Fabio Estevam [Mon, 23 Apr 2012 06:06:29 +0000 (06:06 +0000)]
m28evk: Allow to booting a dt kernel
Allow to booting a dt kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Mon, 23 Apr 2012 06:06:28 +0000 (06:06 +0000)]
mx28evk: Allow to booting a dt kernel
Allow to booting a dt kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Wed, 11 Apr 2012 10:22:24 +0000 (10:22 +0000)]
mx6qsabrelite: No need to set the direction for GPIO3_23 again
There is a 'gpio_direction_output(87, 0);' call previously, so the GPIO direction is
already established.
Use gpio_set_value() for changing the GPIO output then.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Fabio Estevam [Tue, 20 Mar 2012 11:40:06 +0000 (11:40 +0000)]
pmic: Add support for the Dialog DA9053 PMIC
Add support for the Dialog DA9053 PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Wed, 22 Feb 2012 00:24:41 +0000 (00:24 +0000)]
MX53: mx53loco: Add SATA support
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
Stefano Babic [Wed, 22 Feb 2012 00:24:40 +0000 (00:24 +0000)]
MX53: Add support to ESG ima3 board
The ESG ima3-mx53 board is based on the Freescale
i.MX53 SOC. It boots from NOR (128 MB) and
supports Ethernet (FEC), SATA.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Wed, 22 Feb 2012 00:24:39 +0000 (00:24 +0000)]
SATA: add driver for MX5 / MX6 SOCs
This driver is part of Freescale's LTIB for
MX5 / MX6.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Terry Lv <r65388@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Stefano Babic [Wed, 22 Feb 2012 00:24:38 +0000 (00:24 +0000)]
MX53: add function to set SATA clock to internal
The MX53 SATA interface can use an internal clock (USB PHY1)
instead of an external clock. This is an undocumented feature, but used
on most Freescale's evaluation boards, such as MX53-loco.
As stated by Freescale's support:
Fuses (but not pins) may be used to configure SATA clocks.
Particularly the i.MX53 Fuse_Map contains the next information
about configuring SATA clocks :
SATA_ALT_REF_CLK[1:0] (offset 0x180C)
'00' - 100MHz (External)
'01' - 50MHz (External)
'10' - 120MHz, internal (USB PHY)
'11' - Reserved
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Wed, 22 Feb 2012 00:24:37 +0000 (00:24 +0000)]
SATA: check for return value from sata functions
sata functions are called even if previous functions failed
because return value is not checked.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Wed, 22 Feb 2012 00:24:36 +0000 (00:24 +0000)]
MX5: Add definitions for SATA controller
Add base address and MXC_SATA_CLK to return
the clock used for the SATA controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Stefano Babic [Wed, 22 Feb 2012 00:24:35 +0000 (00:24 +0000)]
NET: fec_mxc.c: Add a way to disable auto negotiation
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Wed, 22 Feb 2012 00:24:33 +0000 (00:24 +0000)]
Define UART4 and UART5 base addresses
Signed-off-by: Stefano Babic <sbabic@denx.de>
Donghwa Lee [Mon, 23 Apr 2012 15:37:05 +0000 (15:37 +0000)]
EXYNOS: Change bits per pixel value proper for u-boot.
vl_bpix of vidinfo_t was changed proper value for u-boot.
It is used to multiple of 2 by using NBITS() macro.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Donghwa Lee [Thu, 5 Apr 2012 19:36:27 +0000 (19:36 +0000)]
EXYNOS: support TRATS board display function
This patch support TRATS board configuration and display function.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Donghwa Lee [Fri, 6 Apr 2012 05:24:01 +0000 (14:24 +0900)]
LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
This patch support S6E8AX0 amoled driver based on EXYNOS MIPI DSI interface.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Donghwa Lee [Thu, 5 Apr 2012 19:36:21 +0000 (19:36 +0000)]
EXYNOS: support EXYNOS MIPI DSI interface driver.
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI
based LCD Panel could be used with it. This patch supports MIPI-DSI driver
based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
board file and LCD panel driver specific function registered to mipi_dsim_ddi
structure at lcd panel init function called system init.
