Marc Kleine-Budde [Mon, 6 Jul 2020 14:34:36 +0000 (16:34 +0200)]
spi: spi-sun6i: sun6i_spi_transfer_one(): remove useless goto
This patch removes an useless goto at the end of
sun6i_spi_transfer_one().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-4-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 6 Jul 2020 14:34:35 +0000 (16:34 +0200)]
spi: spi-sun6i: sun6i_spi_transfer_one(): report effectivly used speed_hz of transfer
This patch implementes the reporting of the effectivly used speed_hz for the
transfer by setting tfr->effective_speed_hz.
See the following patch, which adds this feature to the SPI core for more
information:
5d7e2b5ed585 spi: core: allow reporting the effectivly used speed_hz for a transfer
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 6 Jul 2020 14:34:34 +0000 (16:34 +0200)]
spi: spi-sun6i: sun6i_spi_transfer_one(): fix setting of clock rate
A SPI transfer defines the _maximum_ speed of the SPI transfer. However the
driver doesn't take into account that the clock divider is always rounded down
(due to integer arithmetics). This results in a too high clock rate for the SPI
transfer.
E.g.: with a mclk_rate of 24 MHz and a SPI transfer speed of 10 MHz, the
original code calculates a reg of "0", which results in a effective divider of
"2" and a 12 MHz clock for the SPI transfer.
This patch fixes the issue by using DIV_ROUND_UP() instead of a plain
integer division.
While there simplify the divider calculation for the CDR1 case, use
order_base_2() instead of two ilog2() calculations.
Fixes:
3558fe900e8a ("spi: sunxi: Add Allwinner A31 SPI controller driver")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20200706143443.9855-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
leilk.liu [Wed, 1 Jul 2020 09:00:20 +0000 (17:00 +0800)]
spi: mediatek: use correct SPI_CFG2_REG MACRO
this patch use correct SPI_CFG2_REG offset.
Signed-off-by: leilk.liu <leilk.liu@mediatek.com>
Link: https://lore.kernel.org/r/20200701090020.7935-1-leilk.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jarkko Nikula [Thu, 25 Jun 2020 14:00:41 +0000 (17:00 +0300)]
spi: pxa2xx: Add support for Intel Tiger Lake PCH-H
Add Intel Tiger Lake PCH-H PCI IDs.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200625140041.745804-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Krzysztof Kozlowski [Mon, 22 Jun 2020 11:05:43 +0000 (13:05 +0200)]
spi: spi-fsl-dspi: Initialize completion before possible interrupt
The interrupt handler calls completion and is IRQ requested before the
completion is initialized. Logically it should be the other way.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-4-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Krzysztof Kozlowski [Mon, 22 Jun 2020 11:05:42 +0000 (13:05 +0200)]
spi: spi-fsl-dspi: Fix external abort on interrupt in resume or exit paths
If shared interrupt comes late, during probe error path or device remove
(could be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
dspi_interrupt() will access registers with the clock being disabled.
This leads to external abort on non-linefetch on Toradex Colibri VF50
module (with Vybrid VF5xx):
$ echo
4002d000.spi > /sys/devices/platform/soc/
40000000.bus/
4002d000.spi/driver/unbind
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8887f02c
Internal error: : 1008 [#1] ARM
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
(regmap_mmio_read32le)
(regmap_mmio_read)
(_regmap_bus_reg_read)
(_regmap_read)
(regmap_read)
(dspi_interrupt)
(free_irq)
(devm_irq_release)
(release_nodes)
(devres_release_all)
(device_release_driver_internal)
The resource-managed framework should not be used for shared interrupt
handling, because the interrupt handler might be called after releasing
other resources and disabling clocks.
Similar bug could happen during suspend - the shared interrupt handler
could be invoked after suspending the device. Each device sharing this
interrupt line should disable the IRQ during suspend so handler will be
invoked only in following cases:
1. None suspended,
2. All devices resumed.
Fixes:
349ad66c0ab0 ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Krzysztof Kozlowski [Mon, 22 Jun 2020 11:05:41 +0000 (13:05 +0200)]
spi: spi-fsl-dspi: Fix lockup if device is shutdown during SPI transfer
During shutdown, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
shutdown reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes:
dc234825997e ("spi: spi-fsl-dspi: Adding shutdown hook")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-2-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Krzysztof Kozlowski [Mon, 22 Jun 2020 11:05:40 +0000 (13:05 +0200)]
spi: spi-fsl-dspi: Fix lockup if device is removed during SPI transfer
During device removal, the driver should unregister the SPI controller
and stop the hardware. Otherwise the dspi_transfer_one_message() could
wait on completion infinitely.
Additionally, calling spi_unregister_controller() first in device
removal reverse-matches the probe function, where SPI controller is
registered at the end.
Fixes:
05209f457069 ("spi: fsl-dspi: add missing clk_disable_unprepare() in dspi_remove()")
Reported-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200622110543.5035-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhenzhong Duan [Thu, 18 Jun 2020 03:21:25 +0000 (11:21 +0800)]
spi: spidev: fix a potential use-after-free in spidev_release()
If an spi device is unbounded from the driver before the release
process, there will be an NULL pointer reference when it's
referenced in spi_slave_abort().
Fix it by checking it's already freed before reference.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Link: https://lore.kernel.org/r/20200618032125.4650-2-zhenzhong.duan@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhenzhong Duan [Thu, 18 Jun 2020 03:21:24 +0000 (11:21 +0800)]
spi: spidev: fix a race between spidev_release and spidev_remove
Imagine below scene, spidev is referenced after it's freed.
spidev_release() spidev_remove()
...
spin_lock_irq(&spidev->spi_lock);
spidev->spi = NULL;
spin_unlock_irq(&spidev->spi_lock);
mutex_lock(&device_list_lock);
dofree = (spidev->spi == NULL);
if (dofree)
kfree(spidev);
mutex_unlock(&device_list_lock);
mutex_lock(&device_list_lock);
list_del(&spidev->device_entry);
device_destroy(spidev_class, spidev->devt);
clear_bit(MINOR(spidev->devt), minors);
if (spidev->users == 0)
kfree(spidev);
mutex_unlock(&device_list_lock);
Fix it by resetting spidev->spi in device_list_lock's protection.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Link: https://lore.kernel.org/r/20200618032125.4650-1-zhenzhong.duan@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard [Tue, 16 Jun 2020 11:30:35 +0000 (13:30 +0200)]
spi: stm32-qspi: Fix error path in case of -EPROBE_DEFER
In case of -EPROBE_DEFER, stm32_qspi_release() was called
in any case which unregistered driver from pm_runtime framework
even if it has not been registered yet to it. This leads to:
stm32-qspi
58003000.spi: can't setup spi0.0, status -13
spi_master spi0: spi_device register error /soc/spi@
58003000/mx66l51235l@0
spi_master spi0: Failed to create SPI device for /soc/spi@
58003000/mx66l51235l@0
stm32-qspi
58003000.spi: can't setup spi0.1, status -13
spi_master spi0: spi_device register error /soc/spi@
58003000/mx66l51235l@1
spi_master spi0: Failed to create SPI device for /soc/spi@
58003000/mx66l51235l@1
On v5.7 kernel,this issue was not "visible", qspi driver was probed
successfully.
Fixes:
9d282c17b023 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200616113035.4514-1-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Sat, 13 Jun 2020 07:37:54 +0000 (09:37 +0200)]
spi: uapi: spidev: Use TABs for alignment
The UAPI <linux/spi/spidev.h> uses TABs for alignment.
Convert the recently introduced spaces to TABs to restore consistency.
Fixes:
7bb64402a092136 ("spi: tools: Add macro definitions to fix build errors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200613073755.15906-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Krzysztof Kozlowski [Wed, 10 Jun 2020 15:41:57 +0000 (17:41 +0200)]
spi: spi-fsl-dspi: Free DMA memory with matching function
Driver allocates DMA memory with dma_alloc_coherent() but frees it with
dma_unmap_single().
