scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged

Commit 5ff843721467 ("scsi: virtio_scsi: unplug LUNs when events missed")
missed a corner case in which all the LUNs are unplugged at the same time.

In this case INQUIRY returns DID_BAD_TARGET. Detect this and unplug the
LUN.

Link: https://lore.kernel.org/r/20200729194806.4933-2-mlevitsk@redhat.com
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_debug: Implement tur_ms_to_ready parameter

The current driver responds to TEST UNIT READY (TUR) with a GOOD status
immediately after a scsi_debug device (LU) is created. This is unrealistic
as even SSDs take some time after power-on before accepting media access
commands.

Add the tur_ms_to_ready parameter whose unit is milliseconds (default 0)
and is the period before which a TUR (or any media access command) will set
the CHECK CONDITION status with a sense key of NOT READY and an additional
sense of "Logical unit is in process of becoming ready".  The period starts
when each scsi_debug device is created.

This patch was prompted by T10 proposal 20-061r2 which was accepted on
2020716. It adds that a TUR in the situation described in the previous
paragraph may set the INFO field (or descriptor) in the sense data to the
estimated number in milliseconds before a subsequent TUR will yield a GOOD
status. This patch follows that advice.

Link: https://lore.kernel.org/r/20200724155531.668144-1-dgilbert@interlog.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: scsi_debug: Fix request sense

The SCSI REQUEST SENSE command emulation was found to be broken.  It is a
quite complex command so try and make it do a subset of what it should
do. Remove the attempt to mimic SCSI-1 REQUEST SENSE (i.e. return the sense
data for the previous failed command). Add some reporting of "pollable"
sense data [see spc6r02: 5.12.2]. Keep the IEC mode page MRIE=6 TEST=1
predictive failure reporting.

Link: https://lore.kernel.org/r/20200723194819.545573-1-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix typo in comment for ULP

UPL -> ULP for "Upper Layer Protocol"

Link: https://lore.kernel.org/r/20200728145606.1601726-1-ferruh.yigit@intel.com
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC

In some platforms, VCC regulator may not be declared in device tree to keep
itself "always-on". In this case, hba->vreg_info.vcc is NULL and shall not
be operated during any flow.

Prevent possible NULL hba->vreg_info.vcc access in LPM mode by checking
if it is valid first.

Link: https://lore.kernel.org/r/20200724141627.20094-1-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: iscsi: Do not put host in iscsi_set_flashnode_param()

If scsi_host_lookup() fails we will jump to put_host which may cause a
panic. Jump to exit_set_fnode instead.

Link: https://lore.kernel.org/r/20200615081226.183068-1-jingxiangfeng@huawei.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: hpsa: Correct ctrl queue depth

Need to set queue depth for controller devices.

Link: https://lore.kernel.org/r/159562590819.17915.12766718094041027754.stgit@brunhilda
Fixes: 30bda7848a23 ("scsi: hpsa: Increase controller error handling timeout")
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: tcmu: Make TMR notification optional

Add "tmr_notification" configfs attribute to tcmu devices.  If the default
value 0 is used, tcmu only removes aborted commands from qfull_queue.  If
user changes tmr_notification to 1, additionally TMR notifications will be
written to the cmd ring.

Link: https://lore.kernel.org/r/20200726153510.13077-9-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: tcmu: Implement tmr_notify callback

This patch implements the tmr_notify callback for tcmu.  When the callback
is called, tcmu checks the list of aborted commands it received as
parameter:

 - aborted commands in the qfull_queue are removed from the queue and
   target_complete_command is called

 - from the cmd_ids of aborted commands currently uncompleted in cmd ring
   it creates a list of aborted cmd_ids.

Finally a TMR notification is written to cmd ring containing TMR type and
cmd_id list. If there is no space in ring, the TMR notification is queued
on a TMR specific queue.

The TMR specific queue 'tmr_queue' can be seen as a extension of the cmd
ring. At the end of each iexecution of tcmu_complete_commands() we check
whether tmr_queue contains TMRs and try to move them onto the ring. If
tmr_queue is not empty after that, we don't call run_qfull_queue() because
commands must not overtake TMRs.

This way we guarantee that cmd_ids in TMR notification received by
userspace either match an active, not yet completed command or are no
longer valid due to userspace having complete some cmd_ids meanwhile.

New commands that were assigned to an aborted cmd_id will always appear on
the cmd ring _after_ the TMR.

Link: https://lore.kernel.org/r/20200726153510.13077-8-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: tcmu: Fix and simplify timeout handling

During cmd timeout handling in check_timedout_devices(), due to a race, it
can happen that tcmu_set_next_deadline() does not start a timer as
expected:

 1) Either tcmu_check_expired_ring_cmd() checks the inflight_queue or
    tcmu_check_expired_queue_cmd() checks the qfull_queue while jiffies has
    the value X

 2) At the end of the check the queue contains one remaining command with
    deadline X (time_after(X, X) is false and thus the command is not
    handled as being timed out).

 3) After tcmu_check_expired_xxxxx_cmd() a timer interrupt happens and
    jiffies is incremented to X+1.

 4) Now tcmu_set_next_deadline() is called, but it skips the command, since
    time_after(X+1, X) is true. Therefore tcmu_set_next_deadline() finds no
    new deadline and stops the timer, which it shouldn't.

Since commands that time out are removed from inflight_queue or
qfull_queue, we don't need the check with time_after() in
tcmu_set_next_deadline() but can use the deadline from the first cmd in
the queue.

Additionally, replace the remaining time_after() calls in
tcmu_check_expired_xxxxx_cmd() with time_after_eq(), because it is not
useful to set the timeout to deadline but then check for jiffies being
greater than deadline.

Simplify the end of tcmu_handle_completions() and change the check for no
more pending commands from

mb->cmd_tail == mb->cmd_head
to

idr_is_empty(&udev->commands)

because the old check doesn't work correctly if paddings or in the future
TMRs are in the ring.

Finally tcmu_set_next_deadline() was shifted in the source as
preparation for later implementation of tmr_notify callback.

Link: https://lore.kernel.org/r/20200726153510.13077-7-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: tcmu: Factor out new helper ring_insert_padding

The new helper ring_insert_padding is split off from and then called by
queue_cmd_ring. It inserts a padding if necessary.  The new helper will in
a subsequent patch be used during writing of TMR notifications to command
ring.

Link: https://lore.kernel.org/r/20200726153510.13077-6-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: tcmu: Do not queue aborted commands

If tcmu receives an already aborted command, tcmu_queue_cmd() should reject
it.

Link: https://lore.kernel.org/r/20200726153510.13077-5-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: tcmu: Use priv pointer in se_cmd

We initialize and clean up the se_cmd's priv pointer under cmd_ring_lock to
point to the corresponding tcmu_cmd.

In the patch that implements tmr_notify callback in tcmu we will use the
priv pointer.

Link: https://lore.kernel.org/r/20200726153510.13077-4-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: Add tmr_notify backend function

Target core is modified to call an optional backend callback function if a
TMR is received or commands are aborted implicitly after a PR command was
received.  The backend function takes as parameters the se_dev, the type of
the TMR, and the list of aborted commands.  If no commands were aborted, an
empty list is supplied.

Link: https://lore.kernel.org/r/20200726153510.13077-3-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: Modify core_tmr_abort_task()

This patch modifies core_tmr_abort_task() to use same looping and locking
scheme as core_tmr_drain_state_list() does.

This frees the state_list element in se_cmd for later use by tmr
notification handling.

Note: __target_check_io_state() now is called with param 0 instead of
dev->dev_attrib.emulate_tas, because tas is not relevant since we always
get ABRT on same session like the aborted command.

Link: https://lore.kernel.org/r/20200726153510.13077-2-bstroesser@ts.fujitsu.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: iscsi: Fix inconsistent debug message

Commit 25cdda95fda7 ("iscsi-target: Fix initial login PDU asynchronous
socket close OOPs") changed the return value of
__iscsi_target_sk_check_close(). However, pr_debug is still printing FALSE
when returning TRUE which is a little confusing.

Link: https://lore.kernel.org/r/20200716100212.4237-3-houpu@bytedance.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Hou Pu <houpu@bytedance.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: iscsi: Fix login error when receiving

iscsi_target_sk_data_ready() could be invoked indirectly by
iscsi_target_do_login_rx() from the workqueue like this:

iscsi_target_do_login_rx()
  iscsi_target_do_login()
    iscsi_target_do_tx_login_io()
      iscsit_put_login_tx()
        iscsi_login_tx_data()
          tx_data()
            sock_sendmsg_nosec()
              tcp_sendmsg()
                release_sock()
                  sk_backlog_rcv()
                    tcp_v4_do_rcv()
                      tcp_data_ready()
                        iscsi_target_sk_data_ready()

At that time LOGIN_FLAGS_READ_ACTIVE is not cleared and
iscsi_target_sk_data_ready will not read data from the socket. Some iscsi
initiators (libiscsi) will wait forever for a reply.

LOGIN_FLAGS_READ_ACTIVE should be cleared early just after doing the
receive and before writing to the socket in iscsi_target_do_login_rx.

Unfortunately, LOGIN_FLAGS_READ_ACTIVE is also used by sk_state_change to
do login cleanup if a socket was closed at login time. It is supposed to be
cleared after the login PDU is successfully processed and replied.

Introduce another flag, LOGIN_FLAGS_WRITE_ACTIVE, to cover the transmit
part.

Link: https://lore.kernel.org/r/20200716100212.4237-2-houpu@bytedance.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Hou Pu <houpu@bytedance.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: mvsas: Move 'core_nr' inside #ifdef and remove unused variable 'res_flag'

Only declare 'core_nr' if its conditions for use are met.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/mvsas/mv_init.c: In function ‘mvs_interrupt’:
 drivers/scsi/mvsas/mv_init.c:180:6: warning: variable ‘core_nr’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/mvsas/mv_init.c: In function ‘mvs_ioremap’:
 drivers/scsi/mvsas/mv_init.c:302:36: warning: variable ‘res_flag’ set but not used [-Wunused-but-set-variable]

[mkp: applied follow-up fixup patch]

Link: https://lore.kernel.org/r/20200721164148.2617584-40-lee.jones@linaro.org
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Marvell <kewei@marvell.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: esas2r: Demote a few non-conformant kerneldoc headers

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/esas2r/esas2r_log.c:86: warning: Function parameter or member 'level' not described in 'translate_esas2r_event_level_to_kernel'
 drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'level' not described in 'esas2r_log_master'
 drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'dev' not described in 'esas2r_log_master'
 drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'format' not described in 'esas2r_log_master'
 drivers/scsi/esas2r/esas2r_log.c:120: warning: Function parameter or member 'args' not described in 'esas2r_log_master'
 drivers/scsi/esas2r/esas2r_log.c:183: warning: Function parameter or member 'level' not described in 'esas2r_log'
 drivers/scsi/esas2r/esas2r_log.c:183: warning: Function parameter or member 'format' not described in 'esas2r_log'
 drivers/scsi/esas2r/esas2r_log.c:211: warning: Function parameter or member 'level' not described in 'esas2r_log_dev'
 drivers/scsi/esas2r/esas2r_log.c:211: warning: Function parameter or member 'dev' not described in 'esas2r_log_dev'
 drivers/scsi/esas2r/esas2r_log.c:211: warning: Function parameter or member 'format' not described in 'esas2r_log_dev'
 drivers/scsi/esas2r/esas2r_log.c:237: warning: Function parameter or member 'level' not described in 'esas2r_log_hexdump'
 drivers/scsi/esas2r/esas2r_log.c:237: warning: Function parameter or member 'buf' not described in 'esas2r_log_hexdump'
 drivers/scsi/esas2r/esas2r_log.c:237: warning: Function parameter or member 'len' not described in 'esas2r_log_hexdump'

Link: https://lore.kernel.org/r/20200723122446.1329773-41-lee.jones@linaro.org
Cc: Bradley Grove <linuxdrivers@attotech.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bnx2i: Add parameter description and rename another

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bnx2i/bnx2i_iscsi.c:1288: warning: Function parameter or member 'cmds_max' not described in 'bnx2i_session_create'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:2176: warning: Function parameter or member 'params' not described in 'bnx2i_nl_set_path'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:2176: warning: Excess function parameter 'buf' description in 'bnx2i_nl_set_path'

Link: https://lore.kernel.org/r/20200723122446.1329773-40-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Ensure a blank line precedes next function/header

Fixes the following checkpatch warning:

 CHECK: Please use a blank line after function/struct/union/enum declarations
 #129: FILE: drivers/scsi/bfa/bfa_ioc.c:6913:
  }
 +/*

Link: https://lore.kernel.org/r/20200723122446.1329773-39-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: Staticify non-external function 'qedi_get_iscsi_error'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qedi/qedi_iscsi.c:1549:7: warning: no previous prototype for ‘qedi_get_iscsi_error’ [-Wmissing-prototypes]

Link: https://lore.kernel.org/r/20200723122446.1329773-38-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: Demote seemingly unintentional kerneldoc header

This is the only use of kerneldoc in the source file and no descriptions
are provided.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qedi/qedi_main.c:1969: warning: Function parameter or member 'qedi' not described in 'qedi_get_nvram_block'

Link: https://lore.kernel.org/r/20200723122446.1329773-37-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Demote seemingly unintentional kerneldoc header

This is the only use of kerneldoc in the source file and no descriptions
are provided.

