Chris Packham [Sat, 13 Apr 2019 08:35:24 +0000 (20:35 +1200)]
Remove whitelist entry for CONFIG_GPIO
CONFIG_GPIO does not exist. There is one hit for it in tegra_gpio.c but
it is a variable name.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Packham [Sat, 13 Apr 2019 08:35:23 +0000 (20:35 +1200)]
sysreset: select DM_GPIO instead of GPIO
CONFIG_GPIO does not exist. sysreset_gpio.c uses the DM gpio APIs so the
correct option to select is DM_GPIO.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 10 May 2019 11:07:49 +0000 (07:07 -0400)]
Merge branch '2019-05-09-master-imports'
- Minor fixes (ata memory leak, implement feedback on ohci-da8xx
changes, avb test fix, mmc test fix, spelling fixes, make FIT really
optional, fit-dtb blob cleanups, TI K3 workflow improvements, bootz
can boot barebox on 32bit ARM).
Lokesh Vutla [Thu, 2 May 2019 10:05:52 +0000 (15:35 +0530)]
remoteproc: k3_system_controller: Increase rx timeout
There is one case where 400ms is not sufficient for loading the
system firmware:
- System firmware is not signed with rsa degenerate key.
- ROM loading the sysfw directly from SPI flash which is in memory
mapped mode.
The above scenario is definitely not desired in production use cases
as it effects boot time. But still keeping this support as this is
a valid boot scenario.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Thu, 2 May 2019 10:05:51 +0000 (15:35 +0530)]
arm: k3: config.mk: Use k3_gen_x509_cert.sh to generate boot images
Instead of overlading makefile, use the k3_gen_x509_cert.sh script
to generate boot images.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Thu, 2 May 2019 10:05:50 +0000 (15:35 +0530)]
tools: k3_get_x509 cert: Add a script to generate x509 certificate for K3 devices
TI's K3 boot architecture mandates a x509 certificate for every boot image.
While signing the image K3 ROM allows for two types of keys based on which
the boot image gets loaded in different ways:
- Degenerate RSA keys: This generates a signature which is equal to the digest.
When ROM sees this, it does a DMA for copying the images,
which significantly improves the boot time.
- Any other key: Does a memcpy to load the image. This is introduced as a
fallback for DMA copy.
Add a script for generating boot images with the above options. Default
generates image using rsa degenerate key in order to improve boot time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Vagrant Cascadian [Thu, 2 May 2019 18:14:12 +0000 (11:14 -0700)]
Set time and umask on fit-dtb.blob to ensure reproducibile builds.
Support for compressed fit-dtb.blob was added in:
commit
95f4bbd581cf ("lib: fdt: Allow LZO and GZIP DT compression in
U-Boot")
When building compressed (lzop, gzip) fit-dtb.blob images, the
compression tool may embed the time or umask in the image.
Work around this by manually setting the time of the source file using
SOURCE_DATE_EPOCH and a hard-coded 0600 umask.
With gzip, this could be accomplished by using -n/--no-name, but lzop
has no current workaround:
https://bugs.debian.org/896520
This is essentially the same fix applied to multi-dtb fit SPL images in:
commit
8664ab7debab ("Set time and umask on multi-dtb fit images to
ensure reproducibile builds.")
Signed-off-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Vagrant Cascadian [Thu, 2 May 2019 18:14:11 +0000 (11:14 -0700)]
Remove fit-dtb.blob* in clean target.
Support for compressed fit-dtb.blob was added in:
commit
95f4bbd581cf ("lib: fdt: Allow LZO and GZIP DT compression in
U-Boot")
Adjust Makefile to also clean compressed blobs.
Signed-off-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Vagrant Cascadian [Thu, 2 May 2019 18:14:10 +0000 (11:14 -0700)]
Add fit-dtb.blob* to .gitignore.
Support for compressed fit-dtb.blob was added in:
commit
95f4bbd581cf ("lib: fdt: Allow LZO and GZIP DT compression in
U-Boot")
Adjust .gitignore to also exclude compressed blobs.
Signed-off-by: Vagrant Cascadian <vagrant@reproducible-builds.org>
Christoph Fritz [Fri, 3 May 2019 11:19:49 +0000 (13:19 +0200)]
arm: zimage: add barebox image magic number
For chainboot configurations or test environments, this patch allows
booting barebox images by using command bootz.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Stephen Warren [Tue, 16 Apr 2019 22:04:49 +0000 (16:04 -0600)]
test/py: don't use mmc_rd config for other mmc tests
Fix test_mmc_dev(), test_mmc_rescan(), test_mmc_info() not to use the
same configuration data that test_mmc_rd() does. Doing so causes the
following issues:
* The new code uncondtionally expects certain keys to exist in the
configuration data. These keys do not exist in existing configuration
data since they were not previously required, and there was no
notification re: a requirement to add these new keys. This causes test
failures due to thrown exceptions when accessing the non-existent keys.