This causes DMA warning during system shutdown (with DMA debugging) on
Toradex Colibri VF50 module:
WARNING: CPU: 0 PID: 1 at ../kernel/dma/debug.c:1036 check_unmap+0x3fc/0xb04
DMA-API: fsl-edma
40098000.dma-controller: device driver frees DMA memory with wrong function
[device address=0x0000000087040000] [size=8 bytes] [mapped as coherent] [unmapped as single]
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(unwind_backtrace) from [<
8010bb34>] (show_stack+0x10/0x14)
(show_stack) from [<
8011ced8>] (__warn+0xf0/0x108)
(__warn) from [<
8011cf64>] (warn_slowpath_fmt+0x74/0xb8)
(warn_slowpath_fmt) from [<
8017d170>] (check_unmap+0x3fc/0xb04)
(check_unmap) from [<
8017d900>] (debug_dma_unmap_page+0x88/0x90)
(debug_dma_unmap_page) from [<
80601d68>] (dspi_release_dma+0x88/0x110)
(dspi_release_dma) from [<
80601e4c>] (dspi_shutdown+0x5c/0x80)
(dspi_shutdown) from [<
805845f8>] (device_shutdown+0x17c/0x220)
(device_shutdown) from [<
80143ef8>] (kernel_restart+0xc/0x50)
(kernel_restart) from [<
801441cc>] (__do_sys_reboot+0x18c/0x210)
(__do_sys_reboot) from [<
80100060>] (ret_fast_syscall+0x0/0x28)
DMA-API: Mapped at:
dma_alloc_attrs+0xa4/0x130
dspi_probe+0x568/0x7b4
platform_drv_probe+0x6c/0xa4
really_probe+0x208/0x348
driver_probe_device+0x5c/0xb4
Fixes:
90ba37033cb9 ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1591803717-11218-1-git-send-email-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qing Zhang [Thu, 11 Jun 2020 12:56:52 +0000 (20:56 +0800)]
spi: tools: Add macro definitions to fix build errors
Add SPI_TX_OCTAL and SPI_RX_OCTAL to fix the following build errors:
CC spidev_test.o
spidev_test.c: In function ‘transfer’:
spidev_test.c:131:13: error: ‘SPI_TX_OCTAL’ undeclared (first use in this function)
if (mode & SPI_TX_OCTAL)
^
spidev_test.c:131:13: note: each undeclared identifier is reported only once for each function it appears in
spidev_test.c:137:13: error: ‘SPI_RX_OCTAL’ undeclared (first use in this function)
if (mode & SPI_RX_OCTAL)
^
spidev_test.c: In function ‘parse_opts’:
spidev_test.c:290:12: error: ‘SPI_TX_OCTAL’ undeclared (first use in this function)
mode |= SPI_TX_OCTAL;
^
spidev_test.c:308:12: error: ‘SPI_RX_OCTAL’ undeclared (first use in this function)
mode |= SPI_RX_OCTAL;
^
LD spidev_test-in.o
ld: cannot find spidev_test.o: No such file or directory
Additionally, maybe SPI_CS_WORD and SPI_3WIRE_HIZ will be used in the future,
so add them too.
Fixes:
896fa735084e ("spi: spidev_test: Add support for Octal mode data transfers")
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1591880212-13479-2-git-send-email-zhangqing@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Qing Zhang [Thu, 11 Jun 2020 12:56:51 +0000 (20:56 +0800)]
spi: tools: Make default_tx/rx and input_tx static
Fix the following sparse warning:
./spidev_test.c:50:9: warning: symbol 'default_tx' was not declared. Should it be static?
./spidev_test.c:59:9: warning: symbol 'default_rx' was not declared. Should it be static?
./spidev_test.c:60:6: warning: symbol 'input_tx' was not declared. Should it be static?
Signed-off-by: Qing Zhang <zhangqing@loongson.cn>
Link: https://lore.kernel.org/r/1591880212-13479-1-git-send-email-zhangqing@loongson.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexander Stein [Tue, 9 Jun 2020 16:55:27 +0000 (18:55 +0200)]
spi: dt-bindings: amlogic, meson-gx-spicc: Fix schema for meson-g12a
spi@13000: clock-names: Additional items are not allowed ('pclk' was unexpected)
spi@13000: clock-names: ['core', 'pclk'] is too long
spi@13000: clocks: [[2, 23], [2, 258]] is too long
spi@15000: clock-names: Additional items are not allowed ('pclk' was unexpected)
spi@15000: clock-names: ['core', 'pclk'] is too long
spi@15000: clocks: [[2, 29], [2, 261]] is too long
Conditional schema properties don't overwrite others. Instead of
restrictions have to be validated. So general clock amount is 1-2 and
depending on the actual device type limit the mount to 1 or 2.
Signed-off-by: Alexander Stein <alexander.stein@mailbox.org>
Link: https://lore.kernel.org/r/20200609165527.55183-1-alexander.stein@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Mon, 8 Jun 2020 09:59:34 +0000 (11:59 +0200)]
spi: rspi: Use requested instead of maximum bit rate
Currently, the RSPI driver always tries to use the maximum configured
bit rate for communicating with a slave device, even if the transfer(s)
in the current message specify a lower rate.
Use the mininum rate specified in the message instead.
Rename rspi_data.max_speed_hz accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200608095940.30516-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Mon, 8 Jun 2020 10:00:49 +0000 (12:00 +0200)]
spi: spidev_test: Use %u to format unsigned numbers
Consistently use %u to format unsigned numbers.
For "bits" this doesn't matter that much, as it is "uint8_t".
However, "speed" is "uint32_t", so in case people use "-s -1" to force
the maximum, they would see:
max speed: -1 Hz (4294967 KHz)
While at it, use "k" (kilo) instead of "K" (kelvin) in "kHz".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200608100049.30648-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Lingling Xu [Tue, 2 Jun 2020 08:24:15 +0000 (16:24 +0800)]
spi: sprd: switch the sequence of setting WDG_LOAD_LOW and _HIGH
The watchdog counter consists of WDG_LOAD_LOW and WDG_LOAD_HIGH,
which would be loaded to watchdog counter once writing WDG_LOAD_LOW.
Fixes:
ac1775012058 ("spi: sprd: Add the support of restarting the system")
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200602082415.5848-1-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Angelo Dureghello [Fri, 29 May 2020 19:57:56 +0000 (21:57 +0200)]
spi: spi-fsl-dspi: fix native data copy
ColdFire is a big-endian cpu with a big-endian dspi hw module,
so, it uses native access, but memcpy breaks the endianness.
So, if i understand properly, by native copy we would mean
be(cpu)->be(dspi) or le(cpu)->le(dspi) accesses, so my fix
shouldn't break anything, but i couldn't test it on LS family,
so every test is really appreciated.
Fixes:
53fadb4d90c7 ("spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200529195756.184677-1-angelo.dureghello@timesys.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 18:25:43 +0000 (21:25 +0300)]
spi: Convert DW SPI binding to DT schema
Modern device tree bindings are supposed to be created as YAML-files
in accordance with dt-schema. This commit replaces two DW SPI legacy
bare text bindings with YAML file. As before the bindings file states
that the corresponding dts node is supposed to be compatible either
with generic DW APB SSI controller or with Microsemi/Amazon/Renesas/Intel
vendors-specific controllers, to have registers, interrupts and clocks
properties. Though in case of Microsemi version of the controller
there must be two registers resources specified. Properties like
clock-names, reg-io-width, cs-gpio, num-cs, DMA and slave device
sub-nodes are optional.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Link: https://lore.kernel.org/r/20200529182544.9807-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 29 May 2020 18:31:50 +0000 (21:31 +0300)]
spi: dw: Refactor mid_spi_dma_setup() to separate DMA and IRQ config
It's better to understand what bits are set for DMA and for IRQ handling
in mid_spi_dma_setup() if they are grouped accordingly. Thus,
refactor mid_spi_dma_setup() to separate DMA and IRQ configuration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 29 May 2020 18:31:49 +0000 (21:31 +0300)]
spi: dw: Make DMA request line assignments explicit for Intel Medfield
The
2afccbd283ae ("spi: dw: Discard static DW DMA slave structures")
did a clean up of global variables, which is fine, but messed up with
the carefully provided information in the custom DMA slave structures.
