Srinivas Neeli [Fri, 9 Apr 2021 14:08:06 +0000 (19:38 +0530)]
gpio: zynq: Check return value of irq_get_irq_data
[ Upstream commit
35d7b72a632bc7afb15356f44005554af8697904 ]
In two different instances the return value of "irq_get_irq_data"
API was neither captured nor checked.
Fixed it by capturing the return value and then checking for any error.
Addresses-Coverity: "returned_null"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Srinivas Neeli [Fri, 9 Apr 2021 14:08:05 +0000 (19:38 +0530)]
gpio: zynq: Check return value of pm_runtime_get_sync
[ Upstream commit
a51b2fb94b04ab71e53a71b9fad03fa826941254 ]
Return value of "pm_runtime_get_sync" API was neither captured nor checked.
Fixed it by capturing the return value and then checking for any warning.
Addresses-Coverity: "check_return"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jaroslav Kysela [Mon, 14 Jun 2021 07:17:46 +0000 (09:17 +0200)]
ASoC: soc-pcm: fix the return value in dpcm_apply_symmetry()
[ Upstream commit
12ffd726824a2f52486f72338b6fd3244b512959 ]
In case, where the loops are not executed for a reason, the uninitialized
variable 'err' is returned to the caller. Make code fully predictible
and assign zero in the declaration.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: Mark Brown <broonie@kernel.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20210614071746.1787072-1-perex@perex.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiyu Yang [Thu, 10 Jun 2021 02:49:20 +0000 (10:49 +0800)]
iommu/arm-smmu: Fix arm_smmu_device refcount leak in address translation
[ Upstream commit
7c8f176d6a3fa18aa0f8875da6f7c672ed2a8554 ]
The reference counting issue happens in several exception handling paths
of arm_smmu_iova_to_phys_hard(). When those error scenarios occur, the
function forgets to decrease the refcount of "smmu" increased by
arm_smmu_rpm_get(), causing a refcount leak.
Fix this issue by jumping to "out" label when those error scenarios
occur.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/1623293391-17261-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Xiyu Yang [Thu, 10 Jun 2021 02:54:29 +0000 (10:54 +0800)]
iommu/arm-smmu: Fix arm_smmu_device refcount leak when arm_smmu_rpm_get fails
[ Upstream commit
1adf30f198c26539a62d761e45af72cde570413d ]
arm_smmu_rpm_get() invokes pm_runtime_get_sync(), which increases the
refcount of the "smmu" even though the return value is less than 0.
The reference counting issue happens in some error handling paths of
arm_smmu_rpm_get() in its caller functions. When arm_smmu_rpm_get()
fails, the caller functions forget to decrease the refcount of "smmu"
increased by arm_smmu_rpm_get(), causing a refcount leak.
Fix this issue by calling pm_runtime_resume_and_get() instead of
pm_runtime_get_sync() in arm_smmu_rpm_get(), which can keep the refcount
balanced in case of failure.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/1623293672-17954-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Geoff Levand [Thu, 3 Jun 2021 19:17:02 +0000 (19:17 +0000)]
powerpc/ps3: Add dma_mask to ps3_dma_region
[ Upstream commit
9733862e50fdba55e7f1554e4286fcc5302ff28e ]
Commit
f959dcd6ddfd29235030e8026471ac1b022ad2b0 (dma-direct: Fix
potential NULL pointer dereference) added a null check on the
dma_mask pointer of the kernel's device structure.
Add a dma_mask variable to the ps3_dma_region structure and set
the device structure's dma_mask pointer to point to this new variable.
Fixes runtime errors like these:
# WARNING: Fixes tag on line 10 doesn't match correct format
# WARNING: Fixes tag on line 10 doesn't match correct format
ps3_system_bus_match:349: dev=8.0(sb_01), drv=8.0(ps3flash): match
WARNING: CPU: 0 PID: 1 at kernel/dma/mapping.c:151 .dma_map_page_attrs+0x34/0x1e0
ps3flash sb_01: ps3stor_setup:193: map DMA region failed
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/562d0c9ea0100a30c3b186bcc7adb34b0bbd2cd7.1622746428.git.geoff@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Iwai [Tue, 8 Jun 2021 14:04:37 +0000 (16:04 +0200)]
ALSA: sb: Fix potential double-free of CSP mixer elements
[ Upstream commit
c305366a37441c2ac90b08711cb6f032b43672f2 ]
snd_sb_qsound_destroy() contains the calls of removing the previously
created mixer controls, but it doesn't clear the pointers. As
snd_sb_qsound_destroy() itself may be repeatedly called via ioctl,
this could lead to double-free potentially.
Fix it by clearing the struct fields properly afterwards.
Link: https://lore.kernel.org/r/20210608140540.17885-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Po-Hsu Lin [Tue, 25 May 2021 02:36:14 +0000 (10:36 +0800)]
selftests: timers: rtcpie: skip test if default RTC device does not exist
[ Upstream commit
0d3e5a057992bdc66e4dca2ca50b77fa4a7bd90e ]
This test will require /dev/rtc0, the default RTC device, or one
specified by user to run. Since this default RTC is not guaranteed to
exist on all of the devices, so check its existence first, otherwise
skip this test with the kselftest skip code 4.
Without this patch this test will fail like this on a s390x zVM:
$ selftests: timers: rtcpie
$ /dev/rtc0: No such file or directory
not ok 1 selftests: timers: rtcpie # exit=22
With this patch:
$ selftests: timers: rtcpie
$ Default RTC /dev/rtc0 does not exist. Test Skipped!
not ok 9 selftests: timers: rtcpie # SKIP
Fixed up change log so "With this patch" text doesn't get dropped.
Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Fabrice Fontaine [Mon, 10 May 2021 05:31:33 +0000 (07:31 +0200)]
s390: disable SSP when needed
[ Upstream commit
42e8d652438f5ddf04e5dac299cb5e623d113dc0 ]
Though -nostdlib is passed in PURGATORY_LDFLAGS and -ffreestanding in
KBUILD_CFLAGS_DECOMPRESSOR, -fno-stack-protector must also be passed to
avoid linking errors related to undefined references to
'__stack_chk_guard' and '__stack_chk_fail' if toolchain enforces
-fstack-protector.