Also demote standard comment.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_svc.c:3847: warning: Function parameter or member 'bfa' not described in 'bfa_fcport_get_cfg_topology'

Link: https://lore.kernel.org/r/20200723122446.1329773-36-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Demote seemingly unintentional kerneldoc header

This is the only use of kerneldoc in the source file and no
descriptions are provided.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_core.c:1245: warning: Function parameter or member 'bfa' not described in 'bfa_iocfc_qreg'
 drivers/scsi/bfa/bfa_core.c:1245: warning: Function parameter or member 'qreg' not described in 'bfa_iocfc_qreg'

Link: https://lore.kernel.org/r/20200723122446.1329773-35-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Demote non-kerneldoc headers down to standard comment blocks

This is probably historical (Doxygen?).

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_ioc.c:6646: warning: Cannot understand  * @brief hardware error definition
 drivers/scsi/bfa/bfa_ioc.c:6661: warning: Cannot understand  * @brief flash command register data structure
 drivers/scsi/bfa/bfa_ioc.c:6685: warning: Cannot understand  * @brief flash device status register data structure
 drivers/scsi/bfa/bfa_ioc.c:6711: warning: Cannot understand  * @brief flash address register data structure
 drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'pci_bar' not described in 'bfa_flash_set_cmd'
 drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'wr_cnt' not described in 'bfa_flash_set_cmd'
 drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'rd_cnt' not described in 'bfa_flash_set_cmd'
 drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'ad_cnt' not described in 'bfa_flash_set_cmd'
 drivers/scsi/bfa/bfa_ioc.c:6732: warning: Function parameter or member 'op' not described in 'bfa_flash_set_cmd'
 drivers/scsi/bfa/bfa_ioc.c:6768: warning: Cannot understand  * @brief
 drivers/scsi/bfa/bfa_ioc.c:6807: warning: Cannot understand  * @brief
 drivers/scsi/bfa/bfa_ioc.c:6852: warning: Cannot understand  * @brief
 drivers/scsi/bfa/bfa_ioc.c:6898: warning: Cannot understand  * @brief
 drivers/scsi/bfa/bfa_ioc.c:6914: warning: Cannot understand  * @brief
 drivers/scsi/bfa/bfa_ioc.c:6940: warning: Cannot understand  * @brief

Link: https://lore.kernel.org/r/20200723122446.1329773-34-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: esas2r: Add braces around the one-line if()

In certain configurations esas2r_bugon() is sometimes NULLed by the compiler.

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/scsi/esas2r/esas2r_log.c:44:
 drivers/scsi/esas2r/esas2r.h: In function ‘esas2r_rq_init_request’:
 drivers/scsi/esas2r/esas2r.h:1229:17: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
 1229 | esas2r_bugon();
 | ^
 NB: Lots of these - snipped for brevity

Link: https://lore.kernel.org/r/20200723122446.1329773-33-lee.jones@linaro.org
Cc: Bradley Grove <linuxdrivers@attotech.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: Remove set but unused variable 'tmp'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qedi/qedi_fw.c: In function ‘qedi_put_rq_bdq_buf’:
 drivers/scsi/qedi/qedi_fw.c:355:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]

Link: https://lore.kernel.org/r/20200723122446.1329773-32-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: be2iscsi: Correct misdocumentation of function param 'ep'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/be2iscsi/be_iscsi.c:1042: warning: Function parameter or member 'ep' not described in 'beiscsi_open_conn'
 drivers/scsi/be2iscsi/be_iscsi.c:1042: warning: Excess function parameter 'beiscsi_ep' description in 'beiscsi_open_conn'

Link: https://lore.kernel.org/r/20200723122446.1329773-31-lee.jones@linaro.org
Cc: Subbu Seetharaman <subbu.seetharaman@broadcom.com>
Cc: Ketan Mukadam <ketan.mukadam@broadcom.com>
Cc: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: linux-drivers@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bnx2i: Add, remove and edit some function parameter descriptions

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bnx2i/bnx2i_iscsi.c:241: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_bind_conn_to_iscsi_cid'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:241: warning: Excess function parameter 'conn' description in 'bnx2i_bind_conn_to_iscsi_cid'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:470: warning: Excess function parameter 'cmd' description in 'bnx2i_destroy_cmd_pool'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:595: warning: Function parameter or member 'cls_session' not described in 'bnx2i_drop_session'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:595: warning: Excess function parameter 'hba' description in 'bnx2i_drop_session'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:595: warning: Excess function parameter 'session' description in 'bnx2i_drop_session'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:1290: warning: Function parameter or member 'ep' not described in 'bnx2i_session_create'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:1979: warning: Function parameter or member 'bnx2i_ep' not described in 'bnx2i_ep_tcp_conn_active'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:1979: warning: Excess function parameter 'ep' description in 'bnx2i_ep_tcp_conn_active'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:2178: warning: Function parameter or member 'shost' not described in 'bnx2i_nl_set_path'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:2178: warning: Function parameter or member 'params' not described in 'bnx2i_nl_set_path'
 drivers/scsi/bnx2i/bnx2i_iscsi.c:2178: warning: Excess function parameter 'buf' description in 'bnx2i_nl_set_path'

Link: https://lore.kernel.org/r/20200723122446.1329773-30-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bnx2i: Fix a whole host of kerneldoc issues

Mainly renames and docrot issues.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bnx2i/bnx2i_hwi.c:194: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_get_rq_buf'
 drivers/scsi/bnx2i/bnx2i_hwi.c:194: warning: Excess function parameter 'conn' description in 'bnx2i_get_rq_buf'
 drivers/scsi/bnx2i/bnx2i_hwi.c:232: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_put_rq_buf'
 drivers/scsi/bnx2i/bnx2i_hwi.c:232: warning: Excess function parameter 'conn' description in 'bnx2i_put_rq_buf'
 drivers/scsi/bnx2i/bnx2i_hwi.c:269: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_ring_sq_dbell'
 drivers/scsi/bnx2i/bnx2i_hwi.c:269: warning: Excess function parameter 'conn' description in 'bnx2i_ring_sq_dbell'
 drivers/scsi/bnx2i/bnx2i_hwi.c:293: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_ring_dbell_update_sq_params'
 drivers/scsi/bnx2i/bnx2i_hwi.c:293: warning: Excess function parameter 'conn' description in 'bnx2i_ring_dbell_update_sq_params'
 drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_login'
 drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Function parameter or member 'task' not described in 'bnx2i_send_iscsi_login'
 drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_login'
 drivers/scsi/bnx2i/bnx2i_hwi.c:331: warning: Excess function parameter 'cmd' description in 'bnx2i_send_iscsi_login'
 drivers/scsi/bnx2i/bnx2i_hwi.c:384: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_tmf'
 drivers/scsi/bnx2i/bnx2i_hwi.c:384: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_tmf'
 drivers/scsi/bnx2i/bnx2i_hwi.c:458: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_text'
 drivers/scsi/bnx2i/bnx2i_hwi.c:458: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_text'
 drivers/scsi/bnx2i/bnx2i_hwi.c:506: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_scsicmd'
 drivers/scsi/bnx2i/bnx2i_hwi.c:506: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_scsicmd'
 drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_nopout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Function parameter or member 'task' not described in 'bnx2i_send_iscsi_nopout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_nopout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:533: warning: Excess function parameter 'cmd' description in 'bnx2i_send_iscsi_nopout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_send_iscsi_logout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Function parameter or member 'task' not described in 'bnx2i_send_iscsi_logout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Excess function parameter 'conn' description in 'bnx2i_send_iscsi_logout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:590: warning: Excess function parameter 'cmd' description in 'bnx2i_send_iscsi_logout'
 drivers/scsi/bnx2i/bnx2i_hwi.c:686: warning: Function parameter or member 't' not described in 'bnx2i_ep_ofld_timer'
 drivers/scsi/bnx2i/bnx2i_hwi.c:686: warning: Excess function parameter 'data' description in 'bnx2i_ep_ofld_timer'
 drivers/scsi/bnx2i/bnx2i_hwi.c:1672: warning: Function parameter or member 'bnx2i_conn' not described in 'bnx2i_unsol_pdu_adjust_rq'
 drivers/scsi/bnx2i/bnx2i_hwi.c:1672: warning: Excess function parameter 'conn' description in 'bnx2i_unsol_pdu_adjust_rq'
 drivers/scsi/bnx2i/bnx2i_hwi.c:1900: warning: Function parameter or member 'session' not described in 'bnx2i_queue_scsi_cmd_resp'
 drivers/scsi/bnx2i/bnx2i_hwi.c:1900: warning: Function parameter or member 'cqe' not described in 'bnx2i_queue_scsi_cmd_resp'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Function parameter or member 'context' not described in 'bnx2i_indicate_kcqe'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Function parameter or member 'kcqe' not described in 'bnx2i_indicate_kcqe'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Function parameter or member 'num_cqe' not described in 'bnx2i_indicate_kcqe'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Excess function parameter 'hba' description in 'bnx2i_indicate_kcqe'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2476: warning: Excess function parameter 'update_kcqe' description in 'bnx2i_indicate_kcqe'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2624: warning: Function parameter or member 'cm_sk' not described in 'bnx2i_cm_remote_close'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2624: warning: Excess function parameter 'hba' description in 'bnx2i_cm_remote_close'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2624: warning: Excess function parameter 'update_kcqe' description in 'bnx2i_cm_remote_close'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2641: warning: Function parameter or member 'cm_sk' not described in 'bnx2i_cm_remote_abort'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2641: warning: Excess function parameter 'hba' description in 'bnx2i_cm_remote_abort'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2641: warning: Excess function parameter 'update_kcqe' description in 'bnx2i_cm_remote_abort'
 drivers/scsi/bnx2i/bnx2i_hwi.c:2677: warning: cannot understand function prototype: 'struct cnic_ulp_ops bnx2i_cnic_cb = '

Link: https://lore.kernel.org/r/20200723122446.1329773-29-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Remove unused variable 'adisc'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_fcs_rport.c: In function ‘bfa_fcs_rport_process_adisc’:
 drivers/scsi/bfa/bfa_fcs_rport.c:2243:21: warning: variable ‘adisc’ set but not used [-Wunused-but-set-variable]

Link: https://lore.kernel.org/r/20200723122446.1329773-28-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Demote non-compliant kerneldoc headers to standard comments

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_ioc_ct.c:504: warning: Function parameter or member 'ioc' not described in 'bfa_ioc_set_ctx_hwif'
 drivers/scsi/bfa/bfa_ioc_ct.c:504: warning: Function parameter or member 'hwif' not described in 'bfa_ioc_set_ctx_hwif'
 drivers/scsi/bfa/bfa_ioc_ct.c:525: warning: Function parameter or member 'ioc' not described in 'bfa_ioc_set_ct_hwif'
 drivers/scsi/bfa/bfa_ioc_ct.c:540: warning: Function parameter or member 'ioc' not described in 'bfa_ioc_set_ct2_hwif'

Link: https://lore.kernel.org/r/20200723122446.1329773-26-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: csiostor: Add missing description for csio_rnode_fwevt_handler()'s 'fwevt' param

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/csiostor/csio_rnode.c:869: warning: Function parameter or member 'fwevt' not described in 'csio_rnode_fwevt_handler'

Link: https://lore.kernel.org/r/20200723122446.1329773-25-lee.jones@linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Staticify non-external functions

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_ioc.c:5023:1: warning: no previous prototype for ‘bfa_diag_intr’ [-Wmissing-prototypes]
 5023 | bfa_diag_intr(void *diagarg, struct bfi_mbmsg_s *msg)
 | ^~~~~~~~~~~~~
 drivers/scsi/bfa/bfa_ioc.c:6966:1: warning: no previous prototype for ‘bfa_flash_sem_get’ [-Wmissing-prototypes]
 6966 | bfa_flash_sem_get(void __iomem *bar)
 | ^~~~~~~~~~~~~~~~~
 drivers/scsi/bfa/bfa_ioc.c:6979:1: warning: no previous prototype for ‘bfa_flash_sem_put’ [-Wmissing-prototypes]
 6979 | bfa_flash_sem_put(void __iomem *bar)
 | ^~~~~~~~~~~~~~~~~

Link: https://lore.kernel.org/r/20200723122446.1329773-24-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: csiostor: Remove 2 unused variables {mc,edc}_bist_status_rdata_reg

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/csiostor/csio_hw_t5.c: In function ‘csio_t5_mc_read’:
 drivers/scsi/csiostor/csio_hw_t5.c:151:11: warning: variable ‘mc_bist_status_rdata_reg’ set but not used [-Wunused-but-set-variable]
 151 | uint32_t mc_bist_status_rdata_reg, mc_bist_data_pattern_reg;
 | ^~~~~~~~~~~~~~~~~~~~~~~~
 drivers/scsi/csiostor/csio_hw_t5.c: In function ‘csio_t5_edc_read’:
 drivers/scsi/csiostor/csio_hw_t5.c:199:38: warning: variable ‘edc_bist_status_rdata_reg’ set but not used [-Wunused-but-set-variable]
 199 | uint32_t edc_bist_cmd_data_pattern, edc_bist_status_rdata_reg;
 | ^~~~~~~~~~~~~~~~~~~~~~~~~

