Marek Vasut [Sat, 16 Jan 2021 23:16:16 +0000 (00:16 +0100)]
net: phy: micrel: Try default PHY ofnode first
The phydev structure has a PHY OF node pointer in it, use that OF node
first when looking up PHY OF node properties, since that is likely the
correct PHY OF node pointer. If the pointer is not valid, which is the
case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Alex Nemirovsky [Thu, 14 Jan 2021 21:34:13 +0000 (13:34 -0800)]
board: presidio-asic: Add CAxxxx Ethernet support
Add CAxxxx Ethernet support for the Cortina Access
Presidio Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Abbie Chang [Thu, 14 Jan 2021 21:34:12 +0000 (13:34 -0800)]
net: phy: ca_phy: Add driver for CAxxxx SoCs
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Aaron Tseng [Thu, 14 Jan 2021 21:34:11 +0000 (13:34 -0800)]
net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs
Add Cortina Access Ethernet device driver for CAxxxx SoCs.
This driver supports both legacy and DM_ETH network models.
Signed-off-by: Aaron Tseng <aaron.tseng@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Abbie Chang <abbie.chang@Cortina-Access.com>
CC: Tom Rini <trini@konsulko.com>
Yang Liu [Mon, 21 Dec 2020 03:44:39 +0000 (14:44 +1100)]
net: fix ping in netconsole
Should not init eth device when doing ping in netconsole.
Signed-off-by: Yang Liu <yliu@cybertec.com.au>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Stefan Roese [Mon, 16 Nov 2020 17:02:30 +0000 (18:02 +0100)]
net: e1000: Add missing address translations
Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Stefan Roese [Mon, 16 Nov 2020 17:02:29 +0000 (18:02 +0100)]
net: e1000: Use virt_to_phys() instead of pci_virt_to_mem()
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Stefan Roese [Mon, 16 Nov 2020 17:02:28 +0000 (18:02 +0100)]
net: e1000: Remove unused bus_to_phys() macro
bus_to_phys() is defined but not referenced at all. This patch removes
it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Tom Rini [Tue, 26 Jan 2021 00:46:02 +0000 (19:46 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi
- New Allwinner H616 SoC support (sans Ethernet & USB)
- H6 DT update
- Tanix TX6 TV box support
- OrangePi 3 support
- OrangePi Zero2 (H616) support
Jernej Skrabec [Mon, 11 Jan 2021 20:11:53 +0000 (21:11 +0100)]
sunxi: Add support for OrangePi Zero2
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:52 +0000 (21:11 +0100)]
clk: sunxi: Add support for H616 clocks
This commit introduces DM H616 clock driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:51 +0000 (21:11 +0100)]
sunxi: gpio: introduce compatible for H616
H616 pinctrl is no different configuration wise than others, so just add
compatible for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:50 +0000 (21:11 +0100)]
arm: sunxi: add initial H616 DTSI and headers
This commit introduces H616 DTSI file and dt-bindings headers needed for
device tree files.
Files are taken from v3 Linux H616 support submission[1], as the
H616 .dtsi file is not merged upstream yet.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632082.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:48 +0000 (21:11 +0100)]
sunxi: Add H616 FEL support
H616 uses different address for reset. Add it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:46 +0000 (21:11 +0100)]
sunxi: Add support for H616 SoC
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 11 Jan 2021 20:11:44 +0000 (21:11 +0100)]
mmc: sunxi: Refactor mod clock register offset
So far the only difference between the various Allwinner MMC controller
we are concerned about is the mod clock register offset.
This is actually not directly related to the MMC controller IP, but an
integration choice, dependent on the SoC this appears in.
To avoid becoming trapped with some compatible fallback strings, let's
remove the whole struct sunxi_mmc_variant, and replace this with a SoC
based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols.
This will later simplify H616 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:43 +0000 (21:11 +0100)]
sunxi: Add H616 DRAM support
Allwinner H616 supports many types of DRAM. Most notably it supports
LPDDR4. However, all commercially available boards at this time use
only DDR3, so this commit adds only DDR3 support.
