review.tizen.org Git - platform/kernel/linux-rpi.git/log

ARM: dts: imx6: phycore-som: fix emmc supply

commit eb0bbba7636b9fc81939d6087a5fe575e150c95a upstream.

Currently the vmmc is supplied by the 1.8V pmic rail but this is wrong.
The default module behaviour is to power VCCQ and VCC by the 3.3V power
rail. Optional the user can connect the VCCQ to the pmic 1.8V emmc
power rail using a solder jumper.

Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval

commit 46b7edf1c7b7c91004c4db2c355cbd033f2385f9 upstream.

I've noticed that when writing data to the modem the writes can time out
at some point eventually. Looks like kicking the modem idle GPIO every
600 ms instead of once a second fixes the issue. Note that this rate is
different from our runtime PM autosuspend rate MDM6600_MODEM_IDLE_DELAY_MS
that we still want to keep at 1 second, so let's add a separate define for
PHY_MDM6600_IDLE_KICK_MS.

Fixes: f7f50b2a7b05 ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling

commit be4e3c737eebd75815633f4b8fd766defaf0f1fc upstream.

We have an interrupt handler for the wake-up GPIO pin, but we're missing
the code to wake-up the system. This can cause timeouts receiving data
for the UART that shares the wake-up GPIO pin with the USB PHY.

All we need to do is just wake the system and kick the autosuspend
timeout to fix the issue.

Fixes: 5d1ebbda0318 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/sun4i: de2/de3: Remove unsupported VI layer formats

commit a4769905f0ae32cae4f096f646ab03b8b4794c74 upstream.

YUV444 and YVU444 are planar formats, but HW format RGB888 is packed.
This means that those two mappings were never correct. Remove them.

Fixes: 60a3dcf96aa8 ("drm/sun4i: Add DE2 definitions for YUV formats")
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224173901.174016-2-jernej.skrabec@siol.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/sun4i: Fix DE2 VI layer format support

commit 20896ef137340e9426cf322606f764452f5eb960 upstream.

DE2 VI layer doesn't support blending which means alpha channel is
ignored. Replace all formats with alpha with "don't care" (X) channel.

Fixes: 7480ba4d7571 ("drm/sun4i: Add support for DE2 VI planes")
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224173901.174016-4-jernej.skrabec@siol.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: dapm: Correct DAPM handling of active widgets during shutdown

commit 9b3193089e77d3b59b045146ff1c770dd899acb1 upstream.

commit c2caa4da46a4 ("ASoC: Fix widget powerdown on shutdown") added a
set of the power state during snd_soc_dapm_shutdown to ensure the
widgets powered off. However, when commit 39eb5fd13dff
("ASoC: dapm: Delay w->power update until the changes are written")
added the new_power member of the widget structure, to differentiate
between the current power state and the target power state, it did not
update the shutdown to use the new_power member.

As new_power has not updated it will be left in the state set by the
last DAPM sequence, ie. 1 for active widgets. So as the DAPM sequence
for the shutdown proceeds it will turn the widgets on (despite them
already being on) rather than turning them off.

Fixes: 39eb5fd13dff ("ASoC: dapm: Delay w->power update until the changes are written")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228153145.21013-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: pcm512x: Fix unbalanced regulator enable call in probe error path

commit ac0a68997935c4acb92eaae5ad8982e0bb432d56 upstream.

When we get a clock error during probe we have to call
regulator_bulk_disable before bailing out, otherwise we trigger
a warning in regulator_put.

Fix this by using "goto err" like in the error cases above.

Fixes: 5a3af1293194d ("ASoC: pcm512x: Add PCM512x driver")
Signed-off-by: Matthias Reichl <hias@horus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200220202956.29233-1-hias@horus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: pcm: Fix possible buffer overflow in dpcm state sysfs output

commit 6c89ffea60aa3b2a33ae7987de1e84bfb89e4c9e upstream.

dpcm_show_state() invokes multiple snprintf() calls to concatenate
formatted strings on the fixed size buffer. The usage of snprintf()
is supposed for avoiding the buffer overflow, but it doesn't work as
expected because snprintf() doesn't return the actual output size but
the size to be written.

Fix this bug by replacing all snprintf() calls with scnprintf()
calls.

Fixes: f86dcef87b77 ("ASoC: dpcm: Add debugFS support for DPCM")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200218111737.14193-4-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: imx-sdma: remove dma_slave_config direction usage and leave sdma_event_enable()

[ Upstream commit 107d06441b709d31ce592535086992799ee51e17 ]

dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed

ENBLn bit should be set before any dma request triggered, please
refer to the below information from i.mx6sololite RM. Otherwise,
spi/uart test will be fail because there is dma request from tx
fifo always before dmaengine_prep_slave_sg() in where ENBLn set
and violate the below rule.

https://www.nxp.com/docs/en/reference-manual/IMX6SLRM.pdf:

40.8.28 Channel Enable RAM (SDMAARM_CHNENBLn)
"It is thus essential for the Arm platform to program them before
any DMA request is triggered to the SDMA, otherwise an unpredictable
combination of channels may be started".

Signed-off-by: Robin Gong <yibin.gong@nxp.com>
[vkoul: sqashed patch from Robin into direction change]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: intel: skl: Fix possible buffer overflow in debug outputs

commit 549cd0ba04dcfe340c349cd983bd440480fae8ee upstream.

The debugfs output of intel skl driver writes strings with multiple
snprintf() calls with the fixed size. This was supposed to avoid the
buffer overflow but actually it still would, because snprintf()
returns the expected size to be output, not the actual output size.

Fix it by replacing snprintf() calls with scnprintf().

Fixes: d14700a01f91 ("ASoC: Intel: Skylake: Debugfs facility to dump module config")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200218111737.14193-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: intel: skl: Fix pin debug prints

commit 64bbacc5f08c01954890981c63de744df1f29a30 upstream.

skl_print_pins() loops over all given pins but it overwrites the text
at the very same position while increasing the returned length.
Fix this to show the all pin contents properly.

Fixes: d14700a01f91 ("ASoC: Intel: Skylake: Debugfs facility to dump module config")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200218111737.14193-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: topology: Fix memleak in soc_tplg_manifest_load()

commit 242c46c023610dbc0213fc8fb6b71eb836bc5d95 upstream.

In case of ABI version mismatch, _manifest needs to be freed as
it is just a copy of the original topology manifest. However, if
a driver manifest handler is defined, that would get executed and
the cleanup is never reached. Fix that by getting the return status
of manifest() instead of returning directly.

Fixes: 583958fa2e52 ("ASoC: topology: Make manifest backward compatible from ABI v4")
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Link: https://lore.kernel.org/r/20200207185325.22320-3-dragos_tarcatu@mentor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: topology: Fix memleak in soc_tplg_link_elems_load()

commit 2b2d5c4db732c027a14987cfccf767dac1b45170 upstream.

If soc_tplg_link_config() fails, _link needs to be freed in case of
topology ABI version mismatch. However the current code is returning
directly and ends up leaking memory in this case.
This patch fixes that.

Fixes: 593d9e52f9bb ("ASoC: topology: Add support to configure existing physical DAI links")
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Link: https://lore.kernel.org/r/20200207185325.22320-2-dragos_tarcatu@mentor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: bcm63xx-hsspi: Really keep pll clk enabled

commit 51bddd4501bc414b8b1e8f4d096b4a5304068169 upstream.

The purpose of commit 0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
was to keep the pll clk enabled through the lifetime of the device.

In order to do that, some 'clk_prepare_enable()'/'clk_disable_unprepare()'
calls have been added in the error handling path of the probe function, in
the remove function and in the suspend and resume functions.

However, a 'clk_disable_unprepare()' call has been unfortunately left in
the probe function. So the commit seems to be more or less a no-op.

Axe it now, so that the pll clk is left enabled through the lifetime of
the device, as described in the commit.

Fixes: 0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20200228213838.7124-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: ls1021a: Restore MDIO compatible to gianfar

commit 7155c44624d061692b4c13aa8343f119c67d4fc0 upstream.

The difference between "fsl,etsec2-mdio" and "gianfar" has to do with
the .get_tbipa function, which calculates the address of the TBIPA
register automatically, if not explicitly specified. [ see
drivers/net/ethernet/freescale/fsl_pq_mdio.c ]. On LS1021A, the TBIPA
register is at offset 0x30 within the port register block, which is what
the "gianfar" method of calculating addresses actually does.

Luckily, the bad "compatible" is inconsequential for ls1021a.dtsi,
because the TBIPA register is explicitly specified via the second "reg"
(<0x0 0x2d10030 0x0 0x4>), so the "get_tbipa" function is dead code.
Nonetheless it's good to restore it to its correct value.

Background discussion:
https://www.spinics.net/lists/stable/msg361156.html

Fixes: c7861adbe37f ("ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm writecache: verify watermark during resume

commit 41c526c5af46d4c4dab7f72c99000b7fac0b9702 upstream.

Verify the watermark upon resume - so that if the target is reloaded
with lower watermark, it will start the cleanup process immediately.

Fixes: 48debafe4f2f ("dm: add writecache target")
Cc: stable@vger.kernel.org # 4.18+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm: report suspended device during destroy

commit adc0daad366b62ca1bce3e2958a40b0b71a8b8b3 upstream.

The function dm_suspended returns true if the target is suspended.
However, when the target is being suspended during unload, it returns
false.

An example where this is a problem: the test "!dm_suspended(wc->ti)" in
writecache_writeback is not sufficient, because dm_suspended returns
zero while writecache_suspend is in progress. As is, without an
enhanced dm_suspended, simply switching from flush_workqueue to
drain_workqueue still emits warnings:
workqueue writecache-writeback: drain_workqueue() isn't complete after 10 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 100 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 200 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 300 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 400 tries

writecache_suspend calls flush_workqueue(wc->writeback_wq) - this function
flushes the current work. However, the workqueue may re-queue itself and
flush_workqueue doesn't wait for re-queued works to finish. Because of
this - the function writecache_writeback continues execution after the
device was suspended and then concurrently with writecache_dtr, causing
a crash in writecache_writeback.