* The new tests logically operate on different objects. test_mmc_rd()
operates on ranges of sectors on an MMC device (which may be the entire
set of sectors of a device, or a part of a device), whereas all the new
tests operate solely on entire devices. These are separate things, and
it's entirely likely that the user will wish to runs the two types of
tests on different sets of data; see the example configuration data that
this commit adds. Ideally, the new tests would have been added to a
separate Python file, since they aren' closely related to the existing
tests.
FIXME: Marek, can you please replace the "???" in this patch with some
reasonable looking data? Thanks.
Cc: Marek Vasut <marek.vasut@gmail.com>
Fixes:
4ffec8cdf512 ("test/py: mmc: Add 'mmc info' test")
Fixes:
ce4b2cafa79c ("test/py: mmc: Add 'mmc rescan' test")
Fixes:
86dfd152c917 ("test/py: mmc: Add 'mmc dev' test")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Simon Goldschmidt [Fri, 3 May 2019 19:19:03 +0000 (21:19 +0200)]
fdt_shrink_to_minimum: do not mark fdt space reserved unconditionally
This function merely relocates the fdt blob, so don't let it alter
it by adding reservations that didn't exist before.
Instead, if the memory used for the fdt blob has been reserved
before calling this function, ensure the relocated memory is
marked as reserved instead.
Reported-by: Keerthy <j-keerthy@ti.com>
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Fabrice Fontaine [Fri, 3 May 2019 20:37:05 +0000 (22:37 +0200)]
Make FIT support really optional
Due to some mistakes in the source code, it was not possible to really
turn FIT support off. This commit fixes the problem by means of the
following changes:
- Enclose "bootm_host_load_image" and "bootm_host_load_images" between
checks for CONFIG_FIT_SIGNATURE, in common/bootm.c.
- Enclose the declaration of "bootm_host_load_images" between checks for
CONFIG_FIT_SIGNATURE, in common/bootm.h.
- Condition the compilation and linking of fit_common.o fit_image.o
image-host.o common/image-fit.o to CONFIG_FIT=y, in tools/Makefile.
Signed-off-by: Carlos Santos <casantos@datacom.ind.br>
[fabio: adapt for 2016.07]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Ricardo: fix conditional compilation and linking of the files mentioned above
for 2016.07]
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
[Jörg: adapt for 2019.01]
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
[Retrieved from:
https://git.buildroot.net/buildroot/tree/package/uboot-tools/0003-Make-FIT-support-really-optional.patch]
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Vagrant Cascadian [Fri, 3 May 2019 22:28:37 +0000 (14:28 -0800)]
Fix spelling of available.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Sat, 4 May 2019 17:10:05 +0000 (19:10 +0200)]
env: spi: Fix incorrect entry description
Fix the max frequency entry description, it's incorrect.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Rini <trini@konsulko.com>
Igor Opaniuk [Mon, 6 May 2019 09:07:31 +0000 (12:07 +0300)]
test/py: avb: fix test_avb_persistent_values fail
Fix test_avb_persistent_values() pytest, which was failing because of
wrong size value provided from tee sandbox driver.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Christian Gmeiner [Mon, 6 May 2019 13:18:54 +0000 (15:18 +0200)]
ata: ahci: fix memory leak
malloc(..) and memalign(..) are both allocating memory and as a result
we leak the memory allocated with malloc(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Tue, 7 May 2019 11:57:39 +0000 (06:57 -0500)]
usb: ohci: ohci-da8xx: Cleanup Error handling and fix flags
Per feedback from Marek, he suggested better handling and
to enable DM_FLAG_OS_PREPARE, this patch re-orders some of
the error checking, and errors returns the error code right
away and also sets DM_FLAG_OS_PREPARE.
Signed-off-by: Adam Ford <aford173@gmail.com>
Stefan Roese [Thu, 9 May 2019 08:16:20 +0000 (10:16 +0200)]
dm: MIGRATION: Add migration plan for WDT (DM watchdog support)
As much of the watchdog system has been migrated to DM now, formalize a
deadline for migration.
Please note that the old CONFIG_HW_WATCHDOG macro should be removed
completely at some point.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 9 May 2019 11:12:51 +0000 (07:12 -0400)]
Merge tag 'rockchip-for-v2019.07-rc1' of git://git.denx.de/u-boot-rockchip
Improvements and new features:
- split more rockchip pinctrl_core feature into per SoC
- enable TPL for evb-rk3399 board
- enable TPL/SPL for evb-px5 board
- enable TPL and OP-TEE support for evb-rk3229
- update fix in arm common assembly start code for rockchip header file
- update default SPL_FIT_GENERATOR for rockchip
- rk3399 boards update to use '-u-boot.dtsi'
- add new rk3399 boards: Nanopi M4, Nanopc T4
- enable sound for chromebook_minnie
Tom Rini [Thu, 9 May 2019 11:12:25 +0000 (07:12 -0400)]
Merge git://git.denx.de/u-boot-marvell
- DM updates for multiple MVEBU boards (Stefan)
- Add CRS305-1G-4S board (Luka)
- Enable MMC in SPL on clearfog (Baruch)
Tom Rini [Thu, 9 May 2019 11:11:52 +0000 (07:11 -0400)]
Merge git://git.denx.de/u-boot-riscv
- Correct SYS_TEXT_BASE for qemu.
