Alexandre Belloni [Tue, 20 Mar 2018 13:07:56 +0000 (14:07 +0100)]
dt-bindings: Add vendor prefix for Microsemi Corporation
Microsemi Corporation provides semiconductor and system solutions for
aerospace & defense, communications, data center and industrial markets.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Allan Nielsen <Allan.Nielsen@microsemi.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18853/
Signed-off-by: James Hogan <jhogan@kernel.org>
Mathias Kresin [Thu, 11 May 2017 06:18:24 +0000 (08:18 +0200)]
MIPS: ath79: Fix AR724X_PLL_REG_PCIE_CONFIG offset
According to the QCA u-boot source the "PCIE Phase Lock Loop
Configuration (PCIE_PLL_CONFIG)" register is for all SoCs except the
QCA955X and QCA956X at offset 0x10.
Since the PCIE PLL config register is only defined for the AR724x fix
only this value. The value is wrong since the day it was added and isn't
used by any driver yet.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16048/
Signed-off-by: James Hogan <jhogan@kernel.org>
Daniel Golle [Sat, 3 Jun 2017 18:20:14 +0000 (20:20 +0200)]
MIPS: pci-mt7620: Enable PCIe on MT7688
Use PCIe support for MT7628AN also on MT7688.
Tested on WRTNODE2R.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-mediatek@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/16223/
Signed-off-by: James Hogan <jhogan@kernel.org>
Matt Redfearn [Tue, 20 Feb 2018 09:58:16 +0000 (09:58 +0000)]
MIPS: pm-cps: Block system suspend when a JTAG probe is present
If a JTAG probe is connected to a MIPS cluster, then the CPC detects it
and latches the CPC.STAT_CONF.EJTAG_PROBE bit to 1. While set,
attempting to send a power-down command to a core will be blocked, and
the CPC will instead send the core to clock-off state. This can
interfere with systems fully entering a low power state where all cores,
CM, GIC, etc are powered down.
Detect that a JTAG probe is / has been connected to the cluster and
block the suspend attempt.
Attempting to suspend the system while a JTAG probe is connected now
yields:
# echo mem > /sys/power/state
[ 11.654000] PM: Syncing filesystems ... done.
[ 11.658000] JTAG probe is connected - abort suspend
-sh: echo: write error: Operation not permitted
#
To restore suspend, the JTAG probe should be disconnected or put into
quiescent state. Platform code can then clear the
CPC.STAT_CONF.EJTAG_PROBE bit.
Reported-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18641/
Signed-off-by: James Hogan <jhogan@kernel.org>
Matt Redfearn [Mon, 26 Feb 2018 17:02:45 +0000 (17:02 +0000)]
MIPS: VDSO: Replace __mips_isa_rev with MIPS_ISA_REV
Remove the need to check that __mips_isa_rev is defined by using the
newly added MIPS_ISA_REV.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18678/
Signed-off-by: James Hogan <jhogan@kernel.org>
Matt Redfearn [Mon, 26 Feb 2018 17:02:44 +0000 (17:02 +0000)]
MIPS: BPF: Replace __mips_isa_rev with MIPS_ISA_REV
Remove the need to check that __mips_isa_rev is defined by using the
newly added MIPS_ISA_REV.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18677/
Signed-off-by: James Hogan <jhogan@kernel.org>
Matt Redfearn [Mon, 26 Feb 2018 17:02:43 +0000 (17:02 +0000)]
MIPS: cpu-features.h: Replace __mips_isa_rev with MIPS_ISA_REV
Remove the need to check that __mips_isa_rev is defined by using the
newly added MIPS_ISA_REV.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: "Maciej W. Rozycki" <macro@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18675/
Signed-off-by: James Hogan <jhogan@kernel.org>
Matt Redfearn [Mon, 26 Feb 2018 17:02:42 +0000 (17:02 +0000)]
MIPS: Introduce isa-rev.h to define MIPS_ISA_REV
There are multiple instances in the kernel where we need to include or
exclude particular instructions based on the ISA revision of the target
processor. For MIPS32 / MIPS64, the compiler exports a __mips_isa_rev
define. However, when targeting MIPS I - V, this define is absent. This
leads to each use of __mips_isa_rev having to check that it is defined
first. To simplify this, introduce the isa-rev.h header which always
exports MIPS_ISA_REV. The name is changed so as to avoid confusion with
the compiler builtin and to avoid accidentally using the builtin.
MIPS_ISA_REV is defined to the compilers builtin if provided, or 0,
which satisfies all current usages.
Suggested-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18676/
Signed-off-by: James Hogan <jhogan@kernel.org>
Paul Burton [Wed, 23 Aug 2017 20:53:16 +0000 (13:53 -0700)]
MIPS: Hang more efficiently on halt/powerdown/restart
The generic MIPS implementations of halting, powering down or restarting
the system all hang using a busy loop as a last resort. We have many
platforms which avoid this loop by implementing their own, many using
some variation upon executing a wait instruction to lower CPU power
usage if we reach this point.
In order to prepare for cleaning up these various custom implementations
of the same thing, this patch makes the generic machine_halt(),
machine_power_off() & machine_restart() functions each make use of the
wait instruction to lower CPU power usage in cases where we know that
the wait instruction is available. If wait isn't known to be supported
then we fall back to calling cpu_wait(), and if we don't have a
cpu_wait() callback then we effectively continue using a busy loop.
In effect the new machine_hang() function provides a superset of the
functionality that the various platforms currently provide differing
subsets of.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17178/
Signed-off-by: James Hogan <jhogan@kernel.org>
Andy Shevchenko [Thu, 21 Dec 2017 14:40:55 +0000 (16:40 +0200)]
FIRMWARE: bcm47xx_nvram: Replace mac address parsing
Replace sscanf() with mac_pton().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17982/
Signed-off-by: James Hogan <jhogan@kernel.org>
Jaedon Shin [Fri, 17 Nov 2017 02:19:44 +0000 (11:19 +0900)]
MIPS: BMIPS: Add Broadcom STB watchdog nodes
Adds watchdog device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17729/
Signed-off-by: James Hogan <jhogan@kernel.org>
Jaedon Shin [Fri, 17 Nov 2017 02:19:43 +0000 (11:19 +0900)]
MIPS: BMIPS: Add Broadcom STB wake-up timer nodes
Adds wake-up timer device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17728/
Signed-off-by: James Hogan <jhogan@kernel.org>
Jaedon Shin [Fri, 17 Nov 2017 02:19:42 +0000 (11:19 +0900)]
MIPS: BMIPS: Add Broadcom STB power management nodes
Adds power management nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17727/
Signed-off-by: James Hogan <jhogan@kernel.org>
James Hogan [Fri, 9 Feb 2018 16:11:58 +0000 (16:11 +0000)]
MIPS: Expand help text to list generic defconfigs
Expand the MIPS Makefile help text to list generic board names, generic
defconfigs, and legacy defconfigs which have been converted to generic
and are still usable.
Here's a snippet of the new "make ARCH=mips help" output:
...