There reader can find an assignment of the DMA request lines in use.
Partially revert the above mentioned commit to restore readability
and maintainability of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200529183150.44149-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 29 May 2020 17:48:46 +0000 (18:48 +0100)]
spi: bcm2835: Remove shared interrupt support
This reverts commit
ecfbd3cf3b8b since Lukas Wunner noticed that we
start operating on the hardware before we check to see if this is a
spurious interrupt.
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 29 May 2020 16:49:56 +0000 (17:49 +0100)]
Merge series "spi: dw: Add generic DW DMA controller support" from Serge Semin <Sergey.Semin@baikalelectronics.ru>:
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit:
fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru
Changelog v4:
- Get back ndelay() method to wait for an SPI transfer completion.
spi_delay_exec() isn't suitable for the atomic context.
Link: https://lore.kernel.org/linux-spi/20200522000806.7381-1-Sergey.Semin@baikalelectronics.ru
Changelog v5:
- Refactor the Tx/Rx DMA-based SPI transfers wait methods.
- Add a new patch "spi: dw: Set xfer effective_speed_hz".
- Add a new patch "spi: dw: Return any value retrieved from the
dma_transfer callback" as a preparation patch before implementing
the local DMA, Tx SPI and Rx SPI transfers wait methods.
- Add a new patch "spi: dw: Locally wait for the DMA transactions
completion", which provides a local DMA transaction complete
method
- Create a dedicated patch which adds the Rx-done wait method:
"spi: dw: Add SPI Rx-done wait method to DMA-based transfer".
- Add more detailed description of the problems the Tx/Rx-wait
methods-related patches fix.
- Wait for the SPI Tx and Rx transfers being finished in the
mid_spi_dma_transfer() method executed in the task context.
- Use spi_delay_exec() to wait for the SPI Tx/Rx completion, since now
the driver calls the wait methods in the kernel thread context.
- Use SPI_DELAY_UNIT_SCK spi_delay unit for Tx-wait delay, since SPI
xfer's are now have the effective_speed_hz initialized.
- Rx-wait for a delay correlated with the APB/SSI synchronous clock
rate instead of using the SPI bus clock rate.
Link: https://lore.kernel.org/linux-spi/20200529035915.20790-1-Sergey.Semin@baikalelectronics.ru
Changelog v6:
- Provide a more detailed description of the patch:
2901db35bea1 ("spi: dw: Locally wait for the DMA transfers completion")
- Calculate the Rx delay with better accuracy by moving 4-multiplication
to the head of the formulae:
ns = 4U * NSEC_PER_SEC / dws->max_freq * nents.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (16):
spi: dw: Set xfer effective_speed_hz
spi: dw: Return any value retrieved from the dma_transfer callback
spi: dw: Locally wait for the DMA transfers completion
spi: dw: Add SPI Tx-done wait method to DMA-based transfer
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Fix Rx-only DMA transfers
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 44 --
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++
.../devicetree/bindings/spi/spi-dw.txt | 24 -
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 5 +-
drivers/spi/{spi-dw.c => spi-dw-core.c} | 95 ++--
drivers/spi/spi-dw-dma.c | 482 ++++++++++++++++++
drivers/spi/spi-dw-mid.c | 382 --------------
drivers/spi/spi-dw-mmio.c | 4 +
drivers/spi/spi-dw-pci.c | 50 +-
drivers/spi/spi-dw.h | 20 +-
11 files changed, 719 insertions(+), 529 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw.c => spi-dw-core.c} (82%)
create mode 100644 drivers/spi/spi-dw-dma.c
delete mode 100644 drivers/spi/spi-dw-mid.c
--
2.26.2
Dinh Nguyen [Fri, 29 May 2020 15:58:06 +0000 (10:58 -0500)]
dt-bindings: snps,dw-apb-ssi: add optional reset property
Add optional reset property.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200529155806.16758-2-dinguyen@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Dinh Nguyen [Fri, 29 May 2020 15:58:05 +0000 (10:58 -0500)]
spi: dw: add reset control
Add mechanism to get the reset control and deassert it in order to bring
the IP out of reset.
Signed-off-by: Liang Jin J <liang.j.jin@ericsson.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200529155806.16758-1-dinguyen@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Sperl [Thu, 28 May 2020 18:58:04 +0000 (20:58 +0200)]
spi: bcm2835: Enable shared interrupt support
bcm2711, Rasberry Pi 4's SoC, shares one interrupt for multiple
instances of the bcm2835 SPI controller. So this enables shared
interrupt support for them.
The early bail out in the interrupt routine avoids messing with buffers
of transfers being done by other means. Otherwise, the driver can handle
receiving interrupts asserted by other controllers during an IRQ based
transfer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200528185805.28991-1-nsaenzjulienne@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Florian Fainelli [Thu, 28 May 2020 19:06:05 +0000 (12:06 -0700)]
spi: bcm2835: Implement shutdown callback
Make sure we clear the FIFOs, stop the block, disable the clock and
release the DMA channel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200528190605.24850-1-f.fainelli@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:12:04 +0000 (16:12 +0300)]
spi: dw: Use regset32 DebugFS method to create regdump file
DebugFS kernel interface provides a dedicated method to create the
registers dump file. Use it instead of creating a generic DebugFS
file with manually written read callback function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:12:03 +0000 (16:12 +0300)]
spi: dw: Add DMA support to the DW SPI MMIO driver
Since the common code in the spi-dw-dma.c driver is ready to be used
by the MMIO driver and now provides a method to generically (on any
DT or ACPI-based platforms) retrieve the Tx/Rx DMA channel handlers,
we can use it and a set of the common DW SPI DMA callbacks to enable
DMA at least for generic "snps,dw-apb-ssi" and "snps,dwc-ssi-1.01a"
devices.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-15-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:12:02 +0000 (16:12 +0300)]
spi: dw: Cleanup generic DW DMA code namings
Since from now the former Intel MID platform layer is used as a generic
DW SPI DMA module, let's alter the internal methods naming to be
DMA-related instead of having the "mid_" prefix.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-14-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:12:01 +0000 (16:12 +0300)]
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
Seeing all of the DW SPI driver components like DW SPI DMA/PCI/MMIO
depend on the DW SPI core code it's better to use the if-endif
conditional kernel config statement to signify that common dependency.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-13-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:12:00 +0000 (16:12 +0300)]
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
Since there is a generic method available to initialize the DW SPI DMA
interface on any DT and ACPI-based platforms, which in general can be
designed with not only DW DMAC but with any DMA engine on board, we can
freely remove the CONFIG_DW_DMAC_PCI config from dependency list of
CONFIG_SPI_DW_DMA. Especially seeing that we don't use anything DW DMAC
specific in the new driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:59 +0000 (16:11 +0300)]
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:58 +0000 (16:11 +0300)]
spi: dw: Add core suffix to the DW APB SSI core source file
Generic DMA support is going to be part of the DW APB SSI core object.
In order to preserve the kernel loadable module name as spi-dw.ko, let's
add the "-core" suffix to the object with generic DW APB SSI code and
build it into the target spi-dw.ko driver.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:57 +0000 (16:11 +0300)]
spi: dw: Fix Rx-only DMA transfers
Tx-only DMA transfers are working perfectly fine since in this case
the code just ignores the Rx FIFO overflow interrupts. But it turns
out the SPI Rx-only transfers are broken since nothing pushing any
data to the shift registers, so the Rx FIFO is left empty and the
SPI core subsystems just returns a timeout error. Since DW DMAC
driver doesn't support something like cyclic write operations of
a single byte to a device register, the only way to support the
Rx-only SPI transfers is to fake it by using a dummy Tx-buffer.
