Xu Ziyuan [Wed, 3 Aug 2016 03:55:06 +0000 (11:55 +0800)]
rockchip: add usb mass storage feature support for rk3288
Enable ums feature for rk3288 boards, so that we can mount the mmc
device to PC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Wed, 3 Aug 2016 03:55:05 +0000 (11:55 +0800)]
rockchip: add basic partitions support for rk3288
For compatibility with distro boot, fastboot, and mount the mmc deivce
to PC via usb mass storage feature, GPT partitions are essential.
You should write the partitions to mmc device prior to use above
feature.
=> gpt write mmc 1 $partitions
GPT successfully written to block device!
success!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Mon, 1 Aug 2016 00:46:19 +0000 (08:46 +0800)]
rockchip: add support for rk3288 miniarm board
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Heiko Stübner [Fri, 29 Jul 2016 12:47:21 +0000 (14:47 +0200)]
move: rockchip: move clock drivers into a subdirectory
With the number of Rockchip clock drivers increasing, don't clutter up
the core drivers/clk directory with them and instead move them out of
the way into a separate subdirectory.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Updated for rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 29 Jul 2016 02:35:25 +0000 (10:35 +0800)]
rk3399: add basic soc driver
This patch add driver for:
- clock driver including set_rate for cpu, mmc, vop, I2C.
- sysreset driver
- grf syscon driver
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sandy Patterson [Thu, 28 Jul 2016 13:49:01 +0000 (09:49 -0400)]
rockchip: rockchip, sdram-channel 0xff fix remaining dts
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Thu, 28 Jul 2016 03:42:34 +0000 (11:42 +0800)]
rockchip: add fastboot support for rk3036 board
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Scott Wood [Tue, 19 Jul 2016 22:51:55 +0000 (17:51 -0500)]
powerpc/86xx: Increase boot map size to 256 MiB
This is what Linux maps on classic PPC during boot, and modern kernel
images don't fit within the current 8 MiB uncompressed limit.
Adjust image load addresses to be above this limit to avoid conflicts.
Signed-off-by: Scott Wood <oss@buserror.net>
Reviewed-by: York Sun <york.sun@nxp.com>
Tom Rini [Wed, 3 Aug 2016 00:45:24 +0000 (20:45 -0400)]
Merge git://git.denx.de/u-boot-fsl-qoriq
Hou Zhiqiang [Fri, 29 Jul 2016 11:26:34 +0000 (19:26 +0800)]
ARMv8/fsl-ppa: Consolidate PPA image stored-media flag for XIP
The PPA binary may be stored on QSPI flash instead of NOR.
So, deprecated CONFIG_SYS_LS_PPA_FW_IN_NOR in favour of
CONFIG_SYS_LS_PPA_FW_IN_XIP to prevent fragmentation of code
by addition of a new QSPI specific flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 29 Jul 2016 10:26:37 +0000 (18:26 +0800)]
arm/PSCI: Add support for creating ARMv7 PSCI version 1.0 DT node
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 29 Jul 2016 10:26:36 +0000 (18:26 +0800)]
arm/PSCI: Fixed the backward compatiblity issue
Appended the compatible strings of old version PSCI to the latest
version supported. And there are some psci functions' property must
be added to DT only for psci version 0.1, including cpu_on, cpu_off,
cpu_suspend, migrate.
Note, ARMv8 Secure Firmware Framework doesn't support PSCI ver 0.1.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Fri, 29 Jul 2016 10:26:35 +0000 (18:26 +0800)]
arm/PSCI: Removed unused code
Identify the PSCI node only by its name, so removed the code finding
it by compatible string.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Fri, 29 Jul 2016 16:02:29 +0000 (09:02 -0700)]
driver/ddr/fsl: Fix timing_cfg_2
Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the
change was wrong. wr_lat has 5 bits with MSB at [13] and lower
4 bits at [9:12], in big-endian convention.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
York Sun [Fri, 29 Jul 2016 15:46:49 +0000 (08:46 -0700)]
board/freescale: Update MAINTAINERS files
Update maintainers for secure boot targets.
