review.tizen.org Git - platform/kernel/linux-rpi.git/log

drm/i915/display/ehl: Limit eDP to HBR2

Recent update in documentation defeatured eDP HBR3 for EHL and JSL.

v2:
- Remove dead code in ehl_get_combo_buf_trans()

v3:
- Rebase

BSpec: 32247
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005175447.93430-1-jose.souza@intel.com

drm/i915/tgl: Fix Combo PHY DPLL fractional divider for 38.4MHz ref clock

Apply Display WA #22010492432 for combo PHY PLLs too. This should fix a
problem where the PLL output frequency is slightly off with the current
PLL fractional divider value.

I haven't seen an actual case where this causes a problem, but let's
follow the spec. It's also needed on some EHL platforms, but for that we
also need a way to distinguish the affected EHL SKUs, so I leave that
for a follow-up.

v2:
- Apply the WA at one place when calculating the PLL dividers from the
frequency and the frequency from the dividers for all the combo PLL
use cases (DP, HDMI, TBT). (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003001846.1271151-6-imre.deak@intel.com

drm/i915: Add an encoder hook to sanitize its state during init/resume

Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.

A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.

The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3

v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.

v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com

drm/i915: Check for unsupported DP link rates during initial commit

Some BIOSes set an unsupported/imprecise DP link rate (for instance on
TGL A stepping). Make sure that we do an encoder recompute and a modeset
in this case.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003001846.1271151-4-imre.deak@intel.com

drm/i915: Move the initial fastset commit check to encoder hooks

Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.

v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com

drm/i915/skl: Work around incorrect BIOS WRPLL PDIV programming

The BIOS of at least one ASUS-Z170M system with an SKL I have programs
the 101b WRPLL PDIV divider value, which is the encoding for PDIV=7 with
bit#0 incorrectly set.

This happens with the

"3840x2160": 30 262750 3840 3888 3920 4000 2160 2163 2168 2191 0x48 0x9

HDMI mode (scaled from a 1024x768 src fb) set by BIOS and the

ref_clock=24000, dco_integer=383, dco_fraction=5802, pdiv=7, qdiv=1, kdiv=1

WRPLL parameters (assuming PDIV=7 was the intended setting). This
corresponds to 262749 PLL frequency/port clock.

Later the driver sets the same mode for which it calculates the same
dco_int/dco_frac/div WRPLL parameters (with the correct PDIV=7 encoding).

Based on the above, let's assume that PDIV=7 was intended and the HW
just ignores bit#0 in the PDIV register field for this setting, treating
100b and 101b encodings the same way.

While at it add the MISSING_CASE() for the p0,p2 divider decodings.

v2: (Ville)
- Add a define for the incorrect divider value.
- Emit only a debug message when detecting the incorrect divider value.
- Use fallthrough from the incorrect divider value case.
- Add the MISSING_CASE()s.

v3: Return 0 freq for incorrect divider values. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006013555.1488262-1-imre.deak@intel.com

drm/i915/dg1: Wait for pcode/uncore handshake at startup

DG1 does some additional pcode/uncore handshaking at
boot time; this handshaking must complete before various other pcode
commands are effective and before general work is submitted to the GPU.
We need to poll a new pcode mailbox during startup until it reports that
this handshaking is complete.

The bspec doesn't give guidance on how long we may need to wait for this
handshaking to complete. For now, let's just set a really long timeout;
if we still don't get a completion status by the end of that timeout,
we'll just continue on and hope for the best.

v2 (Lucas): Rename macros to make clear the relation between command and
result (requested by José)

Bspec: 52065
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001063917.3133475-2-lucas.demarchi@intel.com

drm/i915: don't conflate is_dgfx with fake lmem

When using fake lmem for tests, we are overriding the setting in
device info for dgfx devices. Current users of IS_DGFX() except one are
correct. However, as we add support for DG1, we are going to use it in
additional places to trigger dgfx-only code path.

In future if we need we can use HAS_LMEM() instead of IS_DGFX() in the
places that make sense to also contemplate fake lmem use.

v2: update gen8_gmch_probe() to use HAS_LMEM(): we need to steal the
mappable aperture later(which is fine since it doesn't exist on "DGFX"),
and use it as a substitute for LMEMBAR. The !mappable aperture property
is also useful since it exercises some other parts of the code too.
(Matthew Auld)

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001063917.3133475-1-lucas.demarchi@intel.com

drm/i915: Make lspcon_init() static

Make lspcon_init() static since it's no longer needed outside
the compilation unit. This was correct in Kai-Heng's lspcon
patch, but I fumbled this when applying it.

Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: f542d671ffce ("drm/i915: Init lspcon after HPD in intel_dp_detect()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002090446.21104-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Init lspcon after HPD in intel_dp_detect()

On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[ 3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[ 3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D

Seems like the lspcon chip on the system only gets powered after the
cable is plugged.

Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.

v6:
- Rebase on latest for-linux-next.
v5:
- Consolidate lspcon_resume() with lspcon_init().
- Move more logic into lspcon code.
v4:
- Trust VBT in intel_infoframe_init().
- Init lspcon in intel_dp_detect().
v3:
- Make sure it's handled under long HPD case.
v2:
- Move lspcon_init() inside of intel_dp_hpd_pulse().

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com

drm/i915: Eliminate intel_dp.regs.dp_tp_{ctl,status}

Now that we've plumbed the crtc state all the way down we can
eliminate the DP_TP_{CTL,STATUS} register offsets from intel_dp,
and instead we derive them directly from the crtc state.

And thus we can get rid of the nasty hack in intel_ddi_get_config()
which mutates intel_dp during the readout.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Plumb crtc_state to link training

Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.

Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.

v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)

Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com

drm/i915: Split TGL DKL PHY buf trans per output type

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-10-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Split TGL combo PHY buf trans per output type

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-9-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Split EHL combo PHY buf trans per output type

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-8-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Split ICL MG PHY buf trans per output type

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Split ICL combo PHY buf trans per output type

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-6-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Shove the PHY test into the hotplug work

Doing any kind modeset stuff from the short hpd handler is
verboten. The ad-hoc PHY test modeset code violates this. And
by calling various link training related functions it's now
blocking further work to plumb the crtc state down into the
link training code.

Let's hack around that by pushing the PHY test stuff into the
hotplug work where it's less of a problem. Still not great but
at least acceptable. We take a few pages from the link retraining
handbook to handle the locking and whatnot.

v2: Fix the intel_dp_hotplug() return value

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930100412.9313-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Make intel_dp_process_phy_request() static

intel_dp_process_phy_request() has no business being externally
visible. Make it static.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: s/old_crtc_state/crtc_state/

intel_dp_enable_port() is called during the enable sequence,
so there is nothing old about the passed in crtc state.
Rename it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: s/pre_empemph/preemph/

I managed to fumble some functions names. Fix them.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915: Fix TGL DKL PHY DP vswing handling

The HDMI vs. not-HDMI check got inverted whem the bogus encoder->type
checks were eliminated. So now we're using 0 as the link rate on DP
and potentially non-zero on HDMI, which is exactly the opposite of
what we want. The original bogus check actually worked more correctly
by accident since if would always evaluate to true. Due to this we
now always use the RBR/HBR1 vswing table and never ever the HBR2+
vswing table. That is probably not a good way to get a high quality
signal at HBR2+ rates. Fix the check so we pick the right table.

Cc: stable@vger.kernel.org
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 94641eb6c696 ("drm/i915/display: Fix the encoder type check")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930223642.28565-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>

drm/i915: Implement display WA #1142:kbl,cfl,cml

Implement display w/a #1142. This supposedly fixes some underruns
with FBC+VTd. Bspec says we should use the same programming regardless
of circumstances. Apparently we should flip the magic bits before
turning on any planes so let's put this into the early w/as.

Cc: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924194810.10293-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Read DIMM size in Gb rather than GB

CNL+ can report DIMM sizes in .5 GB units. In order to not trauncate
away the .5 GB let's switch to storing the DIMM size in Gb units.

Cc: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929131312.12999-1-ville.syrjala@linux.intel.com

drm/i915/dsi: Enable software vblank counter

In case of DSI cmd mode, we get hw vblank counter updated after the TE
comes in, if we try to read the hw vblank counter in te handler we
wouldnt have the udpated vblank counter yet. This will lead to a state
where we would send the vblank event to the user space in the next te,
though the frame update would have completed in the first TE duration
itself. Hence switch to using software timestamp based vblank counter.

v2: Use mode_flags from crtc_state (Ville)