If you are targeting a system supported by generic kernels you may
configure the kernel for a given architecture target like so:
{micro32,32,64}{r1,r2,r6}{el,}_defconfig <BOARDS="list of boards">
Where BOARDS is some subset of the following:
boston
ni169445
ranchu
sead-3
xilfpga
Specifically the following generic default configurations are
supported:
32r1_defconfig - Build generic kernel for MIPS32 r1
32r1el_defconfig - Build generic kernel for MIPS32 r1 little endian
32r2_defconfig - Build generic kernel for MIPS32 r2
32r2el_defconfig - Build generic kernel for MIPS32 r2 little endian
32r6_defconfig - Build generic kernel for MIPS32 r6
32r6el_defconfig - Build generic kernel for MIPS32 r6 little endian
64r1_defconfig - Build generic kernel for MIPS64 r1
64r1el_defconfig - Build generic kernel for MIPS64 r1 little endian
64r2_defconfig - Build generic kernel for MIPS64 r2
64r2el_defconfig - Build generic kernel for MIPS64 r2 little endian
64r6_defconfig - Build generic kernel for MIPS64 r6
64r6el_defconfig - Build generic kernel for MIPS64 r6 little endian
micro32r2_defconfig - Build generic kernel for microMIPS32 r2
micro32r2el_defconfig - Build generic kernel for microMIPS32 r2 little endian
The following legacy default configurations have been converted to
generic and can still be used:
sead3_defconfig - Build 32r2el_defconfig BOARDS=sead-3
sead3micro_defconfig - Build micro32r2el_defconfig BOARDS=sead-3
xilfpga_defconfig - Build 32r2el_defconfig BOARDS=xilfpga
...
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18598/
James Hogan [Fri, 9 Feb 2018 16:11:56 +0000 (16:11 +0000)]
MIPS: Refactor legacy defconfigs
Define legacy defconfigs which have been converted to the generic
platform more programatically, so that they can be listed in the
Makefile help text and as a separate Makefile target without
duplication.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18596/
James Hogan [Fri, 9 Feb 2018 22:11:07 +0000 (22:11 +0000)]
MIPS: generic: Enable crc32-mips on r6 configs
Enable the crc32-mips module on MIPS generic r6 configs, where the
required MIPS r6 CRC instructions may be available.
As well as allowing the CRC instructions to be utilised, this should
also ensure the module gets some build coverage.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Marcin Nowakowski <marcin.nowakowski@mips.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18602/
Marcin Nowakowski [Fri, 9 Feb 2018 22:11:06 +0000 (22:11 +0000)]
MIPS: crypto: Add crc32 and crc32c hw accelerated module
This module registers crc32 and crc32c algorithms that use the
optional CRC32[bhwd] and CRC32C[bhwd] instructions in MIPSr6 cores.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@mips.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Patchwork: https://patchwork.linux-mips.org/patch/18601/
[jhogan@kernel.org: Add CRYPTO_ALG_OPTIONAL_KEY flag on Eric Biggers'
suggestion, due to commit
a208fa8f3303 ("crypto: hash - annotate
algorithms taking optional key") in v4.16-rc1]
Marcin Nowakowski [Fri, 9 Feb 2018 22:11:05 +0000 (22:11 +0000)]
MIPS: Add crc instruction support flag to elf_hwcap
Indicate that CRC32 and CRC32C instuctions are supported by the CPU
through elf_hwcap flags.
This will be used by a follow-up commit that introduces crc32(c) crypto
acceleration modules and is required by GENERIC_CPU_AUTOPROBE feature.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@mips.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18600/
Mathieu Malaterre [Tue, 2 Jan 2018 18:53:15 +0000 (19:53 +0100)]
MIPS: Remove a warning when PHYS_OFFSET is 0x0
Rewrite the comparison in `else if` statement, case where `min_low_pfn >
ARCH_PFN_OFFSET` has already been checked in the first `if` statement:
if (min_low_pfn > ARCH_PFN_OFFSET) {
Fix non-fatal warning during compilation using W=1:
arch/mips/kernel/setup.c: In function ‘bootmem_init’:
arch/mips/kernel/setup.c:461:25: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
} else if (min_low_pfn < ARCH_PFN_OFFSET) {
^
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18176/
Signed-off-by: James Hogan <jhogan@kernel.org>
Mathieu Malaterre [Tue, 2 Jan 2018 18:52:21 +0000 (19:52 +0100)]
MIPS: Make declaration for function `memory_region_available` static
Fix non-fatal warning during compilation using W=1:
arch/mips/kernel/setup.c:158:13: warning: no previous prototype for ‘memory_region_available’ [-Wmissing-prototypes]
bool __init memory_region_available(phys_addr_t start, phys_addr_t size)
^~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18175/
[jhogan@kernel.org: tweak whitespace]
Signed-off-by: James Hogan <jhogan@kernel.org>
Mathieu Malaterre [Wed, 24 Jan 2018 11:42:08 +0000 (12:42 +0100)]
MIPS: dts: Fix a typo in the node unit name
The unit name was 8c00000 but since the reg property is declared as:
reg = <0x0 0x4c00000 0x1 0xfb400000>;
the unit name should have been instead 4c00000.
Tested on MIPS Creator CI20 (v1):
$ cat /sys/firmware/devicetree/.../partitions/partition@4c00000/label;echo
system
Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18529/
Signed-off-by: James Hogan <jhogan@kernel.org>
Mathieu Malaterre [Wed, 24 Jan 2018 11:42:07 +0000 (12:42 +0100)]
MIPS: dts: Remove leading 0x and 0s from bindings notation
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were
resolved, namely setting unit-address to lower case, and adding a
whitespace before the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit
4c9847b7375a ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18528/
Signed-off-by: James Hogan <jhogan@kernel.org>
Arvind Yadav [Tue, 26 Dec 2017 06:33:10 +0000 (12:03 +0530)]
MIPS: TXX9: Constify gpio_led
gpio_leds are not supposed to change at runtime. struct
gpio_led_platform_data contains a const struct gpio_led pointer since
v2.6.39, so mark the gpio_led structures const too.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18008/
[jhogan@kernel.org: improve commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
Arvind Yadav [Tue, 26 Dec 2017 06:33:09 +0000 (12:03 +0530)]
MIPS: AR7: Constify gpio_led
gpio_leds are not supposed to change at runtime. struct
gpio_led_platform_data contains a const struct gpio_led pointer since
v2.6.39, so mark the gpio_led structures const too.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18007/
[jhogan@kernel.org: improve commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
Arvind Yadav [Tue, 26 Dec 2017 06:33:08 +0000 (12:03 +0530)]
MIPS: Alchemy: Constify gpio_led
gpio_leds are not supposed to change at runtime. struct
gpio_led_platform_data contains a const struct gpio_led pointer since
v2.6.39, so mark the gpio_led structures const too.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18006/
[jhogan@kernel.org: improve commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
Pravin Shedge [Sun, 10 Dec 2017 18:20:17 +0000 (23:50 +0530)]
MIPS: Remove duplicate includes
These duplicate includes have been found with scripts/checkincludes.pl
but they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17920/
Signed-off-by: James Hogan <jhogan@kernel.org>
Jaedon Shin [Wed, 7 Feb 2018 02:36:27 +0000 (11:36 +0900)]
MIPS: BMIPS: Enable CONFIG_SOC_BRCMSTB
Enable CONFIG_SOC_BRCMSTB in bmips_stb_defconfig. CONFIG_BRCMSTB_PM is
also enabled by default option in Kconfig.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Reviewed-by: James Hogan <jhogan@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/18590/
Signed-off-by: James Hogan <jhogan@kernel.org>
Joe Perches [Wed, 6 Dec 2017 07:04:58 +0000 (23:04 -0800)]
MIPS: Octeon: Fix logging messages with spurious periods after newlines
Using a period after a newline causes bad output.
