Stephen Warren [Wed, 19 Oct 2016 21:18:45 +0000 (15:18 -0600)]
ARM: tegra: translate __asm_flush_l3_cache to assembly
When performing a cache disable function, code must not access DRAM.
That is because when the cache is disabled, it will be bypassed and all
loads and stores will be serviced by RAM. This prevents accessing any
dirty data in the cache. In turn, this means the stack cannot be
used, since that is in RAM. To guarantee that code doesn't use RAM (and
in particular the stack) __asm_flush_l3_cache() must be manually
implemented in assembly, rather than implemented in C since the compiler
won't know not to touch RAM.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 19 Oct 2016 21:18:44 +0000 (15:18 -0600)]
ARM: tegra: ensure nvtboot_boot_x0 alignment
nvtboot_boot_x0 is a 64-bit variable and hence must be 64-bit aligned.
So far this has happened by accident! Fix the code so this is guaranteed.
This fixes the following build error:
... relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC
against symbol `nvtboot_boot_x0' ...
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tom Rini [Mon, 7 Nov 2016 18:16:00 +0000 (13:16 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-net
Siva Durga Prasad Paladugu [Wed, 2 Nov 2016 11:52:13 +0000 (12:52 +0100)]
net: use random ethernet address if invalid and not zero
Use random ethernet address if the ethernet address found
is invalid, not zero and config for random address
is defined.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Chris Packham [Mon, 31 Oct 2016 21:48:32 +0000 (10:48 +1300)]
net: mvgbe: Fix build error with CONFIG_PHYLIB
Commit
5a49f17481bb ("net: mii: Use spatch to update miiphy_register")
updated the mvgbe implementation of smi_reg_read/smi_reg_write. Prior to
that change mvgbe_phy_read and mvgbe_phy_write where used as wrappers to
satisfy the phylib APIs. Because these functions weren't updated in that
commit build errors where triggered when CONFIG_PHYLIB was enabled.
Fix these build errors by removing mvgbe_phy_read and mvgbe_phy_write
and using smi_reg_read/smi_reg_write directly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ash Charles [Fri, 21 Oct 2016 21:31:33 +0000 (17:31 -0400)]
net: phy: micrel: center FLP burst timing at 16ms
Like [1], reset the FLP burst timing for the KSZ9031 to the 16ms
specified by the IEEE802.3 standard from the chip's default of 8ms.
For more details, see the "Auto-Negotiation Timing" section of the
KSZ9031RNX datasheet.
[1] https://patchwork.kernel.org/patch/6558371/
Signed-off-by: Ash Charles <ash.charles@savoirfairelinux.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Mon, 12 Sep 2016 17:51:15 +0000 (11:51 -0600)]
ARM: tegra: enable Ethernet on p2771-0000
Enable the Ethernet device in DT, provide board-specific configuration,
and enable the driver in Kconfig.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Mon, 12 Sep 2016 17:51:14 +0000 (11:51 -0600)]
ARM: tegra: add DWC EQoS (ethernet) to Tegra186 DT
Tegra186 includes a Synopsys DWC EQoS (Ethernet) device. Add this to the
Tegra186 SoC DT so that boards can make use of it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Mon, 12 Sep 2016 17:51:13 +0000 (11:51 -0600)]
ARM: tegra: configure Ethernet address on Tegra186
On Tegra186, the bootloader which runs before U-Boot passes the Ethernet
MAC address to U-Boot using device tree. Extract this value and write it
to the environment, so that the Ethernet uclass picks it up and uses it
for the built-in Ethernet device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Mon, 12 Sep 2016 17:51:12 +0000 (11:51 -0600)]
ARM: tegra: add SoC-level hook for board_late_init()
Extend the Tegra186 implementation of board_late_init() to call a per-SoC
"hook" function. This will allow SoC-specific (rather than Tegra-wide)
functionality to be implemented without the core Tegra code needing to be
aware of the details. While board186.c is currently only used for
Tegra186, it should be applicable to any other future SoC, and perhaps its
simple design could be back-ported to older SoCs in the future too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Fri, 21 Oct 2016 20:46:47 +0000 (14:46 -0600)]
net: add driver for Synopsys Ethernet QoS device
This driver supports the Synopsys Designware Ethernet QoS (Quality of
Service) a/k/a eqos IP block, which is a different design than the HW
supported by the existing designware.c driver. The IP supports many
options for bus type, clocking/reset structure, and feature list. This
driver currently supports the specific configuration used in NVIDIA's
Tegra186 chip, but should be extensible to other combinations quite
easily, as explained in the source.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # V1
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Fri, 21 Oct 2016 20:46:46 +0000 (14:46 -0600)]
dt: net: add DWC EQoS binding
The Synopsys DWC EQoS is a configurable Ethernet MAC/DMA IP block which
supports multiple options for bus type, clocking and reset structure, and
feature list.