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924124209.17916-6-vandita.kulkarni@intel.com

drm/i915/dsi: Initiate frame request in cmd mode

In TE Gate mode or TE NO_GATE mode on every flip we need to set the
frame update request bit. After this bit is set transcoder hardware will
automatically send the frame data to the panel in case of TE NO_GATE
mode, where it sends after it receives the TE event in case of TE_GATE
mode. Once the frame data is sent to the panel, we see the frame counter
updating.

v2: Use intel_de_read/write

v3: remove the usage of private_flags

v4: Use icl_dsi in func names if non static,
fix code formatting issues. (Jani)

v5: Send frame update request at the beginning of
pipe_update_end, use crtc_state mode_flags (Ville)

v6: Add platform and dsi checks (Ville)

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200928110834.15077-1-vandita.kulkarni@intel.com

drm/i915/dsi: Add TE handler for dsi cmd mode.

In case of dual link, we get the TE on slave. So clear the TE on slave
DSI IIR.

If we are operating in TE_GATE mode, after we do a frame update, the
transcoder will send the frame data to the panel, after it receives a
TE. Whereas if we are operating in NO_GATE mode then the transcoder will
immediately send the frame data to the panel. We are not dealing with
the periodic command mode here.

v2: Pass only relevant masked bits to the handler (Jani)

v3: Fix the check for cmd mode in TE handler function.

v4: Use intel_handle_vblank instead of drm_handle_vblank (Jani)

v3: Use static on handler func (Jani)

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924124209.17916-4-vandita.kulkarni@intel.com

i915/dsi: Configure TE interrupt for cmd mode

Configure TE interrupt as part of the vblank enable call flow.

v2: Hide the private flags check inside configure_te (Jani)

v3: Fix the position of masking de_port_masked for DSI_TE.

v4: Simplify the caller of configure_te (Jani)

v5: Clear IIR, remove the usage of private_flags

v6: including icl_dsi header is not needed

Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924124209.17916-3-vandita.kulkarni@intel.com

drm/i915/dsi: Add details about TE in get_config

We need details about enabling TE on which port before we enable TE
through vblank enable path. This is based on the configuration that we
receive from the VBT wrt ports, dual_link.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924124209.17916-2-vandita.kulkarni@intel.com

drm/i915: Replace some gamma_mode ifs with switches

Since gamma_mode can have more than two values on ilk+
let's use switch statements when interpreting them.

v2: Fix typo (Uma)

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-10-ville.syrjala@linux.intel.com

drm/i915: Polish bdw_read_lut_10() a bit

Since bdw_read_lut_10() uses the auto-increment mode we must
have an equal number of entries in the software LUT and the
hardware LUT. WARN if that is not the case.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-9-ville.syrjala@linux.intel.com

drm/i915: Relocate CHV CGM gamma masks

CGM_PIPE_GAMMA_RED_MASK & co. are misplaced. Move then below the
relevant register. And while at it add the degamma counterparts.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-8-ville.syrjala@linux.intel.com

drm/i915: Shuffle chv_cgm_gamma_pack() around a bit

Move chv_cgm_gamma_pack() next to the other CGM gamma functions.
Right now it's stuck in the middle of the CGM degamma functions.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-7-ville.syrjala@linux.intel.com

drm/i915: Reset glk degamma index after programming/readout

Just for some extra consistency let's reset the glk degamma LUT
index back to 0 after we're dong trawling the LUT.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-6-ville.syrjala@linux.intel.com

drm/i915: s/glk_read_lut_10/bdw_read_lut_10/

glk_read_lut_10() works just fine for all bdw+ platforms, so
rename it.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-5-ville.syrjala@linux.intel.com

drm/i915: Include the LUT sizes in the state dump

Dump the sizes of the software LUTs in the state dump. Makes
it a bit easier to see which is present without having to
decode it from the gamma_mode and other bits of state.

v2: Drop a spurious "is" in commit msg (Uma)

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-4-ville.syrjala@linux.intel.com

drm/i915: Move MST master transcoder dump earlier

Move the MST master transcoder dump next to the other transcoder
bits.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-3-ville.syrjala@linux.intel.com

drm/i915: Fix state checker hw.active/hw.enable readout

Previously intel_dump_pipe_config() used to dump the full crtc state
whether or not the crtc was logically enabled or not. As that meant
occasionally dumping confusing stale garbage I changed it to
check whether the crtc is logically enabled or not. However I did
not realize that the state checker readout code does not
populate crtc_state.hw.{active,enabled}. Hence the state checker
dump would only give us a full dump of the sw state but not the hw
state. Fix that by populating those bits of the hw state as well.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Fixes: 10d75f5428fd ("drm/i915: Fix plane state dumps")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925131656.10022-2-ville.syrjala@linux.intel.com

drm/i915: Don't hide the intel_crtc_atomic_check() call

Move the intel_crtc_atomic_check() call out from the variable
declarations to a place where we can actually see it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925121749.708-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Make intel_{enable,disable}_sagv() static

intel_{enable,disable}_sagv() are no longer needed outside the
compilation unit. Make them static.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200925121749.708-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Enable async flips in i915