Link: https://lore.kernel.org/r/20200723122446.1329773-23-lee.jones@linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: csiostor: Mark known unused variable as __always_unused

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/csiostor/csio_hw.c: In function ‘csio_hw_get_vpd_params’:
 drivers/scsi/csiostor/csio_hw.c:309:8: warning: variable ‘s’ set but not used [-Wunused-but-set-variable]

Link: https://lore.kernel.org/r/20200723122446.1329773-22-lee.jones@linaro.org
Cc: Arkadiusz Drabczyk <arkadiusz@drabczyk.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Remove a few unused variables 'pgoff' and 't'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_iocpf_sm_fwcheck_entry’:
 drivers/scsi/bfa/bfa_ioc.c:704:27: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_ioc_fwver_get’:
 drivers/scsi/bfa/bfa_ioc.c:1443:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_ioc_fwsig_invalidate’:
 drivers/scsi/bfa/bfa_ioc.c:1665:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_ioc_download_fw’:
 drivers/scsi/bfa/bfa_ioc.c:1866:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_diag_memtest_done’:
 drivers/scsi/bfa/bfa_ioc.c:4766:13: warning: variable ‘pgoff’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/bfa/bfa_ioc.c: In function ‘bfa_flash_fifo_flush’:
 drivers/scsi/bfa/bfa_ioc.c:6787:6: warning: variable ‘t’ set but not used [-Wunused-but-set-variable]

Link: https://lore.kernel.org/r/20200723122446.1329773-21-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Add description for lpfc_release_rpi()'s 'ndlpl param

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_nportdisc.c:1079: warning: Function parameter or member 'ndlp' not described in 'lpfc_release_rpi'

Link: https://lore.kernel.org/r/20200723122446.1329773-20-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix a bunch of kerneldoc misdemeanors

Adding, removing and correcting function parameter descriptions.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Function parameter or member 'vport' not described in 'lpfc_reg_vpi'
 drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'phba' description in 'lpfc_reg_vpi'
 drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'vpi' description in 'lpfc_reg_vpi'
 drivers/scsi/lpfc/lpfc_mbox.c:886: warning: Excess function parameter 'sid' description in 'lpfc_reg_vpi'
 drivers/scsi/lpfc/lpfc_mbox.c:1218: warning: Function parameter or member 'ring' not described in 'lpfc_config_ring'
 drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Function parameter or member 'mboxq' not described in 'lpfc_mbox_tmo_val'
 drivers/scsi/lpfc/lpfc_mbox.c:1626: warning: Excess function parameter 'cmd' description in 'lpfc_mbox_tmo_val'
 drivers/scsi/lpfc/lpfc_mbox.c:1710: warning: Function parameter or member 'sge' not described in 'lpfc_sli4_mbx_sge_get'
 drivers/scsi/lpfc/lpfc_mbox.c:1780: warning: Function parameter or member 'emb' not described in 'lpfc_sli4_config'
 drivers/scsi/lpfc/lpfc_mbox.c:2027: warning: Function parameter or member 'mboxq' not described in 'lpfc_sli4_mbx_read_fcf_rec'
 drivers/scsi/lpfc/lpfc_mbox.c:2078: warning: Function parameter or member 'phba' not described in 'lpfc_request_features'

Link: https://lore.kernel.org/r/20200723122446.1329773-19-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Rename function parameter descriptions

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_bsg.c:811: warning: Function parameter or member 'bsg_job' not described in 'qla4xxx_process_vendor_specific'
 drivers/scsi/qla4xxx/ql4_bsg.c:811: warning: Excess function parameter 'job' description in 'qla4xxx_process_vendor_specific'
 drivers/scsi/qla4xxx/ql4_bsg.c:858: warning: Function parameter or member 'bsg_job' not described in 'qla4xxx_bsg_request'
 drivers/scsi/qla4xxx/ql4_bsg.c:858: warning: Excess function parameter 'job' description in 'qla4xxx_bsg_request'

Link: https://lore.kernel.org/r/20200723122446.1329773-18-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Add and rename a whole bunch of function parameter descriptions

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_init.c:1136: warning: Function parameter or member 't' not described in 'lpfc_hb_timeout'
 drivers/scsi/lpfc/lpfc_init.c:1136: warning: Excess function parameter 'ptr' description in 'lpfc_hb_timeout'
 drivers/scsi/lpfc/lpfc_init.c:1170: warning: Function parameter or member 't' not described in 'lpfc_rrq_timeout'
 drivers/scsi/lpfc/lpfc_init.c:1170: warning: Excess function parameter 'ptr' description in 'lpfc_rrq_timeout'
 drivers/scsi/lpfc/lpfc_init.c:1232: warning: Function parameter or member 'work' not described in 'lpfc_idle_stat_delay_work'
 drivers/scsi/lpfc/lpfc_init.c:1817: warning: Function parameter or member 'en_rn_msg' not described in 'lpfc_sli4_port_sta_fn_reset'
 drivers/scsi/lpfc/lpfc_init.c:3033: warning: Function parameter or member 'mbx_action' not described in 'lpfc_block_mgmt_io'
 drivers/scsi/lpfc/lpfc_init.c:3481: warning: Function parameter or member 'mbx_action' not described in 'lpfc_offline_prep'
 drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'phba' not described in 'lpfc_new_io_buf'
 drivers/scsi/lpfc/lpfc_init.c:4150: warning: Function parameter or member 'num_to_alloc' not described in 'lpfc_new_io_buf'
 drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'vport' description in 'lpfc_new_io_buf'
 drivers/scsi/lpfc/lpfc_init.c:4150: warning: Excess function parameter 'num_to_allocate' description in 'lpfc_new_io_buf'
 drivers/scsi/lpfc/lpfc_init.c:4736: warning: Function parameter or member 't' not described in 'lpfc_sli4_fcf_redisc_wait_tmo'
 drivers/scsi/lpfc/lpfc_init.c:4736: warning: Excess function parameter 'ptr' description in 'lpfc_sli4_fcf_redisc_wait_tmo'
 drivers/scsi/lpfc/lpfc_init.c:5103: warning: Excess function parameter 'evt_code' description in 'lpfc_async_link_speed_to_read_top'
 drivers/scsi/lpfc/lpfc_init.c:5377: warning: Function parameter or member 'acqe_sli' not described in 'lpfc_sli4_async_sli_evt'
 drivers/scsi/lpfc/lpfc_init.c:5377: warning: Excess function parameter 'acqe_fc' description in 'lpfc_sli4_async_sli_evt'
 drivers/scsi/lpfc/lpfc_init.c:5634: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_perform_all_vport_cvl'
 drivers/scsi/lpfc/lpfc_init.c:5634: warning: Excess function parameter 'vport' description in 'lpfc_sli4_perform_all_vport_cvl'
 drivers/scsi/lpfc/lpfc_init.c:5655: warning: Function parameter or member 'acqe_fip' not described in 'lpfc_sli4_async_fip_evt'
 drivers/scsi/lpfc/lpfc_init.c:5655: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_fip_evt'
 drivers/scsi/lpfc/lpfc_init.c:5908: warning: Function parameter or member 'acqe_dcbx' not described in 'lpfc_sli4_async_dcbx_evt'
 drivers/scsi/lpfc/lpfc_init.c:5908: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_dcbx_evt'
 drivers/scsi/lpfc/lpfc_init.c:5927: warning: Function parameter or member 'acqe_grp5' not described in 'lpfc_sli4_async_grp5_evt'
 drivers/scsi/lpfc/lpfc_init.c:5927: warning: Excess function parameter 'acqe_link' description in 'lpfc_sli4_async_grp5_evt'
 drivers/scsi/lpfc/lpfc_init.c:7279: warning: Function parameter or member 'iocb_count' not described in 'lpfc_init_iocb_list'
 drivers/scsi/lpfc/lpfc_init.c:8227: warning: Function parameter or member 'if_type' not described in 'lpfc_sli4_bar1_register_memmap'
 drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'phba' description in 'LINK_FLAGS_DEF'
 drivers/scsi/lpfc/lpfc_init.c:8414: warning: Excess function parameter 'rdconf' description in 'LINK_FLAGS_DEF'
 drivers/scsi/lpfc/lpfc_init.c:10734: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli_enable_intr'
 drivers/scsi/lpfc/lpfc_init.c:11241: warning: Function parameter or member 'eqlist' not described in 'lpfc_cpuhp_get_eq'
 drivers/scsi/lpfc/lpfc_init.c:11726: warning: Function parameter or member 'cfg_mode' not described in 'lpfc_sli4_enable_intr'
 drivers/scsi/lpfc/lpfc_init.c:12997: warning: Excess function parameter 'ret' description in 'lpfc_write_firmware'
 drivers/scsi/lpfc/lpfc_init.c:13103: warning: Function parameter or member 'fw_upgrade' not described in 'lpfc_sli4_request_firmware_update'

Link: https://lore.kernel.org/r/20200723122446.1329773-17-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Use __printf() format notation

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_init.c: In function ‘lpfc_dbg_print’:
 drivers/scsi/lpfc/lpfc_init.c:14212:6: warning: function ‘lpfc_dbg_print’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
 14212 | sizeof(phba->dbg_log[idx].log), fmt, args);
 | ^~~~~~

Link: https://lore.kernel.org/r/20200723122446.1329773-16-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove set but unused variable 'status'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_83xx.c: In function ‘qla4_83xx_dump_pause_control_regs’:
 drivers/scsi/qla4xxx/ql4_83xx.c:1409:9: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
 1409 | int i, status = QLA_SUCCESS;
 | ^~~~~~

Link: https://lore.kernel.org/r/20200723122446.1329773-15-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ips: Convert strnlen() to memcpy() since result should not be NUL terminated

Fixes the following W=1 kernel build warning(s):

 In file included from arch/arm/include/asm/io.h:23,
 from drivers/scsi/ips.c:164:
 In function ‘strncpy’,
 inlined from ‘ips_send_cmd’ at drivers/scsi/ips.c:3522:6:
 include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ output
 truncated before terminating nul cop ying 4 bytes from a string of the same length [-Wstringop-truncation]
 297 | #define __underlying_strncpy __builtin_strncpy
 | ^
 include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
 307 | return __underlying_strncpy(p, q, size);
 | ^~~~~~~~~~~~~~~~~~~~
 NB: Lots of these - snipping for brevity

Link: https://lore.kernel.org/r/20200723122446.1329773-14-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: ipslinux@adaptec.com
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ips: Remove some set but unused variables

Intentionally keeping all register reads/writes.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/ips.c: In function ‘ips_init_copperhead’:
 drivers/scsi/ips.c:4700:10: warning: variable ‘ConfigByte’ set but not used [-Wunused-but-set-variable]
 4700 | uint8_t ConfigByte[IPS_MAX_CONFIG_BYTES];
 | ^~~~~~~~~~
 drivers/scsi/ips.c: In function ‘ips_init_copperhead_memio’:
 drivers/scsi/ips.c:4794:10: warning: variable ‘ConfigByte’ set but not used [-Wunused-but-set-variable]
 4794 | uint8_t ConfigByte[IPS_MAX_CONFIG_BYTES];
 | ^~~~~~~~~~
 drivers/scsi/ips.c: In function ‘ips_init_phase1’:
 drivers/scsi/ips.c:6839:10: warning: variable ‘func’ set but not used [-Wunused-but-set-variable]
 6839 | uint8_t func;
 | ^~~~
 drivers/scsi/ips.c:6838:10: warning: variable ‘bus’ set but not used [-Wunused-but-set-variable]
 6838 | uint8_t bus;
 | ^~~

Link: https://lore.kernel.org/r/20200723122446.1329773-13-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: ipslinux@adaptec.com
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qedi: Remove 2 set but unused variables

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qedi/qedi_main.c: In function ‘qedi_queue_cqe’:
 drivers/scsi/qedi/qedi_main.c:1158:21: warning: variable ‘conn’ set but not used [-Wunused-but-set-variable]
 1158 | struct iscsi_conn *conn;
 | ^~~~
 drivers/scsi/qedi/qedi_main.c: In function ‘__qedi_probe’:
 drivers/scsi/qedi/qedi_main.c:2432:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
 2432 | u16 tmp;
 | ^~~

Link: https://lore.kernel.org/r/20200723122446.1329773-12-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@cavium.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Demote seemingly unintentional kerneldoc header

This is the only use of kerneldoc in the source file and no descriptions
are provided.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_fcpim.c:3829: warning: Function parameter or member 'bfa' not described in 'bfa_fcpim_get_throttle_cfg'
 drivers/scsi/bfa/bfa_fcpim.c:3829: warning: Function parameter or member 'drv_cfg_param' not described in 'bfa_fcpim_get_throttle_cfg'

Link: https://lore.kernel.org/r/20200723122446.1329773-11-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Remove set but unused variable 'rp'

This change subsequently makes 'rp_fcs' unused also.  Remove that too.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_fcpim.c: In function ‘bfa_fcpim_lunmask_delete’:
 drivers/scsi/bfa/bfa_fcpim.c:2338:22: warning: variable ‘rp’ set but not used [-Wunused-but-set-variable]
 2338 | struct bfa_rport_s *rp = NULL;
 | ^~

Link: https://lore.kernel.org/r/20200723122446.1329773-10-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bnx2i: Add missing descriptions for 'attr' parameter

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bnx2i/bnx2i_sysfs.c:40: warning: Function parameter or member 'attr' not described in 'bnx2i_show_sq_info'
 drivers/scsi/bnx2i/bnx2i_sysfs.c:60: warning: Function parameter or member 'attr' not described in 'bnx2i_set_sq_info'
 drivers/scsi/bnx2i/bnx2i_sysfs.c:96: warning: Function parameter or member 'attr' not described in 'bnx2i_show_ccell_info'
 drivers/scsi/bnx2i/bnx2i_sysfs.c:114: warning: Function parameter or member 'attr' not described in 'bnx2i_set_ccell_info'

Link: https://lore.kernel.org/r/20200723122446.1329773-9-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Staticify local functions

These calls are not invoked externally.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfa_port.c:760:1: warning: no previous prototype for ‘bfa_cee_isr’ [-Wmissing-prototypes]
 760 | bfa_cee_isr(void *cbarg, struct bfi_mbmsg_s *m)
 | ^~~~~~~~~~~
 drivers/scsi/bfa/bfa_port.c:796:1: warning: no previous prototype for ‘bfa_cee_notify’ [-Wmissing-prototypes]
 796 | bfa_cee_notify(void *arg, enum bfa_ioc_event_e event)
 | ^~~~~~~~~~~~~~

Link: https://lore.kernel.org/r/20200723122446.1329773-8-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: ufs-exynos: Demote seemingly unintentional kerneldoc header

This is the only use of kerneldoc in the source file and no descriptions
are provided.

