Stefano Babic [Wed, 27 Oct 2010 09:06:20 +0000 (11:06 +0200)]
env_sf: updated to the new environment code
Functions to store/retrieve the environment from a SPI flash was not updated
to the new environment code. The non-redundant case was
not working correctly, reporting ""Environment SPI flash not initialized"
and the code was not compiled clean in the redundant case.
The patch fixes these issue and makes the code more coherent
with other environment storage (nand, flash).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Wolfgang Denk [Wed, 27 Oct 2010 09:06:51 +0000 (11:06 +0200)]
Makefile: fix dependencies for building NAND_SPL
Building of NAND based boards failed sometimes (especially on MP
systems) because of incorrect / missing dependencies.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Wed, 27 Oct 2010 06:31:42 +0000 (08:31 +0200)]
make-asm-offsets: fix sed script
When copying the "sed" script to generate the asm-offsets.h file from
the Linux Kbuild script into the make-asm-offsets file I missed the
fact that the former runs in a "make" context and thus uses double
"$$" to escape a single "$", while the latter is a shell script, where
this must not be done. Unfortunately the problem did not show up
during the initial tests on Power Architecture systems, but on ARM the
generated asm-offsets.h was not correct.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Wolfgang Denk [Wed, 27 Oct 2010 08:29:56 +0000 (10:29 +0200)]
mcu25: fix out of tree building
Out of tree building of the Netstal mcu25 board failed like
that:
Configuring for mcu25 board...
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/fixed_sdram.o: No such file or directory
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/nm_bsp.o: No such file or directory
Adapt (and simplify) the Makefile.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Wolfgang Denk [Tue, 26 Oct 2010 21:42:23 +0000 (23:42 +0200)]
Revert "cmd_net: drop spurious comma in U_BOOT_CMD"
This commit causes build errors like this:
cmd_net.c:301:1: error: macro "U_BOOT_CMD" requires 6 arguments, but only 5 given
cmd_net.c:298: warning: data definition has no type or storage class
cmd_net.c:298: warning: type defaults to 'int' in declaration of 'U_BOOT_CMD'
This reverts commit
8f4cb77ef7183ce1bb3f767604a0677c6f6d84a7.
Wolfgang Denk [Tue, 26 Oct 2010 21:22:36 +0000 (23:22 +0200)]
post/drivers/i2c.c: fix compile error
Commit 7e263ce "post/i2c: Clean up detection logic" added a "const"
qualifier to the declaration of i2c_addr_list[], missing the fact that
the list gets modified later in the code, which results in build
errors like these:
i2c.c: In function 'i2c_post_test':
i2c.c:88: error: assignment of read-only location
Remove the incorrect "const".
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Wolfgang Denk [Sat, 23 Oct 2010 21:22:38 +0000 (23:22 +0200)]
ARM: use the same branch insn on all architectures
For the "fixloop" implementation in start.S a number of different
instructions was used. Unify code so all architectures use "blo"
here because it is more robust in case of incorrect alignments.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.aribaud@free.fr>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Sughosh Ganu [Fri, 22 Oct 2010 19:28:03 +0000 (00:58 +0530)]
Remove config.mk for da8xxevm based boards.
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
now unnecessary config.mk file.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Heiko Schocher [Mon, 25 Oct 2010 06:33:38 +0000 (08:33 +0200)]
arm, bootm: Fix compile warning
Fix warning:
bootm.c: In function 'bootm_linux_fdt':
bootm.c:181: warning: unused variable 's'
bootm.c:180: warning: unused variable 'bd'
Signed-off-by: Heiko Schocher <hs@denx.de>
Mike Frysinger [Wed, 20 Oct 2010 07:33:30 +0000 (03:33 -0400)]
cmd_net: drop spurious comma in U_BOOT_CMD
Building for boards that have CONFIG_CMD_CDP enabled fail with:
cmd_net.c:301: error: expected expression before ',' token
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Darius Augulis [Mon, 25 Oct 2010 10:48:03 +0000 (13:48 +0300)]
arm1176: fix relocation
Fix relocation code for arm1176, do it like other ARM
CPU's are doing.