Enable asynchronous flips in i915 for gen9+ platforms.

v2: -Async flip enablement should be a stand alone patch (Paulo)

v3: -Move the patch to the end of the series (Paulo)

v4: -Rebased.

v5: -Rebased.

v6: -Rebased.

v7: -Rebased.

v8: -Rebased.

v9: -Rebased.

v10: -Rebased.

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-9-karthik.b.s@intel.com

Documentation/gpu: Add asynchronous flip documentation for i915

Add the details of the implementation of asynchronous flips for i915.

v7: -Rebased.

v8: -Rebased.

v9: -Rebased.

v10: Move all documentation changes to this patch. (Ville)

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-8-karthik.b.s@intel.com

drm/i915: WA for platforms with double buffered address update enable bit

In Gen 9 and Gen 10 platforms, async address update enable bit is
double buffered. Due to this, during the transition from async flip
to sync flip we have to wait until this bit is updated before continuing
with the normal commit for sync flip.

v9: -Rename skl_toggle_async_sync() to skl_disable_async_flip_wa(). (Ville)
    -Place the declarations appropriately as per need. (Ville)
    -Take the lock before the reg read. (Ville)
    -Fix comment and formatting. (Ville)
    -Use IS_GEN_RANGE() for gen check. (Ville)
    -Move skl_disable_async_flip_wa() to intel_pre_plane_update(). (Ville)

v10: -Rebased.

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-7-karthik.b.s@intel.com

drm/i915: Add dedicated plane hook for async flip case

This hook is added to avoid writing other plane registers in case of
async flips, so that we do not write the double buffered registers
during async surface address update.

v7: -Plane ctl needs bits from skl_plane_ctl_crtc as well. (Ville)
    -Add a vfunc for skl_program_async_surface_address
     and call it from intel_update_plane. (Ville)

v8: -Rebased.

v9: -Use if-else instead of return in intel_update_plane(). (Ville)
    -Rename 'program_async_surface_address' to 'async_flip'. (Ville)

v10: -Check if async_flip hook is present before calling it.
      Otherwise it will OOPS during legacy cursor updates. (Ville)

v11: -Rename skl_program_async_surface_address(). (Ville)

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-6-karthik.b.s@intel.com

drm/i915: Do not call drm_crtc_arm_vblank_event in async flips

Since the flip done event will be sent in the flip_done_handler,
no need to add the event to the list and delay it for later.

v2: -Moved the async check above vblank_get as it
was causing issues for PSR.

v3: -No need to wait for vblank to pass, as this wait was causing a
16ms delay once every few flips.

v4: -Rebased.

v5: -Rebased.

v6: -Rebased.

v7: -No need of irq disable if we are not doing vblank evade. (Ville)

v8: -Rebased.

v9: -Move the return in intel_pipe_update_end before tracepoint. (Ville)

v10: Rebased.

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-5-karthik.b.s@intel.com

drm/i915: Add checks specific to async flips

If flip is requested on any other plane, reject it.

Make sure there is no change in fbc, offset and framebuffer modifiers
when async flip is requested.

If any of these are modified, reject async flip.

v2: -Replace DRM_ERROR (Paulo)
    -Add check for changes in OFFSET, FBC, RC(Paulo)

v3: -Removed TODO as benchmarking tests have been run now.

v4: -Added more state checks for async flip (Ville)
    -Moved intel_atomic_check_async to the end of intel_atomic_check
     as the plane checks needs to pass before this. (Ville)
    -Removed crtc_state->enable_fbc check. (Ville)
    -Set the I915_MODE_FLAG_GET_SCANLINE_FROM_TIMESTAMP flag for async
     flip case as scanline counter is not reliable here.

v5: -Fix typo and other check patch errors seen in CI
     in 'intel_atomic_check_async' function.