Controller and MBUS are very similar to H6 but PHY is completely
unknown.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:42 +0000 (21:11 +0100)]
sunxi: add support for R_I2C on H616
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:41 +0000 (21:11 +0100)]
sunxi: add support for H616 uart0
This port is used for debug terminal on all known H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:40 +0000 (21:11 +0100)]
sunxi: introduce support for H616 clocks
H616 has mostly the same clocks as H6 with some small differences. Just
reuse H6 clocks for H616 and handle differences with macros.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 11 Jan 2021 20:11:39 +0000 (21:11 +0100)]
sunxi: support loading with SPL > 32KB
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:38 +0000 (21:11 +0100)]
sunxi: Add support for I2C on H6 like SoCs
I2C support, especially R_I2C port, will be needed in future. Upcoming
support for H616 will need R_I2C to adjust DRAM voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:37 +0000 (21:11 +0100)]
sunxi: prcm: Add memory map for H6 like SoCs
There was no need to have prcm definitions for H6 and similar SoCs till
now. However, support R_I2C will be needed soon in SPL.
Move old definitions to prcm_sun6i.h and add new ones in prcm_sun50i.h.
One of those files will be selected in common prcm.h based on defined
macros.
This commit doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:36 +0000 (21:11 +0100)]
i2c: mvtwsi: sunxi: update macro
While currently none of the newer Allwinner SoCs currently has I2C
support implemented in U-Boot, this will change soon. mvtwsi driver is
good as it is for them except one macro. Update it to be ready once I2C
support lands for those SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:35 +0000 (21:11 +0100)]
mmc: sunxi: Replace H6 ifdefs with H6 gen macro
It turns out that several SoCs share same mmc configuration as H6. In
order to lower ifdef clutter replace H6 specific macro with common one.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:34 +0000 (21:11 +0100)]
sunxi: Introduce common symbol for H6 like SoCs
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:33 +0000 (21:11 +0100)]
sunxi: Add support for AXP305 PMIC
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 18 Jan 2021 23:23:59 +0000 (23:23 +0000)]
sunxi: Properly check for SATAPWR and MACPWR
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!
Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Andre Heider [Fri, 1 Oct 2021 18:29:00 +0000 (19:29 +0100)]
sunxi: Add support for Orange Pi 3
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Wed, 6 Jan 2021 17:02:57 +0000 (18:02 +0100)]
sunxi: Add support for Tanix TX6
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Wed, 6 Jan 2021 17:02:56 +0000 (18:02 +0100)]
ARM: dts: sunxi: h6: Update DT files
Updated H6 DT files are based on Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sat, 14 Nov 2020 17:37:46 +0000 (17:37 +0000)]
net: sun8i-emac: Allow all RGMII PHY modes
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Mon, 25 Jan 2021 19:38:40 +0000 (14:38 -0500)]
Merge tag 'mips-pull-2021-01-24' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- MIPS: add support for Mediatek MT7620 SoCs
Tom Rini [Mon, 25 Jan 2021 14:02:35 +0000 (09:02 -0500)]
Merge tag 'u-boot-imx-
20210125' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Changes for 2020.04
-------------------
- new board:
Phytec phyCORE-i.MX8MP
i.MX8MN Beacon EmbeddedWorks devkit
- Fixes:
several nanbcb fixes
fix for imx8mm_beacon
- further switch to distro boot commands
- DM:
DM Ether for MX6UL
CI:
https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6013
Tom Rini [Mon, 25 Jan 2021 14:02:06 +0000 (09:02 -0500)]
Merge tag 'doc-2021-04-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for documentation tag doc-2021-04-rc1 (2)
* Man-pages for sbi, exit, for, echo, loady, true, false, conitrace
* Adjust suppression of newline in echo command.
* Provide unit test for echo command.
Tom Rini [Mon, 25 Jan 2021 14:01:28 +0000 (09:01 -0500)]
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Heinrich Schuchardt [Mon, 25 Jan 2021 00:11:47 +0000 (01:11 +0100)]
doc: describe command conitrace
Provide a man-page for the conitrace command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 24 Jan 2021 21:11:55 +0000 (22:11 +0100)]
doc: describe the false command
Provide a man-page for the false command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 24 Jan 2021 20:48:00 +0000 (21:48 +0100)]
dm: core: describe uclass_root_s
'make htmldocs' creates a warning:
./include/asm-generic/global_data.h:443:
warning: Function parameter or member 'uclass_root_s'
not described in 'global_data'
Correct the member descriptions.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Fri, 22 Jan 2021 18:25:53 +0000 (19:25 +0100)]
doc: document true command
Create a man-page for the true command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Fri, 22 Jan 2021 18:18:01 +0000 (19:18 +0100)]
doc: describe loady command
Create a man-page for the loady command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Fri, 22 Jan 2021 12:16:04 +0000 (13:16 +0100)]
cmd: correct long text loadb, loadx, loady
The first argument is the load address and not an offset.
