Marek Vasut [Fri, 25 Feb 2022 01:15:59 +0000 (02:15 +0100)]
stm32mp: psci: Implement PSCI system suspend and DRAM SSR
Implement PSCI system suspend and placement of DRAM into SSR while the
CPUs are in suspend. This saves non-trivial amount of power in suspend,
on 2x W632GU6NB-15 ~710mW.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Fri, 25 Feb 2022 01:15:58 +0000 (02:15 +0100)]
ram: stm32mp1: Unconditionally enable ASR
Enable DRAM ASR, auto self-refresh, unconditionally. This saves non-trivial
amount of power both at runtime and in suspend (on 2x W632GU6NB-15 ~150mW).
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Thu, 3 Feb 2022 01:49:29 +0000 (02:49 +0100)]
ARM: dts: stm32: Move vdd_io extras into Avenger96 extras
The vdd_io regulator is present only on DHCOR SoM configured for 1V8 IO,
as populated on Avenger96, but not present on 3V3 DHCOR SoM. Move these
extras to Avenger96 u-boot DT extras.
Fixes:
3919aa1722a ("ARM: dts: stm32: Add DFU support for DHCOR recovery")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Fri, 28 Jan 2022 18:35:20 +0000 (19:35 +0100)]
ARM: dts: stm32: Add USB OTG pinctrl and regulator nodes into SPL DT on DHCOR
Fix the following warning in SPL and make sure that even DTs which
enforce Vbus detection using u-boot,force-vbus-detection;, the DFU
in SPL will work.
dwc2-udc-otg usb-otg@
49000000: prop pinctrl-0 index 0 invalid phandle
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Mon, 31 Jan 2022 15:07:54 +0000 (16:07 +0100)]
arm: dts: stm32mp15: alignment with v5.17
Device tree alignment with Linux kernel v5.17-rc1
- ARM: dts: stm32: add pull-up to USART3 and UART7 RX pins
on STM32MP15 DKx boards
- ARM: dts: stm32: clean uart4_idle_pins_a node for stm32mp15
- ARM: dts: stm32: tune the HS USB PHYs on stm32mp15xx-dkx
- ARM: dts: stm32: tune the HS USB PHYs on stm32mp157c-ev1
- ARM: dts: stm32: fix stusb1600 pinctrl used on stm32mp157c-dk
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Gabriel Fernandez [Tue, 1 Feb 2022 13:02:14 +0000 (14:02 +0100)]
video: stm32: stm32_ltdc: fix the check of return value of clk_set_rate()
The clk_set_rate() function returns rate as an 'ulong' not
an 'int' and rate > 0 by default.
This patch avoids to display the associated warning when
the set rate function returns the new frequency.
Fixes:
aeaf330649e8 ("video: stm32: stm32_ltdc: add bridge to display controller")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 1 Feb 2022 13:37:19 +0000 (14:37 +0100)]
board: st: common: update test on misc_read result in command stboard
Update management of misc_read/misc_write, which now returns length of
data after the commit
8729b1ae2cbd ("misc: Update read() and write()
methods to return bytes xfered"): raise a error when the result is not
the expected length.
Fixes:
658fde8a36ff ("board: stm32mp1: stboard: lock the OTP after programming")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 15 Feb 2022 15:08:51 +0000 (16:08 +0100)]
stm32mp1: bsec: add missing dev in function comment
Add the missing @dev reference in some function description.
Fixes:
b66bfdf238b9 ("arm: stm32mp: bsec: migrate trace to log macro")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Tue, 15 Feb 2022 15:08:50 +0000 (16:08 +0100)]
stm32mp: bsec: add permanent lock write support
Add support of the permanent lock support in U-Boot proper
when BSEC is not managed by secure monitor (TF-A SP_MIN or OP-TEE).
This patch avoid issue with stm32key command and fuse command
on basic boot for this missing feature of U-Boot BSEC driver.
Reported-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Christophe Kerello [Tue, 22 Feb 2022 16:38:49 +0000 (17:38 +0100)]
mtd: rawnand: stm32_fmc2: add NAND Write Protect support
This patch adds the support of the WP# signal. WP will be disabled
before the first access to the NAND flash.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tom Rini [Mon, 14 Mar 2022 20:39:08 +0000 (16:39 -0400)]
Prepare v2022.04-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 14 Mar 2022 18:04:55 +0000 (14:04 -0400)]
Merge branch '2022-03-14-regression-fixes'
- Regression fixes for RK3399 eMMC, j721e Sierra SerDes driver,
vexpress64 autoboot and tbs2910 image size
Soeren Moch [Mon, 14 Mar 2022 08:26:25 +0000 (09:26 +0100)]
board: tbs2910: Enable Link Time Optimizations in defconfig
This saves about 12 kBytes image size and helps to stay within the
size limit.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Andre Przywara [Fri, 4 Mar 2022 16:30:08 +0000 (16:30 +0000)]
vexpress64: fvp: Fix automatic boot
Commit
90f262a6951f ("vexpress64: Clean up BASE_FVP boot configuration")
cleaned up the usage of default address variables, but missed to update
the address for the kernel in the FVP's bootcmd definition.
Change ${kernel_addr} to read ${kernel_addr_r} to bring back the
automated boot for the fastmodel.
Also use "setenv" instead of the potentially ambiguous "set" on the way.
Fixes:
90f262a6951f ("vexpress64: Clean up BASE_FVP boot configuration")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Aswath Govindraju [Fri, 4 Mar 2022 12:15:26 +0000 (17:45 +0530)]
board: ti: j721e: evm.c: Fix the probing of in Sierra SerDes0
Initialization and power on operations of links have been moved under the
link device in the Sierra SerDes driver. Also, the UCLASS of
sierra_phy_provider has been changed to UCLASS_MISC.