This patch imports the binding from the Linux kernel, including my V3
patch to extend the binding to cover the Tegra186, which is applied for
next-
20160912. So far, my changes have been acked by Lars Persson, the
original author of the binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fabio Estevam [Tue, 1 Nov 2016 16:58:16 +0000 (14:58 -0200)]
wandboard: Make Ethernet functional again
Since commit
ce412b79e7255770 ("drivers: net: phy: atheros: add separate
config for AR8031") ethernet does not work on mx6sabresd.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on wandboard design we need some additional configuration,
such as enabling the 125 MHz AR8031 output that needs to be done
in the board file.
This also aligns with the same method that the kernel performs
the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tomeu Vizoso [Fri, 4 Nov 2016 13:22:15 +0000 (14:22 +0100)]
mkimage: Allow including a ramdisk in FIT auto mode
Adds -i option that allows specifying a ramdisk file to be added to the
FIT image when we are using the automatic FIT mode (no ITS file).
This makes adding Depthcharge support to LAVA much more convenient, as
no additional configuration files need to be kept around in the machine
that dispatches jobs to the boards.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Matt Hart <matthew.hart@linaro.org>
Cc: Neil Williams <codehelp@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 5 Nov 2016 23:34:49 +0000 (19:34 -0400)]
travis-ci: Try harder to build all ARM targets
The way that we have things broken down currently allows for some
combinations of vendor or CPU to not be built. To fix this, create a
new catch-all job that excludes everything we've built elsewhere. For
the sake of simplicity we are allowing for the possibility of some
overlap between the vendor-based jobs and the CPU-based jobs. While
we're in here, make a failed build provide the summary of failure.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 5 Nov 2016 02:59:45 +0000 (22:59 -0400)]
buildman: Fix building based on 'options' field
The README for buildman says that we can use any field in boards.cfg to
decide what to build. However, we were not saving the options field
correctly.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fabio Estevam [Mon, 24 Oct 2016 12:22:06 +0000 (10:22 -0200)]
mx6sabresd: Make Ethernet functional again
Since commit
ce412b79e7255770 ("drivers: net: phy: atheros: add separate
config for AR8031") ethernet does not work on mx6sabresd.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabresd design we need some additional configuration,
such as enabling the 125 MHz AR8031 output that needs to be done
in the board file.
This also aligns with the same method that the kernel performs
the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Jagan Teki [Sat, 29 Oct 2016 19:44:31 +0000 (01:14 +0530)]
engicam: icorem6: Fix config files
Config file names on MAINTAINERS and README in
board/engicam/icorem6 seems to be wrong, hence fixed the same.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Thu, 3 Nov 2016 00:56:25 +0000 (00:56 +0000)]
armv8: define get_ticks() for the ARMv8 Generic Timer
For 64-bit ARM systems we provide just a timer_read_counter()
implementation and rely on the generic non-uclass get_ticks() function
in lib/time.c to call the former.
However this function is actually not 64-bit safe, as it assumes a
"long" to be 32-bit. Beside the fact that the resulting uint64_t
isn't bigger than "long" on 64-bit architectures and thus combining two
counters makes no sense, we get all kind of weird results when we try
to OR in the high value shifted by _32_ bits.
So let's avoid that function at all and provide a straight forward
get_ticks() implementation for ARMv8, which also is in line with ARMv7.
This fixes occasional immediate time-out expiration issues I see on the
Pine64 board. The root cause of this needs to be investigated, but this
fix looks like the right thing anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 3 Nov 2016 01:01:50 +0000 (01:01 +0000)]
doc: update README.arm64
This file apparently hasn't seen an update in a while, so just sync
it with reality.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Peng Fan [Fri, 4 Nov 2016 02:33:15 +0000 (10:33 +0800)]
tools: imximage: check return value when open the plugin file
Check return value when open the plugin file.
