drm/msm/dsi: Use DSC slice(s) packet size to compute word count

According to downstream the value to use for WORD_COUNT is
bytes_per_pkt, which denotes the number of bytes in a packet based on
how many slices have been configured by the panel driver times the
width of a slice times the number of bytes per pixel.

The DSC panels seen thus far use one byte per pixel, only one slice
per packet, and a slice width of half the panel width leading to the
desired bytes_per_pkt+1 value to be equal to hdisplay/2+1.  This however
isn't the case anymore for panels that configure two slices per packet,
where the value should now be hdisplay+1.

Note that the aforementioned panel (on a Sony Xperia XZ3, sdm845) with
slice_count=1 has also been tested to successfully accept slice_count=2,
which would have shown corrupted output previously.

Fixes: 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515694/
Link: https://lore.kernel.org/r/20221221231943.1961117-3-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Wire up DSC mask for active CTL configuration

Active CTLs have to configure what DSC block(s) have to be enabled, and
what DSC block(s) have to be flushed; this value was initialized to zero
resulting in the necessary register writes to never happen (or would
write zero otherwise).  This seems to have gotten lost in the DSC v4->v5
series while refactoring how the combination with merge_3d was handled.

Fixes: 58dca9810749 ("drm/msm/disp/dpu1: Add support for DSC in encoder")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515693/
Link: https://lore.kernel.org/r/20221221231943.1961117-2-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: mdss: add support for SM8550

Add support for the MDSS block on SM8550 platform.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/517516/
Link: https://lore.kernel.org/r/20230103-topic-sm8550-upstream-mdss-dsi-v3-5-660c3bcb127f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: add support for SM8550

Add definitions for the display hardware used on Qualcomm SM8550
platform.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/517512/
Link: https://lore.kernel.org/r/20230103-topic-sm8550-upstream-mdss-dsi-v3-4-660c3bcb127f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: Introduce SC8280XP MDSS

Add compatible for the SC8280XP Mobile Display Subsystem and
initialization for version 8.0.0.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514402/
Link: https://lore.kernel.org/r/20221207220012.16529-4-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Introduce SC8280XP

The Qualcomm SC8280XP platform contains DPU version 8.0.0, has 9
interfaces, 2 DSI controllers and 4 DisplayPort controllers. Extend the
necessary definitions and describe the DPU in the SC8280XP.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514398/
Link: https://lore.kernel.org/r/20221207220012.16529-3-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: Add binding for SC8280XP MDSS

Add binding for the display subsystem and display processing unit in the
Qualcomm SC8280XP platform.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/514396/
Link: https://lore.kernel.org/r/20221207220012.16529-2-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: Add support for SM8350

Add compatibles string, "qcom,sm8350-mdss", for the multimedia display
subsystem unit used on Qualcomm SM8350 platform.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/516345/
Link: https://lore.kernel.org/r/20221230153554.105856-6-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: disable DSC blocks for SM8350

SM8350 has newer version of DSC blocks, which are not supported by the
driver yet. Remove them for now until these blocks are supported by the
driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/517629/
Link: https://lore.kernel.org/r/20230109214309.586130-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Add support for SM8350

Add compatibles string, "qcom,sm8350-dpu", for the display processing unit
used on Qualcomm SM8350 platform.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516342/
Link: https://lore.kernel.org/r/20221230153554.105856-5-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Add SM8350 to hw catalog

Add compatibility for SM8350 display subsystem, including
required entries in DPU hw catalog.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516340/
Link: https://lore.kernel.org/r/20221230153554.105856-4-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display: msm: Add qcom, sm8350-mdss binding

Mobile Display Subsystem (MDSS) encapsulates sub-blocks
like DPU display controller, DSI etc. Add YAML schema for MDSS device
tree bindings

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/516338/
Link: https://lore.kernel.org/r/20221230153554.105856-3-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display: msm: Add qcom, sm8350-dpu binding

Mobile Display Subsystem (MDSS) encapsulates sub-blocks
like DPU display controller, DSI etc. Add YAML schema for DPU device
tree bindings

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/516337/
Link: https://lore.kernel.org/r/20221230153554.105856-2-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: mdss add support for SM8450

Add support for the MDSS block on SM8450 platform.

Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514247/
Link: https://lore.kernel.org/r/20221207012231.112059-12-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: add support for SM8450

Add definitions for the display hardware used on Qualcomm SM8450
platform.

Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514235/
Link: https://lore.kernel.org/r/20221207012231.112059-11-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: add support for MDP_TOP blackhole

On sm8450 a register block was removed from MDP TOP. Accessing it during
snapshotting results in NoC errors / immediate reboot. Skip accessing
these registers during snapshot.

Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514239/
Link: https://lore.kernel.org/r/20221207012231.112059-10-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: merge all MDP TOP registers to dpu_hwio.h

There is a separate header containing some of MDP TOP register
definitions, dpu_hwio.h. Move missing register definitions from
dpu_hw_top.c to the mentioned header.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514242/
Link: https://lore.kernel.org/r/20221207012231.112059-9-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: add support for the display on SM8450

Add DPU and MDSS schemas to describe MDSS and DPU blocks on the Qualcomm
SM8450 platform.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514234/
Link: https://lore.kernel.org/r/20221207012231.112059-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: *dpu.yaml: split required properties clauses

Require only properties declared in given schema, which makes the code a
bit more readable and easy to follow.

Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514229/
Link: https://lore.kernel.org/r/20221207012231.112059-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display: msm: drop redundant part of title

The Devicetree bindings document does not have to say in the title that
contains "DT properties", but instead just describe the hardware.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/516033/
Link: https://lore.kernel.org/r/20221225115925.55337-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Print interrupt index in addition to the mask

The mask only describes the `irq_idx % 32` part, making it generally
impossible to deduce what interrupt is being enabled/disabled.  Since
`debug/core_irq` in debugfs (and other prints) also include the full
`DPU_IRQ_IDX()` value, print the same full value here for easier
correlation instead of only adding the `irq_idx / 32` part.