Therefore, fix the probing of SerDes0 instance accordingly.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
Aswath Govindraju [Fri, 4 Mar 2022 12:15:25 +0000 (17:45 +0530)]
phy: cadence: Sierra: Move the link operations from serdes phy to link device
In commit
6f46c7441a9f ("phy: cadence: Sierra: Add a UCLASS_PHY device for
links"), a separate udevice of type UCLASS_PHY was created for each link.
Therefore, move the corresponding link operations under the link device.
Also, change the uclass of sierra phy to UCLASS_MISC as it is no longer the
phy device.
Fixes:
6f46c7441a9f ("phy: cadence: Sierra: Add a UCLASS_PHY device for links")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
Alper Nebi Yasak [Fri, 28 Jan 2022 22:42:37 +0000 (01:42 +0300)]
rockchip: sdhci: Fix RK3399 eMMC PHY power cycling
The Rockchip RK3399 eMMC PHY has to be power-cycled while changing its
clock speed to some higher speeds. This is dependent on the desired
SDHCI clock speed, and it looks like the PHY should be powered off while
setting the SDHCI clock in these cases.
Commit
ac804143cfd1 ("mmc: rockchip_sdhci: add phy and clock config for
rk3399") attempts to do this in the set_ios_post() hook by setting the
SDHCI clock once more while the PHY is turned off/on as necessary, as
the SDHCI framework does not provide a way to override how it sets its
clock. However, the commit breaks reinitializing the eMMC on a few
boards including chromebook_kevin and reportedly ROCKPro64.
This patch reworks the power cycling to utilize the SDHCI framework
slightly better (using the set_control_reg() hook to power off the PHY
and set_ios_post() hook to power it back on) which happens to fix the
issue, at least on a chromebook_kevin.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 14 Mar 2022 15:24:20 +0000 (11:24 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- kwboot: Misc minor improvement and fixes, e.g. mix of arguments (Pali)
- PCI: a37xx: Remap IO space to bus address 0x0 (Pali)
Tom Rini [Mon, 14 Mar 2022 14:57:15 +0000 (10:57 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-x86
- Trivial fixes for x86
Pali Rohár [Mon, 7 Mar 2022 18:12:59 +0000 (19:12 +0100)]
arm: a37xx: Remap IO space to bus address 0x0
Remap PCI I/O space to the bus address 0x0 in the Armada 37xx device-tree
in order to support legacy I/O port based cards which have hardcoded I/O
ports in low address space.
Some legacy PCI I/O based cards do not support 32-bit I/O addressing.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 7 Mar 2022 18:03:09 +0000 (19:03 +0100)]
tools: kwboot: Allow to mix positional arguments with option -b
Commit
9e6d71d2b55f ("tools: kwboot: Allow to use -b without image path as
the last getopt() option") broke usage of kwboot with following arguments:
kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot-spl.kwb
Fix parsing of option -b with optional argument again.
Fixes:
9e6d71d2b55f ("tools: kwboot: Allow to use -b without image path as the last getopt() option")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reported-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Tony Dinh <mibodhi at gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 7 Mar 2022 18:03:08 +0000 (19:03 +0100)]
tools: kwboot: Check if baudrate value is supported before sending image
Call kwboot_open_tty() which baudrate value which was specified at the
command line by option -B. This function returns error if baudrate is not
supported by selected tty device.
Initial baudrate for image transfer is always 115200, so call
kwboot_tty_change_baudrate() with value 115200 immediately after
kwboot_open_tty() if baudrate specified by option -B is different than
115200.
This makes kwboot fail immediately, informing that baudrate is unsupported,
instead of failing only after the first part of image is already sent.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 7 Mar 2022 18:03:07 +0000 (19:03 +0100)]
tools: kwboot: Allow to specify custom baudrate only in supported operations
Custom baudrate different than 115200 may be specified only when kwboot is
not going to send boot/debug message pattern or when it is going to send
boot message pattern with image file (in which case baudrate change happens
after sending kwbimage header). BootROM detects boot/debug message pattern
only at baudrate 115200.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Simon Glass [Sun, 13 Mar 2022 06:03:28 +0000 (23:03 -0700)]
x86: Correct the coreboot header file in MAINTAINERS
This board has its own config header file. Correct it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 13 Mar 2022 06:03:27 +0000 (23:03 -0700)]
x86: Add an enum name for the GNVS firmware type
This enum is currently anonymous. Add a name so it can be used in the
code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Sun, 13 Mar 2022 12:18:17 +0000 (08:18 -0400)]
Merge tag 'efi-2022-04-rc3-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc3-2
Documentation:
* Fix description for SiFive Unmatched
* Add libgnutls28-dev to build dependencies
UEFI
* Avoid possibly invalid GUID pointers for protocol interfaces
Other
* Serial console support for cls command
Tom Rini [Sat, 12 Mar 2022 12:20:29 +0000 (07:20 -0500)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-spi
- sunXi SPI fixups (Andre)
- bcm iproc qspi (Rayagonda)
Heinrich Schuchardt [Wed, 9 Mar 2022 18:56:23 +0000 (19:56 +0100)]
efi_loader: copy GUID in InstallProtocolInterface()
InstallProtocolInterface() is called with a pointer to the protocol GUID.
There is not guarantee that the memory used by the caller for the protocol
GUID stays allocated. To play it safe the GUID should be copied to U-Boot's
internal structures.
