Michal Simek [Tue, 24 Jan 2023 15:19:26 +0000 (16:19 +0100)]
xilinx: board: Use ETH_ALEN macro for mac address size
Use predefined macro for eth_mac legacy format.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/382d4bff370894164fad3c30ac0400b25142b544.1674573561.git.michal.simek@amd.com
Stefan Roese [Wed, 25 Jan 2023 07:09:08 +0000 (08:09 +0100)]
net: zynq_gem: Wait for SGMII PCS link in zynq_gem_init()
In our system using ZynqMP with an external SGMII PHY it's necessary
to wait for the PCS link and auto negotiation to finish before the xfer
starts. Otherwise the first packet(s) might get dropped, resulting in a
delay at the start of the ethernet transfers.
This is only done when the PHY link is already up, which is done in
phy_startup(). As waiting for the PHY link bits via pcsstatus does not
make much sense, when the link is not available in general (e.g. no
cable connected).
This patch adds the necessary code including a minimal delay of 1 ms
which fixes problems of dropped first packages.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Katakam Harini <harini.katakam@amd.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20230125070908.1343256-1-sr@denx.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
Algapally Santosh Sagar [Fri, 20 Jan 2023 05:36:17 +0000 (22:36 -0700)]
drivers: mmc: Change datatype of tuning_loop_counter to int
tuning_loop_counter is of char type, which is not capable of handling
the entire data range of this variable. This is pointed by below sparse
warning. Change datatype to int to fix this.
warning: comparison is always false due to limited range of data type.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230120053617.32463-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Algapally Santosh Sagar [Fri, 20 Jan 2023 05:36:16 +0000 (22:36 -0700)]
xilinx: versal: Add missing header
Add missing prototype to fix the sparse warning, warning: no
previous prototype for 'do_go_exec' [-Wmissing-prototypes].
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230120053617.32463-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Algapally Santosh Sagar [Fri, 20 Jan 2023 05:36:15 +0000 (22:36 -0700)]
gpio: zynqmp: Handle error from get_gpio_modepin
There is a unused variable ret, due to which we are getting sparse warning
as below.
warning: variable 'ret' set but not used [-Wunused-but-set-variable].
Return ret incase of error.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230120053617.32463-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Algapally Santosh Sagar [Fri, 20 Jan 2023 05:36:14 +0000 (22:36 -0700)]
xilinx: common: Include header file to fix warning
Prototype is missing for board_get_usable_ram_top, which is pointed by
below sparse warning. Include init.h header file to fix this.
warning: no previous prototype for 'board_get_usable_ram_top'
[-Wmissing-prototypes].
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230120053617.32463-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Michal Simek [Thu, 19 Jan 2023 09:46:59 +0000 (10:46 +0100)]
arm64: versal-net: Enable remaking ELF from bin
U-Boot is composing u-boot.bin from u-boot-nodtb.bin with appended
dts/dt.dtb. It means U-Boot doesn't have DTB inside. When REMAKE_ELF is
enabled make will also create u-boot.elf which is recreated from
u-boot.bin. Below is build output for mini configuration how ELF is
recreated.
cat arch/arm/dts/versal-net-mini.dtb > dts/dt.dtb
cat u-boot-nodtb.bin dts/dt.dtb > u-boot-dtb.bin
cp dts/dt.dtb u-boot.dtb
cp u-boot-dtb.bin u-boot.bin
aarch64-linux-gnu-objcopy -I binary -B aarch64 -O elf64-littleaarch64
u-boot.bin u-boot-elf.o
aarch64-linux-gnu-ld.bfd u-boot-elf.o -o u-boot.elf -EL -T u-boot-elf.lds
--defsym="_start"=0xBBF00000 -Ttext=0xBBF00000
It is useful to have u-boot.elf present because Xilinx XSDB debugger can
load ELF file and user doesn't need to specify loading address for
u-boot.bin.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ca550c5c4bf908e757a49a83fdfab0e7100de45e.1674121617.git.michal.simek@amd.com
Ovidiu Panait [Wed, 25 Jan 2023 16:41:57 +0000 (18:41 +0200)]
microblaze: spl: disable falcon mode by default
Drop falcon mode configs from microblaze-generic_defconfig, so that a
defconfig build will still boot into u-boot proper.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230125164157.1638680-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ovidiu Panait [Wed, 25 Jan 2023 16:41:56 +0000 (18:41 +0200)]
microblaze: spl: drop boot_linux
Drop boot_linux variable as it is not assigned anywhere. Now that there is
no variable controlling linux boot in spl_start_uboot(), make this
function always return false when falcon mode is enabled.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230125164157.1638680-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Ovidiu Panait [Wed, 25 Jan 2023 16:41:55 +0000 (18:41 +0200)]
microblaze: spl: wrap spl_start_uboot() in SPL_OS_BOOT ifdefs
Make spl_start_uboot() available only if CONFIG_SPL_OS_BOOT is enabled,
since it is only used for falcon mode.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230125164157.1638680-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Michal Simek [Wed, 18 Jan 2023 12:11:59 +0000 (13:11 +0100)]
arm64: zynqmp: Add support for Kria K24 SOM
SOM itself from PS point of view is using the same configuration as K26
that's why reuse that files and only change compatible strings.