Signed-off-by: York Sun <york.sun@nxp.com>
Wenbin Song [Fri, 15 Jul 2016 09:17:46 +0000 (17:17 +0800)]
armv8: ls1043a: enable pxe commands
Enable pxe command for ls1043ardb and ls1043aqds.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Prabhakar Kushwaha [Tue, 19 Jul 2016 10:24:33 +0000 (15:54 +0530)]
armv8: ls1012a: Update Refresh cycle for DDR
Refresh cycle value must be selected based on the frequency
of DDR. tREFI = 7.8 us as per JEDEC. The value for MDREF[REF_CNT]
should be based on round up (tREFI/tCK) formula. For 500MHz, mdref
value should be 0x0f3c8000.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Prabhakar Kushwaha [Tue, 19 Jul 2016 10:24:22 +0000 (15:54 +0530)]
armv8: ls1012a: Enable DDR row-bank-column decoding
Enable DDR row-bank-column decoding to decode DDR address as
row-bank-column instead of bank-row-column for improving
performance of serial data transfers.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Prabhakar Kushwaha [Tue, 19 Jul 2016 08:35:47 +0000 (14:05 +0530)]
board: ls1012aqds: Update LBMAP_MASK and RST_CTL_RESET
qixis_reset altbank usagge ~QIXIS_LBMAP_MASK in code. So define
inverse value QIXIS_LBMAP_MASK.
Also, update QIXIS_RST_CTL_RESET value to keep RST_CTL[REQ_MOD]
as 0b11 i.e. PORESET during qixis_reset
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Thu, 14 Jul 2016 17:27:50 +0000 (13:27 -0400)]
crypto/fsl: Update blob cmd to accept 64bit addresses
Update blob cmd to accept 64bit source, key modifier and destination
addresses. Also correct output result print format for fsl specific
implementation of blob cmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yunhui Cui [Wed, 13 Jul 2016 02:46:27 +0000 (10:46 +0800)]
driver: spi: fsl-qspi: remove compile Warnings
Warnins log:
drivers/spi/fsl_qspi.c: In function ‘qspi_ahb_read’:
drivers/spi/fsl_qspi.c:400:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy(rxbuf, (u8 *)(priv->cur_amba_base + priv->sf_addr), len);
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Mon, 1 Aug 2016 16:00:13 +0000 (09:00 -0700)]
powerpc/mpc85xx: Update erratum workaround for A006379
Update erratum workaround for A006379 to set register CPCHDBCR0
with value 0x001e0000, replacing the old value 0x003c0000.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Dave Liu <dave.liu@nxp.com>
Tom Rini [Tue, 2 Aug 2016 11:32:30 +0000 (07:32 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-microblaze
Jaehoon Chung [Mon, 1 Aug 2016 03:35:20 +0000 (12:35 +0900)]
MAINTAINERS, git-mailrc: Update the mmc maintainer
Update the mmc maintainer from Pantelis to me.
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Michal Simek [Mon, 1 Aug 2016 06:49:12 +0000 (08:49 +0200)]
ARM64: zynqmp: Do not enable DM_MMC by default
The patch:
"dm: mmc: zynq: Convert zynq to use driver model for MMC"
(sha1:
329a449f2c289b4de8f892fca1d9379ce5fd81b8)
added dependency on enabling some MMC options by default.
There are minimal ZynqMP configurations which require
only minimal configurations to be enabled to keep u-boot size
as lower as possible.
Move options to defconfig instead.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Soren Brinkmann [Wed, 27 Jul 2016 21:12:03 +0000 (14:12 -0700)]
ARM64: zynqmp: Fix stack pointer initialization
This partly reverts commit:
"ARM64: zynqmp: Add SPL support support"
(sha1:
e6a9ed04e78cf87ec97e306fa4e7a1669ef98df6)
Stack can rewrite ATF code.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 27 Jul 2016 12:56:49 +0000 (14:56 +0200)]
ARM64: zynqmp: Define config USB_STORAGE through defconfig
Define config USB_STORAGE through defconfig for all
Xilinx ZynqMP boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 27 Jul 2016 13:08:03 +0000 (15:08 +0200)]
xilinx: Sync defconfigs with the latest Kconfig layout
Update Microblaze, Zynq and ZynqMP defconfigs to reflect
latest Kconfig changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 27 Jul 2016 11:40:19 +0000 (13:40 +0200)]
ARM64: zynqmp: Wire up PSCI reset
Using PSCI to reset the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 29 Jul 2016 11:03:29 +0000 (13:03 +0200)]
ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes
Serial driver is getting clk information via DT that's why
also clk node needs to have this flag.