Coverity report:
** CID 153926: Error handling issues (NEGATIVE_RETURNS)
/tools/imximage.c: 542 in copy_plugin_code()
ifd = open(plugin_file, O_RDONLY|O_BINARY);
>>> CID 153926: Error handling issues (NEGATIVE_RETURNS)
>>> "ifd" is passed to a parameter that cannot be negative.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reported-by: Coverity (CID: 153926)
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Mon, 31 Oct 2016 16:21:09 +0000 (10:21 -0600)]
image: Protect against overflow in unknown_msg()
Coverity complains that this can overflow. If we later increase the size
of one of the strings in the table, it could happen.
Adjust the code to protect against this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 150964)
Marcel Ziswiler [Fri, 28 Oct 2016 20:50:23 +0000 (22:50 +0200)]
colibri_pxa270: drop lzma support for space reason
As the upcoming driver model integration takes up some more precious flash
space first make sure to drop expensive LZMA support.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tom Rini [Thu, 3 Nov 2016 11:09:42 +0000 (07:09 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Patrick Delaunay [Fri, 28 Oct 2016 07:44:26 +0000 (09:44 +0200)]
dfu: align array in dfu_get_dev_type with enum dfu_device_type
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Michal Simek [Tue, 30 Aug 2016 13:32:17 +0000 (15:32 +0200)]
cmd: dfu: Add error handling for board_usb_init
board_usb_init() can failed and error should be handled properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Wed, 2 Nov 2016 13:41:20 +0000 (09:41 -0400)]
Merge git://git.denx.de/u-boot-rockchip
Tom Rini [Mon, 31 Oct 2016 20:36:10 +0000 (16:36 -0400)]
Prepare v2016.11-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Jelle van der Waa [Sun, 30 Oct 2016 16:30:30 +0000 (17:30 +0100)]
README: fix typo candiate -> candidate
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tom Rini [Sat, 29 Oct 2016 21:11:17 +0000 (17:11 -0400)]
travis.yml: Add in uniphier as a job, modify aarch64 builds a bit
- Add in system aarch64-linux-gnu toolchain
- Now that all VMs will have aarch64 available, don't exclude them from
other jobs but instead exclude them from the catch-all aarch64 build
- Add JOB= to the Freescale/ARM build to be clear about what it does.
- Add uniphier as a stand-alone job
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Thu, 27 Oct 2016 23:54:03 +0000 (17:54 -0600)]
mkimage: Fix missing free() in show_valid_options()
The allocated memory should be freed. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 150963)
Reviewed-by: Tom Rini <trini@konsulko.com>
Chris Packham [Tue, 25 Oct 2016 07:22:48 +0000 (20:22 +1300)]
cmd: load: align cache flush
Prevent cache misalignment message by ensuring that a whole cache line
is flushed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Vagrant Cascadian [Mon, 24 Oct 2016 03:45:19 +0000 (20:45 -0700)]
Fix spelling of "resetting".
Cover-Letter: Fixes several spelling errors for the words "resetting",
"extended", "occur", and "multiple".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vagrant Cascadian [Mon, 24 Oct 2016 03:45:18 +0000 (20:45 -0700)]
Fix spelling of "extended".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vagrant Cascadian [Mon, 24 Oct 2016 03:45:17 +0000 (20:45 -0700)]
Fix spelling of "occur".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vagrant Cascadian [Mon, 24 Oct 2016 03:45:16 +0000 (20:45 -0700)]
Fix spelling of "multiple".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Sun, 23 Oct 2016 12:39:01 +0000 (07:39 -0500)]
omap3logic: Fix Auto detect Logic PD Models
The autodetect feature doesn't allow users to specify the device tree.
This fix will make it only autodetect if 'fdtimage' is not defined.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adam Ford [Sat, 15 Oct 2016 13:16:27 +0000 (08:16 -0500)]
OMAP3: omap3_logic: Add scripts to boot over network.