Fixes:
64b139f97c01 ("MIPS: OCTEON: irq: add CIB and other fixes")
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17886/
Signed-off-by: James Hogan <jhogan@kernel.org>
Linus Torvalds [Mon, 19 Feb 2018 01:29:42 +0000 (17:29 -0800)]
Linux 4.16-rc2
Linus Torvalds [Sun, 18 Feb 2018 20:56:41 +0000 (12:56 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 Kconfig fixes from Thomas Gleixner:
"Three patchlets to correct HIGHMEM64G and CMPXCHG64 dependencies in
Kconfig when CPU selections are explicitely set to M586 or M686"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Linus Torvalds [Sun, 18 Feb 2018 20:38:40 +0000 (12:38 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Perf tool updates and kprobe fixes:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf
top' using it, making it bearable to use it in large core count
systems such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the
syscall table id -> string tables used by 'perf trace' (Hendrik
Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William
Cohen)
- Improve error handling and error propagation of ftrace based
kprobes so failures when installing kprobes are not silently
ignored and create disfunctional tracepoints"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
kprobes: Propagate error from disarm_kprobe_ftrace()
kprobes: Propagate error from arm_kprobe_ftrace()
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
perf s390: Rework system call table creation by using syscall.tbl
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
perf data: Document missing --force option
perf tools: Substitute yet another strtoull()
perf top: Check the latency of perf_top__mmap_read()
perf top: Switch default mode to overwrite mode
perf top: Remove lost events checking
perf hists browser: Add parameter to disable lost event warning
perf top: Add overwrite fall back
perf evsel: Expose the perf_missing_features struct
perf top: Check per-event overwrite term
perf mmap: Discard legacy interface for mmap read
perf test: Update mmap read functions for backward-ring-buffer test
perf mmap: Introduce perf_mmap__read_event()
perf mmap: Introduce perf_mmap__read_done()
...
Linus Torvalds [Sun, 18 Feb 2018 20:22:04 +0000 (12:22 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"A small set of updates mostly for irq chip drivers:
- MIPS GIC fix for spurious, masked interrupts
- fix for a subtle IPI bug in GICv3
- do not probe GICv3 ITSs that are marked as disabled
- multi-MSI support for GICv2m
- various small cleanups"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Re-use DEFINE_SHOW_ATTRIBUTE() macro
irqchip/bcm: Remove hashed address printing
irqchip/gic-v2m: Add PCI Multi-MSI support
irqchip/gic-v3: Ignore disabled ITS nodes
irqchip/gic-v3: Use wmb() instead of smb_wmb() in gic_raise_softirq()
irqchip/gic-v3: Change pr_debug message to pr_devel
irqchip/mips-gic: Avoid spuriously handling masked interrupts
Linus Torvalds [Sun, 18 Feb 2018 19:54:22 +0000 (11:54 -0800)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fix from Thomas Gleixner:
"A small fix which adds the missing for_each_cpu_wrap() stub for the UP
case to avoid build failures"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpumask: Make for_each_cpu_wrap() available on UP as well
Linus Torvalds [Sat, 17 Feb 2018 18:20:47 +0000 (10:20 -0800)]
Merge tag 'for-linus-
20180217' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith, with fixes all over the map for nvme.
From various folks.
- Classic polling fix, that avoids a latency issue where we still end
up waiting for an interrupt in some cases. From Nitesh Shetty.
- Comment typo fix from Minwoo Im.
* tag 'for-linus-
20180217' of git://git.kernel.dk/linux-block:
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
nvme-rdma: fix sysfs invoked reset_ctrl error flow
nvmet: Change return code of discard command if not supported
nvme-pci: Fix timeouts in connecting state
nvme-pci: Remap CMB SQ entries on every controller reset
nvme: fix the deadlock in nvme_update_formats
blk: optimization for classic polling
nvme: Don't use a stack buffer for keep-alive command
nvme_fc: cleanup io completion
nvme_fc: correct abort race condition on resets
nvme: Fix discard buffer overrun
nvme: delete NVME_CTRL_LIVE --> NVME_CTRL_CONNECTING transition
nvme-rdma: use NVME_CTRL_CONNECTING state to mark init process
nvme: rename NVME_CTRL_RECONNECTING state to NVME_CTRL_CONNECTING
Linus Torvalds [Sat, 17 Feb 2018 18:08:28 +0000 (10:08 -0800)]
Merge tag 'mmc-v4.16-rc1' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- meson-gx: Revert to earlier tuning process
- bcm2835: Don't overwrite max frequency unconditionally
* tag 'mmc-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: bcm2835: Don't overwrite max frequency unconditionally
Revert "mmc: meson-gx: include tx phase in the tuning process"
Linus Torvalds [Sat, 17 Feb 2018 18:06:13 +0000 (10:06 -0800)]
Merge tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- add missing dependency to NAND_MARVELL Kconfig entry
- use the appropriate OOB layout in the VF610 driver
* tag 'mtd/fixes-for-4.16-rc2' of git://git.infradead.org/linux-mtd:
mtd: nand: MTD_NAND_MARVELL should depend on HAS_DMA
mtd: nand: vf610: set correct ooblayout
Linus Torvalds [Sat, 17 Feb 2018 17:48:26 +0000 (09:48 -0800)]
Merge tag 'powerpc-4.16-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The main attraction is a fix for a bug in the new drmem code, which
was causing an oops on boot on some versions of Qemu.
There's also a fix for XIVE (Power9 interrupt controller) on KVM, as
well as a few other minor fixes.
Thanks to: Corentin Labbe, Cyril Bur, Cédric Le Goater, Daniel Black,
Nathan Fontenot, Nicholas Piggin"
* tag 'powerpc-4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
powerpc/pseries: Add empty update_numa_cpu_lookup_table() for NUMA=n
powerpc/powernv: IMC fix out of bounds memory access at shutdown
powerpc/xive: Use hw CPU ids when configuring the CPU queues
powerpc: Expose TSCR via sysfs only on powernv
Linus Torvalds [Sat, 17 Feb 2018 17:46:18 +0000 (09:46 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"The bulk of this is the pte accessors annotation to READ/WRITE_ONCE
(we tried to avoid pushing this during the merge window to avoid
conflicts)
- Updated the page table accessors to use READ/WRITE_ONCE and prevent
compiler transformation that could lead to an apparent loss of
coherency
- Enabled branch predictor hardening for the Falkor CPU
- Fix interaction between kpti enabling and KASan causing the
recursive page table walking to take a significant time
- Fix some sparse warnings"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cputype: Silence Sparse warnings
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
arm64: proc: Set PTE_NG for table entries to avoid traversing them twice
arm64: Add missing Falkor part number for branch predictor hardening
Linus Torvalds [Sat, 17 Feb 2018 17:16:09 +0000 (09:16 -0800)]
Merge tag 'for-linus-4.16a-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fixes for the Xen pvcalls frontend driver
- fix for booting Xen pv domains
- fix for the xenbus driver user interface
* tag 'for-linus-4.16a-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
pvcalls-front: wait for other operations to return when release passive sockets
pvcalls-front: introduce a per sock_mapping refcount
x86/xen: Calculate __max_logical_packages on PV domains
xenbus: track caller request id
Stefano Stabellini [Wed, 14 Feb 2018 18:28:24 +0000 (10:28 -0800)]
pvcalls-front: wait for other operations to return when release passive sockets
Passive sockets can have ongoing operations on them, specifically, we
have two wait_event_interruptable calls in pvcalls_front_accept.
Add two wake_up calls in pvcalls_front_release, then wait for the
potential waiters to return and release the sock_mapping refcount.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Stefano Stabellini [Wed, 14 Feb 2018 18:28:23 +0000 (10:28 -0800)]
pvcalls-front: introduce a per sock_mapping refcount
Introduce a per sock_mapping refcount, in addition to the existing
global refcount. Thanks to the sock_mapping refcount, we can safely wait
for it to be 1 in pvcalls_front_release before freeing an active socket,
instead of waiting for the global refcount to be 1.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Prarit Bhargava [Wed, 7 Feb 2018 23:49:23 +0000 (18:49 -0500)]
x86/xen: Calculate __max_logical_packages on PV domains
The kernel panics on PV domains because native_smp_cpus_done() is
only called for HVM domains.
Calculate __max_logical_packages for PV domains.