In the MIPI-DSI driver, find lcd panel driver by using registered
lcd panel name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Donghwa Lee [Thu, 5 Apr 2012 19:36:17 +0000 (19:36 +0000)]
EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
This patch support EXYNOS FB and FIMD display drivers.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Donghwa Lee [Thu, 5 Apr 2012 19:36:15 +0000 (19:36 +0000)]
LCD: add data structure for EXYNOS display driver
Add vidinfo data structure for EXYNOS display driver
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Donghwa Lee [Thu, 5 Apr 2012 19:36:12 +0000 (19:36 +0000)]
EXYNOS: add LCD and MIPI DSI clock interface.
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Donghwa Lee [Thu, 5 Apr 2012 19:36:10 +0000 (19:36 +0000)]
EXYNOS: definitions of system resgister and power management registers.
This is definitions of system registers and power mananagement registers for EXYNOS SoC.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Minkyu Kang [Mon, 2 Apr 2012 07:51:33 +0000 (16:51 +0900)]
SMDK5250: fix compiler warning
this patch fixed following warning.
tzpc_init.c: In function 'tzpc_init':
tzpc_init.c:35: warning: assignment from incompatible pointer type
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Chander Kashyap <chander.kashyap@linaro.org>
Łukasz Majewski [Thu, 29 Mar 2012 01:29:18 +0000 (01:29 +0000)]
misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
TRATS target uses MAX8997 PMIC device instead of MAX8998.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Thu, 29 Mar 2012 01:29:17 +0000 (01:29 +0000)]
misc:pmic:max8997 MAX8997 support for PMIC driver
This commit adds support for MAX8997 PMIC driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Jaehoon Chung [Tue, 27 Mar 2012 20:05:25 +0000 (20:05 +0000)]
TRATS: modify the trats's configuration
Trats is supported 1GiB memory size.
(Each bank size is 512MB.)
And INITRD is unnecessary. So removed them.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Mon, 26 Mar 2012 21:53:48 +0000 (21:53 +0000)]
ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
This patch enables LDO4 power line for preparing proper voltages to be
measured by ADC converter.
This measurement is used for determination of target board HW revision.
Test HW:
Universal_C210 (Exynos4210) rev. 0.0
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Wed, 14 Mar 2012 17:34:02 +0000 (17:34 +0000)]
EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc
in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic
usase of tzpc.
Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Nobuhiro Iwamatsu [Tue, 17 Apr 2012 16:41:54 +0000 (16:41 +0000)]
arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Nobuhiro Iwamatsu [Tue, 17 Apr 2012 16:42:22 +0000 (16:42 +0000)]
arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
With almost all the architecture and board BOARD_LATE_INIT does not use.
CONFIG_BOARD_LATE_INIT is used instead.
This changed CONFIG_BOARD_LATE_INIT from BOARD_LATE_INIT.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Nikita Kiryanov [Mon, 2 Apr 2012 02:29:31 +0000 (02:29 +0000)]
cm-t35: add I2C multi-bus support
Enable I2C multi-bus support and config I2C muxes for I2C2 and I2C3.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tom Rini [Fri, 13 Apr 2012 12:20:05 +0000 (12:20 +0000)]
include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
This define does not control anything, remove it.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 13 Apr 2012 12:20:04 +0000 (12:20 +0000)]
include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
This define does not control anything, remove it.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 13 Apr 2012 12:20:03 +0000 (12:20 +0000)]
omap3: Introduce weak misc_init_r
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tom Rini [Fri, 13 Apr 2012 12:20:02 +0000 (12:20 +0000)]
omap730p2: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 13 Apr 2012 12:20:01 +0000 (12:20 +0000)]
omap5912osk: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 13 Apr 2012 12:20:00 +0000 (12:20 +0000)]
omap4+: Remove CONFIG_ARCH_CPU_INIT
OMAP4/5 had an empty arch_cpu_init() so drop that along with
CONFIG_ARCH_CPU_INIT
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 13 Apr 2012 12:19:59 +0000 (12:19 +0000)]
omap4: Remove CONFIG_SYS_MMC_SET_DEV
This is only used on !CONFIG_GENERIC_MMC which is false here.