v6: -Don't call intel_atomic_check_async multiple times. (Ville)
    -Remove the check for n_planes in intel_atomic_check_async
    -Added documentation for async flips. (Paulo)

v7: -Replace 'intel_plane' with 'plane'. (Ville)
    -Replace all uapi.foo as hw.foo. (Ville)
    -Do not use intel_wm_need_update function. (Ville)
    -Add destination coordinate check. (Ville)
    -Do not allow async flip with linear buffer
     on older hw as it has issues with this. (Ville)
    -Remove break after intel_atomic_check_async. (Ville)

v8: -Rebased.

v9: -Replace DRM_DEBUG_KMS with drm_dbg_kms(). (Ville)
    -Fix comment formatting. (Ville)
    -Remove gen specific checks. (Ville)
    -Remove irrelevant FB size check. (Ville)
    -Add missing stride check. (Ville)
    -Use drm_rect_equals() instead of individual checks. (Ville)
    -Call intel_atomic_check_async before state dump. (Ville)

v10: -Fix the checkpatch errors seen on CI.

v11: -Use const for all plane/crtc states. (Ville)
     -Use 'switch' instead of 'if' for modifier check. (Ville)
     -Move documentation changes to a single patch. (Ville)

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-4-karthik.b.s@intel.com

drm/i915: Add support for async flips in I915

Set the Async Address Update Enable bit in plane ctl
when async flip is requested.

v2: -Move the Async flip enablement to individual patch (Paulo)

v3: -Rebased.

v4: -Add separate plane hook for async flip case (Ville)

v5: -Rebased.

v6: -Move the plane hook to separate patch. (Paulo)
-Remove the early return in skl_plane_ctl. (Paulo)

v7: -Move async address update enable to skl_plane_ctl_crtc() (Ville)

v8: -Rebased.

v9: -Rebased.

v10: -Rebased.

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-3-karthik.b.s@intel.com

drm/i915: Add enable/disable flip done and flip done handler

Add enable/disable flip done functions and the flip done handler
function which handles the flip done interrupt.

Enable the flip done interrupt in IER.

Enable flip done function is called before writing the
surface address register as the write to this register triggers
the flip done interrupt

Flip done handler is used to send the page flip event as soon as the
surface address is written as per the requirement of async flips.
The interrupt is disabled after the event is sent.

v2: -Change function name from icl_* to skl_* (Paulo)
    -Move flip handler to this patch (Paulo)
    -Remove vblank_put() (Paulo)
    -Enable flip done interrupt for gen9+ only (Paulo)
    -Enable flip done interrupt in power_well_post_enable hook (Paulo)
    -Removed the event check in flip done handler to handle async
     flips without pageflip events.

v3: -Move skl_disable_flip_done out of interrupt handler (Paulo)
    -Make the pending vblank event NULL in the beginning of
     flip_done_handler to remove sporadic WARN_ON that is seen.

v4: -Calculate timestamps using flip done time stamp and current
     timestamp for async flips (Ville)

v5: -Fix the sparse warning by making the function 'g4x_get_flip_counter'
     static.(Reported-by: kernel test robot <lkp@intel.com>)
    -Fix the typo in commit message.

v6: -Revert back to old time stamping code.
    -Remove the break while calling skl_enable_flip_done. (Paulo)

v7: -Rebased.

v8: -Rebased.

v9: -Use struct drm_i915_private *i915 in new code. (Ville)
    -Use intel_crtc instead of drm_crtc. (Ville)
    -Do not mix the flip done and vblank hooks. (Ville)

v10: -Rebased.

Signed-off-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200921110210.21182-2-karthik.b.s@intel.com

drm/i915: Use the correct bpp when validating "4:2:0 only" modes

When validating a "YCbCr 4:2:0 only" mode we must take into
account the fact that we're going to be outputting YCbCr
4:2:0 or 4:4:4 (when a DP->HDMI protocol converter is doing
the 4:2:0 downsampling). For YCbCr 4:4:4 the minimum output
bpc is 8, for YCbCr 4:2:0 it'll be half that. The currently
hardcoded 6bpc is only correct for RGB 4:4:4, which we will
never use with these kinds of modes. Figure out what we're
going to output and use the correct min bpp value to validate
whether the link has sufficient bandwidth.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917214335.3569-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>

drm/i915: Decouple intel_dp_{min,output}_bpp() from crtc_state

Pass the output_format directly to intel_dp_{min,output}_bpp()
rather than passing in the crtc_state and digging out the
output_format inside the functions. This will allow us to reuse
the functions for mode validation purposes.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917214335.3569-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>

drm/i915: Extract intel_dp_output_format()

Refactor the output_format calculation into a helper so that
we can reuse it for mode validation as well.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917214335.3569-1-ville.syrjala@linux.intel.com
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>

drm/i915: dont retry stream management at seq_num_m roll over

When roll over detected for seq_num_m, we shouldn't continue with stream
management with rolled over value.