Fixes:
b4c0a7326f5d ("x86/smpboot: Fix __max_logical_packages estimate")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Tested-and-reported-by: Simon Gaiser <simon@invisiblethingslab.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: xen-devel@lists.xenproject.org
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Joao Martins [Fri, 2 Feb 2018 17:42:33 +0000 (17:42 +0000)]
xenbus: track caller request id
Commit
fd8aa9095a95 ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Cc: <stable@vger.kernel.org> # 4.11
Fixes:
fd8aa9095a ("xen: optimize xenbus driver for multiple concurrent xenstore accesses")
Reported-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Robin Murphy [Fri, 16 Feb 2018 17:04:23 +0000 (17:04 +0000)]
arm64: cputype: Silence Sparse warnings
Sparse makes a fair bit of noise about our MPIDR mask being implicitly
long - let's explicitly describe it as such rather than just relying on
the value forcing automatic promotion.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 16 Feb 2018 20:22:33 +0000 (12:22 -0800)]
Merge tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"A few dma-mapping fixes for the fallout from the changes in rc1"
* tag 'dma-mapping-4.16-2' of git://git.infradead.org/users/hch/dma-mapping:
powerpc/macio: set a proper dma_coherent_mask
dma-mapping: fix a comment typo
dma-direct: comment the dma_direct_free calling convention
dma-direct: mark as is_phys
ia64: fix build failure with CONFIG_SWIOTLB
Will Deacon [Thu, 15 Feb 2018 11:14:56 +0000 (11:14 +0000)]
arm64: mm: Use READ_ONCE/WRITE_ONCE when accessing page tables
In many cases, page tables can be accessed concurrently by either another
CPU (due to things like fast gup) or by the hardware page table walker
itself, which may set access/dirty bits. In such cases, it is important
to use READ_ONCE/WRITE_ONCE when accessing page table entries so that
entries cannot be torn, merged or subject to apparent loss of coherence
due to compiler transformations.
Whilst there are some scenarios where this cannot happen (e.g. pinned
kernel mappings for the linear region), the overhead of using READ_ONCE
/WRITE_ONCE everywhere is minimal and makes the code an awful lot easier
to reason about. This patch consistently uses these macros in the arch
code, as well as explicitly namespacing pointers to page table entries
from the entries themselves by using adopting a 'p' suffix for the former
(as is sometimes used elsewhere in the kernel source).
Tested-by: Yury Norov <ynorov@caviumnetworks.com>
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Arnd Bergmann [Fri, 16 Feb 2018 15:25:53 +0000 (16:25 +0100)]
mm: hide a #warning for COMPILE_TEST
We get a warning about some slow configurations in randconfig kernels:
mm/memory.c:83:2: error: #warning Unfortunate NUMA and NUMA Balancing config, growing page-frame for last_cpupid. [-Werror=cpp]
The warning is reasonable by itself, but gets in the way of randconfig
build testing, so I'm hiding it whenever CONFIG_COMPILE_TEST is set.
The warning was added in 2013 in commit
75980e97dacc ("mm: fold
page->_last_nid into page->flags where possible").
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Feb 2018 17:31:37 +0000 (09:31 -0800)]
Merge tag 'mips_fixes_4.16_2' of git://git./linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"A few fixes for outstanding MIPS issues:
- an __init section mismatch warning when brcmstb_pm is enabled
- a regression handling multiple mem=X@Y arguments (4.11)
- a USB Kconfig select warning, and related sparc cleanup (4.16)"
* tag 'mips_fixes_4.16_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
sparc,leon: Select USB_UHCI_BIG_ENDIAN_{MMIO,DESC}
usb: Move USB_UHCI_BIG_ENDIAN_* out of USB_SUPPORT
MIPS: Fix incorrect mem=X@Y handling
MIPS: BMIPS: Fix section mismatch warning
Linus Torvalds [Fri, 16 Feb 2018 17:26:18 +0000 (09:26 -0800)]
Merge tag 'for-4.16-rc1-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"We have a few assorted fixes, some of them show up during fstests so I
gave them more testing"
* tag 'for-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Fix use-after-free when cleaning up fs_devs with a single stale device
Btrfs: fix null pointer dereference when replacing missing device
btrfs: remove spurious WARN_ON(ref->count < 0) in find_parent_nodes
btrfs: Ignore errors from btrfs_qgroup_trace_extent_post
Btrfs: fix unexpected -EEXIST when creating new inode
Btrfs: fix use-after-free on root->orphan_block_rsv
Btrfs: fix btrfs_evict_inode to handle abnormal inodes correctly
Btrfs: fix extent state leak from tree log
Btrfs: fix crash due to not cleaning up tree log block's dirty bits
Btrfs: fix deadlock in run_delalloc_nocow
Linus Torvalds [Fri, 16 Feb 2018 17:23:36 +0000 (09:23 -0800)]
Merge tag 'for-4.16/dm-chained-bios-fix' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix for DM core to properly propagate errors (avoids overriding
non-zero error with 0). This is particularly important given DM core's
increased use of chained bios"
* tag 'for-4.16/dm-chained-bios-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: correctly handle chained bios in dec_pending()
Linus Torvalds [Fri, 16 Feb 2018 17:20:00 +0000 (09:20 -0800)]
Merge tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- regression fix in keyboard support for Dell laptops
- prevent out-of-boundary write in WMI bus driver
- increase timeout to read functional key status on Lenovo laptops
* tag 'platform-drivers-x86-v4.16-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-laptop: Removed duplicates in DMI whitelist
platform/x86: dell-laptop: fix kbd_get_state's request value
platform/x86: ideapad-laptop: Increase timeout to wait for EC answer
platform/x86: wmi: fix off-by-one write in wmi_dev_probe()
Linus Torvalds [Fri, 16 Feb 2018 17:11:30 +0000 (09:11 -0800)]
Merge tag 'sound-4.16-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of usual suspects:
- a handful USB-audio and HD-audio device-specific quirks
- some trivial fixes for the new AC97 bus stuff
- another race fix in ALSA sequencer core"
* tag 'sound-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: PCI quirk for Fujitsu U7x7
ALSA: seq: Fix racy pool initializations
ALSA: usb: add more device quirks for USB DSD devices
ALSA: usb-audio: Fix UAC2 get_ctl request with a RANGE attribute
ALSA: ac97: Fix copy and paste typo in documentation
ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204
ALSA: ac97: kconfig: Remove select of undefined symbol AC97
ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform
ALSA: hda/realtek - Add headset mode support for Dell laptop
ALSA: hda - Fix headset mic detection problem for two Dell machines
Linus Torvalds [Fri, 16 Feb 2018 17:08:59 +0000 (09:08 -0800)]
Merge tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One nouveau regression fix, one AMD quirk and a full set of i915
fixes.
The i915 fixes are mostly for things caught by their CI system, main
ones being DSI panel fixes and GEM fixes"
* tag 'drm-fixes-for-v4.16-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: Make clock gate support conditional
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
drm/amdgpu: add new device to use atpx quirk
NeilBrown [Thu, 15 Feb 2018 09:00:15 +0000 (20:00 +1100)]
dm: correctly handle chained bios in dec_pending()
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit
18a25da84354 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com>
Cc: stable@vger.kernel.org (v3.14+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Thomas Gleixner [Fri, 16 Feb 2018 14:47:26 +0000 (15:47 +0100)]
Merge tag 'irqchip-4.16-2' of git://git./linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.16-rc2 from Marc Zyngier
- A MIPS GIC fix for spurious, masked interrupts
- A fix for a subtle IPI bug in GICv3
- Do not probe GICv3 ITSs that are marked as disabled
- Multi-MSI support for GICv2m
- Various cleanups
Andy Shevchenko [Wed, 14 Feb 2018 15:47:35 +0000 (17:47 +0200)]
irqdomain: Re-use DEFINE_SHOW_ATTRIBUTE() macro
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Jaedon Shin [Mon, 12 Feb 2018 02:18:12 +0000 (11:18 +0900)]
irqchip/bcm: Remove hashed address printing
Since commit
ad67b74d2469 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful. so delete the prints.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Marc Zyngier [Tue, 6 Feb 2018 18:55:33 +0000 (18:55 +0000)]
irqchip/gic-v2m: Add PCI Multi-MSI support
We'd never implemented Multi-MSI support with GICv2m, because
it is weird and clunky, and you'd think people would rather use
MSI-X.