Fixes
- https://gitlab.com/kubu93/buildroot/-/jobs/
1247043361
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Tested-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Link: https://lore.kernel.org/r/20210510053133.1220167-1-fontaine.fabrice@gmail.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Valentin Vidic [Tue, 27 Apr 2021 19:40:10 +0000 (21:40 +0200)]
s390/sclp_vt220: fix console name to match device
[ Upstream commit
b7d91d230a119fdcc334d10c9889ce9c5e15118b ]
Console name reported in /proc/consoles:
ttyS1 -W- (EC p ) 4:65
does not match the char device name:
crw--w---- 1 root root 4, 65 May 17 12:18 /dev/ttysclp0
so debian-installer inside a QEMU s390x instance gets confused and fails
to start with the following error:
steal-ctty: No such file or directory
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Link: https://lore.kernel.org/r/20210427194010.9330-1-vvidic@valentin-vidic.from.hr
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniel Mack [Fri, 28 May 2021 13:33:20 +0000 (15:33 +0200)]
serial: tty: uartlite: fix console setup
[ Upstream commit
d157fca711ad42e75efef3444c83d2e1a17be27a ]
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zou Wei [Thu, 13 May 2021 08:57:29 +0000 (16:57 +0800)]
fsi: Add missing MODULE_DEVICE_TABLE
[ Upstream commit
19a52178125c1e8b84444d85f2ce34c0964b4a91 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620896249-52769-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yufen Yu [Mon, 24 May 2021 09:35:21 +0000 (05:35 -0400)]
ASoC: img: Fix PM reference leak in img_i2s_in_probe()
[ Upstream commit
81aad47278539f02de808bcc8251fed0ad3d6f55 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Link: https://lore.kernel.org/r/20210524093521.612176-1-yuyufen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren [Sat, 22 May 2021 05:10:01 +0000 (08:10 +0300)]
mfd: cpcap: Fix cpcap dmamask not set warnings
[ Upstream commit
0b7cbe811ca524295ea43d9a4d73d3427e419c54 ]
We have started to get a bunch of pointless dmamask not set warnings
that makes the output of dmesg -l err,warn hard to read with many
extra warnings:
cpcap-regulator cpcap-regulator.0: DMA mask not set
cpcap_adc cpcap_adc.0: DMA mask not set
cpcap_battery cpcap_battery.0: DMA mask not set
cpcap-charger cpcap-charger.0: DMA mask not set
cpcap-pwrbutton cpcap-pwrbutton.0: DMA mask not set
cpcap-led cpcap-led.0: DMA mask not set
cpcap-led cpcap-led.1: DMA mask not set
cpcap-led cpcap-led.2: DMA mask not set
cpcap-led cpcap-led.3: DMA mask not set
cpcap-led cpcap-led.4: DMA mask not set
cpcap-rtc cpcap-rtc.0: DMA mask not set
cpcap-usb-phy cpcap-usb-phy.0: DMA mask not set
This seems to have started with commit
4d8bde883bfb ("OF: Don't set
default coherent DMA mask"). We have the parent SPI controller use
DMA, while CPCAP driver and it's children do not. For audio, the
DMA is handled over I2S bus with the McBSP driver.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Ivan Jelincic <parazyd@dyne.org>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zou Wei [Wed, 12 May 2021 06:33:46 +0000 (14:33 +0800)]
mfd: da9052/stmpe: Add and modify MODULE_DEVICE_TABLE
[ Upstream commit
4700ef326556ed74aba188f12396740a8c1c21dd ]
This patch adds/modifies MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Tue, 25 May 2021 18:18:18 +0000 (13:18 -0500)]
scsi: qedi: Fix cleanup session block/unblock use
[ Upstream commit
0c72191da68638a479602dd515b587ada913184a ]
Drivers shouldn't be calling block/unblock session for cmd cleanup because
the functions can change the session state from under libiscsi. This adds
a new a driver level bit so it can block all I/O the host while it drains
the card.
Link: https://lore.kernel.org/r/20210525181821.7617-26-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Tue, 25 May 2021 18:18:17 +0000 (13:18 -0500)]
scsi: qedi: Fix TMF session block/unblock use
[ Upstream commit
2819b4ae2873d50fd55292877b0231ec936c3b2e ]
Drivers shouldn't be calling block/unblock session for tmf handling because
the functions can change the session state from under libiscsi.
iscsi_queuecommand's call to iscsi_prep_scsi_cmd_pdu->
iscsi_check_tmf_restrictions will prevent new cmds from being sent to qedi
after we've started handling a TMF. So we don't need to try and block it in
the driver, and we can remove these block calls.
Link: https://lore.kernel.org/r/20210525181821.7617-25-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Tue, 25 May 2021 18:18:13 +0000 (13:18 -0500)]
scsi: qedi: Fix race during abort timeouts
[ Upstream commit
2ce002366a3fcc3f9616d4583194f65dde0ad253 ]
If the SCSI cmd completes after qedi_tmf_work calls iscsi_itt_to_task then
the qedi qedi_cmd->task_id could be freed and used for another cmd. If we
then call qedi_iscsi_cleanup_task with that task_id we will be cleaning up
the wrong cmd.
Wait to release the task_id until the last put has been done on the
iscsi_task. Because libiscsi grabs a ref to the task when sending the
abort, we know that for the non-abort timeout case that the task_id we are
referencing is for the cmd that was supposed to be aborted.
A latter commit will fix the case where the abort times out while we are
running qedi_tmf_work.
Link: https://lore.kernel.org/r/20210525181821.7617-21-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Tue, 25 May 2021 18:18:12 +0000 (13:18 -0500)]
scsi: qedi: Fix null ref during abort handling
[ Upstream commit
5777b7f0f03ce49372203b6521631f62f2810c8f ]
If qedi_process_cmd_cleanup_resp finds the cmd it frees the work and sets
list_tmf_work to NULL, so qedi_tmf_work should check if list_tmf_work is
non-NULL when it wants to force cleanup.
Link: https://lore.kernel.org/r/20210525181821.7617-20-michael.christie@oracle.com
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Tue, 25 May 2021 18:18:07 +0000 (13:18 -0500)]
scsi: iscsi: Fix shost->max_id use
[ Upstream commit
bdd4aad7ff92ae39c2e93c415bb6761cb8b584da ]
The iscsi offload drivers are setting the shost->max_id to the max number
of sessions they support. The problem is that max_id is not the max number
of targets but the highest identifier the targets can have. To use it to
limit the number of targets we need to set it to max sessions - 1, or we
can end up with a session we might not have preallocated resources for.
Link: https://lore.kernel.org/r/20210525181821.7617-15-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Tue, 25 May 2021 18:18:06 +0000 (13:18 -0500)]
scsi: iscsi: Fix conn use after free during resets
[ Upstream commit
ec29d0ac29be366450a7faffbcf8cba3a6a3b506 ]
If we haven't done a unbind target call we can race where
iscsi_conn_teardown wakes up the EH thread and then frees the conn while
those threads are still accessing the conn ehwait.
We can only do one TMF per session so this just moves the TMF fields from
the conn to the session. We can then rely on the
iscsi_session_teardown->iscsi_remove_session->__iscsi_unbind_session call
to remove the target and it's devices, and know after that point there is
no device or scsi-ml callout trying to access the session.