Fixes the following W=1 kernel build warning(s):

In file included from  drivers/scsi/ufs/ufs-exynos.c:23:
 drivers/scsi/ufs/ufs-exynos.c:234: warning: Function parameter or member 'ufs' not described in 'exynos_ufs_auto_ctrl_hcc'
 drivers/scsi/ufs/ufs-exynos.c:234: warning: Function parameter or member 'en' not described in 'exynos_ufs_auto_ctrl_hcc'

Link: https://lore.kernel.org/r/20200723122446.1329773-7-lee.jones@linaro.org
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Seungwon Jeon <essuuj@gmail.com>
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bnx2i: Fix parameter misnaming in function header

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bnx2i/bnx2i_init.c:83: warning: Function parameter or member 'dev' not described in 'bnx2i_identify_device'
 drivers/scsi/bnx2i/bnx2i_init.c:83: warning: Excess function parameter 'cnic' description in 'bnx2i_identify_device'

Link: https://lore.kernel.org/r/20200723122446.1329773-5-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Anil Veerabhadrappa <anilgv@broadcom.com>
Cc: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: ufs-qcom: Demote nonconformant kerneldoc headers

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/ufs/ufs-qcom.c:253: warning: Function parameter or member 'hba' not described in 'ufs_qcom_host_reset'
 drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'hba' not described in 'ufs_qcom_cfg_timers'
 drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'gear' not described in 'ufs_qcom_cfg_timers'
 drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'hs' not described in 'ufs_qcom_cfg_timers'
 drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'rate' not described in 'ufs_qcom_cfg_timers'
 drivers/scsi/ufs/ufs-qcom.c:383: warning: Function parameter or member 'update_link_startup_timer' not described in 'ufs_qcom_cfg_timers'
 drivers/scsi/ufs/ufs-qcom.c:1738: error: Cannot parse struct or union!

Link: https://lore.kernel.org/r/20200723122446.1329773-4-lee.jones@linaro.org
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix kerneldoc parameter formatting/misnaming/missing issues

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_hbadisc.c:1209: warning: Function parameter or member 'phba' not described in 'lpfc_sli4_clear_fcf_rr_bmask'
 drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Function parameter or member 'sw_name' not described in 'lpfc_sw_name_match'
 drivers/scsi/lpfc/lpfc_hbadisc.c:1309: warning: Excess function parameter 'fab_name' description in 'lpfc_sw_name_match'
 drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Function parameter or member 'fcf_rec' not described in 'lpfc_copy_fcf_record'
 drivers/scsi/lpfc/lpfc_hbadisc.c:1397: warning: Excess function parameter 'fcf' description in 'lpfc_copy_fcf_record'
 drivers/scsi/lpfc/lpfc_hbadisc.c:1956: warning: Cannot understand  lpfc_sli4_fcf_record_match - testing new FCF record for matching existing FCF
 on line 1956 - I thought it was a doc line
 drivers/scsi/lpfc/lpfc_hbadisc.c:2078: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_del'
 drivers/scsi/lpfc/lpfc_hbadisc.c:2109: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_set_fcf_flogi_fail'
 drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_pri_list_add'
 drivers/scsi/lpfc/lpfc_hbadisc.c:2135: warning: Function parameter or member 'new_fcf_record' not described in 'lpfc_sli4_fcf_pri_list_add'

Link: https://lore.kernel.org/r/20200723122446.1329773-3-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix some function parameter descriptions

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_els.c:3619: warning: Function parameter or member 't' not described in 'lpfc_els_retry_delay'
 drivers/scsi/lpfc/lpfc_els.c:3619: warning: Excess function parameter 'ptr' description in 'lpfc_els_retry_delay'
 drivers/scsi/lpfc/lpfc_els.c:4877: warning: Function parameter or member 'rejectError' not described in 'lpfc_els_rsp_reject'
 drivers/scsi/lpfc/lpfc_els.c:7900: warning: Function parameter or member 't' not described in 'lpfc_els_timeout'
 drivers/scsi/lpfc/lpfc_els.c:7900: warning: Excess function parameter 'ptr' description in 'lpfc_els_timeout'
 drivers/scsi/lpfc/lpfc_els.c:8272: warning: Function parameter or member 'payload' not described in 'lpfc_send_els_event'
 drivers/scsi/lpfc/lpfc_els.c:8272: warning: Excess function parameter 'cmd' description in 'lpfc_send_els_event'
 drivers/scsi/lpfc/lpfc_els.c:8355: warning: Function parameter or member 'tlv' not described in 'lpfc_els_rcv_fpin_li'
 drivers/scsi/lpfc/lpfc_els.c:8355: warning: Excess function parameter 'lnk_not' description in 'lpfc_els_rcv_fpin_li'
 drivers/scsi/lpfc/lpfc_els.c:9688: warning: Function parameter or member 't' not described in 'lpfc_fabric_block_timeout'
 drivers/scsi/lpfc/lpfc_els.c:9688: warning: Excess function parameter 'ptr' description in 'lpfc_fabric_block_timeout'

Link: https://lore.kernel.org/r/20200723122446.1329773-2-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: cxgb3i: Remove bad documentation and demote kerneldoc header

Also move the header block above the correct function.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Function parameter or member 'dev' not described in 'arp_failure_skb_discard'
 drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Function parameter or member 'skb' not described in 'arp_failure_skb_discard'
 drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Excess function parameter 'c3cn' description in 'arp_failure_skb_discard'
 drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:390: warning: Excess function parameter 'req_completion' description in 'arp_failure_skb_discard'
 drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:895: warning: Function parameter or member 'csk' not described in 'l2t_put'
 drivers/scsi/cxgbi/cxgb3i/cxgb3i.c:895: warning: Excess function parameter 'c3cn' description in 'l2t_put'

Link: https://lore.kernel.org/r/20200721164148.2617584-41-lee.jones@linaro.org
Cc: Karen Xie <kxie@chelsio.com>
Cc: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sym53c8xx_2: Ensure variable has the same stipulations as code using it

Only declare 'tp' and 'lp' if they are going to be used.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/sym53c8xx_2/sym_hipd.c: In function ‘sym_complete_error’:
 drivers/scsi/sym53c8xx_2/sym_hipd.c:5356:18: warning: variable ‘lp’ set but not used [-Wunused-but-set-variable]
 drivers/scsi/sym53c8xx_2/sym_hipd.c: In function ‘sym_complete_ok’:
 drivers/scsi/sym53c8xx_2/sym_hipd.c:5485:18: warning: variable ‘lp’ set but not used [-Wunused-but-set-variable]

Link: https://lore.kernel.org/r/20200721164148.2617584-39-lee.jones@linaro.org
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Gerard Roudier <groudier@free.fr>
Cc: Wolfgang Stanglmeier <wolf@cologne.de>
Cc: Stefan Esser <se@mi.Uni-Koeln.de>
Cc: Richard Waltham <dormouse@farsrobt.demon.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sym53c8xx_2: Add missing description for 'pdev'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/sym53c8xx_2/sym_glue.c:1784: warning: Function parameter or member 'pdev' not described in 'sym2_reset_workarounds'

Link: https://lore.kernel.org/r/20200721164148.2617584-38-lee.jones@linaro.org
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Gerard Roudier <groudier@free.fr>
Cc: Wolfgang Stanglmeier <wolf@cologne.de>
Cc: Stefan Esser <se@mi.Uni-Koeln.de>
Cc: Richard Waltham <dormouse@farsrobt.demon.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Ensure variable has the same stipulations as code using it

'pg_addr' is only used when CONFIG_X86 is defined.  So only declare it if
CONFIG_X86 is defined.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_sli.c: In function ‘lpfc_wq_create’:
 drivers/scsi/lpfc/lpfc_sli.c:15813:16: warning: unused variable ‘pg_addr’ [-Wunused-variable]
 15813 | unsigned long pg_addr;
 | ^~~~~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-37-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: bfa: Staticify all local functions