Furthermore, make the dbgstr messages more consistent.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/512460/
Link: https://lore.kernel.org/r/20221121222456.437815-1-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: check for null return of devm_kzalloc() in dpu_writeback_init()

Because of the possilble failure of devm_kzalloc(), dpu_wb_conn might
be NULL and will cause null pointer dereference later.

Therefore, it might be better to check it and directly return -ENOMEM.

Fixes: 77b001acdcfe ("drm/msm/dpu: add the writeback connector layer")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/512277/
Link: https://lore.kernel.org/r/20221119055518.179937-1-tanghui20@huawei.com
[DB: fixed typo in commit message]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu1: Remove INTF4 IRQ from SDM845 IRQ mask

SDM845 only has INTF0-3 and has no business caring about the INTF4 irq.

Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/510463/
Link: https://lore.kernel.org/r/20221107103739.8993-1-konrad.dybcio@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/a6xx: Avoid gx gbit halt during rpm suspend

As per the downstream driver, gx gbif halt is required only during
recovery sequence. So lets avoid it during regular rpm suspend.

Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515279/
Link: https://lore.kernel.org/r/20221216223253.1.Ice9c47bfeb1fddb8dc377a3491a043a3ee7fca7d@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/adreno: Make adreno quirks not overwrite each other

So far the adreno quirks have all been assigned with an OR operator,
which is problematic, because they were assigned consecutive integer
values, which makes checking them with an AND operator kind of no bueno..

Switch to using BIT(n) so that only the quirks that the programmer chose
are taken into account when evaluating info->quirks & ADRENO_QUIRK_...

Fixes: 370063ee427a ("drm/msm/adreno: Add A540 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/516456/
Link: https://lore.kernel.org/r/20230102100201.77286-1-konrad.dybcio@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: another fix for the headless Adreno GPU

Fix another oops reproducible when rebooting the board with the Adreno
GPU working in the headless mode (e.g. iMX platforms).

Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
[00000000] *pgd=74936831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] ARM
CPU: 0 PID: 51 Comm: reboot Not tainted 6.2.0-rc1-dirty #11
Hardware name: Freescale i.MX53 (Device Tree Support)
PC is at msm_atomic_commit_tail+0x50/0x970
LR is at commit_tail+0x9c/0x188
pc : [<c06aa430>]    lr : [<c067a214>]    psr: 600e0013
sp : e0851d30  ip : ee4eb7eb  fp : 00090acc
r10: 00000058  r9 : c2193014  r8 : c4310000
r7 : c4759380  r6 : 07bef61d  r5 : 00000000  r4 : 00000000
r3 : c44cc440  r2 : 00000000  r1 : 00000000  r0 : 00000000
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: 74910019  DAC: 00000051
Register r0 information: NULL pointer
Register r1 information: NULL pointer
Register r2 information: NULL pointer
Register r3 information: slab kmalloc-1k start c44cc400 pointer offset 64 size 1024
Register r4 information: NULL pointer
Register r5 information: NULL pointer
Register r6 information: non-paged memory
Register r7 information: slab kmalloc-128 start c4759380 pointer offset 0 size 128
Register r8 information: slab kmalloc-2k start c4310000 pointer offset 0 size 2048
Register r9 information: non-slab/vmalloc memory
Register r10 information: non-paged memory
Register r11 information: non-paged memory
Register r12 information: non-paged memory
Process reboot (pid: 51, stack limit = 0xc80046d9)
Stack: (0xe0851d30 to 0xe0852000)
1d20:                                     c4759380 fbd77200 000005ff 002b9c70
1d40: c4759380 c4759380 00000000 07bef61d 00000600 c0d6fe7c c2193014 00000058
1d60: 00090acc c067a214 00000000 c4759380 c4310000 00000000 c44cc854 c067a89c
1d80: 00000000 00000000 00000000 c4310468 00000000 c4759380 c4310000 c4310468
1da0: c4310470 c0643258 c4759380 00000000 00000000 c0c4ee24 00000000 c44cc810
1dc0: 00000000 c0c4ee24 00000000 c44cc810 00000000 0347d2a8 e0851e00 e0851e00
1de0: c4759380 c067ad20 c4310000 00000000 c44cc810 c27f8718 c44cc854 c067adb8
1e00: c4933000 00000002 00000001 00000000 00000000 c2130850 00000000 c2130854
1e20: c25fc488 00000000 c0ff162c 00000000 00000001 00000002 00000000 00000000
1e40: c43102c0 c43102c0 00000000 0347d2a8 c44cc810 c44cc814 c2133da8 c06d1a60
1e60: 00000000 00000000 00079028 c2012f24 fee1dead c4933000 00000058 c01431e4
1e80: 01234567 c0143a20 00000000 00000000 00000000 00000000 00000000 00000000
1ea0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1ec0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1ee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f00: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f20: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f80: 00000000 00000000 00000000 0347d2a8 00000002 00000004 00000078 00000058
1fa0: c010028c c0100060 00000002 00000004 fee1dead 28121969 01234567 00079028
1fc0: 00000002 00000004 00000078 00000058 0002fdc5 00000000 00000000 00090acc
1fe0: 00000058 becc9c64 b6e97e05 b6e0e5f6 600e0030 fee1dead 00000000 00000000
 msm_atomic_commit_tail from commit_tail+0x9c/0x188
 commit_tail from drm_atomic_helper_commit+0x160/0x188
 drm_atomic_helper_commit from drm_atomic_commit+0xac/0xe0
 drm_atomic_commit from drm_atomic_helper_disable_all+0x1b0/0x1c0
 drm_atomic_helper_disable_all from drm_atomic_helper_shutdown+0x88/0x140
 drm_atomic_helper_shutdown from device_shutdown+0x16c/0x240
 device_shutdown from kernel_restart+0x38/0x90
 kernel_restart from __do_sys_reboot+0x174/0x224
 __do_sys_reboot from ret_fast_syscall+0x0/0x1c
Exception stack(0xe0851fa8 to 0xe0851ff0)
1fa0:                   00000002 00000004 fee1dead 28121969 01234567 00079028
1fc0: 00000002 00000004 00000078 00000058 0002fdc5 00000000 00000000 00090acc
1fe0: 00000058 becc9c64 b6e97e05 b6e0e5f6
Code: 15922088 1184421c e1500003 1afffff8 (e5953000)
---[ end trace 0000000000000000 ]---

Fixes: 0a58d2ae572a ("drm/msm: Make .remove and .shutdown HW shutdown consistent")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/516909/
Link: https://lore.kernel.org/r/20230105014743.1478110-1-dmitry.baryshkov@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

dt-bindings: msm: dsi-controller-main: Fix description of core clock

There's a typo in describing the core clock as an 'escape' clock. The
accurate description is 'core'.

Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515938/
Link: https://lore.kernel.org/r/20221223021025.1646636-4-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

dt-bindings: msm: dsi-controller-main: Fix power-domain constraint

power-domain is required for the sc7180 dispcc GDSC but not every qcom SoC
has a similar dependency for example the apq8064.

Most Qcom SoC's using mdss-dsi-ctrl seem to have the ability to
power-collapse the MDP without collapsing DSI.

For example the qcom vendor kernel commit for apq8084, msm8226, msm8916,
msm8974.

https://review.carbonrom.org/plugins/gitiles/CarbonROM/android_kernel_oneplus_msm8994/+/7b5c011a770daa2811778937ed646237a28a8694

"ARM: dts: msm: add mdss gdsc supply to dsi controller device

 It is possible for the DSI controller to be active when MDP is
 power collapsed. DSI controller needs to have it's own vote for
 mdss gdsc to ensure that gdsc remains on in such cases."

This however doesn't appear to be the case for the apq8064 so we shouldn't
be marking power-domain as required in yaml checks.

Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515958/
Link: https://lore.kernel.org/r/20221223021025.1646636-3-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

dt-bindings: msm: dsi-controller-main: Fix operating-points-v2 constraint

The existing msm8916.dtsi does not depend on nor require operating points.

Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/515940/
Link: https://lore.kernel.org/r/20221223021025.1646636-2-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

dt-bindings: msm: dsi-phy-28nm: Add missing qcom, dsi-phy-regulator-ldo-mode

Add in missing qcom,dsi-phy-regulator-ldo-mode to the 28nm DSI PHY.
When converting from .txt to .yaml we missed this one.

Fixes: 4dbe55c97741 ("dt-bindings: msm: dsi: add yaml schemas for DSI bindings")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516205/
Link: https://lore.kernel.org/r/20221229124438.504770-2-bryan.odonoghue@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

drm/msm/dp: do not complete dp_aux_cmd_fifo_tx() if irq is not for aux transfer

There are 3 possible interrupt sources are handled by DP controller,
HPDstatus, Controller state changes and Aux read/write transaction.
At every irq, DP controller have to check isr status of every interrupt
sources and service the interrupt if its isr status bits shows interrupts
are pending. There is potential race condition may happen at current aux
isr handler implementation since it is always complete dp_aux_cmd_fifo_tx()
even irq is not for aux read or write transaction. This may cause aux read
transaction return premature if host aux data read is in the middle of
waiting for sink to complete transferring data to host while irq happen.
This will cause host's receiving buffer contains unexpected data. This
patch fixes this problem by checking aux isr and return immediately at
aux isr handler if there are no any isr status bits set.

Current there is a bug report regrading eDP edid corruption happen during
system booting up. After lengthy debugging to found that VIDEO_READY
interrupt was continuously firing during system booting up which cause
dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data
from aux hardware buffer which is not yet contains complete data transfer
from sink. This cause edid corruption.

Follows are the signature at kernel logs when problem happen,
EDID has corrupt header
panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID

Changes in v2:
-- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr()
-- add more commit text

Changes in v3:
-- add Stephen suggested
-- dp_aux_isr() return IRQ_XXX back to caller
-- dp_ctrl_isr() return IRQ_XXX back to caller

Changes in v4:
-- split into two patches

Changes in v5:
-- delete empty line between tags

Changes in v6:
-- remove extra "that" and fixed line more than 75 char at commit text

Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/516121/
Link: https://lore.kernel.org/r/1672193785-11003-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

drm/msm/hdmi: Fix the error handling path of msm_hdmi_dev_probe()

If an error occurs after a successful msm_hdmi_get_phy() call, it must be
undone by a corresponding msm_hdmi_put_phy(), as already done in the
remove function.

Fixes: 437365464043 ("drm/msm/hdmi: move msm_hdmi_get_phy() to msm_hdmi_dev_probe()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514847/
Link: https://lore.kernel.org/r/b3f9da097851e2e42a40dc61458aa98c41c88d0d.1670741386.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

drm/msm/dpu: Fix memory leak in msm_mdss_parse_data_bus_icc_path

of_icc_get() alloc resources for path1, we should release it when not
need anymore. Early return when IS_ERR_OR_NULL(path0) may leak path1.
Defer getting path1 to fix this.

Fixes: b9364eed9232 ("drm/msm/dpu: Move min BW request and full BW disable back to mdss")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/514264/
Link: https://lore.kernel.org/r/20221207065922.2086368-1-linmq006@gmail.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

dt-bindings: display: msm: Rename mdss node name in example

Follow other YAMLs and replace mdss name into display-subystem.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: b93bdff44a85 ("dt-bindings: display/msm: add support for SM6115")
Fixes: 06097b13ef97 ("dt-bindings: display/msm: split dpu-qcm2290 into DPU and MDSS parts")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/513585/
Link: https://lore.kernel.org/r/20221130200950.144618-2-a39.skl@gmail.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

dt-bindings: msm/dsi: Don't require vdds-supply on 10nm PHY

On some SoCs (hello SM6350) vdds-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX/mx.lvl line,
which is voted for in the DSI ctrl node.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: 8fc939e72ff8 ("dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/511889/
Link: https://lore.kernel.org/r/20221116163218.42449-1-konrad.dybcio@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