Not all networks have a DHCP server configured properly, so these
scripts make it easier to boot in that scenario.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adam Ford [Sat, 15 Oct 2016 11:23:11 +0000 (06:23 -0500)]
OMAP3: omap3_logic: Remove LCD preboot info
The LCD isn't supported in U-Boot and the LCD is now configured in
the device tree, so this code is pointless.
V2: Eliminiate erroneous newline.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 11 Oct 2016 17:39:05 +0000 (12:39 -0500)]
ti: common: board_detect: Return a valid empty string for un-initialized eeprom
Current logic for query of revision, board_name, config returns
NULL. Users of these functions do a direct strncmp to compare.
Unfortunately, as per conventions require two valid strings to compare
against and the current implementation causes a crash when compared
with NULL.
We'd still like to maintain the simplistic usage of these APIs instead
of redundant if (string) res=strncmp(fn(),"cmp",n); flowing all over
the place.
Hence, since the version, name and config is already pre-initialized
with empty string, just dont check for invalid header in the first
place and return the empty string to the caller.
Reported-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Correct was'nt -> wasn't typo]
Signed-off-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 11 Oct 2016 17:39:04 +0000 (12:39 -0500)]
ti: common: board_detect: Setup initial default value for config as well
config should have been initialized along with others as defaults.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 11 Oct 2016 17:39:03 +0000 (12:39 -0500)]
ti: common: board_detect: Replace hardcoded value with macro
We should have used TI_DEAD_EEPROM_MAGIC in the first place.
Fixes:
d3b98a9eb941 ("ti: common: dra7: Add standard access for board description EEPROM")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Alexander von Gernler [Fri, 7 Oct 2016 17:44:14 +0000 (19:44 +0200)]
cosmetic: Fix indentation in README
Signed-off-by: Alexander von Gernler <grunk@pestilenz.org>
Kever Yang [Sat, 8 Oct 2016 07:23:38 +0000 (15:23 +0800)]
rk3288: kconfig: remove duplicate definition of SPL_MMC_SUPPORT
SPL_MMC_SUPPORT defined in rockchip top level Kconfig instead of
inside rk3288 and default to disable if ROCKCHIP_SPL_BACK_TO_BROM
defined.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jacob Chen [Sat, 8 Oct 2016 05:47:42 +0000 (13:47 +0800)]
rockchip: doc: add GPT partition layout
A simple introduction.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Jacob Chen [Sat, 8 Oct 2016 05:47:41 +0000 (13:47 +0800)]
rockchip: use rockchip linux partitions layout
Unify the partitions of each chip then it will be more easy for us to
write scripts, tools or guides for rockchip chips.
Those extra partitions mostly are used to be compatible with our
internal loaders (such as miniloader which was same as spl, or
android loader then we can support dual boot)
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 7 Oct 2016 09:47:59 +0000 (17:47 +0800)]
dts: rk3288: remove node in dmc which not need anymore
Since we implement the dram capacity auto detect, we don't
need to set the channel number and sdram-channel in dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Kever Yang [Fri, 7 Oct 2016 09:47:58 +0000 (17:47 +0800)]
rk3288: sdram: auto-detect the capacity
Add support for rk3288 dram capacity auto detect, support DDR3 and
LPDDR3, DDR2 is not supported.
The program will automatically detect:
- channel number
- rank number
- column address number
- row address number
The dts file do not need to describe those info after apply this patch.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Kever Yang [Fri, 7 Oct 2016 09:47:57 +0000 (17:47 +0800)]
rk3288: config change for enable dram capacity auto-detect.
Enable ROCKCHIP_SPL_BACK_TO_BROM and disable CONFIG_SPL_MMC_SUPPORT
to save memory in order to enable add source code for dram capacity
auto-detect.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 7 Oct 2016 08:05:45 +0000 (16:05 +0800)]
evb-rk3399: config: set emmc as default boot dev
rk3399 has two mmc dev controller:
mmc 0: SD card;
mmc 1: EMMC
U-Boot will scan the mmc boot device configured by CONFIG_SYS_MMC_ENV_DEV,
since evb has emmc on board, let's set the EMMC as default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 7 Oct 2016 07:59:49 +0000 (15:59 +0800)]
rk3288: fix reg address for GRF_SOC_CON2
The GRF base address is missing, fix it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 7 Oct 2016 07:56:16 +0000 (15:56 +0800)]
rk3399: disable the clock multiplier support when SoC init
The Clock Multiplier in rk3399 EMMC programmable clock generator
is broken, we can remove its support from SoC GRF register.