This is what we intend to fix in this commit by setting the
SPI_CONTROLLER_MUST_TX flag for DMA-capable platform.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:56 +0000 (16:11 +0300)]
spi: dw: Use DMA max burst to set the request thresholds
Each channel of DMA controller may have a limited length of burst
transaction (number of IO operations performed at ones in a single
DMA client request). This parameter can be used to setup the most
optimal DMA Tx/Rx data level values. In order to avoid the Tx buffer
overrun we can set the DMA Tx level to be of FIFO depth minus the
maximum burst transactions length. To prevent the Rx buffer underflow
the DMA Rx level should be set to the maximum burst transactions length.
This commit setups the DMA channels and the DW SPI DMA Tx/Rx levels
in accordance with these rules.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:55 +0000 (16:11 +0300)]
spi: dw: Parameterize the DMA Rx/Tx burst length
It isn't good to have numeric literals in the code especially if there
are multiple of them and they are related. Let's replace the Tx and Rx
burst level literals with the corresponding constants.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:54 +0000 (16:11 +0300)]
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
Having any data left in the Rx FIFO after the DMA engine claimed it has
finished all DMA transactions is an abnormal situation, since the DW SPI
controller driver expects to have all the data being fetched and placed
into the SPI Rx buffer at that moment. In case if that has happened we
hopefully assume that the DMA engine may still be doing the data fetching,
thus we give it sometime to finish. If after a short period of time the
data is still left in the Rx FIFO, the driver will give up waiting and
return an error indicating that the SPI controller/DMA engine must have
hung up or failed at some point of doing their duties.
Fixes:
7063c0d942a1 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:53 +0000 (16:11 +0300)]
spi: dw: Add SPI Tx-done wait method to DMA-based transfer
Since DMA transfers are performed asynchronously with actual SPI bus
transfers, then even if DMA transactions are finished it doesn't mean
all data is actually pushed to the SPI bus. Some data might still be
in the controller FIFO. This is specifically true for Tx-only transfers.
In this case if the next SPI transfer is recharged while a tail of the
previous one is still in FIFO, we'll loose that tail data. In order to
fix that problem let's add the wait procedure of the Tx SPI transfer
completion after the DMA transactions are finished.
Fixes:
7063c0d942a1 ("spi/dw_spi: add DMA support")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:52 +0000 (16:11 +0300)]
spi: dw: Locally wait for the DMA transfers completion
In general each DMA-based SPI transfer can be split up into two stages:
DMA data transmission/reception and SPI-bus transmission/reception. DMA
asynchronous transactions completion can be tracked by means of the
DMA async Tx-descriptor completion callback. But that callback being
called indicates that the DMA transfer has been finished, it doesn't
mean that SPI data transmission is also done. Moreover in fact it isn't
for at least Tx-only SPI transfers. Upon DMA transfer completion some
data is left in the Tx FIFO and being pushed out by the SPI controller.
So in order to make sure that an SPI transfer is completely pushed to the
SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus
transmission/reception are finished. Note if there is a way to
asynchronously track the former event by means of the DMA async Tx
callback, there isn't easy one for the later (IRQ-based solution won't
work since SPI controller doesn't notify about Rx FIFO being empty).
The DMA transfer completion callback isn't suitable to wait for the
SPI controller activity finish either. The callback might (in case of DW
DMAC it will) be called in the tasklet context. Waiting for the SPI
controller to complete the transfer might take a considerable amount of
time since SPI-bus might be pretty slow. In this case delaying the
execution in the tasklet atomic context might cause significant system
performance drop.
So to speak the best option we've got to solve the problem is to
consequently wait for both stages being finished in the locally
implemented SPI transfer execution procedure even if it costs us of the
local wait-function re-implementation. In this case we don't need to use
the SPI-core transfer-wait functionality, but we'll make sure that
all DMA and SPI-bus transactions are completely finished before the
SPI-core transfer_one callback returns. In this commit we provide an
implementation of the DMA-transfers completion wait functionality.
The DW APB SSI DMA-specific SPI transfer_one function waits for both
Tx and Rx DMA transfers being finished, and only then exits with zero
returned signalling to the SPI core that the SPI transfer is finished.
This implementation is fully equivalent to the currently used
DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception
wait methods will be added in the follow-up commits.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:51 +0000 (16:11 +0300)]
spi: dw: Return any value retrieved from the dma_transfer callback
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 29 May 2020 13:11:50 +0000 (16:11 +0300)]
spi: dw: Set xfer effective_speed_hz
Seeing DW APB SSI controller doesn't support setting the exactly
requested SPI bus frequency, but only a rounded frequency determined
by means of the odd-numbered half-worded reference clock divider,
it would be good to tune the SPI core up and initialize the current
transfer effective_speed_hz. By doing so the core will be able to
execute the xfer-related delays with better accuracy.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Thu, 28 May 2020 13:01:17 +0000 (14:01 +0100)]
Merge series "add ecspi ERR009165 for i.mx6/7 soc family" from Robin Gong <yibin.gong@nxp.com>:
There is ecspi ERR009165 on i.mx6/7 soc family, which cause FIFO
transfer to be send twice in DMA mode. Please get more information from:
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf. The workaround is adding
new sdma ram script which works in XCH mode as PIO inside sdma instead
of SMC mode, meanwhile, 'TX_THRESHOLD' should be 0. The issue should be
exist on all legacy i.mx6/7 soc family before i.mx6ul.
NXP fix this design issue from i.mx6ul, so newer chips including i.mx6ul/
6ull/6sll do not need this workaroud anymore. All other i.mx6/7/8 chips
still need this workaroud. This patch set add new 'fsl,imx6ul-ecspi'
for ecspi driver and 'ecspi_fixed' in sdma driver to choose if need errata
or not.
The first two reverted patches should be the same issue, though, it
seems 'fixed' by changing to other shp script. Hope Sean or Sascha could
have the chance to test this patch set if could fix their issues.
Besides, enable sdma support for i.mx8mm/8mq and fix ecspi1 not work
on i.mx8mm because the event id is zero.
PS:
Please get sdma firmware from below linux-firmware and copy it to your
local rootfs /lib/firmware/imx/sdma.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/imx/sdma
v2:
1.Add commit log for reverted patches.
2.Add comment for 'ecspi_fixed' in sdma driver.
3.Add 'fsl,imx6sll-ecspi' compatible instead of 'fsl,imx6ul-ecspi'
rather than remove.
v3:
1.Confirm with design team make sure ERR009165 fixed on i.mx6ul/i.mx6ull
/i.mx6sll, not fixed on i.mx8m/8mm and other i.mx6/7 legacy chips.
Correct dts related dts patch in v2.
2.Clean eratta information in binding doc and new 'tx_glitch_fixed' flag
in spi-imx driver to state ERR009165 fixed or not.
3.Enlarge burst size to fifo size for tx since tx_wml set to 0 in the
errata workaroud, thus improve performance as possible.
v4:
1.Add Ack tag from Mark and Vinod
2.Remove checking 'event_id1' zero as 'event_id0'.
v5:
1.Add the last patch for compatible with the current uart driver which
using rom script, so both uart ram script and rom script supported
in latest firmware, by default uart rom script used. UART driver
will be broken without this patch.
v6:
1.Resend after rebase the latest next branch.
2.Remove below No.13~No.15 patches of v5 because they were mergered.
