Ben Chuang [Wed, 7 Apr 2021 09:38:16 +0000 (17:38 +0800)]
mmc: sdhci-pci-gli: Improve GL9763E L1 entry delay to increase battery life
For GL9763E, although there is the best performance at the maximum delay.
Change the value to 20us in order to have better power consumption.
This change may reduce the maximum performance by 10%.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20210407093816.8863-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Nicolas Saenz Julienne [Tue, 6 Apr 2021 10:48:01 +0000 (12:48 +0200)]
dt-bindings: mmc: iproc-sdhci: Convert to json-schema
Convert the brcm,iproc-sdhci binding to DT schema format using json-schema
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210406104802.20898-2-nsaenz@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yang Li [Fri, 2 Apr 2021 09:53:51 +0000 (17:53 +0800)]
mmc: moxart: Remove unused variable 'dma_time' and 'pio_time'
Fixes the following W=1 kernel build warning(s):
drivers/mmc/host/moxart-mmc.c:257:7: warning: variable ‘dma_time’ set
but not used
drivers/mmc/host/moxart-mmc.c:395:7: warning: variable ‘pio_time’ set
but not used
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1617357231-93064-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bean Huo [Fri, 2 Apr 2021 09:24:31 +0000 (11:24 +0200)]
mmc: core: Use userland specified timeout value for eMMC sanitize
As the density increases, the 4-minute timeout value for sanitize is no
longer feasible. At the same time, devices of different densities have
different timeout values, which makes it difficult to use a common timeout
value. Therefore, let's pass down the userland-specified sanitize timeout
value so it can be used.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210402092432.25069-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Wed, 31 Mar 2021 08:17:52 +0000 (11:17 +0300)]
mmc: sdhci-pci: Fix initialization of some SD cards for Intel BYT-based controllers
Bus power may control card power, but the full reset done by SDHCI at
initialization still may not reset the power, whereas a direct write to
SDHCI_POWER_CONTROL can. That might be needed to initialize correctly, if
the card was left powered on previously.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210331081752.23621-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hao Fang [Tue, 30 Mar 2021 06:40:48 +0000 (14:40 +0800)]
mmc: dw_mmc-k3: use the correct HiSilicon copyright
s/Hisilicon/HiSilicon/g.
It should use capital S, according to
https://www.hisilicon.com/en/terms-of-use.
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://lore.kernel.org/r/1617086448-51054-1-git-send-email-fanghao11@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Guo [Fri, 26 Mar 2021 11:02:14 +0000 (19:02 +0800)]
mmc: sdhci-esdhc-imx: separate 100/200 MHz pinctrl states check
As indicated by function esdhc_change_pinstate(), SDR50 and DDR50
require pins_100mhz, while SDR104 and HS400 require pins_200mhz. Some
system design may support SDR50 and DDR50 with 100mhz pin state only
(without 200mhz one). Currently the combined 100/200 MHz pinctrl state
check prevents such system from running SDR50 and DDR50. Separate the
check to support such system design.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210326110214.28416-1-shawnguo@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Al Cooper [Thu, 25 Mar 2021 19:28:34 +0000 (15:28 -0400)]
mmc: sdhci-brcmstb: Remove CQE quirk
Remove the CQHCI_QUIRK_SHORT_TXFR_DESC_SZ quirk because the
latest chips have this fixed and earlier chips have other
CQE problems that prevent the feature from being enabled.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210325192834.42955-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang [Wed, 24 Mar 2021 07:50:13 +0000 (15:50 +0800)]
mmc: sdhci: replace mmc->parent with mmc_dev() for consistency
As pointed out by Ulf, "both "mmc->parent" and mmc_dev(mmc) are being
used in the entire c-file". Convert all the mmc->parent usage in all
sdhci host driver to mmc_dev() for consistency.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210324155013.1e5faa3c@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang [Wed, 24 Mar 2021 07:47:21 +0000 (15:47 +0800)]
mmc: sdhci-of-dwcmshc: set MMC_CAP_WAIT_WHILE_BUSY
The host supports HW busy detection of the device busy signaling over
dat0 line. Set MMC_CAP_wAIT_WHILE_BUSY host capability.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210324154703.69f97fde@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wei Yongjun [Tue, 23 Mar 2021 11:29:56 +0000 (11:29 +0000)]
mmc: sdhci-of-dwcmshc: fix error return code in dwcmshc_probe()
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes:
c2c4da37837e ("mmc: sdhci-of-dwcmshc: add rockchip platform support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210323112956.1016884-1-weiyongjun1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Liming Sun [Mon, 22 Mar 2021 22:46:51 +0000 (18:46 -0400)]
mmc: sdhci-of-dwcmshc: add ACPI support for BlueField-3 SoC
This commit adds ACPI support in the sdhci-of-dwcmshc driver for
BlueField-3 SoC. It has changes to only use the clock hierarchy
for Deviec Tree since the clk is not supported by ACPI. Instead,
ACPI can define 'clock-frequency' which is parsed by existing
sdhci_get_property(). This clock value will be returned in function
dwcmshc_get_max_clock().
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Link: https://lore.kernel.org/r/1616453211-275165-1-git-send-email-limings@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Mon, 22 Mar 2021 05:53:56 +0000 (07:53 +0200)]
mmc: sdhci-pci: Add PCI IDs for Intel LKF
Add PCI IDs for Intel LKF eMMC and SD card host controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210322055356.24923-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Tue, 16 Mar 2021 08:57:17 +0000 (09:57 +0100)]
mmc: tmio: always flag retune when resetting and a card is present
After reset, we manually flagged retune in runtime resume, but missed it
in the workqueue. To fix that and avoid the problem in the future, let's
flag retune in the reset handler directly whenever a card is present.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Takeshi Saito [Tue, 16 Mar 2021 08:57:16 +0000 (09:57 +0100)]
mmc: tmio: restore bus width when resetting
Resetting the IP core will lose the bus width information and not all
code paths recover it. So, make sure the latest bus width gets restored
in the reset routine. For that, tmio_mmc_set_bus_width() is moved, but
not modified.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bean Huo [Fri, 19 Mar 2021 12:13:56 +0000 (13:13 +0100)]
mmc: cavium: Use '"%s...", __func__' to print function name
Use preferred way '"%s...", __func__' to print function name.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20210319121357.255176-2-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
James Young [Thu, 18 Mar 2021 12:40:27 +0000 (12:40 +0000)]
mmc: sdhci-acpi: Add device ID for the AMDI0041 variant of the AMD eMMC controller.
This variant is present on a Lenovo IdeaPad Slim 1, which uses an AMD Dali/Athlon Silver 3050e.
The Windows AMD SD Host Controller driver also lists this as a valid device ID.
Adding this device ID makes the internal eMMC storage on the Lenovo accessible.
Consequently this makes Linux installable and usable on it as well.
Signed-off-by: James Young <james@pocketfluff.org>
Link: https://lore.kernel.org/r/20210318124025.3002861-1-james@pocketfluff.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Seiya Wang [Fri, 19 Mar 2021 02:34:23 +0000 (10:34 +0800)]
dt-bindings: mmc: Add compatible for Mediatek MT8195
This commit adds dt-binding documentation of mmc for Mediatek MT8195 SoC
Platform.