Tested only with CONFIG_SKIP_RELOCATE_UBOOT defined
and using nand_spl (booting from nand). Test done on
s3c6410 based board (not yet supported in main line).
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Darius Augulis [Mon, 25 Oct 2010 10:45:35 +0000 (13:45 +0300)]
ARM: fix address setup in start.S
Fix address setup bug for ARM.
This bug stops u-boot booting if
CONFIG_SKIP_RELOCATE_UBOOT is defined.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Wolfgang Denk [Tue, 26 Oct 2010 12:34:52 +0000 (14:34 +0200)]
Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Mon, 25 Oct 2010 22:08:35 +0000 (00:08 +0200)]
include/asm-offsets.h: automatically generate assembler constants
A recurrent issue is that certain C level constructs like sizeof() or
offsetof() cannot be used in assembler files, which is inconvenient
when such constructs are used in the definition of macro names etc.
To avoid duplication of such definitions (and thus another cause of
problems), we adapt the Linux way to automatically generate the
respective definitions from the respective C header files.
In Linux, this is implemented in include/linux/kbuild.h, Kbuild, and
arch/*/kernel/asm-offsets.c; we adapt the code from the Linux v2.6.36
kernel tree.
We also copy the concept of the include/generated/ directory which can
be used to hold other automatically generated files as well.
We start with an architecture-independent lib/asm-offsets.c which
generates include/generated/generic-asm-offsets.h (included by
include/asm-offsets.h, which is what will be referred to in the actual
source code). Later this may be extended by architecture-specific
arch/*/lib/asm-offsets.c files that will generate a
include/generated/asm-offsets.h.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Tue, 26 Oct 2010 11:32:32 +0000 (13:32 +0200)]
Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE
No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.
Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken. Last known maintainers on Cc:
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Denk [Tue, 26 Oct 2010 18:58:49 +0000 (20:58 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Tue, 26 Oct 2010 18:57:41 +0000 (20:57 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Tue, 26 Oct 2010 18:55:39 +0000 (20:55 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Gray Remlin [Sun, 24 Oct 2010 15:18:31 +0000 (16:18 +0100)]
ARM: Use consistent assembler syntax
Signed-off-by: Gray Remlin <g_remlin@rocketmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Mike Frysinger [Tue, 19 Oct 2010 22:02:43 +0000 (18:02 -0400)]
Blackfin: adi boards: set compiled size limits
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 19 Oct 2010 06:41:26 +0000 (02:41 -0400)]
Blackfin: bf527-ezkit-v2: move to boards.cfg
Now that the boards.cfg file supports options to mkconfig, we can move
the bf527-ezkit-v2 target out of the Makefile and into boards.cfg.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Dirk Eibach [Thu, 21 Oct 2010 08:50:05 +0000 (10:50 +0200)]
ppc4xx: Add Io and IoCon 405EP board support
Board support for the Guntermann & Drunck CATCenter Io.
Board support for the Guntermann & Drunck IoCon.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Mon, 25 Oct 2010 06:06:52 +0000 (08:06 +0200)]
Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/master
Steve Sakoman [Fri, 22 Oct 2010 20:48:00 +0000 (13:48 -0700)]
ARMV7: OMAP: I2C driver: Fix bug found in 37XX testing
On OMAP36/37XX the standard on chip pullups are not sufficient to
ensure proper i2c operation without external pullups or switching
to high speed mode and enabling special on chip pullups.
This is an issue for Beagle xM, which does not have external pullups
on the expansion board i2c lines.
The issue manifests itself as an AL (arbitration lost) error when
probing for a non-existent device (i.e. on a Beagle xM with no expansion
boards attached). This issue does not occur on expansion boards that
include pullups or on Overo 37XX COM's since they include pull-ups.