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/bfa/bfad_bsg.c:19:1: warning: no previous prototype for ‘bfad_iocmd_ioc_enable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:42:1: warning: no previous prototype for ‘bfad_iocmd_ioc_disable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:150:1: warning: no previous prototype for ‘bfad_iocmd_ioc_get_fwstats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:180:1: warning: no previous prototype for ‘bfad_iocmd_ioc_reset_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:198:1: warning: no previous prototype for ‘bfad_iocmd_ioc_set_name’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:212:1: warning: no previous prototype for ‘bfad_iocmd_iocfc_get_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:223:1: warning: no previous prototype for ‘bfad_iocmd_ioc_fw_sig_inv’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:235:1: warning: no previous prototype for ‘bfad_iocmd_iocfc_set_intr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:248:1: warning: no previous prototype for ‘bfad_iocmd_port_enable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:269:1: warning: no previous prototype for ‘bfad_iocmd_port_disable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:319:1: warning: no previous prototype for ‘bfad_iocmd_port_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:353:1: warning: no previous prototype for ‘bfad_iocmd_port_reset_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:374:1: warning: no previous prototype for ‘bfad_iocmd_set_port_cfg’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:394:1: warning: no previous prototype for ‘bfad_iocmd_port_cfg_maxfrsize’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:408:1: warning: no previous prototype for ‘bfad_iocmd_port_cfg_bbcr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:431:1: warning: no previous prototype for ‘bfad_iocmd_port_get_bbcr_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:469:1: warning: no previous prototype for ‘bfad_iocmd_lport_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:493:1: warning: no previous prototype for ‘bfad_iocmd_lport_reset_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:527:1: warning: no previous prototype for ‘bfad_iocmd_lport_get_iostats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:552:1: warning: no previous prototype for ‘bfad_iocmd_lport_get_rports’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:594:1: warning: no previous prototype for ‘bfad_iocmd_rport_get_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:680:1: warning: no previous prototype for ‘bfad_iocmd_rport_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:721:1: warning: no previous prototype for ‘bfad_iocmd_rport_clr_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:757:1: warning: no previous prototype for ‘bfad_iocmd_rport_set_speed’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:793:1: warning: no previous prototype for ‘bfad_iocmd_vport_get_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:816:1: warning: no previous prototype for ‘bfad_iocmd_vport_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:844:1: warning: no previous prototype for ‘bfad_iocmd_vport_clr_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:911:1: warning: no previous prototype for ‘bfad_iocmd_qos_set_bw’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:924:1: warning: no previous prototype for ‘bfad_iocmd_ratelim’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:953:1: warning: no previous prototype for ‘bfad_iocmd_ratelim_speed’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:982:1: warning: no previous prototype for ‘bfad_iocmd_cfg_fcpim’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:995:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_get_modstats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1017:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_clr_modstats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1039:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_get_del_itn_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1164:1: warning: no previous prototype for ‘bfad_iocmd_fcport_enable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1177:1: warning: no previous prototype for ‘bfad_iocmd_fcport_disable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1190:1: warning: no previous prototype for ‘bfad_iocmd_ioc_get_pcifn_cfg’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1212:1: warning: no previous prototype for ‘bfad_iocmd_pcifn_create’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1235:1: warning: no previous prototype for ‘bfad_iocmd_pcifn_delete’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1257:1: warning: no previous prototype for ‘bfad_iocmd_pcifn_bw’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1281:1: warning: no previous prototype for ‘bfad_iocmd_adapter_cfg_mode’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1304:1: warning: no previous prototype for ‘bfad_iocmd_port_cfg_mode’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1328:1: warning: no previous prototype for ‘bfad_iocmd_ablk_optrom’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1354:1: warning: no previous prototype for ‘bfad_iocmd_faa_query’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1377:1: warning: no previous prototype for ‘bfad_iocmd_cee_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1413:1: warning: no previous prototype for ‘bfad_iocmd_cee_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1450:1: warning: no previous prototype for ‘bfad_iocmd_cee_reset_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1464:1: warning: no previous prototype for ‘bfad_iocmd_sfp_media’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1486:1: warning: no previous prototype for ‘bfad_iocmd_sfp_speed’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1507:1: warning: no previous prototype for ‘bfad_iocmd_flash_get_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1528:1: warning: no previous prototype for ‘bfad_iocmd_flash_erase_part’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1548:1: warning: no previous prototype for ‘bfad_iocmd_flash_update_part’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1580:1: warning: no previous prototype for ‘bfad_iocmd_flash_read_part’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1612:1: warning: no previous prototype for ‘bfad_iocmd_diag_temp’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1634:1: warning: no previous prototype for ‘bfad_iocmd_diag_memtest’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1657:1: warning: no previous prototype for ‘bfad_iocmd_diag_loopback’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1680:1: warning: no previous prototype for ‘bfad_iocmd_diag_fwping’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1704:1: warning: no previous prototype for ‘bfad_iocmd_diag_queuetest’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1725:1: warning: no previous prototype for ‘bfad_iocmd_diag_sfp’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1748:1: warning: no previous prototype for ‘bfad_iocmd_diag_led’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1761:1: warning: no previous prototype for ‘bfad_iocmd_diag_beacon_lport’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1776:1: warning: no previous prototype for ‘bfad_iocmd_diag_lb_stat’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1791:1: warning: no previous prototype for ‘bfad_iocmd_diag_dport_enable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1813:1: warning: no previous prototype for ‘bfad_iocmd_diag_dport_disable’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1833:1: warning: no previous prototype for ‘bfad_iocmd_diag_dport_start’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1858:1: warning: no previous prototype for ‘bfad_iocmd_diag_dport_show’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1873:1: warning: no previous prototype for ‘bfad_iocmd_phy_get_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1894:1: warning: no previous prototype for ‘bfad_iocmd_phy_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1915:1: warning: no previous prototype for ‘bfad_iocmd_phy_read’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1947:1: warning: no previous prototype for ‘bfad_iocmd_vhba_query’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1966:1: warning: no previous prototype for ‘bfad_iocmd_phy_update’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:1996:1: warning: no previous prototype for ‘bfad_iocmd_porglog_get’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2016:1: warning: no previous prototype for ‘bfad_iocmd_debug_fw_core’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2050:1: warning: no previous prototype for ‘bfad_iocmd_debug_ctl’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2071:1: warning: no previous prototype for ‘bfad_iocmd_porglog_ctl’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2085:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_cfg_profile’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2129:1: warning: no previous prototype for ‘bfad_iocmd_fcport_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2154:1: warning: no previous prototype for ‘bfad_iocmd_fcport_reset_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2178:1: warning: no previous prototype for ‘bfad_iocmd_boot_cfg’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2200:1: warning: no previous prototype for ‘bfad_iocmd_boot_query’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2222:1: warning: no previous prototype for ‘bfad_iocmd_preboot_query’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2241:1: warning: no previous prototype for ‘bfad_iocmd_ethboot_cfg’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2264:1: warning: no previous prototype for ‘bfad_iocmd_ethboot_query’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2287:1: warning: no previous prototype for ‘bfad_iocmd_cfg_trunk’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2327:1: warning: no previous prototype for ‘bfad_iocmd_trunk_get_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2350:1: warning: no previous prototype for ‘bfad_iocmd_qos’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2378:1: warning: no previous prototype for ‘bfad_iocmd_qos_get_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2404:1: warning: no previous prototype for ‘bfad_iocmd_qos_get_vc_attr’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2436:1: warning: no previous prototype for ‘bfad_iocmd_qos_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2468:1: warning: no previous prototype for ‘bfad_iocmd_qos_reset_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2499:1: warning: no previous prototype for ‘bfad_iocmd_vf_get_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2522:1: warning: no previous prototype for ‘bfad_iocmd_vf_clr_stats’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2559:1: warning: no previous prototype for ‘bfad_iocmd_lunmask’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2582:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_lunmask_query’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2596:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_cfg_lunmask’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2615:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_throttle_query’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2630:1: warning: no previous prototype for ‘bfad_iocmd_fcpim_throttle_set’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2645:1: warning: no previous prototype for ‘bfad_iocmd_tfru_read’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2667:1: warning: no previous prototype for ‘bfad_iocmd_tfru_write’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2689:1: warning: no previous prototype for ‘bfad_iocmd_fruvpd_read’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2711:1: warning: no previous prototype for ‘bfad_iocmd_fruvpd_update’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:2733:1: warning: no previous prototype for ‘bfad_iocmd_fruvpd_get_max_size’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3181:1: warning: no previous prototype for ‘bfad_fcxp_get_req_sgaddr_cb’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3193:1: warning: no previous prototype for ‘bfad_fcxp_get_req_sglen_cb’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3203:1: warning: no previous prototype for ‘bfad_fcxp_get_rsp_sgaddr_cb’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3215:1: warning: no previous prototype for ‘bfad_fcxp_get_rsp_sglen_cb’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3225:1: warning: no previous prototype for ‘bfad_send_fcpt_cb’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3240:1: warning: no previous prototype for ‘bfad_fcxp_map_sg’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3284:1: warning: no previous prototype for ‘bfad_fcxp_free_mem’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3302:1: warning: no previous prototype for ‘bfad_fcxp_bsg_send’ [-Wmissing-prototypes]
 drivers/scsi/bfa/bfad_bsg.c:3342:1: warning: no previous prototype for ‘bfad_im_bsg_els_ct_request’ [-Wmissing-prototypes]

Link: https://lore.kernel.org/r/20200721164148.2617584-36-lee.jones@linaro.org
Cc: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: Sudarsana Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: csiostor: Demote kerneldoc that fails to meet the criteria

This matches some of the other headers in the file.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/csiostor/csio_lnode.c:2079: warning: Function parameter or member 'hw' not described in 'csio_lnode_init'
 drivers/scsi/csiostor/csio_lnode.c:2079: warning: Function parameter or member 'pln' not described in 'csio_lnode_init'

Link: https://lore.kernel.org/r/20200721164148.2617584-35-lee.jones@linaro.org
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Supply description for 'code'

Demote other headers which are clearly not kerneldoc.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_nx.c:983: warning: Function parameter or member 'ha' not described in 'qla4_82xx_pinit_from_rom'
 drivers/scsi/qla4xxx/ql4_nx.c:983: warning: Function parameter or member 'verbose' not described in 'qla4_82xx_pinit_from_rom'
 drivers/scsi/qla4xxx/ql4_nx.c:3225: warning: Function parameter or member 'code' not described in 'qla4_8xxx_uevent_emit'
 drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'ha' not described in 'qla4_82xx_read_optrom_data'
 drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'buf' not described in 'qla4_82xx_read_optrom_data'
 drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'offset' not described in 'qla4_82xx_read_optrom_data'
 drivers/scsi/qla4xxx/ql4_nx.c:3697: warning: Function parameter or member 'length' not described in 'qla4_82xx_read_optrom_data'

Link: https://lore.kernel.org/r/20200721164148.2617584-34-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove three set but unused variables

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_nx.c: In function ‘qla4_84xx_minidump_process_rddfe’:
 drivers/scsi/qla4xxx/ql4_nx.c:2648:23: warning: variable ‘data_size’ set but not used [-Wunused-but-set-variable]
 2648 | uint32_t poll, mask, data_size, modify_mask;
 | ^~~~~~~~~
 drivers/scsi/qla4xxx/ql4_nx.c: In function ‘qla4_84xx_minidump_process_rdmdio’:
 drivers/scsi/qla4xxx/ql4_nx.c:2745:11: warning: variable ‘poll’ set but not used [-Wunused-but-set-variable]
 2745 | uint32_t poll, mask;
 | ^~~~
 drivers/scsi/qla4xxx/ql4_nx.c: In function ‘qla4_84xx_minidump_process_pollwr’:
 drivers/scsi/qla4xxx/ql4_nx.c:2816:47: warning: variable ‘mask’ set but not used [-Wunused-but-set-variable]
 2816 | uint32_t addr1, addr2, value1, value2, poll, mask, r_value;
 | ^~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-33-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: csiostor: Fix misnamed function parameter

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/csiostor/csio_init.c:595: warning: Function parameter or member 'pln' not described in 'csio_shost_init'
 drivers/scsi/csiostor/csio_init.c:595: warning: Excess function parameter 'os_pln' description in 'csio_shost_init'

Link: https://lore.kernel.org/r/20200721164148.2617584-32-lee.jones@linaro.org
Cc: Saurav Girepunje <saurav.girepunje@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix-up formatting/docrot where appropriate

Other headers have been demoted as they are too far out of sync and ideally
require effort from the authors.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'usr_flg' not described in 'lpfc_gen_req'
 drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'num_entry' not described in 'lpfc_gen_req'
 drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'tmo' not described in 'lpfc_gen_req'
 drivers/scsi/lpfc/lpfc_ct.c:321: warning: Function parameter or member 'retry' not described in 'lpfc_gen_req'
 drivers/scsi/lpfc/lpfc_ct.c:413: warning: Function parameter or member 'rsp_size' not described in 'lpfc_ct_cmd'
 drivers/scsi/lpfc/lpfc_ct.c:413: warning: Function parameter or member 'retry' not described in 'lpfc_ct_cmd'
 drivers/scsi/lpfc/lpfc_ct.c:3030: warning: Function parameter or member 'cmdcode' not described in 'lpfc_fdmi_cmd'
 drivers/scsi/lpfc/lpfc_ct.c:3030: warning: Function parameter or member 'new_mask' not described in 'lpfc_fdmi_cmd'
 drivers/scsi/lpfc/lpfc_ct.c:3272: warning: Function parameter or member 't' not described in 'lpfc_delayed_disc_tmo'

Link: https://lore.kernel.org/r/20200721164148.2617584-31-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Document qla4xxx_process_ddb()'s 'conn_err'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_init.c:1170: warning: Function parameter or member 'conn_err' not described in 'qla4xxx_process_ddb_changed'

Link: https://lore.kernel.org/r/20200721164148.2617584-30-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Provide description for lpfc_mem_alloc()'s 'align' param

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_mem.c:85: warning: Function parameter or member 'align' not described in 'lpfc_mem_alloc'

Link: https://lore.kernel.org/r/20200721164148.2617584-29-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Repair function documentation headers

Fix one formatting issue, one misspelling and three missing descriptions.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_isr.c:588: warning: Excess function parameter 'ret' description in 'qla4_83xx_loopback_in_progress'
 drivers/scsi/qla4xxx/ql4_isr.c:661: warning: Function parameter or member 'mbox_status' not described in 'qla4xxx_isr_decode_mailbox'
 drivers/scsi/qla4xxx/ql4_isr.c:661: warning: Excess function parameter 'mailbox_status' description in 'qla4xxx_isr_decode_mailbox'
 drivers/scsi/qla4xxx/ql4_isr.c:1053: warning: Function parameter or member 'intr_status' not described in 'qla4_82xx_interrupt_service_routine'
 drivers/scsi/qla4xxx/ql4_isr.c:1078: warning: Function parameter or member 'intr_status' not described in 'qla4xxx_interrupt_service_routine'

Link: https://lore.kernel.org/r/20200721164148.2617584-28-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Fix some kerneldoc parameter documentation issues

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_os.c:4551: warning: Function parameter or member 't' not described in 'qla4xxx_timer'
 drivers/scsi/qla4xxx/ql4_os.c:4551: warning: Excess function parameter 'ha' description in 'qla4xxx_timer'
 drivers/scsi/qla4xxx/ql4_os.c:5312: warning: Function parameter or member 'work' not described in 'qla4xxx_do_dpc'
 drivers/scsi/qla4xxx/ql4_os.c:5312: warning: Excess function parameter 'data' description in 'qla4xxx_do_dpc'
 drivers/scsi/qla4xxx/ql4_os.c:8627: warning: Function parameter or member 'ent' not described in 'qla4xxx_probe_adapter'
 drivers/scsi/qla4xxx/ql4_os.c:8627: warning: Excess function parameter 'pci_device_id' description in 'qla4xxx_probe_adapter'
 drivers/scsi/qla4xxx/ql4_os.c:9008: warning: Function parameter or member 'pdev' not described in 'qla4xxx_remove_adapter'
 drivers/scsi/qla4xxx/ql4_os.c:9008: warning: Excess function parameter 'pci_dev' description in 'qla4xxx_remove_adapter'
 drivers/scsi/qla4xxx/ql4_os.c:9181: warning: Function parameter or member 'stgt' not described in 'qla4xxx_eh_wait_for_commands'
 drivers/scsi/qla4xxx/ql4_os.c:9181: warning: Function parameter or member 'sdev' not described in 'qla4xxx_eh_wait_for_commands'
 drivers/scsi/qla4xxx/ql4_os.c:9181: warning: Excess function parameter 't' description in 'qla4xxx_eh_wait_for_commands'
 drivers/scsi/qla4xxx/ql4_os.c:9181: warning: Excess function parameter 'l' description in 'qla4xxx_eh_wait_for_commands'
 drivers/scsi/qla4xxx/ql4_os.c:9646: warning: Function parameter or member 'pdev' not described in 'qla4xxx_pci_mmio_enabled'