ARM: dts: imx6ul: add dma support on ecspi
ARM: dts: imx6sll: correct sdma compatible
arm64: defconfig: Enable SDMA on i.mx8mq/8mm
3.Revert "dmaengine: imx-sdma: fix context cache" since
'context_loaded' removed.
v7:
1.Put the last patch 13/13 'Revert "dmaengine: imx-sdma: fix context
cache"' to the ahead of 03/13 'Revert "dmaengine: imx-sdma: refine
to load context only once" so that no building waring during comes out
during bisect.
2.Address Sascha's comments, including eliminating any i.mx6sx in this
series, adding new 'is_imx6ul_ecspi()' instead imx in imx51 and taking
care SMC bit for PIO.
3.Add back missing 'Reviewed-by' tag on 08/15(v5):09/13(v7)
'spi: imx: add new i.mx6ul compatible name in binding doc'
v8:
1.remove 0003-Revert-dmaengine-imx-sdma-fix-context-cache.patch and merge
it into 04/13 of v7
2.add 0005-spi-imx-fallback-to-PIO-if-dma-setup-failure.patch for no any
ecspi function broken even if sdma firmware not updated.
3.merge 'tx.dst_maxburst' changes in the two continous patches into one
patch to avoid confusion.
4.fix typo 'duplicated'.
Robin Gong (13):
Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core"
Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores"
Revert "dmaengine: imx-sdma: refine to load context only once"
dmaengine: imx-sdma: remove duplicated sdma_load_context
spi: imx: fallback to PIO if dma setup failure
dmaengine: imx-sdma: add mcu_2_ecspi script
spi: imx: fix ERR009165
spi: imx: remove ERR009165 workaround on i.mx6ul
spi: imx: add new i.mx6ul compatible name in binding doc
dmaengine: imx-sdma: remove ERR009165 on i.mx6ul
dma: imx-sdma: add i.mx6ul compatible name
dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm
dmaengine: imx-sdma: add uart rom script
.../devicetree/bindings/dma/fsl-imx-sdma.txt | 1 +
.../devicetree/bindings/spi/fsl-imx-cspi.txt | 1 +
arch/arm/boot/dts/imx6q.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl.dtsi | 8 +-
drivers/dma/imx-sdma.c | 67 ++++++++++------
drivers/spi/spi-imx.c | 92 +++++++++++++++++++---
include/linux/platform_data/dma-imx-sdma.h | 8 +-
7 files changed, 135 insertions(+), 44 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Dinghao Liu [Sat, 23 May 2020 12:47:58 +0000 (20:47 +0800)]
spi: tegra20-sflash: Fix runtime PM imbalance on error
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523124758.28604-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Dinghao Liu [Sat, 23 May 2020 12:29:09 +0000 (20:29 +0800)]
spi: tegra20-slink: Fix runtime PM imbalance on error
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523122909.25247-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Dinghao Liu [Sat, 23 May 2020 12:57:04 +0000 (20:57 +0800)]
spi: tegra114: Fix runtime PM imbalance on error
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523125704.30300-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Robin Gong [Wed, 20 May 2020 20:34:17 +0000 (04:34 +0800)]
spi: imx: fallback to PIO if dma setup failure
Fallback to PIO in case dma setup failed. For example, sdma firmware not
updated but ERR009165 workaroud added in kernel.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/1590006865-20900-6-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dinghao Liu [Sat, 23 May 2020 13:38:59 +0000 (21:38 +0800)]
spi: spi-fsl-lpspi: Fix runtime PM imbalance on error
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200523133859.5625-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Mon, 25 May 2020 13:31:20 +0000 (14:31 +0100)]
spi: Remove note about transfer limit for spi_write_then_read()
Originally spi_write_then_read() used a fixed statically allocated
buffer which limited the maximum message size it could handle. This
restriction was removed a while ago so that we could dynamically
allocate a buffer if required but the kerneldoc was not updated to
reflect this, do so.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200525133120.57273-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dillon min [Mon, 25 May 2020 03:45:48 +0000 (11:45 +0800)]
spi: flags 'SPI_CONTROLLER_MUST_RX' and 'SPI_CONTROLLER_MUST_TX' can't be coexit with 'SPI_3WIRE' mode
since chip spi driver need get the transfer direction by 'tx_buf' and
'rx_buf' of 'struct spi_transfer' in 'SPI_3WIRE' mode.
so, we need bypass 'SPI_CONTROLLER_MUST_RX' and 'SPI_CONTROLLER_MUST_TX'
feature in 'SPI_3WIRE' mode
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Link: https://lore.kernel.org/r/1590378348-8115-9-git-send-email-dillon.minfei@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dillon min [Mon, 25 May 2020 03:45:47 +0000 (11:45 +0800)]
spi: stm32: Add 'SPI_SIMPLEX_RX', 'SPI_3WIRE_RX' support for stm32f4
in l3gd20 driver startup, there is a setup failed error return from
stm32 spi driver
"
[ 2.687630] st-gyro-spi spi0.0: supply vdd not found, using dummy
regulator
[ 2.696869] st-gyro-spi spi0.0: supply vddio not found, using dummy
regulator
[ 2.706707] spi_stm32
40015000.spi: SPI transfer setup failed
[ 2.713741] st-gyro-spi spi0.0: SPI transfer failed: -22
[ 2.721096] spi_master spi0: failed to transfer one message from queue
[ 2.729268] iio iio:device0: failed to read Who-Am-I register.
[ 2.737504] st-gyro-spi: probe of spi0.0 failed with error -22
"
after debug into spi-stm32 driver, st-gyro-spi split two steps to read
l3gd20 id
first: send command to l3gd20 with read id command in tx_buf, rx_buf
is null.
second: read id with tx_buf is null, rx_buf not null.
so, for second step, stm32 driver recongise this process as 'SPI_SIMPLE_RX'
from stm32_spi_communication_type(), but there is no related process for this
type in stm32f4_spi_set_mode(), then we get error from
stm32_spi_transfer_one_setup().
we can use two method to fix this bug.
1, use stm32 spi's "In unidirectional receive-only mode (BIDIMODE=0 and
RXONLY=1)". but as our code running in sdram, the read latency is too large
to get so many receive overrun error in interrupts handler.
2, use stm32 spi's "In full-duplex (BIDIMODE=0 and RXONLY=0)", as tx_buf is
null, so add flag 'SPI_MASTER_MUST_TX' to spi master.
Change since V4:
1 remove dummy data sent out by stm32 spi driver
2 add flag 'SPI_MASTER_MUST_TX' to spi master
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Link: https://lore.kernel.org/r/1590378348-8115-8-git-send-email-dillon.minfei@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 22 May 2020 15:50:05 +0000 (16:50 +0100)]
spi: Make spi_delay_exec() warn if called from atomic context
If the delay used is long enough the spi_delay_exec() will use a sleeping
function to implement it. Add a might_sleep() here to help avoid callers
using this from an atomic context and running into problems at runtime on
other systems.