Different behavior was introduced by:
"dm: Use dm_scan_fdt_dev() directly where possible"
(sha1:
911954859d6dece49c3e4835faea004cfe392506)
where simple-bus driver starts to call dm_scan_fdt_dev() which has
additional logic around pre_reloc_only parameter which exclude
clk nodes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Jul 2016 02:33:08 +0000 (20:33 -0600)]
Drop references to MAKEALL in the documentation
It is confusing to mention MAKEALL when it is not the normal way of building
U-Boot anymore. Update the documentation to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:33:07 +0000 (20:33 -0600)]
Drop the MAKEALL tool
Buildman has been around for 3 years now. It has had a lot of use and
testing. Perhaps it is time to remove MAKEALL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:33:06 +0000 (20:33 -0600)]
buildman: Add a quick-start note
For those who just want to build a board, it is useful to see a quick hint
right at the start of the documentation. Add a few commands showing how to
download toolchains and build a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Jul 2016 02:33:05 +0000 (20:33 -0600)]
buildman: Avoid overwriting existing toolchain entries
The current code for setting up the toolchain config always writes the new
paths to an item called 'toolchain'. This means that it will overwrite any
existing toolchain item with the same name. In practice, this means that:
buildman --fetch-arch all
will fetch all toolchains, but only the path of the final one will be added
to the config. This normally works out OK, since most toolchains are the
same version (e.g. gcc 4.9) and will be found on the same path. But it is
not correct and toolchains for archs which don't use the same version will
not function as expected.
Adjust the code to use a complete glob of the toolchain path.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:33:04 +0000 (20:33 -0600)]
buildman: Drop the toolchain error when downloading toolchains
It doesn't make sense to complain about missing toolchains when the
--fetch-arch option is being used. The user is presumably aware that there
is a toolchain problem and is actively correcting it by running with this
option.
Refactor the code to avoid printing this confusing message.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Jul 2016 02:33:03 +0000 (20:33 -0600)]
buildman: Fix a typo in TestSettingsHasPath()
The function comment should say 'buildman'. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:33:02 +0000 (20:33 -0600)]
buildman: Improve the toolchain progress/error output
Use colour to make it easier to see what is going on. Also print a message
before downloading a new toolchain. Mention --fetch-arch in the message that
is shown when there are no available toolchains, since this is the quickest
way to resolve the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:33:01 +0000 (20:33 -0600)]
buildman: Allow the toolchain error to be suppressed
When there are no toolchains a warning is printed. But in some cases this is
confusing, such as when the user is fetching new toolchains.
Adjust the function to supress the warning in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Jul 2016 02:33:00 +0000 (20:33 -0600)]
buildman: Fix the 'help' test to use the correct path
When buildman is run via a symlink, this test fails. Fix it to work the same
way as buildman itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Jul 2016 02:32:59 +0000 (20:32 -0600)]
buildman: Automatically create a config file if needed
If there is no ~/.buildman file, buildman currently complains and exists. To
make things a little more friendly, create an empty one automatically. This
will not allow things to be built, but --fetch-arch can be used to handle
that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 28 Jul 2016 02:32:58 +0000 (20:32 -0600)]
buildman: Tidy up the README a little
Tidy up some problems found by a recent review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Michal Simek [Thu, 28 Jul 2016 07:06:41 +0000 (09:06 +0200)]
libfdt: Introduce new ARCH_FIXUP_FDT option
Add new Kconfig option to disable arch_fixup_fdt() calls for cases where
U-Boot shouldn't update memory setup in DTB file.
One example of usage of this option is to boot OS with different memory
setup than U-Boot use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 1 Aug 2016 00:31:13 +0000 (20:31 -0400)]
Merge git://git.denx.de/u-boot-rockchip
Hans de Goede [Wed, 27 Jul 2016 16:06:35 +0000 (18:06 +0200)]
sunxi: Re-enable h3 emac support
With the recent bug fixes for the sun8i_emac driver all known issues
are resolved, so we can re-enable the driver.