Signed-off-by: Tom Rini <trini@ti.com>
Grazvydas Ignotas [Thu, 22 Mar 2012 13:49:23 +0000 (13:49 +0000)]
OMAP3: pandora: drop console kernel argument
As ttyS0 is no longer valid for newer OMAP kernels, and pandora serial
cables are not widespread, simply drop console argument. This should
allow booting old and new kernels with default arguments, and those who
need serial can use a boot script on SD card.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Grazvydas Ignotas [Thu, 22 Mar 2012 13:49:22 +0000 (13:49 +0000)]
OMAP3: pandora: revise GPIO configuration
Update pandora's GPIO setup code with these changes:
- convert to gpiolib
- set up dual voltage GPIOs to match supply of 1.8V by clearing VMODE1
- add GPIO_IO_PWRDNZ configuration for DM3730 variation of pandora
(required to enable GPIO 126, 127, and 129 I/O cells in DM3730)
- add wifi reset pulse as recommended by wifi chip's manufacturer
- drop configuration of GPIOs that u-boot doesn't need
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Grazvydas Ignotas [Thu, 22 Mar 2012 13:49:21 +0000 (13:49 +0000)]
OMAP3: pandora: pin mux updates for DM3730 board variant
DM3730 needs some additional pin mux configuration for GPIOs
126-129 to work, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tom Rini [Fri, 16 Mar 2012 06:34:35 +0000 (06:34 +0000)]
Makefile: Add a 'checkthumb' rule
This rule confirms that if we're on ARM and we have enabled THUMB builds
that we have a new enough toolchain to produce a working binary.
Changes in v2:
- Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F)
- Simplfy checkthumb test after doing the above
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tom Rini [Fri, 16 Mar 2012 05:27:47 +0000 (05:27 +0000)]
tools, config.mk: Add gcc-version.sh, cc-version test from Linux
Added from Linux - commit
fde7d9049e55ab85a390be7f415d74c9f62dd0f9
Signed-off-by: Tom Rini <trini@ti.com>
Aneesh V [Thu, 8 Mar 2012 07:20:22 +0000 (07:20 +0000)]
OMAP4: enable Thumb build
Signed-off-by: Aneesh V <aneesh@ti.com>
Aneesh V [Thu, 8 Mar 2012 07:20:21 +0000 (07:20 +0000)]
omap4+: Avoid using __attribute__ ((__packed__))
Avoid using __attribute__ ((__packed__)) unless it's
absolutely necessary. "packed" will remove alignment
requirements for the respective objects and may cause
alignment issues unless alignment is also enforced
using a pragma.
Here, these packed attributes were causing alignment
faults in Thumb build.
Signed-off-by: Aneesh V <aneesh@ti.com>
Aneesh V [Thu, 8 Mar 2012 07:20:20 +0000 (07:20 +0000)]
armv7: Use -march=armv7-a and thereby enable Thumb-2
Enable -march=armv7-a for armv7 platforms if the tool-chain
supports it. This in turn results in Thumb-2 code generated
for these platforms if CONFIG_SYS_THUMB_BUILD is enabled.
Signed-off-by: Aneesh V <aneesh@ti.com>
Aneesh V [Thu, 8 Mar 2012 07:20:19 +0000 (07:20 +0000)]
ARM: enable Thumb build
Enable Thumb build and ARM-Thumb interworking based on the new
config flag CONFIG_SYS_THUMB_BUILD
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Aneesh V [Thu, 8 Mar 2012 07:20:18 +0000 (07:20 +0000)]
armv7: add appropriate headers for assembly functions
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Aneesh V [Thu, 8 Mar 2012 07:20:17 +0000 (07:20 +0000)]
arm: adapt asm/linkage.h from Linux
This will add ARM specific over-rides for the defines
from linux/linkage.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
SRICHARAN R [Mon, 12 Mar 2012 02:25:52 +0000 (02:25 +0000)]
OMAP5: reset: Use cold reset in case of 5430ES1.0
Warm reset is not functional in case of omap5430ES1.0.
So override the weak reset_cpu function to use
cold reset instead.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 19:49:32 +0000 (19:49 +0000)]
OMAP3+: reset: Create a common reset layer.
