Daniel Mack [Tue, 23 Jun 2009 15:30:04 +0000 (17:30 +0200)]
pxa: add clock for system bus 2 arbiter
This clock is needed for systems using the USB2 device unit or the 2d
graphics accelerator.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Grazvydas Ignotas [Tue, 7 Jul 2009 21:30:01 +0000 (00:30 +0300)]
OMAP3 pandora: Fix CKE1 MUX setting to allow self-refresh
Pandora is using both SDRC CSes. The MUX setting is needed
for the second CS clock signal to allow the 2 RAM parts to
be put in self-refresh correctly.
Based on similar patch for beagle and overo by
Jean Pihet and Steve Sakoman.
Grazvydas Ignotas [Tue, 7 Jul 2009 21:30:00 +0000 (00:30 +0300)]
OMAP3 pandora: setup pulls for various GPIOs
Set pullups or pulldowns for GPIOs which need them.
Disable them for others, which have external pulls.
Also make disabled pull setting consistent (some pins had
type set to "up" even if pull type selection was disabled).
Grazvydas Ignotas [Tue, 7 Jul 2009 21:29:59 +0000 (00:29 +0300)]
OMAP3 pandora: setup pin mux for pins used on rev3 boards
Setup pin mux for GPIO pins connected on rev3 or later
boards. Also change NUB2 IRQ pin. This should not affect
older boards because they don't have any nubs (analog
controllers) attached to them.
Grazvydas Ignotas [Tue, 7 Jul 2009 21:29:58 +0000 (00:29 +0300)]
OMAP3 pandora: pin mux cleanup
Remove configuration of not unused pins, effectively
leaving them in safe mode.
Prafulla Wadaskar [Mon, 6 Jul 2009 10:20:47 +0000 (15:50 +0530)]
arm: Kirkwood: bugfix: UART1 bar correction
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Kumar Gala [Tue, 7 Jul 2009 20:48:58 +0000 (15:48 -0500)]
usb: Fix compiler warning with gcc4.4
ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Nobuhiro Iwamatsu [Wed, 8 Jul 2009 02:42:19 +0000 (11:42 +0900)]
sh: Update pci config for Renesas r7780mp board
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 25 Jun 2009 07:31:26 +0000 (16:31 +0900)]
sh: Add support ESPT-GIGA borad
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Matthias Fuchs [Fri, 3 Jul 2009 14:06:37 +0000 (16:06 +0200)]
Add ESD PCI vendor ID
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Peter Tyser [Mon, 22 Jun 2009 23:01:41 +0000 (18:01 -0500)]
api_examples/Makefile: General cleanup
* Remove symlinking of files located outside api_examples/
* Auto generate dependencies for files located outside api_examples/
* Update names of variables to be similar to those in tools/Makefile
* Fix out of tree build error
Dependencies are calculated for all files in the SRCS variable.
Previously, the SRCS variable contained files which were symlinked
into the api_examples/ directory. These symlinked files did not exist
when dependencies were calculated when building out of tree. This
resulted in errors such as:
make[1]: *** No rule to make target `/work/wd/tmp-ppc/api_examples/.depend', needed by `_depend'. Stop.
make[1]: Leaving directory `/home/wd/git/u-boot/work/api_examples'
make: *** [depend] Error 2
Since symlinked source files are no longer used, this bug no longer
exists.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
Peter Tyser [Mon, 22 Jun 2009 23:01:40 +0000 (18:01 -0500)]
api_examples/Makefile: Get rid of unnecessary intermediate LIB target
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
Peter Tyser [Mon, 22 Jun 2009 23:01:39 +0000 (18:01 -0500)]
api_examples/Makefile: Combine ELF and BIN targets
Combining the two rules cleans up the Makefile a bit
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
Peter Tyser [Mon, 22 Jun 2009 23:01:38 +0000 (18:01 -0500)]
api_examples/Makefile: Split up variable declarations
This cleans up the Makefile a bit and simplifies future changes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
Timur Tabi [Fri, 19 Jun 2009 19:10:52 +0000 (14:10 -0500)]
remove _IO_BASE and KSEG1ADDR from board configuration files
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.