Turns out there is still plenty of devices out there that rely
on Multi-MSI. Oh well, let's teach that trick to the v2m widget,
it is not a big deal anyway.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Stephen Boyd [Thu, 1 Feb 2018 17:03:29 +0000 (09:03 -0800)]
irqchip/gic-v3: Ignore disabled ITS nodes
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Shanker Donthineni [Thu, 1 Feb 2018 00:03:42 +0000 (18:03 -0600)]
irqchip/gic-v3: Use wmb() instead of smb_wmb() in gic_raise_softirq()
A DMB instruction can be used to ensure the relative order of only
memory accesses before and after the barrier. Since writes to system
registers are not memory operations, barrier DMB is not sufficient
for observability of memory accesses that occur before ICC_SGI1R_EL1
writes.
A DSB instruction ensures that no instructions that appear in program
order after the DSB instruction, can execute until the DSB instruction
has completed.
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>,
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Mark Salter [Fri, 2 Feb 2018 14:20:29 +0000 (09:20 -0500)]
irqchip/gic-v3: Change pr_debug message to pr_devel
The pr_debug() in gic-v3 gic_send_sgi() can trigger a circular locking
warning:
GICv3: CPU10: ICC_SGI1R_EL1 5000400
======================================================
WARNING: possible circular locking dependency detected
4.15.0+ #1 Tainted: G W
------------------------------------------------------
dynamic_debug01/1873 is trying to acquire lock:
((console_sem).lock){-...}, at: [<
0000000099c891ec>] down_trylock+0x20/0x4c
but task is already holding lock:
(&rq->lock){-.-.}, at: [<
00000000842e1587>] __task_rq_lock+0x54/0xdc
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&rq->lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock+0x4c/0x60
task_fork_fair+0x3c/0x148
sched_fork+0x10c/0x214
copy_process.isra.32.part.33+0x4e8/0x14f0
_do_fork+0xe8/0x78c
kernel_thread+0x48/0x54
rest_init+0x34/0x2a4
start_kernel+0x45c/0x488
-> #1 (&p->pi_lock){-.-.}:
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
try_to_wake_up+0x48/0x600
wake_up_process+0x28/0x34
__up.isra.0+0x60/0x6c
up+0x60/0x68
__up_console_sem+0x4c/0x7c
console_unlock+0x328/0x634
vprintk_emit+0x25c/0x390
dev_vprintk_emit+0xc4/0x1fc
dev_printk_emit+0x88/0xa8
__dev_printk+0x58/0x9c
_dev_info+0x84/0xa8
usb_new_device+0x100/0x474
hub_port_connect+0x280/0x92c
hub_event+0x740/0xa84
process_one_work+0x240/0x70c
worker_thread+0x60/0x400
kthread+0x110/0x13c
ret_from_fork+0x10/0x18
-> #0 ((console_sem).lock){-...}:
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
other info that might help us debug this:
Chain exists of:
(console_sem).lock --> &p->pi_lock --> &rq->lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&rq->lock);
lock(&p->pi_lock);
lock(&rq->lock);
lock((console_sem).lock);
*** DEADLOCK ***
2 locks held by dynamic_debug01/1873:
#0: (&p->pi_lock){-.-.}, at: [<
000000001366df53>] wake_up_new_task+0x40/0x470
#1: (&rq->lock){-.-.}, at: [<
00000000842e1587>] __task_rq_lock+0x54/0xdc
stack backtrace:
CPU: 10 PID: 1873 Comm: dynamic_debug01 Tainted: G W 4.15.0+ #1
Hardware name: GIGABYTE R120-T34-00/MT30-GS2-00, BIOS T48 10/02/2017
Call trace:
dump_backtrace+0x0/0x188
show_stack+0x24/0x2c
dump_stack+0xa4/0xe0
print_circular_bug.isra.31+0x29c/0x2b8
check_prev_add.constprop.39+0x6c8/0x6dc
validate_chain.isra.34+0x6e4/0xa20
__lock_acquire+0x3b4/0x6e0
lock_acquire+0xf4/0x2a8
_raw_spin_lock_irqsave+0x58/0x70
down_trylock+0x20/0x4c
__down_trylock_console_sem+0x3c/0x9c
console_trylock+0x20/0xb0
vprintk_emit+0x254/0x390
vprintk_default+0x58/0x90
vprintk_func+0xbc/0x164
printk+0x80/0xa0
__dynamic_pr_debug+0x84/0xac
gic_raise_softirq+0x184/0x18c
smp_cross_call+0xac/0x218
smp_send_reschedule+0x3c/0x48
resched_curr+0x60/0x9c
check_preempt_curr+0x70/0xdc
wake_up_new_task+0x310/0x470
_do_fork+0x188/0x78c
SyS_clone+0x44/0x50
__sys_trace_return+0x0/0x4
GICv3: CPU0: ICC_SGI1R_EL1 12000
This could be fixed with printk_deferred() but that might lessen its
usefulness for debugging. So change it to pr_devel to keep it out of
production kernels. Developers working on gic-v3 can enable it as
needed in their kernels.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Matt Redfearn [Mon, 5 Feb 2018 16:45:36 +0000 (16:45 +0000)]
irqchip/mips-gic: Avoid spuriously handling masked interrupts
Commit
7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
[ 5.058454] irq 13, desc:
ffffffff80a7ad80, depth: 1, count: 0, unhandled: 0
[ 5.062057] ->handle_irq():
ffffffff801b1838,
[ 5.062175] handle_bad_irq+0x0/0x2c0
Where IRQ 13 is the UART interrupt.
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org
Fixes:
7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Nathan Fontenot [Fri, 16 Feb 2018 03:27:41 +0000 (21:27 -0600)]
powerpc/pseries: Check for zero filled ibm,dynamic-memory property
Some versions of QEMU will produce an ibm,dynamic-reconfiguration-memory
node with a ibm,dynamic-memory property that is zero-filled. This
causes the drmem code to oops trying to parse this property.
The fix for this is to validate that the property does contain LMB
entries before trying to parse it and bail if the count is zero.
Oops: Kernel access of bad area, sig: 11 [#1]
DAR:
0000000000000010
NIP read_drconf_v1_cell+0x54/0x9c
LR read_drconf_v1_cell+0x48/0x9c
Call Trace:
__param_initcall_debug+0x0/0x28 (unreliable)
drmem_init+0x144/0x2f8
do_one_initcall+0x64/0x1d0
kernel_init_freeable+0x298/0x38c
kernel_init+0x24/0x160
ret_from_kernel_thread+0x5c/0xb4
The ibm,dynamic-reconfiguration-memory device tree property generated
that causes this:
ibm,dynamic-reconfiguration-memory {
ibm,lmb-size = <0x0 0x10000000>;
ibm,memory-flags-mask = <0xff>;
ibm,dynamic-memory = <0x0 0x0 0x0 0x0 0x0 0x0>;
linux,phandle = <0x7e57eed8>;
ibm,associativity-lookup-arrays = <0x1 0x4 0x0 0x0 0x0 0x0>;
ibm,memory-preservation-time = <0x0>;
};
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Tested-by: Daniel Black <daniel@linux.vnet.ibm.com>
[mpe: Trim oops report]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Kelley [Wed, 14 Feb 2018 02:54:03 +0000 (02:54 +0000)]
cpumask: Make for_each_cpu_wrap() available on UP as well
for_each_cpu_wrap() was originally added in the #else half of a
large "#if NR_CPUS == 1" statement, but was omitted in the #if
half. This patch adds the missing #if half to prevent compile
errors when NR_CPUS is 1.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michael Kelley <mhkelley@outlook.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kys@microsoft.com
Cc: martin.petersen@oracle.com
Cc: mikelley@microsoft.com
Fixes:
c743f0a5c50f ("sched/fair, cpumask: Export for_each_cpu_wrap()")
Link: http://lkml.kernel.org/r/SN6PR1901MB2045F087F59450507D4FCC17CBF50@SN6PR1901MB2045.namprd19.prod.outlook.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matthew Whitehead [Thu, 15 Feb 2018 16:54:56 +0000 (11:54 -0500)]
x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig
The X86_P6_NOP config class leaves out many i686-class CPUs. Instead,
explicitly enumerate all these CPUs.