We must use drain_workqueue - that waits until the work and all re-queued
works finish.

As a prereq for switching to drain_workqueue, this commit fixes
dm_suspended to return true after the presuspend hook and before the
postsuspend hook - just like during a normal suspend. It allows
simplifying the dm-integrity and dm-writecache targets so that they
don't have to maintain suspended flags on their own.

With this change use of drain_workqueue() can be used effectively. This
change was tested with the lvm2 testsuite and cryptsetup testsuite and
the are no regressions.

Fixes: 48debafe4f2f ("dm: add writecache target")
Cc: stable@vger.kernel.org # 4.18+
Reported-by: Corey Marthaler <cmarthal@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm cache: fix a crash due to incorrect work item cancelling

commit 7cdf6a0aae1cccf5167f3f04ecddcf648b78e289 upstream.

The crash can be reproduced by running the lvm2 testsuite test
lvconvert-thin-external-cache.sh for several minutes, e.g.:
while :; do make check T=shell/lvconvert-thin-external-cache.sh; done

The crash happens in this call chain:
do_waker -> policy_tick -> smq_tick -> end_hotspot_period -> clear_bitset
-> memset -> __memset -- which accesses an invalid pointer in the vmalloc
area.

The work entry on the workqueue is executed even after the bitmap was
freed. The problem is that cancel_delayed_work doesn't wait for the
running work item to finish, so the work item can continue running and
re-submitting itself even after cache_postsuspend. In order to make sure
that the work item won't be running, we must use cancel_delayed_work_sync.

Also, change flush_workqueue to drain_workqueue, so that if some work item
submits itself or another work item, we are properly waiting for both of
them.

Fixes: c6b4fcbad044 ("dm: add cache target")
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: tegra-apb: Prevent race conditions of tasklet vs free list

commit c33ee1301c393a241d6424e36eff1071811b1064 upstream.

The interrupt handler puts a half-completed DMA descriptor on a free list
and then schedules tasklet to process bottom half of the descriptor that
executes client's callback, this creates possibility to pick up the busy
descriptor from the free list. Thus, let's disallow descriptor's re-use
until it is fully processed.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200209163356.6439-3-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: tegra-apb: Fix use-after-free

commit 94788af4ed039476ff3527b0e6a12c1dc42cb022 upstream.

I was doing some experiments with I2C and noticed that Tegra APB DMA
driver crashes sometime after I2C DMA transfer termination. The crash
happens because tegra_dma_terminate_all() bails out immediately if pending
list is empty, and thus, it doesn't release the half-completed descriptors
which are getting re-used before ISR tasklet kicks-in.

tegra-i2c 7000c400.i2c: DMA transfer timeout
elants_i2c 0-0010: elants_i2c_irq: failed to read data: -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 142 at lib/list_debug.c:45 __list_del_entry_valid+0x45/0xac
list_del corruption, ddbaac44->next is LIST_POISON1 (00000100)
Modules linked in:
CPU: 0 PID: 142 Comm: kworker/0:2 Not tainted 5.5.0-rc2-next-20191220-00175-gc3605715758d-dirty #538
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: events_freezable_power_ thermal_zone_device_check
[<c010e5c5>] (unwind_backtrace) from [<c010a1c5>] (show_stack+0x11/0x14)
[<c010a1c5>] (show_stack) from [<c0973925>] (dump_stack+0x85/0x94)
[<c0973925>] (dump_stack) from [<c011f529>] (__warn+0xc1/0xc4)
[<c011f529>] (__warn) from [<c011f7e9>] (warn_slowpath_fmt+0x61/0x78)
[<c011f7e9>] (warn_slowpath_fmt) from [<c042497d>] (__list_del_entry_valid+0x45/0xac)
[<c042497d>] (__list_del_entry_valid) from [<c047a87f>] (tegra_dma_tasklet+0x5b/0x154)
[<c047a87f>] (tegra_dma_tasklet) from [<c0124799>] (tasklet_action_common.constprop.0+0x41/0x7c)
[<c0124799>] (tasklet_action_common.constprop.0) from [<c01022ab>] (__do_softirq+0xd3/0x2a8)
[<c01022ab>] (__do_softirq) from [<c0124683>] (irq_exit+0x7b/0x98)
[<c0124683>] (irq_exit) from [<c0168c19>] (__handle_domain_irq+0x45/0x80)
[<c0168c19>] (__handle_domain_irq) from [<c043e429>] (gic_handle_irq+0x45/0x7c)
[<c043e429>] (gic_handle_irq) from [<c0101aa5>] (__irq_svc+0x65/0x94)
Exception stack(0xde2ebb90 to 0xde2ebbd8)

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200209163356.6439-2-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/pkeys: Manually set X86_FEATURE_OSPKE to preserve existing changes

commit 735a6dd02222d8d070c7bb748f25895239ca8c92 upstream.

Explicitly set X86_FEATURE_OSPKE via set_cpu_cap() instead of calling
get_cpu_cap() to pull the feature bit from CPUID after enabling CR4.PKE.
Invoking get_cpu_cap() effectively wipes out any {set,clear}_cpu_cap()
changes that were made between this_cpu->c_init() and setup_pku(), as
all non-synthetic feature words are reinitialized from the CPU's CPUID
values.

Blasting away capability updates manifests most visibility when running
on a VMX capable CPU, but with VMX disabled by BIOS. To indicate that
VMX is disabled, init_ia32_feat_ctl() clears X86_FEATURE_VMX, using
clear_cpu_cap() instead of setup_clear_cpu_cap() so that KVM can report
which CPU is misconfigured (KVM needs to probe every CPU anyways).
Restoring X86_FEATURE_VMX from CPUID causes KVM to think VMX is enabled,
ultimately leading to an unexpected #GP when KVM attempts to do VMXON.

Arguably, init_ia32_feat_ctl() should use setup_clear_cpu_cap() and let
KVM figure out a different way to report the misconfigured CPU, but VMX
is not the only feature bit that is affected, i.e. there is precedent
that tweaking feature bits via {set,clear}_cpu_cap() after ->c_init()
is expected to work. Most notably, x86_init_rdrand()'s clearing of
X86_FEATURE_RDRAND when RDRAND malfunctions is also overwritten.

Fixes: 0697694564c8 ("x86/mm/pkeys: Actually enable Memory Protection Keys in the CPU")
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200226231615.13664-1-sean.j.christopherson@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: v4l2-mem2mem.c: fix broken links

commit 316e730f1d8bb029fe6cec2468fb2a50424485b3 upstream.

The topology that v4l2_m2m_register_media_controller() creates for a
processing block actually created a source-to-source link and a sink-to-sink
link instead of two source-to-sink links.

Unfortunately v4l2-compliance never checked for such bad links, so this
went unreported for quite some time.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Nicolas Dufresne <nicolas@ndufresne.ca>
Cc: <stable@vger.kernel.org> # for v4.19 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt: selection, push sel_lock up

commit e8c75a30a23c6ba63f4ef6895cbf41fd42f21aa2 upstream.

sel_lock cannot nest in the console lock. Thanks to syzkaller, the
kernel states firmly:

> WARNING: possible circular locking dependency detected
> 5.6.0-rc3-syzkaller #0 Not tainted
> ------------------------------------------------------
> syz-executor.4/20336 is trying to acquire lock:
> ffff8880a2e952a0 (&tty->termios_rwsem){++++}, at: tty_unthrottle+0x22/0x100 drivers/tty/tty_ioctl.c:136
>
> but task is already holding lock:
> ffffffff89462e70 (sel_lock){+.+.}, at: paste_selection+0x118/0x470 drivers/tty/vt/selection.c:374
>
> which lock already depends on the new lock.
>
> the existing dependency chain (in reverse order) is:
>
> -> #2 (sel_lock){+.+.}:
>        mutex_lock_nested+0x1b/0x30 kernel/locking/mutex.c:1118
>        set_selection_kernel+0x3b8/0x18a0 drivers/tty/vt/selection.c:217
>        set_selection_user+0x63/0x80 drivers/tty/vt/selection.c:181
>        tioclinux+0x103/0x530 drivers/tty/vt/vt.c:3050
>        vt_ioctl+0x3f1/0x3a30 drivers/tty/vt/vt_ioctl.c:364

This is ioctl(TIOCL_SETSEL).
Locks held on the path: console_lock -> sel_lock

> -> #1 (console_lock){+.+.}:
>        console_lock+0x46/0x70 kernel/printk/printk.c:2289
>        con_flush_chars+0x50/0x650 drivers/tty/vt/vt.c:3223
>        n_tty_write+0xeae/0x1200 drivers/tty/n_tty.c:2350
>        do_tty_write drivers/tty/tty_io.c:962 [inline]
>        tty_write+0x5a1/0x950 drivers/tty/tty_io.c:1046

This is write().
Locks held on the path: termios_rwsem -> console_lock

> -> #0 (&tty->termios_rwsem){++++}:
>        down_write+0x57/0x140 kernel/locking/rwsem.c:1534
>        tty_unthrottle+0x22/0x100 drivers/tty/tty_ioctl.c:136
>        mkiss_receive_buf+0x12aa/0x1340 drivers/net/hamradio/mkiss.c:902
>        tty_ldisc_receive_buf+0x12f/0x170 drivers/tty/tty_buffer.c:465
>        paste_selection+0x346/0x470 drivers/tty/vt/selection.c:389
>        tioclinux+0x121/0x530 drivers/tty/vt/vt.c:3055
>        vt_ioctl+0x3f1/0x3a30 drivers/tty/vt/vt_ioctl.c:364

This is ioctl(TIOCL_PASTESEL).
Locks held on the path: sel_lock -> termios_rwsem

> other info that might help us debug this:
>
> Chain exists of:
>   &tty->termios_rwsem --> console_lock --> sel_lock

Clearly. From the above, we have:
console_lock -> sel_lock
sel_lock -> termios_rwsem
termios_rwsem -> console_lock

Fix this by reversing the console_lock -> sel_lock dependency in
ioctl(TIOCL_SETSEL). First, lock sel_lock, then console_lock.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+26183d9746e62da329b8@syzkaller.appspotmail.com
Fixes: 07e6124a1a46 ("vt: selection, close sel_buffer race")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200228115406.5735-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt: selection, push console lock down

commit 4b70dd57a15d2f4685ac6e38056bad93e81e982f upstream.