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
Link: https://lore.kernel.org/r/20210319023427.16711-6-seiya.wang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Wed, 17 Mar 2021 09:16:22 +0000 (10:16 +0100)]
mmc: renesas_sdhi: do hard reset if possible
All recent SDHI instances can be reset via the reset controller. If one
is found, use it instead of the open coded reset. This is to get a
future-proof sane reset state.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Wed, 17 Mar 2021 09:16:21 +0000 (10:16 +0100)]
mmc: renesas_sdhi: break SCC reset into own function
renesas_sdhi_reset used to mainly reset the SCC but is now doing more
and even more will be added. So, factor out SCC reset to have a clear
distinction when we want to reset either SCC or SDHI+SCC.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Wed, 17 Mar 2021 09:16:20 +0000 (10:16 +0100)]
mmc: tmio: abort DMA before reset
We will soon allow resetting the whole IP core via a reset controller.
For this case, DMA must be terminated before the actual reset. For the
other cases, it is probably better, too.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Tue, 16 Mar 2021 07:18:22 +0000 (15:18 +0800)]
mmc: sdhci-of-dwcmshc: add rockchip platform support
sdhci based synopsys MMC IP is also used on some rockchip platforms,
so add a basic support here.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/1615879102-45919-3-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Tue, 16 Mar 2021 07:18:21 +0000 (15:18 +0800)]
dt-bindings: mmc: sdhci-of-dwcmhsc: Add rockchip support
This patch adds rockchip support in sdhci-of-dwcmhsc.yaml
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/1615879102-45919-2-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Tue, 16 Mar 2021 07:18:20 +0000 (15:18 +0800)]
dt-bindings: mmc: sdhci-of-dwcmhsc: Convert to yaml file
This patch converts sdhci-of-dwcmshc.txt to sdhci-of-dwcmshc.yaml
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1615879102-45919-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fabio Estevam [Sun, 14 Mar 2021 23:08:24 +0000 (20:08 -0300)]
mmc: sdhci-esdhc-imx: Use device_get_match_data()
The retrieval of driver data can be a bit simplified by using
device_get_match_data(), so switch to it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210314230824.148969-2-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fabio Estevam [Sun, 14 Mar 2021 23:08:23 +0000 (20:08 -0300)]
mmc: sdhci-esdhc-imx: Remove non-DT stub
i.MX has been converted to a devicetree only platform, so remove
the non-DT stub for sdhci_esdhc_imx_probe_dt().
Also, make the driver depend on OF now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210314230824.148969-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Joey Pabalan [Sat, 13 Mar 2021 17:37:40 +0000 (12:37 -0500)]
memstick: Remove useless else branch
Remove else branch on line 334 of memstick.c, after the return of the
previous branch. Found by checkpatch.
Signed-off-by: Joey Pabalan <jpabalanb@gmail.com>
Link: https://lore.kernel.org/r/20210313173740.GA580681@joeylaptop
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Wed, 10 Mar 2021 15:29:00 +0000 (16:29 +0100)]
mmc: core: Fix hanging on I/O during system suspend for removable cards
The mmc core uses a PM notifier to temporarily during system suspend, turn
off the card detection mechanism for removal/insertion of (e)MMC/SD/SDIO
cards. Additionally, the notifier may be used to remove an SDIO card
entirely, if a corresponding SDIO functional driver don't have the system
suspend/resume callbacks assigned. This behaviour has been around for a
very long time.
However, a recent bug report tells us there are problems with this
approach. More precisely, when receiving the PM_SUSPEND_PREPARE
notification, we may end up hanging on I/O to be completed, thus also
preventing the system from getting suspended.
In the end what happens, is that the cancel_delayed_work_sync() in
mmc_pm_notify() ends up waiting for mmc_rescan() to complete - and since
mmc_rescan() wants to claim the host, it needs to wait for the I/O to be
completed first.
Typically, this problem is triggered in Android, if there is ongoing I/O
while the user decides to suspend, resume and then suspend the system
again. This due to that after the resume, an mmc_rescan() work gets punted
to the workqueue, which job is to verify that the card remains inserted
after the system has resumed.
To fix this problem, userspace needs to become frozen to suspend the I/O,
prior to turning off the card detection mechanism. Therefore, let's drop
the PM notifiers for mmc subsystem altogether and rely on the card
detection to be turned off/on as a part of the system_freezable_wq, that we
are already using.
Moreover, to allow and SDIO card to be removed during system suspend, let's
manage this from a ->prepare() callback, assigned at the mmc_host_class
level. In this way, we can use the parent device (the mmc_host_class
device), to remove the card device that is the child, in the
device_prepare() phase.
Reported-by: Kiwoong Kim <kwmad.kim@samsung.com>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210310152900.149380-1-ulf.hansson@linaro.org
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Jisheng Zhang [Thu, 11 Mar 2021 09:41:57 +0000 (17:41 +0800)]
mmc: sdio: fix a typo in the comment of SDIO_SD_REV_3_00
I believe "Spev" is typo, should be "Spec".
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20210311174157.561dada9@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang [Thu, 11 Mar 2021 09:40:46 +0000 (17:40 +0800)]
mmc: sdhci: Use "mmc" directly rather than "host->mmc"
Clean up the code to use the "mmc" directly instead of "host->mmc".
If the code sits in hot code path, this clean up also brings trvial
performance improvement. Take the sdhci_post_req() for example:
before the patch:
...
8d0:
a9be7bfd stp x29, x30, [sp, #-32]!
8d4:
910003fd mov x29, sp
8d8:
f9000bf3 str x19, [sp, #16]
8dc:
f9400833 ldr x19, [x1, #16]
8e0:
b9404261 ldr w1, [x19, #64]
8e4:
34000161 cbz w1, 910 <sdhci_post_req+0x50>
8e8:
f9424400 ldr x0, [x0, #1160]
8ec:
d2800004 mov x4, #0x0 // #0
8f0:
b9401a61 ldr w1, [x19, #24]
8f4:
b9403262 ldr w2, [x19, #48]
8f8:
f9400000 ldr x0, [x0]
8fc:
f278003f tst x1, #0x100
900:
f9401e61 ldr x1, [x19, #56]
904:
1a9f17e3 cset w3, eq // eq = none
908:
11000463 add w3, w3, #0x1
90c:
94000000 bl 0 <dma_unmap_sg_attrs>
...
After the patch:
...
8d0:
a9be7bfd stp x29, x30, [sp, #-32]!
8d4:
910003fd mov x29, sp
8d8:
f9000bf3 str x19, [sp, #16]
8dc:
f9400833 ldr x19, [x1, #16]
8e0:
b9404261 ldr w1, [x19, #64]
8e4:
34000141 cbz w1, 90c <sdhci_post_req+0x4c>
8e8:
b9401a61 ldr w1, [x19, #24]
8ec:
d2800004 mov x4, #0x0 // #0
8f0:
b9403262 ldr w2, [x19, #48]
8f4:
f9400000 ldr x0, [x0]
8f8:
f278003f tst x1, #0x100
8fc:
f9401e61 ldr x1, [x19, #56]
900:
1a9f17e3 cset w3, eq // eq = none
904:
11000463 add w3, w3, #0x1
908:
94000000 bl 0 <dma_unmap_sg_attrs>
...