Reported-by: Joerie de Gram <j.de.gram@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sat, 12 Mar 2022 10:56:23 +0000 (11:56 +0100)]
doc: add libgnutls28-dev to build dependencies
mkeficapsule requires package libgnutls28-dev for building
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Thu, 10 Mar 2022 10:32:49 +0000 (11:32 +0100)]
doc: path to u-boot-spl.bin on SiFive Unmatched board
u-boot-spl.bin is built in spl/.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Fri, 11 Feb 2022 17:11:05 +0000 (18:11 +0100)]
cmd: add serial console support for the cls command
Currently the cls command does not support the serial console
The screen can be cleared in the video uclass, the colored frame buffer
console, and the serial console by sending the same escape sequence.
This reduces the cls command to a single printf() statement on most
boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Niklas Cassel [Thu, 3 Mar 2022 18:26:39 +0000 (18:26 +0000)]
mtd: spi-nor-ids: Enable quad read for Gigadevice gd25lq128
The Gigadevice gd25lq128 serial flash exists in different versions,
all which identify themselves using the same JEDEC id.
gd25lq128c:
https://www.gigadevice.com/datasheet/gd25lq128
gd25lq128d:
https://www.gigadevice.com/datasheet/gd25lq128d
However, all versions support quad read, so enable it.
Tested and verified on the Sipeed MAix BiT board.
Fixes:
30b9a28a3f2d ("mtd: spi-nor-ids: Add Gigadevice gd25lq128 ID")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:06 +0000 (12:46 +0000)]
sunxi: boards: Enable SPI flash support in U-Boot proper
Some sunxi boards ship with SPI flash, which allows booting through the
BootROM. We cover this functionality by a separate SPL "mini" driver.
Separately we have a proper DM_SPI driver for U-Boot proper, which
provides access to the SPI flash through the "sf" command. That allows
to update the firmware on the SPI flash, also to store the environment
there.
However only very few boards actually enable support for U-Boot proper,
even though that would work and the SPL part is configured.
Use the cleaned up configuration scheme to enable SPI flash on those
boards which mention a SPI flash in their .dts, or which use the SPL SPI
support.
Out of the box this would enable storing the environment on the SPI
flash, and allows people to read or write the flash from U-Boot, for
instance to update the SPI flash when booted via an SD card.
For this to actually work there must be a "spi0" alias in the DT, which
most boards are missing. But this should be addressed separately.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:05 +0000 (12:46 +0000)]
env: sunxi: enable ENV_IS_IN_SPI_FLASH
Now that sunxi uses CONFIG_SPI more sanely, and can also now properly
load the environment from SPI flash, let's enable the symbol that
actually considers the SPI flash when accessing the environment.
As this symbol depends on CONFIG_SPI, which we now only enable if the
board has a SPI flash, we can make if "default y" for all Allwinner
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:04 +0000 (12:46 +0000)]
sunxi: use boot source for determining environment location
Currently we only support to load the environment from raw MMC or FAT
locations on Allwinner boards. With the advent of SPI flash we probably
also want to support using the environment there, so we need to become
a bit more flexible.
Change the environment priority function to take the boot source into
account. When booted from eMMC or SD card, we use FAT or MMC, if
configured, as before.
If we are booted from SPI flash, we try to use the environment from
there, if possible. The same is true for NAND flash booting, although
this is somewhat theoretical right now (as untested).
This way we can use the same image for SD and SPI flash booting, which
allows us to simply copy a booted image from SD card to the SPI flash,
for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:03 +0000 (12:46 +0000)]
env: sunxi: Define location in SPI flash
To allow loading and storing the environment from SPI flash, adjust the
raw offset variables for Allwinner boards to make sense there.
U-Boot (including SPL and other blobs) is loaded from the beginning of
SPI flash, so move the environment location as far back as possible, to
not create unnecessary limits. As those offsets are shared with (now
mostly unused) raw MMC environment, we should respect the common one
megabyte limit, which also makes sense on SPI flash.
So limit the environment for those raw locations to 64KB, and place it
just below 1MB (@960KB).
Those values are currently unused, unless someone forcibly enables the
raw MMC environment. In this case it would break as of now, as the
current offset of 544KB is far too low for the current (arm64) U-Boot
proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:02 +0000 (12:46 +0000)]
sunxi: Kconfig: Fix up SPI configuration
Commit
7945caf22c44 ("arm: sunxi: Enable SPI/SPI-FLASH support for A64")
selected CONFIG_SPI by default on all Allwinner A64 boards, even though
only 4 out of the 14 A64 boards have a SPI flash chip. All other SoCs
had to manually select DM_SPI and friends, even though they are a
platform property (the sunxi SPI driver is DM_SPI only).
Clean this up to allow easy selection of SPI flash support in U-Boot
proper, by selecting DM_SPI and DM_SPI_FLASH *if* CONFIG_SPI is
selected, for *all* Allwinner SoCs. This simplifies the defconfig for
two Libretech boards already.
Also remove the forced CONFIG_SPI from the A64 Kconfig, instead let the
four boards which allow SPI booting select this explicitly.
Any board wishing to support SPI flash in U-Boot proper now just defines
CONFIG_SPI and CONFIG_SPI_FLASH_<vendor> in its defconfig, Kconfig takes
care of the rest.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Tue, 8 Mar 2022 13:42:51 +0000 (08:42 -0500)]
Merge branch '2022-03-08-assorted-fixes'
- serial uclass fix, mailmap/gitignore updates
Philippe Reynes [Tue, 8 Mar 2022 09:37:19 +0000 (10:37 +0100)]
board: .gitignore: replace dsdt.c by dsdt_generated.c
Since commit
5d94cbd1dca7 ("scripts: Makefile.lib: generate
dsdt_generated.c instead of dsdt.c"), the file generated
is named dsdt_generated.c instead of dsdt.c.