We need to nest the console lock in sel_lock, so we have to push it down
a bit. Fortunately, the callers of set_selection_* just lock the console
lock around the function call. So moving it down is easy.

In the next patch, we switch the order.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 07e6124a1a46 ("vt: selection, close sel_buffer race")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200228115406.5735-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt: selection, close sel_buffer race

commit 07e6124a1a46b4b5a9b3cacc0c306b50da87abf5 upstream.

syzkaller reported this UAF:
BUG: KASAN: use-after-free in n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741
Read of size 1 at addr ffff8880089e40e9 by task syz-executor.1/13184

CPU: 0 PID: 13184 Comm: syz-executor.1 Not tainted 5.4.7 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
...
kasan_report+0xe/0x20 mm/kasan/common.c:634
n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741
tty_ldisc_receive_buf+0xac/0x190 drivers/tty/tty_buffer.c:461
paste_selection+0x297/0x400 drivers/tty/vt/selection.c:372
tioclinux+0x20d/0x4e0 drivers/tty/vt/vt.c:3044
vt_ioctl+0x1bcf/0x28d0 drivers/tty/vt/vt_ioctl.c:364
tty_ioctl+0x525/0x15a0 drivers/tty/tty_io.c:2657
vfs_ioctl fs/ioctl.c:47 [inline]

It is due to a race between parallel paste_selection (TIOCL_PASTESEL)
and set_selection_user (TIOCL_SETSEL) invocations. One uses sel_buffer,
while the other frees it and reallocates a new one for another
selection. Add a mutex to close this race.

The mutex takes care properly of sel_buffer and sel_buffer_lth only. The
other selection global variables (like sel_start, sel_end, and sel_cons)
are protected only in set_selection_user. The other functions need quite
some more work to close the races of the variables there. This is going
to happen later.

This likely fixes (I am unsure as there is no reproducer provided) bug
206361 too. It was marked as CVE-2020-8648.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+59997e8d5cbdc486e6f6@syzkaller.appspotmail.com
References: https://bugzilla.kernel.org/show_bug.cgi?id=206361
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210081131.23572-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_exar: add support for ACCES cards

commit 10c5ccc3c6d32f3d7d6c07de1d3f0f4b52f3e3ab upstream.

Add ACCES VIDs and PIDs that use the Exar chips

Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200305140504.22237-1-jay.dolan@accesio.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty:serial:mvebu-uart:fix a wrong return

commit 4a3e208474204e879d22a310b244cb2f39e5b1f8 upstream.

in this place, the function should return a
negative value and the PTR_ERR already returns
a negative,so return -PTR_ERR() is wrong.

Signed-off-by: tangbin <tangbin@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200305013823.20976-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm: dts: dra76x: Fix mmc3 max-frequency

commit fa63c0039787b8fbacf4d6a51e3ff44288f5b90b upstream.

dra76x is not affected by i887 which requires mmc3 node to be limited to
a max frequency of 64 MHz. Fix this by overwriting the correct value in
the the dra76 specific dtsi.

Fixes: 895bd4b3e5ec ("ARM: dts: Add support for dra76-evm")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fat: fix uninit-memory access for partial initialized inode

commit bc87302a093f0eab45cd4e250c2021299f712ec6 upstream.

When get an error in the middle of reading an inode, some fields in the
inode might be still not initialized. And then the evict_inode path may
access those fields via iput().

To fix, this makes sure that inode fields are initialized.

Reported-by: syzbot+9d82b8de2992579da5d0@syzkaller.appspotmail.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/871rqnreqx.fsf@mail.parknet.co.jp
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: fix possible PMD dirty bit lost in set_pmd_migration_entry()

commit 8a8683ad9ba48b4b52a57f013513d1635c1ca5c4 upstream.

In set_pmd_migration_entry(), pmdp_invalidate() is used to change PMD
atomically.  But the PMD is read before that with an ordinary memory
reading.  If the THP (transparent huge page) is written between the PMD
reading and pmdp_invalidate(), the PMD dirty bit may be lost, and cause
data corruption.  The race window is quite small, but still possible in
theory, so need to be fixed.

The race is fixed via using the return value of pmdp_invalidate() to get
the original content of PMD, which is a read/modify/write atomic
operation.  So no THP writing can occur in between.

The race has been introduced when the THP migration support is added in
the commit 616b8371539a ("mm: thp: enable thp migration in generic path").
But this fix depends on the commit d52605d7cb30 ("mm: do not lose dirty
and accessed bits in pmdp_invalidate()").  So it's easy to be backported
after v4.16.  But the race window is really small, so it may be fine not
to backport the fix at all.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Link: http://lkml.kernel.org/r/20200220075220.2327056-1-ying.huang@intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, numa: fix bad pmd by atomically check for pmd_trans_huge when marking page tables prot_numa

commit 8b272b3cbbb50a6a8e62d8a15affd473a788e184 upstream.

: A user reported a bug against a distribution kernel while running a
: proprietary workload described as "memory intensive that is not swapping"
: that is expected to apply to mainline kernels.  The workload is
: read/write/modifying ranges of memory and checking the contents.  They
: reported that within a few hours that a bad PMD would be reported followed
: by a memory corruption where expected data was all zeros.  A partial
: report of the bad PMD looked like
:
:   [ 5195.338482] ../mm/pgtable-generic.c:33: bad pmd ffff8888157ba008(000002e0396009e2)
:   [ 5195.341184] ------------[ cut here ]------------
:   [ 5195.356880] kernel BUG at ../mm/pgtable-generic.c:35!
:   ....
:   [ 5195.410033] Call Trace:
:   [ 5195.410471]  [<ffffffff811bc75d>] change_protection_range+0x7dd/0x930
:   [ 5195.410716]  [<ffffffff811d4be8>] change_prot_numa+0x18/0x30
:   [ 5195.410918]  [<ffffffff810adefe>] task_numa_work+0x1fe/0x310
:   [ 5195.411200]  [<ffffffff81098322>] task_work_run+0x72/0x90
:   [ 5195.411246]  [<ffffffff81077139>] exit_to_usermode_loop+0x91/0xc2
:   [ 5195.411494]  [<ffffffff81003a51>] prepare_exit_to_usermode+0x31/0x40
:   [ 5195.411739]  [<ffffffff815e56af>] retint_user+0x8/0x10
:
: Decoding revealed that the PMD was a valid prot_numa PMD and the bad PMD
: was a false detection.  The bug does not trigger if automatic NUMA
: balancing or transparent huge pages is disabled.
:
: The bug is due a race in change_pmd_range between a pmd_trans_huge and
: pmd_nond_or_clear_bad check without any locks held.  During the
: pmd_trans_huge check, a parallel protection update under lock can have
: cleared the PMD and filled it with a prot_numa entry between the transhuge
: check and the pmd_none_or_clear_bad check.
:
: While this could be fixed with heavy locking, it's only necessary to make
: a copy of the PMD on the stack during change_pmd_range and avoid races.  A
: new helper is created for this as the check if quite subtle and the
: existing similar helpful is not suitable.  This passed 154 hours of
: testing (usually triggers between 20 minutes and 24 hours) without
: detecting bad PMDs or corruption.  A basic test of an autonuma-intensive
: workload showed no significant change in behaviour.

Although Mel withdrew the patch on the face of LKML comment
https://lkml.org/lkml/2017/4/10/922 the race window aforementioned is
still open, and we have reports of Linpack test reporting bad residuals
after the bad PMD warning is observed.  In addition to that, bad
rss-counter and non-zero pgtables assertions are triggered on mm teardown
for the task hitting the bad PMD.

host kernel: mm/pgtable-generic.c:40: bad pmd 00000000b3152f68(8000000d2d2008e7)
....
host kernel: BUG: Bad rss-counter state mm:00000000b583043d idx:1 val:512
host kernel: BUG: non-zero pgtables_bytes on freeing mm: 4096

The issue is observed on a v4.18-based distribution kernel, but the race
window is expected to be applicable to mainline kernels, as well.

[akpm@linux-foundation.org: fix comment typo, per Rafael]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Link: http://lkml.kernel.org/r/20200216191800.22423-1-aquini@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vgacon: Fix a UAF in vgacon_invert_region

commit 513dc792d6060d5ef572e43852683097a8420f56 upstream.