We saved one ldr instruction: "ldr x0, [x0, #1160]"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210311174046.597d1951@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jisheng Zhang [Thu, 11 Mar 2021 10:14:32 +0000 (18:14 +0800)]
mmc: sdhci-pci: Avoid comma separated statements
Use semicolons.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210311181432.6385cd2b@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yang Li [Tue, 9 Mar 2021 06:47:58 +0000 (14:47 +0800)]
mmc: via-sdmmc: remove unneeded variable 'ret'
Fix the following coccicheck warning:
./drivers/mmc/host/via-sdmmc.c:1274:5-8: Unneeded variable: "ret".
Return "0" on line 1295
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1615272478-52458-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Philipp Zabel [Fri, 5 Mar 2021 09:07:24 +0000 (10:07 +0100)]
mmc: dw_mmc: simplify optional reset handling
As of commit
bb475230b8e5 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210305090724.18832-1-p.zabel@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Philipp Zabel [Fri, 5 Mar 2021 09:08:27 +0000 (10:08 +0100)]
mmc: sdhci-st: simplify optional reset handling
As of commit
bb475230b8e5 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20210305090827.19124-1-p.zabel@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jia-Ju Bai [Fri, 5 Mar 2021 02:14:45 +0000 (18:14 -0800)]
memstick: core: Assign error code of mspro_block_resume()
When mspro_block_init_card() fails, no error return code of
mspro_block_resume() is assigned/propagated. Let's fix this.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20210305021445.3435-1-baijiaju1990@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Luca Porzio [Mon, 15 Feb 2021 00:32:18 +0000 (01:32 +0100)]
mmc: core: Remove mq->use_cqe from the struct mmc_queue
The host->cqe_enabled is already containing the needed information about
whether the CQE is enabled or not, hence there is no need to keep another
copy of it around.
Signed-off-by: Luca Porzio <lporzio@micron.com>
Signed-off-by: Zhan Liu <zliua@micron.com>
Link: https://lore.kernel.org/r/20210215003217.GA12240@lupo-laptop
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Wed, 3 Mar 2021 12:20:49 +0000 (13:20 +0100)]
mmc: block: Fix error path in mmc_blk_probe()
Returning zero to indicate success, when we actually have failed to probe
is wrong. As a matter of fact, it leads to that mmc_blk_remove() gets
called at a card removal and then triggers "NULL pointer dereference"
splats. This is because mmc_blk_remove() relies on data structures and
pointers to be setup from mmc_blk_probe(), of course.
There have been no errors reported about this, which is most likely because
mmc_blk_probe() never fails like this. Nevertheless, let's fix the code by
propagating the error codes correctly and prevent us from leaking memory by
calling also destroy_workqueue() in the error path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210303122049.151986-4-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Wed, 3 Mar 2021 12:20:48 +0000 (13:20 +0100)]
mmc: block: Simplify logging during probe about added partitions
To simplify the code, move the logging into the common mmc_blk_alloc_req()
and drop the rather useless information about the partition type/id.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210303122049.151986-3-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Wed, 3 Mar 2021 12:20:47 +0000 (13:20 +0100)]
mmc: block: Drop use of unlikely() in mmc_blk_probe()
mmc_blk_probe() isn't a hotpath, which makes it's questionable to use
unlikely(). Therefore let's simply drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210303122049.151986-2-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Thu, 4 Mar 2021 09:29:03 +0000 (10:29 +0100)]
mmc: renesas_sdhi: use custom mask for TMIO_MASK_ALL
Populate the new member for custom mask values to make sure this value
is applied whenever needed. Also, rename the define holding the value
because this is not only about initialization anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210304092903.8534-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pradeep P V K [Wed, 3 Mar 2021 08:32:11 +0000 (14:02 +0530)]
mmc: sdhci: Check for reset prior to DMA address unmap
For data read commands, SDHC may initiate data transfers even before it
completely process the command response. In case command itself fails,
driver un-maps the memory associated with data transfer but this memory
can still be accessed by SDHC for the already initiated data transfer.
This scenario can lead to un-mapped memory access error.
To avoid this scenario, reset SDHC (when command fails) prior to
un-mapping memory. Resetting SDHC ensures that all in-flight data
transfers are either aborted or completed. So we don't run into this
scenario.
Swap the reset, un-map steps sequence in sdhci_request_done().
Suggested-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Pradeep P V K <pragalla@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1614760331-43499-1-git-send-email-pragalla@qti.qualcomm.com
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dinghao Liu [Fri, 26 Feb 2021 08:41:46 +0000 (16:41 +0800)]
mmc: sdhci-pci-o2micro: Add missing checks in sdhci_pci_o2_probe
It's odd to adopt different error handling on failure of
pci_read_config_dword(). Check the return value and terminate
execution flow on failure of all pci_read_config_dword() calls
in this function.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210226084146.29095-1-dinghao.liu@zju.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renius Chen [Thu, 25 Feb 2021 11:13:07 +0000 (19:13 +0800)]
mmc: sdhci-pci-gli: Enable short circuit protection mechanism of GL9755
Short circuit protection mechanism of GL9755 is disabled by HW default
setting. Enable short circuit protection to prevent GL9755 from being
damaged by short circuit or over current.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210225111307.62975-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peng Fan [Thu, 25 Feb 2021 03:10:04 +0000 (11:10 +0800)]
mmc: sdhci-esdhc-imx: validate pinctrl before use it
When imx_data->pinctrl is not a valid pointer, pinctrl_lookup_state
will trigger kernel panic.
When we boot Dual OS on Jailhouse hypervisor, we let the 1st Linux to
configure pinmux ready for the 2nd OS, so the 2nd OS not have pinctrl
settings.
Similar to this commit
b62eee9f804e ("mmc: sdhci-esdhc-imx: no fail when no pinctrl available").
Reviewed-by: Bough Chen <haobo.chen@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1614222604-27066-6-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peng Fan [Thu, 25 Feb 2021 03:10:03 +0000 (11:10 +0800)]
dt-bindings: mmc: fsl-imx-esdhc: add clock bindings
Add clock bindings for fsl-imx-esdhc yaml
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1614222604-27066-5-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Peng Fan [Thu, 25 Feb 2021 03:10:00 +0000 (11:10 +0800)]
dt-bindings: mmc: fsl-imx-esdhc: add pinctrl bindings
Add pinctrl bindings for fsl-imx-esdhc yaml
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1614222604-27066-2-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Tue, 23 Feb 2021 10:08:29 +0000 (11:08 +0100)]
mmc: tmio: support custom irq masks
SDHI Gen2+ has a different value for TMIO_MASK_ALL, so add a member to
support that. If the member is not used, the previous default value is
applied.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210223100830.25125-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Seunghui Lee [Mon, 22 Feb 2021 08:31:56 +0000 (17:31 +0900)]
mmc: core: Set read only for SD cards with permanent write protect bit
Some of SD cards sets permanent write protection bit in their CSD register,
due to lifespan or internal problem. To avoid unnecessary I/O write
operations, let's parse the bits in the CSD during initialization and mark
the card as read only for this case.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20210222083156.19158-1-sh043.lee@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christophe JAILLET [Sat, 20 Feb 2021 14:29:53 +0000 (15:29 +0100)]
mmc: uniphier-sd: Fix a resource leak in the remove function
A 'tmio_mmc_host_free()' call is missing in the remove function, in order
to balance a 'tmio_mmc_host_alloc()' call in the probe.