Without this patch, rk3399 emmc driver is not work after below patch
applied:
6dffdbc mmc: sdhci: Add the programmable clock mode support
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Simon Glass [Sun, 2 Oct 2016 02:04:52 +0000 (20:04 -0600)]
rockchip: rk3288: Move rockchip_get_cru() out of the driver
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Simon Glass [Sun, 2 Oct 2016 02:04:51 +0000 (20:04 -0600)]
rockchip: rk3399: Move rockchip_get_cru() out of the driver
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Simon Glass [Sun, 2 Oct 2016 02:04:50 +0000 (20:04 -0600)]
rockchip: rk3036: Move rockchip_get_cru() out of the driver
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jacob Chen [Tue, 27 Sep 2016 07:48:45 +0000 (15:48 +0800)]
clk: rk3399: fix rockchip_get_cru
clk_rk3399 is driver name, not device name
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sandy Patterson [Mon, 11 Jul 2016 17:38:52 +0000 (13:38 -0400)]
rockchip: RK3288 needs fdt and initrd below 256M now
I am not sure why this limit is changing. But my kernel
doesn't load when it's above 256. This was testing on the
rock2 board.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Updated commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sun, 30 Oct 2016 12:12:00 +0000 (08:12 -0400)]
Merge branch 'sun9i-a80-spl' of git.denx.de/u-boot-sunxi
Tom Rini [Sun, 30 Oct 2016 12:11:50 +0000 (08:11 -0400)]
Merge branch 'master' of git.denx.de/u-boot-sunxi
Chen-Yu Tsai [Fri, 28 Oct 2016 10:21:38 +0000 (18:21 +0800)]
sunxi: Add support for Cubieboard4
The Cubieboard4 is an A80 SoC based development board from Cubietech.
This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector,
HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT
combo chip, headphone and microphone jacks, IR receiver, and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stefan BrĂ¼ns [Sat, 29 Oct 2016 10:23:18 +0000 (12:23 +0200)]
tools: add mksunxiboot to tools-all target
mksunxiboot is useful outside of u-boot, it is e.g. used by sunxi-tools.
Signed-off-by: Stefan BrĂ¼ns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Fri, 28 Oct 2016 10:21:37 +0000 (18:21 +0800)]
sunxi: Enable SPL support for A80 Optimus board
The A80 Optimus Board was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, 2 USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash,
2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig
instead of adding a new defconfig]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Amit Singh Tomar [Fri, 21 Oct 2016 01:24:30 +0000 (02:24 +0100)]
sunxi: A64: enable USB support
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Fri, 28 Oct 2016 10:21:36 +0000 (18:21 +0800)]
sunxi: Add default zq value for sun9i (A80)
Both the A80 Optimus board and the Cubieboard 4 use a zq value of
4145117, or 0x3f3fdd.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stefan Mavrodiev [Sat, 29 Oct 2016 12:34:07 +0000 (14:34 +0200)]
sunxi: Update DRAM clock for Olimex A20 boards
Originally dram clock was set to 480MHz, but this behaves
unstable. To improve stability the clock is reduced to 384MHz
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Fri, 28 Oct 2016 10:21:35 +0000 (18:21 +0800)]
sunxi: Add support for SID e-fuses on sun9i
The A80 has SID e-fuses. Like other newer SoCs, the actual e-fuses
are at an offset of 0x200 within the SID address space.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Andre Przywara [Fri, 21 Oct 2016 00:11:46 +0000 (01:11 +0100)]
sunxi: dts: Pine64: add Ethernet alias
The sun8i-emac driver works fine with the A64 Ethernet IP, but we are
missing an alias entry to trigger the driver instantiation by U-Boot.
Add the line to point U-Boot to the Ethernet DT node.