Using a configuration with M686 currently sets X86_MINIMUM_CPU_FAMILY=5
instead of the correct value of 6.
Booting on an i586 it will fail to generate the "This kernel
requires an i686 CPU, but only detected an i586 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i686-specific instructions.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-3-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matthew Whitehead [Thu, 15 Feb 2018 16:54:55 +0000 (11:54 -0500)]
x86/Kconfig: Exclude i586-class CPUs lacking PAE support from the HIGHMEM64G Kconfig group
i586-class machines also lack support for Physical Address Extension (PAE),
so add them to the exclusion list.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-2-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Matthew Whitehead [Thu, 15 Feb 2018 16:54:54 +0000 (11:54 -0500)]
x86/Kconfig: Add missing i586-class CPUs to the X86_CMPXCHG64 Kconfig group
Several i586-class CPUs supporting this instruction are missing from
the X86_CMPXCHG64 config group.
Using a configuration with either M586TSC or M586MMX currently sets
X86_MINIMUM_CPU_FAMILY=4 instead of the correct value of 5.
Booting on an i486 it will fail to generate the "This kernel
requires an i586 CPU, but only detected an i486 CPU" message and
intentional halt as expected. It will instead just silently hang
when it hits i586-specific instructions.
The M586 CPU is not in this list because at least the Cyrix 5x86
lacks this instruction, and perhaps others.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1518713696-11360-1-git-send-email-tedheadster@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:24 +0000 (00:51 +0100)]
kprobes: Propagate error from disarm_kprobe_ftrace()
Improve error handling when disarming ftrace-based kprobes. Like with
arm_kprobe_ftrace(), propagate any errors from disarm_kprobe_ftrace() so
that we do not disable/unregister kprobes that are still armed. In other
words, unregister_kprobe() and disable_kprobe() should not report success
if the kprobe could not be disarmed.
disarm_all_kprobes() keeps its current behavior and attempts to
disarm all kprobes. It returns the last encountered error and gives a
warning if not all probes could be disarmed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/20180109235124.30886-3-jeyu@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jessica Yu [Tue, 9 Jan 2018 23:51:23 +0000 (00:51 +0100)]
kprobes: Propagate error from arm_kprobe_ftrace()
Improve error handling when arming ftrace-based kprobes. Specifically, if
we fail to arm a ftrace-based kprobe, register_kprobe()/enable_kprobe()
should report an error instead of success. Previously, this has lead to
confusing situations where register_kprobe() would return 0 indicating
success, but the kprobe would not be functional if ftrace registration
during the kprobe arming process had failed. We should therefore take any
errors returned by ftrace into account and propagate this error so that we
do not register/enable kprobes that cannot be armed. This can happen if,
for example, register_ftrace_function() finds an IPMODIFY conflict (since
kprobe_ftrace_ops has this flag set) and returns an error. Such a conflict
is possible since livepatches also set the IPMODIFY flag for their ftrace_ops.
arm_all_kprobes() keeps its current behavior and attempts to arm all
kprobes. It returns the last encountered error and gives a warning if
not all probes could be armed.
This patch is based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:
https://lkml.org/lkml/2015/2/26/452
However, further work on this had been paused since then and the patches
were not upstreamed.
Based-on-patches-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/20180109235124.30886-2-jeyu@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Fri, 16 Feb 2018 08:10:09 +0000 (09:10 +0100)]
Merge tag 'perf-core-for-mingo-4.17-
20180215' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/core fixes from Arnaldo Carvalho de Melo:
- perf_mmap overwrite mode fixes/overhaul, prep work to get 'perf top'
using it, making it bearable to use it in large core count systems
such as Knights Landing/Mill Intel systems (Kan Liang)
- s/390 now uses syscall.tbl, just like x86-64 to generate the syscall
table id -> string tables used by 'perf trace' (Hendrik Brueckner)
- Use strtoull() instead of home grown function (Andy Shevchenko)
- Synchronize kernel ABI headers, v4.16-rc1 (Ingo Molnar)
- Document missing 'perf data --force' option (Sangwon Hong)
- Add perf vendor JSON metrics for ARM Cortex-A53 Processor (William Cohen)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Fri, 16 Feb 2018 04:26:01 +0000 (14:26 +1000)]
Merge branch 'linux-4.16' of git://github.com/skeggsb/linux into drm-fixes
single fix for older gpus.
* 'linux-4.16' of git://github.com/skeggsb/linux:
drm/nouveau: Make clock gate support conditional
Thierry Reding [Wed, 7 Feb 2018 17:40:27 +0000 (18:40 +0100)]
drm/nouveau: Make clock gate support conditional
The recently introduced clock gate support breaks on Tegra chips because
no thermal support is enabled for those devices. Conditionalize the code
on the existence of thermal support to fix this.
Fixes:
b138eca661cc ("drm/nouveau: Add support for basic clockgating on Kepler1")
Cc: Martin Peres <martin.peres@free.fr>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Dave Airlie [Fri, 16 Feb 2018 02:33:03 +0000 (12:33 +1000)]
Merge tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
There are important fixes for VLV with MIPI/DSI panels,
2 clean-up patches needed for this MIPI/DSI fix,
and many fixes for GEM including fixes for Perf OA and PMU,
and fixes on scheduler and preemption.
This also includes GVT fixes: "This has one to fix GTT mmio 8b
access from guest and two simple ones for mmio switch and typo fix"
* tag 'drm-intel-fixes-2018-02-14-1' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Fix DSI panels with v1 MIPI sequences without a DEASSERT sequence v3
drm/i915: Free memdup-ed DSI VBT data structures on driver_unload
drm/i915: Add intel_bios_cleanup() function
drm/i915/vlv: Add cdclk workaround for DSI
drm/i915/gvt: fix one typo of render_mmio trace
drm/i915/gvt: Support BAR0 8-byte reads/writes
drm/i915/gvt: add 0xe4f0 into gen9 render list
drm/i915/pmu: Fix building without CONFIG_PM
drm/i915/pmu: Fix sleep under atomic in RC6 readout
drm/i915/pmu: Fix PMU enable vs execlists tasklet race
drm/i915: Lock out execlist tasklet while peeking inside for busy-stats
drm/i915/breadcrumbs: Ignore unsubmitted signalers
drm/i915: Don't wake the device up to check if the engine is asleep
drm/i915: Avoid truncation before clamping userspace's priority value
drm/i915/perf: Fix compiler warning for string truncation
drm/i915/perf: Fix compiler warning for string truncation
Dave Airlie [Fri, 16 Feb 2018 02:30:41 +0000 (12:30 +1000)]
Merge branch 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
single atpx fix
* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: add new device to use atpx quirk
Linus Torvalds [Thu, 15 Feb 2018 22:50:32 +0000 (14:50 -0800)]
Merge tag 'acpi-4.16-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a system resume regression from the 4.13 cycle, clean up
device table handling in the ACPI core, update sysfs ABI documentation
of a couple of drivers and add an expected switch fall-through marker
to the SPCR table parsing code.