The reason for creating own set of files is just in case when versions
start to diverge because of HW change, supply chain issue, etc.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/61f877ec0b480c5bd368a1211fc73ff7465016bd.1674043915.git.michal.simek@amd.com
Michal Simek [Wed, 18 Jan 2023 12:04:14 +0000 (13:04 +0100)]
arm64: zynqmp: Fill model name for SOM CCs
When U-Boot do DTB reselection origin model for SOM is used and from log it
is not visible if DTB was switched or not. That's why add model directly to
CC (carrier card) to show new model if reselection was successful.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/49ba1007218496c48d287454e84a5b8c08abc692.1674043452.git.michal.simek@amd.com
Michal Simek [Wed, 18 Jan 2023 11:26:43 +0000 (12:26 +0100)]
arm64: versal: Remove xilinx_versal_mini_qspi.h configs
The commit
eaf6ea6a1dc1 ("Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using
system-constants.h") moved custom init stack pointer address to Kconfig
which ends up in situation that xilinx_versal_mini_qspi.h is not
needed anymore. That's why remove the file and move defconfigs directly to
xilinx_versal_mini.h configuration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2d7276ab8d4cb1d245b64287fb59c79325513f22.1674041200.git.michal.simek@amd.com
Michal Simek [Wed, 18 Jan 2023 11:12:57 +0000 (12:12 +0100)]
arm64: zynqmp: Remove xilinx_zynqmp_mini_emmc/qspi.h configs
The commit
eaf6ea6a1dc1 ("Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using
system-constants.h") moved custom init stack pointer address to Kconfig
which ends up in situation that xilinx_zynqmp_mini_emmc/qspi.h are not
needed anymore. That's why remove files and move defconfigs directly to
xilinx_zynqmp_mini.h configuration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/61ae40cf63aabd08adb386c870d3392b0b606fc9.1674040373.git.michal.simek@amd.com
Michal Simek [Wed, 18 Jan 2023 08:25:26 +0000 (09:25 +0100)]
soc: zynqmp: Fix IDcode for xck24
ID code was added by commit
ddf8deabc39d ("arm64: zynqmp: Add support for
SVD devices") based on documentation but after receiving part new ID code
came up. That's why fix IDcode to match xck24 module.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7b39aeeec211458ba4132a10beb7ad295eedb87f.1674030324.git.michal.simek@amd.com
Michal Simek [Fri, 6 Jan 2023 08:38:52 +0000 (09:38 +0100)]
xilinx: common: Add support for partial string match in board_fit_config_name_match()
Board name in FIT image can use U-Boot regular expressions SLRE to instruct
U-Boot to handle all revisions for certain board.
For example when name (description property) is saying "zynqmp-zcu104-revA"
only description with this name is selected.
When zynqmp-zcu104.* is described then all board revisions will be handled
by this fragment.
Xilinx normally have some board revisions which are SW compatible to each
other. That's why make sense to define board name with revisions first
follow by generic description with '.*' at the end like this:
config_1 {
description = "zynqmp-zcu104-rev[AB]";
fdt = "zynqmp-zcu104-revA";
};
config_2 {
description = "zynqmp-zcu104.*";
fdt = "zynqmp-zcu104-revC";
};
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d67683a3c5d0435a5070e622f7a9a38e19c64cf5.1672994329.git.michal.simek@amd.com
Ashok Reddy Soma [Tue, 10 Jan 2023 07:44:07 +0000 (08:44 +0100)]
xilinx: versal-net: Add support for timer and start it
Add support for starting timer by setting up time stamp generator
registers. This is done only for EL3 i.e. mini U-Boot case.
For other cases, it will be done TF-A.
Add COUNTER_FREQUENCY and IOU_SWITCH_DIVISOR0 to Kconfig so that they
can be tuned as required.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fcd8b0dc4b45a11f5e753afff42f84738ac813da.1673336645.git.michal.simek@amd.com
Jay Buddhabhatti [Tue, 10 Jan 2023 07:23:44 +0000 (08:23 +0100)]
clk: versal: Return error in case if clock setup failed
Currently probe is getting success even if clock setup is failed
because of that u-boot is trying to access invalid clocks. So return
error if clock setup failed.
Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fa78e71211e5f68f8dc1353b357f96e6283f65a8.1673335422.git.michal.simek@amd.com
Michal Simek [Mon, 19 Dec 2022 15:26:59 +0000 (16:26 +0100)]
board: presidio-asic: Remove CONFIG_TARGET_VENUS
Symbol is not defined anywhere that's why remove it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e34404488b2b46cbb2a10c1663e809ff34287a66.1671463617.git.michal.simek@amd.com
Neal Frager [Wed, 21 Dec 2022 07:54:46 +0000 (07:54 +0000)]
makefile: add multi_dtb_fit dep
With certain gcc compilers, the u-boot.itb is built immediately after dtb
generation. If CONFIG_MULTI_DTB_FIT is used, it is possible that the
fit-dtb.blob is not finished in time.
This patch adds a necessary dependency to guarantee that the fit-dtb.blob
is built before attempting to build the u-boot.itb.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20221221075446.47141-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Luca Ceresoli [Wed, 11 Jan 2023 08:25:54 +0000 (09:25 +0100)]
arm64: zynqmp: remove Avnet UltraZed-EV Starter Kit
Nobody seems interested and able to keep this board supported, and
xilinx_zynqmp_virt_defconfig is supposed to be enough for any zynqmp board.