So all files .gitignore referencing dsdt.c should be
upated with dsdt_generated.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Mark Kettenis [Mon, 21 Feb 2022 21:17:37 +0000 (22:17 +0100)]
drivers: serial: Make sure we really return a serial device
The stdout-path property in the device tree does not necessarily
point at a serial device. On machines such as the Apple M1 laptops
where the serial port isn't easy to access and users expect to see
console output on the integrated display stdout-path may point at
the device tree node for the framebuffer for example.
If stdout-path does not point at a node for a serial device, the
serial_check_stdout() will not find a bound device and will drop
down into code that attempts to use lists_bind_fdt() to bind a
device anyway. However, that fallback code does not check that
the uclass of the device is UCLASS_SERIAL. So if stdout-path points
at the framebuffer instead of the serial device it will return a
UCLASS_VIDEO device. Since the code that calls this function
expects the returned device to be a UCLASS_SERIAL device, U-Boot
will crash as soon as it attempts to send output to the console.
Add a check here to verify that the uclass of the bound device
really is UCLASS_SERIAL. If it isn't, serial_check_stdout() will
return an error and serial_find_console_or_panic() will use the
serial device with sequence number 0 as the console and all is fine.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 7 Mar 2022 07:41:21 +0000 (08:41 +0100)]
.mailmap: Fix Heinrich's xypron.glpk@gmx.de record
There is one issue with Heinrich xypron.glpk@gmx.de <xypron.glpk@gmx.de>
record which should be specifically grouped with his name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Tue, 8 Mar 2022 13:42:20 +0000 (08:42 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-watchdog
- Update MAINTAINERS file (Stefan)
- wdt-uclass.c: add a property u-boot, noautostart (Philippe)
- armada_37xx: Probe driver also when watchdog is already running (Pali)
- rti_wdt: Add 10% safety margin to clock frequency (Jan)
Jan Kiszka [Tue, 8 Mar 2022 06:25:50 +0000 (07:25 +0100)]
watchdog: rti_wdt: Add 10% safety margin to clock frequency
When running against RC_OSC_32k, the watchdog may suffer from running
faster than expected, expiring earlier. The Linux kernel adds a 10%
margin to the timeout calculation by slowing down the read clock rate
accordingly. Do the same here, also to have comparable preset values
for both drivers.
Along this, fix the name of the local var holding to frequency - in Hz,
not kHz.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 23 Feb 2022 13:21:40 +0000 (14:21 +0100)]
watchdog: armada_37xx: Probe driver also when watchdog is already running
If Armada 37xx watchdog is started before U-Boot then CNTR_CTRL_ACTIVE bit
is set, U-Boot armada-37xx-wdt.c driver fails to initialize and so U-Boot
is unable to use or kick this watchdog.
Do not check for CNTR_CTRL_ACTIVE bit and always initialize watchdog. Same
behavior is implemented in Linux kernel driver.
This change allows to activate watchdog in firmware which loads U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Philippe Reynes [Thu, 10 Feb 2022 17:17:54 +0000 (18:17 +0100)]
drivers: watchdog: wdt-uclass.c: add a property u-boot, noautostart
Since commit
492ee6b8d0e7 ("watchdog: wdt-uclass.c: handle all DM
watchdogs in watchdog_reset()"), all the watchdog are started when
the config WATCHDOG_AUTOSTART.
To avoid a binary choice none/all, a property u-boot,noautostart
may be added in the watchdog node of the u-boot device tree to not
autostart this watchdog.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 13 Jan 2022 15:57:31 +0000 (16:57 +0100)]
MAINTAINERS: Add watchdog maintainers entry
I've been handling "inofficially" the watchdog related patches for a few
years now. Let's make this official and add a tree for it and also add
myself here in the MAINTAINERS file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Harald Seiler <hws@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sun, 6 Mar 2022 01:46:55 +0000 (20:46 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi
- Fix ARMv5/F1C100 FEL booting
- Fix F1C100 reset
- Introduce proper F1C100 boot method detection
- Enable SPI booting for F1C100
Boot tested from FEL, SPI, SD card and eMMC (where applicable) on
Pine64-LTS, Pine-H64, BananaPi M1, OrangePi Zero, LicheePi Nano(F1C100).
Tom Rini [Sat, 5 Mar 2022 16:34:31 +0000 (11:34 -0500)]
Merge branch '2022-03-04-assorted-minor-fixes'
- mailmap file updates, OpenSSL code cleanup, assorted TI platform
fixes, typo fix.
Yann Droneaud [Tue, 1 Mar 2022 15:12:34 +0000 (16:12 +0100)]
lib: rsa: use actual OpenSSL 1.1.0 EVP MD API
Since OpenSSL 1.1.0, EVP_MD_CTX_create() is EVP_MD_CTX_new()
EVP_MD_CTX_destroy() is EVP_MD_CTX_free()
EVP_MD_CTX_init() is EVP_MD_CTX_reset()
As there's no need to reset a newly created EVP_MD_CTX, moreover
EVP_DigestSignInit() does the reset, thus call to EVP_MD_CTX_init()
can be dropped.
As there's no need to reset an EVP_MD_CTX before it's destroyed,
as it will be reset by EVP_MD_CTX_free(), call to EVP_MD_CTX_reset()
is not needed and can be dropped.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Michal Simek [Tue, 1 Mar 2022 11:43:32 +0000 (12:43 +0100)]
.mailmap: Record all address for main U-Boot contributor
Based on looking at top contributors it was seen that top statistics from
top contributors don't include all contributions from different email
addresses. That's why I checked all top contributors are checked it.
git shortlog -n $START..$END -e -s
The patch is adding mapping for Bin Meng, Marek Vasut, Masahiro Yamada,
Michal Simek, Tom Rini, Wolfgang Denk.