The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Jon Smirl [Sun, 14 Jun 2009 22:21:28 +0000 (18:21 -0400)]
board support patch for phyCORE-MPC5200B-tiny
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Mike Frysinger [Mon, 15 Jun 2009 17:37:20 +0000 (13:37 -0400)]
kallsyms: fix escaping of NUL char in strings
The current kallsyms code is using \\0 to escape the backslash in the awk
code, but the shell too needs escaping. This way we make sure gcc is
passed the \0. Then gcc itself will consume this as an octal, so we have
to use 000 so gcc will create the final NUL.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Harald Krapfenbauer [Fri, 26 Jun 2009 14:18:49 +0000 (10:18 -0400)]
Blackfin: cm-bf561: add example settings for EXT-BF5xx-USB-ETH2 add-on
The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender
board, so add a simple example of how to do that in the board config.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 25 Jun 2009 23:40:28 +0000 (19:40 -0400)]
Blackfin: blackstamp: update spi flash settings
The latest blackstamp boards can only run the SPI flash at 15MHz before
they start to crap out, so lower the max speeds accordingly. The new SPI
flash also has different sector requirements, so update the environment
sizes as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 6 Oct 2008 07:31:52 +0000 (03:31 -0400)]
Blackfin: add cache_dump commands
A few debug-type commands used to dump the raw icache/dcache data. Useful
when trying to track down cache-related bugs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Matthias Fuchs [Wed, 8 Jul 2009 13:31:57 +0000 (15:31 +0200)]
ppc4xx: Set default PCI device ID for 405EP boards
Current code only sets the PCI vendor id to 0x1014 and
leaved device id to 0x0000.
Ths patch ....
a) uses the correct PCI_VENDOR_ID_IBM macro for this
b) sets the default device ID as stated in the UM to 0x0156
by using PCI_DEVICE_ID_IBM_405GP for this.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Wed, 8 Jul 2009 11:43:55 +0000 (13:43 +0200)]
ppc4xx: Move 405EP pci code from cpu_init_f() to __pci_pre_init()
This patch moves some basic PCI initialisation from the 4xx cpu_init_f()
to cpu/ppc4xx/4xx_pci.c.
The original cpu_init_f() function enabled the 405EP's internal arbiter
in all situations. Also the HCE bit in cpc0_pci is always set.
The first is not really wanted for PCI adapter designs and the latter
is a general bug for PCI adapter U-Boots. Because it enables
PCI configuration by the system CPU even when the PCI configuration has
not been setup by the 405EP. The one and only correct place is
in pci_405gp_init() (see "Set HCE bit" comment).
So for compatibility reasons the arbiter is still enabled in any case,
but from weak pci_pre_init() so that it can be replaced by board specific
code.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Wed, 8 Jul 2009 11:43:23 +0000 (13:43 +0200)]
ppc4xx: Make is_pci_host() available for all 440 and 405 CPUs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Prafulla Wadaskar [Mon, 29 Jun 2009 15:26:43 +0000 (20:56 +0530)]
usb: add Marvell Kirkwood ehci host controller driver
This driver is tested on Sheevaplug platform
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Vivek Mahajan [Wed, 24 Jun 2009 04:38:40 +0000 (10:08 +0530)]
mpc83xx: USB: fix: access of ehci struct elements
It fixes the access to the 'ehci' struct elements for mpc83xx which
should have been taken care of in
4ef01010aa4799c759d75e67007fdd3a38c88c8a
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Vivek Mahajan [Fri, 19 Jun 2009 12:26:00 +0000 (17:56 +0530)]
mpc8xxx: USB: fix: access of ehci struct elements
This patch fixes the access to the 'ehci' struct elements which should
have been taken care off in
4ef01010aa4799c759d75e67007fdd3a38c88c8a
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Bryan Wu [Tue, 16 Jun 2009 09:26:27 +0000 (05:26 -0400)]
usb: musb: add timeout via CONFIG_MUSB_TIMEOUT
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Mike Frysinger [Tue, 16 Jun 2009 09:26:25 +0000 (05:26 -0400)]
usb: musb: drop old musb read/write prototypes
These functions are no longer defined, so remove their prototypes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Kim Phillips [Mon, 15 Jun 2009 16:50:07 +0000 (11:50 -0500)]
usb: fix CONFIG_SYS_MPC83xx_USB_ADDR not defined error
fix a stray CONFIG_MPC83XX that escaped commit
0f898604945af4543c1525fc33b6bae621a3b805.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Michal Simek [Tue, 30 Jun 2009 13:47:30 +0000 (23:47 +1000)]
asm-generic: Consolidate errno.h to asm-generic/errno.h
This patch use blackfin errno.h implementation which
correspond Linux kernel one.