Specifics:
- Revert a problematic EC driver change from the 4.13 cycle that
introduced a system resume regression on Thinkpad X240 (Rafael
Wysocki).
- Clean up device tables handling in the ACPI core and the related
part of the device properties framework (Andy Shevchenko).
- Update the sysfs ABI documentatio of the dock and the INT3407
special device drivers (Aishwarya Pant).
- Add an expected switch fall-through marker to the SPCR table
parsing code (Gustavo Silva)"
* tag 'acpi-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: dock: document sysfs interface
ACPI / DPTF: Document dptf_power sysfs atttributes
device property: Constify device_get_match_data()
ACPI / bus: Rename acpi_get_match_data() to acpi_device_get_match_data()
ACPI / bus: Remove checks in acpi_get_match_data()
ACPI / bus: Do not traverse through non-existed device table
ACPI: SPCR: Mark expected switch fall-through in acpi_parse_spcr
ACPI / EC: Restore polling during noirq suspend/resume phases
Linus Torvalds [Thu, 15 Feb 2018 22:40:01 +0000 (14:40 -0800)]
Merge tag 'pm-4.16-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a recently introduced build issue related to cpuidle and two
bugs in the PM core, update cpuidle documentation and clean up memory
allocations in the operating performance points (OPP) framework.
Specifics:
- Fix a recently introduced build issue related to cpuidle by
covering all of the relevant combinations of Kconfig options
in its header (Rafael Wysocki).
- Add missing invocation of pm_runtime_drop_link() to the
!CONFIG_SRCU variant of __device_link_del() (Lukas Wunner).
- Fix unbalanced IRQ enable in the wakeup interrupts framework
(Tony Lindgren).
- Update cpuidle sysfs ABI documentation (Aishwarya Pant).
- Use GFP_KERNEL instead of GFP_ATOMIC for allocating memory
in dev_pm_opp_init_cpufreq_table() (Jia-Ju Bai)"
* tag 'pm-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: cpuidle: Fix cpuidle_poll_state_init() prototype
PM / runtime: Update links_count also if !CONFIG_SRCU
PM / wakeirq: Fix unbalanced IRQ enable for wakeirq
Documentation/ABI: update cpuidle sysfs documentation
opp: cpu: Replace GFP_ATOMIC with GFP_KERNEL in dev_pm_opp_init_cpufreq_table
Linus Torvalds [Thu, 15 Feb 2018 22:31:28 +0000 (14:31 -0800)]
Merge tag 'hwmon-for-linus-v4.16-rc2' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix bad temperature display on Ryzen/Threadripper"
* tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Only apply temperature offset if result is positive
Linus Torvalds [Thu, 15 Feb 2018 22:29:27 +0000 (14:29 -0800)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"This includes a bugfix for virtio 9p fs. It also fixes hybernation for
s390 guests with virtio devices"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: implement PM operations for virtio_ccw
9p/trans_virtio: discard zero-length reply
James Hogan [Wed, 31 Jan 2018 22:24:46 +0000 (22:24 +0000)]
sparc,leon: Select USB_UHCI_BIG_ENDIAN_{MMIO,DESC}
Now that USB_UHCI_BIG_ENDIAN_MMIO and USB_UHCI_BIG_ENDIAN_DESC are moved
outside of the USB_SUPPORT conditional, simply select them from
SPARC_LEON rather than by the symbol's defaults in drivers/usb/Kconfig,
similar to how it is done for USB_EHCI_BIG_ENDIAN_MMIO and
USB_EHCI_BIG_ENDIAN_DESC.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/18560/
James Hogan [Wed, 31 Jan 2018 22:24:45 +0000 (22:24 +0000)]
usb: Move USB_UHCI_BIG_ENDIAN_* out of USB_SUPPORT
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes:
2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Linus Torvalds [Thu, 15 Feb 2018 17:28:47 +0000 (09:28 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes:
- fix rq->lock lockdep annotation bug
- fix/improve update_curr_rt() and update_curr_dl() accounting
- update documentation
- remove unused macro"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cpufreq: Remove unused SUGOV_KTHREAD_PRIORITY macro
sched/core: Fix DEBUG_SPINLOCK annotation for rq->lock
sched/rt: Make update_curr_rt() more accurate
sched/deadline: Make update_curr_dl() more accurate
membarrier-sync-core: Document architecture support
Linus Torvalds [Thu, 15 Feb 2018 17:05:26 +0000 (09:05 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"This contains two qspinlock fixes and three documentation and comment
fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/semaphore: Update the file path in documentation
locking/atomic/bitops: Document and clarify ordering semantics for failed test_and_{}_bit()
locking/qspinlock: Ensure node->count is updated before initialising node
locking/qspinlock: Ensure node is initialised before updating prev->next
Documentation/locking/mutex-design: Update to reflect latest changes
Minwoo Im [Thu, 15 Feb 2018 14:53:17 +0000 (23:53 +0900)]
block: fix a typo in comment of BLK_MQ_POLL_STATS_BKTS
Update comment typo _consisitent_ to _consistent_ from following commit.
commit
0206319fdfee ("blk-mq: Fix poll_stat for new size-based bucketing.")
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hendrik Brueckner [Thu, 8 Feb 2018 11:47:48 +0000 (12:47 +0100)]
Revert "tools include s390: Grab a copy of arch/s390/include/uapi/asm/unistd.h"
This reverts commit
f120c7b187e6c418238710b48723ce141f467543 which is no
longer required with the introduction of a syscall.tbl on s390.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference:
1518090470-2899-2-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-q1lg0nvhha1tk39ri9aqalcb@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Hendrik Brueckner [Thu, 8 Feb 2018 11:47:50 +0000 (12:47 +0100)]
perf s390: Rework system call table creation by using syscall.tbl
Recently, s390 uses a syscall.tbl input file to generate its system call
table and unistd uapi header files. Hence, update mksyscalltbl to use
it as input to create the system table for perf.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference:
1518090470-2899-4-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-bdyhllhsq1zgxv2qx4m377y6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Hendrik Brueckner [Thu, 8 Feb 2018 11:47:49 +0000 (12:47 +0100)]
perf s390: Grab a copy of arch/s390/kernel/syscall/syscall.tbl
Grab a copy of the s390 system call table file introduced with commit
857f46bfb07f53dc112d69bdfb137cc5ec3da7c5 "s390/syscalls: add system call
table".
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
LPU-Reference:
1518090470-2899-3-git-send-email-brueckner@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-hpw7vdjp7g92ivgpddrp5ydq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ingo Molnar [Tue, 13 Feb 2018 11:54:58 +0000 (12:54 +0100)]
tools/headers: Synchronize kernel ABI headers, v4.16-rc1
Sync the following tooling headers with the latest kernel version:
tools/arch/powerpc/include/uapi/asm/kvm.h
tools/arch/x86/include/asm/cpufeatures.h
tools/include/uapi/drm/i915_drm.h
tools/include/uapi/linux/if_link.h
tools/include/uapi/linux/kvm.h
All the changes are new ABI additions which don't impact their use
in existing tooling.
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Richter [Wed, 17 Jan 2018 08:38:31 +0000 (09:38 +0100)]
perf test: Fix test trace+probe_libc_inet_pton.sh for s390x
On Intel test case trace+probe_libc_inet_pton.sh succeeds and the
output is:
[root@f27 perf]# ./perf trace --no-syscalls
-e probe_libc:inet_pton/max-stack=3/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.037 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.037/0.037/0.037/0.000 ms
0.000 probe_libc:inet_pton:(
7fa40ac618a0))
__GI___inet_pton (/usr/lib64/libc-2.26.so)
getaddrinfo (/usr/lib64/libc-2.26.so)
main (/usr/bin/ping)
The kernel stack unwinder is used, it is specified implicitly
as call-graph=fp (frame pointer).
