linux/netlink.h into Documentation.
We need to fix the warnings. While at it move
the comments on struct nlmsghdr to a proper
kdoc comment.

Link: https://lore.kernel.org/r/20220819200221.422801-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: ftmac100: set max_mtu to allow DSA overhead setting

In case ftmac100 is used with a DSA switch, Linux wants to set MTU
to 1504 to accommodate for DSA overhead. With the default max_mtu
it leads to the error message:
ftmac100 92000000.mac eth0: error -22 setting MTU to 1504 to include DSA overhead

ftmac100 supports packet length 1518 (MAX_PKT_SIZE constant), so it is
safe to report it in max_mtu.

Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220821160844.474277-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch 'dsa-changes-for-multiple-cpu-ports-part-3'

Vladimir Oltean says:

====================
DSA changes for multiple CPU ports (part 3)

Those who have been following part 1:
https://patchwork.kernel.org/project/netdevbpf/cover/20220511095020.562461-1-vladimir.oltean@nxp.com/
and part 2:
https://patchwork.kernel.org/project/netdevbpf/cover/20220521213743.2735445-1-vladimir.oltean@nxp.com/
will know that I am trying to enable the second internal port pair from
the NXP LS1028A Felix switch for DSA-tagged traffic via "ocelot-8021q".
This series represents part 3 of that effort.

Covered here are some preparations in DSA for handling multiple DSA
masters:
- when changing the tagging protocol via sysfs
- when the masters go down
as well as preparation for monitoring the upper devices of a DSA master
(to support DSA masters under a LAG).

There are also 2 small preparations for the ocelot driver, for the case
where multiple tag_8021q CPU ports are used in a LAG. Both those changes
have to do with PGID forwarding domains.

Compared to v1, the patches were trimmed down to just another
preparation stage, and the UAPI changes were pushed further out to part 4.
https://patchwork.kernel.org/project/netdevbpf/cover/20220523104256.3556016-1-olteanv@gmail.com/

Compared to v2, I had to export a symbol I forgot to
(ocelot_port_teardown_dsa_8021q_cpu), to avoid a build breakage when the
felix and seville drivers are built as modules.
====================

Link: https://lore.kernel.org/r/20220819174820.3585002-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: mscc: ocelot: adjust forwarding domain for CPU ports in a LAG

Currently when we have 2 CPU ports configured for DSA tag_8021q mode and
we put them in a LAG, a PGID dump looks like this:

PGID_SRC[0] = ports 4,
PGID_SRC[1] = ports 4,
PGID_SRC[2] = ports 4,
PGID_SRC[3] = ports 4,
PGID_SRC[4] = ports 0, 1, 2, 3, 4, 5,
PGID_SRC[5] = no ports

(ports 0-3 are user ports, ports 4 and 5 are CPU ports)

There are 2 problems with the configuration above:

- user ports should enable forwarding towards both CPU ports, not just 4,
  and the aggregation PGIDs should prune one CPU port or the other from
  the destination port mask, based on a hash computed from packet headers.

- CPU ports should not be allowed to forward towards themselves and also
  not towards other ports in the same LAG as themselves

The first problem requires fixing up the PGID_SRC of user ports, when
ocelot_port_assigned_dsa_8021q_cpu_mask() is called. We need to say that
when a user port is assigned to a tag_8021q CPU port and that port is in
a LAG, it should forward towards all ports in that LAG.

The second problem requires fixing up the PGID_SRC of port 4, to remove
ports 4 and 5 (in a LAG) from the allowed destinations.

After this change, the PGID source masks look as follows:

PGID_SRC[0] = ports 4, 5,
PGID_SRC[1] = ports 4, 5,
PGID_SRC[2] = ports 4, 5,
PGID_SRC[3] = ports 4, 5,
PGID_SRC[4] = ports 0, 1, 2, 3,
PGID_SRC[5] = no ports

Note that PGID_SRC[5] still looks weird (it should say "0, 1, 2, 3" just
like PGID_SRC[4] does), but I've tested forwarding through this CPU port
and it doesn't seem like anything is affected (it appears that PGID_SRC[4]
is being looked up on forwarding from the CPU, since both ports 4 and 5
have logical port ID 4). The reason why it looks weird is because
we've never called ocelot_port_assign_dsa_8021q_cpu() for any user port
towards port 5 (all user ports are assigned to port 4 which is in a LAG
with 5).