This is done in the error handling path of the probe, but not in the remove
function.
Add the missing call.
Fixes:
3fd784f745dd ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142953.918608-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christophe JAILLET [Sat, 20 Feb 2021 14:29:35 +0000 (15:29 +0100)]
mmc: uniphier-sd: Fix an error handling path in uniphier_sd_probe()
A 'uniphier_sd_clk_enable()' call should be balanced by a corresponding
'uniphier_sd_clk_disable()' call.
This is done in the remove function, but not in the error handling path of
the probe.
Add the missing call.
Fixes:
3fd784f745dd ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142935.918554-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Thu, 18 Feb 2021 11:02:24 +0000 (12:02 +0100)]
mmc: tmio: remove workaround for NON_REMOVABLE
RPM handling has been improved twice since this comment, and also SCC
handling has been improved a lot. All the testing we did (Geert's and
Niklas' and Wolfram's board farms) with the workaround removed did not
lead to problems, so it is time to get rid of it to the best of our
knowledge.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210218110224.6910-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Yue Hu [Mon, 15 Feb 2021 01:51:16 +0000 (09:51 +0800)]
mmc: core: Reduce code duplication to mmc_spi_send_{csd|cid}
mmc_spi_send_{csd|cid} have similar function body. Let's remove the
duplicated part to simplify the code, just add opcode to distinguish
them in changed mmc_spi_send_cxd().
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210215015116.1355-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Wed, 3 Feb 2021 18:42:29 +0000 (19:42 +0100)]
mmc: dw_mmc: Drop redundant call to ->card_event callback
The ->card_event callback isn't being used by any of the dw_mmc variants.
It's likely a leftover from an earlier change, hence let's just drop the
redundant call to it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Ulf Hansson [Fri, 12 Feb 2021 13:16:10 +0000 (14:16 +0100)]
mmc: core: Drop reference counting of the bus_ops
When the mmc_rescan work is enabled for execution (host->rescan_disable),
it's the only instance per mmc host that is allowed to set/clear the
host->bus_ops pointer.
Besides the mmc_rescan work, there are a couple of scenarios when the
host->bus_ops pointer may be accessed. Typically, those can be described as
as below:
*)
Upper mmc driver layers (like the mmc block device driver or an SDIO
functional driver) needs to execute a host->bus_ops callback. This can be
considered as safe without having to use some special locking mechanism,
because they operate on top of the struct mmc_card. As long as there is a
card to operate upon, the mmc core guarantees that there is a host->bus_ops
assigned as well. Note that, upper layer mmc drivers are of course
responsible to clean up from themselves from their ->remove() callbacks,
otherwise things would fall apart anyways.
**)
Via the mmc host instance, we may need to force a removal of an inserted
mmc card. This happens when a mmc host driver gets unbind, for example. In
this case, we protect the host->bus_ops pointer from concurrent accesses,
by disabling the mmc_rescan work upfront (host->rescan_disable). See
mmc_stop_host() for example.
This said, it seems like the reference counting of the host->bus_ops
pointer at some point have become superfluous. As this is an old mechanism
of the mmc core, it a bit difficult to digest the history of when that
could have happened. However, let's drop the reference counting to avoid
unnecessary code-paths and lockings.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210212131610.236843-1-ulf.hansson@linaro.org
Ulf Hansson [Fri, 12 Feb 2021 13:15:32 +0000 (14:15 +0100)]
mmc: core: Drop superfluous validations in mmc_hw|sw_reset()
The mmc_hw|sw_reset() APIs are designed to be called solely from upper
layers, which means drivers that operates on top of the struct mmc_card,
like the mmc block device driver and an SDIO functional driver.
Additionally, as long as the struct mmc_host has a valid pointer to a
struct mmc_card, the corresponding host->bus_ops pointer stays valid and
assigned.
For these reasons, let's drop the superfluous reference counting and the
redundant validations in mmc_hw|sw_reset().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210212131532.236775-1-ulf.hansson@linaro.org
DooHyun Hwang [Wed, 10 Feb 2021 04:59:36 +0000 (13:59 +0900)]
mmc: core: Do a power cycle when the CMD11 fails
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com>
Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds [Sun, 28 Mar 2021 22:48:16 +0000 (15:48 -0700)]
Linux 5.12-rc5
Linus Torvalds [Sun, 28 Mar 2021 20:22:54 +0000 (13:22 -0700)]
Merge tag 'perf-tools-fixes-for-v5.12-2020-03-28' of git://git./linux/kernel/git/acme/linux
Pull perf tooling fixes from Arnaldo Carvalho de Melo:
- Avoid write of uninitialized memory when generating PERF_RECORD_MMAP*
records.
- Fix 'perf top' BPF support related crash with perf_event_paranoid=3 +
kptr_restrict.
- Validate raw event with sysfs exported format bits.
- Fix waipid on SIGCHLD delivery bugs in 'perf daemon'.
- Change to use bash for daemon test on Debian, where the default is
dash and thus fails for use of bashisms in this test.
- Fix memory leak in vDSO found using ASAN.
- Remove now useless (due to the fact that BPF now supports static
vars) failing sub test "BPF relocation checker".
- Fix auxtrace queue conflict.
- Sync linux/kvm.h with the kernel sources.
* tag 'perf-tools-fixes-for-v5.12-2020-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf test: Change to use bash for daemon test
perf record: Fix memory leak in vDSO found using ASAN
perf test: Remove now useless failing sub test "BPF relocation checker"
perf daemon: Return from kill functions
perf daemon: Force waipid for all session on SIGCHLD delivery
perf top: Fix BPF support related crash with perf_event_paranoid=3 + kptr_restrict
perf pmu: Validate raw event with sysfs exported format bits
perf synthetic events: Avoid write of uninitialized memory when generating PERF_RECORD_MMAP* records
tools headers UAPI: Sync linux/kvm.h with the kernel sources
perf synthetic-events: Fix uninitialized 'kernel_thread' variable
perf auxtrace: Fix auxtrace queue conflict
Linus Torvalds [Sun, 28 Mar 2021 20:20:38 +0000 (13:20 -0700)]
Merge tag 'auxdisplay-for-linus-v5.12-rc6' of git://github.com/ojeda/linux
Pull auxdisplay fix from Miguel Ojeda:
"Remove in_interrupt() usage (Sebastian Andrzej Siewior)"
* tag 'auxdisplay-for-linus-v5.12-rc6' of git://github.com/ojeda/linux:
auxdisplay: Remove in_interrupt() usage.