See the discussion at: https://lore.kernel.org/u-boot/CAPnjgZ3hHbyiFf=_Lp-Wz_XOWBkV-3vK4Q3xp=7bcERw-spNpA@mail.gmail.com/T/#m76d726f1ab3f7074c8105c9a2af2110ac7d18708
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20230111082554.1930782-1-luca.ceresoli@bootlin.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Victor Lim [Mon, 9 Jan 2023 23:49:46 +0000 (15:49 -0800)]
xilinx: versal: enable gigadevice
enabling gigadevice in the related files
Signed-off-by: Victor Lim <vlim@gigadevice.com>
Link: https://lore.kernel.org/r/20230109234946.14540-5-vlim@gigadevice.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Victor Lim [Mon, 9 Jan 2023 23:49:45 +0000 (15:49 -0800)]
arm64: zynqmp: enable gigadevice
enabling gigadevice in the related files
Signed-off-by: Victor Lim <vlim@gigadevice.com>
Link: https://lore.kernel.org/r/20230109234946.14540-4-vlim@gigadevice.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Victor Lim [Mon, 9 Jan 2023 23:49:44 +0000 (15:49 -0800)]
configs: zynq: enable gigadevice
enabling gigadevice in the related files
Signed-off-by: Victor Lim <vlim@gigadevice.com>
Link: https://lore.kernel.org/r/20230109234946.14540-3-vlim@gigadevice.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Victor Lim [Mon, 9 Jan 2023 23:49:43 +0000 (15:49 -0800)]
mtd: spi-nor-ids: add gigadevice part #
adding gigadevice part numbers
Signed-off-by: Victor Lim <vlim@gigadevice.com>
Link: https://lore.kernel.org/r/20230109234946.14540-2-vlim@gigadevice.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Michal Simek [Mon, 12 Dec 2022 14:27:40 +0000 (15:27 +0100)]
arm64: zynqmp: Remove unused snps,refclk_fladj property
The commit
c55ac51a550c ("usb: dwc3: Program GFLADJ") hopefully fixed
issues around fladj logic. This DT property was used in Xilinx stack only
that's why remove because it is not needed anymore.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9bdbd1156b19e28cdebeca29149268b0579a8b6a.1670855257.git.michal.simek@amd.com
Harini Katakam [Mon, 12 Dec 2022 14:14:18 +0000 (15:14 +0100)]
arm64: zynqmp: Enable TI phy reset via GPIO
Add DT property to support reset of TI PHY connected to GEM.
This is present in RevA DT but needs to be extended RevB/1.0/1.1
versions which are built on top.
Fixes:
2b1db7b18c97 ("arm64: zynqmp: Wire GEM reset gpio")
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7b093616ddea269043cbbb1e3806644d5a4b23be.1670854455.git.michal.simek@amd.com
Harini Katakam [Mon, 12 Dec 2022 14:14:17 +0000 (15:14 +0100)]
arm64: zynqmp: Describe TI phy as ethernet phy ID on ZCU102 RevB & up
TI phy requires a reset before PHY address detection to make sure
correct strapping via MIO is detected. Facilitate the same using
ethernet-phy-id compatible string. GPIO reset entry will be added in
a separate commit.
This support is present in RevA but needs to be extended to RevB/1.0/1.1
versions which are built on top.
Fixes:
13622c7a9dfa ("arm64: zynqmp: Describe TI phy as ethernet-phy-id")
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6d500a83a787316353d4b26c75d1b51d29e3730e.1670854455.git.michal.simek@amd.com
Michal Simek [Mon, 12 Dec 2022 14:06:13 +0000 (15:06 +0100)]
arm64: zynqmp: Remove unused USB DT properties
xlnx,usb-polarity, xlnx,usb-reset-mode and snps,mask_phy_reset are not
documented in dt binding and also there is no code associated with them
that's why remove them.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/369139fafa1745252ef687e31aebf6bcc2080a32.1670853972.git.michal.simek@amd.com
Michal Simek [Fri, 9 Dec 2022 15:19:29 +0000 (16:19 +0100)]
net: zynq_gem: Add support for new compatible str with xlnx prefix
cdns prefix was deprecated and replaced by xlnx one.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7d1312d741349451b36558baa3e9132247303992.1670599167.git.michal.simek@amd.com
Michal Simek [Fri, 9 Dec 2022 12:56:41 +0000 (13:56 +0100)]
arm64: zynqmp: Remove id from usb node name
There is no reason to have number in usb node name. This is also sync up
patch with upstream kernel.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7b13db34031af88a5738d2ec2e05d2498ea8c869.1670590595.git.michal.simek@amd.com
Michal Simek [Fri, 9 Dec 2022 12:56:40 +0000 (13:56 +0100)]
arm64: zynqmp: Align gpio-key node names with dtschema
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
It is based on kernel commit (
228e8a88b1915a2b467c83d8d0976605f1272fae).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ae23999097553acb21dfca9288a913bb8b24587a.1670590595.git.michal.simek@amd.com
Michal Simek [Fri, 9 Dec 2022 12:56:39 +0000 (13:56 +0100)]
arm64: zynqmp: Fix AMS device tree node
Aligned node description with the Linux kernel. Node has been added by
kernel commit (
271c1fa01c2307cf74f4656390d6299991119c3e).