Since things aren't broken, I'm willing to leave it like that for now
and just document the oddity.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: mscc: ocelot: set up tag_8021q CPU ports independent of user port affinity

This is a partial revert of commit c295f9831f1d ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.

Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.

In turn, this makes 2 undesirable things happen:

(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
ocelot for VLAN-unaware bridging

To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.

All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: use dsa_tree_for_each_cpu_port in dsa_tree_{setup,teardown}_master

More logic will be added to dsa_tree_setup_master() and
dsa_tree_teardown_master() in upcoming changes.

Reduce the indentation by one level in these functions by introducing
and using a dedicated iterator for CPU ports of a tree.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: all DSA masters must be down when changing the tagging protocol

The fact that the tagging protocol is set and queried from the
/sys/class/net/<dsa-master>/dsa/tagging file is a bit of a quirk from
the single CPU port days which isn't aging very well now that DSA can
have more than a single CPU port. This is because the tagging protocol
is a switch property, yet in the presence of multiple CPU ports it can
be queried and set from multiple sysfs files, all of which are handled
by the same implementation.

The current logic ensures that the net device whose sysfs file we're
changing the tagging protocol through must be down. That net device is
the DSA master, and this is fine for single DSA master / CPU port setups.

But exactly because the tagging protocol is per switch [ tree, in fact ]
and not per DSA master, this isn't fine any longer with multiple CPU
ports, and we must iterate through the tree and find all DSA masters,
and make sure that all of them are down.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: only bring down user ports assigned to a given DSA master

This is an adaptation of commit c0a8a9c27493 ("net: dsa: automatically
bring user ports down when master goes down") for multiple DSA masters.
When a DSA master goes down, only the user ports under its control
should go down too, the others can still send/receive traffic.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: existing DSA masters cannot join upper interfaces

All the traffic to/from a DSA master is supposed to be distributed among
its DSA switch upper interfaces, so we should not allow other upper
device kinds.

An exception to this is DSA_TAG_PROTO_NONE (switches with no DSA tags),
and in that case it is actually expected to create e.g. VLAN interfaces
on the master. But for those, netdev_uses_dsa(master) returns false, so
the restriction doesn't apply.

The motivation for this change is to allow LAG interfaces of DSA masters
to be DSA masters themselves. We want to restrict the user's degrees of
freedom by 1: the LAG should already have all DSA masters as lowers, and
while lower ports of the LAG can be removed, none can be added after the
fact.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: bridge: move DSA master bridging restriction to DSA

When DSA gains support for multiple CPU ports in a LAG, it will become
mandatory to monitor the changeupper events for the DSA master.

In fact, there are already some restrictions to be imposed in that area,
namely that a DSA master cannot be a bridge port except in some special
circumstances.

Centralize the restrictions at the level of the DSA layer as a
preliminary step.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: don't stop at NOTIFY_OK when calling ds->ops->port_prechangeupper

dsa_slave_prechangeupper_sanity_check() is supposed to enforce some
adjacency restrictions, and calls ds->ops->port_prechangeupper if the
driver implements it.

We convert the error code from the port_prechangeupper() call to a
notifier code, and 0 is converted to NOTIFY_OK, but the caller of
dsa_slave_prechangeupper_sanity_check() stops at any notifier code
different from NOTIFY_DONE.

Avoid this by converting back the notifier code to an error code, so
that both NOTIFY_OK and NOTIFY_DONE will be seen as 0. This allows more
parallel sanity check functions to be added.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

net: dsa: walk through all changeupper notifier functions

Traditionally, DSA has had a single netdev notifier handling function
for each device type.

