ixgbe: fix unbalanced device enable/disable in suspend/resume

commit debb9df311582c83fe369baa35fa4b92e8a9c58a upstream.

pci_disable_device() called in __ixgbe_shutdown() decreases
dev->enable_cnt by 1. pci_enable_device_mem() which increases
dev->enable_cnt by 1, was removed from ixgbe_resume() in commit
6f82b2558735 ("ixgbe: use generic power management"). This caused
unbalanced increase/decrease. So add pci_enable_device_mem() back.

Fix the following call trace.

  ixgbe 0000:17:00.1: disabling already-disabled device
  Call Trace:
   __ixgbe_shutdown+0x10a/0x1e0 [ixgbe]
   ixgbe_suspend+0x32/0x70 [ixgbe]
   pci_pm_suspend+0x87/0x160
   ? pci_pm_freeze+0xd0/0xd0
   dpm_run_callback+0x42/0x170
   __device_suspend+0x114/0x460
   async_suspend+0x1f/0xa0
   async_run_entry_fn+0x3c/0xf0
   process_one_work+0x1dd/0x410
   worker_thread+0x34/0x3f0
   ? cancel_delayed_work+0x90/0x90
   kthread+0x14c/0x170
   ? kthread_park+0x90/0x90
   ret_from_fork+0x1f/0x30

Fixes: 6f82b2558735 ("ixgbe: use generic power management")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: libsas: Reset num_scatter if libata marks qc as NODATA

commit 176ddd89171ddcf661862d90c5d257877f7326d6 upstream.

When the cache_type for the SCSI device is changed, the SCSI layer issues a
MODE_SELECT command. The caching mode details are communicated via a
request buffer associated with the SCSI command with data direction set as
DMA_TO_DEVICE (scsi_mode_select()). When this command reaches the libata
layer, as a part of generic initial setup, libata layer sets up the
scatterlist for the command using the SCSI command (ata_scsi_qc_new()).
This command is then translated by the libata layer into
ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat()). The libata layer treats
this as a non-data command (ata_mselect_caching()), since it only needs an
ATA taskfile to pass the caching on/off information to the device. It does
not need the scatterlist that has been setup, so it does not perform
dma_map_sg() on the scatterlist (ata_qc_issue()). Unfortunately, when this
command reaches the libsas layer (sas_ata_qc_issue()), libsas layer sees it
as a non-data command with a scatterlist. It cannot extract the correct DMA
length since the scatterlist has not been mapped with dma_map_sg() for a
DMA operation. When this partially constructed SAS task reaches pm80xx
LLDD, it results in the following warning:

"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"

Update libsas to handle ATA non-data commands separately so num_scatter and
total_xfer_len remain 0.

Link: https://lore.kernel.org/r/20210318225632.2481291-1-jollys@google.com
Fixes: 53de092f47ff ("scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA")
Tested-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jolly Shah <jollys@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

riscv: Fix spelling mistake "SPARSEMEM" to "SPARSMEM"

commit 199fc6b8dee7d6d50467a57e0dc7e3e1b7d59966 upstream.

There is a spelling mistake when SPARSEMEM Kconfig copy.

Fixes: a5406a7ff56e ("riscv: Correct SPARSEMEM configuration")
Cc: stable@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfio/pci: Add missing range check in vfio_pci_mmap

commit 909290786ea335366e21d7f1ed5812b90f2f0a92 upstream.

When mmaping an extra device region verify that the region index
derived from the mmap offset is valid.

Fixes: a15b1883fee1 ("vfio_pci: Allow mapping extra regions")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Message-Id: <20210412214124.GA241759@lisa.in-ulm.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: alternatives: Move length validation in alternative_{insn, endif}

commit 22315a2296f4c251fa92aec45fbbae37e9301b6c upstream.

After commit 2decad92f473 ("arm64: mte: Ensure TIF_MTE_ASYNC_FAULT is
set atomically"), LLVM's integrated assembler fails to build entry.S:

<instantiation>:5:7: error: expected assembly-time absolute expression
 .org . - (664b-663b) + (662b-661b)
      ^
<instantiation>:6:7: error: expected assembly-time absolute expression
 .org . - (662b-661b) + (664b-663b)
      ^

The root cause is LLVM's assembler has a one-pass design, meaning it
cannot figure out these instruction lengths when the .org directive is
outside of the subsection that they are in, which was changed by the
.arch_extension directive added in the above commit.

Apply the same fix from commit 966a0acce2fc ("arm64/alternatives: move
length validation inside the subsection") to the alternative_endif
macro, shuffling the .org directives so that the length validation
happen will always happen in the same subsections. alternative_insn has
not shown any issue yet but it appears that it could have the same issue
in the future so just preemptively change it.

Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences")
Cc: <stable@vger.kernel.org> # 5.8.x
Link: https://github.com/ClangBuiltLinux/linux/issues/1347
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20210414000803.662534-1-nathan@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: fix inline asm in load_unaligned_zeropad()

commit 185f2e5f51c2029efd9dd26cceb968a44fe053c6 upstream.

The inline asm's addr operand is marked as input-only, however in
the case where an exception is taken it may be modified by the BIC
instruction on the exception path. Fix the problem by using a temporary
register as the destination register for the BIC instruction.

Signed-off-by: Peter Collingbourne <pcc@google.com>
Cc: stable@vger.kernel.org
Link: https://linux-review.googlesource.com/id/I84538c8a2307d567b4f45bb20b715451005f9617
Link: https://lore.kernel.org/r/20210401165110.3952103-1-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

readdir: make sure to verify directory entry for legacy interfaces too

commit 0c93ac69407d63a85be0129aa55ffaec27ffebd3 upstream.

This does the directory entry name verification for the legacy
"fillonedir" (and compat) interface that goes all the way back to the
dark ages before we had a proper dirent, and the readdir() system call
returned just a single entry at a time.

Nobody should use this interface unless you still have binaries from
1991, but let's do it right.

This came up during discussions about unsafe_copy_to_user() and proper
checking of all the inputs to it, as the networking layer is looking to
use it in a few new places.  So let's make sure the _old_ users do it
all right and proper, before we add new ones.

See also commit 8a23eb804ca4 ("Make filldir[64]() verify the directory
entry filename is valid") which did the proper modern interfaces that
people actually use. It had a note:

    Note that I didn't bother adding the checks to any legacy interfaces
    that nobody uses.

which this now corrects.  Note that we really don't care about POSIX and
the presense of '/' in a directory entry, but verify_dirent_name() also
ends up doing the proper name length verification which is what the
input checking discussion was about.

[ Another option would be to remove the support for this particular very
  old interface: any binaries that use it are likely a.out binaries, and
  they will no longer run anyway since we removed a.out binftm support
  in commit eac616557050 ("x86: Deprecate a.out support").

  But I'm not sure which came first: getdents() or ELF support, so let's
  pretend somebody might still have a working binary that uses the
  legacy readdir() case.. ]

Link: https://lore.kernel.org/lkml/CAHk-=wjbvzCAhAtvG0d81W5o0-KT5PPTHhfJ5ieDFq+bGtgOYg@mail.gmail.com/
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm verity fec: fix misaligned RS roots IO

commit 8ca7cab82bda4eb0b8064befeeeaa38106cac637 upstream.

commit df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to
block size") introduced the possibility for misaligned roots IO
relative to the underlying device's logical block size. E.g. Android's
default RS roots=2 results in dm_bufio->block_size=1024, which causes
the following EIO if the logical block size of the device is 4096,
given v->data_dev_block_bits=12:

E sd 0    : 0:0:0: [sda] tag#30 request not aligned to the logical block size
E blk_update_request: I/O error, dev sda, sector 10368424 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
E device-mapper: verity-fec: 254:8: FEC 9244672: parity read failed (block 18056): -5

Fix this by onlu using f->roots for dm_bufio blocksize IFF it is
aligned to v->data_dev_block_bits.

Fixes: df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to block size")
Cc: stable@vger.kernel.org
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: wacom: set EV_KEY and EV_ABS only for non-HID_GENERIC type of devices

commit 276559d8d02c2709281578976ca2f53bc62063d4 upstream.

Valid HID_GENERIC type of devices set EV_KEY and EV_ABS by wacom_map_usage.
When *_input_capabilities are reached, those devices should already have
their proper EV_* set. EV_KEY and EV_ABS only need to be set for
non-HID_GENERIC type of devices in *_input_capabilities.