Linus Torvalds [Sun, 28 Mar 2021 19:19:16 +0000 (12:19 -0700)]
Merge tag 'x86-urgent-2021-03-28' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two fixes:
- Fix build failure on Ubuntu with new GCC packages that turn
on -fcf-protection
- Fix SME memory encryption PTE encoding bug - AFAICT the code
worked on 4K page sizes (level 1) but had the wrong shift at
higher page level orders (level 2 and higher)"
* tag 'x86-urgent-2021-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/build: Turn off -fcf-protection for realmode targets
x86/mem_encrypt: Correct physical address calculation in __set_clr_pte_enc()
Linus Torvalds [Sun, 28 Mar 2021 19:12:22 +0000 (12:12 -0700)]
Merge tag 'locking-urgent-2021-03-28' of git://git./linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"Fix the non-debug mutex_lock_io_nested() method to map to
mutex_lock_io() instead of mutex_lock().
Right now nothing uses this API explicitly, but this is an
accident waiting to happen"
* tag 'locking-urgent-2021-03-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/mutex: Fix non debug version of mutex_lock_io_nested()
Linus Torvalds [Sun, 28 Mar 2021 19:06:21 +0000 (12:06 -0700)]
Merge tag '5.12-rc4-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five cifs/smb3 fixes, two for stable.
Includes an important fix for encryption and an ACL fix, as well as a
fix for possible reflink data corruption"
* tag '5.12-rc4-smb3' of git://git.samba.org/sfrench/cifs-2.6:
smb3: fix cached file size problems in duplicate extents (reflink)
cifs: Silently ignore unknown oplock break handle
cifs: revalidate mapping when we open files for SMB1 POSIX
cifs: Fix chmod with modefromsid when an older ACE already exists.
cifs: Adjust key sizes and key generation routines for AES256 encryption
Linus Torvalds [Sun, 28 Mar 2021 18:42:05 +0000 (11:42 -0700)]
Merge tag 'io_uring-5.12-2021-03-27' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Use thread info versions of flag testing, as discussed last week.
- The series enabling PF_IO_WORKER to just take signals, instead of
needing to special case that they do not in a bunch of places. Ends
up being pretty trivial to do, and then we can revert all the special
casing we're currently doing.
- Kill dead pointer assignment
- Fix hashed part of async work queue trace
- Fix sign extension issue for IORING_OP_PROVIDE_BUFFERS
- Fix a link completion ordering regression in this merge window
- Cancellation fixes
* tag 'io_uring-5.12-2021-03-27' of git://git.kernel.dk/linux-block:
io_uring: remove unsued assignment to pointer io
io_uring: don't cancel extra on files match
io_uring: don't cancel-track common timeouts
io_uring: do post-completion chore on t-out cancel
io_uring: fix timeout cancel return code
Revert "signal: don't allow STOP on PF_IO_WORKER threads"
Revert "kernel: freezer should treat PF_IO_WORKER like PF_KTHREAD for freezing"
Revert "kernel: treat PF_IO_WORKER like PF_KTHREAD for ptrace/signals"
Revert "signal: don't allow sending any signals to PF_IO_WORKER threads"
kernel: stop masking signals in create_io_thread()
io_uring: handle signals for IO threads like a normal thread
kernel: don't call do_exit() for PF_IO_WORKER threads
io_uring: maintain CQE order of a failed link
io-wq: fix race around pending work on teardown
io_uring: do ctx sqd ejection in a clear context
io_uring: fix provide_buffers sign extension
io_uring: don't skip file_end_write() on reissue
io_uring: correct io_queue_async_work() traces
io_uring: don't use {test,clear}_tsk_thread_flag() for current
Linus Torvalds [Sun, 28 Mar 2021 18:37:42 +0000 (11:37 -0700)]
Merge tag 'block-5.12-2021-03-27' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Fix regression from this merge window with the xarray partition
change, which allowed partition counts that overflow the u8 that
holds the partition number (Ming)
- Fix zone append warning (Johannes)
- Segmentation count fix for multipage bvecs (David)
- Partition scan fix (Chris)
* tag 'block-5.12-2021-03-27' of git://git.kernel.dk/linux-block:
block: don't create too many partitions
block: support zone append bvecs
block: recalculate segment count for multi-segment discards correctly
block: clear GD_NEED_PART_SCAN later in bdev_disk_changed
Linus Torvalds [Sun, 28 Mar 2021 18:34:47 +0000 (11:34 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes, all in drivers (qla2xxx, mkt3sas, qedi, target,
ibmvscsi).
The most serious are the target pscsi oom and the qla2xxx revert which
can otherwise cause a use after free"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: pscsi: Clean up after failure in pscsi_map_sg()
scsi: target: pscsi: Avoid OOM in pscsi_map_sg()
scsi: mpt3sas: Fix error return code of mpt3sas_base_attach()
scsi: qedi: Fix error return code of qedi_alloc_global_queues()
scsi: Revert "qla2xxx: Make sure that aborted commands are freed"
scsi: ibmvfc: Make ibmvfc_wait_for_ops() MQ aware
scsi: ibmvfc: Fix potential race in ibmvfc_wait_for_ops()
Colin Ian King [Fri, 26 Mar 2021 19:52:51 +0000 (19:52 +0000)]
io_uring: remove unsued assignment to pointer io
There is an assignment to io that is never read after the assignment,
the assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Thu, 25 Mar 2021 18:32:45 +0000 (18:32 +0000)]
io_uring: don't cancel extra on files match
As tasks always wait and kill their io-wq on exec/exit, files are of no
more concern to us, so we don't need to specifically cancel them by hand
in those cases. Moreover we should not, because io_match_task() looks at
req->task->files now, which is always true and so leads to extra
cancellations, that wasn't a case before per-task io-wq.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/0566c1de9b9dd417f5de345c817ca953580e0e2e.1616696997.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Thu, 25 Mar 2021 18:32:44 +0000 (18:32 +0000)]
io_uring: don't cancel-track common timeouts
Don't account usual timeouts (i.e. not linked) as REQ_F_INFLIGHT but
keep behaviour prior to
dd59a3d595cc1 ("io_uring: reliably cancel linked
timeouts").
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/104441ef5d97e3932113d44501fda0df88656b83.1616696997.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Thu, 25 Mar 2021 18:32:43 +0000 (18:32 +0000)]
io_uring: do post-completion chore on t-out cancel
Don't forget about io_commit_cqring() + io_cqring_ev_posted() after
exit/exec cancelling timeouts. Both functions declared only after
io_kill_timeouts(), so to avoid tons of forward declarations move
it down.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/72ace588772c0f14834a6a4185d56c445a366fb4.1616696997.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Thu, 25 Mar 2021 18:32:42 +0000 (18:32 +0000)]
io_uring: fix timeout cancel return code
When we cancel a timeout we should emit a sensible return code, like
-ECANCELED but not 0, otherwise it may trick users.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/7b0ad1065e3bd1994722702bd0ba9e7bc9b0683b.1616696997.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Mar 2021 00:23:44 +0000 (18:23 -0600)]
Revert "signal: don't allow STOP on PF_IO_WORKER threads"
This reverts commit
4db4b1a0d1779dc159f7b87feb97030ec0b12597.