The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Balaji T K [Mon, 12 Mar 2012 02:25:50 +0000 (02:25 +0000)]
mmc: omap5evm: Add eMMC saveenv support
Save env to eMMC
Signed-off-by: Balaji T K <balajitk@ti.com>
Balaji T K [Mon, 12 Mar 2012 02:25:49 +0000 (02:25 +0000)]
omap5: pbias ldo9 turn on
Add omap5 pbias configuration for mmc1/sd lines
and set voltage for sd data i/o lines
Signed-off-by: Balaji T K <balajitk@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:48 +0000 (02:25 +0000)]
power: twl6035: add palmas PMIC support
palmas/TWL6035 is power IC for omap5 evm boards
Signed-off-by: Balaji T K <balajitk@ti.com>
Balaji T K [Mon, 12 Mar 2012 02:25:47 +0000 (02:25 +0000)]
arm: omap5: correct boot device mode7 for eMMC
In OMAP5 Boot device mode of 6 and 7 should be mapped to mmc2/eMMC
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:46 +0000 (02:25 +0000)]
OMAP4/5: emif: Correct the emif power mgt shadow register bit fields.
PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:45 +0000 (02:25 +0000)]
OMAP5: ddr: Change the ddr device name.
The ddr part name used in OMAP5 ES1.0 soc is a SAMSUNG part and
not a ELPIDA part. So change this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:44 +0000 (02:25 +0000)]
OMAP5: defconfig: Align the defconfig for 5430 ES1.0
Adding the nessecary changes for OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:43 +0000 (02:25 +0000)]
OMAP4/5: device: Add support to get the device type.
Add support to identify the device as GP/EMU/HS.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:42 +0000 (02:25 +0000)]
OMAP4/5: Make the sysctrl structure common
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:41 +0000 (02:25 +0000)]
OMAP5: SRAM: Change the SRAM base address.
The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:40 +0000 (02:25 +0000)]
OMAP4/5: Make the silicon revision variable common.
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:39 +0000 (02:25 +0000)]
OMAP5: hwinit: Add the missing break statement
The break statement is missing in init_omap_revision function, resulting
in a wrong revision identification. So fixing this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:38 +0000 (02:25 +0000)]
OMAP5: palmas: Configure nominal opp vdd values
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.
Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
http://lists.denx.de/pipermail/u-boot/2012-March/119151.html
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:37 +0000 (02:25 +0000)]
OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon.
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:36 +0000 (02:25 +0000)]
OMAP5: io: Configure the io settings for omap5430 sevm board.
The control module provides options to set various signal
integrity parameters like the output impedance, slew rate,
load capacitance for different pad groups. Configure these
as required for the omap5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:35 +0000 (02:25 +0000)]
OMAP5: board: Add pinmux data for omap5_evm board.
Adding the full pinmux data for OMAP5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
SRICHARAN R [Mon, 12 Mar 2012 02:25:34 +0000 (02:25 +0000)]
OMAP5: clocks: Change clock settings as required for ES1.0 silicon.
Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Enric Balletbò i Serra [Mon, 5 Mar 2012 11:32:16 +0000 (11:32 +0000)]
OMAP3: igep00x0: Reduce lines of code for IGEP-based boards.
This is rework on config files of IGEP-based boards with the aim to remove
duplicated code to be more maintainable. Basically this patch creates a
common configuration file for both boards and only sets the specific option
in the board config file.
On board files the hardcored mach type was replaced in favour of using the
CONFIG_MACH_TYPE option.
More than 200 duplicated lines have been deleted.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Nishanth Menon [Thu, 1 Mar 2012 14:17:39 +0000 (14:17 +0000)]
OMAP4: scale voltage of core before MPU scales
OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.
As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Nishanth Menon [Thu, 1 Mar 2012 14:17:38 +0000 (14:17 +0000)]
OMAP4460: TPS Ensure SET1 is selected after voltage configuration
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
|---------------| (SET1 default 1.4V)
| --------(programmed voltage)
| <- (This switch happens on mux7,pullup)
vdd_mpu(TPS) -----/ (OPP boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -----------------------/ (OPP boot voltage)
Problem 1) |<----- Tx ------>|
timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.
By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
-------- (programmed voltage)
vdd_mpu(TPS) ------------/ (Opp boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -------------/ (OPP boot voltage)
NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Nishanth Menon [Thu, 1 Mar 2012 14:17:37 +0000 (14:17 +0000)]
OMAP3+: Introduce generic logic for OMAP voltage controller
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.
With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.
NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Jonathan Solnit [Fri, 24 Feb 2012 11:30:18 +0000 (11:30 +0000)]
ARM:OMAP+:MMC: Add parameters to MMC init
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
David Purdy [Tue, 27 Mar 2012 16:01:09 +0000 (16:01 +0000)]
kirkwood: add support for Cloud Engines Pogoplug E02
This patch adds support for Cloud Engines Pogoplug E02
Information regarding the CE Pogoplug E02 board can be found at:
http://archlinuxarm.org/platforms/armv5/pogoplug-v2-pinkgray
Signed-off-by: Dave Purdy <david.c.purdy@gmail.com>
Cc: prafulla@marvell.com
Cc: albert.u.boot@aribaud.net
Luka Perkov [Tue, 17 Apr 2012 09:22:17 +0000 (09:22 +0000)]
kirkwood: add NAS62x0 board support
Add support for new boards RaidSonic ICY BOX NAS6210 and NAS6220.
NAS6210 has 1 SATA and 1 eSATA port while NAS6220 has 2 SATA ports.
More information about the boards can be found here:
http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7036
http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7515
Signed-off-by: Luka Perkov <uboot@lukaperkov.net>
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Vladimir Zapolskiy [Thu, 19 Apr 2012 04:33:10 +0000 (04:33 +0000)]
devkit3250: add Timll DevKit3250 board initial support
This change adds a basic support for Embest/Timll DevKit3250 board,
NOR and UART are the only supported peripherals for a moment. The board
doesn't require low-level init, because the initial SDRAM and GPIO
configuration is performed during kickstart bootloader execution.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Vladimir Zapolskiy [Thu, 19 Apr 2012 04:33:09 +0000 (04:33 +0000)]
serial: add LPC32X0 high-speed UART devices support
This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Vladimir Zapolskiy [Thu, 19 Apr 2012 04:33:08 +0000 (04:33 +0000)]
arm926ejs: add NXP LPC32x0 cpu series support
This change adds initial support for NXP LPC32x0 SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Ian Campbell [Mon, 27 Feb 2012 21:19:02 +0000 (21:19 +0000)]
ARM: dreamplug: Enable FDT support
I have tested booting both FDT and non-FDT based Linux kernels (based on
http://marc.info/?l=linux-arm-kernel&m=
133002679716986 and
http://marc.info/?l=linux-arm-kernel&m=
132328894303581 respectively).
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Jason <jason@lakedaemon.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Wolfgang Denk [Mon, 30 Apr 2012 16:19:28 +0000 (18:19 +0200)]
Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lin_gadget: use common linux/compat.h
linux/compat.h: rename from linux/mtd/compat.h
lin_gadget: use common mdelay
gunzip: rename z{alloc, free} to gz{alloc, free}
fs/fat: align disk buffers on cache line to enable DMA and cache
part_dos: align disk buffers on cache line to enable DMA and cache
Wolfgang Denk [Mon, 30 Apr 2012 14:55:37 +0000 (16:55 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/ppc4xx: Remove typedefs for gdsys FPGA
powerpc/ppc4xx: Fix typo in gdsys_fpga.h
powerpc/ppc4xx: Update gdsys board configurations
powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
powerpc/ppc4xx: Adjust environment size on neo
Wolfgang Denk [Mon, 30 Apr 2012 14:55:25 +0000 (16:55 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
* 'master' of git://git.denx.de/u-boot-ppc4xx:
powerpc/ppc4xx: Remove typedefs for gdsys FPGA
powerpc/ppc4xx: Fix typo in gdsys_fpga.h
powerpc/ppc4xx: Update gdsys board configurations
powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
powerpc/ppc4xx: Adjust environment size on neo
Mike Frysinger [Thu, 26 Apr 2012 02:34:44 +0000 (02:34 +0000)]
lin_gadget: use common linux/compat.h
Merge our duplicate definitions with the common header.
Also fix drivers/usb/gadget/s3c_udc_otg_xfer_dma.c to
use min() instead of min_t() since we remove the latter
from compat.h.