Devices that don't support HID descitoprs will pass back to hid-input for
registration without being accidentally rejected by the introduction of
patch: "Input: refuse to register absolute devices without absinfo"

Fixes: 6ecfe51b4082 ("Input: refuse to register absolute devices without absinfo")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Tested-by: Juan Garrido <Juan.Garrido@wacom.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: i8042 - fix Pegatron C15B ID entry

commit daa58c8eec0a65ac8e2e77ff3ea8a233d8eec954 upstream.

The Zenbook Flip entry that was added overwrites a previous one
because of a typo:

In file included from drivers/input/serio/i8042.h:23,
                 from drivers/input/serio/i8042.c:131:
drivers/input/serio/i8042-x86ia64io.h:591:28: error: initialized field overwritten [-Werror=override-init]
  591 |                 .matches = {
      |                            ^
drivers/input/serio/i8042-x86ia64io.h:591:28: note: (near initialization for 'i8042_dmi_noselftest_table[0].matches')

Add the missing separator between the two.

Fixes: b5d6e7ab7fe7 ("Input: i8042 - add ASUS Zenbook Flip to noselftest list")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Link: https://lore.kernel.org/r/20210323130623.2302402-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: s6sy761 - fix coordinate read bit shift

commit 30b3f68715595dee7fe4d9bd91a2252c3becdf0a upstream.

The touch coordinate register contains the following:

        byte 3             byte 2             byte 1
+--------+--------+ +-----------------+ +-----------------+
|        |        | |                 | |                 |
| X[3:0] | Y[3:0] | |     Y[11:4]     | |     X[11:4]     |
|        |        | |                 | |                 |
+--------+--------+ +-----------------+ +-----------------+

Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.

This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).

Fixes: 0145a7141e59 ("Input: add support for the Samsung S6SY761 touchscreen")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib: fix kconfig dependency on ARCH_WANT_FRAME_POINTERS

[ Upstream commit 7d37cb2c912dc5c25ffac784a4f9b98c06c6bd08 ]

When LATENCYTOP, LOCKDEP, or FAULT_INJECTION_STACKTRACE_FILTER is
enabled and ARCH_WANT_FRAME_POINTERS is disabled, Kbuild gives a warning
such as:

  WARNING: unmet direct dependencies detected for FRAME_POINTER
    Depends on [n]: DEBUG_KERNEL [=y] && (M68K || UML || SUPERH) || ARCH_WANT_FRAME_POINTERS [=n] || MCOUNT [=n]
    Selected by [y]:
    - LATENCYTOP [=y] && DEBUG_KERNEL [=y] && STACKTRACE_SUPPORT [=y] && PROC_FS [=y] && !MIPS && !PPC && !S390 && !MICROBLAZE && !ARM && !ARC && !X86

Depending on ARCH_WANT_FRAME_POINTERS causes a recursive dependency
error.  ARCH_WANT_FRAME_POINTERS is to be selected by the architecture,
and is not supposed to be overridden by other config options.

Link: https://lkml.kernel.org/r/20210329165329.27994-1-julianbraha@gmail.com
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

virt_wifi: Return micros for BSS TSF values

[ Upstream commit b57aa17f07c9270e576ef7df09f142978b5a75f0 ]

cfg80211_inform_bss expects to receive a TSF value, but is given the
time since boot in nanoseconds. TSF values are expected to be at
microsecond scale rather than nanosecond scale.

Signed-off-by: A. Cody Schuffelen <schuffelen@google.com>
Link: https://lore.kernel.org/r/20210318200419.1421034-1-schuffelen@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac80211: clear sta->fast_rx when STA removed from 4-addr VLAN

[ Upstream commit dd0b45538146cb6a54d6da7663b8c3afd16ebcfd ]

In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.

Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.

[  239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[  239.449531] pgd = 80204000
...
[  239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[  239.481591] Hardware name: Generic DT based system
[  239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[  239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[  239.497823] LR is at 0xbe08fc54
...
[  239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[  239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[  239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[  239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
            0211])
[  239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[  239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[  239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
            )
[  239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[  239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[  239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[  239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[  239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[  239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)

Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pcnet32: Use pci_resource_len to validate PCI resource

[ Upstream commit 66c3f05ddc538ee796321210c906b6ae6fc0792a ]

pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.

pci 0000:00:01.0: reg 0x10: [io  0x0000-0x001f]
pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000001f]
...
pcnet32: card has no PCI IO resources, aborting

Use pci_resouce_len() instead.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: forbid monitor for add llsec seclevel

[ Upstream commit 9ec87e322428d4734ac647d1a8e507434086993d ]

This patch forbids to add llsec seclevel for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-14-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: stop dump llsec seclevels for monitors

[ Upstream commit 4c9b4f55ad1f5a4b6206ac4ea58f273126d21925 ]

This patch stops dumping llsec seclevels for monitors which we don't
support yet. Otherwise we will access llsec mib which isn't initialized
for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-13-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: forbid monitor for del llsec devkey

[ Upstream commit 6fb8045319ef172dc88a8142e7f8b58c7608137e ]

This patch forbids to del llsec devkey for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-12-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: forbid monitor for add llsec devkey

[ Upstream commit a347b3b394868fef15b16f143719df56184be81d ]

This patch forbids to add llsec devkey for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-11-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: stop dump llsec devkeys for monitors

[ Upstream commit 080d1a57a94d93e70f84b7a360baa351388c574f ]

This patch stops dumping llsec devkeys for monitors which we don't support
yet. Otherwise we will access llsec mib which isn't initialized for
monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-10-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: forbid monitor for del llsec dev

[ Upstream commit ad8f9de1f3566686af35b1c6b43240726541da61 ]

This patch forbids to del llsec dev for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-9-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: forbid monitor for add llsec dev

[ Upstream commit 5303f956b05a2886ff42890908156afaec0f95ac ]

This patch forbids to add llsec dev for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-8-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: stop dump llsec devs for monitors

[ Upstream commit 5582d641e6740839c9b83efd1fbf9bcd00b6f5fc ]

This patch stops dumping llsec devs for monitors which we don't support
yet. Otherwise we will access llsec mib which isn't initialized for
monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-7-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: forbid monitor for del llsec key

[ Upstream commit b6e2949544a183f590ae6f3ef2d1aaaa2c44e38a ]

This patch forbids to del llsec key for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-6-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: forbid monitor for add llsec key

[ Upstream commit 08470c5453339369bd3d590c4cbb0b5961cdcbb6 ]

This patch forbids to add llsec key for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-5-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: stop dump llsec keys for monitors

[ Upstream commit fb3c5cdf88cd504ef11d59e8d656f4bc896c6922 ]

This patch stops dumping llsec keys for monitors which we don't support
yet. Otherwise we will access llsec mib which isn't initialized for
monitors.

Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-4-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: add support for Qu with AX201 device

[ Upstream commit 97195d3cad852063208a1cd4f4d073459547a415 ]

Add this specific Samsung AX201 sku to driver so it can be
detected and initialized successfully.

Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210326125611.30b622037714.Id9fd709cf1c8261c097bbfd7453f6476077dcafc@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: scsi_transport_srp: Don't block target in SRP_PORT_LOST state

[ Upstream commit 5cd0f6f57639c5afbb36100c69281fee82c95ee7 ]

rport_dev_loss_timedout() sets the rport state to SRP_PORT_LOST and the
SCSI target state to SDEV_TRANSPORT_OFFLINE. If this races with
srp_reconnect_work(), a warning is printed:

Mar 27 18:48:07 ictm1604s01h4 kernel: dev_loss_tmo expired for SRP port-18:1 / host18.
Mar 27 18:48:07 ictm1604s01h4 kernel: ------------[ cut here ]------------
Mar 27 18:48:07 ictm1604s01h4 kernel: scsi_internal_device_block(18:0:0:100) failed: ret = -22
Mar 27 18:48:07 ictm1604s01h4 kernel: Call Trace:
Mar 27 18:48:07 ictm1604s01h4 kernel:  ? scsi_target_unblock+0x50/0x50 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel:  starget_for_each_device+0x80/0xb0 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel:  target_block+0x24/0x30 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel:  device_for_each_child+0x57/0x90
Mar 27 18:48:07 ictm1604s01h4 kernel:  srp_reconnect_rport+0xe4/0x230 [scsi_transport_srp]
Mar 27 18:48:07 ictm1604s01h4 kernel:  srp_reconnect_work+0x40/0xc0 [scsi_transport_srp]

Avoid this by not trying to block targets for rports in SRP_PORT_LOST
state.