On s390x only dwarf is available for stack unwinding. It is also
done in user space. This requires different parameter setup
and result checking for s390x and Intel.
This patch adds separate perf trace setup and result checking
for Intel and s390x. On s390x specify this command line to
get a call-graph and handle the different call graph result
checking:
[root@s35lp76 perf]# ./perf trace --no-syscalls
-e probe_libc:inet_pton/call-graph=dwarf/ ping -6 -c 1 ::1
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.041 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.041/0.041/0.041/0.000 ms
0.000 probe_libc:inet_pton:(
3ffb9942060))
__GI___inet_pton (/usr/lib64/libc-2.26.so)
gaih_inet (inlined)
__GI_getaddrinfo (inlined)
main (/usr/bin/ping)
__libc_start_main (/usr/lib64/libc-2.26.so)
_start (/usr/bin/ping)
[root@s35lp76 perf]#
Before:
[root@s8360047 perf]# ./perf test -vv 58
58: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 26349
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.079 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.079/0.079/0.079/0.000 ms
0.000 probe_libc:inet_pton:(
3ff925c2060))
test child finished with -1
---- end ----
probe libc's inet_pton & backtrace it with ping: FAILED!
[root@s8360047 perf]#
After:
[root@s35lp76 perf]# ./perf test -vv 57
57: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 38708
PING ::1(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.038 ms
--- ::1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.038/0.038/0.038/0.000 ms
0.000 probe_libc:inet_pton:(
3ff87342060))
__GI___inet_pton (/usr/lib64/libc-2.26.so)
gaih_inet (inlined)
__GI_getaddrinfo (inlined)
main (/usr/bin/ping)
__libc_start_main (/usr/lib64/libc-2.26.so)
_start (/usr/bin/ping)
test child finished with 0
---- end ----
probe libc's inet_pton & backtrace it with ping: Ok
[root@s35lp76 perf]#
On Intel the test case runs unchanged and succeeds.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180117083831.101001-1-tmricht@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Sangwon Hong [Mon, 5 Feb 2018 11:48:35 +0000 (20:48 +0900)]
perf data: Document missing --force option
Add the --force option to the man page.
Signed-off-by: Sangwon Hong <qpakzk@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Link: http://lkml.kernel.org/r/1517831315-31490-1-git-send-email-qpakzk@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Andy Shevchenko [Mon, 29 Jan 2018 13:03:59 +0000 (15:03 +0200)]
perf tools: Substitute yet another strtoull()
Instead of home grown function let's use what library provides us.
Signed-off-by: Andriy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20180129130359.1490-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:32 +0000 (13:26 -0800)]
perf top: Check the latency of perf_top__mmap_read()
The latency of perf_top__mmap_read() should be lower than refresh time.
If not, give some hints to reduce the latency.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-18-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:31 +0000 (13:26 -0800)]
perf top: Switch default mode to overwrite mode
perf_top__mmap_read() has a severe performance issue in the Knights
Landing/Mill platform, when monitoring heavy load systems. It costs
several minutes to finish, which is unacceptable.
Currently, 'perf top' uses the non overwrite mode. For non overwrite
mode, it tries to read everything in the ringbuffer and doesn't pause
it. Once there are lots of samples delivered persistently, the
processing time could be very long. Also, the latest samples could be
lost when the ringbuffer is full.
For overwrite mode, it takes a snapshot for the system by pausing the
ringbuffer, which could significantly reduce the processing time. Also,
the overwrite mode always keep the latest samples. Considering the real
time requirement for 'perf top', the overwrite mode is more suitable for
it.
Actually, 'perf top' was overwrite mode. It is changed to non overwrite
mode since commit
93fc64f14472 ("perf top: Switch to non overwrite
mode"). It's better to change it back to overwrite mode by default.
For the kernel which doesn't support overwrite mode, it will fall back
to non overwrite mode.
There would be some records lost in overwrite mode because of pausing
the ringbuffer. It has little impact for the accuracy of the snapshot
and can be tolerated.
For overwrite mode, unconditionally wait 100 ms before each snapshot. It
also reduces the overhead caused by pausing ringbuffer, especially on
light load system.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-17-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:30 +0000 (13:26 -0800)]
perf top: Remove lost events checking
There would be some records lost in overwrite mode because of pausing
the ringbuffer. It has little impact for the accuracy of the snapshot
and could be tolerated by 'perf top'.
Remove the lost events checking.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-16-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:29 +0000 (13:26 -0800)]
perf hists browser: Add parameter to disable lost event warning
For overwrite mode, the ringbuffer will be paused. The event lost is
expected. It needs a way to notify the browser not print the warning.
It will be used later for perf top to disable lost event warning in
overwrite mode. There is no behavior change for now.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-15-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:28 +0000 (13:26 -0800)]
perf top: Add overwrite fall back
Switch to non-overwrite mode if kernel doesnot support overwrite
ringbuffer.
It's only effect when overwrite mode is supported. No change to current
behavior.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-14-git-send-email-kan.liang@intel.com
[ Use perf_missing_features.write_backward instead of the non merged is_write_backward_fail() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Arnaldo Carvalho de Melo [Fri, 2 Feb 2018 14:27:25 +0000 (11:27 -0300)]
perf evsel: Expose the perf_missing_features struct
As tools may need to adjust to missing features, as 'perf top' will, in
the next csets, to cope with a missing 'write_backward' feature.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-jelngl9q1ooaizvkcput9tic@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:26 +0000 (13:26 -0800)]
perf top: Check per-event overwrite term
Per-event overwrite term is not forbidden in 'perf top', which can bring
problems. Because 'perf top' only support non-overwrite mode now.
Add new rules and check regarding to overwrite term for 'perf top'.
- All events either have same per-event term or don't have per-event
mode setting. Otherwise, it will error out.
- Per-event overwrite term should be consistent as opts->overwrite.
If not, updating the opts->overwrite according to per-event term.
Make it possible to support either non-overwrite or overwrite mode.
The overwrite mode is forbidden now, which will be removed when the
overwrite mode is supported later.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-12-git-send-email-kan.liang@intel.com
[ Renamed perf_top_overwrite_check to perf_top__overwrite_check, to follow existing convention ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:25 +0000 (13:26 -0800)]
perf mmap: Discard legacy interface for mmap read
Discards perf_mmap__read_backward() and perf_mmap__read_catchup(). No
tools use them.
There are tools still use perf_mmap__read_forward(). Keep it, but add
comments to point to the new interface for future use.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-11-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:24 +0000 (13:26 -0800)]
perf test: Update mmap read functions for backward-ring-buffer test
Use the new perf_mmap__read_* interfaces for overwrite ringbuffer test.
Commiter notes:
Testing:
[root@seventh ~]# perf test -v backward
48: Read backward ring buffer :
--- start ---
test child forked, pid 8309
Using CPUID GenuineIntel-6-9E
mmap size
1052672B
mmap size 8192B
Finished reading overwrite ring buffer: rewind
test child finished with 0
---- end ----
Read backward ring buffer: Ok
[root@seventh ~]#
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-10-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kan Liang [Thu, 18 Jan 2018 21:26:23 +0000 (13:26 -0800)]
perf mmap: Introduce perf_mmap__read_event()
Except for 'perf record', the other perf tools read events one by one
from the ring buffer using perf_mmap__read_forward(). But it only
supports non-overwrite mode.
Introduce perf_mmap__read_event() to support both non-overwrite and
overwrite mode.
Usage:
perf_mmap__read_init()
while(event = perf_mmap__read_event()) {
//process the event
perf_mmap__consume()
}
perf_mmap__read_done()
It cannot use perf_mmap__read_backward(). Because it always reads the
stale buffer which is already processed. Furthermore, the forward and
backward concepts have been removed. The perf_mmap__read_backward() will
be replaced and discarded later.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1516310792-208685-9-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
projects / platform / kernel / linux-rpi.git / log