The IO threads allow and handle SIGSTOP now, so don't special case them
anymore in task_set_jobctl_pending().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Mar 2021 00:22:11 +0000 (18:22 -0600)]
Revert "kernel: freezer should treat PF_IO_WORKER like PF_KTHREAD for freezing"
This reverts commit
15b2219facadec583c24523eed40fa45865f859f.
Before IO threads accepted signals, the freezer using take signals to wake
up an IO thread would cause them to loop without any way to clear the
pending signal. That is no longer the case, so stop special casing
PF_IO_WORKER in the freezer.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Mar 2021 00:18:59 +0000 (18:18 -0600)]
Revert "kernel: treat PF_IO_WORKER like PF_KTHREAD for ptrace/signals"
This reverts commit
6fb8f43cede0e4bd3ead847de78d531424a96be9.
The IO threads do allow signals now, including SIGSTOP, and we can allow
ptrace attach. Attaching won't reveal anything interesting for the IO
threads, but it will allow eg gdb to attach to a task with io_urings
and IO threads without complaining. And once attached, it will allow
the usual introspection into regular threads.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Mar 2021 00:18:15 +0000 (18:18 -0600)]
Revert "signal: don't allow sending any signals to PF_IO_WORKER threads"
This reverts commit
5be28c8f85ce99ed2d329d2ad8bdd18ea19473a5.
IO threads now take signals just fine, so there's no reason to limit them
specifically. Revert the change that prevented that from happening.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Mar 2021 15:05:22 +0000 (09:05 -0600)]
kernel: stop masking signals in create_io_thread()
This is racy - move the blocking into when the task is created and
we're marking it as PF_IO_WORKER anyway. The IO threads are now
prepared to handle signals like SIGSTOP as well, so clear that from
the mask to allow proper stopping of IO threads.
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Mar 2021 00:16:06 +0000 (18:16 -0600)]
io_uring: handle signals for IO threads like a normal thread
We go through various hoops to disallow signals for the IO threads, but
there's really no reason why we cannot just allow them. The IO threads
never return to userspace like a normal thread, and hence don't go through
normal signal processing. Instead, just check for a pending signal as part
of the work loop, and call get_signal() to handle it for us if anything
is pending.
With that, we can support receiving signals, including special ones like
SIGSTOP.
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Sat, 27 Mar 2021 07:13:09 +0000 (15:13 +0800)]
block: don't create too many partitions
Commit
a33df75c6328 ("block: use an xarray for disk->part_tbl") drops the
check on max supported number of partitionsr, and allows partition with
bigger partition numbers to be added. However, ->bd_partno is defined as
u8, so partition index of xarray table may not match with ->bd_partno.
Then delete_partition() may delete one unmatched partition, and caused
use-after-free.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: syzbot+8fede7e30c7cee0de139@syzkaller.appspotmail.com
Fixes:
a33df75c6328 ("block: use an xarray for disk->part_tbl")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Steve French [Fri, 26 Mar 2021 23:41:55 +0000 (18:41 -0500)]
smb3: fix cached file size problems in duplicate extents (reflink)
There were two problems (one of which could cause data corruption)
that were noticed with duplicate extents (ie reflink)
when debugging why various xfstests were being incorrectly skipped
(e.g. generic/138, generic/140, generic/142). First, we were not
updating the file size locally in the cache when extending a
file due to reflink (it would refresh after actimeo expires)
but xfstest was checking the size immediately which was still
0 so caused the test to be skipped. Second, we were setting
the target file size (which could shrink the file) in all cases
to the end of the reflinked range rather than only setting the
target file size when reflink would extend the file.
CC: <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Vincent Whitchurch [Fri, 19 Mar 2021 13:57:11 +0000 (14:57 +0100)]
cifs: Silently ignore unknown oplock break handle
Make SMB2 not print out an error when an oplock break is received for an
unknown handle, similar to SMB1. The debug message which is printed for
these unknown handles may also be misleading, so fix that too.
The SMB2 lease break path is not affected by this patch.
Without this, a program which writes to a file from one thread, and
opens, reads, and writes the same file from another thread triggers the
below errors several times a minute when run against a Samba server
configured with "smb2 leases = no".
CIFS: VFS: \\192.168.0.1 No task to wake, unknown frame received! NumMids 2
00000000:
424d53fe 00000040 00000000 00000012 .SMB@...........
00000010:
00000001 00000000 ffffffff ffffffff ................
00000020:
00000000 00000000 00000000 00000000 ................
00000030:
00000000 00000000 00000000 00000000 ................
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Ronnie Sahlberg [Thu, 25 Mar 2021 06:26:35 +0000 (16:26 +1000)]
cifs: revalidate mapping when we open files for SMB1 POSIX
RHBZ: 1933527
Under SMB1 + POSIX, if an inode is reused on a server after we have read and
cached a part of a file, when we then open the new file with the
re-cycled inode there is a chance that we may serve the old data out of cache
to the application.
This only happens for SMB1 (deprecated) and when posix are used.
The simplest solution to avoid this race is to force a revalidate
on smb1-posix open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Shyam Prasad N [Fri, 26 Mar 2021 10:28:16 +0000 (10:28 +0000)]
cifs: Fix chmod with modefromsid when an older ACE already exists.
My recent fixes to cifsacl to maintain inherited ACEs had
regressed modefromsid when an older ACL already exists.
Found testing xfstest 495 with modefromsid mount option
Fixes:
f5065508897a ("cifs: Retain old ACEs when converting between mode bits and ACL")
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Jens Axboe [Fri, 26 Mar 2021 14:57:10 +0000 (08:57 -0600)]
kernel: don't call do_exit() for PF_IO_WORKER threads
Right now we're never calling get_signal() from PF_IO_WORKER threads, but
in preparation for doing so, don't handle a fatal signal for them. The
workers have state they need to cleanup when exiting, so just return
instead of calling do_exit() on their behalf. The threads themselves will
detect a fatal signal and do proper shutdown.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 26 Mar 2021 19:21:05 +0000 (12:21 -0700)]
Merge tag 'for-5.12/dm-fixes-2' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM verity target's optional argument processing.
- Fix DM core's zoned model and zone sectors checks.
- Fix spurious "detected capacity change" pr_info() when creating new
DM device.
- Fix DM ioctl out of bounds array access in handling of
DM_LIST_DEVICES_CMD when no devices exist.
* tag 'for-5.12/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm ioctl: fix out of bounds array access when no devices
dm: don't report "detected capacity change" on device creation
dm table: Fix zoned model check and zone sectors check
dm verity: fix DM_VERITY_OPTS_MAX value
Mikulas Patocka [Fri, 26 Mar 2021 18:32:32 +0000 (14:32 -0400)]
dm ioctl: fix out of bounds array access when no devices
If there are not any dm devices, we need to zero the "dev" argument in
the first structure dm_name_list. However, this can cause out of
bounds write, because the "needed" variable is zero and len may be
less than eight.