While at it, also enable the emac on the Orange Pi One.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Jagan Teki <jteki@openedev.com>
Hans de Goede [Wed, 27 Jul 2016 15:31:17 +0000 (17:31 +0200)]
net: sun8i_emac: Fix DMA alignment issues with the rx / tx buffers
This fixes the following CACHE warnings when using sun8i_emac:
=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
CACHE: Misaligned operation at range [
7bf594a8,
7bf59628]
BOOTP broadcast 3
CACHE: Misaligned operation at range [
7bf59c90,
7bf59e10]
CACHE: Misaligned operation at range [
7bf5a478,
7bf5a5f8]
DHCP client bound to address 10.42.43.80 (1009 ms)
Note this commit also changes the max rx size from 2024 to 2044,
matching what the kernel driver uses.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Fri, 29 Jul 2016 09:47:03 +0000 (11:47 +0200)]
sunxi: On newer SoCs use words 1-3 instead of just word 3 from the SID
It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID
are always 0 on H3 making it a poor candidate to use as source for the
serialnr / mac-address, and the other non constant words (1 and 2) also
have quite a few bits which are the same for some boards,
This commits switches to using the crc32 of words 1 - 3 to get a
more unique value for the mac-address / serialnr.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 27 Jul 2016 15:58:06 +0000 (17:58 +0200)]
sunxi: Ensure that the NIC specific bytes of the mac are not all 0
On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to
the NIC specific bytes of the mac all being 0, which leads to the
boards not getting an ipv6 address from the dhcp server.
This commits adds a check to ensure this does not happen.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Chen-Yu Tsai [Fri, 22 Jul 2016 08:13:00 +0000 (16:13 +0800)]
sunxi: Hummingbird_A31_defconfig: Drop MACPWR option
MACPWR was used to bring the Ethernet PHY out of reset. The designware
driver now supports the phy reset gpio binding, so this is no longer
needed. In fact in requesting the same GPIO, it makes the designware
driver fail to probe.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Fri, 22 Jul 2016 08:12:59 +0000 (16:12 +0800)]
sunxi: gpio: Add .xlate function for gpio phandle resolution
sunxi uses a 2 cell phandle for gpio bindings. Also there are no
seperate nodes for each pin bank.
Add a custom .xlate function to map gpio phandles to the correct
pin bank device. This fixes gpio_request_by_name usage.
Fixes:
7aa974858422 ("dm: sunxi: Modify the GPIO driver to support driver
model")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:30 +0000 (18:28 +0800)]
rockchip: add support for rk3288 PopMetal board
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:29 +0000 (18:28 +0800)]
rockchip: add basic support for fennec-rk3288 board
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:27 +0000 (18:28 +0800)]
rockchip: rk3288: move evb board to rockchip folder
The 'evb-rk3288' is not a vendor name, change it to 'rockchip' which is
the real vendor name.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:26 +0000 (18:28 +0800)]
rockchip: rk3288: revise CONFIG_FASTBOOT_BUF_ADDR
CONFIG_SYS_LOAD_ADDR is absolutely safe to store image for
fastboot.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:25 +0000 (18:28 +0800)]
rockchip: remove the duplicated macro config
CONFIG_DOS_PARTITION and CONFIG_EFI_PARTITION are already included in
config_distro_defaults.h, and we don't need them in SPL stage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:24 +0000 (18:28 +0800)]
rockchip: rk3288: disable fastboot in SPL stage
Reduce compilation time for SPL.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:23 +0000 (18:28 +0800)]
Revert "rockchip: Move the MMC setup check earlier"
Boot Rom wouldn't initialize sdmmc while booting from eMMC. We need to
setup sdmmc gpio, otherwise we will hit an error below:
=>mmc info
blk_get_device: if_type=6, devnum=0: dwmmc@
ff0c0000.blk, 6, 0
uclass_find_device_by_seq: 0 -1
uclass_find_device_by_seq: 0 0
- -1 -1
- -1 0
- found
uclass_find_device_by_seq: 0 1
- -1 -1
- -1 0
- not found
fdtdec_get_int_array: interrupts
get_prop_check_min_len: interrupts
Buswidth = 1, clock: 0
Buswidth = 1, clock: 400000
Sending CMD0
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
This reverts commit
6efeeea79c880d3dd262e0dca9da2687f0ab68c9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:22 +0000 (18:28 +0800)]
cosmetic: rockchip: rk3288: pinctrl: fix config symbol naming
Revise config to CONFIG_ROCKCHIP_RK3288_PINCTRL.