This patch fixes the issue by checking for the AL bit in the i2c_probe
function.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Wolfgang Denk [Sun, 24 Oct 2010 14:49:12 +0000 (16:49 +0200)]
hcu4, hcu5: fix out of tree building
Out of tree building of the Netstal hcu4 and hcu5 boards failed like
that:
Assembler messages:
Fatal error: can't create /work/wd/tmp-ppc/board/netstal/hcu4/../common/fixed_sdram.o: No such file or directory
Assembler messages:
Fatal error: can't create /work/wd/tmp-ppc/board/netstal/hcu4/../common/nm_bsp.o: No such file or directory
make[1]: *** [/work/wd/tmp-ppc/board/netstal/hcu4/../common/fixed_sdram.o] Error 2
Adapt (and simplify) the respective Makefiles.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Wolfgang Denk [Sun, 24 Oct 2010 14:07:23 +0000 (16:07 +0200)]
MPC8315ERD: fix build error
Commit 29c6fbe "MPC5121: Add USB EHCI support" renamed
CONFIG_SYS_MPC8xxx_USB_ADDR into CONFIG_SYS_FSL_USB_ADDR but missed
to update arch/powerpc/cpu/mpc83xx/cpu_init.c, resulting in:
cpu_init.c: In function 'cpu_init_f':
cpu_init.c:332: error: 'CONFIG_SYS_MPC8xxx_USB_ADDR' undeclared (first use in this function)
cpu_init.c:332: error: (Each undeclared identifier is reported only once
cpu_init.c:332: error: for each function it appears in.)
make[1]: *** [/work/wd/tmp-ppc/arch/powerpc/cpu/mpc83xx/cpu_init.o] Error 1
Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Sun, 24 Oct 2010 13:46:08 +0000 (15:46 +0200)]
VoVPN-GW_100MHz: drop unsupported board configuration
The 100MHz configuation of the VoVPN-GW has never been supported, so
drop it now.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 24 Oct 2010 13:37:12 +0000 (15:37 +0200)]
lite5200b_PM: fix compile warning
Fix warning:
icecube.c: In function 'lite5200b_wakeup':
icecube.c:83: warning: format '%08lx' expects type 'long unsigned int', but argument 2 has type 'void (*)(void)'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Mike Frysinger [Wed, 20 Oct 2010 07:34:19 +0000 (03:34 -0400)]
MAKEALL: drop non-existent i386 config
Enric Balletbo i Serra [Tue, 19 Oct 2010 09:13:22 +0000 (11:13 +0200)]
ARM: fix relocation support for onenand device.
We also have to relocate the onenand command table manually, otherwise
onenand command don't work.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Andre Schwarz [Fri, 22 Oct 2010 09:21:46 +0000 (11:21 +0200)]
MVBLM7: make TSEC2 work again.
SICRH has been misconfigured, i.e. TSEC2 clock + D[0:3] are GPIOs.
Fix this to be RGMII signals again.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Kumar Gala [Fri, 22 Oct 2010 08:18:13 +0000 (03:18 -0500)]
hwconfig: Utilize getenv_f before relocation to allow for larger buffer
Since we use hwconfig in cases before relocation (like getting DDR
params on FSL PPC systems), we can have strings that exceed the early
small (32 byte) buffer size that getenv will handle.
So we explicitly allocate our own buffer on the stack and use if to
handle getting the hwconfig env string. We currently utilize a string
length of 128 bytes.
This allows us to get rid of boot messages like:
env_buf too small [32]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:24:52 +0000 (00:24 -0500)]
env_flash: Disable debug print statements
With debug the follow is printed:
=> saveenv
Saving Environment to Flash...
Data to save 0x18000
Data (start 0xfff48000, len 0x18000) saved at 0x7fe63f20
Protect off
FFF40000 ...