Link: https://lore.kernel.org/r/20210401091105.8046-1-mwilck@suse.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_esai: Fix TDM slot setup for I2S mode

[ Upstream commit e7a48c710defa0e0fef54d42b7d9e4ab596e2761 ]

When using the driver in I2S TDM mode, the fsl_esai_startup()
function rewrites the number of slots previously set by the
fsl_esai_set_dai_tdm_slot() function to 2.
To fix this, let's use the saved slot count value or, if TDM
is not used and the number of slots is not set, the driver will use
the default value (2), which is set by fsl_esai_probe().

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210402081405.9892-1-shc_work@mail.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm: Fix a5xx/a6xx timestamps

[ Upstream commit 9fbd3088351b92e8c2cef6e37a39decb12a8d5bb ]

They were reading a counter that was configured to ALWAYS_COUNT (ie.
cycles that the GPU is doing something) rather than ALWAYS_ON.  This
isn't the thing that userspace is looking for.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210325012358.1759770-2-robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: omap1: fix building with clang IAS

[ Upstream commit 28399a5a6d569c9bdb612345e4933046ca37cde5 ]

The clang integrated assembler fails to build one file with
a complex asm instruction:

arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: error: invalid instruction, any one of the following would fix this:
 mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
 ^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: armv6t2
 mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
 ^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: thumb2
 mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
 ^

The problem is that 'NR_IRQS_LEGACY' is not defined here. Apparently
gas does not care because we first add and then subtract this number,
leading to the immediate value to be the same regardless of the
specific definition of NR_IRQS_LEGACY.

Neither the way that 'gas' just silently builds this file, nor the
way that clang IAS makes nonsensical suggestions for how to fix it
is great. Fortunately there is an easy fix, which is to #include
the header that contains the definition.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210308153430.2530616-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: keystone: fix integer overflow warning

[ Upstream commit 844b85dda2f569943e1e018fdd63b6f7d1d6f08e ]

clang warns about an impossible condition when building with 32-bit
phys_addr_t:

arch/arm/mach-keystone/keystone.c:79:16: error: result of comparison of constant 51539607551 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
            mem_end   > KEYSTONE_HIGH_PHYS_END) {
            ~~~~~~~   ^ ~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-keystone/keystone.c:78:16: error: result of comparison of constant 34359738368 with expression of type 'phys_addr_t' (aka 'unsigned int') is always true [-Werror,-Wtautological-constant-out-of-range-compare]
        if (mem_start < KEYSTONE_HIGH_PHYS_START ||
            ~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~

Change the temporary variable to a fixed-size u64 to avoid the warning.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Link: https://lore.kernel.org/r/20210323131814.2751750-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

neighbour: Disregard DEAD dst in neigh_update

[ Upstream commit d47ec7a0a7271dda08932d6208e4ab65ab0c987c ]

After a short network outage, the dst_entry is timed out and put
in DST_OBSOLETE_DEAD. We are in this code because arp reply comes
from this neighbour after network recovers. There is a potential
race condition that dst_entry is still in DST_OBSOLETE_DEAD.
With that, another neighbour lookup causes more harm than good.

In best case all packets in arp_queue are lost. This is
counterproductive to the original goal of finding a better path
for those packets.

I observed a worst case with 4.x kernel where a dst_entry in
DST_OBSOLETE_DEAD state is associated with loopback net_device.
It leads to an ethernet header with all zero addresses.
A packet with all zero source MAC address is quite deadly with
mac80211, ath9k and 802.11 block ack.  It fails
ieee80211_find_sta_by_ifaddr in ath9k (xmit.c). Ath9k flushes tx
queue (ath_tx_complete_aggr). BAW (block ack window) is not
updated. BAW logic is damaged and ath9k transmission is disabled.

Signed-off-by: Tong Zhu <zhutong@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpu/xen: Fix a use after free in xen_drm_drv_init

[ Upstream commit 52762efa2b256ed1c5274e5177cbd52ee11a2f6a ]

In function displback_changed, has the call chain
displback_connect(front_info)->xen_drm_drv_init(front_info).
We can see that drm_info is assigned to front_info->drm_info
and drm_info is freed in fail branch in xen_drm_drv_init().

Later displback_disconnect(front_info) is called and it calls
xen_drm_drv_fini(front_info) cause a use after free by
drm_info = front_info->drm_info statement.

My patch has done two things. First fixes the fail label which
drm_info = kzalloc() failed and still free the drm_info.
Second sets front_info->drm_info to NULL to avoid uaf.

Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210323014656.10068-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: max98373: Added 30ms turn on/off time delay

[ Upstream commit 3a27875e91fb9c29de436199d20b33f9413aea77 ]

Amp requires 10 ~ 30ms for the power ON and OFF.
Added 30ms delay for stability.

Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Link: https://lore.kernel.org/r/20210325033555.29377-2-ryans.lee@maximintegrated.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: max98373: Changed amp shutdown register as volatile

[ Upstream commit a23f9099ff1541f15704e96b784d3846d2a4483d ]

0x20FF(amp global enable) register was defined as non-volatile,
but it is not. Overheating, overcurrent can cause amp shutdown
in hardware.
'regmap_write' compare register readback value before writing
to avoid same value writing. 'regmap_read' just read cache
not actual hardware value for the non-volatile register.
When amp is internally shutdown by some reason, next 'AMP ON'
command can be ignored because regmap think amp is already ON.

Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Link: https://lore.kernel.org/r/20210325033555.29377-1-ryans.lee@maximintegrated.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xfrm: BEET mode doesn't support fragments for inner packets

[ Upstream commit 68dc022d04eb0fd60a540e242dcb11ec1bee07e2 ]

BEET mode replaces the IP(6) Headers with new IP(6) Headers when sending
packets. However, when it's a fragment before the replacement, currently
kernel keeps the fragment flag and replace the address field then encaps
it with ESP. It would cause in RX side the fragments to get reassembled
before decapping with ESP, which is incorrect.

In Xiumei's testing, these fragments went over an xfrm interface and got
encapped with ESP in the device driver, and the traffic was broken.

I don't have a good way to fix it, but only to warn this out in dmesg.

Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: Fix softirq/hardirq disabling in iwl_pcie_enqueue_hcmd()

[ Upstream commit 2800aadc18a64c96b051bcb7da8a7df7d505db3f ]

It's possible for iwl_pcie_enqueue_hcmd() to be called with hard IRQs
disabled (e.g. from LED core). We can't enable BHs in such a situation.

Turn the unconditional BH-enable/BH-disable code into
hardirq-disable/conditional-enable.

This fixes the warning below.