For the sake of code cleanliness, we would like to introduce more
handling functions which do one thing, but the conditions for entering
these functions start to overlap. Example: a handling function which
tracks whether any bridges contain both DSA and non-DSA interfaces.
Either this is placed before dsa_slave_changeupper(), case in which it
will prevent that function from executing, or we place it after
dsa_slave_changeupper(), case in which we will prevent it from
executing. The other alternative is to ignore errors from the new
handling function (not ideal).

To support this usage, we need to change the pattern. In the new model,
we enter all notifier handling sub-functions, and exit with NOTIFY_DONE
if there is nothing to do. This allows the sub-functions to be
relatively free-form and independent from each other.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Merge branch 'vsock-updates-for-so_rcvlowat-handling'

Arseniy Krasnov says:

====================
vsock: updates for SO_RCVLOWAT handling

This patchset includes some updates for SO_RCVLOWAT:

1) af_vsock:
   During my experiments with zerocopy receive, i found, that in some
   cases, poll() implementation violates POSIX: when socket has non-
   default SO_RCVLOWAT(e.g. not 1), poll() will always set POLLIN and
   POLLRDNORM bits in 'revents' even number of bytes available to read
   on socket is smaller than SO_RCVLOWAT value. In this case,user sees
   POLLIN flag and then tries to read data(for example using  'read()'
   call), but read call will be blocked, because  SO_RCVLOWAT logic is
   supported in dequeue loop in af_vsock.c. But the same time,  POSIX
   requires that:

   "POLLIN     Data other than high-priority data may be read without
               blocking.
    POLLRDNORM Normal data may be read without blocking."

   See https://www.open-std.org/jtc1/sc22/open/n4217.pdf, page 293.

   So, we have, that poll() syscall returns POLLIN, but read call will
   be blocked.

   Also in man page socket(7) i found that:

   "Since Linux 2.6.28, select(2), poll(2), and epoll(7) indicate a
   socket as readable only if at least SO_RCVLOWAT bytes are available."

   I checked TCP callback for poll()(net/ipv4/tcp.c, tcp_poll()), it
   uses SO_RCVLOWAT value to set POLLIN bit, also i've tested TCP with
   this case for TCP socket, it works as POSIX required.

   I've added some fixes to af_vsock.c and virtio_transport_common.c,
   test is also implemented.

2) virtio/vsock:
   It adds some optimization to wake ups, when new data arrived. Now,
   SO_RCVLOWAT is considered before wake up sleepers who wait new data.
   There is no sense, to kick waiter, when number of available bytes
   in socket's queue < SO_RCVLOWAT, because if we wake up reader in
   this case, it will wait for SO_RCVLOWAT data anyway during dequeue,
   or in poll() case, POLLIN/POLLRDNORM bits won't be set, so such
   exit from poll() will be "spurious". This logic is also used in TCP
   sockets.

3) vmci/vsock:
   Same as 2), but i'm not sure about this changes. Will be very good,
   to get comments from someone who knows this code.

4) Hyper-V:
   As Dexuan Cui mentioned, for Hyper-V transport it is difficult to
   support SO_RCVLOWAT, so he suggested to disable this feature for
   Hyper-V.
====================

Link: https://lore.kernel.org/r/de41de4c-0345-34d7-7c36-4345258b7ba8@sberdevices.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

vsock_test: POLLIN + SO_RCVLOWAT test

This adds test to check, that when poll() returns POLLIN, POLLRDNORM bits,
next read call won't block.

Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

vmci/vsock: check SO_RCVLOWAT before wake up reader

This adds extra condition to wake up data reader: do it only when number
of readable bytes >= SO_RCVLOWAT. Otherwise, there is no sense to kick
user, because it will wait until SO_RCVLOWAT bytes will be dequeued. This
check is performed in vsock_data_ready().

Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

virtio/vsock: check SO_RCVLOWAT before wake up reader

This adds extra condition to wake up data reader: do it only when number
of readable bytes >= SO_RCVLOWAT. Otherwise, there is no sense to kick
user,because it will wait until SO_RCVLOWAT bytes will be dequeued. This
check is performed in vsock_data_ready().

Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>