MIPS implemetation is different that's why I keep it.
I removed ppc_error_no.h from Marvell boards which
was the same too.
I have got ack from ppc40x, blackfin, arm, coldfire and avr custodians.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Simon Kagstrom [Tue, 7 Jul 2009 14:01:02 +0000 (16:01 +0200)]
Command improvements for ubifs
Check that an argument is passed to ubifsmount and that addresses and
sizes are actually numbers for ubifsload. Also improve the instructions
a bit.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Simon Kagstrom [Tue, 7 Jul 2009 14:59:46 +0000 (16:59 +0200)]
Handle VID header offset in ubi part command
The VID header offset is sometimes needed to initialize the UBI
partition. This patch adds it (optionally) to the command line
for the ubi part command.
(Lines have been properly wrapped since last version)
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Thu, 9 Jul 2009 07:56:16 +0000 (09:56 +0200)]
MAINTAINERS: fix sorting, remove duplicates.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 8 Jul 2009 20:01:54 +0000 (22:01 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Wed, 8 Jul 2009 20:01:50 +0000 (22:01 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Wed, 8 Jul 2009 19:51:17 +0000 (21:51 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Heiko Schocher [Wed, 10 Dec 2008 07:27:01 +0000 (08:27 +0100)]
all platforms: make show_boot_progress() work again
Signed-off-by: Heiko Schocher <hs@denx.de>
Prafulla Wadaskar [Mon, 29 Jun 2009 09:55:18 +0000 (15:25 +0530)]
nand: Add Marvell Kirkwood NAND driver
This patch adds a NAND driver for the Marvell Kirkwood SoC's
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Matthias Fuchs [Mon, 6 Jul 2009 14:27:33 +0000 (16:27 +0200)]
ppc4xx: Make pll_write global
This patch makes pll_write on PPC405EP boards
global and callable from C code.
pll_write can be used to dynamically modify the PLB:PCI divider
as it is required for 33/66 MHz pci adapters based on the 405EP.
board_early_init_f() is a good place to do that (check M66EN signal
and call pll_write() when it is required).
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 6 Jul 2009 09:44:33 +0000 (11:44 +0200)]
ppc4xx: Remove compilation warning "pci_async_enabled defined but not used"
Signed-off-by: Stefan Roese <sr@denx.de>
Matthias Fuchs [Fri, 3 Jul 2009 14:06:06 +0000 (16:06 +0200)]
ppc4xx: Implement is_pci_host() for 405 CPUs
This patch implements the is_pci_host() function in a similiar way
as it is used on 440 targets.
The former path with CONFIG_PCI_HOST == PCI_HOST_AUTO does not
build on 405EP targets because checking the PCI arbiter is different.
So putting the fixed code into a separate function makes the code
more readable.
Also using is_pci_host() on 405 brings 405 and 440 PCI code
a little bit closer.
In preparation for an upcoming 405EP based PMC module I made this
function weak so that it can be overwritten from board specific code.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Alessio Centazzo [Thu, 2 Jul 2009 05:20:51 +0000 (22:20 -0700)]
ppc4xx: Fixed PPC4xx debug compilation error in uic.c
This patch fixes a debug compilation error for PPC4xx platforms, all
other architectures are not affected by this change. The 'handler'
pointer was undefined. The fix is exercised and has effect only if
DEBUG is defined.
Signed-off-by: Alessio Centazzo acpatin@yahoo.com
Signed-off-by: Stefan Roese <sr@denx.de>
Felix Radensky [Wed, 1 Jul 2009 08:37:46 +0000 (11:37 +0300)]
4xx: Fix compilation warnings and MQ registers dump in SPD DDR2 code
This patch fixes printf format string compilation warnings in several
debug statements. It also fixes the dump of DDR controller MQ registers
found on some 44x and 46x platforms. The current register dump code
uses incorrect DCRs to access these registers.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Felix Radensky [Mon, 22 Jun 2009 12:30:42 +0000 (15:30 +0300)]
ppc4xx: Fix FDT EBC mappings on Canyonlands
This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Nobuhiro Iwamatsu [Tue, 16 Jun 2009 13:29:15 +0000 (22:29 +0900)]
sh: Revised the build with newest compiler
The check of data became severe from newest gcc.
This patch checked in gcc-4.2 and 4.3 .