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/74188b64cf615100345d058e026cb0d2de0e089b.1670590595.git.michal.simek@amd.com
Michal Simek [Fri, 9 Dec 2022 12:56:38 +0000 (13:56 +0100)]
arm64: zynqmp: Added GEM reset definitions
The Cadence GEM/MACB driver now utilizes the platform-level reset on the
ZynqMP platform. Add reset definitions to the ZynqMP platform device
tree to allow this to be used.
Linux upstream commit (
e461bd6f43f4e568f7436a8b6bc21c4ce6914c36).
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/14e3637735dbc626659e96d142f04a63398362f8.1670590595.git.michal.simek@amd.com
Michal Simek [Fri, 9 Dec 2022 12:56:37 +0000 (13:56 +0100)]
arm64: zynqmp: Sync #dma-cells property location
Sync property location with Linux kernel done by Linux commit
(
1ff2d58e60c8093e9be935b1f191341c0cda957a).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e09ad90ea610a81528ef5ecbc931bc9791b1c653.1670590595.git.michal.simek@amd.com
Tom Rini [Fri, 6 Jan 2023 03:47:44 +0000 (22:47 -0500)]
ns16650: Correct CONFIG_SYS_NS16550_MEM32 platforms
There are currently no platform that are both CONFIG_SYS_NS16550_MEM32
and not (per how the logic was prior to being broken in
0478dac62a9a
("kbuild: Remove uncmd_spl logic")) enabled in CONFIG_DM_SERIAL. We drop
this line out now so that platforms which do use
CONFIG_SYS_NS16550_MEM32 and depending on stage may or may not have
DM_SERIAL set.
Fixes:
0478dac62a9a ("kbuild: Remove uncmd_spl logic")
Reported-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> #on Ringneck PX30, Puma RK3399
Tom Rini [Mon, 9 Jan 2023 16:30:08 +0000 (11:30 -0500)]
Merge branch 'next'
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 9 Jan 2023 16:07:33 +0000 (11:07 -0500)]
Prepare v2023.01
Signed-off-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Sun, 8 Jan 2023 16:17:34 +0000 (21:47 +0530)]
board: rockchip: Fix binman_init failure on EVB-RK3568
For some newer SoCs like RK3568, the Rockchip has not released
any DDR drivers yet so idbloader needs to create manually using
DDR binaries offered by rkbin. This indeed no requirement to
enable TPL in the U-Boot source code.
If we mark TPL disabled and mark BINMAN enabled by default then
there would be an issue of binman_init failure during board
relocation. This is true as binman failed to find the top-level
node like u-boot-tpl here.
Here is the boot issue observed in Radxa-CM3 RK3566 board,
U-Boot 2023.01-rc4-00057-gac2505d463-dirty (Jan 04 2023 - 23:44:18 +0530)
Model: Radxa Compute Module 3(CM3) IO Board
DRAM: 2 GiB
binman_init failed:-2
initcall sequence
000000007ffd2008 failed at call
0000000000a18cac (err=-2)
### ERROR ### Please RESET the board ###
This might be fixed via binman node in rockchip-u-boot.dtsi however
disable BINMAN_FDT for evb-rk3568 defconfig for now as we are at the
end of the release cycle.
Fixes:
05713d570762 ("rockchip: generate u-boot-rockchip.bin with binman
for ARM64 boards")
Cc: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Sun, 8 Jan 2023 18:12:42 +0000 (13:12 -0500)]
Merge tag 'u-boot-nand-
20230108' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next
Pull request for u-boot-nand-
20230108
- rawnand: omap_gpmc: driver model support
Marek Vasut [Thu, 5 Jan 2023 01:26:03 +0000 (02:26 +0100)]
distro_bootcmd: Fix copy-paste error
The "SCRIPT FAILED" string is copied from scan_dev_for_scripts script,
update it so it prints "EXTLINUX FAILED" instead in scan_dev_for_extlinux
script.
Signed-off-by: Marek Vasut <marex@denx.de>
Roger Quadros [Tue, 20 Dec 2022 10:22:03 +0000 (12:22 +0200)]
mtd: rawnand: omap_elm: u-boot driver model support
Support u-boot driver model. We still retain
support legacy way of doing things if ELM_BASE
is defined in <asm/arch/hardware.h>
We could completely get rid of that if all
platforms defining ELM_BASE get rid of that definition
and enable CONFIG_SYS_NAND_SELF_INIT and are verified
to work.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/all/20221220102203.52398-9-rogerq@kernel.org
Link: https://lore.kernel.org/all/CABGWkvrvKiVA_yaDnHJcHEKwc+pEuLdz=i6HQEY0oJQvohCUsw@mail.gmail.com
Roger Quadros [Tue, 20 Dec 2022 10:22:02 +0000 (12:22 +0200)]
dt-bindings: mtd: Add ti, elm DT binding documentation
Adds DT binding documentation for the TI Error Location Module.