Suggested-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200522155005.46099-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 22 May 2020 13:13:18 +0000 (14:13 +0100)]
Merge series "spi: dw: Add generic DW DMA controller support" from Serge Semin <Sergey.Semin@baikalelectronics.ru>:
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit:
fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200521012206.14472-1-Sergey.Semin@baikalelectronics.ru
Changelog v4:
- Get back ndelay() method to wait for an SPI transfer completion.
spi_delay_exec() isn't suitable for the atomic context.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Serge Semin (16):
spi: dw: Add Tx/Rx finish wait methods to the MID DMA
spi: dw: Enable interrupts in accordance with DMA xfer mode
spi: dw: Discard static DW DMA slave structures
spi: dw: Discard unused void priv pointer
spi: dw: Discard dma_width member of the dw_spi structure
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Fix Rx-only DMA transfers
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 44 ---
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++++++
.../devicetree/bindings/spi/spi-dw.txt | 24 --
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 5 +-
drivers/spi/{spi-dw.c => spi-dw-core.c} | 88 ++----
drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} | 261 ++++++++++--------
drivers/spi/spi-dw-mmio.c | 4 +
drivers/spi/spi-dw-pci.c | 50 +++-
drivers/spi/spi-dw.h | 33 ++-
10 files changed, 392 insertions(+), 259 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw.c => spi-dw-core.c} (82%)
rename drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} (55%)
--
2.25.1
Christopher Hill [Thu, 21 May 2020 18:36:31 +0000 (14:36 -0400)]
spi: rb4xx: add corresponding device tree documentation
This patch adds the correcsponding MikroTik vendor and device tree
documentation
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Link: https://lore.kernel.org/r/20200521183631.37806-3-ch6574@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christopher Hill [Thu, 21 May 2020 18:36:30 +0000 (14:36 -0400)]
spi: rb4xx: update driver to be device tree aware
This patch updates the spi driver spi-rb4xx.c to be device tree aware
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Link: https://lore.kernel.org/r/20200521183631.37806-2-ch6574@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christopher Hill [Thu, 21 May 2020 18:36:29 +0000 (14:36 -0400)]
spi: rb4xx: null pointer bug fix
This patch fixes a null pointer bug in the spi driver spi-rb4xx.c by
moving the private data initialization to earlier in probe
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Link: https://lore.kernel.org/r/20200521183631.37806-1-ch6574@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 22 May 2020 00:07:54 +0000 (03:07 +0300)]
spi: dw: Discard dma_width member of the dw_spi structure
This member has exactly the same value as n_bytes of the DW SPI private
data object, it's calculated at the same point of the transfer method,
n_bytes isn't changed during the whole transfer, and they even serve for
the same purpose - keep number of bytes per transfer word, though the
dma_width is used only to calculate the DMA source/destination addresses
width, which n_bytes could be also utilized for. Taking all of these
into account let's replace the dma_width member usage with n_bytes one
and remove the former.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 22 May 2020 00:07:53 +0000 (03:07 +0300)]
spi: dw: Discard unused void priv pointer
Seeing the "void *priv" member of the dw_spi data structure is unused
let's remove it. The glue-layers can embed the DW APB SSI controller
descriptor into their private data object. MMIO driver for instance
already utilizes that design pattern.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 22 May 2020 00:07:52 +0000 (03:07 +0300)]
spi: dw: Discard static DW DMA slave structures
Having them declared is redundant since each struct dw_dma_chan has
the same structure embedded and the structure from the passed dma_chan
private pointer will be copied there as a result of the next calls
chain:
dma_request_channel() -> find_candidate() -> dma_chan_get() ->
device_alloc_chan_resources() = dwc_alloc_chan_resources() ->
dw_dma_filter().
So just remove the static dw_dma_chan structures and use a locally
declared data instance with dst_id/src_id set to the same values as
the static copies used to have.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 22 May 2020 00:07:51 +0000 (03:07 +0300)]
spi: dw: Enable interrupts in accordance with DMA xfer mode
It's pointless to track the Tx overrun interrupts if Rx-only SPI
transfer is issued. Similarly there is no need in handling the Rx
overrun/underrun interrupts if Tx-only SPI transfer is executed.
So lets unmask the interrupts only if corresponding SPI
transactions are implied.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200522000806.7381-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Lukas Wunner [Fri, 15 May 2020 15:58:04 +0000 (17:58 +0200)]
spi: bcm2835: Tear down DMA before turning off SPI controller
On unbind of the BCM2835 SPI driver, the SPI controller is disabled
first and the DMA channels are terminated and torn down afterwards.
This seems backwards: In the theoretical case that DMA is active,
it might try to fill the SPI FIFOs even after the controller has
been disabled.
Reverse the order, thereby mirroring what's done on ->probe().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/ac79f1e3d6fd9a1f5e0cb4008c43b98ea70be3c2.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 20 May 2020 16:55:07 +0000 (17:55 +0100)]
Merge branch 'for-5.7' of https://git./linux/kernel/git/broonie/spi into spi-5.8
Lukas Wunner [Fri, 15 May 2020 15:58:03 +0000 (17:58 +0200)]
spi: bcm2835aux: Fix controller unregister order
The BCM2835aux SPI driver uses devm_spi_register_master() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835aux_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835aux_spi_remove() turns off the SPI
controller, including its interrupts and clock. The SPI controller
is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_master() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_master(). Note that the
struct spi_master as well as the driver-private data are not freed until
after bcm2835aux_spi_remove() has finished, so accessing them is safe.
Fixes:
1ea29b39f4c8 ("spi: bcm2835aux: add bcm2835 auxiliary spi device driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.4+
Cc: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/32f27f4d8242e4d75f9a53f7e8f1f77483b08669.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Lukas Wunner [Fri, 15 May 2020 15:58:02 +0000 (17:58 +0200)]
spi: bcm2835: Fix controller unregister order
The BCM2835 SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835_spi_remove() tears down the DMA
channels and turns off the SPI controller, including its interrupts
and clock. The SPI controller is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_controller(). Note that
the struct spi_controller as well as the driver-private data are not
freed until after bcm2835_spi_remove() has finished, so accessing them
is safe.
Fixes:
247263dba208 ("spi: bcm2835: use devm_spi_register_master()")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Link: https://lore.kernel.org/r/2397dd70cdbe95e0bc4da2b9fca0f31cb94e5aed.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Lukas Wunner [Fri, 15 May 2020 15:58:01 +0000 (17:58 +0200)]
spi: Fix controller unregister order
When an SPI controller unregisters, it unbinds all its slave devices.
For this, their drivers may need to access the SPI bus, e.g. to quiesce
interrupts.
However since commit
ffbbdd21329f ("spi: create a message queueing
infrastructure"), spi_destroy_queue() is executed before unbinding the
slaves. It sets ctlr->running = false, thereby preventing SPI bus
access and causing unbinding of slave devices to fail.
Fix by unbinding slaves before calling spi_destroy_queue().
Fixes:
ffbbdd21329f ("spi: create a message queueing infrastructure")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.4+
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/8aaf9d44c153fe233b17bc2dec4eb679898d7e7b.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Kangmin Park [Tue, 19 May 2020 07:32:21 +0000 (16:32 +0900)]
spi: ti_qspi: fix unit address
Fix unit address to match the first address specified in the reg
property of the node in example.