And also use mapping for Stefan Roese and Wolfgang Denk to be properly
counted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Heinrich Schuchardt [Tue, 1 Mar 2022 07:53:56 +0000 (08:53 +0100)]
mkimage: error handling for FIT image
If parameter -F is given but FIT support is missing, a NULL pointer might
dereferenced (Coverity CID 350249).
If incorrect parameters are given, provide a message and show usage.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Sébastien Szymanski [Fri, 25 Feb 2022 13:48:54 +0000 (14:48 +0100)]
cmd: pwm: fix typo 'eisable' -> 'disable'
Fixed misspelled 'disable' in help text.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Jan Kiszka [Wed, 16 Feb 2022 08:06:49 +0000 (09:06 +0100)]
arm: dts: iot2050: Add cfg register space for ringacc and udmap
Recent unrelated fixes (
9876ae7db6da) revealed that we were missing bits
from
2af181b53e28 in the IOT2050 dt. Add them, but only for main U-Boot.
SPL loads from QSPI only, thus cannot use DMA.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Aswath Govindraju [Wed, 16 Feb 2022 05:57:24 +0000 (11:27 +0530)]
configs: j721e_*_evm_a72_defconfig: Enable config for setting mmc speed mode
Enable config for setting mmc speed mode from U-Boot command line.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Christian Gmeiner [Tue, 15 Feb 2022 06:47:55 +0000 (07:47 +0100)]
arm: mach-k3: am6_init: Use CONFIG_TI_I2C_BOARD_DETECT
We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT
is set. Same as done for am64.
This makes it possible to add a custom am65 based board design to
U-Boot that does not use this board detection mechanism.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Romain Naour [Thu, 10 Feb 2022 22:13:36 +0000 (23:13 +0100)]
configs: ti: use standard configuration nodes naming
Currently, any u-boot bootloader for ti armv7 platforms using
DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1)
doesn't boot when built with Yocto Poky (openembedded-core).
## Loading kernel from FIT Image at
90000000 ...
Could not find configuration node
ERROR: can't get kernel image!
Arago forked the kernel-fitimage class [1] and altered the
configuration nodes naming while adding the OPTEE support by
using FITIMAGE_CONF_BY_NAME by default [2].
The "upstream" kernel-fitimage class from openembedded-core still
add the "conf-" prefix for each configuration nodes [3].
The ITS file format (from doc/uImage.FIT/source_file_format.txt)
is not really accurate with the expected naming of these nodes.
But in practice the "conf-" prefix is widely used.
When the FIT image support has been added for ti armv7 platforms
the naming from Arago has been used [3]. Fix this issue by adding
the prefix expected by the ITS file generated by kernel-fitimage
class from openembedded-core.
[1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=
719ab1b2098bcdc59c249e3529fa82cb1b9130e6
[2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=
f23f2876a0cda89241d031bb7ba0b4256ed90035
[3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fitimage.bbclass?h=yocto-3.1.13#n290
[3]
1e93cc8473e4fe018aececc8ed3bf8fc2b3ff561
Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Denys Dmytriyenko <denys@konsulko.com>
Tom Rini [Fri, 4 Mar 2022 13:27:32 +0000 (08:27 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- pci_mvebu: Minor cleanup (Pali)
- mvebu: turris_omnia: Enable ext4 write support (Marek)
- a37xx: Misc fixes in PCI and pinctrl (Pali & Marek)
- a38x/rtc: Fix null pointer access (Francios)
- mvebu: x530: clearfog: Fix ODT configuration (Chris)
- kwboot: Fix boot and terminal mode (Pali)
Pali Rohár [Wed, 2 Mar 2022 10:49:27 +0000 (11:49 +0100)]
tools: kwboot: Update references with public links
Public documents about BootROM of some Marvell SoCs are available in the
public Web Archive. Put this information into source code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:26 +0000 (11:49 +0100)]
tools: kwboot: Update doc about Avanta
Testes proved that current kwboot version supports also Avanta SoCs.
It looks like that Avanta SoCs are using same kwbimage format as Armada.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:25 +0000 (11:49 +0100)]
tools: kwboot: Update manpage
Document -D, -b, -d, -q and -s options.
Add common examples how to use kwboot.
Add information about Armada 38x BootROM bug for debug console mode and how
to workaround it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:24 +0000 (11:49 +0100)]
tools: kwboot: Update usage
Add all supported Armada SoCs and document -b and -d options in usage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:23 +0000 (11:49 +0100)]
tools: kwboot: Add support for backspace key in mini terminal
Marvell BootROM recognize only '\b' byte as backspace. Use terminfo
for retrieving current backspace sequence and replace any occurrence of
backspace sequence by the '\b' byte.
Reading terminfo database is possible via tigetstr() function from system
library libtinfo.so.*. So link kwboot with -ltinfo.
Normally terminfo functions are in <term.h> system header file. But this
header file conflicts with U-Boot "termios_linux.h" header file. So declare
terminfo functions manually.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:22 +0000 (11:49 +0100)]
tools: kwboot: Fix sending and processing debug message pattern (-d option)
-d option is currently broken. In most cases BootROM does not detect this
message pattern. For sending debug message pattern it is needed to do same
steps as for boot message pattern.
Implement sending debug message pattern via same separate thread like it is
for boot message pattern.
Checking if BootROM entered into UART debug mode is different than
detecting UART boot mode. When in boot mode, BootROM sends xmodem NAK
bytes. When in debug mode, BootROM activates console echo and reply back
every written byte (extept \r\n which is interpreted as executing command
and \b which is interpreting as removing the last sent byte).
So in kwboot, check that BootROM send back at least 4 debug message
patterns as a echo reply for debug message patterns which kwboot is sending
in the loop.