When syzkaller tests, there is a UAF:
  BUG: KASan: use after free in vgacon_invert_region+0x9d/0x110 at addr
    ffff880000100000
  Read of size 2 by task syz-executor.1/16489
  page:ffffea0000004000 count:0 mapcount:-127 mapping:          (null)
  index:0x0
  page flags: 0xfffff00000000()
  page dumped because: kasan: bad access detected
  CPU: 1 PID: 16489 Comm: syz-executor.1 Not tainted
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
  rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
  Call Trace:
    [<ffffffffb119f309>] dump_stack+0x1e/0x20
    [<ffffffffb04af957>] kasan_report+0x577/0x950
    [<ffffffffb04ae652>] __asan_load2+0x62/0x80
    [<ffffffffb090f26d>] vgacon_invert_region+0x9d/0x110
    [<ffffffffb0a39d95>] invert_screen+0xe5/0x470
    [<ffffffffb0a21dcb>] set_selection+0x44b/0x12f0
    [<ffffffffb0a3bfae>] tioclinux+0xee/0x490
    [<ffffffffb0a1d114>] vt_ioctl+0xff4/0x2670
    [<ffffffffb0a0089a>] tty_ioctl+0x46a/0x1a10
    [<ffffffffb052db3d>] do_vfs_ioctl+0x5bd/0xc40
    [<ffffffffb052e2f2>] SyS_ioctl+0x132/0x170
    [<ffffffffb11c9b1b>] system_call_fastpath+0x22/0x27
    Memory state around the buggy address:
     ffff8800000fff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
     00 00
     ffff8800000fff80: 00 00 00 00 00 00 00 00 00 00 00 00 00
     00 00 00
    >ffff880000100000: ff ff ff ff ff ff ff ff ff ff ff ff ff
     ff ff ff

It can be reproduce in the linux mainline by the program:
  #include <stdio.h>
  #include <stdlib.h>
  #include <unistd.h>
  #include <fcntl.h>
  #include <sys/types.h>
  #include <sys/stat.h>
  #include <sys/ioctl.h>
  #include <linux/vt.h>

  struct tiocl_selection {
    unsigned short xs;      /* X start */
    unsigned short ys;      /* Y start */
    unsigned short xe;      /* X end */
    unsigned short ye;      /* Y end */
    unsigned short sel_mode; /* selection mode */
  };

  #define TIOCL_SETSEL    2
  struct tiocl {
    unsigned char type;
    unsigned char pad;
    struct tiocl_selection sel;
  };

  int main()
  {
    int fd = 0;
    const char *dev = "/dev/char/4:1";

    struct vt_consize v = {0};
    struct tiocl tioc = {0};

    fd = open(dev, O_RDWR, 0);

    v.v_rows = 3346;
    ioctl(fd, VT_RESIZEX, &v);

    tioc.type = TIOCL_SETSEL;
    ioctl(fd, TIOCLINUX, &tioc);

    return 0;
  }

When resize the screen, update the 'vc->vc_size_row' to the new_row_size,
but when 'set_origin' in 'vgacon_set_origin', vgacon use 'vga_vram_base'
for 'vc_origin' and 'vc_visible_origin', not 'vc_screenbuf'. It maybe
smaller than 'vc_screenbuf'. When TIOCLINUX, use the new_row_size to calc
the offset, it maybe larger than the vga_vram_size in vgacon driver, then
bad access.
Also, if set an larger screenbuf firstly, then set an more larger
screenbuf, when copy old_origin to new_origin, a bad access may happen.

So, If the screen size larger than vga_vram, resize screen should be
failed. This alse fix CVE-2020-8649 and CVE-2020-8647.

Linus pointed out that overflow checking seems absent. We're saved by
the existing bounds checks in vc_do_resize() with rather strict
limits:

if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW)
return -EINVAL;

Fixes: 0aec4867dca14 ("[PATCH] SVGATextMode fix")
Reference: CVE-2020-8647 and CVE-2020-8649
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
[danvet: augment commit message to point out overflow safety]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304022429.37738-1-zhangxiaoxu5@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: port: do error out if usb_autopm_get_interface() fails

commit 1f8b39bc99a31759e97a0428a5c3f64802c1e61d upstream.

Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:

On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.

Factor out the usb_port_runtime_{resume,suspend}() changes into a
standalone patch to allow conflict-free porting on top of stable v3.9+.

[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org

Fixes: 971fcd492cebf5 ("usb: add runtime pm support for usb port device")
Cc: stable@vger.kernel.org # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: hub: do error out if usb_autopm_get_interface() fails

commit 60e3f6e4ac5b0fda43dad01c32e09409ec710045 upstream.

Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:

On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.

Factor out the usb_remove_device() change into a standalone patch to
allow conflict-free integration on top of the earliest stable branches.

[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org

Fixes: 253e05724f9230 ("USB: add a "remove hardware" sysfs attribute")
Cc: stable@vger.kernel.org # v2.6.33+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: core: hub: fix unhandled return by employing a void function

commit 63d6d7ed475c53dc1cabdfedf63de1fd8dcd72ee upstream.

Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):

usb: dwc3: gadget: Update chain bit correctly when using sg list

commit dad2aff3e827b112f27fa5e6f2bf87a110067c3f upstream.

If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.

At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.

Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: quirks: add NO_LPM quirk for Logitech Screen Share

commit b96ed52d781a2026d0c0daa5787c6f3d45415862 upstream.

LPM on the device appears to cause xHCI host controllers to claim
that there isn't enough bandwidth to support additional devices.

Signed-off-by: Dan Lazewatsky <dlaz@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: storage: Add quirk for Samsung Fit flash

commit 86d92f5465958752481269348d474414dccb1552 upstream.

Current driver has 240 (USB2.0) and 2048 (USB3.0) as max_sectors,
e.g., /sys/bus/scsi/devices/0:0:0:0/max_sectors

If data access times out, driver error handling will issue a port
reset.
Sometimes Samsung Fit (090C:1000) flash disk will not respond to
later Set Address or Get Descriptor command.

Adding this quirk to limit max_sectors to 64 sectors to avoid issue
occurring.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1583158895-31342-1-git-send-email-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: don't leak -EAGAIN for stat() during reconnect

commit fc513fac56e1b626ae48a74d7551d9c35c50129e upstream.

If from cifs_revalidate_dentry_attr() the SMB2/QUERY_INFO call fails with an
error, such as STATUS_SESSION_EXPIRED, causing the session to be reconnected
it is possible we will leak -EAGAIN back to the application even for
system calls such as stat() where this is not a valid error.

Fix this by re-trying the operation from within cifs_revalidate_dentry_attr()
if cifs_get_inode_info*() returns -EAGAIN.

This fixes stat() and possibly also other system calls that uses
cifs_revalidate_dentry*().

Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Fix silent output on Gigabyte X570 Aorus Master

commit 0d45e86d2267d5bdf7bbb631499788da1c27ceb2 upstream.

The Gigabyte X570 Aorus Master motherboard with ALC1220 codec
requires a similar workaround for Clevo laptops to enforce the
DAC/mixer connection path. Set up a quirk entry for that.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205275
Signed-off-by: Christian Lachner <gladiac@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200223092416.15016-2-gladiac@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Add Headset Mic supported

commit 78def224f59c05d00e815be946ec229719ccf377 upstream.

Dell desktop platform supported headset Mic.
Add pin verb to enable headset Mic.
This platform only support fixed type headset for Iphone type.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/b9da28d772ef43088791b0f3675929e7@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: thunderx: workaround BGX TX Underflow issue

[ Upstream commit 971617c3b761c876d686a2188220a33898c90e99 ]

While it is not yet understood why a TX underflow can easily occur
for SGMII interfaces resulting in a TX wedge. It has been found that
disabling/re-enabling the LMAC resolves the issue.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/xen: Distribute switch variables for initialization

[ Upstream commit 9038ec99ceb94fb8d93ade5e236b2928f0792c7c ]

Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.

To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.

arch/x86/xen/enlighten_pv.c: In function ‘xen_write_msr_safe’:
arch/x86/xen/enlighten_pv.c:904:12: warning: statement will never be executed [-Wswitch-unreachable]
904 | unsigned which;
| ^~~~~

[1] https://bugs.llvm.org/show_bug.cgi?id=44916

Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200220062318.69299-1-keescook@chromium.org
Reviewed-by: Juergen Gross <jgross@suse.com>
[boris: made @which an 'unsigned int']
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: Don't tell the OS that link is going down

[ Upstream commit 8a55c08d3bbc9ffc9639f69f742e59ebd99f913b ]

Remove code that tell the OS that link is going down when user
change flow control via ethtool. When link is up it isn't certain
that link goes down after 0x0605 aq command. If link doesn't go
down, OS thinks that link is down, but physical link is up. To
reset this state user have to take interface down and up.

If link goes down after 0x0605 command, FW send information
about that and after that driver tells the OS that the link goes
down. So this code in ethtool is unnecessary.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme: Fix uninitialized-variable warning

[ Upstream commit 15755854d53b4bbb0bb37a0fce66f0156cfc8a17 ]

gcc may detect a false positive on nvme using an unintialized variable
if setting features fails. Since this is not a fast path, explicitly
initialize this variable to suppress the warning.

Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/qdio: fill SL with absolute addresses

[ Upstream commit e9091ffd6a0aaced111b5d6ead5eaab5cd7101bc ]

As the comment says, sl->sbal holds an absolute address. qeth currently
solves this through wild casting, while zfcp doesn't care.

Handle this properly in the code that actually builds the SL.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com> [for qdio]
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/boot/compressed: Don't declare __force_order in kaslr_64.c

[ Upstream commit df6d4f9db79c1a5d6f48b59db35ccd1e9ff9adfc ]

GCC 10 changed the default to -fno-common, which leads to

    LD      arch/x86/boot/compressed/vmlinux
  ld: arch/x86/boot/compressed/pgtable_64.o:(.bss+0x0): multiple definition of `__force_order'; \
    arch/x86/boot/compressed/kaslr_64.o:(.bss+0x0): first defined here
  make[2]: *** [arch/x86/boot/compressed/Makefile:119: arch/x86/boot/compressed/vmlinux] Error 1

Since __force_order is already provided in pgtable_64.c, there is no
need to declare __force_order in kaslr_64.c.

Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200124181811.4780-1-hjl.tools@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390: make 'install' not depend on vmlinux

[ Upstream commit 94e90f727f7424d827256023cace829cad6896f4 ]

For the same reason as commit 19514fc665ff ("arm, kbuild: make "make
install" not depend on vmlinux"), the install targets should never
trigger the rebuild of the kernel.

The variable, CONFIGURE, is not set by anyone. Remove it as well.

Link: https://lkml.kernel.org/r/20200216144829.27023-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/cio: cio_ignore_proc_seq_next should increase position index

[ Upstream commit 8b101a5e14f2161869636ff9cb4907b7749dc0c2 ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Link: https://lore.kernel.org/r/d44c53a7-9bc1-15c7-6d4a-0c10cb9dffce@virtuozzo.com
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

watchdog: da9062: do not ping the hw during stop()

[ Upstream commit e9a0e65eda3f78d0b04ec6136c591c000cbc3b76 ]

The da9062 hw has a minimum ping cool down phase of at least 200ms. The
driver takes that into account by setting the min_hw_heartbeat_ms to
300ms and the core guarantees that the hw limit is observed for the
ping() calls. But the core can't guarantee the required minimum ping
cool down phase if a stop() command is send immediately after the ping()
command. So it is not allowed to ping the watchdog within the stop()
command as the driver does. Remove the ping can be done without doubts
because the watchdog gets disabled anyway and a (re)start resets the
watchdog counter too.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200120091729.16256-1-m.felsch@pengutronix.de
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ks8851-ml: Fix 16-bit IO operation

[ Upstream commit 58292104832fef6cb4a89f736012c0e0724c3442 ]

The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that
BE[3:0] signals are active high. This contradicts the measurements
of the behavior of the actual chip, where these signals behave as
active low. For example, to read the CIDER register, the bus must
expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ks8851-ml: Fix 16-bit data access

[ Upstream commit edacb098ea9c31589276152f09b4439052c0f2b1 ]

The packet data written to and read from Micrel KSZ8851-16MLLI must be
byte-swapped in 16-bit mode, add this byte-swapping.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ks8851-ml: Remove 8-bit bus accessors

[ Upstream commit 69233bba6543a37755158ca3382765387b8078df ]

This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown,
however the speculation is that this was some sort of attempt to support
the 8-bit bus mode.

As per the KS8851-16MLL documentation, all two registers accessed via the
8-bit accessors are internally 16-bit registers, so reading them using
16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read
outright, as it is already a concatenation of two 8-bit reads of that
register. The KS_RXQCR accesses are 8-bit only, however writing the top
8 bits of the register is OK as well, since the driver caches the entire
16-bit register value anyway.

Finally, the driver is not used by any hardware in the kernel right now.
The only hardware available to me is one with 16-bit bus, so I have no
way to test the 8-bit bus mode, however it is unlikely this ever really
worked anyway. If the 8-bit bus mode is ever required, it can be easily
added by adjusting the 16-bit accessors to do 2 consecutive accesses,
which is how this should have been done from the beginning.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: b53: Ensure the default VID is untagged

[ Upstream commit d965a5432d4c3e6b9c3d2bc1d4a800013bbf76f6 ]

We need to ensure that the default VID is untagged otherwise the switch
will be sending tagged frames and the results can be problematic. This
is especially true with b53 switches that use VID 0 as their default
VLAN since VID 0 has a special meaning.

Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID")
Fixes: 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: forwarding: use proto icmp for {gretap, ip6gretap}_mac testing

[ Upstream commit e8023b030ce1748930e2dc76353a262fe47d4745 ]

For tc ip_proto filter, when we extract the flow via __skb_flow_dissect()
without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to
the inner proto.

So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP
proto.

For test mirror_gre.sh, it may make user confused if we capture ICMP
message on $h3(since the flow is GRE message). So I move the capture
dev to h3-gt{4,6}, and only capture ICMP message.

Before the fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw)                            [ OK ]
TEST: egress mirror to gretap (skip_hw)                             [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw)                         [ OK ]
TEST: egress mirror to ip6gretap (skip_hw)                          [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw)              [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to gretap: envelope MAC (skip_hw)               [FAIL]
Expected to capture 10 packets, got 0.
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw)           [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw)            [FAIL]
Expected to capture 10 packets, got 0.
TEST: two simultaneously configured mirrors (skip_hw)               [ OK ]
WARN: Could not test offloaded functionality

After fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw)                            [ OK ]
TEST: egress mirror to gretap (skip_hw)                             [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw)                         [ OK ]
TEST: egress mirror to ip6gretap (skip_hw)                          [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw)              [ OK ]
TEST: egress mirror to gretap: envelope MAC (skip_hw)               [ OK ]
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw)           [ OK ]
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw)            [ OK ]
TEST: two simultaneously configured mirrors (skip_hw)               [ OK ]
WARN: Could not test offloaded functionality

Fixes: ba8d39871a10 ("selftests: forwarding: Add test for mirror to gretap")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <pmachata@gmail.com>
Tested-by: Petr Machata <pmachata@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dsi/pll: call vco set rate explicitly

[ Upstream commit c6659785dfb3f8d75f1fe637e4222ff8178f5280 ]

For a given byte clock, if VCO recalc value is exactly same as
vco set rate value, vco_set_rate does not get called assuming
VCO is already set to required value. But Due to GDSC toggle,
VCO values are erased in the HW. To make sure VCO is programmed
correctly, we forcefully call set_rate from vco_prepare.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dsi: save pll state before dsi host is powered off

[ Upstream commit a1028dcfd0dd97884072288d0c8ed7f30399b528 ]

Save pll state before dsi host is powered off. Without this change
some register values gets resetted.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: megaraid_sas: silence a warning

[ Upstream commit 0e99b2c625da181aebf1a3d13493e3f7a5057a9c ]

Add a flag to DMA memory allocation to silence a warning.

This driver allocates DMA memory for IO frames. This allocation may exceed
MAX_ORDER pages for few megaraid_sas controllers (controllers with very
high queue depth). Consequently, the driver has logic to keep reducing the
controller queue depth until the DMA memory allocation succeeds.

On impacted megaraid_sas controllers there would be multiple DMA allocation
failures until driver settled on an allocation that fit. These failed DMA
allocation requests caused stack traces in system logs. These were not
harmful and this patch silences those warnings/stack traces.

[mkp: clarified commit desc]

Link: https://lore.kernel.org/r/20200204152413.7107-1-thenzl@redhat.com
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm: msm: Fix return type of dsi_mgr_connector_mode_valid for kCFI

[ Upstream commit 7fd2dfc3694922eb7ace4801b7208cf9f62ebc7d ]

I was hitting kCFI crashes when building with clang, and after
some digging finally narrowed it down to the
dsi_mgr_connector_mode_valid() function being implemented as
returning an int, instead of an enum drm_mode_status.

This patch fixes it, and appeases the opaque word of the kCFI
gods (seriously, clang inlining everything makes the kCFI
backtraces only really rough estimates of where things went
wrong).

Thanks as always to Sami for his help narrowing this down.

Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: freedreno@lists.freedesktop.org
Cc: clang-built-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/mdp5: rate limit pp done timeout warnings

[ Upstream commit ef8c9809acb0805c991bba8bdd4749fc46d44a98 ]

Add rate limiting of the 'pp done time out' warnings since these
warnings can quickly fill the dmesg buffer.

Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: serial: fix Tx stall after buffer overflow

[ Upstream commit e4bfded56cf39b8d02733c1e6ef546b97961e18a ]

Symptom: application opens /dev/ttyGS0 and starts sending (writing) to
it while either USB cable is not connected, or nobody listens on the
other side of the cable. If driver circular buffer overflows before
connection is established, no data will be written to the USB layer
until/unless /dev/ttyGS0 is closed and re-opened again by the
application (the latter besides having no means of being notified about
the event of establishing of the connection.)

Fix: on open and/or connect, kick Tx to flush circular buffer data to
USB layer.

Signed-off-by: Sergey Organov <sorganov@gmail.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags

[ Upstream commit 43d565727a3a6fd24e37c7c2116475106af71806 ]

ffs_aio_cancel() can be called from both interrupt and thread context. Make
sure that the current IRQ state is saved and restored by using
spin_{un,}lock_irq{save,restore}().

Otherwise undefined behavior might occur.

Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: composite: Support more than 500mA MaxPower

[ Upstream commit a2035411fa1d1206cea7d5dfe833e78481844a76 ]

USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power
when in configured state. However, if a configuration wanting to
take advantage of this is added with MaxPower greater than 500
(currently possible if using a ConfigFS gadget) the composite
driver fails to accommodate this for a couple reasons:

- usb_gadget_vbus_draw() when called from set_config() and
   composite_resume() will be passed the MaxPower value without
   regard for the current connection speed, resulting in a
   violation for USB 2.0 since the max is 500mA.

- the bMaxPower of the configuration descriptor would be
   incorrectly encoded, again if the connection speed is only
   at USB 2.0 or below, likely wrapping around U8_MAX since
   the 2mA multiplier corresponds to a maximum of 510mA.

Fix these by adding checks against the current gadget->speed
when the c->MaxPower value is used (set_config() and
composite_resume()) and appropriately limit based on whether
it is currently at a low-/full-/high- or super-speed connection.

Because 900 is not divisible by 8, with the round-up division
currently used in encode_bMaxPower() a MaxPower of 900mA will
result in an encoded value of 0x71. When a host stack (including
Linux and Windows) enumerates this on a single port root hub, it
reads this value back and decodes (multiplies by 8) to get 904mA
which is strictly greater than 900mA that is typically budgeted
for that port, causing it to reject the configuration. Instead,
we should be using the round-down behavior of normal integral
division so that 900 / 8 -> 0x70 or 896mA to stay within range.
And we might as well change it for the high/full/low case as well
for consistency.

N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't
seem to be any any peripheral controller supported by Linux that
does two lane operation, so for now keeping the clamp at 900
should be fine.

Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: fix too long argument

[ Upstream commit c363eb48ada5cf732b3f489fab799fc881097842 ]

With some shells, the command construed for install of bpf selftests becomes
too large due to long list of files:

make[1]: execvp: /bin/sh: Argument list too long
make[1]: *** [../lib.mk:73: install] Error 127

Currently, each of the file lists is replicated three times in the command:
in the shell 'if' condition, in the 'echo' and in the 'rsync'. Reduce that
by one instance by using make conditionals and separate the echo and rsync
into two shell commands. (One would be inclined to just remove the '@' at
the beginning of the rsync command and let 'make' echo it by itself;
unfortunately, it appears that the '@' in the front of mkdir silences output
also for the following commands.)

Also, separate handling of each of the lists to its own shell command.

The semantics of the makefile is unchanged before and after the patch. The
ability of individual test directories to override INSTALL_RULE is retained.

Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Tested-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE

[ Upstream commit 87c5cbf71ecbb9e289d60a2df22eb686c70bf196 ]

On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.

Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda: do not override bus codec_mask in link_get()

[ Upstream commit 43bcb1c0507858cdc95e425017dcc33f8105df39 ]

snd_hdac_ext_bus_link_get() does not work correctly in case
there are multiple codecs on the bus. It unconditionally
resets the bus->codec_mask value. As per documentation in
hdaudio.h and existing use in client code, this field should
be used to store bit flag of detected codecs on the bus.

By overwriting value of the codec_mask, information on all
detected codecs is lost. No current user of hdac is impacted,
but use of bus->codec_mask is planned in future patches
for SOF.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200206200223.7715-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kprobes: Fix optimize_kprobe()/unoptimize_kprobe() cancellation logic

[ Upstream commit e4add247789e4ba5e08ad8256183ce2e211877d4 ]

optimize_kprobe() and unoptimize_kprobe() cancels if a given kprobe
is on the optimizing_list or unoptimizing_list already. However, since
the following commit:

  f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code")

modified the update timing of the KPROBE_FLAG_OPTIMIZED, it doesn't
work as expected anymore.

The optimized_kprobe could be in the following states:

- [optimizing]: Before inserting jump instruction
  op.kp->flags has KPROBE_FLAG_OPTIMIZED and
  op->list is not empty.

- [optimized]: jump inserted
  op.kp->flags has KPROBE_FLAG_OPTIMIZED and
  op->list is empty.

- [unoptimizing]: Before removing jump instruction (including unused
  optprobe)
  op.kp->flags has KPROBE_FLAG_OPTIMIZED and
  op->list is not empty.

- [unoptimized]: jump removed
  op.kp->flags doesn't have KPROBE_FLAG_OPTIMIZED and
  op->list is empty.

Current code mis-expects [unoptimizing] state doesn't have
KPROBE_FLAG_OPTIMIZED, and that can cause incorrect results.

To fix this, introduce optprobe_queued_unopt() to distinguish [optimizing]
and [unoptimizing] states and fixes the logic in optimize_kprobe() and
unoptimize_kprobe().

[ mingo: Cleaned up the changelog and the code a bit. ]

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bristot@redhat.com
Fixes: f66c0447cca1 ("kprobes: Set unoptimized flag after unoptimizing code")
Link: https://lkml.kernel.org/r/157840814418.7181.13478003006386303481.stgit@devnote2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/core: Fix use of logical OR in get_new_pps

[ Upstream commit 4ca501d6aaf21de31541deac35128bbea8427aa6 ]

Clang warns:

../drivers/infiniband/core/security.c:351:41: warning: converting the
enum constant to a boolean [-Wint-in-bool-context]
if (!(qp_attr_mask & (IB_QP_PKEY_INDEX || IB_QP_PORT)) && qp_pps) {
^
1 warning generated.

A bitwise OR should have been used instead.

Fixes: 1dd017882e01 ("RDMA/core: Fix protection fault in get_pkey_idx_qp_list")
Link: https://lore.kernel.org/r/20200217204318.13609-1-natechancellor@gmail.com
Link: https://github.com/ClangBuiltLinux/linux/issues/889
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/core: Fix pkey and port assignment in get_new_pps

[ Upstream commit 801b67f3eaafd3f2ec8b65d93142d4ffedba85df ]

When port is part of the modify mask, then we should take it from the
qp_attr and not from the old pps. Same for PKEY. Otherwise there are
panics in some configurations:

  RIP: 0010:get_pkey_idx_qp_list+0x50/0x80 [ib_core]
  Code: c7 18 e8 13 04 30 ef 0f b6 43 06 48 69 c0 b8 00 00 00 48 03 85 a0 04 00 00 48 8b 50 20 48 8d 48 20 48 39 ca 74 1a 0f b7 73 04 <66> 39 72 10 75 08 eb 10 66 39 72 10 74 0a 48 8b 12 48 39 ca 75 f2
  RSP: 0018:ffffafb3480932f0 EFLAGS: 00010203
  RAX: ffff98059ababa10 RBX: ffff980d926e8cc0 RCX: ffff98059ababa30
  RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff98059ababa28
  RBP: ffff98059b940000 R08: 00000000000310c0 R09: ffff97fe47c07480
  R10: 0000000000000036 R11: 0000000000000200 R12: 0000000000000071
  R13: ffff98059b940000 R14: ffff980d87f948a0 R15: 0000000000000000
  FS:  00007f88deb31740(0000) GS:ffff98059f600000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000010 CR3: 0000000853e26001 CR4: 00000000001606e0
  Call Trace:
   port_pkey_list_insert+0x3d/0x1b0 [ib_core]
   ? kmem_cache_alloc_trace+0x215/0x220
   ib_security_modify_qp+0x226/0x3a0 [ib_core]
   _ib_modify_qp+0xcf/0x390 [ib_core]
   ipoib_init_qp+0x7f/0x200 [ib_ipoib]
   ? rvt_modify_port+0xd0/0xd0 [rdmavt]
   ? ib_find_pkey+0x99/0xf0 [ib_core]
   ipoib_ib_dev_open_default+0x1a/0x200 [ib_ipoib]
   ipoib_ib_dev_open+0x96/0x130 [ib_ipoib]
   ipoib_open+0x44/0x130 [ib_ipoib]
   __dev_open+0xd1/0x160
   __dev_change_flags+0x1ab/0x1f0
   dev_change_flags+0x23/0x60
   do_setlink+0x328/0xe30
   ? __nla_validate_parse+0x54/0x900
   __rtnl_newlink+0x54e/0x810
   ? __alloc_pages_nodemask+0x17d/0x320
   ? page_fault+0x30/0x50
   ? _cond_resched+0x15/0x30
   ? kmem_cache_alloc_trace+0x1c8/0x220
   rtnl_newlink+0x43/0x60
   rtnetlink_rcv_msg+0x28f/0x350
   ? kmem_cache_alloc+0x1fb/0x200
   ? _cond_resched+0x15/0x30
   ? __kmalloc_node_track_caller+0x24d/0x2d0
   ? rtnl_calcit.isra.31+0x120/0x120
   netlink_rcv_skb+0xcb/0x100
   netlink_unicast+0x1e0/0x340
   netlink_sendmsg+0x317/0x480
   ? __check_object_size+0x48/0x1d0
   sock_sendmsg+0x65/0x80
   ____sys_sendmsg+0x223/0x260
   ? copy_msghdr_from_user+0xdc/0x140
   ___sys_sendmsg+0x7c/0xc0
   ? skb_dequeue+0x57/0x70
   ? __inode_wait_for_writeback+0x75/0xe0
   ? fsnotify_grab_connector+0x45/0x80
   ? __dentry_kill+0x12c/0x180
   __sys_sendmsg+0x58/0xa0
   do_syscall_64+0x5b/0x200
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  RIP: 0033:0x7f88de467f10

Link: https://lore.kernel.org/r/20200227125728.100551-1-leon@kernel.org
Cc: <stable@vger.kernel.org>
Fixes: 1dd017882e01 ("RDMA/core: Fix protection fault in get_pkey_idx_qp_list")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: bcm_sf2: Forcibly configure IMP port for 1Gb/sec

[ Upstream commit 98c5f7d44fef309e692c24c6d71131ee0f0871fb ]

We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.

Fixes: 8f1880cbe8d0 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Fixes: de34d7084edd ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek - Fix a regression for mute led on Lenovo Carbon X1

[ Upstream commit c37c0ab029569a75fd180edb03d411e7a28a936f ]

Need to chain the THINKPAD_ACPI, otherwise the mute led will not
work.

Fixes: d2cd795c4ece ("ALSA: hda - fixup for the bass speaker on Lenovo Carbon X1 7th gen")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200219052306.24935-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

EDAC/amd64: Set grain per DIMM

[ Upstream commit 466503d6b1b33be46ab87c6090f0ade6c6011cbc ]

The following commit introduced a warning on error reports without a
non-zero grain value.

3724ace582d9 ("EDAC/mc: Fix grain_bits calculation")

The amd64_edac_mod module does not provide a value, so the warning will
be given on the first reported memory error.

Set the grain per DIMM to cacheline size (64 bytes). This is the current
recommendation.

Fixes: 3724ace582d9 ("EDAC/mc: Fix grain_bits calculation")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Robert Richter <rrichter@marvell.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191022203448.13962-7-Yazen.Ghannam@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 4.19.108

audit: always check the netlink payload length in audit_receive_msg()

[ Upstream commit 756125289285f6e55a03861bf4b6257aa3d19a93 ]

This patch ensures that we always check the netlink payload length
in audit_receive_msg() before we take any action on the payload
itself.