Link: https://lore.kernel.org/r/20200721164148.2617584-27-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Staticify 'pm80xx_pci_mem_copy' and 'mpi_set_phy_profile_req'

These are not invoked externally.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/pm8001/pm80xx_hwi.c:69:6: warning: no previous prototype for ‘pm80xx_pci_mem_copy’ [-Wmissing-prototypes]
 69 | void pm80xx_pci_mem_copy(struct pm8001_hba_info *pm8001_ha, u32 soffset,
 | ^~~~~~~~~~~~~~~~~~~
 drivers/scsi/pm8001/pm80xx_hwi.c:5016:6: warning: no previous prototype for ‘mpi_set_phy_profile_req’ [-Wmissing-prototypes]
 5016 | void mpi_set_phy_profile_req(struct pm8001_hba_info *pm8001_ha,
 | ^~~~~~~~~~~~~~~~~~~~~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-26-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix-up around 120 documentation issues

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_sli.c:257: warning: Function parameter or member 'mqe' not described in 'lpfc_sli4_mq_put'
 drivers/scsi/lpfc/lpfc_sli.c:257: warning: Excess function parameter 'wqe' description in 'lpfc_sli4_mq_put'
 drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'hq' not described in 'lpfc_sli4_rq_put'
 drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'dq' not described in 'lpfc_sli4_rq_put'
 drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'hrqe' not described in 'lpfc_sli4_rq_put'
 drivers/scsi/lpfc/lpfc_sli.c:675: warning: Function parameter or member 'drqe' not described in 'lpfc_sli4_rq_put'
 drivers/scsi/lpfc/lpfc_sli.c:675: warning: Excess function parameter 'q' description in 'lpfc_sli4_rq_put'
 drivers/scsi/lpfc/lpfc_sli.c:675: warning: Excess function parameter 'wqe' description in 'lpfc_sli4_rq_put'
 drivers/scsi/lpfc/lpfc_sli.c:738: warning: Function parameter or member 'hq' not described in 'lpfc_sli4_rq_release'
 drivers/scsi/lpfc/lpfc_sli.c:738: warning: Function parameter or member 'dq' not described in 'lpfc_sli4_rq_release'
 drivers/scsi/lpfc/lpfc_sli.c:738: warning: Excess function parameter 'q' description in 'lpfc_sli4_rq_release'
 drivers/scsi/lpfc/lpfc_sli.c:1021: warning: Function parameter or member 'xritag' not described in 'lpfc_test_rrq_active'
 drivers/scsi/lpfc/lpfc_sli.c:1132: warning: Function parameter or member 'piocbq' not described in '__lpfc_sli_get_els_sglq'
 drivers/scsi/lpfc/lpfc_sli.c:1132: warning: Excess function parameter 'piocb' description in '__lpfc_sli_get_els_sglq'
 drivers/scsi/lpfc/lpfc_sli.c:1207: warning: Function parameter or member 'piocbq' not described in '__lpfc_sli_get_nvmet_sglq'
 drivers/scsi/lpfc/lpfc_sli.c:1207: warning: Excess function parameter 'piocb' description in '__lpfc_sli_get_nvmet_sglq'
 drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Function parameter or member 'rb_list' not described in 'lpfc_sli_hbqbuf_get'
 drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Excess function parameter 'phba' description in 'lpfc_sli_hbqbuf_get'
 drivers/scsi/lpfc/lpfc_sli.c:2243: warning: Excess function parameter 'hbqno' description in 'lpfc_sli_hbqbuf_get'
 drivers/scsi/lpfc/lpfc_sli.c:2262: warning: Function parameter or member 'hrq' not described in 'lpfc_sli_rqbuf_get'
 drivers/scsi/lpfc/lpfc_sli.c:2262: warning: Excess function parameter 'hbqno' description in 'lpfc_sli_rqbuf_get'
 drivers/scsi/lpfc/lpfc_sli.c:3429: warning: Function parameter or member 't' not described in 'lpfc_poll_eratt'
 drivers/scsi/lpfc/lpfc_sli.c:3429: warning: Excess function parameter 'ptr' description in 'lpfc_poll_eratt'
 drivers/scsi/lpfc/lpfc_sli.c:4115: warning: Excess function parameter 'pring' description in 'lpfc_sli_abort_fcp_rings'
 drivers/scsi/lpfc/lpfc_sli.c:5331: warning: Excess function parameter 'mboxq' description in 'lpfc_sli4_read_fcoe_params'
 drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'extnt_cnt' not described in 'lpfc_sli4_cfg_post_extnts'
 drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'type' not described in 'lpfc_sli4_cfg_post_extnts'
 drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'emb' not described in 'lpfc_sli4_cfg_post_extnts'
 drivers/scsi/lpfc/lpfc_sli.c:5879: warning: Function parameter or member 'mbox' not described in 'lpfc_sli4_cfg_post_extnts'
 drivers/scsi/lpfc/lpfc_sli.c:6459: warning: Function parameter or member 'pmb' not described in 'lpfc_sli4_ras_mbox_cmpl'
 drivers/scsi/lpfc/lpfc_sli.c:6459: warning: Excess function parameter 'pmboxq' description in 'lpfc_sli4_ras_mbox_cmpl'
 drivers/scsi/lpfc/lpfc_sli.c:6912: warning: Function parameter or member 'extnt_cnt' not described in 'lpfc_sli4_get_allocated_extnts'
 drivers/scsi/lpfc/lpfc_sli.c:6912: warning: Excess function parameter 'extnt_count' description in 'lpfc_sli4_get_allocated_extnts'
 drivers/scsi/lpfc/lpfc_sli.c:7064: warning: Excess function parameter 'pring' description in 'lpfc_sli4_repost_sgl_list'
 drivers/scsi/lpfc/lpfc_sli.c:7312: warning: Function parameter or member 'phba' not described in 'lpfc_init_idle_stat_hb'
 drivers/scsi/lpfc/lpfc_sli.c:8022: warning: Function parameter or member 't' not described in 'lpfc_mbox_timeout'
 drivers/scsi/lpfc/lpfc_sli.c:8022: warning: Excess function parameter 'ptr' description in 'lpfc_mbox_timeout'
 drivers/scsi/lpfc/lpfc_sli.c:8902: warning: Function parameter or member 'mboxq' not described in 'lpfc_sli_issue_mbox_s4'
 drivers/scsi/lpfc/lpfc_sli.c:8902: warning: Excess function parameter 'pmbox' description in 'lpfc_sli_issue_mbox_s4'
 drivers/scsi/lpfc/lpfc_sli.c:9413: warning: Function parameter or member 'piocbq' not described in 'lpfc_sli4_bpl2sgl'
 drivers/scsi/lpfc/lpfc_sli.c:9413: warning: Excess function parameter 'piocb' description in 'lpfc_sli4_bpl2sgl'
 drivers/scsi/lpfc/lpfc_sli.c:9518: warning: Function parameter or member 'iocbq' not described in 'lpfc_sli4_iocb2wqe'
 drivers/scsi/lpfc/lpfc_sli.c:9518: warning: Excess function parameter 'piocb' description in 'lpfc_sli4_iocb2wqe'
 drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'phba' not described in '__lpfc_sli_issue_iocb'
 drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'ring_number' not described in '__lpfc_sli_issue_iocb'
 drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'piocb' not described in '__lpfc_sli_issue_iocb'
 drivers/scsi/lpfc/lpfc_sli.c:10212: warning: Function parameter or member 'flag' not described in '__lpfc_sli_issue_iocb'
 drivers/scsi/lpfc/lpfc_sli.c:10300: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_iocb'
 drivers/scsi/lpfc/lpfc_sli.c:10300: warning: Excess function parameter 'pring' description in 'lpfc_sli_issue_iocb'
 drivers/scsi/lpfc/lpfc_sli.c:11807: warning: Function parameter or member 'cmd' not described in 'lpfc_sli_abort_taskmgmt'
 drivers/scsi/lpfc/lpfc_sli.c:11807: warning: Excess function parameter 'taskmgmt_cmd' description in 'lpfc_sli_abort_taskmgmt'
 drivers/scsi/lpfc/lpfc_sli.c:12067: warning: Function parameter or member 'ring_number' not described in 'lpfc_sli_issue_iocb_wait'
 drivers/scsi/lpfc/lpfc_sli.c:12067: warning: Excess function parameter 'pring' description in 'lpfc_sli_issue_iocb_wait'
 drivers/scsi/lpfc/lpfc_sli.c:12262: warning: Function parameter or member 'mbx_action' not described in 'lpfc_sli_mbox_sys_shutdown'
 drivers/scsi/lpfc/lpfc_sli.c:13219: warning: Function parameter or member 'irspiocbq' not described in 'lpfc_sli4_els_wcqe_to_rspiocbq'
 drivers/scsi/lpfc/lpfc_sli.c:13219: warning: Excess function parameter 'wcqe' description in 'lpfc_sli4_els_wcqe_to_rspiocbq'
 drivers/scsi/lpfc/lpfc_sli.c:13285: warning: Function parameter or member 'mcqe' not described in 'lpfc_sli4_sp_handle_async_event'
 drivers/scsi/lpfc/lpfc_sli.c:13285: warning: Excess function parameter 'cqe' description in 'lpfc_sli4_sp_handle_async_event'
 drivers/scsi/lpfc/lpfc_sli.c:13318: warning: Function parameter or member 'mcqe' not described in 'lpfc_sli4_sp_handle_mbox_event'
 drivers/scsi/lpfc/lpfc_sli.c:13318: warning: Excess function parameter 'cqe' description in 'lpfc_sli4_sp_handle_mbox_event'
 drivers/scsi/lpfc/lpfc_sli.c:13441: warning: Function parameter or member 'cq' not described in 'lpfc_sli4_sp_handle_mcqe'
 drivers/scsi/lpfc/lpfc_sli.c:13768: warning: Function parameter or member 'speq' not described in 'lpfc_sli4_sp_handle_eqe'
 drivers/scsi/lpfc/lpfc_sli.c:14126: warning: Function parameter or member 'cq' not described in 'lpfc_sli4_nvmet_handle_rcqe'
 drivers/scsi/lpfc/lpfc_sli.c:14235: warning: Function parameter or member 'cqe' not described in 'lpfc_sli4_fp_handle_cqe'
 drivers/scsi/lpfc/lpfc_sli.c:14235: warning: Excess function parameter 'eqe' description in 'lpfc_sli4_fp_handle_cqe'
 drivers/scsi/lpfc/lpfc_sli.c:14336: warning: Function parameter or member 'eq' not described in 'lpfc_sli4_hba_handle_eqe'
 drivers/scsi/lpfc/lpfc_sli.c:14808: warning: Function parameter or member 'entry_count' not described in 'lpfc_sli4_queue_alloc'
 drivers/scsi/lpfc/lpfc_sli.c:15185: warning: Function parameter or member 'type' not described in 'lpfc_cq_create'
 drivers/scsi/lpfc/lpfc_sli.c:15185: warning: Function parameter or member 'subtype' not described in 'lpfc_cq_create'
 drivers/scsi/lpfc/lpfc_sli.c:15333: warning: Function parameter or member 'type' not described in 'lpfc_cq_create_set'
 drivers/scsi/lpfc/lpfc_sli.c:15333: warning: Function parameter or member 'subtype' not described in 'lpfc_cq_create_set'
 drivers/scsi/lpfc/lpfc_sli.c:16063: warning: Function parameter or member 'subtype' not described in 'lpfc_rq_create'
 drivers/scsi/lpfc/lpfc_sli.c:16353: warning: Function parameter or member 'subtype' not described in 'lpfc_mrq_create'
 drivers/scsi/lpfc/lpfc_sli.c:16533: warning: Function parameter or member 'phba' not described in 'lpfc_eq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16590: warning: Function parameter or member 'phba' not described in 'lpfc_cq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Function parameter or member 'phba' not described in 'lpfc_mq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Function parameter or member 'mq' not described in 'lpfc_mq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16644: warning: Excess function parameter 'qm' description in 'lpfc_mq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16698: warning: Function parameter or member 'phba' not described in 'lpfc_wq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'phba' not described in 'lpfc_rq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'hrq' not described in 'lpfc_rq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Function parameter or member 'drq' not described in 'lpfc_rq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16754: warning: Excess function parameter 'rq' description in 'lpfc_rq_destroy'
 drivers/scsi/lpfc/lpfc_sli.c:16940: warning: Function parameter or member 'xri' not described in '__lpfc_sli4_free_xri'
 drivers/scsi/lpfc/lpfc_sli.c:16955: warning: Function parameter or member 'xri' not described in 'lpfc_sli4_free_xri'
 drivers/scsi/lpfc/lpfc_sli.c:17002: warning: Function parameter or member 'post_cnt' not described in 'lpfc_sli4_post_sgl_list'
 drivers/scsi/lpfc/lpfc_sli.c:17002: warning: Excess function parameter 'count' description in 'lpfc_sli4_post_sgl_list'
 drivers/scsi/lpfc/lpfc_sli.c:17221: warning: Function parameter or member 'sb_count' not described in 'lpfc_sli4_post_io_sgl_list'
 drivers/scsi/lpfc/lpfc_sli.c:17451: warning: Function parameter or member 'did' not described in 'lpfc_fc_frame_to_vport'
 drivers/scsi/lpfc/lpfc_sli.c:17590: warning: Function parameter or member 'vport' not described in 'lpfc_fc_frame_add'
 drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Function parameter or member 'vport' not described in 'lpfc_sli4_seq_abort_rsp'
 drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Function parameter or member 'aborted' not described in 'lpfc_sli4_seq_abort_rsp'
 drivers/scsi/lpfc/lpfc_sli.c:17817: warning: Excess function parameter 'phba' description in 'lpfc_sli4_seq_abort_rsp'
 drivers/scsi/lpfc/lpfc_sli.c:18060: warning: Function parameter or member 'seq_dmabuf' not described in 'lpfc_prep_seq'
 drivers/scsi/lpfc/lpfc_sli.c:18060: warning: Excess function parameter 'dmabuf' description in 'lpfc_prep_seq'
 drivers/scsi/lpfc/lpfc_sli.c:18332: warning: Function parameter or member 'dmabuf' not described in 'lpfc_sli4_handle_received_buffer'
 drivers/scsi/lpfc/lpfc_sli.c:18655: warning: Function parameter or member 'rpi' not described in '__lpfc_sli4_free_rpi'
 drivers/scsi/lpfc/lpfc_sli.c:18683: warning: Function parameter or member 'rpi' not described in 'lpfc_sli4_free_rpi'
 drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'ndlp' not described in 'lpfc_sli4_resume_rpi'
 drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'cmpl' not described in 'lpfc_sli4_resume_rpi'
 drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Function parameter or member 'arg' not described in 'lpfc_sli4_resume_rpi'
 drivers/scsi/lpfc/lpfc_sli.c:18714: warning: Excess function parameter 'phba' description in 'lpfc_sli4_resume_rpi'
 drivers/scsi/lpfc/lpfc_sli.c:19103: warning: Function parameter or member 'phba' not described in 'lpfc_check_next_fcf_pri_level'
 drivers/scsi/lpfc/lpfc_sli.c:19266: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_rr_index_set'
 drivers/scsi/lpfc/lpfc_sli.c:19295: warning: Function parameter or member 'fcf_index' not described in 'lpfc_sli4_fcf_rr_index_clear'
 drivers/scsi/lpfc/lpfc_sli.c:19331: warning: Function parameter or member 'mbox' not described in 'lpfc_mbx_cmpl_redisc_fcf_table'
 drivers/scsi/lpfc/lpfc_sli.c:20027: warning: Function parameter or member 'pwqeq' not described in 'lpfc_wqe_bpl2sgl'
 drivers/scsi/lpfc/lpfc_sli.c:20027: warning: Excess function parameter 'pwqe' description in 'lpfc_wqe_bpl2sgl'
 drivers/scsi/lpfc/lpfc_sli.c:20141: warning: Function parameter or member 'qp' not described in 'lpfc_sli4_issue_wqe'
 drivers/scsi/lpfc/lpfc_sli.c:20141: warning: Excess function parameter 'ring_number' description in 'lpfc_sli4_issue_wqe'
 drivers/scsi/lpfc/lpfc_sli.c:20434: warning: Function parameter or member 'qp' not described in '_lpfc_move_xri_pbl_to_pvt'
 drivers/scsi/lpfc/lpfc_sli.c:20552: warning: Function parameter or member 'hwqid' not described in 'lpfc_keep_pvt_pool_above_lowwm'
 drivers/scsi/lpfc/lpfc_sli.c:20552: warning: Excess function parameter 'qp' description in 'lpfc_keep_pvt_pool_above_lowwm'
 drivers/scsi/lpfc/lpfc_sli.c:20682: warning: Function parameter or member 'qp' not described in 'lpfc_get_io_buf_from_private_pool'