Signed-off-by: Ziyuan Xu <jk.kernel@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
jk.kernel@gmail.com [Tue, 26 Jul 2016 10:28:21 +0000 (18:28 +0800)]
rockchip: add a dummy byte for the sdram-channel property
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Ziyuan Xu <jk.kernel@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
John Keeping [Mon, 25 Jul 2016 09:02:05 +0000 (10:02 +0100)]
rockchip: rk3288: Fix pinctrl for GPIO bank 0
Bank 0 is the "PMU GPIO" bank which is controlled by the PMU registers
rather than the GRF registers. In the GRF the top half of the register
is used as a mask so that some bits can be updated without affecting the
others, but in the PMU this feature is not provided and the top half of
the register is reserved.
Take the same approach as the Linux driver to update the value via
read-modify-write but setting the mask for only the bits that have
changed. The PMU registers ignore the top 16 bits so this works for
both GRF and PMU iomux registers.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 25 Jul 2016 03:45:54 +0000 (11:45 +0800)]
rk3399: Reserve space for ARM Trust Firmware
RK3399 needs reserve 0x200000 at the beginning of DRAM, for ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Sat, 23 Jul 2016 07:09:28 +0000 (15:09 +0800)]
rockchip: rk3036: update MAINTAINER file
Update MAINTAINER files for kylin_rk3036, evb_rk3036.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 22 Jul 2016 09:41:37 +0000 (17:41 +0800)]
configs: rockchip: remove no use MACRO
The CONFIG_ROCKCHIP_COMMON and CONFIG_SPL_ROCKCHIP_COMMON are no use now,
remove them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 22 Jul 2016 09:22:50 +0000 (17:22 +0800)]
mmc-uclass: correct the device number
Not like the mmc-legacy which the devnum starts from 1, it starts from 0
in mmc-uclass, so the device number should be (devnum + 1) in get_mmc_num().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Angelo Dureghello [Sat, 21 May 2016 22:14:29 +0000 (00:14 +0200)]
m68k: code reformatting for all start.S files
This patch is style-related only, to reformat all the start.S code,
actually not following a coherent style inside single files and
between different cpu start.S files.
Linux format has been respected, as
- max line width at 80 columns
- one 8 cols tab between asm instructions and operands
- inline comments, where any, fixed at col 41
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Vignesh R [Fri, 29 Jul 2016 08:52:30 +0000 (14:22 +0530)]
ARM: am57xx_evm: Enable QSPI support
AM571x IDK and AM572x IDK EVMs have spansion s25fl256s QSPI flash on the
board connected to TI QSPI IP over CS0. Therefore enable QSPI support.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Fri, 29 Jul 2016 08:52:31 +0000 (14:22 +0530)]
ARM: dts: am57xx-idk-common: Enable support for QSPI
AM571x and AM572x IDK have a spansion s25fl256s QSPI flash on the board
connected to TI QSPI over CS0. Hence, add QSPI and flash slave
DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Thu, 28 Jul 2016 11:57:57 +0000 (17:27 +0530)]
configs: am43xx_evm_defconfig: Enable CONFIG_SPI_FLASH_BAR
AM437x SK and AM437x IDK EVMs have 64MB flash, therefore enable
CONFIG_SPI_FLASH_BAR to access flash regions above 16MB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Mon, 25 Jul 2016 10:15:47 +0000 (15:45 +0530)]
ARM: dts: dra7xx: Update spi-max-frequency for QSPI
According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Mon, 25 Jul 2016 10:15:46 +0000 (15:45 +0530)]
configs: dra7xx: Update QSPI speed to 76.8MHz
Now that QSPI driver can support 76.8MHz, update the
CONFIG_SF_DEFAULT_SPEED to the same value.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Mon, 25 Jul 2016 10:15:45 +0000 (15:45 +0530)]
spi: ti_qspi: dra7xx: Add support to use 76.8MHz clock
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Lokesh Vutla [Mon, 25 Jul 2016 10:15:44 +0000 (15:45 +0530)]
ARM: dra7xx: Change DPLL_PER_HS13 divider value
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Wenyou Yang [Tue, 5 Jul 2016 05:17:12 +0000 (13:17 +0800)]
sf: sf_params: Add AT25DF321 flash support
Add AT25DF321 flash support.