Fix this bug by reporting DM_BUFFER_FULL_FLAG if the result buffer is
too small to hold the "nl->dev" value.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Linus Torvalds [Fri, 26 Mar 2021 18:33:39 +0000 (11:33 -0700)]
Merge tag 'acpi-5.12-rc5' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a memory management regression in ACPICA, repair an ACPI
blacklist entry damaged inadvertently during the 5.11 cycle and fix
the bookkeeping of devices with the same primary device ID in the ACPI
core.
Specifics:
- Make ACPICA use the same object cache consistently when allocating
and freeing objects (Vegard Nossum)
- Add a callback pointer removed inadvertently during the 5.11 cycle
to the ACPI backlight blacklist entry for Sony VPCEH3U1E (Chris
Chiu)
- Make the ACPI device enumeration core use IDA for creating names of
ACPI device objects with the same primary device ID to avoid using
duplicate device object names in some cases (Andy Shevchenko)"
* tag 'acpi-5.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Always create namespace nodes using acpi_ns_create_node()
ACPI: scan: Use unique number for instance_no
ACPI: video: Add missing callback back for Sony VPCEH3U1E
Linus Torvalds [Fri, 26 Mar 2021 18:29:36 +0000 (11:29 -0700)]
Merge tag 'pm-5.12-rc5' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an issue related to device links in the runtime PM framework
and debugfs usage in the Energy Model code.
Specifics:
- Modify the runtime PM device suspend to avoid suspending supplier
devices before the consumer device's status changes to
RPM_SUSPENDED (Rafael Wysocki)
- Change the Energy Model code to prevent it from attempting to
create its main debugfs directory too early (Lukasz Luba)"
* tag 'pm-5.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: EM: postpone creating the debugfs dir till fs_initcall
PM: runtime: Defer suspending suppliers
Linus Torvalds [Fri, 26 Mar 2021 18:19:38 +0000 (11:19 -0700)]
Merge tag 'soc-fixes-5.12' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Too many fixes have accumulated in the soc tree, so this is a fairly
large set. As usual, most of the fixes are for devicetree files, but
there are also notable code changes for imx and omap regressions as
well as some maintainer file updates.
imx:
- Fix an Ethernet issue on imx6ul-14x14-evk board that is caused by
independent PHY reset.
- Add missing `dma-coherent` property for LayerScape device trees to
fix a kernel BUG report.
- Use IRQCHIP_DECLARE for AVIC driver to fix a boot issue on i.MX25
with fw_devlink=on.
- Add missing I2C pinctrl entry for imx8mp-phyboard-pollux-rdk board
to fix the broken I2C GPIO recovery support.
- Add `fsl,use-minimum-ecc` property for imx6ull-myir-mys-6ulx-eval
device tree to fix UBI filesystem mount failure.
at91:
- wrong phy address that blocks Ethernet use on boards with sama5d27
SoM1
- restrictive pin possibilities for sam9x60
omap:
- Fix ocp interconnect bus access error reporting for omap_l3_noc by
setting IRQF_NO_THREAD
- Fix changed mmc slot order regression by adding mmc aliases for
am335x
- Fix dra7 reboot regression caused by invalid pcie reset map
- Fix smartreflex init regression caused by dropped legacy data
- Fix ti-sysc driver warning on unbind if reset is not deasserted
- Fix flakey reset deassert for dra7 iva
stm32:
- MAINTAINER file updates
broadcom:
- brcmstb SoC ID build fix
- MAINTAINER file updates"
* tag 'soc-fixes-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: Add Alain Volmat as STM32 I2C/SMBUS maintainer
MAINTAINERS: Remove Vincent Abriou for STM/STI DRM drivers.
MAINTAINERS: Update some st.com email addresses to foss.st.com
ARM: dts: imx6ull: fix ubi filesystem mount failed
ARM: imx6ul-14x14-evk: Do not reset the Ethernet PHYs independently
arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry
arm64: dts: ls1012a: mark crypto engine dma coherent
arm64: dts: ls1043a: mark crypto engine dma coherent
arm64: dts: ls1046a: mark crypto engine dma coherent
ARM: imx: avic: Convert to using IRQCHIP_DECLARE
ARM: dts: at91: sam9x60: fix mux-mask to match product's datasheet
ARM: dts: at91: sam9x60: fix mux-mask for PA7 so it can be set to A, B and C
ARM: dts: at91-sama5d27_som1: fix phy address to 7
soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva
bus: ti-sysc: Fix warning on unbind if reset is not deasserted
ARM: OMAP2+: Fix smartreflex init regression after dropping legacy data
soc: ti: omap-prm: Fix reboot issue with invalid pcie reset map for dra7
MAINTAINERS: rectify BROADCOM PMB (POWER MANAGEMENT BUS) DRIVER
ARM: dts: am33xx: add aliases for mmc interfaces
bus: omap_l3_noc: mark l3 irqs as IRQF_NO_THREAD
Linus Torvalds [Fri, 26 Mar 2021 18:15:25 +0000 (11:15 -0700)]
Merge tag 'for-linus-5.12b-rc5-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains a small series with a more elegant fix of a problem
which was originally fixed in rc2"
* tag 'for-linus-5.12b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Revert "xen: fix p2m size in dom0 for disabled memory hotplug case"
xen/x86: make XEN_BALLOON_MEMORY_HOTPLUG_LIMIT depend on MEMORY_HOTPLUG
Linus Torvalds [Fri, 26 Mar 2021 18:05:18 +0000 (11:05 -0700)]
Merge tag 'drm-fixes-2021-03-26' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"As expected last week things were overly quiet so this week things
seem to have caught up. It still isn't too major.
msm and amdgpu lead the size here, the msm fixes are pretty varied
across the driver, the amdgpu one is mostly the S0ix fixes with some
other minor ones. Otherwise there are a few i915 fixes and one each
for nouveau, etnaviv and rcar-du.
msm:
- pll fixes
- shutdown hook fix
- runtime resume fix
- clear_oob fix
- kms locking fix
- display aux retry fix
rcar-du:
- warn_on in encoder init fix
etnaviv:
- Use FOLL_FORCE and FOLL_LONGTERM
i915:
- DisplayPort LTTPR fixes around link training and limiting it
according to supported spec version.
- Fix enabled_planes bitmask to really represent only logically
enabled planes.
- Fix DSS CTL registers for ICL DSI transcoders
- Fix the GT fence revocation runtime PM logic.
nouveau:
- cursor size regression fix
amdgpu:
- S0ix fixes
- Add PCI ID
- Polaris PCIe DPM fix
- Display fix for high refresh rate monitors"
* tag 'drm-fixes-2021-03-26' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/nouveau/kms/nve4-nv108: Limit cursors to 128x128
drm/i915: Fix the GT fence revocation runtime PM logic
drm/amdgpu/display: restore AUX_DPHY_TX_CONTROL for DCN2.x
drm/amdgpu: Add additional Sienna Cichlid PCI ID
drm/amd/pm: workaround for audio noise issue
drm/i915/dsc: fix DSS CTL register usage for ICL DSI transcoders
drm/i915: Fix enabled_planes bitmask
drm/i915: Disable LTTPR support when the LTTPR rev < 1.4
drm/i915: Disable LTTPR support when the DPCD rev < 1.4
drm/i915/ilk-glk: Fix link training on links with LTTPRs
drm/msm/disp/dpu1: icc path needs to be set before dpu runtime resume
drm/amdgpu: skip kfd suspend/resume for S0ix
drm/amdgpu: drop S0ix checks around CG/PG in suspend
drm/amdgpu: skip CG/PG for gfx during S0ix
drm/amdgpu: update comments about s0ix suspend/resume
drm/amdgpu/swsmu: skip gfx cgpg on s0ix suspend
drm/amdgpu: re-enable suspend phase 2 for S0ix
drm/amdgpu: move s0ix check into amdgpu_device_ip_suspend_phase2 (v3)
drm/amdgpu: clean up non-DC suspend/resume handling
drm/amdgpu: don't evict vram on APUs for suspend to ram (v4)
...