Link: https://lore.kernel.org/r/20210525181821.7617-14-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mike Christie [Tue, 25 May 2021 18:18:03 +0000 (13:18 -0500)]
scsi: iscsi: Add iscsi_cls_conn refcount helpers
[ Upstream commit
b1d19e8c92cfb0ded180ef3376c20e130414e067 ]
There are a couple places where we could free the iscsi_cls_conn while it's
still in use. This adds some helpers to get/put a refcount on the struct
and converts an exiting user. Subsequent commits will then use the helpers
to fix 2 bugs in the eh code.
Link: https://lore.kernel.org/r/20210525181821.7617-11-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chandrakanth Patil [Fri, 28 May 2021 13:13:06 +0000 (18:43 +0530)]
scsi: megaraid_sas: Handle missing interrupts while re-enabling IRQs
[ Upstream commit
9bedd36e9146b34dda4d6994e3aa1d72bc6442c1 ]
While reenabling the IRQ after IRQ poll there may be a small window for the
firmware to post the replies with interrupts raised. In that case the
driver will not see the interrupts which leads to I/O timeout.
This issue only happens when there are many I/O completions on a single
reply queue. This forces the driver to switch between the interrupt and IRQ
context.
Make the driver process the reply queue one more time after enabling the
IRQ.
Link: https://lore.kernel.org/linux-scsi/20201102072746.27410-1-sreekanth.reddy@broadcom.com/
Link: https://lore.kernel.org/r/20210528131307.25683-5-chandrakanth.patil@broadcom.com
Cc: Tomas Henzl <thenzl@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kashyap Desai [Fri, 28 May 2021 13:13:05 +0000 (18:43 +0530)]
scsi: megaraid_sas: Early detection of VD deletion through RaidMap update
[ Upstream commit
ae6874ba4b43c5a00065f48599811a09d33b873d ]
Consider the case where a VD is deleted and the targetID of that VD is
assigned to a newly created VD. If the sequence of deletion/addition of VD
happens very quickly there is a possibility that second event (VD add)
occurs even before the driver processes the first event (VD delete). As
event processing is done in deferred context the device list remains the
same (but targetID is re-used) so driver will not learn the VD
deletion/additon. I/Os meant for the older VD will be directed to new VD
which may lead to data corruption.
Make driver detect the deleted VD as soon as possible based on the RaidMap
update and block further I/O to that device.
Link: https://lore.kernel.org/r/20210528131307.25683-4-chandrakanth.patil@broadcom.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chandrakanth Patil [Fri, 28 May 2021 13:13:04 +0000 (18:43 +0530)]
scsi: megaraid_sas: Fix resource leak in case of probe failure
[ Upstream commit
b5438f48fdd8e1c3f130d32637511efd32038152 ]
The driver doesn't clean up all the allocated resources properly when
scsi_add_host(), megasas_start_aen() function fails during the PCI device
probe.
Clean up all those resources.
Link: https://lore.kernel.org/r/20210528131307.25683-3-chandrakanth.patil@broadcom.com
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiapeng Chong [Tue, 1 Jun 2021 11:07:10 +0000 (19:07 +0800)]
fs/jfs: Fix missing error code in lmLogInit()
[ Upstream commit
492109333c29e1bb16d8732e1d597b02e8e0bf2e ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'rc.
Eliminate the follow smatch warning:
fs/jfs/jfs_logmgr.c:1327 lmLogInit() warn: missing error code 'rc'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hannes Reinecke [Tue, 27 Apr 2021 08:30:11 +0000 (10:30 +0200)]
scsi: scsi_dh_alua: Check for negative result value
[ Upstream commit
7e26e3ea028740f934477ec01ba586ab033c35aa ]
scsi_execute() will now return a negative error if there was an error prior
to command submission; evaluate that instead if checking for DRIVER_ERROR.
[mkp: build fix]
Link: https://lore.kernel.org/r/20210427083046.31620-6-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hannes Reinecke [Tue, 27 Apr 2021 08:30:09 +0000 (10:30 +0200)]
scsi: core: Fixup calling convention for scsi_mode_sense()
[ Upstream commit
8793613de913e03e7c884f4cc56e350bc716431e ]
The description for scsi_mode_sense() claims to return the number of valid
bytes on success, which is not what the code does. Additionally there is
no gain in returning the SCSI status, as everything the callers do is to
check against scsi_result_is_good(), which is what scsi_mode_sense() does
already. So change the calling convention to return a standard error code
on failure, and 0 on success, and adapt the description and all callers.
Link: https://lore.kernel.org/r/20210427083046.31620-4-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Suganath Prabu S [Tue, 18 May 2021 05:16:23 +0000 (10:46 +0530)]
scsi: mpt3sas: Fix deadlock while cancelling the running firmware event
[ Upstream commit
e2fac6c44ae06e58ac02181b048af31195883c31 ]
Do not cancel current running firmware event work if the event type is
different from MPT3SAS_REMOVE_UNRESPONDING_DEVICES. Otherwise a deadlock
can be observed while cancelling the current firmware event work if a hard
reset operation is called as part of processing the current event.
Link: https://lore.kernel.org/r/20210518051625.1596742-2-suganath-prabu.subramani@broadcom.com
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Christophe JAILLET [Tue, 25 May 2021 19:44:04 +0000 (21:44 +0200)]
tty: serial: 8250: serial_cs: Fix a memory leak in error handling path
[ Upstream commit
fad92b11047a748c996ebd6cfb164a63814eeb2e ]
In the probe function, if the final 'serial_config()' fails, 'info' is
leaking.
Add a resource handling path to free this memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dc25f96b7faebf42e60fe8d02963c941cf4d8124.1621971720.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yufen Yu [Mon, 24 May 2021 09:38:11 +0000 (05:38 -0400)]
ALSA: ac97: fix PM reference leak in ac97_bus_remove()
[ Upstream commit
a38e93302ee25b2ca6f4ee76c6c974cf3637985e ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Link: https://lore.kernel.org/r/20210524093811.612302-1-yuyufen@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
John Garry [Wed, 19 May 2021 14:31:02 +0000 (22:31 +0800)]
scsi: core: Cap scsi_host cmd_per_lun at can_queue
[ Upstream commit
ea2f0f77538c50739b9fb4de4700cee5535e1f77 ]
The sysfs handling function sdev_store_queue_depth() enforces that the sdev
queue depth cannot exceed shost can_queue. The initial sdev queue depth
comes from shost cmd_per_lun. However, the LLDD may manually set
cmd_per_lun to be larger than can_queue, which leads to an initial sdev
queue depth greater than can_queue.
Such an issue was reported in [0], which caused a hang. That has since been
fixed in commit
fc09acb7de31 ("scsi: scsi_debug: Fix cmd_per_lun, set to
max_queue").