This is picked up from the Linux Kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-8-rogerq@kernel.org
Roger Quadros [Tue, 20 Dec 2022 10:22:01 +0000 (12:22 +0200)]
mtd: rawnand: omap_gpmc: Enable SYS_NAND_PAGE_COUNT for OMAP_GPMC
The symbol is required for NAND support in SPL when using
OMAP_GPMC driver.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-7-rogerq@kernel.org
Roger Quadros [Tue, 20 Dec 2022 10:22:00 +0000 (12:22 +0200)]
mtd: rawnand: omap_gpmc: Add SPL NAND support
Enables SPL NAND support for ARCH_K3 by enabling
SPL_NAND_INIT and SPL_SYS_NAND_SELF_INIT.
Legacy OMAP2plus platforms still rely on SPL_NAND_AM33XX_BCH
instead.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-6-rogerq@kernel.org
Roger Quadros [Tue, 20 Dec 2022 10:21:59 +0000 (12:21 +0200)]
mtd: rawnand: omap_gpmc: support u-boot driver model
Adds driver model support.
We need to be able to self initialize the NAND controller/chip
at probe and so enable CONFIG_SYS_NAND_SELF_INIT.
Doing so requires nand_register() API which is provided by nand.c
and needs to be enabled during SPL build via CONFIG_SPL_NAND_INIT.
But nand.c also provides nand_init() so we need to get rid of nand_init()
in omap_gpmc driver if CONFIG_SPL_NAND_INIT is set.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-5-rogerq@kernel.org
Roger Quadros [Tue, 20 Dec 2022 10:21:58 +0000 (12:21 +0200)]
dt-bindings: mtd: Add ti, gpmc-nand DT binding documentation
Add DT binding documentation for the TI GPMC NAND controller.
This is picked up from the Linux Kernel.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-4-rogerq@kernel.org
Roger Quadros [Tue, 20 Dec 2022 10:21:57 +0000 (12:21 +0200)]
mtd: rawnand: nand_base: Allow base driver to be used in SPL without nand_bbt
nand_bbt.c is not being built with the nand_base driver during SPL
build. This results in build failures if we try to access any nand_bbt
related functions.
Don't use any nand_bbt functions for SPL build.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-3-rogerq@kernel.org
Roger Quadros [Tue, 20 Dec 2022 10:21:56 +0000 (12:21 +0200)]
mtd: rawnand: omap_gpmc: Fix BCH6/16 HW based correction
The BCH detection hardware can generate ECC bytes for multiple
sectors in one go. Use that feature.
correct() only corrects one sector at a time so we need to call it
repeatedly for each sector.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-2-rogerq@kernel.org
Tom Rini [Sat, 7 Jan 2023 23:02:26 +0000 (18:02 -0500)]
pylibfdt: Allow version normalization to fail
In some cases, we might not have the sic portion of setuputils
available. Make our import and use of this be done in try/except blocks
as this is done to suppress a run-time warning that is otherwise
non-fatal.
Reported-by: Pali Rohár <pali@kernel.org>
Fixes:
141659187667 ("pylibfdt: Fix disable version normalization")
Signed-off-by: Tom Rini <trini@konsulko.com>
Pali Rohár [Sat, 7 Jan 2023 21:55:26 +0000 (22:55 +0100)]
common/memsize.c: Check for overflow in get_effective_memsize() only for mpc85xx
This reverts commit
777aaaa706bc ("common/memsize.c: Fix
get_effective_memsize() to check for overflow") for non-mpc85xx platforms.
The changes to this generic function, which is intended to help with
32bit platforms with large amounts of memory has unintended side effects
(which in turn lead to boot failures) on other platforms which were
previously functional.
For now do overflow check only for powerpc mpc85xx platform. It is needed
to prevent crashing of P1/P2 boards with 4GB DDR module in 32-bit mode.
Fixes:
777aaaa706bc ("common/memsize.c: Fix get_effective_memsize() to check for overflow")
Signed-off-by: Pali Rohár <pali@kernel.org>
Tom Rini [Sat, 7 Jan 2023 17:32:42 +0000 (12:32 -0500)]
Merge tag 'efi-2023-01-rc5-4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2023-01-rc5-4
UEFI:
* correct the vexpress loaddr which collides with memory used by EFI
* consider the EFI memory map for LMB memory reservation
* avoid RWX section warnings for .data section of *_efi.so files
Heinrich Schuchardt [Wed, 4 Jan 2023 22:43:08 +0000 (23:43 +0100)]
efi_loader: make .data section of *_efi.so files RW
When building with binutils 2.39 warnings
*_efi.so has a LOAD segment with RWX permissions
occur.
Use SHF_WRITE | SHF_ALLOC as section flags for the .data section.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Heinrich Schuchardt [Wed, 4 Jan 2023 00:36:14 +0000 (01:36 +0100)]
lmb: consider EFI memory map
Add reservations for all EFI memory areas that are not
EFI_CONVENTIONAL_MEMORY.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Thu, 5 Jan 2023 17:26:01 +0000 (18:26 +0100)]
efi_loader: carve out efi_get_memory_map_alloc()
Carve out code from efidebug command used to read the memory map.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Wed, 4 Jan 2023 02:17:15 +0000 (03:17 +0100)]
vexpress: adjust loadaddr
On the vexpress_ca9x4 $loadaddr points to a memory area used by the EFI
sub-system. Use the same value as $kernel_addr_r which is safe.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tom Rini [Fri, 6 Jan 2023 16:53:26 +0000 (11:53 -0500)]
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
Tom Rini [Fri, 6 Jan 2023 13:16:15 +0000 (08:16 -0500)]
Merge tag 'u-boot-stm32-
20230106' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp: Fix board_get_usable_ram_top(): workaround to avoid issue after the
commit
777aaaa706b ("common/memsize.c: Fix get_effective_memsize() to check
for overflow") because the effective DDR effective size is reduce by 4KiB
and sometime the board hang on boot
Tom Rini [Fri, 6 Jan 2023 13:14:28 +0000 (08:14 -0500)]
Merge branch '2023-01-06-further-regression-fixes'
- Bring in a number of important regression fixes for among others,
uniphier, PXE booting, socrates, imx7d-pico, rockchip video and
rzg2_beacon as well as making the python version warning fix more
portable.