Cc: stable@vger.kernel.org
Reported-by: syzbot+399c44bf1f43b8747403@syzkaller.appspotmail.com
Reported-by: syzbot+e4b12d8d202701f08b6d@syzkaller.appspotmail.com
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mm, thp: fix defrag setting if newline is not used

commit f42f25526502d851d0e3ca1e46297da8aafce8a7 upstream.

If thp defrag setting "defer" is used and a newline is *not* used when
writing to the sysfs file, this is interpreted as the "defer+madvise"
option.

This is because we do prefix matching and if five characters are written
without a newline, the current code ends up comparing to the first five
bytes of the "defer+madvise" option and using that instead.

Use the more appropriate sysfs_streq() that handles the trailing newline
for us.  Since this doubles as a nice cleanup, do it in enabled_store()
as well.

The current implementation relies on prefix matching: the number of
bytes compared is either the number of bytes written or the length of
the option being compared.  With a newline, "defer\n" does not match
"defer+"madvise"; without a newline, however, "defer" is considered to
match "defer+madvise" (prefix matching is only comparing the first five
bytes).  End result is that writing "defer" is broken unless it has an
additional trailing character.

This means that writing "madv" in the past would match and set
"madvise".  With strict checking, that no longer is the case but it is
unlikely anybody is currently doing this.

Link: http://lkml.kernel.org/r/alpine.DEB.2.21.2001171411020.56385@chino.kir.corp.google.com
Fixes: 21440d7eb904 ("mm, thp: add new defer+madvise defrag option")
Signed-off-by: David Rientjes <rientjes@google.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/huge_memory.c: use head to check huge zero page

commit cb829624867b5ab10bc6a7036d183b1b82bfe9f8 upstream.

The page could be a tail page, if this is the case, this BUG_ON will
never be triggered.

Link: http://lkml.kernel.org/r/20200110032610.26499-1-richardw.yang@linux.intel.com
Fixes: e9b61f19858a ("thp: reintroduce split_huge_page()")

Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nf_flowtable: fix documentation

commit 78e06cf430934fc3768c342cbebdd1013dcd6fa7 upstream.

In the flowtable documentation there is a missing semicolon, the command
as is would give this error:

    nftables.conf:5:27-33: Error: syntax error, unexpected devices, expecting newline or semicolon
                    hook ingress priority 0 devices = { br0, pppoe-data };
                                            ^^^^^^^
    nftables.conf:4:12-13: Error: invalid hook (null)
            flowtable ft {
                      ^^

Fixes: 19b351f16fd9 ("netfilter: add flowtable documentation")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nft_tunnel: no need to call htons() when dumping ports

commit cf3e204a1ca5442190018a317d9ec181b4639bd6 upstream.

info->key.tp_src and tp_dst are __be16, when using nla_put_be16()
to dump them, htons() is not needed, so remove it in this patch.

Fixes: af308b94a2a4 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thermal: brcmstb_thermal: Do not use DT coefficients

commit e1ff6fc22f19e2af8adbad618526b80067911d40 upstream.

At the time the brcmstb_thermal driver and its binding were merged, the
DT binding did not make the coefficients properties a mandatory one,
therefore all users of the brcmstb_thermal driver out there have a non
functional implementation with zero coefficients. Even if these
properties were provided, the formula used for computation is incorrect.

The coefficients are entirely process specific (right now, only 28nm is
supported) and not board or SoC specific, it is therefore appropriate to
hard code them in the driver given the compatibility string we are
probed with which has to be updated whenever a new process is
introduced.

We remove the existing coefficients definition since subsequent patches
are going to add support for a new process and will introduce new
coefficients as well.

Fixes: 9e03cf1b2dd5 ("thermal: add brcmstb AVS TMON driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200114190607.29339-2-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Remove spurious clearing of async #PF MSR

commit 208050dac5ef4de5cb83ffcafa78499c94d0b5ad upstream.

Remove a bogus clearing of apf.msr_val from kvm_arch_vcpu_destroy().

apf.msr_val is only set to a non-zero value by kvm_pv_enable_async_pf(),
which is only reachable by kvm_set_msr_common(), i.e. by writing
MSR_KVM_ASYNC_PF_EN.  KVM does not autonomously write said MSR, i.e.
can only be written via KVM_SET_MSRS or KVM_RUN.  Since KVM_SET_MSRS and
KVM_RUN are vcpu ioctls, they require a valid vcpu file descriptor.
kvm_arch_vcpu_destroy() is only called if KVM_CREATE_VCPU fails, and KVM
declares KVM_CREATE_VCPU successful once the vcpu fd is installed and
thus visible to userspace.  Ergo, apf.msr_val cannot be non-zero when
kvm_arch_vcpu_destroy() is called.

Fixes: 344d9588a9df0 ("KVM: Add PV MSR to enable asynchronous page faults delivery.")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Remove spurious kvm_mmu_unload() from vcpu destruction path

commit 9d979c7e6ff43ca3200ffcb74f57415fd633a2da upstream.

x86 does not load its MMU until KVM_RUN, which cannot be invoked until
after vCPU creation succeeds. Given that kvm_arch_vcpu_destroy() is
called if and only if vCPU creation fails, it is impossible for the MMU
to be loaded.

Note, the bogus kvm_mmu_unload() call was added during an unrelated
refactoring of vCPU allocation, i.e. was presumably added as an
opportunstic "fix" for a perceived leak.

Fixes: fb3f0f51d92d1 ("KVM: Dynamically allocate vcpus")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf hists browser: Restore ESC as "Zoom out" of DSO/thread/etc

commit 3f7774033e6820d25beee5cf7aefa11d4968b951 upstream.

We need to set actions->ms.map since 599a2f38a989 ("perf hists browser:
Check sort keys before hot key actions"), as in that patch we bail out
if map is NULL.

Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 599a2f38a989 ("perf hists browser: Check sort keys before hot key actions")
Link: https://lkml.kernel.org/n/tip-wp1ssoewy6zihwwexqpohv0j@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pwm: omap-dmtimer: put_device() after of_find_device_by_node()

commit c7cb3a1dd53f63c64fb2b567d0be130b92a44d91 upstream.

This was found by coccicheck:

drivers/pwm/pwm-omap-dmtimer.c:304:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 255, but without a corresponding
object release within this function.

Reported-by: Markus Elfring <elfring@users.sourceforge.net>
Fixes: 6604c6556db9 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kprobes: Set unoptimized flag after unoptimizing code

commit f66c0447cca1281116224d474cdb37d6a18e4b5b upstream.

Set the unoptimized flag after confirming the code is completely
unoptimized. Without this fix, when a kprobe hits the intermediate
modified instruction (the first byte is replaced by an INT3, but
later bytes can still be a jump address operand) while unoptimizing,
it can return to the middle byte of the modified code, which causes
an invalid instruction exception in the kernel.

Usually, this is a rare case, but if we put a probe on the function
call while text patching, it always causes a kernel panic as below:

# echo p text_poke+5 > kprobe_events
# echo 1 > events/kprobes/enable
# echo 0 > events/kprobes/enable

invalid opcode: 0000 [#1] PREEMPT SMP PTI
RIP: 0010:text_poke+0x9/0x50
Call Trace:
  arch_unoptimize_kprobe+0x22/0x28
  arch_unoptimize_kprobes+0x39/0x87
  kprobe_optimizer+0x6e/0x290
  process_one_work+0x2a0/0x610
  worker_thread+0x28/0x3d0
  ? process_one_work+0x610/0x610
  kthread+0x10d/0x130
  ? kthread_park+0x80/0x80
  ret_from_fork+0x3a/0x50

text_poke() is used for patching the code in optprobes.

This can happen even if we blacklist text_poke() and other functions,
because there is a small time window during which we show the intermediate
code to other CPUs.

[ mingo: Edited the changelog. ]

Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bristot@redhat.com
Fixes: 6274de4984a6 ("kprobes: Support delayed unoptimizing")
Link: https://lkml.kernel.org/r/157483422375.25881.13508326028469515760.stgit@devnote2
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: net: xgene: Fix the order of the arguments of 'alloc_etherdev_mqs()'

commit 5a44c71ccda60a50073c5d7fe3f694cdfa3ab0c2 upstream.

'alloc_etherdev_mqs()' expects first 'tx', then 'rx'. The semantic here
looks reversed.

Reorder the arguments passed to 'alloc_etherdev_mqs()' in order to keep
the correct semantic.

In fact, this is a no-op because both XGENE_NUM_[RT]X_RING are 8.

Fixes: 107dec2749fe ("drivers: net: xgene: Add support for multiple queues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf stat: Fix shadow stats for clock events

commit 57ddf09173c1e7d0511ead8924675c7198e56545 upstream.

Commit 0aa802a79469 ("perf stat: Get rid of extra clock display
function") introduced scale and unit for clock events. Thus,
perf_stat__update_shadow_stats() now saves scaled values of clock events
in msecs, instead of original nsecs. But while calculating values of
shadow stats we still consider clock event values in nsecs. This results
in a wrong shadow stat values. Ex,

  # ./perf stat -e task-clock,cycles ls
    <SNIP>
              2.60 msec task-clock:u    #    0.877 CPUs utilized
         2,430,564      cycles:u        # 1215282.000 GHz

Fix this by saving original nsec values for clock events in
perf_stat__update_shadow_stats(). After patch:

  # ./perf stat -e task-clock,cycles ls
    <SNIP>
              3.14 msec task-clock:u    #    0.839 CPUs utilized
         3,094,528      cycles:u        #    0.985 GHz

Suggested-by: Jiri Olsa <jolsa@redhat.com>
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: yuzhoujian@didichuxing.com
Fixes: 0aa802a79469 ("perf stat: Get rid of extra clock display function")
Link: http://lkml.kernel.org/r/20181116042843.24067-1-ravi.bangoria@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf stat: Use perf_evsel__is_clocki() for clock events

commit eb08d006054e7e374592068919e32579988602d4 upstream.