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 4 Jun 2009 10:06:48 +0000 (12:06 +0200)]
sh3/sh4: rename config option TMU_CLK_DIVIDER to CONFIG_SYS_TMU_CLK_DIV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 4 Jun 2009 10:06:47 +0000 (12:06 +0200)]
sh3/sh4: fix CONFIG_SYS_HZ to 1000
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 4 Jun 2009 10:06:46 +0000 (12:06 +0200)]
sh: introduce clock framework
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 4 Jun 2009 10:06:45 +0000 (12:06 +0200)]
sh: unify linker script
all sh boards use the same cpu linker script so move it to cpu/$(CPU)
that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 4 Jun 2009 10:06:44 +0000 (12:06 +0200)]
sh: make the linker scripts more generic
currently we need to sync the linker script enty and TEXT_BASE manualy
and the reloc_dst is based on it
instead provide it now from the ldflags
tested on r2dplus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 4 Jun 2009 10:06:43 +0000 (12:06 +0200)]
sh7785lcr: fix out of tree build
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
HeungJun Kim [Tue, 30 Jun 2009 05:42:22 +0000 (14:42 +0900)]
env_onenand: change env_address type from unsigned long to loff_t
If use the onenand boot, the env_relocate_spec() calls mtd->read(),
and the type of the argument #2 of mtd->read() was changed to loff_t.
But, the "env_addr" type is still unsigned long, thus this patch change
the type from unsigned long to loff_t.
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Mingkai Hu [Thu, 18 Jun 2009 10:23:27 +0000 (18:23 +0800)]
fsl_elbc_nand: redirect the pointer of bbt pattern to RAM
The bbt descriptors contains the pointer to the bbt pattern which
are statically initialized memory struct. When relocated to RAM,
these pointers will continue point to NOR flash(or L2 SRAM, or
other boot device). If the contents of NOR flash changed or L2
SRAM disabled, it'll hang the system.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Wed, 24 Jun 2009 22:23:49 +0000 (17:23 -0500)]
nand_spl: Fix cmd_ctrl usage in nand_boot.c.
When adding large page NAND support to this file, I had a misunderstanding
about the exact semantics of NAND_CTRL_CHANGE (which isn't documented
anywhere I can find) -- it is apparently just a hint to drivers,
which aren't required to preserve the old value for subsequent
non-"change" invocations.
This change makes nand_boot.c no longer assume this. Note that this
happened to work by chance with some NAND drivers, which don't preserve
the value, but treat 0 equivalently to NAND_CTRL_ALE.
I don't have hardware to test this, so any testing is appreciated.
Signed-off-by: Scott Wood <scottwood@freescale.com>
kevin.morfitt@fearnside-systems.co.uk [Thu, 18 Jun 2009 17:41:03 +0000 (18:41 +0100)]
Bug-fix in drivers mtd nand Makefile
The S3C2410 NAND driver source file is included in the makefile instead of
the object file.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Guennadi Liakhovetski [Mon, 18 May 2009 14:07:22 +0000 (16:07 +0200)]
nand_spl: read environment early, when booting from NAND using nand_spl
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 16 May 2009 12:27:40 +0000 (14:27 +0200)]
mtd: nand: use loff_t for offset
nand_util currently uses size_t which is arch dependent and not always a
unsigned long. Now use loff_t, as does the linux mtd layer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Denk [Sun, 24 May 2009 15:34:33 +0000 (17:34 +0200)]
nand/onenand: Fix missing argument checking for "markbad" command
The "nand markbad" and "onenand markbad" commands did not check if an
argument was passed; if this was forgotten, no error was raised but
block 0 was marked as bad.
While fixing this bug, clean up the code a bit and allow to pass more
than one block address, thus allowing to mark several blocks as bad
in a single command invocation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Mike Frysinger [Tue, 26 May 2009 02:42:28 +0000 (22:42 -0400)]
mtd: nand: new base driver for memory mapped nand devices
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Guennadi Liakhovetski [Mon, 18 May 2009 14:06:45 +0000 (16:06 +0200)]
env_nand: remove unused variable.
Remove an unused "total" variable in multiple functions.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
David Brownell [Sun, 10 May 2009 22:43:01 +0000 (15:43 -0700)]
davinci_nand chipselect/init cleanup
Update chipselect handling in davinci_nand.c so that it can
handle 2 GByte chips the same way Linux does: as one device,
even though it has two halves with independent chip selects.