Adam Ford [Wed, 4 Jan 2023 18:05:43 +0000 (12:05 -0600)]
arm: rmobile: rzg2_beacon: Enable alternative Ethernet PHY
Due to the part shortage, the AR8031 PHY was replaced with a
Micrel KSZ9131. Enabling both config options keeps backward
compatibility with either platform, and both appear to be
auto-detected.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adam Ford [Wed, 4 Jan 2023 15:53:09 +0000 (09:53 -0600)]
arm: dts: rz-g2-beacon-u-boot: Fix QSPI Regression
The QSPI is accessed via the RPC-IF, but the compatible flags
previously used a different name. This compatibel name was changed
which broke the ability to access the QSPI. Fix this by removing
the custom naming reference.
Fixes:
68083b897b57 ("renesas: Fix RPC-IF compatible values")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Philippe Schenker [Wed, 4 Jan 2023 14:43:33 +0000 (15:43 +0100)]
pylibfdt: Fix disable version normalization
On Arch Linux based systems python setuptools does not contain
"setuptools.extern" hence it is failing with the following
error-message:
"
ModuleNotFoundError: No module named 'setuptools.extern'
"
According to a eschwartz `setuptools.extern` is not a public API and
shall not be assumed to be present in the setuptools package. He
mentions that the setuptools project anyway wants to drop this. [1]
Use the correct solution introduced by python setuptools developers to
disable normalization. [2]
[1] https://bbs.archlinux.org/viewtopic.php?id=259608
[2] https://github.com/pypa/setuptools/pull/2026
Fixes:
440098c42e73 ("pylibfdt: Fix version normalization warning")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Wed, 14 Dec 2022 06:45:18 +0000 (07:45 +0100)]
cmd: pxe_utils: Limit fdtcontroladdr usage to non-fitImage
Commit
d5ba6188dfb ("cmd: pxe_utils: Check fdtcontroladdr in label_boot")
forces '$fdtcontroladdr' DT address as a third parameter of bootm command
even if the PXE transfer pulls in a fitImage which contains configuration
node with its own DT that is preferrable to be passed to Linux. Limit the
$fdtcontroladdr fallback utilization to non-fitImages, since it is highly
likely a fitImage would come with its own DT, while single-file images do
need a separate DT.
Fixes:
d5ba6188dfb ("cmd: pxe_utils: Check fdtcontroladdr in label_boot")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peter Hoyes <peter.hoyes@arm.com>
Tested-by: Peter Hoyes <peter.hoyes@arm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Marek Vasut [Sat, 17 Dec 2022 17:41:13 +0000 (18:41 +0100)]
Revert "Revert "cmd: pxe_utils: Check fdtcontroladdr in label_boot""
This reverts commit
ed6251187afabf811a5fd49a44ebd61c53c7b378.
Superseded by "cmd: pxe_utils: Limit fdtcontroladdr usage to non-fitImage"
which is less heavy-handed approach and retains part of the original
behavior for non-fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Jagan Teki [Mon, 2 Jan 2023 18:23:45 +0000 (23:53 +0530)]
rockchip: Fix the broken Video out for rk3288 boards
Video out on RK3288 boards has been broken since from few
releases due to the adding of reset support on vop but
missed enabling DM_RESET on associated boards.
This patch fixes those RK3288 boards.
Cc: Simon Glass <sjg@chromium.org>
Cc: Lin Huang <hl@rock-chips.com>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Fixes: <
9749d2ea29e1> ("rockchip: video: vop: Add reset support")
Reported-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dai Okamura [Fri, 9 Dec 2022 11:38:27 +0000 (20:38 +0900)]
i2c: uniphier-f: correct error recovery
The uniphier i2c block can recognize some handshake errors.
But driver handles all error detections as no error if no timeout.
So this makes unrecoverable state.
This replaces the return values with the right ones to tell the i2c
framework the errors:
- EDEADLK for arbitration lost error
- ENODATA for no answer error
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fabio Estevam [Sat, 31 Dec 2022 16:25:14 +0000 (13:25 -0300)]
imx7d-pico: Fix the name of the u-boot.dtsi file
Since commit
2f96d4dd95f8 ("imx7s/d: synchronise device trees with linux")
the imx7d-pico board no longer boots.
The reason is that prior to the above commit there was an explicit
inclusion of arch/arm/dts/imx7d-pico-u-boot.dtsi inside imx7d-pico.dtsi.
After the syncing with the Linux upstream dtsi, this u-boot.dtsi inclusion
is gone and the board fails to boot.