- Support booti.
- Increase SYSBOOTM_LEN for Fedora/RISCV kernel.
- Support SMP booting from flash.
Tom Rini [Thu, 9 May 2019 11:11:39 +0000 (07:11 -0400)]
Merge tag 'u-boot-amlogic-
20190509' of git://git.denx.de/u-boot-amlogic
- Add USB PHY drivers for Amlogic G12A
- Add USB Complex Glue driver for Amlogic G12A
- Add USB Gadget support for Amlogic G12A
Jagan Teki [Wed, 8 May 2019 05:41:51 +0000 (11:11 +0530)]
doc: rockchip: Add global doc for rk3399 build/flash
Since rockchip have an individual doc/README.rockchip, it would
be better to update the same instead of maintaining it separately
in board files.
So, add the documentation for rk3399
- procedure to build for Rockchip miniloader and
U-Boot SPL options
- procedure to boot from SD for Rockchip miniloader and
U-Boot SPL options
- procedure to build ATF, PMU M0 firmware for puma boards
- add boot logs of each option, so-that it would help for future
boards porting
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Wed, 8 May 2019 05:41:47 +0000 (11:11 +0530)]
rockchip: rk3399: Add Nanopc T4 board support
Add initial support for Nanopc T4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- 16GB eMMC
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-nanopc-t4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Add NanoPC-T4 IR receiver"
(sha1:
95658e21b1707ad7844f873db2fdaa295109a5a3)
Tested-by: Daniel Gröber <dxld@darkboxed.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Wed, 8 May 2019 05:41:46 +0000 (11:11 +0530)]
rockchip: rk3399: Add Nanopi M4 board support
Add initial support for Nanopi M4 board.
Specification
- Rockchip RK3399
- Dual-Channel 4GB LPDDR3-1866
- SD card slot
- eMMC socket
- RTL8211E 1Gbps
- AP6356S WiFI/BT
- HDMI In/Out, DP, MIPI DSI/CSI
- USB 3.0 x4
- USB Type C power and data
- GPIO1, GPIO2 expansion ports
- DC5V/3A
Commit details of rk3399-nanopi-m4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: Refine nanopi4 differences"
(sha1:
c62ffaf5026d0b7633e62b2cea8450b5543c349a)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jagan Teki [Wed, 8 May 2019 05:41:45 +0000 (11:11 +0530)]
rockchip: dts: rk3399: nanopi4: Use CD pin as RK_FUNC_1
Attaching GPIO functionality to SDMMC0_DET pin (which
does in Linux base dts) make dwmmc driver "fail to detect
the card".
Card did not respond to voltage select!
It may be because the existing driver can't support gpio
card detection. So, change the pinctrl functionality from
RK_FUNC_GPIO to RK_FUNC_1 like other rk3399 dts does via
sdmmc_cd pin.
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Atish Patra [Tue, 7 May 2019 00:49:39 +0000 (17:49 -0700)]
RISCV: image: Add booti support
This patch adds booti support for RISC-V Linux kernel. The existing
bootm method will also continue to work as it is.
It depends on the following kernel patch which adds the header to the
flat Image. Gzip compressed Image (Image.gz) support is not enabled with
this patch.
https://patchwork.kernel.org/patch/
10925543/
Tested on HiFive Unleashed and QEMU.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Karsten Merker <merker@debian.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Rick Chen [Tue, 30 Apr 2019 05:49:37 +0000 (13:49 +0800)]
riscv: configs: AE350 will use CONFIG_OF_SEPARATE when boots from flash
When AE350 boots from flash, use CONFIG_OF_SEPARATE instead of
CONFIG_OF_BOARD.
Also remove unused code about prior_stage_fdt_address.
And modify CONFIG_SYS_FDT_BASE as flash address.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 30 Apr 2019 05:49:36 +0000 (13:49 +0800)]
riscv: configs: AE350 will use CONFIG_OF_PRIOR_STAGE when boots from ram
When AE350 boots from ram, use CONFIG_OF_PRIOR_STAGE instead
of CONFIG_OF_BOARD.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 30 Apr 2019 05:49:35 +0000 (13:49 +0800)]
riscv: prior_stage_fdt_address should only be used when OF_PRIOR_STAGE is enabled
This patch will fix prior_stage_fdt_address write failure problem, when
AE350 boots from flash.
When AE350 boots from flash, prior_stage_fdt_address will be flash
address, we shall avoid it to be written.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Thu, 9 May 2019 02:20:19 +0000 (10:20 +0800)]
riscv: configs: Support AE350 SMP booting from flash flow
Add two defconfigs to support AE350 SMP booting from flash.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Rick Chen [Tue, 30 Apr 2019 05:49:33 +0000 (13:49 +0800)]
riscv: Introduce CONFIG_XIP to support booting from flash
When U-Boot boots from flash, during the boot process,
hart_lottery and available_harts_lock variable addresses
point to flash which is not writable. This causes boot
failures on AE350. Introduce a config option CONFIG_XIP
to support such configuration.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Anup Patel [Thu, 11 Apr 2019 06:52:12 +0000 (06:52 +0000)]
riscv: qemu: Use correct SYS_TEXT_BASE for S-mode on 32bit system
For 32bit system, the OpenSBI (or BBL) will jump to 0x80400000 address
in S-mode whereas for 64bit system it will jump to 0x80200000 address
in S-mode.