Link: https://lore.kernel.org/r/20200721164148.2617584-24-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Fix incorrectly named function parameter

Fixes the following W=1 kernel build warning(s):

from  drivers/scsi/qla4xxx/ql4_iocb.c:8:
 drivers/scsi/qla4xxx/ql4_iocb.c:87: warning: Function parameter or member 'mrkr_mod' not described in 'qla4xxx_send_marker_iocb'
 drivers/scsi/qla4xxx/ql4_iocb.c:87: warning: Excess function parameter 'marker_type' description in 'qla4xxx_send_marker_iocb'

Link: https://lore.kernel.org/r/20200721164148.2617584-23-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Fix-up incorrectly documented parameter

Also demote incomplete header from kerneldoc.

Fixes the following W=1 kernel build warning(s):

from  drivers/scsi/qla4xxx/ql4_mbx.c:9:
 drivers/scsi/qla4xxx/ql4_mbx.c:53: warning: Excess function parameter 'ret' description in 'qla4xxx_is_intr_poll_mode'
 drivers/scsi/qla4xxx/ql4_mbx.c:832: warning: Function parameter or member 'fw_ddb_entry_dma' not described in 'qla4xxx_get_fwddb_entry'
 drivers/scsi/qla4xxx/ql4_mbx.c:832: warning: Function parameter or member 'conn_err_detail' not described in 'qla4xxx_get_fwddb_entry'
 drivers/scsi/qla4xxx/ql4_mbx.c:832: warning: Function parameter or member 'tcp_source_port_num' not described in 'qla4xxx_get_fwddb_entry'
 drivers/scsi/qla4xxx/ql4_mbx.c:832: warning: Function parameter or member 'connection_id' not described in 'qla4xxx_get_fwddb_entry'
 drivers/scsi/qla4xxx/ql4_mbx.c:1271: warning: Function parameter or member 'ddb_entry' not described in 'qla4xxx_reset_target'
 drivers/scsi/qla4xxx/ql4_mbx.c:1271: warning: Excess function parameter 'db_entry' description in 'qla4xxx_reset_target'
 drivers/scsi/qla4xxx/ql4_mbx.c:1271: warning: Excess function parameter 'un_entry' description in 'qla4xxx_reset_target'

Link: https://lore.kernel.org/r/20200721164148.2617584-22-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Remove unused variable 'pg_addr'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/lpfc/lpfc_sli.c: In function ‘lpfc_wq_create’:
 drivers/scsi/lpfc/lpfc_sli.c:15810:16: warning: variable ‘pg_addr’ set but not used [-Wunused-but-set-variable]
 15810 | unsigned long pg_addr;
 | ^~~~~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-21-lee.jones@linaro.org
Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Move 'qla4_82xx_reg_tbl' to the only place its used

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/scsi/qla4xxx/ql4_def.h:43,
 from drivers/scsi/qla4xxx/ql4_mbx.c:9:
 drivers/scsi/qla4xxx/ql4_nx.h:602:23: warning: ‘qla4_82xx_reg_tbl’ defined but not used [-Wunused-const-variable=]
 602 | static const uint32_t qla4_82xx_reg_tbl[] = {
 | ^~~~~~~~~~~~~~~~~
 [...]
 NB: Lots of these

Link: https://lore.kernel.org/r/20200721164148.2617584-20-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Remove a bunch of set but unused variables

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_eh_cmd_timed_out’:
 drivers/scsi/qla4xxx/ql4_os.c:1865:24: warning: variable ‘sess’ set but not used [-Wunused-but-set-variable]
 1865 | struct iscsi_session *sess;
 | ^~~~
 drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_session_create’:
 drivers/scsi/qla4xxx/ql4_os.c:3079:19: warning: variable ‘dst_addr’ set but not used [-Wunused-but-set-variable]
 3079 | struct sockaddr *dst_addr;
 | ^~~~~~~~
 drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4_8xxx_iospace_config’:
 drivers/scsi/qla4xxx/ql4_os.c:5512:44: warning: variable ‘db_len’ set but not used [-Wunused-but-set-variable]
 5512 | unsigned long mem_base, mem_len, db_base, db_len;
 | ^~~~~~
 drivers/scsi/qla4xxx/ql4_os.c:5512:35: warning: variable ‘db_base’ set but not used [-Wunused-but-set-variable]
 5512 | unsigned long mem_base, mem_len, db_base, db_len;
 | ^~~~~~~
 drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_get_param_ddb’:
 drivers/scsi/qla4xxx/ql4_os.c:6269:24: warning: variable ‘ha’ set but not used [-Wunused-but-set-variable]
 6269 | struct scsi_qla_host *ha;
 | ^~

Link: https://lore.kernel.org/r/20200721164148.2617584-19-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Fix some function documentation issues

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/pm8001/pm80xx_hwi.c:918: warning: Function parameter or member 'number' not described in 'update_inbnd_queue_table'
 drivers/scsi/pm8001/pm80xx_hwi.c:954: warning: Function parameter or member 'number' not described in 'update_outbnd_queue_table'
 drivers/scsi/pm8001/pm80xx_hwi.c:1717: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_interrupt_enable'
 drivers/scsi/pm8001/pm80xx_hwi.c:1735: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_interrupt_disable'
 drivers/scsi/pm8001/pm80xx_hwi.c:4830: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_start_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4872: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_stop_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'pm8001_ha' not described in 'pm80xx_chip_reg_dev_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'pm8001_dev' not described in 'pm80xx_chip_reg_dev_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'flag' not described in 'pm80xx_chip_reg_dev_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Function parameter or member 'phyId' not described in 'pm80xx_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Function parameter or member 'phy_op' not described in 'pm80xx_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Excess function parameter 'phy_id' description in 'pm80xx_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_isr'
 drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Excess function parameter 'irq' description in 'pm80xx_chip_isr'
 drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Excess function parameter 'stat' description in 'pm80xx_chip_isr'

Link: https://lore.kernel.org/r/20200721164148.2617584-18-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Fix a bunch of kerneldoc issues

Provide lots of missing descriptions, remove some superfluous ones
(probably due to docrot) and demote one header which does not provide many
descriptions, and the ones it does provide are incorrect.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/pm8001/pm8001_hwi.c:339: warning: Function parameter or member 'number' not described in 'update_inbnd_queue_table'
 drivers/scsi/pm8001/pm8001_hwi.c:360: warning: Function parameter or member 'number' not described in 'update_outbnd_queue_table'
 drivers/scsi/pm8001/pm8001_hwi.c:480: warning: Function parameter or member 'interval' not described in 'mpi_set_open_retry_interval_reg'
 drivers/scsi/pm8001/pm8001_hwi.c:1238: warning: Function parameter or member 'int_vec_idx' not described in 'pm8001_chip_msix_interrupt_enable'
 drivers/scsi/pm8001/pm8001_hwi.c:1256: warning: Function parameter or member 'int_vec_idx' not described in 'pm8001_chip_msix_interrupt_disable'
 drivers/scsi/pm8001/pm8001_hwi.c:1270: warning: Function parameter or member 'vec' not described in 'pm8001_chip_interrupt_enable'
 drivers/scsi/pm8001/pm8001_hwi.c:1284: warning: Function parameter or member 'vec' not described in 'pm8001_chip_interrupt_disable'
 drivers/scsi/pm8001/pm8001_hwi.c:4508: warning: Excess function parameter 'num' description in 'pm8001_chip_phy_start_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4544: warning: Excess function parameter 'num' description in 'pm8001_chip_phy_stop_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4564: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_chip_reg_dev_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4564: warning: Function parameter or member 'pm8001_dev' not described in 'pm8001_chip_reg_dev_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4564: warning: Function parameter or member 'flag' not described in 'pm8001_chip_reg_dev_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4624: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_chip_dereg_dev_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4624: warning: Function parameter or member 'device_id' not described in 'pm8001_chip_dereg_dev_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Function parameter or member 'phyId' not described in 'pm8001_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Function parameter or member 'phy_op' not described in 'pm8001_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Excess function parameter 'num' description in 'pm8001_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Excess function parameter 'phy_id' description in 'pm8001_chip_phy_ctl_req'
 drivers/scsi/pm8001/pm8001_hwi.c:4687: warning: Function parameter or member 'vec' not described in 'pm8001_chip_isr'
 drivers/scsi/pm8001/pm8001_hwi.c:4687: warning: Excess function parameter 'irq' description in 'pm8001_chip_isr'
 drivers/scsi/pm8001/pm8001_hwi.c:4687: warning: Excess function parameter 'stat' description in 'pm8001_chip_isr'
 drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_chip_abort_task'
 drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'pm8001_dev' not described in 'pm8001_chip_abort_task'
 drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'task_tag' not described in 'pm8001_chip_abort_task'
 drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'cmd_tag' not described in 'pm8001_chip_abort_task'
 drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Excess function parameter 'task' description in 'pm8001_chip_abort_task'
 drivers/scsi/pm8001/pm8001_hwi.c:4966: warning: Function parameter or member 'tag' not described in 'pm8001_chip_fw_flash_update_build'

Link: https://lore.kernel.org/r/20200721164148.2617584-17-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aic7xxx: Remove set but unused variables 'targ_info' and 'value'

Also remove 'tstate' which became unused after this patch.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aic7xxx/aic79xx_core.c: In function ‘ahd_handle_seqint’:
 drivers/scsi/aic7xxx/aic79xx_core.c:1907:32: warning: variable ‘targ_info’ set but not used [-Wunused-but-set-variable]
 1907 | struct ahd_initiator_tinfo *targ_info;
 | ^~~~~~~~~
 drivers/scsi/pm8001/pm8001_hwi.c: In function ‘mpi_set_phys_g3_with_ssc’:
 drivers/scsi/pm8001/pm8001_hwi.c:413:6: warning: variable ‘value’ set but not used [-Wunused-but-set-variable]
 413 | u32 value, offset, i;
 | ^~~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-16-lee.jones@linaro.org
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Move 'qla4_83xx_reg_tbl' from shared header

'qla4_83xx_reg_tbl' is only used in 'drivers/scsi/qla4xxx/ql4_os.c', move
it there.