U-Boot uses the imx7d-pico-pi.dtb file, so rename the u-boot.dtsi to
imx7d-pico-pi-u-boot.dtsi which gets included automatically by U-Boot
standard make logic and makes the board boot again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Pali Rohár [Wed, 28 Dec 2022 18:18:39 +0000 (19:18 +0100)]
powerpc/mpc85xx: socrates: Re-enable building u-boot-socrates.bin
U-Boot build system builds final U-Boot binary for socrates board in custom
file u-boot-socrates.bin (instead of standard u-boot.bin). Output target
file u-boot-socrates.bin is generated by binman as defined in board binman
config file arch/powerpc/dts/socrates-u-boot.dtsi.
But binman was disabled in commit
5af42eafd7e1 ("Makefile: Reduce usage of
custom mpc85xx u-boot.bin target") for all mpc85xx boards which do not use
standard powerpc binman config file arch/powerpc/dts/u-boot.dtsi and boards
which do not require binman at all.
The only such mpc85xx board is socrates. So since that commit, U-Boot does
not final binary for socrates board anymore.
Fix this issue by re-enabling binman for socrates board. And build process
starts again producing u-boot-socrates.bin binary.
Note that build process for this socrates board always produce u-boot.bin
binary which is broken and not usable for socrates board. Long term
solution should be to disable building broken binary u-boot.bin and then
renaming u-boot-socrates.bin to u-boot.bin, or switching to use common
powerpc binman config file arch/powerpc/dts/socrates-u-boot.dtsi (if it is
possible).
Fixes:
5af42eafd7e1 ("Makefile: Reduce usage of custom mpc85xx u-boot.bin target")
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Heiko Schocher <hs@denx.de>
Marek Vasut [Thu, 5 Jan 2023 01:22:22 +0000 (02:22 +0100)]
arm: stm32mp: Fix board_get_usable_ram_top() again
Do not access gd->ram_size and assume this is actual valid RAM size. Since commit
777aaaa706b ("common/memsize.c: Fix get_effective_memsize() to check for overflow")
the RAM size may be less than gd->ram_size , call get_effective_memsize() to get
the limited value instead.
The aforementioned commit makes STM32MP15xx boards with 1 GiB of DRAM
at 0xc0000000 hang on boot, which is a grave defect.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tom Rini [Fri, 6 Jan 2023 03:54:26 +0000 (22:54 -0500)]
Merge tag 'dm-next-5jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
patman enhancements and fixes
Maxim Cournoyer [Tue, 20 Dec 2022 05:28:46 +0000 (00:28 -0500)]
patman: add '--get-maintainer-script' argument
This makes it possible to configure a project to use some other
location or script than the default scripts/get_maintainer.pl one used
in the U-Boot and Linux projects. It can be configured via a .patman
configuration file and accepts arguments, as documented.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Tue, 20 Dec 2022 05:38:41 +0000 (00:38 -0500)]
patman: additionally honor a local .patman config file
This enables versioning a project specific patman configuration file.
It also makes it possible to declare the project name, which is not a
useful thing to do in $HOME/.patman. A new test is added, along
updated documentation.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Tue, 20 Dec 2022 05:38:40 +0000 (00:38 -0500)]
patman: fail early in Setup when provided config file does not exist
Rationale: if the user explicitly provide this argument, they probably
intend for it to be used.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Tue, 20 Dec 2022 05:38:39 +0000 (00:38 -0500)]
patman: set the default config_fname argument value to None
This better matches Python conventions, allowing to easily test
whether the optional argument is provided.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Tue, 20 Dec 2022 05:38:38 +0000 (00:38 -0500)]
patman: import gitutil module where it is needed
Instead of propagating it from the module entry point (main script).
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Tue, 20 Dec 2022 05:38:37 +0000 (00:38 -0500)]
patman: replace deprecated SafeConfigParser with ConfigParser
The SafeConfigParser class has been renamed in Python 3.2 to
ConfigParser, and the old alias has been deprecated since.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Tue, 20 Dec 2022 05:38:36 +0000 (00:38 -0500)]
patman: fix pep8 warnings in settings module
Remove extraneous imports, variables and comply to PEP 8 maximum line
width, among other PEP 8 changes suggested by Pyflake.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:45 +0000 (17:32 -0500)]
patman: document default 'send' command
Document that this command is the default and what it's intended for.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:44 +0000 (17:32 -0500)]
patman: document how to run test suite via pytest
Pytest offers useful features such as selecting tests by means of a
regular expression, or running the pdb debugger upon encountering a
test failure.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:43 +0000 (17:32 -0500)]
patman: hide the 'test' command unless test data is available
Some tests would fail when the test data is not available, so it
doesn't make much sense to expose the action when patman is running
outside of the u-boot git checkout.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:42 +0000 (17:32 -0500)]
patman: add pytest configuration file
With this change, a user can run the patman test suite using Pytest
the same as when using 'patman test':
$ cd tools/patman && pytest
[...]