We already have function to check if a given event is either
SW_CPU_CLOCK or SW_TASK_CLOCK. Utilize it.

Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: yuzhoujian@didichuxing.com
Link: http://lkml.kernel.org/r/20181115095533.16930-1-ravi.bangoria@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/fair: Fix O(nr_cgroups) in the load balancing path

commit 039ae8bcf7a5f4476f4487e6bf816885fb3fb617 upstream.

This re-applies the commit reverted here:

commit c40f7d74c741 ("sched/fair: Fix infinite loop in update_blocked_averages() by reverting a9e7f6544b9c")

I.e. now that cfs_rq can be safely removed/added in the list, we can re-apply:

commit a9e7f6544b9c ("sched/fair: Fix O(nr_cgroups) in load balance path")

Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: sargun@sargun.me
Cc: tj@kernel.org
Cc: xiexiuqi@huawei.com
Cc: xiezhipeng1@huawei.com
Link: https://lkml.kernel.org/r/1549469662-13614-3-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Vishnu Rangayyan <vishnu.rangayyan@apple.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/fair: Optimize update_blocked_averages()

commit 31bc6aeaab1d1de8959b67edbed5c7a4b3cdbe7c upstream.

Removing a cfs_rq from rq->leaf_cfs_rq_list can break the parent/child
ordering of the list when it will be added back. In order to remove an
empty and fully decayed cfs_rq, we must remove its children too, so they
will be added back in the right order next time.

With a normal decay of PELT, a parent will be empty and fully decayed
if all children are empty and fully decayed too. In such a case, we just
have to ensure that the whole branch will be added when a new task is
enqueued. This is default behavior since :

commit f6783319737f ("sched/fair: Fix insertion in rq->leaf_cfs_rq_list")

In case of throttling, the PELT of throttled cfs_rq will not be updated
whereas the parent will. This breaks the assumption made above unless we
remove the children of a cfs_rq that is throttled. Then, they will be
added back when unthrottled and a sched_entity will be enqueued.

As throttled cfs_rq are now removed from the list, we can remove the
associated test in update_blocked_averages().

Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: sargun@sargun.me
Cc: tj@kernel.org
Cc: xiexiuqi@huawei.com
Cc: xiezhipeng1@huawei.com
Link: https://lkml.kernel.org/r/1549469662-13614-2-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Vishnu Rangayyan <vishnu.rangayyan@apple.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: Check for a bad hva before dropping into the ghc slow path

commit fcfbc617547fc6d9552cb6c1c563b6a90ee98085 upstream.

When reading/writing using the guest/host cache, check for a bad hva
before checking for a NULL memslot, which triggers the slow path for
handing cross-page accesses. Because the memslot is nullified on error
by __kvm_gfn_to_hva_cache_init(), if the bad hva is encountered after
crossing into a new page, then the kvm_{read,write}_guest() slow path
could potentially write/access the first chunk prior to detecting the
bad hva.

Arguably, performing a partial access is semantically correct from an
architectural perspective, but that behavior is certainly not intended.
In the original implementation, memslot was not explicitly nullified
and therefore the partial access behavior varied based on whether the
memslot itself was null, or if the hva was simply bad. The current
behavior was introduced as a seemingly unintentional side effect in
commit f1b9dd5eb86c ("kvm: Disallow wraparound in
kvm_gfn_to_hva_cache_init"), which justified the change with "since some
callers don't check the return code from this function, it sit seems
prudent to clear ghc->memslot in the event of an error".

Regardless of intent, the partial access is dependent on _not_ checking
the result of the cache initialization, which is arguably a bug in its
own right, at best simply weird.

Fixes: 8f964525a121 ("KVM: Allow cross page reads and writes from cached translations.")
Cc: Jim Mattson <jmattson@google.com>
Cc: Andrew Honig <ahonig@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: SVM: Override default MMIO mask if memory encryption is enabled

commit 52918ed5fcf05d97d257f4131e19479da18f5d16 upstream.

The KVM MMIO support uses bit 51 as the reserved bit to cause nested page
faults when a guest performs MMIO. The AMD memory encryption support uses
a CPUID function to define the encryption bit position. Given this, it is
possible that these bits can conflict.

Use svm_hardware_setup() to override the MMIO mask if memory encryption
support is enabled. Various checks are performed to ensure that the mask
is properly defined and rsvd_bits() is used to generate the new mask (as
was done prior to the change that necessitated this patch).

Fixes: 28a1f3ac1d0c ("kvm: x86: Set highest physical address bits in non-present/reserved SPTEs")
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: delete unused mwifiex_get_intf_num()

commit 1c9f329b084b7b8ea6d60d91a202e884cdcf6aae upstream.

Commit 7afb94da3cd8 ("mwifiex: update set_mac_address logic") fixed the
only user of this function, partly because the author seems to have
noticed that, as written, it's on the borderline between highly
misleading and buggy.

Anyway, no sense in keeping dead code around: let's drop it.

Fixes: 7afb94da3cd8 ("mwifiex: update set_mac_address logic")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: drop most magic numbers from mwifiex_process_tdls_action_frame()

commit 70e5b8f445fd27fde0c5583460e82539a7242424 upstream.

Before commit 1e58252e334d ("mwifiex: Fix heap overflow in
mmwifiex_process_tdls_action_frame()"),
mwifiex_process_tdls_action_frame() already had too many magic numbers.
But this commit just added a ton more, in the name of checking for
buffer overflows. That seems like a really bad idea.

Let's make these magic numbers a little less magic, by
(a) factoring out 'pos[1]' as 'ie_len'
(b) using 'sizeof' on the appropriate source or destination fields where
    possible, instead of bare numbers
(c) dropping redundant checks, per below.

Regarding redundant checks: the beginning of the loop has this:

                if (pos + 2 + pos[1] > end)
                        break;

but then individual 'case's include stuff like this:

if (pos > end - 3)
return;
if (pos[1] != 1)
return;

Note that the second 'return' (validating the length, pos[1]) combined
with the above condition (ensuring 'pos + 2 + length' doesn't exceed
'end'), makes the first 'return' (whose 'if' can be reworded as 'pos >
end - pos[1] - 2') redundant. Rather than unwind the magic numbers
there, just drop those conditions.

Fixes: 1e58252e334d ("mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

namei: only return -ECHILD from follow_dotdot_rcu()

commit 2b98149c2377bff12be5dd3ce02ae0506e2dd613 upstream.

It's over-zealous to return hard errors under RCU-walk here, given that
a REF-walk will be triggered for all other cases handling ".." under
RCU.

The original purpose of this check was to ensure that if a rename occurs
such that a directory is moved outside of the bind-mount which the
resolution started in, it would be detected and blocked to avoid being
able to mess with paths outside of the bind-mount. However, triggering a
new REF-walk is just as effective a solution.

Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Fixes: 397d425dc26d ("vfs: Test for and handle paths that are unreachable from their mnt_root")
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ena: make ena rxfh support ETH_RSS_HASH_NO_CHANGE

commit 470793a78ce344bd53d31e0c2d537f71ba957547 upstream.

As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing
the key or indirection table using ethtool while keeping the same hash
function.

Also add a function for retrieving the current hash function from
the ena-com layer.

Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: no peer ID in CLC decline for SMCD

commit 369537c97024dca99303a8d4d6ab38b4f54d3909 upstream.

Just SMCR requires a CLC Peer ID, but not SMCD. The field should be
zero for SMCD.

Fixes: c758dfddc1b5 ("net/smc: add SMC-D support in CLC messages")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: atlantic: fix potential error handling

commit 380ec5b9af7f0d57dbf6ac067fd9f33cff2fef71 upstream.

Code inspection found that in case of mapping error we do return current
'ret' value. But beside error, it is used to count number of descriptors
allocated for the packet. In that case map_skb function could return '1'.

Changing it to return zero (number of mapped descriptors for skb)

Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: atlantic: fix use after free kasan warn

commit a4980919ad6a7be548d499bc5338015e1a9191c6 upstream.

skb->len is used to calculate statistics after xmit invocation.

Under a stress load it may happen that skb will be xmited,
rx interrupt will come and skb will be freed, all before xmit function
is even returned.

Eventually, skb->len will access unallocated area.

Moving stats calculation into tx_clean routine.

Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Reported-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: netlink: cap max groups which will be considered in netlink_bind()

commit 3a20773beeeeadec41477a5ba872175b778ff752 upstream.

Since nl_groups is a u32 we can't bind more groups via ->bind
(netlink_bind) call, but netlink has supported more groups via
setsockopt() for a long time and thus nlk->ngroups could be over 32.
Recently I added support for per-vlan notifications and increased the
groups to 33 for NETLINK_ROUTE which exposed an old bug in the
netlink_bind() code causing out-of-bounds access on archs where unsigned
long is 32 bits via test_bit() on a local variable. Fix this by capping the
maximum groups in netlink_bind() to BITS_PER_TYPE(u32), effectively
capping them at 32 which is the minimum of allocated groups and the
maximum groups which can be bound via netlink_bind().

CC: Christophe Leroy <christophe.leroy@c-s.fr>
CC: Richard Guy Briggs <rgb@redhat.com>
Fixes: 4f520900522f ("netlink: have netlink per-protocol bind function return an error code.")
Reported-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/qeth: vnicc Fix EOPNOTSUPP precedence

commit 6f3846f0955308b6d1b219419da42b8de2c08845 upstream.

When getting or setting VNICC parameters, the error code EOPNOTSUPP
should have precedence over EBUSY.

EBUSY is used because vnicc feature and bridgeport feature are mutually
exclusive, which is a temporary condition.
Whereas EOPNOTSUPP indicates that the HW does not support all or parts of
the vnicc feature.
This issue causes the vnicc sysfs params to show 'blocked by bridgeport'
for HW that does not support VNICC at all.

Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>