 WARNING: CPU: 1 PID: 1139 at kernel/softirq.c:178 __local_bh_enable_ip+0xa5/0xf0
 CPU: 1 PID: 1139 Comm: NetworkManager Not tainted 5.12.0-rc1-00004-gb4ded168af79 #7
 Hardware name: LENOVO 20K5S22R00/20K5S22R00, BIOS R0IET38W (1.16 ) 05/31/2017
 RIP: 0010:__local_bh_enable_ip+0xa5/0xf0
 Code: f7 69 e8 ee 23 14 00 fb 66 0f 1f 44 00 00 65 8b 05 f0 f4 f7 69 85 c0 74 3f 48 83 c4 08 5b c3 65 8b 05 9b fe f7 69 85 c0 75 8e <0f> 0b eb 8a 48 89 3c 24 e8 4e 20 14 00 48 8b 3c 24 eb 91 e8 13 4e
 RSP: 0018:ffffafd580b13298 EFLAGS: 00010046
 RAX: 0000000000000000 RBX: 0000000000000201 RCX: 0000000000000000
 RDX: 0000000000000003 RSI: 0000000000000201 RDI: ffffffffc1272389
 RBP: ffff96517ae4c018 R08: 0000000000000001 R09: 0000000000000000
 R10: ffffafd580b13178 R11: 0000000000000001 R12: ffff96517b060000
 R13: 0000000000000000 R14: ffffffff80000000 R15: 0000000000000001
 FS:  00007fc604ebefc0(0000) GS:ffff965267480000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 000055fb3fef13b2 CR3: 0000000109112004 CR4: 00000000003706e0
 Call Trace:
  ? _raw_spin_unlock_bh+0x1f/0x30
  iwl_pcie_enqueue_hcmd+0x5d9/0xa00 [iwlwifi]
  iwl_trans_txq_send_hcmd+0x6c/0x430 [iwlwifi]
  iwl_trans_send_cmd+0x88/0x170 [iwlwifi]
  ? lock_acquire+0x277/0x3d0
  iwl_mvm_send_cmd+0x32/0x80 [iwlmvm]
  iwl_mvm_led_set+0xc2/0xe0 [iwlmvm]
  ? led_trigger_event+0x46/0x70
  led_trigger_event+0x46/0x70
  ieee80211_do_open+0x5c5/0xa20 [mac80211]
  ieee80211_open+0x67/0x90 [mac80211]
  __dev_open+0xd4/0x150
  __dev_change_flags+0x19e/0x1f0
  dev_change_flags+0x23/0x60
  do_setlink+0x30d/0x1230
  ? lock_is_held_type+0xb4/0x120
  ? __nla_validate_parse.part.7+0x57/0xcb0
  ? __lock_acquire+0x2e1/0x1a50
  __rtnl_newlink+0x560/0x910
  ? __lock_acquire+0x2e1/0x1a50
  ? __lock_acquire+0x2e1/0x1a50
  ? lock_acquire+0x277/0x3d0
  ? sock_def_readable+0x5/0x290
  ? lock_is_held_type+0xb4/0x120
  ? find_held_lock+0x2d/0x90
  ? sock_def_readable+0xb3/0x290
  ? lock_release+0x166/0x2a0
  ? lock_is_held_type+0x90/0x120
  rtnl_newlink+0x47/0x70
  rtnetlink_rcv_msg+0x25c/0x470
  ? netlink_deliver_tap+0x97/0x3e0
  ? validate_linkmsg+0x350/0x350
  netlink_rcv_skb+0x50/0x100
  netlink_unicast+0x1b2/0x280
  netlink_sendmsg+0x336/0x450
  sock_sendmsg+0x5b/0x60
  ____sys_sendmsg+0x1ed/0x250
  ? copy_msghdr_from_user+0x5c/0x90
  ___sys_sendmsg+0x88/0xd0
  ? lock_is_held_type+0xb4/0x120
  ? find_held_lock+0x2d/0x90
  ? lock_release+0x166/0x2a0
  ? __fget_files+0xfe/0x1d0
  ? __sys_sendmsg+0x5e/0xa0
  __sys_sendmsg+0x5e/0xa0
  ? lockdep_hardirqs_on_prepare+0xd9/0x170
  do_syscall_64+0x33/0x80
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7fc605c9572d
 Code: 28 89 54 24 1c 48 89 74 24 10 89 7c 24 08 e8 da ee ff ff 8b 54 24 1c 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 33 44 89 c7 48 89 44 24 08 e8 2e ef ff ff 48
 RSP: 002b:00007fffc83789f0 EFLAGS: 00000293 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 000055ef468570c0 RCX: 00007fc605c9572d
 RDX: 0000000000000000 RSI: 00007fffc8378a30 RDI: 000000000000000c
 RBP: 0000000000000010 R08: 0000000000000000 R09: 0000000000000000
 R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000000
 R13: 00007fffc8378b80 R14: 00007fffc8378b7c R15: 0000000000000000
 irq event stamp: 170785
 hardirqs last  enabled at (170783): [<ffffffff9609a8c2>] __local_bh_enable_ip+0x82/0xf0
 hardirqs last disabled at (170784): [<ffffffff96a8613d>] _raw_read_lock_irqsave+0x8d/0x90
 softirqs last  enabled at (170782): [<ffffffffc1272389>] iwl_pcie_enqueue_hcmd+0x5d9/0xa00 [iwlwifi]
 softirqs last disabled at (170785): [<ffffffffc1271ec6>] iwl_pcie_enqueue_hcmd+0x116/0xa00 [iwlwifi]

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM/Clang v12.0.0-rc3
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2103021125430.12405@cbobk.fhfr.pm
Signed-off-by: Sasha Levin <sashal@kernel.org>

arc: kernel: Return -EFAULT if copy_to_user() fails

[ Upstream commit 46e152186cd89d940b26726fff11eb3f4935b45a ]

The copy_to_user() function returns the number of bytes remaining to be
copied, but we want to return -EFAULT if the copy doesn't complete.

Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

lockdep: Add a missing initialization hint to the "INFO: Trying to register non-static key" message

[ Upstream commit 3a85969e9d912d5dd85362ee37b5f81266e00e77 ]

Since this message is printed when dynamically allocated spinlocks (e.g.
kzalloc()) are used without initialization (e.g. spin_lock_init()),
suggest to developers to check whether initialization functions for objects
were called, before making developers wonder what annotation is missing.

[ mingo: Minor tweaks to the message. ]

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210321064913.4619-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: Fix moving mmc devices with aliases for omap4 & 5

[ Upstream commit 77335a040178a0456d4eabc8bf17a7ca3ee4a327 ]

Fix moving mmc devices with dts aliases as discussed on the lists.
Without this we now have internal eMMC mmc1 show up as mmc2 compared
to the earlier order of devices.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: Drop duplicate sha2md5_fck to fix clk_disable race

[ Upstream commit 140a776833957539c84301dbdb4c3013876de118 ]

We have a duplicate legacy clock defined for sha2md5_fck that can
sometimes race with clk_disable() with the dts configured clock
for OMAP4_SHA2MD5_CLKCTRL when unused clocks are disabled during
boot causing an "Unhandled fault: imprecise external abort".

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: x86: Call acpi_boot_table_init() after acpi_table_upgrade()

[ Upstream commit 6998a8800d73116187aad542391ce3b2dd0f9e30 ]

Commit 1a1c130ab757 ("ACPI: tables: x86: Reserve memory occupied by
ACPI tables") attempted to address an issue with reserving the memory
occupied by ACPI tables, but it broke the initrd-based table override
mechanism relied on by multiple users.

To restore the initrd-based ACPI table override functionality, move
the acpi_boot_table_init() invocation in setup_arch() on x86 after
the acpi_table_upgrade() one.

Fixes: 1a1c130ab757 ("ACPI: tables: x86: Reserve memory occupied by ACPI tables")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: fix wq cleanup of WQCFG registers

[ Upstream commit ea9aadc06a9f10ad20a90edc0a484f1147d88a7a ]

A pre-release silicon erratum workaround where wq reset does not clear
WQCFG registers was leaked into upstream code. Use wq reset command
instead of blasting the MMIO region. This also address an issue where
we clobber registers in future devices.

Fixes: da32b28c95a7 ("dmaengine: idxd: cleanup workqueue config after disabling")
Reported-by: Shreenivaas Devarajan <shreenivaas.devarajan@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161824330020.881560.16375921906426627033.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: plx_dma: add a missing put_device() on error path

[ Upstream commit 07503e6aefe4a6efd777062191944a14f03b3a18 ]

Add a missing put_device(&pdev->dev) if the call to
dma_async_device_register(dma); fails.

Fixes: 905ca51e63be ("dmaengine: plx-dma: Introduce PLX DMA engine PCI driver skeleton")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/YFnq/0IQzixtAbC1@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: Fix a double free in dma_async_device_register

[ Upstream commit ea45b6008f8095db0cc09ad6e03c7785c2986197 ]

In the first list_for_each_entry() macro of dma_async_device_register,
it gets the chan from list and calls __dma_async_device_channel_register
(..,chan). We can see that chan->local is allocated by alloc_percpu() and
it is freed chan->local by free_percpu(chan->local) when
__dma_async_device_channel_register() failed.

But after __dma_async_device_channel_register() failed, the caller will
goto err_out and freed the chan->local in the second time by free_percpu().

The cause of this problem is forget to set chan->local to NULL when
chan->local was freed in __dma_async_device_channel_register(). My
patch sets chan->local to NULL when the callee failed to avoid double free.

Fixes: d2fb0a0438384 ("dmaengine: break out channel registration")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20210331014458.3944-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: dw: Make it dependent to HAS_IOMEM

[ Upstream commit 88cd1d6191b13689094310c2405394e4ce36d061 ]

Some architectures do not provide devm_*() APIs. Hence make the driver
dependent on HAVE_IOMEM.

Fixes: dbde5c2934d1 ("dw_dmac: use devm_* functions to simplify code")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210324141757.24710-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: fix wq size store permission state

[ Upstream commit 0fff71c5a311e1264988179f7dcc217fda15fadd ]

WQ size can only be changed when the device is disabled. Current code
allows change when device is enabled but wq is disabled. Change the check
to detect device state.

Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161782558755.107710.18138252584838406025.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: fix opcap sysfs attribute output

[ Upstream commit ea6a5735d2a61b938a302eb3629272342a9e7c46 ]

The operation capability register is 256bits. The current output only
prints out the first 64bits. Fix to output the entire 256bits. The current
code omits operation caps from IAX devices.

Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Reported-by: Lucas Van <lucas.van@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161645624963.2003736.829798666998490151.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: fix delta_rec and crc size field for completion record

[ Upstream commit 4ac823e9cd85f66da274c951d21bf9f6b714b729 ]

The delta_rec_size and crc_val in the completion record should
be 32bits and not 16bits.

Fixes: bfe1d56091c1 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Reported-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161645618572.2003490.14466173451736323035.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: Fix clobbering of SWERR overflow bit on writeback

[ Upstream commit ea941ac294d75d0ace50797aebf0056f6f8f7a7f ]

Current code blindly writes over the SWERR and the OVERFLOW bits. Write
back the bits actually read instead so the driver avoids clobbering the
OVERFLOW bit that comes after the register is read.

Fixes: bfe1d56091c1 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Reported-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161352082229.3511254.1002151220537623503.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: sysfs: Obey valid_mask

[ Upstream commit 23cf00ddd2e1aacf1873e43f5e0c519c120daf7a ]

Do not allow exporting GPIOs which are set invalid
by the driver's valid mask.

Fixes: 726cb3ba4969 ("gpiolib: Support 'gpio-reserved-ranges' property")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: nspire-keypad - enable interrupts only when opened

[ Upstream commit 69d5ff3e9e51e23d5d81bf48480aa5671be67a71 ]

The driver registers an interrupt handler in _probe, but didn't configure
them until later when the _open function is called. In between, the keypad
can fire an IRQ due to touchpad activity, which the handler ignores. This
causes the kernel to disable the interrupt, blocking the keypad from
working.

Fix this by disabling interrupts before registering the handler.
Additionally, disable them in _close, so that they're only enabled while
open.

Fixes: fc4f31461892 ("Input: add TI-Nspire keypad support")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/3383725.iizBOSrK1V@linux-e202.suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mtd: rawnand: mtk: Fix WAITRDY break condition and timeout

[ Upstream commit 2fb164f0ce95e504e2688b4f984893c29ebd19ab ]

This fixes NAND_OP_WAITRDY_INSTR operation in the driver. Without this
change the driver waits till the system is busy, but we should wait till
the busy flag is cleared. The readl_poll_timeout() function gets a break
condition, not a wait condition.

In addition fix the timeout. The timeout_ms is given in ms, but the
readl_poll_timeout() function takes the timeout in us. Multiple the
given timeout by 1000 to convert it.

Without this change, the driver does not work at all, it doesn't even
identify the NAND chip.

Fixes: 5197360f9e09 ("mtd: rawnand: mtk: Convert the driver to exec_op()")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210309000107.1368404-1-hauke@hauke-m.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sctp: fix race condition in sctp_destroy_sock

commit b166a20b07382b8bc1dcee2a448715c9c2c81b5b upstream.

If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.

This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
   attached to BPF_CGROUP_INET_SOCK_CREATE which denies
   creation of the sctp socket.

The bug is fixed by acquiring addr_wq_lock in sctp_destroy_sock
instead of sctp_close.

This addresses CVE-2021-23133.

Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Fixes: 610236587600 ("bpf: Add new cgroup attach type to enable sock modifications")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.10.31

Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Andrei Rabusov <a.rabusov@tum.de>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Jason Self <jason@bluehome.net>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210415144413.165663182@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/events: fix setting irq affinity

The backport of upstream patch 25da4618af240fbec61 ("xen/events: don't
unmask an event channel when an eoi is pending") introduced a
regression for stable kernels 5.10 and older: setting IRQ affinity for
IRQs related to interdomain events would no longer work, as moving the
IRQ to its new cpu was not included in the irq_ack callback for those
events.

Fix that by adding the needed call.

Note that kernels 5.11 and later don't need the explicit moving of the
IRQ to the target cpu in the irq_ack callback, due to a rework of the
affinity setting in kernel 5.11.

Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sfp: cope with SFPs that set both LOS normal and LOS inverted

commit 624407d2cf14ff58e53bf4b2af9595c4f21d606e upstream.

The SFP MSA defines two option bits in byte 65 to indicate how the
Rx_LOS signal on SFP pin 8 behaves:

bit 2 - Loss of Signal implemented, signal inverted from standard
        definition in SFP MSA (often called "Signal Detect").
bit 1 - Loss of Signal implemented, signal as defined in SFP MSA
        (often called "Rx_LOS").

Clearly, setting both bits results in a meaningless situation: it would
mean that LOS is implemented in both the normal sense (1 = signal loss)
and inverted sense (0 = signal loss).

Unfortunately, there are modules out there which set both bits, which
will be initially interpret as "inverted" sense, and then, if the LOS
signal changes state, we will toggle between LINK_UP and WAIT_LOS
states.

Change our LOS handling to give well defined behaviour: only interpret
these bits as meaningful if exactly one is set, otherwise treat it as
if LOS is not implemented.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyYQa-0004iR-CU@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sfp: relax bitrate-derived mode check

commit 7a77233ec6d114322e2c4f71b4e26dbecd9ea8a7 upstream.

Do not check the encoding when deriving 1000BASE-X from the bitrate
when no other modes are discovered. Some GPON modules (VSOL V2801F
and CarlitoxxPro CPGOS03-0490 v2.0) indicate NRZ encoding with a
1200Mbaud bitrate, but should be driven with 1000BASE-X on the host
side.

Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf map: Tighten snprintf() string precision to pass gcc check on some 32-bit arches

commit 77d02bd00cea9f1a87afe58113fa75b983d6c23a upstream.

Noticed on a debian:experimental mips and mipsel cross build build
environment:

  perfbuilder@ec265a086e9b:~$ mips-linux-gnu-gcc --version | head -1
  mips-linux-gnu-gcc (Debian 10.2.1-3) 10.2.1 20201224
  perfbuilder@ec265a086e9b:~$

    CC       /tmp/build/perf/util/map.o
  util/map.c: In function 'map__new':
  util/map.c:109:5: error: '%s' directive output may be truncated writing between 1 and 2147483645 bytes into a region of size 4096 [-Werror=format-truncation=]
    109 |    "%s/platforms/%s/arch-%s/usr/lib/%s",
        |     ^~
  In file included from /usr/mips-linux-gnu/include/stdio.h:867,
                   from util/symbol.h:11,
                   from util/map.c:2:
  /usr/mips-linux-gnu/include/bits/stdio2.h:67:10: note: '__builtin___snprintf_chk' output 32 or more bytes (assuming 4294967321) into a destination of size 4096
     67 |   return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
        |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     68 |        __bos (__s), __fmt, __va_arg_pack ());
        |        ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  cc1: all warnings being treated as errors

Since we have the lenghts for what lands in that place, use it to give
the compiler more info and make it happy.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: x_tables: fix compat match/target pad out-of-bound write

commit b29c457a6511435960115c0f548c4360d5f4801d upstream.

xt_compat_match/target_from_user doesn't check that zeroing the area
to start of next rule won't write past end of allocated ruleset blob.

Remove this code and zero the entire blob beforehand.

Reported-by: syzbot+cfc0247ac173f597aaaa@syzkaller.appspotmail.com
Reported-by: Andy Nguyen <theflow@google.com>
Fixes: 9fa492cdc160c ("[NETFILTER]: x_tables: simplify compat API")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: don't ignore REQ_NOWAIT for direct IO

[ Upstream commit f8b78caf21d5bc3fcfc40c18898f9d52ed1451a5 ]

If IOCB_NOWAIT is set on submission, then that needs to get propagated to
REQ_NOWAIT on the block side. Otherwise we completely lose this
information, and any issuer of IOCB_NOWAIT IO will potentially end up
blocking on eg request allocation on the storage side.

Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

riscv,entry: fix misaligned base for excp_vect_table

[ Upstream commit ac8d0b901f0033b783156ab2dc1a0e73ec42409b ]

In RV64, the size of each entry in excp_vect_table is 8 bytes. If the
base of the table is not 8-byte aligned, loading an entry in the table
will raise a misaligned exception. Although such exception will be
handled by opensbi/bbl, this still causes performance degradation.