So we are terminating the stream management retry, on roll over of the
seq_num_m.

v2:
  using drm_dbg_kms instead of DRM_DEBUG_KMS [Anshuman]
v3:
  dev_priv is used as i915 [JaniN]
v4:
  roll over is detected at the start of the stream management.

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> [v3]
Tested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923132435.17039-3-anshuman.gupta@intel.com

drm/i915: terminate reauth at stream management failure

As per the HDCP2.2 compliance test 1B-10 expectation, when stream
management for a repeater fails, we retry thrice and when it fails
in all retries, HDCP2.2 reauthentication aborted at kernel.

v2:
  seq_num_m++ is extended for steam management failures too.[Anshuman]
v3:
  use drm_dbg_kms instead of DRM_DEBUG_KMS [Anshuman]
v4:
  dev_priv is used as i915 [JaniN]
v5:
  Few improvisements are done [Sean]

Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923132435.17039-2-anshuman.gupta@intel.com

drm/dp: fix a kernel-doc issue at drm_edid.c

The name of the argument is different, causing those warnings:

./drivers/gpu/drm/drm_edid.c:3754: warning: Function parameter or member 'video_code' not described in 'drm_display_mode_from_cea_vic'
./drivers/gpu/drm/drm_edid.c:3754: warning: Excess function parameter 'vic' description in 'drm_display_mode_from_cea_vic'

Fixes: 7af655bce275 ("drm/dp: Add drm_dp_downstream_mode()")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200922175357.42998-3-lyude@redhat.com

drm/dp: fix kernel-doc warnings at drm_dp_helper.c

As warned by kernel-doc:

./drivers/gpu/drm/drm_dp_helper.c:385: warning: Function parameter or member 'type' not described in 'drm_dp_downstream_is_type'
./drivers/gpu/drm/drm_dp_helper.c:886: warning: Function parameter or member 'dev' not described in 'drm_dp_downstream_mode'

Some function parameters weren't documented.

Fixes: 38784f6f8805 ("drm/dp: Add helpers to identify downstream facing port types")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200922175357.42998-2-lyude@redhat.com

drm/i915: Update DRIVER_DATE to 20200917

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/tgl, rkl: Make Wa_1606700617/22010271021 permanent

This workaround applies to all TGL and RKL steppings.

Signed-off-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200911221158.4700-1-swathi.dhanavanthri@intel.com

drm/i915: Nuke force_min_cdclk_changed

Since we now have proper old and new cdclk state we no longer
need to keep this flag to indicate that the force min cdclk has
changed. Instead just check if the old vs. new value are different.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714152626.380-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

drm/i915: Remove the old global state stuff

With the dbuf code mostly converted over to the new global state
handling we can remove the leftovers of the old global state
stuff.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200902122141.15181-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

drm/i915: Do YCbCr 444->420 conversion via DP protocol converters

For platforms that can't do native 4:2:0 outout we may still be
able to do it by getting the DP->HDMI protocol converter to
perform the 4:4:4->4:2:0 downsamling for us. In this case we
have to configure our hardware to output YCbCr 4:4:4, which we've
already hooked up so all we need to do is flip the switch.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-19-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Add helpers for DFP YCbCr 4:2:0 handling

Add helpers to determine whether the DFP supports
YCbCr 4:2:0 passthrough or YCbCr 4:4:4->4:2:0 conversion.

v2: Add kdocs (Lyude)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-18-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: DP->HDMI TMDS clock limits vs. deep color

Account for the TMDS clock limits declared by the DFP
when determining what color depth we're going to use.

v2: Drop the reference to DP++ dongle since it's not handled here

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-17-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Extract intel_hdmi_has_audio()

Pull the "do we want to enable audio?" computation into a small helper
to make intel_hdmi_compute_config() less messy. Will make it easier to
add more checks for this later (eg. we should actually be checking
at the hblank is long enough for audio transmission).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-16-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Handle downstream facing ports w/o EDID