The second argument cannot be entered without the first one.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Thu, 21 Jan 2021 16:33:44 +0000 (17:33 +0100)]
doc: document echo command
Provide a man-page for the echo command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Thu, 21 Jan 2021 17:41:28 +0000 (18:41 +0100)]
test: unit test for echo command
Provide a unit test for the unit command
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Wed, 20 Jan 2021 11:13:30 +0000 (12:13 +0100)]
cmd: change suppress newline in echo command
By default the echo command emits its arguments followed by a line feed.
If any of the arguments contains the sub-string "\c", the line feed is
suppressed.
This does not match shells used in Linux and BSD where the first argument
has to be -n to suppress the line feed.
The hush shell interferes with the parsing of backslashes. E.g. in the
following command line quadruple backslashes are required for suppressing
the line feed:
for i in 1 2 3; do for j in 4 5; do echo \\\\c ${i}${j}; done; echo; done;
To avoid unexpected behavior the patch changes echo to use -n as first
argument to suppress the line feed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Wed, 20 Jan 2021 17:09:30 +0000 (18:09 +0100)]
doc: document for statement
Create a man-page for the for statement.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 20 Jan 2021 11:14:01 +0000 (12:14 +0100)]
doc: describe exit command
Man-page for exit shell command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 19 Jan 2021 18:30:04 +0000 (19:30 +0100)]
doc: document sbi command
Add a man-page for the sbi command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Weijie Gao [Thu, 12 Nov 2020 08:37:19 +0000 (16:37 +0800)]
MAINTAINERS: add maintainer for MediaTek MIPS platform
Update maintainer for MediaTek MIPS platform
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:37:14 +0000 (16:37 +0800)]
reset: reset-mtmips: add DM_FLAG_PRE_RELOC flag
Add DM_FLAG_PRE_RELOC flag for reset-mtmips to make sure this driver can
be probed before relocation even if u-boot,dm-pre-reloc is not present
in the dts.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:37:07 +0000 (16:37 +0800)]
mmc: mtk-sd: assign plat->cfg.f_max with a correct value
Currently this driver does not set the value of plat->cfg.f_max, which
results in that MMC framework will always run at the lowest frequency.
This patch sets plat->cfg.f_max to the maximum allowed frequency, which
equals to the source clock frequency.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:37:02 +0000 (16:37 +0800)]
mmc: mtk-sd: add pad control settings for MediaTek MT7620/MT76x8 SoCs
The driver is missing pad control settings (pad delay and pad conf) for
the mt7620 and mt76x8. Although mt76x8 still works well, mt7620 will
encounter CRC error on data transfers.
This patch adds default pad control settings for mt7620_compat.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:57 +0000 (16:36 +0800)]
mmc: mtk-sd: fix sclk cycles shift value
It turns out that the sclk cycles used by mt7620/mt7628 is the same as
other chips (20 bits, 1048576), not 65536.
This patch removes sclk_cycle_shift from dev_comp, and uses a macro with
a value 20 instead.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:53 +0000 (16:36 +0800)]
net: add ethernet driver for MediaTek MT7620 SoC
This patch adds ethernet driver for MediaTek MT7620 SoC.
The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in
7-port switch and two xMII interfaces (can be MII/RMII/RGMII).
The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be
configured to connect to either the intergrited FE PHY, or the xMII.
Port 5 always connects to the xMII. Port 6 is the CPU port.
This driver supports MT7530 giga switch connects to port 5.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:48 +0000 (16:36 +0800)]
phy: add USB PHY driver for MediaTek MT7620 SoC
This patch adds USB PHY driver for MediaTek MT7620 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:42 +0000 (16:36 +0800)]
spi: add spi controller support for MediaTek MT7620 SoC
This patch adds spi controller support for MediaTek MT7620 SoC.
The SPI controller supports two chip selects. These two chip selects are
implemented as two separate register groups, but they share the same bus
(DI/DO/CLK), only CS pins are dedicated for each register group.