FFF5FFFF
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... Restoring the rest of data to 0xfff48000 len 0x18000
done
Protected 1 sectors
=>
Without debug:
=> saveenv
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... done
Protected 1 sectors
=>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Wolfgang Denk [Sat, 23 Oct 2010 20:08:33 +0000 (22:08 +0200)]
Merge branch 'for-wd-master' of git://git.denx.de/u-boot-pxa
Wolfgang Denk [Sat, 23 Oct 2010 19:59:42 +0000 (21:59 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Wolfgang Denk [Sat, 23 Oct 2010 19:56:51 +0000 (21:56 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Wolfgang Denk [Sat, 23 Oct 2010 19:49:28 +0000 (21:49 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Wolfgang Denk [Sat, 23 Oct 2010 19:45:57 +0000 (21:45 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Ilya Yanok [Thu, 21 Oct 2010 15:20:13 +0000 (17:20 +0200)]
a4m072: add CONFIG_SYS_FLASH_BANKS_SIZES define
This patch adds CONFIG_SYS_FLASH_BANKS_SIZES define to make use of new
cfi_flash driver ability to detect flash chips that are bigger than a
corresponding address window (we have such situation on some revs of
a4m072).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Ilya Yanok [Thu, 21 Oct 2010 15:20:12 +0000 (17:20 +0200)]
cfi_flash: handle 'chip size exceeds address window' situation
On some boards we have flash mapped high in the address space with
considerably small window (say 0xFE000000 and 32MB). When we install
bigger chip (say 64MB) on such a board strange things happen
(flash_write() doesn't work at all, for ex). That's because cfi_flash
driver doesn't care about window size at all.
Of course, cleanest solution would probably be to just extend address
window to be able to map the whole flash but for legacy/compatibility
reasons some people prefer just truncate the flash size and never use
the upper part.
This patch adds an option for cfi_flash driver to handle this situation
properly. To achieve this we add the new function cfi_flash_bank_size()
which can be provided by the board code and weak-aliased to default
implementation that returns value from the CONFIG_SYS_FLASH_BANKS_SIZES
array if it's defined or 0 otherwise (the last case is added for
compatibility).
If non-zero flash bank size is provided and detected chip size is bigger
than provided address window size the warning will be displayed and
flash chip will be truncated.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Changed cfi_flash_bank_size() return type to unsigned long
to match caller function.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Fri, 22 Oct 2010 12:23:00 +0000 (14:23 +0200)]
ehci-hcd.c: fix hanging under higher load
This patch solves a problem with USB hanging under higher load on a
i.MX31 board. It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.
The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.
Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.
Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Mike Frysinger [Wed, 20 Oct 2010 11:16:04 +0000 (07:16 -0400)]
usb_storage: constify us_direction lookup table
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 20 Oct 2010 11:15:35 +0000 (07:15 -0400)]
usb: musb: constify a bit
These ep and root hub structures need not be writable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Wed, 20 Oct 2010 19:08:17 +0000 (21:08 +0200)]
USB: fix Queue Element Transfer Descriptor changes
Commit 3ed1607 "USB: sync Queue Element Transfer Descriptor against
EHCI spec" added an "__attribute__ ((aligned (32)))" to the
declaration of struct qTD, as used for example in the Linux kernel as
well.
However, it turns out that this attribute causes errors in "usb start"
(like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute
again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Florian Fainelli [Fri, 15 Oct 2010 13:53:45 +0000 (15:53 +0200)]
ehci-pci: print hccr, hcor and hc_lenght
It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was
successfully registered, and at the correct location.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Wolfgang Denk [Fri, 22 Oct 2010 12:08:13 +0000 (14:08 +0200)]
ehci-hcd.c: fix hanging under higher load
This patch solves a problem with USB hanging under higher load on a
i.MX31 board. It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.
The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.
Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.
Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Magnus Sjalander [Wed, 26 May 2010 11:23:53 +0000 (13:23 +0200)]
SPARC: added unaligned definitions
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
John Schmoller [Fri, 22 Oct 2010 05:20:34 +0000 (00:20 -0500)]
XPedite5500 board support
Initial support for Extreme Engineering Solutions XPedite5500 -
a P2020-based PMC/XMC single board computer.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:33 +0000 (00:20 -0500)]
xes: Add POST support for 8xxx boards
Add memory and I2C posts to the XPedite517x/520x/537x board families.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:32 +0000 (00:20 -0500)]
mpc86xx: Add generic POST word read/write support
The PIC's TFRR register doesn't affect hardware and is generally unused,
so use as storage for the POST word.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:31 +0000 (00:20 -0500)]
post/i2c: Add ability to ignore I2C devices
Add the ability to not report an I2C POST error for a set of given I2C
addresses on bootup. This is useful for cases when a device may or may
not be present, and neither case is considered an error. For example:
- Some form factors such as XMC and Compact PCI Express have an I2C
EEPROM whose address changes based on geographical address. Eg
installed in one slot its EEPROM address is, 0x50, in another its
0x51, etc. This allows multiple devices to have their EEPROMs present
on the same I2C bus. Thus the I2C devices present for an XMC or
CPCIe card depend on if and where other cards are installed in the
same system.