Currently, the S-mode U-Boot sets SYS_TEXT_BASE to 0x80200000 for both
32bit and 64bit system. This breaks S-mode U-Boot for 32bit system.
This patch sets different SYS_TEXT_BASE for 32bit and 64bit system so
that S-mode U-Boot works fine for both.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Karsten Merker <merker@debian.org>
David Abdurachmanov [Tue, 9 Apr 2019 10:42:47 +0000 (12:42 +0200)]
riscv: qemu-riscv.h: define CONFIG_PREBOOT (enables extlinux)
- Set fdt_addr variable, which is needed for extlinux to find FDT.
Otherwise booting kernel using extlinux results in missing FDT.
- Also run fdt addr with FDT address so that fdt commands would
work out of the box in U-Boot prompt.
This is successfully used by Fedora/RISCV with 5.1-rc3+ kernel using
OpenSBI -> U-Boot (S-mode) [extlinux] -> Kernel setup.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
David Abdurachmanov [Tue, 9 Apr 2019 10:42:46 +0000 (12:42 +0200)]
riscv: set CONFIG_SYS_BOOTM_LEN to SZ_64M
After updating Fedora/RISCV kernel to 5.1-rc3+ the size increased above
the current threshold. Looking into HiKey, Dragonboards, etc. seems that
SZ_64M is a popular option.
This sucessfully boots Fedora/RISCV with 5.1-rc3+ kernel on QEMU 4.0 (master)
with OpenSBI -> U-Boot (S-mode) [extlinux] -> Kernel setup.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Neil Armstrong [Tue, 19 Feb 2019 13:21:04 +0000 (14:21 +0100)]
mach-meson: g12a: add DWC2 peripheral mode support
Adds support for Amlogic G12A USB Device mode.
The DWC2 Controller behind the Glue can be connected to an OTG
capable PHY. The Glue setups the PHY mode.
This patch implements Device mode support by adding a board_usb_init/cleanup
setting up the DWC2 controller and switch the OTG capable port to Device
before starting the DWC2 controller in Device mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 19 Feb 2019 14:17:29 +0000 (15:17 +0100)]
phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
This adds support for the USB PHYs found in the Amlogic G12A SoC Family.
The USB2 PHY supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on
the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 19 Feb 2019 12:42:01 +0000 (13:42 +0100)]
usb: dwc3: Add Meson G12A USB Glue
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Baruch Siach [Wed, 8 May 2019 14:47:32 +0000 (17:47 +0300)]
arm: mvebu: clearfog: add MMC to SPL DT
This allows SPL to load the main U-Boot image from MMC once DM_MMC is
enabled.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Luka Kovacic [Tue, 7 May 2019 17:35:55 +0000 (19:35 +0200)]
arm: mvebu: Add CRS305-1G-4S board
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 3 May 2019 06:42:19 +0000 (08:42 +0200)]
arm: mvebu: db-88f6820-gp: Enable BLK and DM support
This patch enables CONFIG_BLK and some DM enabled drivers on
db-88f6820-gp to remove these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Stefan Roese [Fri, 3 May 2019 06:42:18 +0000 (08:42 +0200)]
arm: mvebu: db-88f6720: Enable CONFIG_BLK
This patch enables CONFIG_BLK to remove this compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 3 May 2019 06:42:17 +0000 (08:42 +0200)]
arm: mvebu: clearfog: Enable BLK and DM support
This patch enables CONFIG_BLK and some DM enabled drivers on clearfog
to remove these compile warnings:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
the board to use CONFIG_DM_MMC before the v2019.04 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Thu, 9 May 2019 02:46:31 +0000 (22:46 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-net
- Various PHY fixes / enhancements.
- TI K2G fixes
James Byrne [Mon, 4 Mar 2019 17:40:34 +0000 (17:40 +0000)]
net: phy: micrel: Find Micrel PHY node correctly
In some of the device trees that specify skew values for KSZ90x1 PHYs
the values are stored (incorrectly) in the MAC node, whereas in others
it is in an 'ethernet-phy' subnode. Previously the code would fail to
find and program these skew values, so this commit changes it to look
for an "ethernet-phy" subnode first, and revert to looking in the MAC
node if there isn't one.
The device trees affected (where the skew values are in a subnode) are
imx6qdl-icore-rqs.dtsi, r8a77970-eagle.dts, r8a77990-ebisu.dts,
r8a77995-draak.dts, salvator-common.dtsi, sama5d3xcm.dtsi,
sama5d3xcm_cmp.dtsi, socfpga_cyclone5_vining_fpga.dts,
socfpga_stratix10_socdk.dts and ulcb.dtsi. Before this change the skew
values in these device trees would be ignored.