Appearently these two register groups cannot operates simulataneously so
they are implemented as one controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:33 +0000 (16:36 +0800)]
gpio: add GPIO controller driver for MediaTek MT7620 SoC
This patch adds GPIO controller driver for MediaTek MT7620 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:28 +0000 (16:36 +0800)]
watchdog: add watchdog driver for MediaTek MT7620 SoC
This patch adds watchdog support for the Mediatek MT7620 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:24 +0000 (16:36 +0800)]
pinctrl: mtmips: add support for MediaTek MT7620 SoC
This patch adds pinctrl support for MediaTek MT7620 SoC.
The MT7620 SoC supports only pinmux.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:19 +0000 (16:36 +0800)]
reset: mtmips: add reset controller support for MediaTek MT7620 SoC
This patch adds reset controller bits definition header file for MediaTek
MT7620 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:10 +0000 (16:36 +0800)]
clk: add clock driver for MediaTek MT7620 SoC
This patch adds a clock driver for MediaTek MT7620 SoC.
This driver provides clock gate control as well as getting clock frequency
for CPU/SYS/XTAL and some peripherals.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:05 +0000 (16:36 +0800)]
serial: add uart driver for MediaTek MT7620 SoC
This patch adds uart support for MediaTek MT7620 and earlier SoCs.
The UART used by MT7620 is incompatible with the ns16550a driver.
All registers of this UART have different addresses. A special 16-bit
register for Divisor Latch is used to set the baudrate instead of the
original two 8-bit registers (DLL and DLM).
The driver supports of-platdata which is useful for tiny SPL.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:36:00 +0000 (16:36 +0800)]
configs: mtmips: refresh for mt7628 based boards
Since mt7620 is added into Kconfig, the CONFIG_SOC_MT7628=y which is
omitted by default must be added back, otherwise make xxx_defconfig for
these boards will be configured for mt7620 platform.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:56 +0000 (16:35 +0800)]
mips: mtmips: add two reference boards for mt7620
The mt7620_rfb board supports integrated 10/100M PHYs plus two external
giga PHYs. It also has 8MB SPI-NOR, mini PCI-e x1 slot, SDHC and USB.
The mt7620_mt7530_rfb boards supports an external MT7530 giga switch and a
16MB SPI-NOR flash.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:52 +0000 (16:35 +0800)]
mips: mtmips: add support for MediaTek MT7620 SoC
This patch adds support for MediaTek MT7620 SoC.
All files are dedicated for u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:43 +0000 (16:35 +0800)]
mips: mtmips: add support to initialize SDRAM
This patch adds support for mtmips SoCs to initialize the SDRAM.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:38 +0000 (16:35 +0800)]
mips: enable _machine_restart for spl
The sysreset driver has a config CONFIG_SPL_SYSRESET for the spl stage.
Change CONFIG_SYSRESET to CONFIG_IS_ENABLED(SYSRESET) will give spl a
chance to use _machine_restart instead of the sysreset driver.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:33 +0000 (16:35 +0800)]
mips: mtmips: fix dram size detection in dram_init
CONFIG_SYS_SDRAM_BASE points to cached memory, i.e. KSEG0, which is not
suitable for detecting memory size.
Replace CONFIG_SYS_SDRAM_BASE with KSEG1, and make dram_init() always do
memory size detection in any stage.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:28 +0000 (16:35 +0800)]
mips: mtmips: select SYSRESET for mt7628 only
Currently only mt7628 needs the sysreset driver, do not select it for
mt7620.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:23 +0000 (16:35 +0800)]
mips: mtmips: move mt7628 related Kconfig into mt7628 subdirectory
This patch is a preparation for add a new soc fot mtmips.
Move all mt7628 related Kconfig (boards and UART selection) into mt7628
subdirectory and make sure the top directory of mtmips contains only
selection for SoCs.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Weijie Gao [Thu, 12 Nov 2020 08:35:17 +0000 (16:35 +0800)]
mips: dts: switch to board defines for dtb for mtmips
Previous the dts files for gardena-smart-gateway-mt7688 and
linkit-smart-7688 are set to be built when mtmips is selected.
This can lead to a compilation error if another soc is added to this arch
with different dtsi files.