dt-bindings: msm/dsi: Don't require vcca-supply on 14nm PHY

On some SoCs (hello SM6115) vcca-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX line, which is
voted for in the DSI ctrl node.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 8fc939e72ff8 ("dt-bindings: msm: dsi: add yaml schemas for DSI PHY bindings")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/513555/
Link: https://lore.kernel.org/r/20221130135807.45028-1-konrad.dybcio@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

drm/msm/dpu: Fix some kernel-doc comments

Make the description of @init to @p in dpu_encoder_phys_wb_init()
and remove @wb_roi in dpu_encoder_phys_wb_setup_fb() to clear the below
warnings:

drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c:139: warning: Excess function parameter 'wb_roi' description in 'dpu_encoder_phys_wb_setup_fb'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c:699: warning: Function parameter or member 'p' not described in 'dpu_encoder_phys_wb_init'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder_phys_wb.c:699: warning: Excess function parameter 'init' description in 'dpu_encoder_phys_wb_init'

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3067
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Fixes: d7d0e73f7de3 ("drm/msm/dpu: introduce the dpu_encoder_phys_* for writeback")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/511605/
Link: https://lore.kernel.org/r/20221115014902.45240-1-yang.lee@linux.alibaba.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>

Merge branches 'msm-next-lumag-core', 'msm-next-lumag-dpu', 'msm-next-lumag-dp', 'msm-next-lumag-dsi', 'msm-next-lumag-hdmi' and 'msm-next-lumag-mdp5' into msm-next-lumag

Core:
- MSM_INFO_GET_FLAGS support
- Cleaned up MSM IOMMU wrapper code

DPU:
- Added support for XR30 and P010 image formats
- Reworked MDSS/DPU schema, added SM8250 MDSS bindings
- Added Qualcomm SM6115 support

DP:
- Dropped unsane sanity checks

DSI:
- Fix calculation of DSC pps payload

DSI PHY:
- DSI PHY support for QCM2290

HDMI:
- Reworked dev init path

And, as usual, small misc fixes.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/disp/dpu1: add support for display on SM6115

Add required display hw catalog changes for SM6115.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/512875/
Link: https://lore.kernel.org/r/20221124001708.25720-3-a39.skl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: add support for SM6115

Add DPU and MDSS schemas to describe MDSS and DPU blocks on the Qualcomm
SM6115 platform.
Configuration for DSI/PHY is shared with QCM2290 so compatibles are reused.
Lack of dsi phy supply in example is intended
due to fact on qcm2290, sm6115 and sm6125
this phy is supplied via power domain, not regulator.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/512872/
Link: https://lore.kernel.org/r/20221124001708.25720-2-a39.skl@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/mdp5: fix reading hw revision on db410c platform

Since the commit commit c6122688f265 ("drm/msm/mdp5: stop overriding
drvdata") reading the MDP5 hw revision on db410c will crash the board
as the MDSS_GDSC is not enabled. Revert a part of the offending commit
(moving rpm enablement) and set priv->kms earlier. This make it possible
to use pm_runtime_get_sync() during read_mdp_hw_revision(), which will
power up both the MDP5 and MDSS devices.

Fixes: c6122688f265 ("drm/msm/mdp5: stop overriding drvdata")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/512985/
Link: https://lore.kernel.org/r/20221125000213.252115-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/hdmi: remove unnecessary NULL check

This code was recently refactored in commit and now the "hdmi" pointer
can't be NULL.  Checking for NULL leads to a Smatch warning:

    drivers/gpu/drm/msm/hdmi/hdmi.c:141 msm_hdmi_init()
    warn: variable dereferenced before check 'hdmi' (see line 119)

Fixes: 69a88d8633ec ("drm/msm/hdmi: move resource allocation to probe function")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/512163/
Link: https://lore.kernel.org/r/Y3eCqQ2pm1uQnktV@kadam
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: msm: dsi-controller-main: Drop redundant phy-names

Adding in msm8939 which is based msm8916 dtsi I stumbled across a binding
check complaining about the phy name for msm8916 which we were reusing for
msm8939.

The currently inconsistent upstream dtsi naming of "dsi" and "dsi-phy" is
not captured in the yaml for this driver.

The driver however doesn't care about the name of DSI phy, hence the yaml
check is redundant.

Both Krzysztof and Rob suggested we could drop the phy-names entirely if it
really isn't a dependency.

So, drop the inconsistent and unnecessary phy-names field from the yaml.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm/dsi-controller-main: allow defining opp-table

Allow defining DSI OPP table inside the DSI controller node.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Prevent signed BPG offsets from bleeding into adjacent bits

The bpg_offset array contains negative BPG offsets which fill the full 8
bits of a char thanks to two's complement: this however results in those
bits bleeding into the next field when the value is packed into DSC PPS
by the drm_dsc_helper function, which only expects range_bpg_offset to
contain 6-bit wide values.  As a consequence random slices appear
corrupted on-screen (tested on a Sony Tama Akatsuki device with sdm845).

Use AND operators to limit these two's complement values to 6 bits,
similar to the AMD and i915 drivers.

Fixes: b9080324d6ca ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508941/
Link: https://lore.kernel.org/r/20221026182824.876933-11-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu1: Account for DSC's bits_per_pixel having 4 fractional bits

According to the comment this DPU register contains the bits per pixel
as a 6.4 fractional value, conveniently matching the contents of
bits_per_pixel in struct drm_dsc_config which also uses 4 fractional
bits.  However, the downstream source this implementation was
copy-pasted from has its bpp field stored _without_ fractional part.

This makes the entire convoluted math obsolete as it is impossible to
pull those 4 fractional bits out of thin air, by somehow trying to reuse
the lowest 2 bits of a non-fractional bpp (lsb = bpp % 4??).

The rest of the code merely attempts to keep the integer part a multiple
of 4, which is rendered useless thanks to data |= dsc->bits_per_pixel <<
12; already filling up those bits anyway (but not on downstream).