- Some cards have optional I2C devices. Eg one hardware build
configuration has different I2C devices than another and software
can't determine if the optional device should be present or not.
- Some cards have optional daughtercards with I2C devices on them.
- I2C EEPROMs address range depends on their size. Its possible to
support differently size EEPROMs by only probing the EEPROM's base
address and ignoring the other addresses that are impacted by its
size.
A new CONFIG_SYS_POST_I2C_IGNORES define has been added which specifies
a list of I2C addresses for the I2C POST to ignore.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:30 +0000 (00:20 -0500)]
post/i2c: Rename I2C_ADDR_LIST to CONFIG_SYS_POST_I2C_ADDRS
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:29 +0000 (00:20 -0500)]
post/i2c: Don't probe address 0
According to the I2C specification device address 0 is the "general call
address", ie a broadcast address. The I2C specification states that the
format of a general call uses at least 2 bytes, which U-Boot's probing
routine does not adhere to.
Not probing device address 0 will prevent possible issues with devices
that accept general calls. Additionally, this change shouldn't reduce
POST coverage since each I2C device should still be accessed via its
own, unique address.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:28 +0000 (00:20 -0500)]
post/i2c: Clean up detection logic
The logic previously used in the I2C post was a bit convoluted.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:27 +0000 (00:20 -0500)]
post/i2c: General clean up
- Clean up ifdeffery
- Update coding style
No functional change should have occurred.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 22 Oct 2010 05:20:26 +0000 (00:20 -0500)]
xes: Make X-ES board names more generic
Some U-Boot images for X-ES boards support multiple products in the same
family. For example, the XPedite5370, XPedite5371, and XPedite5372 are
similar enough that one U-Boot image can work on all 3 cards. To make it
clear that a U-Boot image can work on boards of the same family, rename
the boards with the least significant digit of 'x'.
While we're at it, change the board config file and make targets to be
lowercase.
Also change the default uImage and fdt filenames to "board.uImage" and
"board.dtb" to be more generic.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
John Schmoller [Fri, 22 Oct 2010 05:20:25 +0000 (00:20 -0500)]
xes: Add board_flash_wp_on()
Add board_flash_wp_on() to check a pca9557 gpio pin to see
if non-volatile memory write protection is enabled.
Previously, write protected NOR flashes would fail initialization which
resulted in a bootup error such as:
...
DTT: 53 C local / 64 C remote (adt7461@4c)
DTT: 54 C local (ds1621@48)
FLASH: Executed from FLASH1
POST memory PASSED
FLASH: ## Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
## Unknown FLASH on Bank 2 - Size = 0x00000000 = 0 MB
*** failed ***
### ERROR ### Please RESET the board ###
With this patch, NOR flash initialization is skipped:
...
DTT: 53 C local / 64 C remote (adt7461@4c)
DTT: 54 C local (ds1621@48)
FLASH: Executed from FLASH1
POST memory PASSED
FLASH: Uninitialized - Write Protect On
L2: 1024 KB enabled
NAND: 1024 MiB
...
Note that flash related commands such as flinfo and saveenv will error
out when flash write protection is enabled.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
John Schmoller [Fri, 22 Oct 2010 05:20:24 +0000 (00:20 -0500)]
xes: Consolidate checkboard()
Create a common checkboard() function to support all X-ES's Freescale
boards.
Also, add a get_board_derivative() function which reads hardware
strapping resistors to determine what model a board is. This allows one
U-Boot image to support multiple boards.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
John Schmoller [Fri, 22 Oct 2010 05:20:23 +0000 (00:20 -0500)]
pci: Add ability to re-enumerate PCI buses
Add a new 'pci enum' command which re-enumerates the PCI buses. This
command is enabled via the CONFIG_CMD_PCI_ENUM define and can be useful
in boards with FPGAs connected via PCI/PCIe, boards that support PCI
hot-plugging, or during PCI debug.