So it's better to build the dtb only if their board is selected.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tom Rini [Sun, 24 Jan 2021 00:07:00 +0000 (19:07 -0500)]
Merge tag 'efi-2021-04-rc1-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-04-rc1-3
Bug fixes for UEFI sub-system:
* correct value of EFI_BLOCK_IO_PROTOCOL.Media.LastBlock
* correct GUID when closing of EFI_LOAD_FILE_PROTOCOL
* error handling in mkeficapsule tool
Bug fixes for FAT file system:
* consistent error handling for flush dir()
Tom Rini [Sat, 23 Jan 2021 17:51:37 +0000 (12:51 -0500)]
Revert "doc: update Kernel documentation build system"
Unfortunately we now see a number of now-fatal warnings about duplicate
labels. It is often unclear how best to re-write the document in
question to not duplicate these otherwise logical headings.
This reverts commit
10a1df3cd43ba2fe893d5dd1aeb2e7109ef0007f.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 23 Jan 2021 14:55:35 +0000 (09:55 -0500)]
Merge branch '2021-01-22-tool-updates'
- Assorted updates to the tools/ code
Tom Rini [Sat, 23 Jan 2021 14:54:02 +0000 (09:54 -0500)]
Merge branch '2021-01-22-doc-updates'
- Assorted documentation updates
Heinrich Schuchardt [Mon, 18 Jan 2021 20:06:03 +0000 (21:06 +0100)]
doc: move README.menu to HTML documentation
Convert README.menu to reStructured text and add it to the HTML
documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 18 Jan 2021 19:24:03 +0000 (20:24 +0100)]
doc: move test/py/README.md to HTML documentation
Convert test/py/README.md to restructured text and add it to the generated
HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Mon, 18 Jan 2021 19:24:02 +0000 (20:24 +0100)]
doc: move test/README to HTML documentation
Move test/README to the 'Develop U-Boot' chapter of the HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Mon, 18 Jan 2021 19:24:01 +0000 (20:24 +0100)]
doc: structure doc/develop/index.rst
Provide sub-chapters for 'Develop U-Boot'
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patrick Delaunay [Thu, 14 Jan 2021 11:04:04 +0000 (12:04 +0100)]
doc: update help message
Update the help message used for 'make help':
Documentation targets:
Linux kernel internal documentation in different formats from ReST:
=>
U-Boot documentation in different formats from ReST:
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Fri, 1 Jan 2021 00:21:11 +0000 (01:21 +0100)]
doc: update Kernel documentation build system
Update the docomentation build system according to Linux v5.11-rc1.
With this patch we can build the HTML documentation using either of
Sphinx 2 and Sphinx 3.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Fix warning in b4860qds.rst about "Switch Settings"]
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 16 Jan 2021 23:17:21 +0000 (00:17 +0100)]
ARM: imx: add i.MX8MN lpddr4 image cfg file
Add cfg file for i.MX8MN LPDDR4
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Adam Ford [Fri, 11 Dec 2020 12:01:46 +0000 (06:01 -0600)]
imx: Add support for i.MX8MN Beacon EmbeddedWorks devkit.
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marc Ferland [Mon, 4 Jan 2021 19:07:53 +0000 (14:07 -0500)]
arm: dart6ul: fix ddr size macro
The previous macro was off by one bit and so we were getting a ddr
size which was twice the real size. This commit refactors the macro so
it returns the right size in _bytes_ and modifies the printf call so the
size is still printed in MiB.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Marek Vasut [Mon, 18 Jan 2021 23:58:33 +0000 (00:58 +0100)]
spi: imx: Use clock framework if enabled
In case the clock framework is enabled, enable the SPI controller clock
and obtain max frequency from the clock framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Mon, 18 Jan 2021 23:58:32 +0000 (00:58 +0100)]
spi: imx: Define register bits in the driver
The CSPI/ECSPI register bits do not differ between newer SoCs, instead
of having multiple copies of the same thing for each iMX SoC, define
the bits in the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Mon, 18 Jan 2021 23:58:31 +0000 (00:58 +0100)]
clk: imx: Add ECSPI to iMX8MN
Add ECSPI clock entries to iMX8MN clock driver. Only make those entries
available in case SPI support in U-Boot is enabled at all to conserve
space, esp. in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Mon, 18 Jan 2021 21:43:09 +0000 (15:43 -0600)]
arm64: dts: imx8mm-beacon: Resync imx8mm-beacon-som with 5.11-rc4
In order to support the QSPI chip on the SOM, the Flexspi bus
needs to be configured to talk with the SPI chip.