Fixes: c110cfd1753e ("drm/msm/disp/dpu1: Add support for DSC")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/508946/
Link: https://lore.kernel.org/r/20221026182824.876933-10-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Disallow 8 BPC DSC configuration for alternative BPC values

According to the `/* bpc 8 */` comment below only values for a
bits_per_component of 8 are currently hardcoded in place.  This is
further confirmed by downstream sources [1] containing different
constants for other BPC values (and different initial_offset too,
with an extra dependency on bits_per_pixel).  Prevent future mishaps by
explicitly disallowing any other bits_per_component value until the
right parameters are put in place and tested.

[1]: https://git.codelinaro.org/clo/la/platform/vendor/opensource/display-drivers/-/blob/DISPLAY.LA.2.0.r1-08000-WAIPIO.0/msm/sde_dsc_helper.c#L110-139

Fixes: b9080324d6ca ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508942/
Link: https://lore.kernel.org/r/20221026182824.876933-9-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Account for DSC's bits_per_pixel having 4 fractional bits

drm_dsc_config's bits_per_pixel field holds a fractional value with 4
bits, which all panel drivers should adhere to for
drm_dsc_pps_payload_pack() to generate a valid payload.  All code in the
DSI driver here seems to assume that this field doesn't contain any
fractional bits, hence resulting in the wrong values being computed.
Since none of the calculations leave any room for fractional bits or
seem to indicate any possible area of support, disallow such values
altogether.  calculate_rc_params() in intel_vdsc.c performs an identical
bitshift to get at this integer value.

Fixes: b9080324d6ca ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508938/
Link: https://lore.kernel.org/r/20221026182824.876933-8-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Migrate to drm_dsc_compute_rc_parameters()

As per the FIXME this code is entirely duplicate with what is already
provided inside drm_dsc_compute_rc_parameters(), supposedly because that
function was yielding "incorrect" results while in reality the panel
driver(s?) used for testing were providing incorrect parameters.

For example, this code from downstream assumed dsc->bits_per_pixel to
contain an integer value, whereas the upstream drm_dsc_config struct
stores it with 4 fractional bits.  drm_dsc_compute_rc_parameters()
already accounts for this feat while the panel driver used for testing
[1] wasn't, hence making drm_dsc_compute_rc_parameters() seem like it
was returning an incorrect result.
Other users of dsc->bits_per_pixel inside dsi_populate_dsc_params() also
treat it in the same erroneous way, and will be addressed in a separate
patch.
In the end, using drm_dsc_compute_rc_parameters() spares both a lot of
duplicate code and erratic behaviour.

[1]: https://git.linaro.org/people/vinod.koul/kernel.git/commit/?h=topic/pixel3_5.18-rc1&id=1d7d98ad564f1ec69e7525e07418918d90f247a1

Fixes: b9080324d6ca ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508939/
Link: https://lore.kernel.org/r/20221026182824.876933-7-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Appropriately set dsc->mux_word_size based on bpc

This field is currently unread but will come into effect when duplicated
code below is migrated to call drm_dsc_compute_rc_parameters(), which
uses the bpc-dependent value of the local variable mux_words_size in
much the same way.

The hardcoded constant seems to be a remnant from the `/* bpc 8 */`
comment right above, indicating that this group of field assignments is
applicable to bpc = 8 exclusively and should probably bail out on
different bpc values, until constants for other bpc values are added (or
the current ones are confirmed to be correct across multiple bpc's).

Fixes: b9080324d6ca ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508943/
Link: https://lore.kernel.org/r/20221026182824.876933-6-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Reuse earlier computed dsc->slice_chunk_size

dsi_populate_dsc_params() is called prior to dsi_update_dsc_timing() and
already computes a value for slice_chunk_size, whose value doesn't need
to be recomputed and re-set here.

Fixes: 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508934/
Link: https://lore.kernel.org/r/20221026182824.876933-5-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Use DIV_ROUND_UP instead of conditional increment on modulo

This exact same math is used to compute bytes_in_slice above in
dsi_update_dsc_timing(), also used to fill slice_chunk_size.

Fixes: b9080324d6ca ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508935/
Link: https://lore.kernel.org/r/20221026182824.876933-4-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Remove repeated calculation of slice_per_intf

slice_per_intf is already computed for intf_width, which holds the same
value as hdisplay.

Fixes: 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508933/
Link: https://lore.kernel.org/r/20221026182824.876933-3-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Remove useless math in DSC calculations

Multiplying a value by 2 and adding 1 to it always results in a value
that is uneven, and that 1 gets truncated immediately when performing
integer division by 2 again.  There is no "rounding" possible here.

After that target_bpp_x16 is used to store a multiplication of
bits_per_pixel by 16 which is only ever read to immediately be divided
by 16 again, and is elided in much the same way.

Fixes: b9080324d6ca ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508932/
Link: https://lore.kernel.org/r/20221026182824.876933-2-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: Add phy configuration for QCM2290

The QCM2290 SoC a the 14nm (V2.0) single DSI phy. The platform is not
fully compatible with the standard 14nm PHY, so it requires a separate
compatible and config entry.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[DB: rebased and updated commit msg]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/504578/
Link: https://lore.kernel.org/r/20220924121900.222711-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: Add QCM2290 DSI phy

QCM2290 platform uses the 14nm DSI PHY driver.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/504579/
Link: https://lore.kernel.org/r/20220924121900.222711-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dsi: drop modeset sanity checks

Drop the overly defensive modeset sanity checks of function parameters
which have already been checked or used by the callers.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502678/
Link: https://lore.kernel.org/r/20220913085320.8577-11-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu1: Account for DSC's bits_per_pixel having 4 fractional bits

According to the comment this DPU register contains the bits per pixel
as a 6.4 fractional value, conveniently matching the contents of
bits_per_pixel in struct drm_dsc_config which also uses 4 fractional
bits.  However, the downstream source this implementation was
copy-pasted from has its bpp field stored _without_ fractional part.