Stop this possibly happening for other drivers by capping shost cmd_per_lun
at shost can_queue.
[0] https://lore.kernel.org/linux-scsi/YHaez6iN2HHYxYOh@T590/
Link: https://lore.kernel.org/r/1621434662-173079-1-git-send-email-john.garry@huawei.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 14 May 2021 19:55:56 +0000 (12:55 -0700)]
scsi: lpfc: Fix crash when lpfc_sli4_hba_setup() fails to initialize the SGLs
[ Upstream commit
5aa615d195f1e142c662cb2253f057c9baec7531 ]
The driver is encountering a crash in lpfc_free_iocb_list() while
performing initial attachment.
Code review found this to be an errant failure path that was taken, jumping
to a tag that then referenced structures that were uninitialized.
Fix the failure path.
Link: https://lore.kernel.org/r/20210514195559.119853-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
James Smart [Fri, 14 May 2021 19:55:51 +0000 (12:55 -0700)]
scsi: lpfc: Fix "Unexpected timeout" error in direct attach topology
[ Upstream commit
e30d55137edef47434c40d7570276a0846fe922c ]
An 'unexpected timeout' message may be seen in a point-2-point topology.
The message occurs when a PLOGI is received before the driver is notified
of FLOGI completion. The FLOGI completion failure causes discovery to be
triggered for a second time. The discovery timer is restarted but no new
discovery activity is initiated, thus the timeout message eventually
appears.
In point-2-point, when discovery has progressed before the FLOGI completion
is processed, it is not a failure. Add code to FLOGI completion to detect
that discovery has progressed and exit the FLOGI handling (noop'ing it).
Link: https://lore.kernel.org/r/20210514195559.119853-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sergey Shtylyov [Wed, 19 May 2021 19:20:15 +0000 (22:20 +0300)]
scsi: hisi_sas: Propagate errors in interrupt_init_v1_hw()
[ Upstream commit
ab17122e758ef68fb21033e25c041144067975f5 ]
After commit
6c11dc060427 ("scsi: hisi_sas: Fix IRQ checks") we have the
error codes returned by platform_get_irq() ready for the propagation
upsream in interrupt_init_v1_hw() -- that will fix still broken deferred
probing. Let's propagate the error codes from devm_request_irq() as well
since I don't see the reason to override them with -ENOENT...
Link: https://lore.kernel.org/r/49ba93a3-d427-7542-d85a-b74fe1a33a73@omp.ru
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ching Huang [Thu, 20 May 2021 06:55:15 +0000 (14:55 +0800)]
scsi: arcmsr: Fix doorbell status being updated late on ARC-1886
[ Upstream commit
d9a231226f28261a787535e08d0c78669e1ad010 ]
It is possible for the IOP to be delayed in updating the doorbell
status. The doorbell status should not be 0 so loop until the value
changes.
Link: https://lore.kernel.org/r/afdfdf7eabecf14632492c4987a6b9ac6312a7ad.camel@areca.com.tw
Signed-off-by: ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Luiz Sampaio [Wed, 19 May 2021 22:30:44 +0000 (19:30 -0300)]
w1: ds2438: fixing bug that would always get page0
[ Upstream commit
1f5e7518f063728aee0679c5086b92d8ea429e11 ]
The purpose of the w1_ds2438_get_page function is to get the register
values at the page passed as the pageno parameter. However, the page0 was
hardcoded, such that the function always returned the page0 contents. Fixed
so that the function can retrieve any page.
Signed-off-by: Luiz Sampaio <sampaio.ime@gmail.com>
Link: https://lore.kernel.org/r/20210519223046.13798-5-sampaio.ime@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Chunfeng Yun [Wed, 19 May 2021 06:39:44 +0000 (14:39 +0800)]
usb: common: usb-conn-gpio: fix NULL pointer dereference of charger
[ Upstream commit
880287910b1892ed2cb38977893b947382a09d21 ]
When power on system with OTG cable, IDDIG's interrupt arises before
the charger registration, it will cause a NULL pointer dereference,
fix the issue by registering the power supply before requesting
IDDIG/VBUS irq.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1621406386-18838-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Sakamoto [Tue, 18 May 2021 08:45:47 +0000 (17:45 +0900)]
Revert "ALSA: bebob/oxfw: fix Kconfig entry for Mackie d.2 Pro"
[ Upstream commit
5d6fb80a142b5994355ce675c517baba6089d199 ]
This reverts commit
0edabdfe89581669609eaac5f6a8d0ae6fe95e7f.
I've explained that optional FireWire card for d.2 is also built-in to
d.2 Pro, however it's wrong. The optional card uses DM1000 ASIC and has
'Mackie DJ Mixer' in its model name of configuration ROM. On the other
hand, built-in FireWire card for d.2 Pro and d.4 Pro uses OXFW971 ASIC
and has 'd.Pro' in its model name according to manuals and user
experiences. The former card is not the card for d.2 Pro. They are similar
in appearance but different internally.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210518084557.102681-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Iwai [Mon, 17 May 2021 13:15:43 +0000 (15:15 +0200)]
ALSA: usx2y: Don't call free_pages_exact() with NULL address
[ Upstream commit
cae0cf651adccee2c3f376e78f30fbd788d0829f ]
Unlike some other functions, we can't pass NULL pointer to
free_pages_exact(). Add a proper NULL check for avoiding possible
Oops.
Link: https://lore.kernel.org/r/20210517131545.27252-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Takashi Iwai [Mon, 17 May 2021 13:15:35 +0000 (15:15 +0200)]
ALSA: usx2y: Avoid camelCase
[ Upstream commit
bae3ce4942980d5f7b2b9855f4a2db0c00f9dfbd ]
For improving readability, convert camelCase fields, variables and
functions to the plain names with underscore. Also align the macros
to be capital letters.
All done via sed, no functional changes.
Note that you'll still see many coding style issues even after this
patch; the fixes will follow.
Link: https://lore.kernel.org/r/20210517131545.27252-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jonathan Cameron [Sun, 9 May 2021 11:33:37 +0000 (12:33 +0100)]
iio: magn: bmc150: Balance runtime pm + use pm_runtime_resume_and_get()
[ Upstream commit
264da512431495e542fcaf56ffe75e7df0e7db74 ]
probe() error paths after runtime pm is enabled, should disable it.
remove() should not call pm_runtime_put_noidle() as there is no
matching get() to have raised the reference count. This case
has no affect a the runtime pm core protects against going negative.
Whilst here use pm_runtime_resume_and_get() to tidy things up a little.
coccicheck script didn't get this one due to complex code structure so
found by inspection.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210509113354.660190-12-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jonathan Cameron [Sun, 9 May 2021 11:33:27 +0000 (12:33 +0100)]
iio: gyro: fxa21002c: Balance runtime pm + use pm_runtime_resume_and_get().