Fix AT25DF321A device name.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Vignesh R [Fri, 22 Jul 2016 05:25:50 +0000 (10:55 +0530)]
spi: ti_qspi: Remove delay in read path for dra7xx
As per commit
b545a98f5dc563 ("spi: ti_qspi: Add delay
for successful bulk erase) says its added to meet bulk erase timing
constraints. But bulk erase is a cmd to flash and delay in read path
does not make sense. Morever, testing on DRA74/DRA72 evm has shown that
this delay is no longer required.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Fri, 22 Jul 2016 05:25:49 +0000 (10:55 +0530)]
spi: ti_qspi: Fix compiler warning when DEBUG macro is set
clk_div is uninitialized at the beginning of ti_spi_set_speed(), move
debug() print after clk_div calculation to avoid compiler warning and to
have proper value of clk_div printed during debugging.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Fri, 22 Jul 2016 05:25:48 +0000 (10:55 +0530)]
spi: ti_qspi: Fix failure on multiple READ_ID cmd
Populating QSPI_RD_SNGL bit(0x1) in priv->cmd means that value
QSPI_INVAL (0x4) is not written to CMD field of QSPI_SPI_CMD_REG in
ti_qspi_cs_deactivate(). Therefore CS is never deactivated between
successive READ ID which results in sf probe to fail.
Fix this by not populating priv->cmd with QSPI_RD_SNGL and OR it wih
priv->cmd as required (similar to the convention followed in the
driver).
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Moritz Fischer [Thu, 14 Jul 2016 23:22:39 +0000 (16:22 -0700)]
spi: Add support for N25Q016A
This commit adds support in the spi-nor driver for the
N25Q016A, a 16Mbit SPI NOR flash from Micron.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tom Rini [Thu, 28 Jul 2016 12:45:00 +0000 (08:45 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Fabio Estevam [Wed, 27 Jul 2016 00:27:49 +0000 (21:27 -0300)]
MAINTAINERS: i.MX: Add board/freescale/*mx* path
Pass the board/freescale/*mx*/ path as files maintained by Stefano
Babic.
While this is not ideal and does not cover all the i.MX board cases,
it gives at least a better hint for the /scripts/get_maintainer.pl
tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Wed, 27 Jul 2016 00:08:58 +0000 (21:08 -0300)]
mx7dsabresd: MAINTAINERS: Add mx7dsabresd_secure_defconfig
Add an entry for the mx7dsabresd_secure_defconfig target.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Stefan Agner [Tue, 26 Jul 2016 05:57:47 +0000 (22:57 -0700)]
mx7_common: initialize generic timer on all CPU's
Use CONFIG_TIMER_CLK_FREQ to let the non-secure init code initialize
the generic timer on all CPU's. This allows to make use of the timer
freuquency register also on other CPU than the start CPU which is
important for KVM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Diego Dorta [Mon, 25 Jul 2016 16:45:30 +0000 (13:45 -0300)]
mx6ul_14x14_evk: Remove unused define
Remove unused define constant.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Sat, 23 Jul 2016 16:23:42 +0000 (13:23 -0300)]
cgtqmx6eval: Remove uneeded PHYS_SDRAM_SIZE
cgtqmx6eval uses the imx_ddr_size() function to calculate the DDR size in
runtime, so there is no need to define PHYS_SDRAM_SIZE.
Remove the unneeded definition.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Estevam [Sat, 23 Jul 2016 16:23:41 +0000 (13:23 -0300)]
novena: Remove uneeded PHYS_SDRAM_SIZE
novena uses the imx_ddr_size() function to calculate the DDR size in
runtime, so there is no need to define PHYS_SDRAM_SIZE.
Remove the unneeded definition.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
Fabio Estevam [Sat, 23 Jul 2016 16:23:40 +0000 (13:23 -0300)]
bx50v3: Use imx_ddr_size() for calculating the DDR size
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Cc: Martin Donnelly <martin.donnelly@ge.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Sat, 23 Jul 2016 16:23:39 +0000 (13:23 -0300)]
aristainetos: Use imx_ddr_size() for calculating the DDR size
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Fabio Estevam [Sat, 23 Jul 2016 16:23:38 +0000 (13:23 -0300)]
warp: Use imx_ddr_size() for calculating the DDR size
imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Breno Lima [Fri, 22 Jul 2016 18:29:30 +0000 (15:29 -0300)]
warp7: Move some USB configuration options to defconfig
Currently it's recommended to move some configuration options to the
defconfig file.