Use drm_dp_downstream_mode() to get a suitable mode for downstream
facing ports which don't have an EDID.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-15-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Add drm_dp_downstream_mode()

The downstream facing port caps in the DPCD can give us a hint
as to what kind of display mode the sink can use if it doesn't
have an EDID. Use that information to pick a suitable mode.

v2: Use Returns: for kdoc (Lyude)
Add kdocs for drm_display_mode_from_cea_vic() (Lyude)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-14-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Configure DP 1.3+ protocol converted HDMI mode

DP 1.3 adds some extra control knobs for DP->HDMI protocol conversion.
Let's use that to configure the "HDMI mode" (ie. infoframes vs. not)
based on the capabilities of the sink.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-13-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Deal with TMDS DFP clock limits

Use the new helpers to extract the TMDS clock limits from
the downstream facing port and check them in .mode_valid().

TODO: we should check these in .compute_config() too to eg.
determine if we can do deep color on the HDMI side or not

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-12-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Add drm_dp_downstream_{min,max}_tmds_clock()

Add helpers to get the TMDS clock limits for HDMI/DVI downstream
facing ports.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-11-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Reworkd DP DFP clock handling

Move the downstream facing port dotclock check into a new function
(intel_dp_mode_valid_downstream()) so that we have a nice future
place where we can collect other related checks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-10-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Redo drm_dp_downstream_max_clock() as drm_dp_downstream_max_dotclock()

We want to differentiate between the DFP dotclock and TMDS clock
limits. Let's convert the current thing to just give us the
dotclock limit.

v2: Use Returns: for kdoc (Lyude)
Fix up nouveau code too

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-9-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Pimp drm_dp_downstream_max_bpc()

Deal with more cases in drm_dp_downstream_max_bpc():
- DPCD 1.0 -> assume 8bpc for non-DP
- DPCD 1.1+ DP (or DP++ with DP sink) -> allow anything
- DPCD 1.1+ TMDS -> check the caps, assume 8bpc if the value is crap
- anything else -> assume 8bpc

v2: Use Returns: for kdoc (Lyude)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-8-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Add helpers to identify downstream facing port types

Add a few helpers to let us better identify which kind of DFP
we're dealing with.

v2: Use Returns: for kdoc (Lyude)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-7-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Reworkd DFP max bpc handling

Stash the downstream facing port max bpc away during
intel_dp_set_edid(). We'll soon need the EDID in there so
we can't figure this out so easily during .compute_config() anymore.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-6-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Define more downstream facing port caps

Our definitions for the DPCD DFP capabilities are lacking.
Add the missing bits.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-5-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Define protocol converter DPCD registers

DP 1.3 and 1.4 introduced some new registers for DP->HDMI protocol
converters. Define those.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-4-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/lspcon: Do not send infoframes to non-HDMI sinks

Non-HDMI sinks shouldn't be sent infoframes. Check for that when
using LSPCON.

FIXME: How do we turn off infoframes once enabled? Do we even
have to?

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-3-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/dp: Dump downstream facing port caps

It helps when the logs have a dump of the DFP capabilities.

v2: Move the dumping to the new helper

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-2-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915/selftests: Push the fake iommu device from the stack to data

Since we store a pointer to the fake iommu device that is allocated on
the stack, as soon as we leave the function it goes out of scope and any
future dereference is undefined behaviour. Just in case we may need to
look at the fake iommu device after initialiation, move the allocation
from the stack into the data.

Fixes: 01b9d4e21148 ("iommu/vt-d: Use dev_iommu_priv_get/set()")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200916105022.28316-2-chris@chris-wilson.co.uk

drm/i915: Initialise outparam for error return from wait_for_register

Just in case the caller passes in 0 for both slow&fast timeouts, make
sure we initialise the stack value returned. Add an assert so that we
don't make the mistake of passing 0 timeouts for the wait.

drivers/gpu/drm/i915/intel_uncore.c:2011 __intel_wait_for_register_fw() error: uninitialized symbol 'reg_value'.