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Link: https://lore.kernel.org/r/1589873541-5587-1-git-send-email-l4stpr0gr4m@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 15 May 2020 10:47:40 +0000 (13:47 +0300)]
spi: dw: Add Tx/Rx DMA properties
Since commit
22d48ad7bfac ("spi: dw: Add Elkhart Lake PSE DMA support")
the spi-dw-mid.c module supports a platform DMA engine handling the DW APB
SSI controller requests. Lets alter the DW SPI bindings file to accept the
Rx and Tx DMA line specifiers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Allison Randal <allison@lohutok.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Gareth Williams <gareth.williams.jx@renesas.com>
Cc: linux-mips@vger.kernel.org
Link: https://lore.kernel.org/r/20200515104758.6934-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 15 May 2020 17:50:07 +0000 (18:50 +0100)]
Merge series "spi: dw: Add generic DW DMA controller support" from Serge Semin <Sergey.Semin@baikalelectronics.ru>:
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit:
fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Maxim Kaurkin <Maxim.Kaurkin@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Ekaterina Skachko <Ekaterina.Skachko@baikalelectronics.ru>
Cc: Vadim Vlasov <V.Vlasov@baikalelectronics.ru>
Cc: Alexey Kolotnikov <Alexey.Kolotnikov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Allison Randal <allison@lohutok.net>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Gareth Williams <gareth.williams.jx@renesas.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
---
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Serge Semin (19):
dt-bindings: spi: dw: Add Tx/Rx DMA properties
spi: dw: Add Tx/Rx finish wait methods to the MID DMA
spi: dw: Clear DMAC register when done or stopped
spi: dw: Fix native CS being unset
spi: dw: Enable interrupts in accordance with DMA xfer mode
spi: dw: Discard static DW DMA slave structures
spi: dw: Discard unused void priv pointer
spi: dw: Discard dma_width member of the dw_spi structure
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Initialize paddr in DW SPI MMIO private data
spi: dw: Fix Rx-only DMA transfers
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Use regset32 DebugFS method to create regdump file
dt-bindings: spi: Convert DW SPI binding to DT schema
.../bindings/spi/snps,dw-apb-ssi.txt | 42 ---
.../bindings/spi/snps,dw-apb-ssi.yaml | 127 +++++++++
.../devicetree/bindings/spi/spi-dw.txt | 24 --
drivers/spi/Kconfig | 15 +-
drivers/spi/Makefile | 7 +-
drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} | 257 ++++++++++--------
drivers/spi/spi-dw-mmio.c | 9 +-
drivers/spi/spi-dw-pci.c | 50 +++-
drivers/spi/spi-dw.c | 98 +++----
drivers/spi/spi-dw.h | 33 ++-
10 files changed, 405 insertions(+), 257 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt
create mode 100644 Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-dw.txt
rename drivers/spi/{spi-dw-mid.c => spi-dw-dma.c} (53%)
--
2.25.1
Chris Ruehl [Mon, 11 May 2020 08:30:22 +0000 (16:30 +0800)]
spi: spi-rockchip: use num-cs property and ctlr->enable_gpiods
The original implementation set num_chipselect to ROCKCHIP_SPI_MAX_CS_NUM (2)
which seems wrong here. spi0 has 2 native cs, all others just one. With
enable and use of cs_gpiods / GPIO CS, its correct to set the num_chipselect
from the num-cs property and set max_native_cs with the define.
If num-cs is missing the default set to num_chipselect = 1.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-4-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
Chris Ruehl [Mon, 11 May 2020 08:30:21 +0000 (16:30 +0800)]
spi: spi-rockchip: add support for spi slave mode
Add support for spi slave mode in spi-rockchip. The register map has an entry
for it. If spi-slave is set in dts, set this corresponding bit and add to
mode_bits the SPI_NO_CS, allow slave mode without explicit CS use.
Slave abort function had been added.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-3-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
Chris Ruehl [Mon, 11 May 2020 08:30:20 +0000 (16:30 +0800)]
spi: spi-rockchip: cleanup use struct spi_controller
Cleanup, move from the compatibily layer struct spi_master over
to struct spi_controller, and rename the related function calls.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20200511083022.23678-2-chris.ruehl@gtsys.com.hk
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 15 May 2020 10:47:42 +0000 (13:47 +0300)]
spi: dw: Clear DMAC register when done or stopped
If DMAC register is left uncleared any further DMAless transfers
may cause the DMAC hardware handshaking interface getting activated.
So the next DMA-based Rx/Tx transaction will be started right
after the dma_async_issue_pending() method is invoked even if no
DMATDLR/DMARDLR conditions are met. This at the same time may cause
the Tx/Rx FIFO buffers underrun/overrun. In order to fix this we
must clear DMAC register after a current DMA-based transaction is
finished.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200515104758.6934-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 15 May 2020 10:47:50 +0000 (13:47 +0300)]
spi: dw: Initialize paddr in DW SPI MMIO private data
This field is used only for the DW SPI DMA code initialization, that's
why there were no problems with it being uninitialized in Dw SPI MMIO
driver. Since in a further patch we are going to introduce the DW SPI DMA
support in the MMIO version of the driver, lets set the field with the
physical address of the DW SPI controller registers region.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200515104758.6934-12-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Serge Semin [Fri, 15 May 2020 10:47:43 +0000 (13:47 +0300)]
spi: dw: Fix native CS being unset
Commit
6e0a32d6f376 ("spi: dw: Fix default polarity of native
chipselect") attempted to fix the problem when GPIO active-high
chip-select is utilized to communicate with some SPI slave. It fixed
the problem, but broke the normal native CS support. At the same time
the reversion commit
ada9e3fcc175 ("spi: dw: Correct handling of native
chipselect") didn't solve the problem either, since it just inverted
the set_cs() polarity perception without taking into account that
CS-high might be applicable. Here is what is done to finally fix the
problem.
DW SPI controller demands any native CS being set in order to proceed
with data transfer. So in order to activate the SPI communications we
must set any bit in the Slave Select DW SPI controller register no
matter whether the platform requests the GPIO- or native CS. Preferably
it should be the bit corresponding to the SPI slave CS number. But
currently the dw_spi_set_cs() method activates the chip-select
only if the second argument is false. Since the second argument of the
set_cs callback is expected to be a boolean with "is-high" semantics
(actual chip-select pin state value), the bit in the DW SPI Slave
Select register will be set only if SPI core requests the driver
to set the CS in the low state. So this will work for active-low
GPIO-based CS case, and won't work for active-high CS setting
the bit when SPI core actually needs to deactivate the CS.
This commit fixes the problem for all described cases. So no matter
whether an SPI slave needs GPIO- or native-based CS with active-high
or low signal the corresponding bit will be set in SER.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Fixes:
ada9e3fcc175 ("spi: dw: Correct handling of native chipselect")
Fixes:
6e0a32d6f376 ("spi: dw: Fix default polarity of native chipselect")
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200515104758.6934-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Tue, 12 May 2020 11:03:15 +0000 (14:03 +0300)]
spi: dw: Drop duplicate error message when remap resource
devm_platform_ioremap_resource() will issue a message in the error case.
Thus, no need to duplicate in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512110315.58845-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kunihiko Hayashi [Fri, 24 Apr 2020 09:29:22 +0000 (18:29 +0900)]
spi: Convert UniPhier SPI controller to json-schema
Convert UniPhier SPI controller binding to DT schema format.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1587720562-15293-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jay Fang [Sat, 9 May 2020 02:29:51 +0000 (10:29 +0800)]
spi: dw-mmio: Do not add acpi modalias when CONFIG_ACPI is not enabled
Reduce unnecessary static memory allocation when CONFIG_ACPI is not enabled.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1588991392-24219-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alistair Francis [Mon, 11 May 2020 04:53:30 +0000 (21:53 -0700)]
spi: sun6i: Add support for GPIO chip select lines
Set use_gpio_descriptors as true to support using generic GPIO
lines for the chip select.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20200511045330.690507-1-alistair@alistair23.me
Signed-off-by: Mark Brown <broonie@kernel.org>
Kunihiko Hayashi [Mon, 11 May 2020 08:25:30 +0000 (17:25 +0900)]
spi: uniphier: Use devm_platform_get_and_ioremap_resource() to simplify code
Use devm_platform_get_and_ioremap_resource() to simplify code instead of
platform_get_resource() and devm_ioremap_resource(). This also gets
the resource that the following code uses.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1589185530-28170-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kunihiko Hayashi [Mon, 11 May 2020 08:25:29 +0000 (17:25 +0900)]
spi: uniphier: Depend on HAS_IOMEM
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, so the driver depends on this option.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1589185530-28170-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Thu, 7 May 2020 11:54:49 +0000 (14:54 +0300)]
spi: dw: Get rid of dma_inited flag
This flag is superfluous in all cases where it's being used, i.e.
* ->can_dma() won't be called without dma_inited == 1
* DMA ->exit() callback can rely on txchan and rxchan variables
So, get rid of dma_inited flag.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200507115449.8093-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Thu, 7 May 2020 11:54:48 +0000 (14:54 +0300)]
spi: dw: Avoid useless assignments in generic DMA setup
Generic DMA setup doesn't rely on certain type of DMA controller and thus
shouldn't use Intel Medfield settings, although it's harmless in this case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200507115449.8093-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jarkko Nikula [Wed, 6 May 2020 15:30:25 +0000 (18:30 +0300)]
spi: dw: Add Elkhart Lake PSE DMA support
Elkhart Lake PSE SPI is capable to utilize PSE DMA engine which is described
in ACPI. With help of acpi-dma module the support becomes a generic one.