The device trees where the skew values are in the MAC node are
socfpga_arria10_socdk.dtsi, socfpga_arria5_socdk.dts,
socfpga_cyclone5_de0_nano_soc.dts, socfpga_cyclone5_de10_nano.dts,
socfpga_cyclone5_de1_soc.dts, socfpga_cyclone5_is1.dts,
socfpga_cyclone5_socdk.dts, socfpga_cyclone5_sockit.dts. These should be
unaffected by this change.
The changes were tested on a sama5d3xcm.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
James Byrne [Mon, 4 Mar 2019 17:40:33 +0000 (17:40 +0000)]
net: phy: micrel: Use correct skew values on KSZ9021
Commit
ff7bd212cb8a ("net: phy: micrel: fix divisor value for KSZ9031
phy skew") fixed the skew value divisor for the KSZ9031, but left the
code using the same divisor for the KSZ9021, which is incorrect.
The preceding commit
c16e69f702b1 ("net: phy: micrel: add documentation
for Micrel KSZ90x1 binding") added the DTS documentation for the
KSZ90x1, changing it from the equivalent file in the Linux kernel to
correctly state that for this part the skew value is set in 120ps steps,
whereas the Linux documentation and driver continue to this day to use
the incorrect value of 200 that came from the original KSZ9021 datasheet
before it was corrected in revision 1.2 (Feb 2014).
This commit sorts out the resulting confusion in a consistent way by
making the following changes:
- Update the documentation to be clear about what the skew values mean,
in the same was as for the KSZ9031.
- Update the Micrel PHY driver to select the appropriate divisor for
both parts.
- Adjust all the device trees that state skew values for KSZ9021 PHYs to
use values based on 120ps steps instead of 200ps steps. This will result
in the same values being programmed into the skew registers as the
equivalent device trees in the Linux kernel do, where it incorrectly
uses 200ps steps (since that's where all these device trees were copied
from).
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Valentin-catalin Neacsu [Wed, 13 Feb 2019 09:14:53 +0000 (09:14 +0000)]
net: phy: aquantia: Set only autoneg on in register 4.c441
For AQR405 in register 4.c441 bit 15 was override with 0. This caused the
phy to not negotiate at 2.5GB rate with mac. To avoid
this override it needed first to know the previous value of reg 4.c441
and set only bit 3.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Siva Durga Prasad Paladugu [Mon, 4 Mar 2019 15:02:11 +0000 (16:02 +0100)]
net: phy: Fix return value check phy_probe
Don't ignore return value of phy_probe() call as
the probe may fail and it needs to be reported.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Siva Durga Prasad Paladugu [Mon, 4 Mar 2019 15:01:30 +0000 (16:01 +0100)]
net: phy: Reloc next and prev pointers inside phy_drivers
This patch relocates the pointers inside phy_drivers incase
of manual reloc. Without this reloc, these points to invalid
pre relocation address and hence causes exception or hang.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Murali Karicheri [Mon, 25 Feb 2019 20:27:34 +0000 (15:27 -0500)]
ARM: k2g-ice: Add pinmux support for rgmii interface
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Murali Karicheri [Mon, 25 Feb 2019 20:27:33 +0000 (15:27 -0500)]
ARM: k2g-gp-evm: update to rgmii pinmux configuration
This patch updates pinmux configuration for K2G GP EVM based on
data generated by the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pankaj Bansal [Fri, 8 Feb 2019 08:46:11 +0000 (08:46 +0000)]
drivers: net: ldpaa_eth: fix resource leak
if an error occurs in ldpaa_eth_init, need to free all resources
before returning the error.
Threfore, free net_dev before returning from ldpaa_eth_init.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Wed, 8 May 2019 20:21:43 +0000 (16:21 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi
- H6 Beelink GS1 board (Clément)
- Olimex A64-Teres-I board (Jonas)
- sunxi build fix for CONFIG_CMD_PXE|DHCP (Ondrej)
- Change include order (Jagan)
- EPHY clock changes (Jagan)
- EMAC enablement on Cubietruck Plus, BPI-M3 (Chen-Yu Tsai)
Chen-Yu Tsai [Fri, 3 May 2019 02:27:41 +0000 (10:27 +0800)]
sunxi: Enable EMAC on the Bananapi M3
The Bananapi M3 has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DCDC1 through SW @ 3.3V.
The board is designed to use 3.3V with RGMII, instead of the standard
reduced voltage of 2.5V we see everywhere. DLDO3, which provides the
I/O voltages, is raised to match.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Chen-Yu Tsai [Fri, 3 May 2019 02:27:40 +0000 (10:27 +0800)]
sunxi: Enable EMAC on the Cubietruck Plus
The Cubietruck Plus has an RTL8211E PHY connected to the EMAC using
RGMII. The PHY is powered by DLDO4 @ 3.3V, while the I/O pins are
powered by DLDO3 @ 2.5V.
This patch enables the EMAC and Realtek PHY drivers in the defconfig.
The device tree file already has the EMAC enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Jonas Smedegaard [Sat, 20 Apr 2019 10:24:16 +0000 (18:24 +0800)]
sun50i: a64: Add Olimex A64-Teres-I board initial support
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.
Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)
Works:
- i2C
- MMC/SD
- PWM backlight
Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.