[ Upstream commit
41120ebbb1eb5e9dec93320e259d5b2c93226073 ]
In both the probe() error path and remove() pm_runtime_put_noidle()
is called which will decrement the runtime pm reference count.
However, there is no matching function to have raised the reference count.
Not this isn't a fix as the runtime pm core will stop the reference count
going negative anyway.
An alternative would have been to raise the count in these paths, but
it is not clear why that would be necessary.
Whilst we are here replace some boilerplate with pm_runtime_resume_and_get()
Found using coccicheck script under review at:
https://lore.kernel.org/lkml/
20210427141946.2478411-1-Julia.Lawall@inria.fr/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210509113354.660190-2-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Arnd Bergmann [Fri, 7 May 2021 22:07:53 +0000 (00:07 +0200)]
partitions: msdos: fix one-byte get_unaligned()
[ Upstream commit
1b1774998b2dec837a57d729d1a22e5eb2d6d206 ]
A simplification of get_unaligned() clashes with callers that pass
in a character pointer, causing a harmless warning like:
block/partitions/msdos.c: In function 'msdos_partition':
include/asm-generic/unaligned.h:13:22: warning: 'packed' attribute ignored for field of type 'u8' {aka 'unsigned char'} [-Wattributes]
Remove the SYS_IND() macro with the get_unaligned() call
and just use the ->ind field directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zou Wei [Wed, 12 May 2021 03:54:07 +0000 (11:54 +0800)]
ASoC: intel/boards: add missing MODULE_DEVICE_TABLE
[ Upstream commit
a75e5cdf4dd1307bb1541edbb0c008f40896644c ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620791647-16024-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tong Zhang [Thu, 13 May 2021 04:07:33 +0000 (00:07 -0400)]
misc: alcor_pci: fix null-ptr-deref when there is no PCI bridge
[ Upstream commit
3ce3e45cc333da707d4d6eb433574b990bcc26f5 ]
There is an issue with the ASPM(optional) capability checking function.
A device might be attached to root complex directly, in this case,
bus->self(bridge) will be NULL, thus priv->parent_pdev is NULL.
Since alcor_pci_init_check_aspm(priv->parent_pdev) checks the PCI link's
ASPM capability and populate parent_cap_off, which will be used later by
alcor_pci_aspm_ctrl() to dynamically turn on/off device, what we can do
here is to avoid checking the capability if we are on the root complex.
This will make pdev_cap_off 0 and alcor_pci_aspm_ctrl() will simply
return when bring called, effectively disable ASPM for the device.
[ 1.246492] BUG: kernel NULL pointer dereference, address:
00000000000000c0
[ 1.248731] RIP: 0010:pci_read_config_byte+0x5/0x40
[ 1.253998] Call Trace:
[ 1.254131] ? alcor_pci_find_cap_offset.isra.0+0x3a/0x100 [alcor_pci]
[ 1.254476] alcor_pci_probe+0x169/0x2d5 [alcor_pci]
Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210513040732.1310159-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lv Yunlong [Mon, 26 Apr 2021 17:06:20 +0000 (10:06 -0700)]
misc/libmasm/module: Fix two use after free in ibmasm_init_one
[ Upstream commit
7272b591c4cb9327c43443f67b8fbae7657dd9ae ]
In ibmasm_init_one, it calls ibmasm_init_remote_input_dev().
Inside ibmasm_init_remote_input_dev, mouse_dev and keybd_dev are
allocated by input_allocate_device(), and assigned to
sp->remote.mouse_dev and sp->remote.keybd_dev respectively.
In the err_free_devices error branch of ibmasm_init_one,
mouse_dev and keybd_dev are freed by input_free_device(), and return
error. Then the execution runs into error_send_message error branch
of ibmasm_init_one, where ibmasm_free_remote_input_dev(sp) is called
to unregister the freed sp->remote.mouse_dev and sp->remote.keybd_dev.
My patch add a "error_init_remote" label to handle the error of
ibmasm_init_remote_input_dev(), to avoid the uaf bugs.
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Link: https://lore.kernel.org/r/20210426170620.10546-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michael Walle [Wed, 12 May 2021 14:12:55 +0000 (16:12 +0200)]
serial: fsl_lpuart: disable DMA for console and fix sysrq
[ Upstream commit
8cac2f6eb8548245e6f8fb893fc7f2a714952654 ]
SYSRQ doesn't work with DMA. This is because there is no error
indication whether a symbol had a framing error or not. Actually,
this is not completely correct, there is a bit in the data register
which is set in this case, but we'd have to read change the DMA access
to 16 bit and we'd need to post process the data, thus make the DMA
pointless in the first place.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-10-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sherry Sun [Tue, 27 Apr 2021 02:12:26 +0000 (10:12 +0800)]
tty: serial: fsl_lpuart: fix the potential risk of division or modulo by zero
[ Upstream commit
fcb10ee27fb91b25b68d7745db9817ecea9f1038 ]
We should be very careful about the register values that will be used
for division or modulo operations, althrough the possibility that the
UARTBAUD register value is zero is very low, but we had better to deal
with the "bad data" of hardware in advance to avoid division or modulo
by zero leading to undefined kernel behavior.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210427021226.27468-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Paul E. McKenney [Mon, 5 Apr 2021 16:51:05 +0000 (09:51 -0700)]
rcu: Reject RCU_LOCKDEP_WARN() false positives
[ Upstream commit
3066820034b5dd4e89bd74a7739c51c2d6f5e554 ]
If another lockdep report runs concurrently with an RCU lockdep report
from RCU_LOCKDEP_WARN(), the following sequence of events can occur:
1. debug_lockdep_rcu_enabled() sees that lockdep is enabled
when called from (say) synchronize_rcu().
2. Lockdep is disabled by a concurrent lockdep report.
3. debug_lockdep_rcu_enabled() evaluates its lockdep-expression
argument, for example, lock_is_held(&rcu_bh_lock_map).
4. Because lockdep is now disabled, lock_is_held() plays it safe and
returns the constant 1.
5. But in this case, the constant 1 is not safe, because invoking
synchronize_rcu() under rcu_read_lock_bh() is disallowed.
6. debug_lockdep_rcu_enabled() wrongly invokes lockdep_rcu_suspicious(),
resulting in a false-positive splat.
This commit therefore changes RCU_LOCKDEP_WARN() to check
debug_lockdep_rcu_enabled() after checking the lockdep expression,
so that any "safe" returns from lock_is_held() are rejected by
debug_lockdep_rcu_enabled(). This requires memory ordering, which is
supplied by READ_ONCE(debug_locks). The resulting volatile accesses
prevent the compiler from reordering and the fact that only one variable
is being accessed prevents the underlying hardware from reordering.
The combination works for IA64, which can reorder reads to the same
location, but this is defeated by the volatile accesses, which compile
to load instructions that provide ordering.