This enables TFTP boot on the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Fri, 28 Oct 2016 10:21:34 +0000 (18:21 +0800)]
sunxi: Set default CPU clock rate to 1008 MHz for sun9i (A80)
In Allwinner's SDK the A80 is clocked to 1008 MHz by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Masahiro Yamada [Thu, 13 Oct 2016 15:40:01 +0000 (00:40 +0900)]
sunxi: remove unneeded CONFIG_USB_MAX_CONTROLLER_COUNT defines
ARCH_SUNXI selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT
is not used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:33 +0000 (18:21 +0800)]
sunxi: add MMC pinmux setup for SDC2 on sun9i
The A80 can support 8-bit eMMC with reset on the PC pingroups.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Jagan Teki [Thu, 13 Oct 2016 08:49:35 +0000 (14:19 +0530)]
sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXI
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:32 +0000 (18:21 +0800)]
sunxi: enable SPL for sun9i
Now that DRAM initialization and clock setup is supported,
we can enable SPL for the A80.
[wens@csie.org: Added commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:31 +0000 (18:21 +0800)]
sunxi: add initial clock setup for sun9i for SPL
This is a cleaned up version set_pll() from Allwinner's boot0 source
(bootloader/basic_loader/bsp/bsp_for_a80/common/common.c).
[wens@csie.org: Added commit message; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:30 +0000 (18:21 +0800)]
sunxi: Enable SMP mode for the boot CPU on sun9i (A80)
Since the A80 has many cores which we intend to use in SMP fashion,
we should set the SMP bit for the boot CPU.
[wens@csie.org: Added commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:29 +0000 (18:21 +0800)]
sunxi: add gtbus-initialisation for sun9i
On sun9i, the GTBUS manages transaction priority and bandwidth
for multiple read ports when accessing DRAM. The initialisation
mirrors the settings from Allwinner's boot0 for now, even though
this may not be optimal for all applications (e.g. headless
systems might want to give priority to IO modules).
Adding a common callout to gtbus_init() from the SPL clock init
with a weakly defined implementation in sunxi/clock.c to fallback
to for platforms that don't require this.
[wens@csie.org: Moved gtbus_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:28 +0000 (18:21 +0800)]
sunxi: DRAM initialisation for sun9i
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tom Rini [Sat, 29 Oct 2016 21:16:00 +0000 (17:16 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
Tom Rini [Sat, 29 Oct 2016 21:15:37 +0000 (17:15 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Tom Rini [Sat, 29 Oct 2016 21:15:24 +0000 (17:15 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier
Andre Przywara [Fri, 21 Oct 2016 01:24:29 +0000 (02:24 +0100)]
drivers: USB: OHCI: allow compilation for 64-bit targets
OHCI has a known limitation of allowing only 32-bit DMA buffer
addresses, so we have a lot of u32 variables around, which are assigned
to pointers and vice versa. This obviously creates issues with 64-bit
systems, so the compiler complains here and there.
To allow compilation for 64-bit boards which use only memory below 4GB
anyway (and to avoid more invasive fixes), adjust some casts and types
and assume that the EDs and TDs are all located in the lower 4GB.
This fixes compilation of the OHCI driver for the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tom Rini [Sat, 29 Oct 2016 12:41:45 +0000 (08:41 -0400)]
configs/chromebox_panther_defconfig: Re-enable CONFIG_DM_PCI
This was turned off by accident, re-enble.
Signed-off-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Fri, 28 Oct 2016 17:57:34 +0000 (23:27 +0530)]
MAINTAINERS: Update Jagan's email
Signed-off-by: Jagan Teki <jagan@openedev.com>
Stephen Warren [Wed, 26 Oct 2016 19:05:52 +0000 (13:05 -0600)]
travis-ci: build Tegra boards
ARMv7 Tegra boards aren't currently covered by any other travis-ci jobs.
Add a new job to build them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:36 +0000 (11:05 -0600)]
travis-ci: compile with buildman when running test/py
Use buildman to compile any U-Boot binary tested by test/py. This
re-uses all the work done elsewhere to make buildman work within
Travis-CI, in particular related to toolchain downloading and buildman
config file creation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:10 +0000 (23:47 +0900)]
ARM: uniphier: update DRAM init code for LD11 SoC
Introduce run-time DDR PHY training.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:09 +0000 (23:47 +0900)]
ARM: uniphier: support DDR PHY parameter dump command for LD11
Add the LD11 SoC data and adjuts the printf() format because this is
a 64-bit SoC. Otherwise, 16-digits pointer addresses would break
the log format.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:08 +0000 (23:47 +0900)]
ARM: uniphier: refactor DDR PHY parameter dump command
Do not hard-code the number of DX blocks because it is a different
value for LD11 SoC.