Signed-off-by: Zihao Yu <yuzihao@ict.ac.cn>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring: don't mark S_ISBLK async work as unbounded

[ Upstream commit 4b982bd0f383db9132e892c0c5144117359a6289 ]

S_ISBLK is marked as unbounded work for async preparation, because it
doesn't match S_ISREG. That is incorrect, as any read/write to a block
device is also a bounded operation. Fix it up and ensure that S_ISBLK
isn't marked unbounded.

Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

null_blk: fix command timeout completion handling

[ Upstream commit de3510e52b0a398261271455562458003b8eea62 ]

Memory backed or zoned null block devices may generate actual request
timeout errors due to the submission path being blocked on memory
allocation or zone locking. Unlike fake timeouts or injected timeouts,
the request submission path will call blk_mq_complete_request() or
blk_mq_end_request() for these real timeout errors, causing a double
completion and use after free situation as the block layer timeout
handler executes blk_mq_rq_timed_out() and __blk_mq_free_request() in
blk_mq_check_expired(). This problem often triggers a NULL pointer
dereference such as:

BUG: kernel NULL pointer dereference, address: 0000000000000050
RIP: 0010:blk_mq_sched_mark_restart_hctx+0x5/0x20
...
Call Trace:
  dd_finish_request+0x56/0x80
  blk_mq_free_request+0x37/0x130
  null_handle_cmd+0xbf/0x250 [null_blk]
  ? null_queue_rq+0x67/0xd0 [null_blk]
  blk_mq_dispatch_rq_list+0x122/0x850
  __blk_mq_do_dispatch_sched+0xbb/0x2c0
  __blk_mq_sched_dispatch_requests+0x13d/0x190
  blk_mq_sched_dispatch_requests+0x30/0x60
  __blk_mq_run_hw_queue+0x49/0x90
  process_one_work+0x26c/0x580
  worker_thread+0x55/0x3c0
  ? process_one_work+0x580/0x580
  kthread+0x134/0x150
  ? kthread_create_worker_on_cpu+0x70/0x70
  ret_from_fork+0x1f/0x30

This problem very often triggers when running the full btrfs xfstests
on a memory-backed zoned null block device in a VM with limited amount
of memory.

Avoid this by executing blk_mq_complete_request() in null_timeout_rq()
only for commands that are marked for a fake timeout completion using
the fake_timeout boolean in struct null_cmd. For timeout errors injected
through debugfs, the timeout handler will execute
blk_mq_complete_request()i as before. This is safe as the submission
path does not execute complete requests in this case.

In null_timeout_rq(), also make sure to set the command error field to
BLK_STS_TIMEOUT and to propagate this error through to the request
completion.

Reported-by: Johannes Thumshirn <Johannes.Thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Johannes Thumshirn <Johannes.Thumshirn@wdc.com>
Reviewed-by: Johannes Thumshirn <Johannes.Thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210331225244.126426-1-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

idr test suite: Create anchor before launching throbber

[ Upstream commit 094ffbd1d8eaa27ed426feb8530cb1456348b018 ]

The throbber could race with creation of the anchor entry and cause the
IDR to have zero entries in it, which would cause the test to fail.

Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

idr test suite: Take RCU read lock in idr_find_test_1

[ Upstream commit 703586410da69eb40062e64d413ca33bd735917a ]

When run on a single CPU, this test would frequently access already-freed
memory.  Due to timing, this bug never showed up on multi-CPU tests.

Reported-by: Chris von Recklinghausen <crecklin@redhat.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

radix tree test suite: Register the main thread with the RCU library

[ Upstream commit 1bb4bd266cf39fd2fa711f2d265c558b92df1119 ]

Several test runners register individual worker threads with the
RCU library, but neglect to register the main thread, which can lead
to objects being freed while the main thread is in what appears to be
an RCU critical section.

Reported-by: Chris von Recklinghausen <crecklin@redhat.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

block: only update parent bi_status when bio fail

[ Upstream commit 3edf5346e4f2ce2fa0c94651a90a8dda169565ee ]

For multiple split bios, if one of the bio is fail, the whole
should return error to application. But we found there is a race
between bio_integrity_verify_fn and bio complete, which return
io success to application after one of the bio fail. The race as
following:

split bio(READ)          kworker

nvme_complete_rq
blk_update_request //split error=0
  bio_endio
    bio_integrity_endio
      queue_work(kintegrityd_wq, &bip->bip_work);

                         bio_integrity_verify_fn
                         bio_endio //split bio
                          __bio_chain_endio
                             if (!parent->bi_status)

                               <interrupt entry>
                               nvme_irq
                                 blk_update_request //parent error=7
                                 req_bio_endio
                                    bio->bi_status = 7 //parent bio
                               <interrupt exit>

                               parent->bi_status = 0
                        parent->bi_end_io() // return bi_status=0

The bio has been split as two: split and parent. When split
bio completed, it depends on kworker to do endio, while
bio_integrity_verify_fn have been interrupted by parent bio
complete irq handler. Then, parent bio->bi_status which have
been set in irq handler will overwrite by kworker.

In fact, even without the above race, we also need to conside
the concurrency beteen mulitple split bio complete and update
the same parent bi_status. Normally, multiple split bios will
be issued to the same hctx and complete from the same irq
vector. But if we have updated queue map between multiple split
bios, these bios may complete on different hw queue and different
irq vector. Then the concurrency update parent bi_status may
cause the final status error.

Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210331115359.1125679-1-yuyufen@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

XArray: Fix splitting to non-zero orders

[ Upstream commit 3012110d71f41410932924e1d188f9eb57f1f824 ]

Splitting an order-4 entry into order-2 entries would leave the array
containing pointers to 000040008000c000 instead of 000044448888cccc.
This is a one-character fix, but enhance the test suite to check this
case.

Reported-by: Zi Yan <ziy@nvidia.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpu: host1x: Use different lock classes for each client

[ Upstream commit a24f98176d1efae2c37d3438c57a624d530d9c33 ]

To avoid false lockdep warnings, give each client lock a different
lock class, passed from the initialization site by macro.

Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/tegra: dc: Don't set PLL clock to 0Hz

[ Upstream commit f8fb97c915954fc6de6513cdf277103b5c6df7b3 ]

RGB output doesn't allow to change parent clock rate of the display and
PCLK rate is set to 0Hz in this case. The tegra_dc_commit_state() shall
not set the display clock to 0Hz since this change propagates to the
parent clock. The DISP clock is defined as a NODIV clock by the tegra-clk
driver and all NODIV clocks use the CLK_SET_RATE_PARENT flag.

This bug stayed unnoticed because by default PLLP is used as the parent
clock for the display controller and PLLP silently skips the erroneous 0Hz
rate changes because it always has active child clocks that don't permit
rate changes. The PLLP isn't acceptable for some devices that we want to
upstream (like Samsung Galaxy Tab and ASUS TF700T) due to a display panel
clock rate requirements that can't be fulfilled by using PLLP and then the
bug pops up in this case since parent clock is set to 0Hz, killing the
display output.

Don't touch DC clock if pclk=0 in order to fix the problem.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tools/kvm_stat: Add restart delay

[ Upstream commit 75f94ecbd0dfd2ac4e671f165f5ae864b7301422 ]

If this service is enabled and the system rebooted, Systemd's initial
attempt to start this unit file may fail in case the kvm module is not
loaded. Since we did not specify a delay for the retries, Systemd
restarts with a minimum delay a number of times before giving up and
disabling the service. Which means a subsequent kvm module load will
have kvm running without monitoring.
Adding a delay to fix this.

Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Message-Id: <20210325122949.1433271-1-raspl@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ftrace: Check if pages were allocated before calling free_pages()

[ Upstream commit 59300b36f85f254260c81d9dd09195fa49eb0f98 ]

It is possible that on error pg->size can be zero when getting its order,
which would return a -1 value. It is dangerous to pass in an order of -1
to free_pages(). Check if order is greater than or equal to zero before
calling free_pages().

Link: https://lore.kernel.org/lkml/20210330093916.432697c7@gandalf.local.home/
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: report "already frozen/thawed" errors

[ Upstream commit ff132c5f93c06bd4432bbab5c369e468653bdec4 ]

Before this patch, gfs2's freeze function failed to report an error
when the target file system was already frozen as it should (and as
generic vfs function freeze_super does. Similarly, gfs2's thaw function
failed to report an error when trying to thaw a file system that is not
frozen, as vfs function thaw_super does. The errors were checked, but
it always returned a 0 return code.