44 passed, 8 warnings in 8.87s
$ ./patman test
Ran 44 tests in 8.460s
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:41 +0000 (17:32 -0500)]
patman: rename main script to __main__.py
This allows running the package as a Python module, like e.g.:
$ python -m patman
It also prevents Pytest from attempting to parse main.py, which
would cause errors.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Fix up main.py in __init__.py:
Signed-off-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:40 +0000 (17:32 -0500)]
patman: invoke the checkpatch.pl script with '--u-boot' and '--strict'
This resolves 10 out of 11 test failures seen when running './patman
test' from the 'tools/patman' subdirectory. This was caused by the
.checkpatch.conf configuration file at the root of the project not
being picked up. Make the test suite of patman independent from it by
always invoking the checkpatch.pl script with the minimally required
arguments for the test suite to pass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:39 +0000 (17:32 -0500)]
patman: locate test data files via __file__ and pathlib
Previously it would rely on the executing script location, which could
break for example when running the tests via 'pytest'.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Mon, 19 Dec 2022 22:32:38 +0000 (17:32 -0500)]
patman: cosmetic: Fix PEP 8 warnings for the gitutil module.
This patch fixes all the PEP 8 warnings reported by Pyflake for the
gitutil module.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Maxim Cournoyer [Sat, 17 Dec 2022 01:45:29 +0000 (20:45 -0500)]
patman: locate README.rst via importlib
Rationale: this is more robust than assumptions about the file
hierarchy layout of the installation of patman, for example on non
file-hierarchy standard (FHS) systems such as Guix System or Nix OS.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Sat, 17 Dec 2022 01:45:28 +0000 (20:45 -0500)]
patman: fix installation of README.rst data file
This fixes a regression introduced in commit
74df491051d6 ("buildman:
Convert documentation to rST").
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Maxim Cournoyer [Sat, 17 Dec 2022 01:45:27 +0000 (20:45 -0500)]
patman: remove extraneous imports
* tools/patman/main.py: Remove extraneous imports and fix indentation.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@savoirfairelinux.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Yuepeng Xing [Fri, 2 Dec 2022 06:23:07 +0000 (14:23 +0800)]
test:dm:fix typo
Fix typos in the 'test/dm' directory.
Signed-off-by: Yuepeng Xing <xingyuepeng@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Sun, 27 Nov 2022 21:55:02 +0000 (16:55 -0500)]
patman: Switch to setuptools
distutils is about to meet its demise [1]. Switch to setuptools.
[1] https://peps.python.org/pep-0632/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sergiu Moga [Wed, 4 Jan 2023 14:03:18 +0000 (16:03 +0200)]
reset: at91: Add reset driver for basic assert/deassert operations
Add support for at91 reset controller's basic assert/deassert
operations. Since this driver conflicts with the
SYSRESET driver because they both bind to the same RSTC node,
implement a custom bind hook that would manually bind the
sysreset driver, if enabled, to the same RSTC DT node.
Furthermore, delete the no longer needed compatibles from the
SYSRESET driver and rename it to make sure than any possible
conflicts are avoided.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Tested-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cristian Birsan [Wed, 4 Jan 2023 14:03:17 +0000 (16:03 +0200)]
ARM: at91: add sama7 SFR definitions
Special Function Registers(SFR) definitions for SAMA7 product family.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Sergiu Moga [Wed, 4 Jan 2023 14:04:18 +0000 (16:04 +0200)]
ARM: dts: sama5d27_wlsom1_ek: Add pinctrl nodes for USB DT nodes
Add the pinctrl nodes required by the USB related DT nodes.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Sergiu Moga [Wed, 4 Jan 2023 14:04:17 +0000 (16:04 +0200)]
ARM: dts: sama5d2_icp: Add pinctrl nodes for USB related DT nodes
Add the pinctrl subnodes required by the USB related DT nodes.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Sergiu Moga [Wed, 4 Jan 2023 14:04:16 +0000 (16:04 +0200)]
ARM: dts: sama7g5ek: Add pinctrl, gpio and phy properties for USB
Add the required pinctrl, gpio and phy properties required by the
USB DT nodes of the sama7g5ek boards. Since these have not yet been
defined in upstream Linux, place them in the U-Boot specific DT file.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Sergiu Moga [Wed, 4 Jan 2023 14:04:15 +0000 (16:04 +0200)]
ARM: dts: sama7g5: Add USB and UTMI DT nodes
Define the USB and UTMI DT nodes for the sama7g5 SoC's. Since these have
not yet been defined in upstream Linux, place them in the U-Boot specific
DT file.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Sergiu Moga [Wed, 4 Jan 2023 14:04:14 +0000 (16:04 +0200)]
dt-bindings: clk: at91: Define additional UTMI related clocks
Add definitions for an additional main UTMI clock as well as its
respective subclocks.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Sergiu Moga [Wed, 4 Jan 2023 14:04:13 +0000 (16:04 +0200)]
dt-bindings: reset: add sama7g5 definitions
Upstream linux commit
5994f58977e0.
Add reset bindings for SAMA7G5. At the moment only USB PHYs are
included.
The three reset USB phy's have their ID's mapped from 4 to 6. There are
no USB phy's with ID's numbered from 0 to 3.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Sergiu Moga [Wed, 4 Jan 2023 14:04:12 +0000 (16:04 +0200)]
ARM: dts: sam9x60ek: Add pinctrl and gpio properties for USB
Add the required pinctrl and gpio properties required by the USB DT
nodes of the sam9x60ek boards.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Sergiu Moga [Wed, 4 Jan 2023 14:04:11 +0000 (16:04 +0200)]
ARM: dts: sam9x60_curiosity: Add pinctrl and gpio properties for USB
Add the required pinctrl and gpio properties needed by the USB DT nodes
of the sam9x60_curiosity boards.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>