References: 3f649ab728cd ("treewide: Remove uninitialized_var() usage")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200916105022.28316-1-chris@chris-wilson.co.uk

drm/i915/pll: Centralize PLL_ENABLE register lookup

We currenty check for platform at multiple parts in the driver
to grab the correct PLL. Let us begin to centralize it through a
helper function.

v2: s/intel_get_pll_enable_reg()/intel_combo_pll_enable_reg() (Ville)

v3: Clean up combo_pll_disable() (Rodrigo)

v4: s/dev_priv/i915 (Jani)
Move static and return type to the same line( Ville, Jani)

Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200914175703.15024-1-anusha.srivatsa@intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Nuke pointless variable

No point in assigning the function return value to a local
variable if we're just going to use it the one time.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Introduce intel_hpd_hotplug_irqs()

Introduce intel_hpd_hotplug_irqs() as a partner to
intel_hpd_enabled_irqs(). There's no need to care about the
encoders which we're not exposing, so we can avoid hardcoding
the masks in various places.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-12-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Introduce HPD_PORT_TC<n>

Make a clean split between hpd pins for DDI vs. TC. This matches
how the actual hardware is split.

And with this we move the DDI/PHY->HPD pin mapping into the encoder
init instead of having to remap yet again in the interrupt code.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Move hpd_pin setup to encoder init

Currently DP/HDMI/DDI encoders init their hpd_pin from the
connector init. Let's move it to the encoder init so that
we don't need to add platform specific junk to the connector
init (which is shared by all g4x+ platforms).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-10-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Split icp_hpd_detection_setup() into ddi vs. tc parts

No reason to stuff both DDI and TC port handling into the same
function. Split it into two.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-9-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Configure GEN11_{TBT,TC}_HOTPLUG_CTL for ports TC5/6

gen11_hpd_detection_setup() is missing ports TC5/6. Add them.

TODO: Might be nice to only enable the hpd detection logic
for ports we actually have. Should be rolled out for all
platforms if/when done...

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-8-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Nuke the redundant TC/TBT HPD bit defines

We have nice parametrized GEN11_{TC,TBT}_HOTPLUG() so nuke
the overlapping defines.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-7-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Add VBT AUX CH H and I

As with everything else VBT can now specify AUX CH H or I.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-6-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Add VBT DVO ports H and I

VBT has ports H and I since version 217.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Add AUX_CH_{H,I} power domain handling

AUX CH H/I need their power domains too.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Add PORT_{H,I} to intel_port_to_power_domain()

We need to go up to PORT_I (aka. TC6) these days.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Add more AUX CHs to the enum

We need to go up to AUX_CH_I (aka. AUX CH USBC6) these days.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915: Reduce INTEL_DISPLAY_ENABLED to just treat outputs as disconnected

Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.

v2: Put the check into the right place for CRT

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Reduce INTEL_DISPLAY_ENABLED to just removing the outputs

Having a mode where the display hardware is present but we try
to pretend it isn't just leads to massive headaches when trying
to reason what the fallout might be from skipping some random
bits of programming.

Let's just neuter INTEL_DISPLAY_ENABLED so that we treat the
hardware as fully present, except we just don't register any
outputs. That's still rather sketchy if the outputs are already
enabled when the driver is loaded. I think the simplest solution
would be to probe everything as normal and just return
disconnected" from all .detect() hooks. That would avoid anything
automagically enabling those outputs, but the driver could then
shut things down using the normal codepaths.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200909213824.12390-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Update DRIVER_DATE to 20200914

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Merge tag 'gvt-next-2020-09-10' of https://github.com/intel/gvt-linux into drm-intel-next-queued

gvt-next-2020-09-10

- Cleanup command access flag (Yan)
- New workaround cmd access fix (Colin)
- MIA reset state fix (Colin)

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910053720.GK28614@zhen-hp.sh.intel.com

drm/i915: Use fb->format->is_yuv for the g4x+ sprite RGB vs. YUV check

g4x+ sprites have an extra cdclk limitation listed for RGB formats.
For some random reason I chose to use cpp>=4 as the check for that.
While that does actually work let's deobfuscate it by checking
for !is_yuv instead. I suspect is_yuv didn't exist way back when
I originally write the code.

Also drop the duplicate comment.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206201204.31704-2-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix g4x+ sprite dotclock limit for upscaling

Even if we're not doing downscaling we should account for
some of the extra dotclock limitations for g4x+ sprites. In
particular we must never exceed the 90% rule, and with RGB
that limits actually drops to 80%.

So instead of bailing out when upscaling let's clamp the
scaling factor appropriately and go through the rest of
calculation normally. By luck we already did the full
calculations for the 1:1 case.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200206201204.31704-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>