Reported-by: syzbot+dde0cc33951735441301@syzkaller.appspotmail.com
Reported-by: Matthew Wilcox <willy@infradead.org>
Reported-by: syzbot+88e4f02896967fe1ab0d@syzkaller.appspotmail.com
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Frederic Weisbecker [Sat, 17 Apr 2021 13:16:49 +0000 (15:16 +0200)]
srcu: Fix broken node geometry after early ssp init
[ Upstream commit
b5befe842e6612cf894cf4a199924ee872d8b7d8 ]
An srcu_struct structure that is initialized before rcu_init_geometry()
will have its srcu_node hierarchy based on CONFIG_NR_CPUS. Once
rcu_init_geometry() is called, this hierarchy is compressed as needed
for the actual maximum number of CPUs for this system.
Later on, that srcu_struct structure is confused, sometimes referring
to its initial CONFIG_NR_CPUS-based hierarchy, and sometimes instead
to the new num_possible_cpus() hierarchy. For example, each of its
->mynode fields continues to reference the original leaf rcu_node
structures, some of which might no longer exist. On the other hand,
srcu_for_each_node_breadth_first() traverses to the new node hierarchy.
There are at least two bad possible outcomes to this:
1) a) A callback enqueued early on an srcu_data structure (call it
*sdp) is recorded pending on sdp->mynode->srcu_data_have_cbs in
srcu_funnel_gp_start() with sdp->mynode pointing to a deep leaf
(say 3 levels).
b) The grace period ends after rcu_init_geometry() shrinks the
nodes level to a single one. srcu_gp_end() walks through the new
srcu_node hierarchy without ever reaching the old leaves so the
callback is never executed.
This is easily reproduced on an 8 CPUs machine with CONFIG_NR_CPUS >= 32
and "rcupdate.rcu_self_test=1". The srcu_barrier() after early tests
verification never completes and the boot hangs:
[ 5413.141029] INFO: task swapper/0:1 blocked for more than 4915 seconds.
[ 5413.147564] Not tainted 5.12.0-rc4+ #28
[ 5413.151927] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 5413.159753] task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00004000
[ 5413.168099] Call Trace:
[ 5413.170555] __schedule+0x36c/0x930
[ 5413.174057] ? wait_for_completion+0x88/0x110
[ 5413.178423] schedule+0x46/0xf0
[ 5413.181575] schedule_timeout+0x284/0x380
[ 5413.185591] ? wait_for_completion+0x88/0x110
[ 5413.189957] ? mark_held_locks+0x61/0x80
[ 5413.193882] ? mark_held_locks+0x61/0x80
[ 5413.197809] ? _raw_spin_unlock_irq+0x24/0x50
[ 5413.202173] ? wait_for_completion+0x88/0x110
[ 5413.206535] wait_for_completion+0xb4/0x110
[ 5413.210724] ? srcu_torture_stats_print+0x110/0x110
[ 5413.215610] srcu_barrier+0x187/0x200
[ 5413.219277] ? rcu_tasks_verify_self_tests+0x50/0x50
[ 5413.224244] ? rdinit_setup+0x2b/0x2b
[ 5413.227907] rcu_verify_early_boot_tests+0x2d/0x40
[ 5413.232700] do_one_initcall+0x63/0x310
[ 5413.236541] ? rdinit_setup+0x2b/0x2b
[ 5413.240207] ? rcu_read_lock_sched_held+0x52/0x80
[ 5413.244912] kernel_init_freeable+0x253/0x28f
[ 5413.249273] ? rest_init+0x250/0x250
[ 5413.252846] kernel_init+0xa/0x110
[ 5413.256257] ret_from_fork+0x22/0x30
2) An srcu_struct structure that is initialized before rcu_init_geometry()
and used afterward will always have stale rdp->mynode references,
resulting in callbacks to be missed in srcu_gp_end(), just like in
the previous scenario.
This commit therefore causes init_srcu_struct_nodes to initialize the
geometry, if needed. This ensures that the srcu_node hierarchy is
properly built and distributed from the get-go.
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Neeraj Upadhyay <neeraju@codeaurora.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Uladzislau Rezki <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
ching Huang [Fri, 16 Apr 2021 03:44:57 +0000 (11:44 +0800)]
scsi: arcmsr: Fix the wrong CDB payload report to IOP
[ Upstream commit
5b8644968d2ca85abb785e83efec36934974b0c2 ]
This patch fixes the wrong CDB payload report to IOP.
Link: https://lore.kernel.org/r/d2c97df3c817595c6faf582839316209022f70da.camel@areca.com.tw
Signed-off-by: ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Robin Gong [Mon, 26 Apr 2021 08:59:09 +0000 (16:59 +0800)]
dmaengine: fsl-qdma: check dma_set_mask return value
[ Upstream commit
f0c07993af0acf5545d5c1445798846565f4f147 ]
For fix below warning reported by static code analysis tool like Coverity
from Synopsys:
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Addresses-Coverity-ID:
12285639 ("Unchecked return value")
Link: https://lore.kernel.org/r/1619427549-20498-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pierre-Louis Bossart [Wed, 5 May 2021 16:36:56 +0000 (11:36 -0500)]
ASoC: Intel: sof_sdw: add mutual exclusion between PCH DMIC and RT715
[ Upstream commit
35564e2bf94611c3eb51d35362addb3cb394ad54 ]
When external RT714/715 devices are used for capture, we don't want
the PCH DMICs to be used.
Any information provided by the SOF platform driver or DMI quirks will
be overridden.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Yingliang [Tue, 6 Apr 2021 13:11:59 +0000 (21:11 +0800)]
leds: tlc591xx: fix return value check in tlc591xx_probe()
[ Upstream commit
ee522bcf026ec82ada793979c3a906274430595a ]
After device_get_match_data(), tlc591xx is not checked, add
check for it and also check np after dev_of_node.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikolay Aleksandrov [Sun, 11 Jul 2021 09:56:29 +0000 (12:56 +0300)]
net: bridge: multicast: fix MRD advertisement router port marking race
commit
000b7287b67555fee39d39fff75229dedde0dcbf upstream.
When an MRD advertisement is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port to the router port list. The multicast lock
protects that list, but it is not acquired in the MRD advertisement case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org
Cc: linus.luessing@c0d3.blue
Fixes:
4b3087c7e37f ("bridge: Snoop Multicast Router Advertisements")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolay Aleksandrov [Sun, 11 Jul 2021 09:56:28 +0000 (12:56 +0300)]
net: bridge: multicast: fix PIM hello router port marking race
commit
04bef83a3358946bfc98a5ecebd1b0003d83d882 upstream.