Also enable the 'pci enum' command for X-ES's Freescale-based boards.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Peter Tyser [Fri, 22 Oct 2010 05:20:22 +0000 (00:20 -0500)]
xes: Use common PCI initialization code
Common Freescale code for PCI initialization now exists, so migrate X-ES
boards to use it.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 22 Oct 2010 06:32:56 +0000 (01:32 -0500)]
corenet_ds: Update CONFIG_SYS_GBL_DATA_SIZE to deal with growth in gd_t
The recent change the env code added an additional 32 bytes into gd_t
and that causes to grow pass the previous CONFIG_SYS_GBL_DATA_SIZE size.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Marek Vasut [Wed, 20 Oct 2010 20:01:12 +0000 (22:01 +0200)]
PXA: Remove "xsengine" board
This board is broken and it's not possible to repair it.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:37:14 +0000 (21:37 +0200)]
PXA: Remove "wepep250" board
This board is broken and impossible to repair without deep knowledge or
availability of the hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 18:48:43 +0000 (20:48 +0200)]
PXA: Remove "delta" board
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 20:02:16 +0000 (22:02 +0200)]
PXA: zipitz2: Add missing CONFIG_SYS_TEXT_BASE
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:30:03 +0000 (21:30 +0200)]
PXA: vpac270: Add missing CONFIG_SYS_TEXT_BASE
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:57:34 +0000 (21:57 +0200)]
PXA: xm250: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:54:19 +0000 (21:54 +0200)]
PXA: xaeniax: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:28:14 +0000 (21:28 +0200)]
PXA: trizepsiv: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:20:07 +0000 (21:20 +0200)]
PXA: pxa255_idp: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:10:25 +0000 (21:10 +0200)]
PXA: pleb2: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:06:23 +0000 (21:06 +0200)]
PXA: palmtc: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 19:04:13 +0000 (21:04 +0200)]
PXA: palmld: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 18:55:44 +0000 (20:55 +0200)]
PXA: lubbock: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 18:52:21 +0000 (20:52 +0200)]
PXA: innokom: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 18:43:41 +0000 (20:43 +0200)]
PXA: csb226: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 18:17:51 +0000 (20:17 +0200)]
PXA: cradle: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 18:15:11 +0000 (20:15 +0200)]
PXA: colibri_pxa270: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 16:56:41 +0000 (18:56 +0200)]
PXA: cerf250: Fix for reloc
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 18:09:09 +0000 (20:09 +0200)]
PXA: Use pxa-regs.h register definitions in start.S
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Wed, 20 Oct 2010 17:36:39 +0000 (19:36 +0200)]
PXA: Implement ELF relocation
Based on patch by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Stefano Babic [Thu, 21 Oct 2010 08:34:39 +0000 (10:34 +0200)]
MX51: Add video support to vision2 board
The patch adds support for LCD to the vision2 board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Wed, 13 Oct 2010 10:17:14 +0000 (12:17 +0200)]
MX51: Add video support
Add framebuffer driver for the MX51 processor
working on the IPUv3 internal graphic processor.
The port is based on the driver found in the kernel
delivered by Freescale as part of i.MX BSP:
[kernel 2.6.31 commit
cc4fe714041805997b601fe8e5dd585d8a99297f]
[agust@denx.de: some style fixes and dead code removal]
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Stefano Babic [Wed, 13 Oct 2010 10:16:35 +0000 (12:16 +0200)]
MX51: Add IPU driver for video support
The patch is a porting of the IPU Linux driver
developed by Freescale to have framebuffer
functionalities in u-boot. The port is based on
kernel 2.6.31 commit
cc4fe714041805997b601fe8e5dd585d8a99297f,
as delivered by Freescale [i.MX BSP].