This patch adds the missing error return codes to gfs2 freeze and thaw.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/imx: imx-ldb: fix out of bounds array access warning

[ Upstream commit 33ce7f2f95cabb5834cf0906308a5cb6103976da ]

When CONFIG_OF is disabled, building with 'make W=1' produces warnings
about out of bounds array access:

drivers/gpu/drm/imx/imx-ldb.c: In function 'imx_ldb_set_clock.constprop':
drivers/gpu/drm/imx/imx-ldb.c:186:8: error: array subscript -22 is below array bounds of 'struct clk *[4]' [-Werror=array-bounds]

Add an error check before the index is used, which helps with the
warning, as well as any possible other error condition that may be
triggered at runtime.

The warning could be fixed by adding a Kconfig depedency on CONFIG_OF,
but Liu Ying points out that the driver may hit the out-of-bounds
problem at runtime anyway.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Disable guest access to trace filter controls

[ Upstream commit a354a64d91eec3e0f8ef0eed575b480fd75b999c ]

Disable guest access to the Trace Filter control registers.
We do not advertise the Trace filter feature to the guest
(ID_AA64DFR0_EL1: TRACE_FILT is cleared) already, but the guest
can still access the TRFCR_EL1 unless we trap it.

This will also make sure that the guest cannot fiddle with
the filtering controls set by a nvhe host.

Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323120647.454211-3-suzuki.poulose@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Hide system instruction access to Trace registers

[ Upstream commit 1d676673d665fd2162e7e466dcfbe5373bfdb73e ]

Currently we advertise the ID_AA6DFR0_EL1.TRACEVER for the guest,
when the trace register accesses are trapped (CPTR_EL2.TTA == 1).
So, the guest will get an undefined instruction, if trusts the
ID registers and access one of the trace registers.
Lets be nice to the guest and hide the feature to avoid
unexpected behavior.

Even though this can be done at KVM sysreg emulation layer,
we do this by removing the TRACEVER from the sanitised feature
register field. This is fine as long as the ETM drivers
can handle the individual trace units separately, even
when there are differences among the CPUs.

Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323120647.454211-2-suzuki.poulose@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: Flag a withdraw if init_threads() fails

[ Upstream commit 62dd0f98a0e5668424270b47a0c2e973795faba7 ]

Interrupting mount with ^C quickly enough can cause the kthread_run()
calls in gfs2's init_threads() to fail and the error path leads to a
deadlock on the s_umount rwsem. The abridged chain of events is:

  [mount path]
  get_tree_bdev()
    sget_fc()
      alloc_super()
        down_write_nested(&s->s_umount, SINGLE_DEPTH_NESTING); [acquired]
    gfs2_fill_super()
      gfs2_make_fs_rw()
        init_threads()
          kthread_run()
            ( Interrupted )
      [Error path]
      gfs2_gl_hash_clear()
        flush_workqueue(glock_workqueue)
          wait_for_completion()

  [workqueue context]
  glock_work_func()
    run_queue()
      do_xmote()
        freeze_go_sync()
          freeze_super()
            down_write(&sb->s_umount) [deadlock]

In freeze_go_sync() there is a gfs2_withdrawn() check that we can use to
make sure freeze_super() is not called in the error path, so add a
gfs2_withdraw_delayed() call when init_threads() fails.

Ref: https://bugzilla.kernel.org/show_bug.cgi?id=212231

Reported-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

interconnect: core: fix error return code of icc_link_destroy()

[ Upstream commit 715ea61532e731c62392221238906704e63d75b6 ]

When krealloc() fails and new is NULL, no error return code of
icc_link_destroy() is assigned.
To fix this bug, ret is assigned with -ENOMEM hen new is NULL.

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210306132857.17020-1-baijiaju1990@gmail.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 5.10.30

Tested-by: Andrei Rabusov <a.rabusov@tum.de>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Patrick McCormick <pmccormick@digitalocean.com>
Tested-by: Jason Self <jason@bluehome.net>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Hulk Robot <hulkrobot@huawei.com>
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Link: https://lore.kernel.org/r/20210412084013.643370347@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "net: sched: bump refcount for new action in ACT replace mode"

commit 4ba86128ba077fbb7d86516ae24ed642e6c3adef upstream.

This reverts commit 6855e8213e06efcaf7c02a15e12b1ae64b9a7149.

Following commit in series fixes the issue without introducing regression
in error rollback of tcf_action_destroy().

Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: stop dump llsec params for monitors

commit 1534efc7bbc1121e92c86c2dabebaf2c9dcece19 upstream.

This patch stops dumping llsec params for monitors which we don't support
yet. Otherwise we will access llsec mib which isn't initialized for
monitors.

Reported-by: syzbot+cde43a581a8e5f317bc2@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-16-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: forbid monitor for del llsec seclevel

commit 9dde130937e95b72adfae64ab21d6e7e707e2dac upstream.

This patch forbids to del llsec seclevel for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.

Reported-by: syzbot+fbf4fc11a819824e027b@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-15-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: forbid monitor for set llsec params

commit 88c17855ac4291fb462e13a86b7516773b6c932e upstream.

This patch forbids to set llsec params for monitor interfaces which we
don't support yet.

Reported-by: syzbot+8b6719da8a04beeafcc3@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210405003054.256017-3-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: fix nl802154 del llsec devkey

commit 27c746869e1a135dffc2f2a80715bb7aa00445b4 upstream.

This patch fixes a nullpointer dereference if NL802154_ATTR_SEC_DEVKEY is
not set by the user. If this is the case nl802154 will return -EINVAL.

Reported-by: syzbot+368672e0da240db53b5f@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210221174321.14210-4-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: fix nl802154 add llsec key

commit 20d5fe2d7103f5c43ad11a3d6d259e9d61165c35 upstream.

This patch fixes a nullpointer dereference if NL802154_ATTR_SEC_KEY is
not set by the user. If this is the case nl802154 will return -EINVAL.

Reported-by: syzbot+ce4e062c2d51977ddc50@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210221174321.14210-3-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: fix nl802154 del llsec dev

commit 3d1eac2f45585690d942cf47fd7fbd04093ebd1b upstream.

This patch fixes a nullpointer dereference if NL802154_ATTR_SEC_DEVICE is
not set by the user. If this is the case nl802154 will return -EINVAL.

Reported-by: syzbot+d946223c2e751d136c94@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210221174321.14210-2-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: fix nl802154 del llsec key

commit 37feaaf5ceb2245e474369312bb7b922ce7bce69 upstream.

This patch fixes a nullpointer dereference if NL802154_ATTR_SEC_KEY is
not set by the user. If this is the case nl802154 will return -EINVAL.

Reported-by: syzbot+ac5c11d2959a8b3c4806@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210221174321.14210-1-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: nl-mac: fix check on panid

commit 6f7f657f24405f426212c09260bf7fe8a52cef33 upstream.

This patch fixes a null pointer derefence for panid handle by move the
check for the netlink variable directly before accessing them.

Reported-by: syzbot+d4c07de0144f6f63be3a@syzkaller.appspotmail.com
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210228151817.95700-4-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mac802154: Fix general protection fault

commit 1165affd484889d4986cf3b724318935a0b120d8 upstream.

syzbot found general protection fault in crypto_destroy_tfm()[1].
It was caused by wrong clean up loop in llsec_key_alloc().
If one of the tfm array members is in IS_ERR() range it will
cause general protection fault in clean up function [1].