Resync the som device tree with 5.11-rc4
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Mon, 18 Jan 2021 21:43:08 +0000 (15:43 -0600)]
imx8mm_beacon: Enable QSPI Support
There is a QSPI chip connected to the FSPI. Enable the defconfig
to support it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Mon, 18 Jan 2021 21:32:50 +0000 (15:32 -0600)]
spi: nxp_fspi: Enable support for nxp,imx8mm-fspi
The i.MX8M Mini can use the FlexSPI driver. Add support
for it to the driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Heiko Schocher [Fri, 15 Jan 2021 09:37:09 +0000 (10:37 +0100)]
mmc: fsl_esdhc_imx.c: fix compiler warning
prevent unsued variable compiler warning if
DM_REGULATOR is not set.
Signed-off-by: Heiko Schocher <hs@denx.de>
Alice Guo [Thu, 14 Jan 2021 08:23:23 +0000 (16:23 +0800)]
imx8mq: configs: add support for distro boot commands
Supported boot device types in iMX8MQ: MMC, DHCP.
CONFIG_DISTRO_DEFAULTS is added for enabling the DISTRO_DEFAULTS option.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mq_evk.h is
deleted because "run distro_bootcmd" is required to be the default boot
mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be
loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables because "run distro_bootcmd" is
set to be the default boot mode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Marek Vasut [Wed, 13 Jan 2021 23:21:22 +0000 (00:21 +0100)]
ARM: imx6: dh-imx6: Move bootcounter to SNVS_LPGDR
Move the bootcounter to SVNS_LPGDR to free up OCRAM for usage by the VPU.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Teresa Remmet [Wed, 13 Jan 2021 15:28:09 +0000 (16:28 +0100)]
board: phytec: imx8mp: Add PHYTEC phyCORE-i.MX8MP support
Add initial support PHYTEC phyCORE-i.MX8MP SOM.
Supported features:
- 2GB LPDDR4 RAM
- eMMC
- external SD
- debug UART2
- watchdog
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Martin Fuzzey [Wed, 13 Jan 2021 10:21:03 +0000 (11:21 +0100)]
w1: mxc: fix build
Now that header files no longer include common.h it must be included
first.
Otherwise the build fails with errors like
include/asm/arch/clock.h:43:1: error: unknown type name 'u32'
u32 imx_get_uartclk(void);
Fixes:
c3dc39a2f85b ("arm: Don't include common.h in header files")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Simon Glass <sjg@chromium.org>
Marc Ferland [Mon, 4 Jan 2021 15:41:57 +0000 (10:41 -0500)]
arm: dart6ul: enable DM_ETH for the dart6ul
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Adam Ford [Wed, 30 Dec 2020 15:15:43 +0000 (09:15 -0600)]
imx: imx8mm-beacon: Remove relocation restrictions
The system is capable of relocating RAM disks and the kernel.
Remove these restrictions to prevent it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Wed, 30 Dec 2020 14:14:19 +0000 (08:14 -0600)]
imx8mm_beacon: Enable fixed regulator in SPL
Because SPL can support SD UHS, the fixed regulator needs to be
enabled in SPL to reset the SD card.
Fixes:
1a5d9c84b472 ("imx8mm_beacon: Enable HS400 on MMC controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Sean Anderson [Mon, 28 Dec 2020 19:58:30 +0000 (14:58 -0500)]
mx6ul(l)evk: Enable DM_ETH_PHY
This fixes eth0 not initializing properly. Both eth0 and eth1 use the
MDIO interface on eth1 to access their PHYs. However, without
DM_ETH_PHY, eth0 still tries to use its own MDIO interface to access its
phy. Before this patch, a boot log might contain lines like
Net:
Warning: ethernet@20b4000 using MAC address from ROM
eth1: ethernet@20b4000 [PRIME]Could not get PHY for FEC0: addr 2
After this patch they now look like
Net:
Warning: ethernet@20b4000 using MAC address from ROM
eth1: ethernet@20b4000 [PRIME]Get shared mii bus on ethernet@2188000
Warning: ethernet@2188000 using MAC address from ROM
, eth0: ethernet@2188000
As an alternative to DM_ETH_PHY, FEC_MXC_SHARE_MDIO could also have been
used to achieve the same effect.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Alice Guo [Fri, 18 Dec 2020 07:19:27 +0000 (15:19 +0800)]
board: imx8mp: add boot.cmd for distro boot on iMX8MP
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value
"/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Signed-off-by: Alice Guo <alice.guo@nxp.com>