Move some USB related options to the defconfig file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Stefan Agner [Thu, 21 Jul 2016 04:27:49 +0000 (21:27 -0700)]
colibri_imx7: add Colibri iMX7S/iMX7D module support
This commit adds support for the Toradex Computer on Modules
Colibri iMX7S/iMX7D. The two modules/SoC's are very similar hence
can be easily supported by one board. The board code detects RAM
size at runtime which is one of the differences between the two
boards. The board also uses the UART's in DTE mode, hence making
use of the new DTE support via serial DM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Breno Lima [Fri, 22 Jul 2016 12:12:12 +0000 (09:12 -0300)]
cgtqmx6eval: Replace is_mx6q() for macro
It's not necessary to implement the is_mx6q function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Breno Lima [Fri, 22 Jul 2016 12:11:30 +0000 (09:11 -0300)]
mx6cuboxi: Replace is_mx6q() for macro
It's not necessary to implement the is_mx6q function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Breno Lima [Fri, 22 Jul 2016 12:11:02 +0000 (09:11 -0300)]
wandboard: Replace is_cpu_type() for macro
It's not necessary to use the is_cpu_type function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tim Harvey [Fri, 15 Jul 2016 14:16:29 +0000 (07:16 -0700)]
imx: ventana: add dt fixup for watchdog external reset
Added removal of the fsl,ext-reset-output property in the wdog node for board
revisions that pre-date the addition of the external watchdog reset signal.
This property is a recent addition to mainline linux kernel in order to
specify that the IMX watchdog external reset should be used instead of the
internal chip-level reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 15 Jul 2016 14:16:28 +0000 (07:16 -0700)]
imx: ventana: refactor board-specific dt fixups (no functional change)
Re-factor the board-specific dt fixups so that they are easier to follow
and extend in the future:
- use defines for DT paths
- use switch/case per board
- order models numerically
There is no functional change in the code
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 15 Jul 2016 14:14:25 +0000 (07:14 -0700)]
imx: ventana: make hwconfig initialize based on board configuration
The hwconfig env var allows user to control hardware specific configuration
of board specific features but not all Ventana boards have the same features.
We will use the magic default value of "_UNKNOWN_" to signify that the
bootloader should create this based on detected board model.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 15 Jul 2016 14:14:24 +0000 (07:14 -0700)]
imx: ventana: add extra DIO's for GW5520
The GW5520 has 10 DIO's instead of the typical 4 found on the Ventana
product family.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 15 Jul 2016 14:14:23 +0000 (07:14 -0700)]
imx: ventana: make number of digital I/O's dynamic
Replace the static list of board-specific digital I/O's with a dynamic list.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 15 Jul 2016 14:14:22 +0000 (07:14 -0700)]
imx: ventana: make RS232 enable board specific
Not all Ventana boards have an RS232 transceiver, make it board specific.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Wed, 29 Jun 2016 15:58:00 +0000 (08:58 -0700)]
imx: ventana: re-enable late board info display
3b1f681131149b5f62602f582a7e60b0185a2a49 caused a regression that removes
board info dispaly for Gateworks Ventana boards because it made the invalid
assumption that CONFIG_DISPLAY_BOARDINFO_LATE was the same thing as
CONFIG_DISPLAY_BOARDINFO.
Ventana needs to call show_board_info in late init because we need to have
the i2c eeprom based model info. Re-define CONFIG_DISPLAY_BOARDINFO_LATE
to allow that to happen.
Cc: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 17 Jun 2016 13:20:26 +0000 (06:20 -0700)]
imx: ventana: default pci to disabled
The IMX6 PCIe host controller does not have a proper reset and as such there
are several issues that can arise if PCI is enabled in the bootloader follwed
by Linux trying to re-configure LTSSM and/or toggling PERST# to the devices.
For now, the best approach seems to default to disabling PCI by defaulting
pciedisable=1. This can be overridden by the user if they need PCI in the
bootloader, for example:
- GW552x needing ethernet access in bootloader
- GW16082 expansion board needing a device-tree fixup for irq mapping
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Fri, 17 Jun 2016 13:20:25 +0000 (06:20 -0700)]
pci: allow disabling of pci init/enum via env
Signed-off-by: Tim Harvey <tharvey@gateworks.com>