When a PIM hello packet is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port the router port list. The multicast lock
protects that list, but it is not acquired in the PIM message case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org
Fixes:
91b02d3d133b ("bridge: mcast: add router port on PIM hello message")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 19 Jul 2021 13:01:49 +0000 (15:01 +0200)]
Revert "drm/ast: Remove reference to struct drm_device.pdev"
This reverts commit
fcb041ca5c7787b096aafc899e45f93583e66cbd which is
commit
0ecb51824e838372e01330752503ddf9c0430ef7 upstream.
Turns out this was incomplete, as it is missing a dependancy, so drop it
from the tree.
Link: https://lore.kernel.org/r/CAJn8CcHHKSo7GF29Z1ufXJJpMUzn6+fdvwiqe9=JvgpcfvnbHQ@mail.gmail.com
Reported-by: Xiaotian Feng <xtfeng@gmail.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Michael J. Ruhl <michael.j.ruhl@intel.com>
Cc: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Cc: kernel test robot <lkp@intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Cercueil [Mon, 29 Mar 2021 17:50:45 +0000 (18:50 +0100)]
drm/ingenic: Switch IPU plane to type OVERLAY
commit
68b433fe6937cfa3f8975d18643d5956254edd6a upstream.
It should have been an OVERLAY from the beginning. The documentation
stipulates that there should be an unique PRIMARY plane per CRTC.
Fixes:
fc1acf317b01 ("drm/ingenic: Add support for the IPU")
Cc: <stable@vger.kernel.org> # 5.8+
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20210329175046.214629-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Cercueil [Sun, 24 Jan 2021 08:55:52 +0000 (08:55 +0000)]
drm/ingenic: Fix non-OSD mode
commit
7b4957684e5d813fcbdc98144e3cc5c4467b3e2e upstream.
Even though the JZ4740 did not have the OSD mode, it had (according to
the documentation) two DMA channels, but there is absolutely no
information about how to select the second DMA channel.
Make the ingenic-drm driver work in non-OSD mode by using the
foreground0 plane (which is bound to the DMA0 channel) as the primary
plane, instead of the foreground1 plane, which is the primary plane
when in OSD mode.
Fixes:
3c9bea4ef32b ("drm/ingenic: Add support for OSD mode")
Cc: <stable@vger.kernel.org> # v5.8+
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210124085552.29146-5-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
José Roberto de Souza [Wed, 16 Jun 2021 19:44:15 +0000 (12:44 -0700)]
drm/dp_mst: Add missing drm parameters to recently added call to drm_dbg_kms()
commit
24ff3dc18b99c4b912ab1746e803ddb3be5ced4c upstream.
Commit
3769e4c0af5b ("drm/dp_mst: Avoid to mess up payload table by
ports in stale topology") added to calls to drm_dbg_kms() but it
missed the first parameter, the drm device breaking the build.
Fixes:
3769e4c0af5b ("drm/dp_mst: Avoid to mess up payload table by ports in stale topology")
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210616194415.36926-1-jose.souza@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wayne Lin [Wed, 16 Jun 2021 03:55:01 +0000 (11:55 +0800)]
drm/dp_mst: Avoid to mess up payload table by ports in stale topology
commit
3769e4c0af5b82c8ea21d037013cb9564dfaa51f upstream.
[Why]
After unplug/hotplug hub from the system, userspace might start to
clear stale payloads gradually. If we call drm_dp_mst_deallocate_vcpi()
to release stale VCPI of those ports which are not relating to current
topology, we have chane to wrongly clear active payload table entry for
current topology.
E.g.
We have allocated VCPI 1 in current payload table and we call
drm_dp_mst_deallocate_vcpi() to clean VCPI 1 in stale topology. In
drm_dp_mst_deallocate_vcpi(), it will call drm_dp_mst_put_payload_id()
tp put VCPI 1 and which means ID 1 is available again. Thereafter, if we
want to allocate a new payload stream, it will find ID 1 is available by
drm_dp_mst_assign_payload_id(). However, ID 1 is being used
[How]
Check target sink is relating to current topology or not before doing
any payload table update.
Searching upward to find the target sink's relevant root branch device.
If the found root branch device is not the same root of current
topology, don't update payload table.
Changes since v1:
* Change debug macro to use drm_dbg_kms() instead
* Amend the commit message to add Cc tag.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210616035501.3776-3-Wayne.Lin@amd.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wayne Lin [Wed, 16 Jun 2021 03:55:00 +0000 (11:55 +0800)]
drm/dp_mst: Do not set proposed vcpi directly
commit
35d3e8cb35e75450f87f87e3d314e2d418b6954b upstream.
[Why]
When we receive CSN message to notify one port is disconnected, we will
implicitly set its corresponding num_slots to 0. Later on, we will
eventually call drm_dp_update_payload_part1() to arrange down streams.
In drm_dp_update_payload_part1(), we iterate over all proposed_vcpis[]
to do the update. Not specific to a target sink only. For example, if we
light up 2 monitors, Monitor_A and Monitor_B, and then we unplug
Monitor_B. Later on, when we call drm_dp_update_payload_part1() to try
to update payload for Monitor_A, we'll also implicitly clean payload for
Monitor_B at the same time. And finally, when we try to call
drm_dp_update_payload_part1() to clean payload for Monitor_B, we will do
nothing at this time since payload for Monitor_B has been cleaned up
previously.
For StarTech 1to3 DP hub, it seems like if we didn't update DPCD payload
ID table then polling for "ACT Handled"(BIT_1 of DPCD 002C0h) will fail
and this polling will last for 3 seconds.
Therefore, guess the best way is we don't set the proposed_vcpi[]
diretly. Let user of these herlper functions to set the proposed_vcpi
directly.
[How]
1. Revert commit
7617e9621bf2 ("drm/dp_mst: clear time slots for ports
invalid")
2. Tackle the issue in previous commit by skipping those trasient
proposed VCPIs. These stale VCPIs shoulde be explicitly cleared by
user later on.
Changes since v1:
* Change debug macro to use drm_dbg_kms() instead
* Amend the commit message to add Fixed & Cc tags
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Fixes:
7617e9621bf2 ("drm/dp_mst: clear time slots for ports invalid")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210616035501.3776-2-Wayne.Lin@amd.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhen Lei [Mon, 12 Jul 2021 08:55:44 +0000 (16:55 +0800)]
fbmem: Do not delete the mode that is still in use
commit
0af778269a522c988ef0b4188556aba97fb420cc upstream.
The execution of fb_delete_videomode() is not based on the result of the
previous fbcon_mode_deleted(). As a result, the mode is directly deleted,
regardless of whether it is still in use, which may cause UAF.
==================================================================
BUG: KASAN: use-after-free in fb_mode_is_equal+0x36e/0x5e0 \
drivers/video/fbdev/core/modedb.c:924
Read of size 4 at addr
ffff88807e0ddb1c by task syz-executor.0/18962
CPU: 2 PID: 18962 Comm: syz-executor.0 Not tainted 5.10.45-rc1+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ...