This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).
Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1:
d91ebb95b96c8840932dc3a10c9f243712555467)
Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.
config and .dtsi file are adapted from pinebook files.
Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 18:57:00 +0000 (00:27 +0530)]
net: sun8i_emac: Add EPHY CLK and RESET support
Add EPHY CLK and RESET support for sun8i_emac driver to
enable EPHY TX clock and EPHY reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Jagan Teki [Wed, 27 Feb 2019 18:56:56 +0000 (00:26 +0530)]
test/dm: reset: Add reset_get_by_index[_nodev] test
Add sample dm reset test for reset_get_by_index and
reset_get_by_index_nodev functionality code.
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 27 Feb 2019 18:56:55 +0000 (00:26 +0530)]
reset: Get the RESET by index without device
Getting a RESET by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process RESET operation for child
without udevice but with ofnode.
So add reset_get_by_index_nodev() and move the common code
in reset_get_by_index_tail() to use for reset_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Tue, 5 Mar 2019 14:12:44 +0000 (19:42 +0530)]
test/dm: clk: Add clk_get_by_index[_nodev] test
Add sample dm clk test for clk_get_by_index and
clk_get_by_index_nodev functionality code.
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 27 Feb 2019 18:56:53 +0000 (00:26 +0530)]
clk: Use clk_get_by_index_tail()
clk_get_by_index_tail() now handle common clk get by index
code so use it from clk_get_by_indexed_prop().
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 18:56:52 +0000 (00:26 +0530)]
clk: Get the CLK by index without device
Getting a CLK by index with device is not straight forward
for some use-cases like handling clock operations for child
node in parent driver. So we need to process the child node
in parent probe via ofnode and process CLK operation for child
without udevice but with ofnode.
So add clk_get_by_index_nodev() and move the common code
in clk_get_by_index_tail() to use for clk_get_by_index()
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jagan Teki [Wed, 8 May 2019 14:26:16 +0000 (19:56 +0530)]
serial: sifive: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the serial_sifive driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/serial/serial_sifive.c:6:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in serial_sifive.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 8 May 2019 14:22:18 +0000 (19:52 +0530)]
clk: sifive: fu540-prci: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the fu540-prci driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/riscv/include/asm/u-boot.h:23:0,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from include/clk-uclass.h:13,
from drivers/clk/sifive/fu540-prci.c:32:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in fu540-prci.c to include first common.h file.
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 8 May 2019 14:12:16 +0000 (19:42 +0530)]
spi: atcspi200: Change include order
Like clk_get_by_index, there is requirement for
clk_get_by_index_nodev. In this case to make common
code functionalities for dev and nodev, clk_get_by_index
is trying to get the index of clock by passing ofnode
instead of actual dev like current gpio uclass does.
In these scenarios with current order of include files
the atcspi200_spi driver is unable to find CONFIG_ENV_SIZE.
In file included from arch/nds32/include/asm/u-boot.h:24,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/clk.h:11,
from drivers/spi/atcspi200_spi.c:9:
include/environment.h:145:19: error: 'CONFIG_ENV_SIZE'
undeclared here (not in a function); did you mean 'CONFIG_CMD_XIMG'?
#define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
So, fix consists of changing the order of include files
in atcspi200_spi.c to include first common.h file.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Wed, 8 May 2019 13:20:19 +0000 (09:20 -0400)]
Merge git://git.denx.de/u-boot-x86
- Allow x86 boards to use TPL, SPL and U-Boot proper
- Update sysreset x86 driver to utilize ACPI registers to do power off
- Add a new chromebook_samus_tpl board for TPL support
- Several minor changes in binman tool
Tom Rini [Wed, 8 May 2019 13:20:04 +0000 (09:20 -0400)]
Merge tag 'efi-2019-07-rc2-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc2 (2)
Fix a bunch of errors in the UEFI sub-system:
* implement missing UnloadImage(),
* implement missing RegisterProtocolNotify(),
* unload images in Exit(),
* parameter checks.
Provide a unit test for UnloadImage().
Remove a redundant function for unit tests.
Clean up the UEFI sub-system initialization
Jagan Teki [Wed, 8 May 2019 05:41:44 +0000 (11:11 +0530)]
rockchip: dts: rk3399: Sync rk3399-nanopi4.dtsi from Linux
Sync rk3399-nanopi4.dtsi from Linux 5.1-rc2 tag.
Linux commit details about the rk3399-nanopi4.dtsi sync:
"arm64: dts: rockchip: Add nanopi4 bluetooth"
(sha1:
3e2f0bb72be36aa6c14ee7f11ac4dd8014801030)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Wed, 8 May 2019 05:41:43 +0000 (11:11 +0530)]
arm: rockchip: rk3399: Move common configs in Kconfig
Few SPL and U-Boot proper configs are common to all rk3399 target
defconfigs, move them and select it from platform kconfig.