This makes the entire convoluted math obsolete as it is impossible to
pull those 4 fractional bits out of thin air, by somehow trying to reuse
the lowest 2 bits of a non-fractional bpp (lsb = bpp % 4??).

The rest of the code merely attempts to keep the integer part a multiple
of 4, which is rendered useless thanks to data |= dsc->bits_per_pixel <<
12; already filling up those bits anyway (but not on downstream).

Fixes: c110cfd1753e ("drm/msm/disp/dpu1: Add support for DSC")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/508946/
Link: https://lore.kernel.org/r/20221026182824.876933-10-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dp: drop modeset sanity checks

Drop the overly defensive modeset sanity checks of function parameters
which have already been checked or used by the callers.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502674/
Link: https://lore.kernel.org/r/20220913085320.8577-10-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/hdmi: move msm_hdmi_get_phy() to msm_hdmi_dev_probe()

To continue the idea of failing the probe() rather than failing the
bind(), move the call to msm_hdmi_get_phy() function to
msm_hdmi_dev_probe(), so that the driver fails the probe if PHY is not
yet available rather than succeeding the probe and then failing the
bind() with -EPROBE_DEFER.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499652/
Link: https://lore.kernel.org/r/20220826093927.851597-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/hdmi: don't take extra reference on PHY device

The of_find_device_by_node() already increments the device's usage
count, so there is no need to increment it again using get_device().
Drop this extra get_device().

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499648/
Link: https://lore.kernel.org/r/20220826093927.851597-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/hdmi: move resource allocation to probe function

Rather than having all resource allocation happen in the _bind function
(resulting in possible EPROBE_DEFER returns and component bind/unbind
cycles) allocate and check all resources in _probe function. While we
are at it, use platform_get_irq() to get the IRQ rather than going
through the irq_of_parse_and_map().

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499649/
Link: https://lore.kernel.org/r/20220826093927.851597-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: remove duplicated code from a6xx_create_address_space

The function a6xx_create_address_space() is mostly a copy of
adreno_iommu_create_address_space() with added quirk setting. Rework
these two functions to be a thin wrappers around a common helper.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/509614/
Link: https://lore.kernel.org/r/20221102175449.452283-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: move domain allocation into msm_iommu_new()

After the msm_iommu instance is created, the IOMMU domain is completely
handled inside the msm_iommu code. Move the iommu_domain_alloc() call
into the msm_iommu_new() to simplify callers code.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/509615/
Link: https://lore.kernel.org/r/20221102175449.452283-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/hdmi: drop constant resource names from platform config

All MSM HDMI devices use "core_physical" and "qfprom_physical" names for
register areas. Drop them from the platform config.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499646/
Link: https://lore.kernel.org/r/20220826093927.851597-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/hdmi: use devres helper for runtime PM management

Use devm_pm_runtime_enable() to enable runtime PM. This way its effect
will be reverted on device unbind/destruction.

Fixes: 6ed9ed484d04 ("drm/msm/hdmi: Set up runtime PM for HDMI")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499647/
Link: https://lore.kernel.org/r/20220826093927.851597-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Refactor sc7280_pp location

The sc7280_pp declaration is not located by the other _pp
declarations, but rather hidden around the _merge_3d
declarations. Let's fix this to avoid confusion.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/509153/
Link: https://lore.kernel.org/r/20221028120812.339100-3-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: add support for the display on SM8250

Add DPU and MDSS schemas to describe MDSS and DPU blocks on the Qualcomm
SM8250 platform.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508397/
Link: https://lore.kernel.org/r/20221024164225.3236654-13-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: add missing device nodes to mdss-* schemas

Add missing device nodes (DSI, PHYs, DP/eDP) to the existing MDSS
schemas.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508391/
Link: https://lore.kernel.org/r/20221024164225.3236654-12-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: split dpu-qcm2290 into DPU and MDSS parts

In order to make the schema more readable, split dpu-qcm2290 into the DPU
and MDSS parts, each one describing just a single device binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508383/
Link: https://lore.kernel.org/r/20221024164225.3236654-11-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: split dpu-msm8998 into DPU and MDSS parts

In order to make the schema more readable, split dpu-msm8998 into the DPU
and MDSS parts, each one describing just a single device binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508388/
Link: https://lore.kernel.org/r/20221024164225.3236654-10-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: split dpu-sdm845 into DPU and MDSS parts

In order to make the schema more readable, split dpu-sdm845 into the DPU
and MDSS parts, each one describing just a single device binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508382/
Link: https://lore.kernel.org/r/20221024164225.3236654-9-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: split dpu-sc7280 into DPU and MDSS parts

In order to make the schema more readable, split dpu-sc7280 into the DPU
and MDSS parts, each one describing just a single device binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508387/
Link: https://lore.kernel.org/r/20221024164225.3236654-8-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: split dpu-sc7180 into DPU and MDSS parts

In order to make the schema more readable, split dpu-sc7180 into the DPU
and MDSS parts, each one describing just a single device binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508386/
Link: https://lore.kernel.org/r/20221024164225.3236654-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: move common MDSS properties to mdss-common.yaml

Move properties common to all MDSS DT nodes to the mdss-common.yaml.

This extends qcom,msm8998-mdss schema to allow interconnect nodes, which
will be added later, once msm8998 gains interconnect support.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508385/
Link: https://lore.kernel.org/r/20221024164225.3236654-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: move common DPU properties to dpu-common.yaml

Move properties common to all DPU DT nodes to the dpu-common.yaml.