Then there is another observation, if host writes too many bytes (as
command) then BootROM command line buffer may overflow after trying to
execute such long command. To workaround this overflow, it is enough to
remove bytes from the input line buffer by sending 3 \b bytes for every
sent character. So do it.
With this change, it is possbile to enter into the UART debug mode with
kwboot -d option.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:21 +0000 (11:49 +0100)]
tools: kwboot: Use separate thread for sending boot message pattern
After BootROM successfully detects boot message pattern on UART it waits
until host stop sending data on UART. For example Armada 385 BootROM
requires that host does not send anything on UART at least 24 ms. If host
is still sending something then BootROM waits (possibly infinitely).
BootROM successfully detects boot message pattern if it receives it in
small period of time after power on.
So to ensure that host put BootROM into UART boot mode, host must send
continuous stream of boot message pattern with a small gap (for A385 at
least 24 ms) after series of pattern. But this gap cannot be too often or
too long to ensure that it does not cover whole BootROM time window when it
is detecting for boot message pattern.
Therefore it is needed to do following steps in cycle without any delay:
1. send series of boot message pattern over UART
2. wait until kernel transmit all data
3. sleep small period of time
At the same time, host needs to monitor input queue, data received on the
UART and checking if it contains NAK byte by which BootROM informs that
xmodem transfer is ready.
But it is not possible to wait until kernel transmit all data on UART and
at the same time in the one process to also wait for input data. This is
limitation of POSIX tty API and also by linux kernel that it does not
provide asynchronous function for waiting until all data are transmitted.
There is only synchronous variant tcdrain().
So to correctly implement this handshake on systems with linux kernel, it
is needed to use tcdrain() in separate thread.
Implement sending of boot message pattern in one thread and reading of
reply in the main thread. Use pthread library for threads.
This change makes UART booting on Armada 385 more reliable. It is possible
to start kwboot and power on board after minute and kwboot correctly put
board into UART boot mode.
Old implementation without separate thread has an issue that it read just
one byte from UART input queue and then it send 128 message pattern to the
output queue. If some noise was on UART then kwboot was not able to read
BootROM response as its input queue was just overflowed and kwboot was
sending more data than receiving.
This change basically fixed above issue too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:20 +0000 (11:49 +0100)]
tools: kwboot: Cleanup bootmsg and debugmsg variables
Function kwboot_debugmsg() is always called with kwboot_msg_debug as msg
and function kwboot_bootmsg() with kwboot_msg_debug as msg. Function
kwboot_bootmsg() is never called with NULL msg.
Simplify, cleanup and remove dead code.
No functional change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:19 +0000 (11:49 +0100)]
tools: kwboot: Remove msg_req_delay
Variable msg_req_delay is set but never used. So completely remove it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 2 Mar 2022 10:49:18 +0000 (11:49 +0100)]
tools: kwboot: Check for return value of kwboot_tty_send() and tcflush()
Failure of kwboot_tty_send() and tcflush() functions is fatal, it does not
make sense to continue. So return error back to the caller like in other
places where are called these functions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Chris Packham [Tue, 1 Mar 2022 00:53:23 +0000 (13:53 +1300)]
ARM: mvebu: x530: clearfog: Add ODT configuration
Commit
369e532691e0 ("ddr: marvell: a38x: allow board specific ODT
configuration") added the odt_config member to struct
mv_ddr_topology_map ahead of the clk_enable and ck_delay members. This
means that any boards that configured either of clk_enable or ck_delay
needed to have their board topology updated. This affects the x530 and
clearfog boards. Other A38x boards don't touch any of the trailing
members of mv_ddr_topology_map so don't need updating.
Fixes:
369e532691e0 ("ddr: marvell: a38x: allow board specific ODT configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Mon, 28 Feb 2022 14:59:37 +0000 (15:59 +0100)]
arm64: a37xx: pinctrl: Fix PWM pins indexes
Commit
5534fb4f4833 ("arm64: a37xx: pinctrl: Correct PWM pins
definitions") introduced bogus definitions os PWM pins: all 4 pins have
index 11, instead of having indexes 11, 12, 13, 14.
Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Francois Berder [Mon, 28 Feb 2022 09:31:45 +0000 (10:31 +0100)]
drivers: rtc: fix null pointer access in armada38x_rtc_reset
Replace null pointer by pointer to device registers when calling
armada38x_rtc_write.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Wed, 23 Feb 2022 12:52:32 +0000 (13:52 +0100)]
arm: a37xx: pci: Fix a3700_fdt_fix_pcie_regions() function again
The a3700_fdt_fix_pcie_regions() function still computes nonsense.
It computes the fixup offset from the PCI address taken from the first
row of the "ranges" array, which means that:
- PCI address must equal CPU address (otherwise the computed fix offset
will be wrong),
- the first row must contain the lowest address.
This is the case for the default device-tree, which is why we didn't
notice it.
It also adds the fixup offset to all PCI and CPU addresses, which is
wrong.
Instead:
1) The fixup offset must be computed from the CPU address, not PCI
address.
2) The fixup offset must be computed from the row containing the lowest
CPU address, which is not necessarily contained in the first row.
3) The PCI address - the address to which the PCIe controller remaps the
address space as seen from the point of view of the PCIe device -
must be fixed by the fix offset in the same way as the CPU address
only in the special case when the CPU adn PCI addresses are the same.
Same addresses means that remapping is disabled, and thus if we
change the CPU address, we need also to change the PCI address so
that the remapping is still disabled afterwards.