Most features are dropped from the original driver and
only LCD support is the goal of this porting.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Wed, 13 Oct 2010 10:14:29 +0000 (12:14 +0200)]
Add linux framebuffer header include/linux/fb.h
[port of linux 2.6.34 commit
6a9ee8af344e3bd7dbd61e67037096cdf7f83289]
Signed-off-by: Stefano Babic <sbabic@denx.de>
Ilya Yanok [Thu, 21 Oct 2010 15:20:11 +0000 (17:20 +0200)]
led_display: remove unused DISPLAY_MARK define
DISPLAY_MARK subcommand of display_set() is not used anywhere so
we can remove it safely.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Ilya Yanok [Thu, 21 Oct 2010 15:20:10 +0000 (17:20 +0200)]
a4m072: change 'display' command implementation
This patch changes implementation of 'display' command for a4m072
that uses 7-segment LED display as customer requested:
a) The "display" command shall _not_ turn on the decimal point.
b) Exception: "display ." shall turn on (only) the decimal point.
c) Hex digits (0-9, A-F, a-f) shall be displayed as usual.
d) Letters U, P, Y, L, S, T, H shall be displayed as usual (lower
case letters identical to upper case letters)
e) 'I' (and 'i') shall be displayed like '1'
f) 'O' (and 'o') shall be displayed like '0'
g) all other Characters shall be displayed like ' ' (all segments off).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Ilya Yanok [Thu, 21 Oct 2010 15:20:09 +0000 (17:20 +0200)]
a4m072: changes to the default environment
The default values for 'addip' and 'norargs' changed per customer
request. Everything else cleaned up to fit into 80 symbol line.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Anatolij Gustschin [Thu, 21 Oct 2010 16:30:35 +0000 (18:30 +0200)]
Fix building for 83xx boards with USB support
Commit
29c6fbe0471afd7ffa41fcb2103eec5b53294897 broke
building for 83xx boards with USB support:
ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43: error: 'CONFIG_SYS_FSL_USB_ADDR' undeclared (first use in this function)
ehci-fsl.c:43: error: (Each undeclared identifier is reported only once
ehci-fsl.c:43: error: for each function it appears in.)
make[1]: *** [ehci-fsl.o] Error 1
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Nobuhiro Iwamatsu [Tue, 19 Oct 2010 16:35:28 +0000 (01:35 +0900)]
sh: sh4: Move to boards.cfg
Move the sh4 target boards out of the Makefile and into boards.cfg.
And fix sh4 of MAKEALL.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 19 Oct 2010 16:28:29 +0000 (01:28 +0900)]
sh: sh3: Move to boards.cfg
Move the sh3 target boards out of the Makefile and into boards.cfg.
And fix sh3 of MAKEALL.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 19 Oct 2010 16:22:25 +0000 (01:22 +0900)]
sh: rsk7203: Move to boards.cfg
Move the rsk7203 target out of the Makefile and into boards.cfg.
And fix sh2 of MAKEALL.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 19 Oct 2010 16:17:08 +0000 (01:17 +0900)]
sh: sh7785lcr: Add CONFIG_SYS_TEXT_BASE for 32bit mode
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 19 Oct 2010 08:14:15 +0000 (17:14 +0900)]
sh: Fix warning about uninitialized value of ramdisk_flags
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 19 Oct 2010 08:07:07 +0000 (17:07 +0900)]
sh: Rename TEXT_BASE to CONFIG_SYS_TEXT_BASE
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 5 Oct 2010 07:58:05 +0000 (16:58 +0900)]
sh: sh7785lcr: Add CONFIG_SH_SDRAM_OFFSET
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 28 Sep 2010 03:14:57 +0000 (12:14 +0900)]
sh: Add support load and boot of Initrd.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
John Schmoller [Wed, 29 Sep 2010 19:05:44 +0000 (14:05 -0500)]
ppc: Don't initialize write protected NOR flashes
If a NOR flash is write protected it can not be initialized/detected so
add the ability for boards to skip NOR initialization on bootup. A
board can skip NOR initialization by implementing the
board_flash_wp_on() function.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: sr@denx.de
Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Wed, 20 Oct 2010 06:31:45 +0000 (08:31 +0200)]
MPC52xx, motionpro: update default configuration
Signed-off-by: Wolfgang Denk <wd@denx.de>
Macpaul Lin [Tue, 19 Oct 2010 12:14:36 +0000 (20:14 +0800)]
ftrtc010.c : enhance code according to original datasheet
Add missing codes according to original datasheet.
This patch also makes ftrtc010 could be adapted to PCLK and EXT_CLK.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>