Fixes the following W=1 kernel build warning(s):

 In file included from drivers/scsi/qla4xxx/ql4_def.h:46,
 from drivers/scsi/qla4xxx/ql4_init.c:9:
 At top level:
 drivers/scsi/qla4xxx/ql4_83xx.h:90:23: warning: ‘qla4_83xx_reg_tbl’ defined but not used [-Wunused-const-variable=]
 90 | static const uint32_t qla4_83xx_reg_tbl[] = {
 | ^~~~~~~~~~~~~~~~~
 In file included from drivers/scsi/qla4xxx/ql4_def.h:46,
 from drivers/scsi/qla4xxx/ql4_mbx.c:9:
 drivers/scsi/qla4xxx/ql4_83xx.h:90:23: warning: ‘qla4_83xx_reg_tbl’ defined but not used [-Wunused-const-variable=]
 90 | static const uint32_t qla4_83xx_reg_tbl[] = {
 | ^~~~~~~~~~~~~~~~~
 [...]
 NB: Lots of these - snipped for brevity.

Link: https://lore.kernel.org/r/20200721164148.2617584-15-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Check return value of pci_set_mwi()

pci_set_mwi() has 'warn_unused_result' so the result should be checked.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_init.c: In function ‘qla4xxx_pci_config’:
 drivers/scsi/qla4xxx/ql4_init.c:664:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]

And if 'status' is removed:

 drivers/scsi/qla4xxx/ql4_init.c: In function ‘qla4xxx_pci_config’:
 drivers/scsi/qla4xxx/ql4_init.c:666:2: warning: ignoring return value of ‘pci_set_mwi’, declared with attribute warn_unused_result [-Wunused-result]
 666 | pci_set_mwi(ha->pdev);
 | ^~~~~~~~~~~~~~~~~~~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-14-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla4xxx: Remove set but unused variable 'func_number'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/qla4xxx/ql4_init.c: In function ‘ql4xxx_set_mac_number’:
 drivers/scsi/qla4xxx/ql4_init.c:17:10: warning: variable ‘func_number’ set but not used [-Wunused-but-set-variable]

Link: https://lore.kernel.org/r/20200721164148.2617584-13-lee.jones@linaro.org
Cc: QLogic-Storage-Upstream@qlogic.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Add descriptions for unused 'attr' function parameters

Clean-up some whitespace issues too whilst we're here.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/pm8001/pm8001_ctl.c:102: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_fw_version_show'
 drivers/scsi/pm8001/pm8001_ctl.c:331: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_logging_level_show'
 drivers/scsi/pm8001/pm8001_ctl.c:400: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_ib_queue_log_show'
 drivers/scsi/pm8001/pm8001_ctl.c:433: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_ob_queue_log_show'
 drivers/scsi/pm8001/pm8001_ctl.c:464: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_bios_version_show'
 drivers/scsi/pm8001/pm8001_ctl.c:623: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_gsm_log_show'

Link: https://lore.kernel.org/r/20200721164148.2617584-12-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: pm8001: Move function header and supply some missing parameter descriptions

Functions must follow directly after the header that documents them.

Fixes the following W=1 kernel build warning(s):

from  drivers/scsi/pm8001/pm8001_sas.c:41:
inlined from ‘pm8001_issue_ssp_tmf’ at  drivers/scsi/pm8001/pm8001_sas.c:919:2:
 drivers/scsi/pm8001/pm8001_sas.c:379: warning: Function parameter or member 'pm8001_dev' not described in 'DEV_IS_GONE'
 drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'task' description in 'DEV_IS_GONE'
 drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'num' description in 'DEV_IS_GONE'
 drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'gfp_flags' description in 'DEV_IS_GONE'
 drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'is_tmf' description in 'DEV_IS_GONE'
 drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'tmf' description in 'DEV_IS_GONE'
 drivers/scsi/pm8001/pm8001_sas.c:583: warning: Function parameter or member 'device_id' not described in 'pm8001_find_dev'
 drivers/scsi/pm8001/pm8001_sas.c:1000: warning: Function parameter or member 'dev' not described in 'pm8001_I_T_nexus_reset'

Link: https://lore.kernel.org/r/20200721164148.2617584-11-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aic94xx: Fix kerneldoc formatting issue with 'task'

Kerneldoc expects attributes/parameters to be in '@*.: ' format.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aic94xx/aic94xx_tmf.c:685: warning: Function parameter or member 'task' not described in 'asd_query_task'

Link: https://lore.kernel.org/r/20200721164148.2617584-9-lee.jones@linaro.org
Cc: Luben Tuikov <luben_tuikov@adaptec.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Add descriptions for missing parameters

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'p2' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'p3' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'p4' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'p5' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'p6' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'status' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'r1' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'r2' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'r3' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Function parameter or member 'r4' not described in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:203: warning: Excess function parameter 'ret' description in 'src_sync_cmd'
 drivers/scsi/aacraid/src.c:609: warning: Function parameter or member 'dev' not described in 'aac_src_ioremap'
 drivers/scsi/aacraid/src.c:639: warning: Function parameter or member 'dev' not described in 'aac_srcv_ioremap'

Link: https://lore.kernel.org/r/20200721164148.2617584-8-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: "PMC-Sierra, Inc" <aacraid@pmc-sierra.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aic94xx: Fix a couple of kerneldoc formatting issues

Kerneldoc expects attributes/parameters to be in '@*.: ' format.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aic94xx/aic94xx_dev.c:246: warning: Function parameter or member 'dev' not described in 'asd_init_sata_pm_port_ddb'
 drivers/scsi/aic94xx/aic94xx_dev.c:290: warning: Function parameter or member 'dev' not described in 'asd_init_sata_pm_ddb'

Link: https://lore.kernel.org/r/20200721164148.2617584-7-lee.jones@linaro.org
Cc: Luben Tuikov <luben_tuikov@adaptec.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Add missing description for 'dev'

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aacraid/nark.c:31: warning: Function parameter or member 'dev' not described in 'aac_nark_ioremap'

Link: https://lore.kernel.org/r/20200721164148.2617584-6-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: "PMC-Sierra, Inc" <aacraid@pmc-sierra.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Add missing description for 'dev'

And clean-up a couple of whitespace issues while we're here.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aacraid/rkt.c:64: warning: Function parameter or member 'dev' not described in 'aac_rkt_ioremap'

Link: https://lore.kernel.org/r/20200721164148.2617584-5-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: "PMC-Sierra, Inc" <aacraid@pmc-sierra.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aacraid: Add descriptions for missing parameters

Also clean-up some white space issues while we're here.

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'p2' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'p3' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'p4' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'p5' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'p6' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'r1' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'r2' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'r3' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:147: warning: Function parameter or member 'r4' not described in 'sa_sync_cmd'
 drivers/scsi/aacraid/sa.c:290: warning: Function parameter or member 'dev' not described in 'aac_sa_ioremap'

Link: https://lore.kernel.org/r/20200721164148.2617584-4-lee.jones@linaro.org
Cc: Adaptec OEM Raid Solutions <aacraid@microsemi.com>
Cc: "PMC-Sierra, Inc" <aacraid@pmc-sierra.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: aic7xxx: aic79xx_core: Remove a bunch of unused variables

Fixes the following W=1 kernel build warning(s):

 drivers/scsi/aic7xxx/aic79xx_core.c: In function ‘ahd_dump_sglist’:
 drivers/scsi/aic7xxx/aic79xx_core.c:1738:14: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
 1738 | uint32_t len;
 | ^~~
 drivers/scsi/aic7xxx/aic79xx_core.c: In function ‘ahd_handle_seqint’:
 drivers/scsi/aic7xxx/aic79xx_core.c:1911:26: warning: variable ‘tinfo’ set but not used [-Wunused-but-set-variable]
 1911 | struct ahd_transinfo *tinfo;
 | ^~~~~
 drivers/scsi/aic7xxx/aic79xx_core.c: In function ‘ahd_handle_transmission_error’:
 drivers/scsi/aic7xxx/aic79xx_core.c:2672:8: warning: variable ‘lqistat2’ set but not used [-Wunused-but-set-variable]
 2672 | u_int lqistat2;
 | ^~~~~~~~
 drivers/scsi/aic7xxx/aic79xx_core.c: In function ‘ahd_update_pending_scbs’:
 drivers/scsi/aic7xxx/aic79xx_core.c:4221:31: warning: variable ‘tinfo’ set but not used [-Wunused-but-set-variable]
 4221 | struct ahd_initiator_tinfo *tinfo;
 | ^~~~~

Link: https://lore.kernel.org/r/20200721164148.2617584-3-lee.jones@linaro.org
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: arcmsr: arcmsr_hba: Remove statement with no effect

According to LKP, commit 18bc435e0a1d ("scsi: arcmsr: Remove some set but
unused variables") can be furthered to remove the entire statement and not
just the unused variable read into.

Snipped LKP report:

 config: x86_64-randconfig-m001-20200719
 compiler: gcc-9 (Debian 9.3.0-14) 9.3.0

 New smatch warnings:
  drivers/scsi/arcmsr/arcmsr_hba.c:1490 arcmsr_done4abort_postqueue() warn: statement has no effect 8
  drivers/scsi/arcmsr/arcmsr_hba.c:2459 arcmsr_hbaD_postqueue_isr() warn: statement has no effect 8
  drivers/scsi/arcmsr/arcmsr_hba.c:3526 arcmsr_hbaD_polling_ccbdone() warn: statement has no effect 8

 1a4f550a09f89e Nick Cheng  2007-09-13  1401  static void arcmsr_done4abort_postqueue(struct AdapterControlBlock *acb)
 1a4f550a09f89e Nick Cheng  2007-09-13  1402  {
 [...]
 18bc435e0a1de2 Lee Jones   2020-07-13 @1490                             pmu->done_qbuffer[doneq_index & 0xFFF].addressHigh;
                                                                         ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 Delete this line.
 [...]

Link: https://lore.kernel.org/r/20200721164148.2617584-2-lee.jones@linaro.org
Cc: support@areca.com.tw
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: dpt_i2o: Remove superfluous memset()

Fixes coccicheck warning:

./drivers/scsi/dpt_i2o.c:3070:11-29: WARNING:
 dma_alloc_coherent use in sys_tbl already zeroes out memory, so memset is not needed
./drivers/scsi/dpt_i2o.c:2780:10-28: WARNING:
 dma_alloc_coherent use in status already zeroes out memory, so memset is not needed
./drivers/scsi/dpt_i2o.c:2834:20-38: WARNING:
 dma_alloc_coherent use in pHba -> reply_pool already zeroes out memory, so memset is not needed
./drivers/scsi/dpt_i2o.c:1328:10-28: WARNING:
 dma_alloc_coherent use in status already zeroes out memory, so memset is not needed

Link: https://lore.kernel.org/r/20200718123224.1202-1-wanghai38@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: core: Delete unnecessary buffer allocation for every loop iteration

No need to allocate buffer every loop iteration. Allocate buffer once and
reuse it.

Link: https://lore.kernel.org/r/20200717090921.29243-2-yebin10@huawei.com
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: core: Add missing scsi_device_put() in scsi_host_block()

The scsi_host_block() case was missing in commit 4dea170f4fb2 ("scsi: core:
Fix incorrect usage of shost_for_each_device").

Link: https://lore.kernel.org/r/20200717090921.29243-1-yebin10@huawei.com
Fixes: 2bb955840c1d ("scsi: core: add scsi_host_(block,unblock) helper function")
Fixes: 4dea170f4fb2 ("scsi: core: Fix incorrect usage of shost_for_each_device")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: core: Only return started requests from scsi_host_find_tag()

scsi_host_find_tag() is used by the drivers to return a scsi command based
on the command tag. Typically it's used from the interrupt handler to fetch
the command associated with a value returned from hardware. Some drivers
like fnic or qla4xxx, however, also use it also to traverse outstanding
commands.  With the current implementation scsi_host_find_tag() will return
commands even if they are not started (i.e. passed to the driver).  This
will result in random errors with those drivers.  With this patch
scsi_host_find_tag() will only return 'started' commands (i.e. commands
which have been passed to the drivers) thus avoiding the above issue.  The
other use cases will be unaffected as the interrupt handler naturally will
only ever return 'started' requests.

Link: https://lore.kernel.org/r/20200622063022.67891-1-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fcoe: Use eth_zero_addr() to clear mac address

Use eth_zero_addr() to clear mac address insetad of memset().

Link: https://lore.kernel.org/r/1595234344-13955-1-git-send-email-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fnic: Use eth_broadcast_addr() to assign broadcast address

Use eth_broadcast_addr() to assign broadcast address insetad of memset().

Link: https://lore.kernel.org/r/1595233498-13628-1-git-send-email-linmiaohe@huawei.com
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: isci: Remove redundant initialization of variable 'status'

The variable 'status' is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Link: https://lore.kernel.org/r/20200723142614.991416-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")