Moved configs:
- SPL_ATF
- SPL_ATF_NO_PLATFORM_PARAM if SPL_ATF
- SPL_LOAD_FIT
- SPL_CLK if SPL
- SPL_PINCTRL if SPL
- SPL_RAM if SPL
- SPL_REGMAP if SPL
- SPL_SYSCON if SPL
- CLK
- FIT
- PINCTRL
- RAM
- REGMAP
- SYSCON
- DM_PMIC
- DM_REGULATOR_FIXED
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Wed, 8 May 2019 05:41:42 +0000 (11:11 +0530)]
Kconfig: Add default SPL_FIT_GENERATOR for rockchip
Add default SPL_FIT_GENERATOR py script for rockchip platforms if
specific target enabled SPL_LOAD_FIT.
So, this would help get rid of explicitly mentioning the default
SPL FIT generator in defconfigs. however some targets, like puma_rk3399
still require their own FIT generator so in those cases the default will
override with defconfig defined generator.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Wed, 8 May 2019 05:41:41 +0000 (11:11 +0530)]
rockchip: dts: rk3399: Sync pwm2_pin_pull_down from Linux 5.1-rc2
To make successful build with dts(i) files syncing from Linux 5.1-rc2
the rk3399.dtsi would require pwm2_pin_pull_down.
So, sync the pwm2_pin_pull_down node from Linux 5.1-rc2. Since this
node is strictly not part of any commit alone, I have mentioned
Linux 5.1-rc2 tag for future reference of where would this sync
coming from.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 7 May 2019 18:24:40 +0000 (23:54 +0530)]
rockchip: rk3399: orangepi: Add SPL_TEXT_BASE
CONFIG_SPL_TEXT_BASE was available in configs/rk3399_common.h
when the OrangePI rk3399 board supported during first
version patch.
But, later below change which move this config into Kconfig and
same has been merged in mainline tree.
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1:
f89d6133eef2e068f9c33853b6584d7fcbfa9d2e)
Unfortunately, the maintainer applied the initial version patch,
instead of looking for next version changes.
Fix it by adding SPL_TEXT_BASE in orangepi-rk3399 defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 7 May 2019 18:21:52 +0000 (23:51 +0530)]
arm64: rockchip: dts: rk3399: Use rk3399-u-boot.dtsi
Now we have
- board specific -u-boot.dtsi files for board specific u-boot
dts changes.
- soc specific rk3399-u-boot.dtsi for soc specific u-boot
dts changes.
So, include the rk3399-u-boot-dtsi on respective board -u-boot.dtsi
and drop the properties which are globally available in rk3399-u-boot.dtsi
Right now rk3399-u-boot.dtsi has sdmmc, spi1 u-boot,dm-pre-reloc
property and more properties and nodes can be move further based
on the requirements.
This would fix, the -u-boot.dtsi inclusion for evb, firefly, puma
boards that was accidentally merged on below commit.
"rockchip: dts: rk3399: Create initial rk3399-u-boot.dtsi"
(sha1:
e05b4a4fa84b65a0c8873e8f34721741fe2bc09d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 7 May 2019 18:21:51 +0000 (23:51 +0530)]
rockchip: dts: rk3399-u-boot: Add u-boot, dm-pre-reloc for spi1
Add u-boot,dm-pre-reloc property for spi1, so-that the
subsequent rk3399 boards which boot from SPI.
This help to separate the u-boot specific properties away
from base dts files so-that the Linux sync become easy and
meaningful.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 7 May 2019 18:21:50 +0000 (23:51 +0530)]
arm64: rockchip: dts: rk3399: Add board -u-boot.dtsi files
Devicetree files in RK3399 platform is synced from Linux, like other
platforms does. Apart from these u-boot in rk3399 would also require
some u-boot specific node like dmc.
dmc node has big chunk of DDR timing parameters which are specific
to specific board, and maintained with rk3399-sdram*.dtsi.
So, create board specific -u-boot.dtsi files and move these sdram dtsi
files accordingly. This would help of maintain u-boot specific changes
separately without touching Linux dts(i) files which indeed easy for
syncing from Linux between releases.
These board specific -u-boot.dtsi can be extendible to add more u-boot
specific nodes or properties in future.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jagan Teki [Tue, 7 May 2019 18:21:49 +0000 (23:51 +0530)]
dts: Makefile: Build rockchip dtbs based on SoC types
- Sometimes u-boot specific dtsi files are included
automatically which would build for entire rockchip SoC,
even-though the respective dtsi should used it for specific
family of rockchip SoC.
- Sometimes u-boot specific dts nodes or properties can use
config macros from respective rockchip family include/configs
files, example CONFIG_SPL_PAD_TO.
So, it's better to compile the dtbs based on the respective
rockchip family types rather than rockchip itself to avoid
compilation issues.