For such chips the "nand info" command reports:
Device 0: 2x nand0, sector size 128 KiB
Switch to use the default chipselect function unless the board
really needs its own. The logic for the Sonata board moves out
of the driver into board-specific code. (Which doesn't affect
current build breakage if its NAND support is enabled...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Sandeep Paulraj [Sat, 9 May 2009 16:35:20 +0000 (12:35 -0400)]
NAND DaVinci: Update to ALE/CLE Mask values
All DaVinci SOC's use a CLE mask of 0x10 and an ALE mask of 0x8
except the DM646x. This was decided by the design team driving the design.
This patch updates the CLE and ALE values for DM646x.
Updated patches for DM646x will be sent shortly.
This applies to u-boot-nand-flash git
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Sandeep Paulraj [Wed, 29 Apr 2009 13:47:09 +0000 (09:47 -0400)]
ARM DaVinci: Changing ALE Mask Value
The ALE mask used by DaVinci SOCs is wrong. The patch changes the mask value
from '0xa' to '0x8'. This is the mask we use for all TI releases.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
David Brownell [Tue, 28 Apr 2009 20:19:53 +0000 (13:19 -0700)]
davinci_nand: cleanup II (CONFIG_SYS_DAVINCI_BROKEN_ECC)
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option. It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).
DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC. The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages. Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.
Since this option itself seems broken, remove it. Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
David Brownell [Tue, 28 Apr 2009 20:19:50 +0000 (13:19 -0700)]
davinci_nand: cleanup I (minor)
Minor cleanup for DaVinci NAND code:
- Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
be defined when there are multiple chipselect lines in use
(as with common 2 GByte chips).
- Cleanup handling of EMIF control registers
* Only need one pointer pointing to them
* Remove incorrect and unused struct supersetting them
- Use the standard waitfunc; we don't need a custom version
- Partial legacy cleanup:
* Don't initialize every board like it's a DM6446 EVM
* #ifdef a bit more code for BROKEN_ECC
Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Denk [Tue, 7 Jul 2009 21:18:03 +0000 (23:18 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Wolfgang Denk [Tue, 7 Jul 2009 20:35:02 +0000 (22:35 +0200)]
Coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 7 Jul 2009 20:22:05 +0000 (22:22 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 7 Jul 2009 19:06:07 +0000 (21:06 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx
Wolfgang Denk [Tue, 7 Jul 2009 18:58:30 +0000 (20:58 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ubi
Wolfgang Denk [Tue, 7 Jul 2009 18:56:56 +0000 (20:56 +0200)]
Merge branch 'sf' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Tue, 7 Jul 2009 18:54:12 +0000 (20:54 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Stefan Roese [Mon, 29 Jun 2009 11:30:50 +0000 (13:30 +0200)]
UBI: Fix build problem noticed on Apollon (arm/testing repo)
This patch fixes a build problem noticed on Apollon by using
mtd_dev_by_eb() instead of "/" as done in the Linux UBI version.
So this brings the U-Boot UBI version more in sync with the Linux
version again.
Signed-off-by: Stefan Roese <sr@denx.de>
Prafulla Wadaskar [Mon, 6 Jul 2009 14:59:15 +0000 (20:29 +0530)]
sf: Macronix additional chips supported
new chips supported:-
MX25L1605D, MX25L3205D, MX25L6405D, MX25L12855E
out of which MX25L6405D and MX25L12855E tested on Kirkwood platforms
Modified the Macronix flash support to use 2 bytes of device id instead of 1
This was required to support MX25L12855E
Signed-off-by: Piyush Shah <spiyush@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Fri, 19 Jun 2009 07:27:28 +0000 (03:27 -0400)]
sf: sst: add sst25vf###b ids
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Fri, 19 Jun 2009 07:20:06 +0000 (03:20 -0400)]
sf: sst: fix sector size
Looks like when I was encoding the sector sizes, I forgot to divide by 8
(due to the stupid marketing driven process that declares all sizes in
useless megabits and not megabytes).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 4 Jul 2009 23:06:06 +0000 (01:06 +0200)]
nhk8815: fix MAKEALL
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Magnus Lilja [Sat, 4 Jul 2009 08:31:24 +0000 (10:31 +0200)]
MX31: Add NAND SPL boot support to i.MX31 PDK board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Prafulla Wadaskar [Mon, 29 Jun 2009 15:25:54 +0000 (20:55 +0530)]
arm: Kirkwood: arch specific updated for ehci-Kirkwood driver support
This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Alessandro Rubini [Mon, 29 Jun 2009 08:52:37 +0000 (10:52 +0200)]
arm nomadik: use 1000 as HZ value and rewrite timer code
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Alessandro Rubini [Mon, 22 Jun 2009 07:18:57 +0000 (09:18 +0200)]
arm nomadik: allow Nand and OneNand to coexists
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Alessandro Rubini [Mon, 22 Jun 2009 07:18:47 +0000 (09:18 +0200)]
arm nomadik: cleanup reset
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Alessandro Rubini [Mon, 22 Jun 2009 07:18:37 +0000 (09:18 +0200)]
arm nomadik: rename board to nhk8815
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Stefano Babic [Wed, 1 Jul 2009 18:40:41 +0000 (20:40 +0200)]
xscale: add support for the polaris board
The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Wed, 1 Jul 2009 02:33:56 +0000 (04:33 +0200)]
xscale: fix USB initialization for Trizepsiv module
Due to change in the usb_board_init() prototype, the USB for
the TrizepsIV was not correctly initialized.