Additionally use memalign() directly as the lin_gadget
specific kmalloc() macro is removed from lin_gadget_compat.h
by this patch.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Mike Frysinger [Mon, 9 Apr 2012 13:39:55 +0000 (13:39 +0000)]
linux/compat.h: rename from linux/mtd/compat.h
This lets us use it in more places than just mtd code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 9 Apr 2012 13:39:54 +0000 (13:39 +0000)]
lin_gadget: use common mdelay
No need to provide our own mdelay() macro when we have a func for it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 9 Apr 2012 13:39:53 +0000 (13:39 +0000)]
gunzip: rename z{alloc, free} to gz{alloc, free}
This allows us to add a proper zalloc() func (one that does a zeroing
alloc), and removes duplicate prototypes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Eric Nelson [Wed, 11 Apr 2012 04:08:53 +0000 (04:08 +0000)]
fs/fat: align disk buffers on cache line to enable DMA and cache
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Eric Nelson [Sat, 3 Mar 2012 12:02:20 +0000 (12:02 +0000)]
part_dos: align disk buffers on cache line to enable DMA and cache
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Andy Fleming [Tue, 24 Apr 2012 19:33:51 +0000 (19:33 +0000)]
Allow for parallel builds and saved output
The MAKEALL script cleverly runs make with the appropriate options
to use all of the cores on the system, but your average U-Boot build
can't make much use of more than a few cores. If you happen to have
a many-core server, your builds will leave most of the system idle.
In order to make full use of such a system, we need to build multiple
targets in parallel, and this requires directing make output into
multiple directories. We add a BUILD_NBUILDS variable, which allows
users to specify how many builds to run in parallel.
When BUILD_NBUILDS is set greater than 1, we redefine BUILD_DIR for
each build to be ${BUILD_DIR}/${target}. Also, we make "./build" the
default BUILD_DIR when BUILD_NBUILDS is greater than 1.
MAKEALL now tracks which builds are still running, and when one
finishes, it starts a new build.
Once each build finishes, we run "make tidy" on its directory, to reduce
the footprint.
As a result, we are left with a build directory with all of the built
targets still there for use, which means anyone who wanted to use
MAKEALL as part of a test harness can now do so.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Wolfgang Denk [Mon, 30 Apr 2012 14:45:59 +0000 (16:45 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
Wolfgang Denk [Mon, 30 Apr 2012 14:45:56 +0000 (16:45 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
Wolfgang Denk [Mon, 30 Apr 2012 14:43:52 +0000 (16:43 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
Wolfgang Denk [Mon, 30 Apr 2012 14:43:49 +0000 (16:43 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
* 'master' of git://git.denx.de/u-boot-i2c:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
Wolfgang Denk [Mon, 30 Apr 2012 14:41:25 +0000 (16:41 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
Blackfin: bfin_sdh: drop dos part hardcode
Blackfin: move gd/bd to bss by default
Blackfin: gd_t: relocate volatile markings
Wolfgang Denk [Mon, 30 Apr 2012 14:41:23 +0000 (16:41 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: bfin_sdh: drop dos part hardcode
Blackfin: move gd/bd to bss by default
Blackfin: gd_t: relocate volatile markings
Mike Frysinger [Sun, 22 Apr 2012 06:59:06 +0000 (06:59 +0000)]
image/fit: drop inline markings on parser code
Putting "inline" on extern funcs makes no sense, so drop them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Mon, 30 Apr 2012 14:29:16 +0000 (16:29 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nds32
* 'master' of git://git.denx.de/u-boot-nds32:
board/adp-ag102: add configuration of adp-ag102
board/adp-ag102: add board specific files
nds32/ag102: add ag102 soc support
nds32/ag102: add header support of ag102 soc
Dirk Eibach [Fri, 27 Apr 2012 08:33:46 +0000 (10:33 +0200)]
powerpc/ppc4xx: Remove typedefs for gdsys FPGA
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 26 Apr 2012 03:54:26 +0000 (03:54 +0000)]
powerpc/ppc4xx: Fix typo in gdsys_fpga.h
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 26 Apr 2012 03:54:25 +0000 (03:54 +0000)]
powerpc/ppc4xx: Update gdsys board configurations
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 26 Apr 2012 03:54:24 +0000 (03:54 +0000)]
powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
In hardware revision 1.20 one more fan controller is added to dlvision-10g.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Thu, 26 Apr 2012 03:54:23 +0000 (03:54 +0000)]
powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
Print fpga info at last_stage_init on gdsys 405ep boards.
Use dtt_init() to startup fans.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>