Consider an example:
The ranges entries contain:
PCI address CPU address
70000000 EA000000
E9000000 E9000000
EB000000 EB000000
By default CPU PCIe window is at:
E8000000 -
F0000000
Consider the case when TF-A moves it to:
F2000000 -
FA000000
Until now the function would take the PCI address of the first entry:
70000000, and the new base,
F2000000, to compute the fix offset:
F2000000 -
70000000 =
82000000, and then add 8200000 to all addresses,
resulting in
PCI address CPU address
F2000000 6C000000
6B000000 6B000000
6D000000 6D000000
which is complete nonsense - none of the CPU addresses is in the
requested window.
Now it will take the lowest CPU address, which is in second row,
E9000000, and compute the fix offset
F2000000 -
E9000000 =
09000000,
and then add it to all CPU addresses and those PCI addresses which
equal to their corresponding CPU addresses, resulting in
PCI address CPU address
70000000 F3000000
F2000000 F2000000
F4000000 F4000000
where all of the CPU addresses are in the needed window.
Fixes:
4a82fca8e330 ("arm: a37xx: pci: Fix a3700_fdt_fix_pcie_regions() function")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Fri, 18 Feb 2022 16:46:25 +0000 (17:46 +0100)]
arm: mvebu: turris_omnia: Enable ext4 write support in defconfig
Enable ext4 write support in Turris Omnia's defconfig. Some users find
it useful.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 18 Feb 2022 11:25:23 +0000 (12:25 +0100)]
pci: pci_mvebu: Cleanup macro names
Use "MVPCIE_" prefix instead of generic "PCIE_" prefix for pci_mvebu.c
specific macros. Define offset macros for Root Port registers and use
standard register macros from pci.h when accessing Root Port registers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 18 Feb 2022 11:25:22 +0000 (12:25 +0100)]
pci: pci_mvebu: Remove unused SELECT and lane_mask
Macro SELECT() is unused and struct mvebu_pcie field lane_mask is unused
too. Remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 18 Feb 2022 11:24:13 +0000 (12:24 +0100)]
tools: kwboot: Fix quitting terminal
Sometimes kwboot after quitting terminal prints error message:
terminal: Bad address
This is caused by trying to call write() syscall with count of (size_t)-1
bytes.
When quit sequence is split into more read() calls then number of input
bytes (nin) at the end of cycle can underflow and be negative. Fix it.
Fixes:
de7514046ea5 ("tools: kwboot: Fix detection of quit esc sequence")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Thu, 3 Mar 2022 13:24:37 +0000 (08:24 -0500)]
Merge tag 'u-boot-at91-fixes-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-atmel fixes for the 2022.04 cycle:
This fixes set includes only a single fix for the Ethernet on sama7g5ek
board which is broken at the moment.
Tom Rini [Thu, 3 Mar 2022 13:24:13 +0000 (08:24 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
Update and fixes for sl28, lx2, pblimage generation for some powerpc
products
Andre Przywara [Wed, 2 Mar 2022 01:30:55 +0000 (01:30 +0000)]
sunxi: f1c100s: Drop SYSRESET to enable reset functionality
The F1C100s DT contains the wrong compatible string for the watchdog,
which breaks reset functionality.
Updating the DT goes via the Linux tree, but to allow reset
functionality meanwhile (useful for development!), disable SYSRESET for
now, to let the old-fashioned watchdog driver kick in and provide the
reset_cpu() implementation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Tue, 1 Mar 2022 12:21:58 +0000 (12:21 +0000)]
sunxi: f1c100s: Fix FEL registers restore
Commit
88998f777531 ("arm: arm926ej-s: Add sunxi code") introduced
the ARM926 version of the code to save and restore some FEL state, to
be able to return to the BROM FEL code after the SPL has run.
However during review a change was made, that happened to mess up the
register restore part, so SCTLR and CPSR ended up with the wrong values,
breaking return to FEL.
Use the same offset that we actually save those registers to, to make
FEL booting actually work on the Lichee Pi Nano.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jesse Taube [Sat, 12 Feb 2022 00:32:35 +0000 (19:32 -0500)]
mach-sunxi: Enable SPI boot for SUNIV and licheepi nano
Enable SPI boot in SPL on SUNIV architecture and use
it in the licheepi nano that uses the F1C100s.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jesse Taube [Sat, 12 Feb 2022 00:32:34 +0000 (19:32 -0500)]
mach-sunxi: Add SPL SPI boot for SUNIV
The SUNIV SoCs come with a sun6i-style SPI controller at the base address
of sun4i SPI controller. The module clock of the SPI controller is
missing which leaves us running directly from the AHB clock, which is
set to 200MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Icenowy: Original implementation]
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
[Jesse: adaptation to Upstream U-Boot]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jesse Taube [Sat, 12 Feb 2022 00:32:33 +0000 (19:32 -0500)]
mach-sunxi: Add boot device detection for SUNIV/F1C100s
In contrast to other Allwinner SoCs the F1C100s BROM does not store a
boot source indicator in the eGON header in SRAM. This leaves the SPL
guessing where we were exactly booted from, and for instance trying
the SD card first, even though we booted from SPI flash.
By inspecting the BROM code and by experimentation, Samuel found that the
top of the BROM stack contains unique pointers for each of the boot
sources, which we can use as a boot source indicator.
This patch removes the existing board_boot_order bodge and replace it
with a proper boot source indication function.
The only caveat is that this only works in the SPL, as the SPL header
gets overwritten with the exception vectors, once U-Boot proper takes
over. Always return MMC0 as the boot source, when called from U-Boot
proper, as a placeholder for now, until we find another way.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Suggested-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tom Rini [Tue, 1 Mar 2022 12:48:39 +0000 (07:48 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
Tim Harvey [Mon, 28 Feb 2022 22:53:21 +0000 (14:53 -0800)]
phy: nop-phy: Fix phy reset if no reset-gpio defined
Ensure there is a valid reset-gpio defined before using it.