Thus, add Elkhart Lake PSE DMA support and generic DMA hooks in SPI DesignWare
driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 6 May 2020 15:30:24 +0000 (18:30 +0300)]
spi: dw: Propagate struct device pointer to ->dma_init() callback
In some cases, one of which is coming soon, we would like to have
a struct device pointer to request DMA channel. For this purpose
propagate it to ->dma_init() callback in DMA ops.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 6 May 2020 15:30:23 +0000 (18:30 +0300)]
spi: dw: Add 'mfld' suffix to Intel Medfield related routines
In order to prepare driver for the extension to support newer hardware,
add 'mfld' suffix to some related functions.
While here, move DMA parameters assignment under existing #ifdef
CONFIG_SPI_DW_MID_DMA.
There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 6 May 2020 15:30:22 +0000 (18:30 +0300)]
spi: dw: Move few headers under #ifdef CONFIG_SPI_DW_MID_DMA
There is no user of few headers without CONFIG_SPI_DW_MID_DMA being set.
Move them under condition.
While at it, remove unused slab.h there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 6 May 2020 15:30:21 +0000 (18:30 +0300)]
spi: dw: Downgrade interrupt.h to irqreturn.h where appropriate
spi-dw-mid.c along with spi-dw.h are direct users of irqreturn.h
and nothing else is being used from interrupt.h. So, switch them
to use the former instead of latter one.
While here, move the header under #ifdef CONFIG_SPI_DW_MID_DMA
in spi-dw-mid.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 6 May 2020 15:30:20 +0000 (18:30 +0300)]
spi: dw: Move interrupt.h to spi-dw.h who is user of it
The actual user of interrupt.h is spi-dw.h and not bus drivers.
Move header there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 6 May 2020 15:30:19 +0000 (18:30 +0300)]
spi: dw: Remove unused variable in CR0 configuring hooks
After enabling new IP support in the driver couple of variables
were left unused compiler is not happy about:
.../spi-dw.c: In function ‘dw_spi_update_cr0’:
.../spi-dw.c:264:17: warning: unused variable ‘dws’ [-Wunused-variable]
264 | struct dw_spi *dws = spi_controller_get_devdata(master);
| ^~~
.../spi-dw.c: In function ‘dw_spi_update_cr0_v1_01a’:
.../spi-dw.c:285:17: warning: unused variable ‘dws’ [-Wunused-variable]
285 | struct dw_spi *dws = spi_controller_get_devdata(master);
| ^~~
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 6 May 2020 15:30:18 +0000 (18:30 +0300)]
spi: dw: Zero DMA Tx and Rx configurations on stack
Some DMA controller drivers do not tolerate non-zero values in
the DMA configuration structures. Zero them to avoid issues with
such DMA controller drivers. Even despite above this is a good
practice per se.
Fixes:
7063c0d942a1 ("spi/dw_spi: add DMA support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20200506153025.21441-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wei Yongjun [Wed, 6 May 2020 12:56:07 +0000 (12:56 +0000)]
spi: bcm2835: Fix error return code in bcm2835_dma_init()
Fix to return negative error code -ENOMEM from the dma mapping error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200506125607.90952-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jason Yan [Wed, 6 May 2020 06:19:11 +0000 (14:19 +0800)]
spi: a3700: make a3700_spi_init() return void
Fix the following coccicheck warning:
drivers/spi/spi-armada-3700.c:283:8-11: Unneeded variable: "ret". Return
"0" on line 315
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200506061911.19923-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wan Ahmad Zainie [Tue, 5 May 2020 13:06:17 +0000 (21:06 +0800)]
spi: dw-apb-ssi: Add Intel Keem Bay support
Document Intel Keem Bay SPI controller DT bindings.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-7-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wan Ahmad Zainie [Tue, 5 May 2020 13:06:15 +0000 (21:06 +0800)]
spi: dw-apb-ssi: Add compatible string for DesignWare DWC_ssi
This patch adds compatible string "snps,dwc-ssi-1.01a" to the above DT
binding document, to provide support for DesignWare DWC_ssi IP [1].
Current driver supports DW_apb_ssi IP [2].
References:
[1] https://www.synopsys.com/dw/ipdir.php?c=dwc_ssi
[2] https://www.synopsys.com/dw/ipdir.php?c=DW_apb_ssi
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-5-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wan Ahmad Zainie [Tue, 5 May 2020 13:06:16 +0000 (21:06 +0800)]
spi: dw: Add support for Intel Keem Bay SPI
Add support for Intel Keem Bay SPI controller, which uses DesignWare
DWC_ssi core. Bit 31 of CTRLR0 register is added for Keem Bay, to
configure the device as a master or as a slave serial peripheral.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-6-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wan Ahmad Zainie [Tue, 5 May 2020 13:06:14 +0000 (21:06 +0800)]
spi: dw: Add support for DesignWare DWC_ssi
This patch adds initial support for DesignWare DWC_ssi soft IP. DWC_ssi is
the enhanced version of DW_apb_ssi, which is currently supported by this
driver. Their registers are same, but the bit fields of register CTRLR0
are different.
DWC_ssi has additional features compared to DW_apb_ssi. Major enhancements
in DWC_ssi are hyper bus protocol, boot mode support and advanced XIP
support. DWC_ssi is an AHB slave device, whilst DW_apb_ssi is an APB slave
device.
Register offset
DW_ssi DW_apb_ssi
CTRLR0 0x00 0x00
CTRLR1 0x04 0x04
SSIENR 0x08 0x08
MWCR 0x0c 0x0c
SER 0x10 0x10
BAUDR 0x14 0x14
TXFTLR 0x18 0x18
RXFTLR 0x1c 0x1c
TXFLR 0x20 0x20
RXFLR 0x24 0x24
SR 0x28 0x28
IMR 0x2c 0x2c
ISR 0x30 0x30
RISR 0x34 0x34
TXOICR 0x38 0x38
RXOICR 0x3c 0x3c
RXUICR 0x40 0x40
MSTICR 0x44 0x44
ICR 0x48 0x48
DMACR 0x4c 0x4c
DMATDLR 0x50 0x50
DMARDLR 0x54 0x54
IDR 0x58 0x58
SSI_VERSION_ID 0x5c 0x5c
DRx (0 to 35) 0x60+i*0x4 0x60+i*0x4
RX_SAMPLE_DLY 0xf0 0xf0
SPI_CTRLR0 0xf4 0xf4
TXD_DRIVE_EDGE 0xf8 0xf8
XIP_MODE_BITS 0xfc RSVD
Register configuration - CTRLR0
DW_ssi DW_apb_ssi
SPI_HYPERBUS_EN bit[24] NONE
SPI_FRF bit[23:22] bit[22:21]
DFS_32 NONE bit[20:16]
CFS bit[19:16] bit[15:12]
SSTE bit[14] bit[24]
SRL bit[13] bit[11]
SLV_OE bit[12] bit[10]
TMOD bit[11:10] bit[9:8]
SCPOL | SPHA bit[9:8] bit[7:6]
FRF bit[7:6] bit[5:4]
DFS bit[4:0] bit[3:0]
The documents used are
[1] DW_apb_ssi_databook.pdf version 4.01a (2016.10a).
[2] DWC_ssi_databook.pdf version 1.01a.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-4-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wan Ahmad Zainie [Tue, 5 May 2020 13:06:13 +0000 (21:06 +0800)]
spi: dw: Add update_cr0() callback to update CTRLR0
This patch adds update_cr0() callback, in struct dw_spi.
Existing code that configure register CTRLR0 is moved into a new
function, dw_spi_update_cr0(), and this will be the default.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200505130618.554-3-wan.ahmad.zainie.wan.mohamad@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
projects / platform / kernel / linux-rpi.git / log