Move the macro NR_DATX8_PER_DDRPHY to ddrphy-training.c since it
is the last user.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:07 +0000 (23:47 +0900)]
ARM: uniphier: rework existing DDR PHY code to reuse for LD11 SoC
The DDR PHY register view of LD11 is slightly different from that
of LD4/Pro4/sLD8, but it will be possible to share the register
macros (and I want to re-use as much code as possible). Change
the code in the more flexible form.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:06 +0000 (23:47 +0900)]
ARM: uniphier: do not run harmful code for USB boot mode of LD11 ES3
The USB boot without the stand-by MPU is available on ES3 or later
of LD11 SoC, but the code in this if-conditional block must not be
run when booting from USB. Check if the boot device is USB, and
skip the code in the case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:05 +0000 (23:47 +0900)]
ARM: uniphier: enable clocks to MIO/STDMAC on LD11 if USB is enabled
At the moment, the clk driver is not clever enough to automatically
enable parent clocks like Linux. Enable the STDMAC clock explicitly
if USB is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:04 +0000 (23:47 +0900)]
ARM: uniphier: fix DRAM init poll address for LD4, Pro4, sLD8
The status register should be polled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:03 +0000 (23:47 +0900)]
ARM: uniphier: rename ddrphy-ld20-regs.h to ddruqphy-regs.h
This PHY might be used for other SoCs in the future.
Avoid including the SoC name in the header name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:02 +0000 (23:47 +0900)]
ARM: uniphier: update DRAM init code for LD20 SoC (3rd)
- Constify UMC setting data arrays
- Merge data arrays *_d0 and *_d1.
- Add PHY parameters for LD20 C1 board
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:01 +0000 (23:47 +0900)]
ARM: uniphier: remove unused board attribute macros
After SoC evaluation, they turned out unnecessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 27 Oct 2016 14:47:00 +0000 (23:47 +0900)]
ARM: uniphier: enable SSC for more PLLs for LD20 SoC
For Electro-Magnetic Compatibility.
Set CPLL, SPLL2, MPLL, VPPLL, GPPLL, DPLL* to SSC rate 1 percent.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 19 Oct 2016 07:26:49 +0000 (16:26 +0900)]
ARM: uniphier: remove unneeded mdelay() in PLL setting function
This delay is already cared by the callers of this function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 17 Oct 2016 13:18:02 +0000 (22:18 +0900)]
ARM: uniphier: adjust fdt_file environment handling to latest Linux
The environment fdt_file is useful to remember the appropriate DTB
file name. Adjust it to the recent renaming in the upstream kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Stephen Warren [Wed, 26 Oct 2016 17:05:35 +0000 (11:05 -0600)]
travis-ci: don't invoke exit on success
Invoking exit prevents any subsequent build commands from running, and
future patches will add extra commands.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:34 +0000 (11:05 -0600)]
travis-ci: use buildman -P everywhere
This places build results into a board-specific directory rather than a
buildman-thread-specific directory. This is required so that we can
access the directory from test.py, and there's no risk of a particular
build's results being over-written by another build performed by the
same thread.
In theory, this can lead to slower builds when building many different
boards in a single buildman thread, since it removes the possibility of
incremental builds between boards. In practice however I didn't notice
longer build times when when enabling this option; if anything build
times decreased although I suspect that's simply due to general
variations in build performance across different machines within the
Travis CI infra-structure.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 26 Oct 2016 17:05:33 +0000 (11:05 -0600)]
travis-ci: centralize ~/.buildman editing
Any time an x86 toolchain is used, we need to edit ~/.buildman to
reference it. Move the editing logic into a central place so that it
doesn't have to be duplicated everywhere that uses the x86 toolchain;
future patches will add additional cases where it's used.
It would be nice if we could unconditionally write all of ~/.buildman at
once. Unfortunately, buildman fails if any toolchain mentioned in a
toolchain-prefix entry doesn't exist, even if it doesn't need to use it
for the current build.
The sandbox/x86 build definition currently does nothing more than edit
~/.buildman; no builds are run. Fix this by not defining a custom script
for this build, and hence preventing that stanza from replacing the
default script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>