This patch organize the existing dtb's based on the rockchip
family types.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:58:13 +0000 (21:58 +0800)]
pinctrl: rockchip: Also move common set_schmitter func into per Soc file
Only some Soc need Schmitter feature, so move the
implementation into their own files.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:57:54 +0000 (21:57 +0800)]
pinctrl: rockchip: Clean the unused type and label
As the mux/pull/drive feature implement at own file,
the type and label are not necessary.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:57:28 +0000 (21:57 +0800)]
pinctrl: rockchip: Special treatment for RK3288 gpio0 pins' pull
RK3288 pmu_gpio0 pull setting have no higher 16 writing corresponding
bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:57:05 +0000 (21:57 +0800)]
pinctrl: rockchip: Split the common set_pull() func into per Soc
As the common set_mux func(), implement the feature at the own file
for each Soc.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:56:34 +0000 (21:56 +0800)]
pinctrl: rockchip: Special treatment for RK3288 gpio0 pins' drive strength
RK3288 pmu_gpio0 drive strength setting have no higher 16 writing
corresponding bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:55:26 +0000 (21:55 +0800)]
pinctrl: rockchip: Split the common set_drive() func into per Soc
As the common set_mux func(), implement the feature at the own file
for each Soc.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:50:56 +0000 (21:50 +0800)]
pinctrl: rockchip: Special treatment for RK3288 gpio0 pins' iomux
RK3288 pmu_gpio0 iomux setting have no higher 16 writing corresponding
bits, need to read before write the register.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:50:55 +0000 (21:50 +0800)]
pinctrl: rockchip: Split the common set_mux() into per Soc
Such as rk3288's pins of pmu_gpio0 are a special feature, which have no
higher 16 writing corresponding bits, use common set_mux() func would
introduce more code, so implement their set_mux() in each Soc's own
file to reduce the size of code.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:50:54 +0000 (21:50 +0800)]
pinctrl: rockchip: Remove redundant spaces
Some files have the redundant spaces, remove them.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
David Wu [Tue, 16 Apr 2019 13:50:53 +0000 (21:50 +0800)]
pinctrl: rockchip: Add pull-pin-default param and remove unused param
Some Socs use the pull-pin-default config param, need to add it.
And input-enable/disable config params are not necessary, remove it.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Tue, 7 May 2019 01:36:32 +0000 (09:36 +0800)]
Revert "pinctrl: rockchip: Add 32bit writing function for rk3288 gpio0 pinctrl"
This reverts commit
502980914b2d6f9ee85a823aa3ef9ead76c0b7f2.
This is a superseded version, revert this to apply new patch set.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Simon Glass [Sat, 27 Apr 2019 01:03:39 +0000 (19:03 -0600)]
rockchip: chromebook_minnie: Enable sound
Enable sound for this board, which has the same codec as jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 9 Nov 2018 03:21:38 +0000 (11:21 +0800)]
rockchip: rk3399: update defconfig for TPL
The SPL is now running at SDRAM, and 0x10000 is used by BL31,
and the ARM SPL do not support relocate now, we need reserved
0x50000 so that it won't overwrite the code when we load the
bl31 to target space.
We should remove this after we enable the relocate feature.
The SPL need malloc 0x9000 for MMC as buffer used for transfer
data to IRAM(The EMMC DMA can not transfer data to IRAM directly).
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 1 Apr 2019 09:20:53 +0000 (17:20 +0800)]
rockchip: ram: rk3399: update for TPL
Init the ddr sdram in TPL instead of SPL, update the code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Kever Yang [Fri, 9 Nov 2018 03:18:15 +0000 (11:18 +0800)]
rockchip: rk3399: add tpl support
Rockchip platform suppose to use TPL(run in SRAM) as dram init and
SPL(run in DDR SDRAM) as pre-loader, so that the SPL would not be
limited by SRAM size.
This patch add rk3399-board-tpl.c and its common configs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Mon, 1 Apr 2019 09:15:53 +0000 (17:15 +0800)]
rockchip: add u-boot-tpl-v8.lds
We don't have both sram and sdram in TPL, so update from:
arch/arm/cpu/armv8/u-boot-spl.lds
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 29 Mar 2019 14:48:31 +0000 (22:48 +0800)]
rockchip: px5: add timer0 dts node as tick timer
Let's use rockchip timer before stimer patches can be merged.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 29 Mar 2019 14:48:30 +0000 (22:48 +0800)]
rockchip: rk3368: remove uart iomux init in SPL
The iomux should have been set in board_debug_uart_init(),
do not set in board_init_f(), remove it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 29 Mar 2019 14:48:29 +0000 (22:48 +0800)]
rockchip: dmc: rk3368: update rank number for evb-px5
evb-px5 has only 1 CS, update for it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Kever Yang [Fri, 29 Mar 2019 14:48:28 +0000 (22:48 +0800)]
rockchip: boot0: update CONFIG_ROCKCHIP_SPL_RESERVE_IRAM for SPL only
The CONFIG_ROCKCHIP_SPL_RESERVE_IRAM is for SPL only, add
condition to limit it not affect TPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Tue, 12 Feb 2019 07:19:07 +0000 (15:19 +0800)]
rockchip: px5: update defconfig for TPL/SPL
Add options to support TPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 29 Mar 2019 14:48:26 +0000 (22:48 +0800)]
rockchip: px5: update SPL size for spl/tpl
Use larger space for load bl31 in SPL
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Kever Yang [Fri, 29 Mar 2019 14:48:25 +0000 (22:48 +0800)]
rockchip: px5 update dts for spl/tpl
TPL need dmc to init ddr sdram, and emmc, boot-order.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>