Call Trace:
 crypto_free_aead include/crypto/aead.h:191 [inline] [1]
 llsec_key_alloc net/mac802154/llsec.c:156 [inline]
 mac802154_llsec_key_add+0x9e0/0xcc0 net/mac802154/llsec.c:249
 ieee802154_add_llsec_key+0x56/0x80 net/mac802154/cfg.c:338
 rdev_add_llsec_key net/ieee802154/rdev-ops.h:260 [inline]
 nl802154_add_llsec_key+0x3d3/0x560 net/ieee802154/nl802154.c:1584
 genl_family_rcv_msg_doit+0x228/0x320 net/netlink/genetlink.c:739
 genl_family_rcv_msg net/netlink/genetlink.c:783 [inline]
 genl_rcv_msg+0x328/0x580 net/netlink/genetlink.c:800
 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
 genl_rcv+0x24/0x40 net/netlink/genetlink.c:811
 netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
 netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
 netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:674
 ____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
 ___sys_sendmsg+0xf3/0x170 net/socket.c:2404
 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
 do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
 entry_SYSCALL_64_after_hwframe+0x44/0xae

Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reported-by: syzbot+9ec037722d2603a9f52e@syzkaller.appspotmail.com
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20210304152125.1052825-1-paskripkin@gmail.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: net: fix memory leak in peak_usb_create_dev

commit a0b96b4a62745397aee662670cfc2157bac03f55 upstream.

syzbot reported memory leak in peak_usb.
The problem was in case of failure after calling
->dev_init()[2] in peak_usb_create_dev()[1]. The data
allocated int dev_init() wasn't freed, so simple
->dev_free() call fix this problem.

backtrace:
    [<0000000079d6542a>] kmalloc include/linux/slab.h:552 [inline]
    [<0000000079d6542a>] kzalloc include/linux/slab.h:682 [inline]
    [<0000000079d6542a>] pcan_usb_fd_init+0x156/0x210 drivers/net/can/usb/peak_usb/pcan_usb_fd.c:868   [2]
    [<00000000c09f9057>] peak_usb_create_dev drivers/net/can/usb/peak_usb/pcan_usb_core.c:851 [inline] [1]
    [<00000000c09f9057>] peak_usb_probe+0x389/0x490 drivers/net/can/usb/peak_usb/pcan_usb_core.c:949

Reported-by: syzbot+91adee8d9ebb9193d22d@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: net: fix memory leak in atusb_probe

commit 6b9fbe16955152626557ec6f439f3407b7769941 upstream.

syzbot reported memory leak in atusb_probe()[1].
The problem was in atusb_alloc_urbs().
Since urb is anchored, we need to release the reference
to correctly free the urb

backtrace:
    [<ffffffff82ba0466>] kmalloc include/linux/slab.h:559 [inline]
    [<ffffffff82ba0466>] usb_alloc_urb+0x66/0xe0 drivers/usb/core/urb.c:74
    [<ffffffff82ad3888>] atusb_alloc_urbs drivers/net/ieee802154/atusb.c:362 [inline][2]
    [<ffffffff82ad3888>] atusb_probe+0x158/0x820 drivers/net/ieee802154/atusb.c:1038 [1]

Reported-by: syzbot+28a246747e0a465127f3@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: tun: set tun->dev->addr_len during TUNSETLINK processing

commit cca8ea3b05c972ffb5295367e6c544369b45fbdd upstream.

When changing type with TUNSETLINK ioctl command, set tun->dev->addr_len
to match the appropriate type, using new tun_get_addr_len utility function
which returns appropriate address length for given type. Fixes a
KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=0766d38c656abeace60621896d705743aeefed51

Reported-by: syzbot+001516d86dbe88862cec@syzkaller.appspotmail.com
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: remove WARN_ON() in cfg80211_sme_connect

commit 1b5ab825d9acc0f27d2f25c6252f3526832a9626 upstream.

A WARN_ON(wdev->conn) would trigger in cfg80211_sme_connect(), if multiple
send_msg(NL80211_CMD_CONNECT) system calls are made from the userland, which
should be anticipated and handled by the wireless driver. Remove this WARN_ON()
to prevent kernel panic if kernel is configured to "panic_on_warn".

Bug reported by syzbot.

Reported-by: syzbot+5f9392825de654244975@syzkaller.appspotmail.com
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210407162756.6101-1-ducheng2@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpiolib: Read "gpio-line-names" from a firmware node

commit b41ba2ec54a70908067034f139aa23d0dd2985ce upstream.

On STM32MP1, the GPIO banks are subnodes of pin-controller@50002000,
see arch/arm/boot/dts/stm32mp151.dtsi. The driver for
pin-controller@50002000 is in drivers/pinctrl/stm32/pinctrl-stm32.c
and iterates over all of its DT subnodes when registering each GPIO
bank gpiochip. Each gpiochip has:

  - gpio_chip.parent = dev,
    where dev is the device node of the pin controller
  - gpio_chip.of_node = np,
    which is the OF node of the GPIO bank

Therefore, dev_fwnode(chip->parent) != of_fwnode_handle(chip.of_node),
i.e. pin-controller@50002000 != pin-controller@50002000/gpio@5000*000.

The original code behaved correctly, as it extracted the "gpio-line-names"
from of_fwnode_handle(chip.of_node) = pin-controller@50002000/gpio@5000*000.

To achieve the same behaviour, read property from the firmware node.

Fixes: 7cba1a4d5e162 ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Reported-by: Marek Vasut <marex@denx.de>
Reported-by: Roman Guskov <rguskov@dh-electronics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sched: bump refcount for new action in ACT replace mode

commit 6855e8213e06efcaf7c02a15e12b1ae64b9a7149 upstream.

Currently, action creation using ACT API in replace mode is buggy.
When invoking for non-existent action index 42,

tc action replace action bpf obj foo.o sec <xyz> index 42

kernel creates the action, fills up the netlink response, and then just
deletes the action after notifying userspace.

tc action show action bpf

doesn't list the action.

This happens due to the following sequence when ovr = 1 (replace mode)
is enabled:

tcf_idr_check_alloc is used to atomically check and either obtain
reference for existing action at index, or reserve the index slot using
a dummy entry (ERR_PTR(-EBUSY)).

This is necessary as pointers to these actions will be held after
dropping the idrinfo lock, so bumping the reference count is necessary
as we need to insert the actions, and notify userspace by dumping their
attributes. Finally, we drop the reference we took using the
tcf_action_put_many call in tcf_action_add. However, for the case where
a new action is created due to free index, its refcount remains one.
This when paired with the put_many call leads to the kernel setting up
the action, notifying userspace of its creation, and then tearing it
down. For existing actions, the refcount is still held so they remain
unaffected.

Fortunately due to rtnl_lock serialization requirement, such an action
with refcount == 1 will not be concurrently deleted by anything else, at
best CLS API can move its refcount up and down by binding to it after it
has been published from tcf_idr_insert_many. Since refcount is atleast
one until put_many call, CLS API cannot delete it. Also __tcf_action_put
release path already ensures deterministic outcome (either new action
will be created or existing action will be reused in case CLS API tries
to bind to action concurrently) due to idr lock serialization.

We fix this by making refcount of newly created actions as 2 in ACT API
replace mode. A relaxed store will suffice as visibility is ensured only
after the tcf_idr_insert_many call.

Note that in case of creation or overwriting using CLS API only (i.e.
bind = 1), overwriting existing action object is not allowed, and any
such request is silently ignored (without error).

The refcount bump that occurs in tcf_idr_check_alloc call there for
existing action will pair with tcf_exts_destroy call made from the
owner module for the same action. In case of action creation, there
is no existing action, so no tcf_exts_destroy callback happens.

This means no code changes for CLS API.

Fixes: cae422f379f3 ("net: sched: use reference counting action init")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: net: ethernet-controller: fix typo in NVMEM

commit af9d316f3dd6d1385fbd1631b5103e620fc4298a upstream.

The correct property name is "nvmem-cell-names". This is what:
1. Was originally documented in the ethernet.txt
2. Is used in DTS files
3. Matches standard syntax for phandles
4. Linux net subsystem checks for

Fixes: 9d3de3c58347 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lockdep: Address clang -Wformat warning printing for %hd

commit 6d48b7912cc72275dc7c59ff961c8bac7ef66a92 upstream.

Clang doesn't like format strings that truncate a 32-bit
value to something shorter:

  kernel/locking/lockdep.c:709:4: error: format specifies type 'short' but the argument has type 'int' [-Werror,-Wformat]

In this case, the warning is a slightly questionable, as it could realize
that both class->wait_type_outer and class->wait_type_inner are in fact
8-bit struct members, even though the result of the ?: operator becomes an
'int'.

However, there is really no point in printing the number as a 16-bit
'short' rather than either an 8-bit or 32-bit number, so just change
it to a normal %d.

Fixes: de8f5e4f2dc1 ("lockdep: Introduce wait-type checks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210322115531.3987555-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: socfpga: fix iomem pointer cast on 64-bit

commit 2867b9746cef78745c594894aece6f8ef826e0b4 upstream.

Pointers should be cast with uintptr_t instead of integer.  This fixes
warning when compile testing on ARM64:

  drivers/clk/socfpga/clk-gate.c: In function ‘socfpga_clk_recalc_rate’:
  drivers/clk/socfpga/clk-gate.c:102:7: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]

Fixes: b7cec13f082f ("clk: socfpga: Look for the GPIO_DB_CLK by its offset")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20210314110709.32599-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>