Fixes:
f9852acdce02 ("phy: nop-phy: Fix enabling reset")
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tom Rini [Mon, 28 Feb 2022 23:02:33 +0000 (18:02 -0500)]
Prepare v2022.04-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 28 Feb 2022 20:45:52 +0000 (15:45 -0500)]
Merge branch '2022-02-28-bugfixes'
- Assorted bugfixes
Linus Walleij [Sun, 20 Feb 2022 22:47:01 +0000 (23:47 +0100)]
board: stemmy: Detect board variants and patch DTB
This patch scans the cmdline from the Samsung SBL (second stage
bootloader) and stores the parameters board_id=N and lcdtype=N
in order to augment the DTB for different board and LCD types.
We then add a custom ft_board_setup() callback that will inspect
the DTB and patch it using the stored LCD type. At this point
we know which product we are dealing with, so using the passed
board_id we can also print the board variant for diagnostics.
We patch the Codina, Skomer and Kyle DTBs to use the right
LCD type as passed in lcdtype from the SBL.
This also creates an infrastructure for handling any other
Samsung U8500 board variants that may need a slightly augmented
DTB.
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Janne Grunau [Sat, 19 Feb 2022 13:05:19 +0000 (14:05 +0100)]
arm: apple: Switch to fully dynamic mem layout
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Felix Brack [Mon, 21 Feb 2022 13:26:05 +0000 (14:26 +0100)]
arm: pdu001: Setup pinmux for console UART as early as possible
To make sure we get a working console as soon as possible in the SPL the
UART pins require to be configured earlier. This is especially
true for the pins of UART3, since the PDU001 board uses this UART for
the console by default.
Signed-off-by: Felix Brack <fb@ltec.ch>
Felix Brack [Tue, 15 Feb 2022 14:27:23 +0000 (15:27 +0100)]
arm: pdu001: Fix early debugging UART
The changes from commit
0dba45864b2a ("arm: Init the debug UART")
prevent the early debug UART from being initialized correctly.
To fix this we not just configure the pin multiplexer but add setting up
early clocks.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Sun, 13 Feb 2022 00:09:46 +0000 (01:09 +0100)]
tools: mkimage/dumpimage: Allow to use -l with -T
Currently -l option for mkimage and dumpimage ignores option -T and always
tries to autodetect image type.
With this change it is possible to tell mkimage and dumpimage to parse
image file as specific type (and not random autodetected type). This allows
to use mkimage -l or dumpimage -l as tool for validating image.
params.type for -l option is now by default initialized to zero
(IH_TYPE_INVALID) instead of IH_TYPE_KERNEL. imagetool_get_type() for
IH_TYPE_INVALID returns NULL, which is assigned to tparams. mkimage and
dumpimage code is extended to handle tparams with NULL for -l option. And
imagetool_verify_print_header() is extended to do validation via tparams if
is not NULL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Hou Zhiqiang [Thu, 17 Feb 2022 03:51:36 +0000 (11:51 +0800)]
tools: pblimage: fix image header verification function
The Layerscape platforms have different RCW header value from FSL
PowerPC platforms, the current image header verification callback
is only working on PowerPC, it will fail on Layerscape, this patch
is to fix this issue.
This is a historical problem and exposed by the following patch:
http://patchwork.ozlabs.org/project/uboot/patch/
20220114173443.9877-1-pali@kernel.org
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Daniel Klauer [Wed, 9 Feb 2022 14:53:41 +0000 (15:53 +0100)]
lx2160a: Fix distroboot device list for configs without USB/SCSI/etc
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Fri, 25 Feb 2022 12:51:56 +0000 (18:21 +0530)]
board: sl28: use fit image generator
Simplify the binman config and fdt nodes by using the "@..-SEQ"
substitutions and CONFIG_OF_LIST.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Fri, 25 Feb 2022 12:48:40 +0000 (18:18 +0530)]
board: sl28: disable random MAC address generation
Nowadays, u-boot (when CONFIG_NET_RANDOM_ETHADDR is set) will set
enetaddr to a random value if not set and then pass the randomly
generated MAC address to linux.
This is bad for the following reasons:
(1) it makes it impossible for linux to detect this error
(2) linux won't trigger any fallback mechanism for the case where
it didn't find any valid MAC address
(3) a saveenv will store this randomly generated MAC address in the
environment
Probably, the user will also be unaware that something is wrong. He will
just get different MAC addresses on each reboot, asking himself why this
is the case.
As this board usually have a serial port, the user can just fix this by
setting the MAC address manually in the environment. Also disable the
netconsole just in case, because it cannot be guaranteed that it will
work in any case. After all, this was just a convenience option, because
the bootloader - right now - doesn't have the ability to read the MAC
address, which is stored in the OTP. But it is far more important to
have a clear view of whats wrong with a board and that means we can no
longer use this Kconfig option.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 15 Nov 2021 22:45:50 +0000 (23:45 +0100)]
board: sl28: remove "Useful I2C tricks" section from docs
They are no longer needed, because we now have proper driver support for
the sl28cpld management controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 15 Nov 2021 22:45:49 +0000 (23:45 +0100)]
board: sl28: disable recovery watchdog
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 15 Nov 2021 22:45:48 +0000 (23:45 +0100)]
board: sl28: enable SoC watchdog support
The SoC provides two additional watchdogs integrated in the SoC. Enable
support for these.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 15 Nov 2021 22:45:47 +0000 (23:45 +0100)]
board: sl28: enable sl28cpld support
Enable the GPIO and watchdog driver. Don't start the watchdog
automatically, though.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 15 Nov 2021 22:45:46 +0000 (23:45 +0100)]
board: sl28: print CPLD version on bootup
Most of the time it is very useful to have the version of the board
management controller. Now that we have a driver, print it during
startup.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>