Pavel Machek [Fri, 26 Mar 2021 09:01:52 +0000 (10:01 +0100)]
remove Dan Murphy from TI from MAINTAINERS
Dan's address bounces, and has been bouncing for some time as he moved
to other projects.
I believe TI should be more careful with this, and should assign
alternate contacts for their drivers.
Anyway what we can do now is to remove the obsolete address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafael J. Wysocki [Fri, 26 Mar 2021 15:55:56 +0000 (16:55 +0100)]
Merge branches 'acpi-video' and 'acpi-scan'
* acpi-video:
ACPI: video: Add missing callback back for Sony VPCEH3U1E
* acpi-scan:
ACPI: scan: Use unique number for instance_no
Rafael J. Wysocki [Fri, 26 Mar 2021 15:44:26 +0000 (16:44 +0100)]
Merge branch 'pm-em'
* pm-em:
PM: EM: postpone creating the debugfs dir till fs_initcall
Shyam Prasad N [Thu, 25 Mar 2021 12:34:54 +0000 (12:34 +0000)]
cifs: Adjust key sizes and key generation routines for AES256 encryption
For AES256 encryption (GCM and CCM), we need to adjust the size of a few
fields to 32 bytes instead of 16 to accommodate the larger keys.
Also, the L value supplied to the key generator needs to be changed from
to 256 when these algorithms are used.
Keeping the ioctl struct for dumping keys of the same size for now.
Will send out a different patch for that one.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Steve French <stfrench@microsoft.com>
Leo Yan [Sat, 20 Mar 2021 10:45:54 +0000 (18:45 +0800)]
perf test: Change to use bash for daemon test
When executing the daemon test on Arm64 and x86 with Debian (Buster)
distro, both skip the test case with the log:
# ./perf test -v 76
76: daemon operations :
--- start ---
test child forked, pid 11687
test daemon list
trap: SIGINT: bad trap
./tests/shell/daemon.sh: 173: local: cpu-clock: bad variable name
test child finished with -2
---- end ----
daemon operations: Skip
So the error happens for the variable expansion when use local variable
in the shell script. Since Debian Buster uses dash but not bash as
non-interactive shell, when execute the daemon testing, it hits a known
issue for dash which was reported [1].
To resolve this issue, one option is to add double quotes for all local
variables assignment, so need to change the code from:
local line=`perf daemon --config ${config} -x: | head -2 | tail -1`
... to:
local line="`perf daemon --config ${config} -x: | head -2 | tail -1`"
But the testing script has bunch of local variables, this leads to big
changes for whole script.
On the other hand, the testing script asks to use the "local" feature
which is bash-specific, so this patch explicitly uses "#!/bin/bash" to
ensure running the script with bash.
After:
# ./perf test -v 76
76: daemon operations :
--- start ---
test child forked, pid 11329
test daemon list
test daemon reconfig
test daemon stop
test daemon signal
signal 12 sent to session 'test [11596]'
signal 12 sent to session 'test [11596]'
test daemon ping
test daemon lock
test child finished with 0
---- end ----
daemon operations: Ok
[1] https://bugs.launchpad.net/ubuntu/+source/dash/+bug/139097
Fixes:
2291bb915b55 ("perf tests: Add daemon 'list' command test")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210320104554.529213-1-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Dave Airlie [Fri, 26 Mar 2021 02:59:21 +0000 (12:59 +1000)]
Merge tag 'drm-msm-fixes-2021-02-25' of https://gitlab.freedesktop.org/drm/msm into drm-fixes
- pll fixes
- shutdown hook fix
- runtime resume fix
- clear_oob fix
- kms locking fix
- display aux retry fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvmiMKRms_NVavD=NA_jbuexZUcqqL35ke7umqpp-TxMw@mail.gmail.com
Linus Torvalds [Thu, 25 Mar 2021 23:46:43 +0000 (16:46 -0700)]
Merge tag 'integrity-v5.12-fix' of git://git./linux/kernel/git/zohar/linux-integrity
Pull integrity fix from Mimi Zohar:
"Just one patch to address a NULL ptr dereferencing when there is a
mismatch between the user enabled LSMs and IMA/EVM"
* tag 'integrity-v5.12-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
integrity: double check iint_cache was initialized
Linus Torvalds [Thu, 25 Mar 2021 22:38:22 +0000 (15:38 -0700)]
Merge tag 'for-5.12-rc4-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Fixes for issues that have some user visibility and are simple enough
for this time of development cycle:
- a few fixes for rescue= mount option, adding more checks for
missing trees
- fix sleeping in atomic context on qgroup deletion
- fix subvolume deletion on mount
- fix build with M= syntax
- fix checksum mismatch error message for direct io"
* tag 'for-5.12-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix check_data_csum() error message for direct I/O
btrfs: fix sleep while in non-sleep context during qgroup removal
btrfs: fix subvolume/snapshot deletion not triggered on mount
btrfs: fix build when using M=fs/btrfs
btrfs: do not initialize dev replace for bad dev root
btrfs: initialize device::fs_info always
btrfs: do not initialize dev stats if we have no dev_root
btrfs: zoned: remove outdated WARN_ON in direct IO
Dave Airlie [Thu, 25 Mar 2021 20:28:17 +0000 (06:28 +1000)]
Merge tag 'amd-drm-fixes-5.12-2021-03-24' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.12-2021-03-24:
amdgpu:
- S0ix fixes
- Add PCI ID
- Polaris PCIe DPM fix
- Display fix for high refresh rate monitors
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210324210630.3949-1-alexander.deucher@amd.com
Dave Airlie [Thu, 25 Mar 2021 20:25:08 +0000 (06:25 +1000)]
Merge branch 'linux-5.12' of git://github.com/skeggsb/linux into drm-fixes
- cursor size fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv7js90N_PYc8JncQA9Hu0yjbg+vPw109FKxJ538nZ=fag@mail.gmail.com
Dave Airlie [Thu, 25 Mar 2021 20:21:18 +0000 (06:21 +1000)]
Merge tag 'drm-intel-fixes-2021-03-25-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- DisplayPort LTTPR fixes around link training and limiting it
according to supported spec version. (Imre)
- Fix enabled_planes bitmask to really represent only logically
enabled planes (Ville).
- Fix DSS CTL registers for ICL DSI transcoders (Jani)
- Fix the GT fence revocation runtime PM logic. (Imre)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YFxYdrjqeUtSu+3p@intel.com