Removed dummy print from usb_board_stop().
Signed-off-by: Stefano Babic <sbabic@denx.de>
Prafulla Wadaskar [Wed, 1 Jul 2009 18:34:51 +0000 (20:34 +0200)]
net: merge bugfix: Marvell Kirkwood gigabit ethernet driver
This patch looks okay on u-boot-net.git/next branch
but when it was merged to u-boot.git/master the last line is missing
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
Daniel Gorsulowski [Tue, 30 Jun 2009 19:03:37 +0000 (21:03 +0200)]
at91: Add esd gmbh MEESC board support
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 30 Jun 2009 19:03:35 +0000 (21:03 +0200)]
ARM: Update mach-types
update against linux v2.6.30
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Daniel Gorsulowski [Tue, 30 Jun 2009 21:03:33 +0000 (23:03 +0200)]
at91: Add CAN init function
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Simon Kagstrom [Tue, 30 Jun 2009 21:03:31 +0000 (23:03 +0200)]
arm: Kirkwood: Correct header define
Correct define typo (. -> ,)
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Magnus Lilja [Tue, 30 Jun 2009 23:07:55 +0000 (01:07 +0200)]
MX31: Add basic support for Freescale i.MX31 PDK board.
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 22 Jun 2009 22:12:01 +0000 (00:12 +0200)]
S3C24x0: extract interrupts from timer
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 28 Jun 2009 12:14:21 +0000 (14:14 +0200)]
dm355/pm9261: add missing CONFIG_NET_MULTI
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 22 Jun 2009 22:12:01 +0000 (00:12 +0200)]
arm920t/interrupts: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Kim, Heung Jun [Sat, 20 Jun 2009 09:02:17 +0000 (11:02 +0200)]
move L2 cache enable/disable function to cache.c in the omap3 SoC directory
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
CC: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Thomas Lange [Sat, 20 Jun 2009 09:02:17 +0000 (11:02 +0200)]
ARM DaVinci: EMIF settings
NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.
Without this patch, EMIF configurations made in board_init()
will be invalidated.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 20 Jun 2009 09:02:17 +0000 (11:02 +0200)]
versatile: config coding style cleanup
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Peter Pearse <peter.pearse@arm.com>
Prafulla Wadaskar [Sat, 20 Jun 2009 09:01:53 +0000 (11:01 +0200)]
arm: Kirkwood: Basic SOCs support
Kirkwood family controllers are highly integrated SOCs
based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core.
SOC versions supported:-
1) 88F6281-A0 define CONFIG_KW88F6281_A0
2) 88F6192-A0 define CONFIG_KW88F6192_A0
Other supported features:-
1) get_random_hex() fucntion
2) PCI Express port initialization
3) NS16550 driver support
Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Acked-by: Stefan Rose <sr@denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Prafulla Wadaskar [Sat, 20 Jun 2009 09:01:52 +0000 (11:01 +0200)]
arm: generic cache.h for ARM architectures
This patch is required for Kirkwood SoC support
may be used by other ARM architectures
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Matthias Ludwig [Sat, 20 Jun 2009 09:01:50 +0000 (11:01 +0200)]
OMAP3EVM: fix typo. replace CS6 by CS5, no functionality change
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>