Note, this removes description of individual DPU port@ nodes. However
such definitions add no additional value. The reg values do not
correspond to hardware INTF indices. The driver discovers and binds
these ports not paying any care for the order of these items. Thus just
leave the reference to graph.yaml#/properties/ports and the description.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508384/
Link: https://lore.kernel.org/r/20221024164225.3236654-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: add interconnects property to qcom, mdss-smd845

Add interconnects required for the SDM845 MDSS device tree node. This
change was made in the commit c8c61c09e38b ("arm64: dts: qcom: sdm845:
Add interconnects property for display"), but was not reflected in the
schema.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508380/
Link: https://lore.kernel.org/r/20221024164225.3236654-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: add gcc-bus clock to dpu-smd845

Add gcc-bus clock required for the SDM845 DPU device tree node. This
change was made in the commit 111c52854102 ("arm64: dts: qcom: sdm845:
move bus clock to mdp node for sdm845 target"), but was not reflected in
the schema.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508379/
Link: https://lore.kernel.org/r/20221024164225.3236654-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

dt-bindings: display/msm: split qcom, mdss bindings

Split Mobile Display SubSystem (MDSS) root node bindings to the separate
yaml file. Changes to the existing (txt) schema:
 - Added optional "vbif_nrt_phys" region used by msm8996
 - Made "bus" and "vsync" clocks optional (they are not used by some
   platforms)
 - Added optional resets property referencing MDSS reset
 - Defined child nodes pointing to corresponding reference schema.
 - Dropped the "lut" clock. It was added to the schema by mistake (it is
   a part of mdp4 schema, not the mdss).

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508378/
Link: https://lore.kernel.org/r/20221024164225.3236654-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: Add MSM_INFO_GET_FLAGS

In some cases crosvm needs a way to query the cache flags to communicate
them to the guest kernel for guest userspace mapping.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/504453/
Link: https://lore.kernel.org/r/20220923173307.2429872-1-robdclark@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: use DEFINE_SHOW_ATTRIBUTE to simplify dpu_regset32

Use DEFINE_SHOW_ATTRIBUTE helper macro to simplify the code.
No functional change.

Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/504252/
Link: https://lore.kernel.org/r/20220922142147.3246649-1-liushixin2@huawei.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/mdp5: stop overriding drvdata

The rest of the code expects that master's device drvdata is the
struct msm_drm_private instance. Do not override the mdp5's drvdata.

Fixes: 6874f48bb8b0 ("drm/msm: make mdp5/dpu devices master components")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/508334/
Link: https://lore.kernel.org/r/20221024152642.3213488-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dp: retry 3 times if set sink to D0 poweer state failed

Bring sink out of D3 (power down) mode into D0 (normal operation) mode
by setting DP_SET_POWER_D0 bit to DP_SET_POWER dpcd register. This
patch will retry 3 times if written to DP_SET_POWER register failed.

Changes in v5:
-- split into two patches

Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502536/
Link: https://lore.kernel.org/r/1662999830-13916-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Add support for P010 format

Add support for P010 color format. This adds support for both linear and
compressed formats.

Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/500822/
Link: https://lore.kernel.org/r/20220901203422.217-3-quic_jesszhan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dp: replace variable err with len at dp_aux_link_power_up()

drm_dp_dpcd_readb() will return 1 to indicate one byte had been read
successfully. This patch replace variable "err" with "len" have more
correct meaning.

changes in v5:
-- split into 3 patches

Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/502533/
Link: https://lore.kernel.org/r/1662999830-13916-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm/dpu: Add support for XR30 format

Add support for XR30 color format. This supports both linear and
compressed formats.

Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/500820/
Link: https://lore.kernel.org/r/20220901203422.217-2-quic_jesszhan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/msm: less magic numbers in msm_mdss_enable

Replace magic register writes in msm_mdss_enable() with version that
contains less magic and more variable names that can be traced back to
the dpu_hw_catalog or the downstream dtsi files.

Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/489578/
Link: https://lore.kernel.org/r/20220615135935.87381-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

Merge remote-tracking branch 'msm/msm-fixes' into HEAD

Merge tag 'drm-next-20221025' of git://linuxtv.org/pinchartl/media into drm-next

Xilinx ZynqMP DisplayPort bridge support

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y1cdU4HJoy0Pr2sQ@pendragon.ideasonboard.com

drm/nouveau: Remove unused variable

Trivial removal of an unused variable. Not sure how it snuck by me and
build bots in the 7c99616e3fe7.

Fixes: 7c99616e3fe7 ("drm: Remove drm_mode_config::fb_base")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Thomas Zimmermann <tzimemrmann@suse.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221021010703.536318-1-zack@kde.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge tag 'drm-misc-next-2022-10-20' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

drm-misc-next for 6.2:

UAPI Changes:
  - Documentation for page-flip flags

Cross-subsystem Changes:
  - dma-buf: Add unlocked variant of vmapping and attachment-mapping
    functions

Core Changes:
  - atomic-helpers: CRTC primary plane test fixes
  - connector: TV API consistency improvements, cmdline parsing
    improvements
  - crtc-helpers: Introduce drm_crtc_helper_atomic_check() helper
  - edid: Fixes for HFVSDB parsing,
  - fourcc: Addition of the Vivante tiled modifier
  - makefile: Sort and reorganize the objects files
  - mode_config: Remove fb_base from drm_mode_config_funcs
  - sched: Add a module parameter to change the scheduling policy,
    refcounting fix for fences
  - tests: Sort the Kunit tests in the Makefile, improvements to the
    DP-MST tests
  - ttm: Remove unnecessary drm_mm_clean() call

Driver Changes:
  - New driver: ofdrm
  - Move all drivers to a common dma-buf locking convention
  - bridge:
    - adv7533: Remove dynamic lane switching
    - it6505: Runtime PM support
    - ps8640: Handle AUX defer messages
    - tc358775: Drop soft-reset over I2C
  - ast: Atomic Gamma LUT Support, Convert to SHMEM, various
    improvements
  - lcdif: Support for YUV planes
  - mgag200: Fix PLL Setup on some revisions
  - udl: Modesetting improvements, hot-unplug support
  - vc4: Fix support for PAL-M

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020072405.g3o4hxuk75gmeumw@houat

Linux 6.1-rc2

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull kvm fixes from Paolo Bonzini:
 "RISC-V:

   - Fix compilation without RISCV_ISA_ZICBOM

   - Fix kvm_riscv_vcpu_timer_pending() for Sstc

  ARM:

   - Fix a bug preventing restoring an ITS containing mappings for very
     large and very sparse device topology

   - Work around a relocation handling error when compiling the nVHE
     object with profile optimisation

   - Fix for stage-2 invalidation holding the VM MMU lock for too long
     by limiting the walk to the largest block mapping size

   - Enable stack protection and branch profiling for VHE

   - Two selftest fixes

  x86:

   - add compat implementation for KVM_X86_SET_MSR_FILTER ioctl

  selftests:

   - synchronize includes between include/uapi and tools/include/uapi"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  tools: include: sync include/api/linux/kvm.h
  KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
  KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
  kvm: Add support for arch compat vm ioctls
  RISC-V: KVM: Fix kvm_riscv_vcpu_timer_pending() for Sstc
  RISC-V: Fix compilation without RISCV_ISA_ZICBOM
  KVM: arm64: vgic: Fix exit condition in scan_its_table()
  KVM: arm64: nvhe: Fix build with profile optimization
  KVM: selftests: Fix number of pages for memory slot in memslot_modification_stress_test
  KVM: arm64: selftests: Fix multiple versions of GIC creation
  KVM: arm64: Enable stack protection and branch profiling for VHE
  KVM: arm64: Limit stage2_apply_range() batch size to largest block
  KVM: arm64: Work out supported block level at compile time

Revert "mfd: syscon: Remove repetition of the regmap_get_val_endian()"

This reverts commit 72a95859728a7866522e6633818bebc1c2519b17.

It broke reboots on big-endian MIPS and MIPS64 malta QEMU instances,
which use the syscon driver.  Little-endian is not effected, which means
likely it's important to handle regmap_get_val_endian() in this function
after all.

Fixes: 72a95859728a ("mfd: syscon: Remove repetition of the regmap_get_val_endian()")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/utsname_sysctl.c: Fix hostname polling

Commit bfca3dd3d068 ("kernel/utsname_sysctl.c: print kernel arch") added
a new entry to the uts_kern_table[] array, but didn't update the
UTS_PROC_xyz enumerators of older entries, breaking anything that used
them.

Which is admittedly not many cases: it's really just the two uses of
uts_proc_notify() in kernel/sys.c.  But apparently journald-systemd
actually uses this to detect hostname changes.

Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Fixes: bfca3dd3d068 ("kernel/utsname_sysctl.c: print kernel arch")
Link: https://lore.kernel.org/lkml/0c2b92a6-0f25-9538-178f-eee3b06da23f@secunet.com/
Link: https://linux-regtracking.leemhuis.info/regzbot/regression/0c2b92a6-0f25-9538-178f-eee3b06da23f@secunet.com/
Cc: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'perf_urgent_for_v6.1_rc2' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Borislav Petkov:

 - Fix raw data handling when perf events are used in bpf

 - Rework how SIGTRAPs get delivered to events to address a bunch of
   problems with it. Add a selftest for that too

* tag 'perf_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  bpf: Fix sample_flags for bpf_perf_event_output
  selftests/perf_events: Add a SIGTRAP stress test with disables
  perf: Fix missing SIGTRAPs

Merge tag 'sched_urgent_for_v6.1_rc2' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Borislav Petkov:

 - Adjust code to not trip up CFI

 - Fix sched group cookie matching

* tag 'sched_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Introduce struct balance_callback to avoid CFI mismatches
  sched/core: Fix comparison in sched_group_cookie_match()

Merge tag 'objtool_urgent_for_v6.1_rc2' of git://git./linux/kernel/git/tip/tip

Pull objtool fix from Borislav Petkov:

 - Fix ORC stack unwinding when GCOV is enabled

* tag 'objtool_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/unwind/orc: Fix unreliable stack dump with gcov

Merge tag 'x86_urgent_for_v6.0_rc2' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Borislav Petkov:
 "As usually the case, right after a major release, the tip urgent
  branches accumulate a couple more fixes than normal. And here is the
  x86, a bit bigger, urgent pile.

   - Use the correct CPU capability clearing function on the error path
     in Intel perf LBR

   - A CFI fix to ftrace along with a simplification

   - Adjust handling of zero capacity bit mask for resctrl cache
     allocation on AMD

   - A fix to the AMD microcode loader to attempt patch application on
     every logical thread

   - A couple of topology fixes to handle CPUID leaf 0x1f enumeration
     info properly

   - Drop a -mabi=ms compiler option check as both compilers support it
     now anyway

   - A couple of fixes to how the initial, statically allocated FPU
     buffer state is setup and its interaction with dynamic states at
     runtime"

* tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu: Fix copy_xstate_to_uabi() to copy init states correctly
  perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
  ftrace,kcfi: Separate ftrace_stub() and ftrace_stub_graph()
  x86/ftrace: Remove ftrace_epilogue()
  x86/resctrl: Fix min_cbm_bits for AMD
  x86/microcode/AMD: Apply the patch early on every logical thread
  x86/topology: Fix duplicated core ID within a package
  x86/topology: Fix multiple packages shown on a single-package system
  hwmon/coretemp: Handle large core ID value
  x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
  x86/fpu: Exclude dynamic states from init_fpstate
  x86/fpu: Fix the init_fpstate size check with the actual size
  x86/fpu: Configure init_fpstate attributes orderly

Merge tag 'io_uring-6.1-2022-10-22' of git://git.kernel.dk/linux

Pull io_uring follow-up from Jens Axboe:
 "Currently the zero-copy has automatic fallback to normal transmit, and
  it was decided that it'd be cleaner to return an error instead if the
  socket type doesn't support it.

  Zero-copy does work with UDP and TCP, it's more of a future proofing
  kind of thing (eg for samba)"

* tag 'io_uring-6.1-2022-10-22' of git://git.kernel.dk/linux:
  io_uring/net: fail zc sendmsg when unsupported by socket
  io_uring/net: fail zc send when unsupported by socket
  net: flag sockets supporting msghdr originated zerocopy