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x137/0x1be lib/dump_stack.c:118
print_address_description+0x6c/0x640 mm/kasan/report.c:385
__kasan_report mm/kasan/report.c:545 [inline]
kasan_report+0x13d/0x1e0 mm/kasan/report.c:562
fb_mode_is_equal+0x36e/0x5e0 drivers/video/fbdev/core/modedb.c:924
fbcon_mode_deleted+0x16a/0x220 drivers/video/fbdev/core/fbcon.c:2746
fb_set_var+0x1e1/0xdb0 drivers/video/fbdev/core/fbmem.c:975
do_fb_ioctl+0x4d9/0x6e0 drivers/video/fbdev/core/fbmem.c:1108
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl+0xfb/0x170 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 18960:
kasan_save_stack mm/kasan/common.c:48 [inline]
kasan_set_track+0x3d/0x70 mm/kasan/common.c:56
kasan_set_free_info+0x17/0x30 mm/kasan/generic.c:355
__kasan_slab_free+0x108/0x140 mm/kasan/common.c:422
slab_free_hook mm/slub.c:1541 [inline]
slab_free_freelist_hook+0xd6/0x1a0 mm/slub.c:1574
slab_free mm/slub.c:3139 [inline]
kfree+0xca/0x3d0 mm/slub.c:4121
fb_delete_videomode+0x56a/0x820 drivers/video/fbdev/core/modedb.c:1104
fb_set_var+0x1f3/0xdb0 drivers/video/fbdev/core/fbmem.c:978
do_fb_ioctl+0x4d9/0x6e0 drivers/video/fbdev/core/fbmem.c:1108
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl+0xfb/0x170 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
13ff178ccd6d ("fbcon: Call fbcon_mode_deleted/new_modelist directly")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Cc: <stable@vger.kernel.org> # v5.3+
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712085544.2828-1-thunder.leizhen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Brauner [Wed, 14 Jul 2021 13:47:49 +0000 (15:47 +0200)]
cgroup: verify that source is a string
commit
3b0462726e7ef281c35a7a4ae33e93ee2bc9975b upstream.
The following sequence can be used to trigger a UAF:
int fscontext_fd = fsopen("cgroup");
int fd_null = open("/dev/null, O_RDONLY);
int fsconfig(fscontext_fd, FSCONFIG_SET_FD, "source", fd_null);
close_range(3, ~0U, 0);
The cgroup v1 specific fs parser expects a string for the "source"
parameter. However, it is perfectly legitimate to e.g. specify a file
descriptor for the "source" parameter. The fs parser doesn't know what
a filesystem allows there. So it's a bug to assume that "source" is
always of type fs_value_is_string when it can reasonably also be
fs_value_is_file.
This assumption in the cgroup code causes a UAF because struct
fs_parameter uses a union for the actual value. Access to that union is
guarded by the param->type member. Since the cgroup paramter parser
didn't check param->type but unconditionally moved param->string into
fc->source a close on the fscontext_fd would trigger a UAF during
put_fs_context() which frees fc->source thereby freeing the file stashed
in param->file causing a UAF during a close of the fd_null.
Fix this by verifying that param->type is actually a string and report
an error if not.
In follow up patches I'll add a new generic helper that can be used here
and by other filesystems instead of this error-prone copy-pasta fix.
But fixing it in here first makes backporting a it to stable a lot
easier.
Fixes:
8d2451f4994f ("cgroup1: switch to option-by-option parsing")
Reported-by: syzbot+283ce5a46486d6acdbaf@syzkaller.appspotmail.com
Cc: Christoph Hellwig <hch@lst.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@kernel.org>
Cc: syzkaller-bugs <syzkaller-bugs@googlegroups.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Wed, 30 Jun 2021 16:44:13 +0000 (19:44 +0300)]
drm/i915/gt: Fix -EDEADLK handling regression
commit
2feeb52859fc1ab94cd35b61ada3a6ac4ff24243 upstream.
The conversion to ww mutexes failed to address the fence code which
already returns -EDEADLK when we run out of fences. Ww mutexes on
the other hand treat -EDEADLK as an internal errno value indicating
a need to restart the operation due to a deadlock. So now when the
fence code returns -EDEADLK the higher level code erroneously
restarts everything instead of returning the error to userspace
as is expected.
To remedy this let's switch the fence code to use a different errno
value for this. -ENOBUFS seems like a semi-reasonable unique choice.
Apart from igt the only user of this I could find is sna, and even
there all we do is dump the current fence registers from debugfs
into the X server log. So no user visible functionality is affected.
If we really cared about preserving this we could of course convert
back to -EDEADLK higher up, but doesn't seem like that's worth
the hassle here.
Not quite sure which commit specifically broke this, but I'll
just attribute it to the general gem ww mutex work.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Hellström <thomas.hellstrom@intel.com>
Testcase: igt/gem_pread/exhaustion
Testcase: igt/gem_pwrite/basic-exhaustion
Testcase: igt/gem_fenced_exec_thrash/too-many-fences
Fixes:
80f0b679d6f0 ("drm/i915: Add an implementation for i915_gem_ww_ctx locking, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210630164413.25481-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
(cherry picked from commit
78d2ad7eb4e1f0e9cd5d79788446b6092c21d3e0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthew Auld [Tue, 13 Jul 2021 13:04:31 +0000 (14:04 +0100)]
drm/i915/gtt: drop the page table optimisation
commit
0abb33bfca0fb74df76aac03e90ce685016ef7be upstream.
We skip filling out the pt with scratch entries if the va range covers
the entire pt, since we later have to fill it with the PTEs for the
object pages anyway. However this might leave open a small window where
the PTEs don't point to anything valid for the HW to consume.
When for example using 2M GTT pages this fill_px() showed up as being
quite significant in perf measurements, and ends up being completely
wasted since we ignore the pt and just use the pde directly.
Anyway, currently we have our PTE construction split between alloc and
insert, which is probably slightly iffy nowadays, since the alloc
doesn't actually allocate anything anymore, instead it just sets up the
page directories and points the PTEs at the scratch page. Later when we
do the insert step we re-program the PTEs again. Better might be to
squash the alloc and insert into a single step, then bringing back this
optimisation(along with some others) should be possible.
Fixes:
14826673247e ("drm/i915: Only initialize partially filled pagetables")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210713130431.2392740-1-matthew.auld@intel.com
(cherry picked from commit
8f88ca76b3942d82e2c1cea8735ec368d89ecc15)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt (VMware) [Thu, 15 Jul 2021 04:02:06 +0000 (00:02 -0400)]
tracing: Do not reference char * as a string in histograms
commit
704adfb5a9978462cd861f170201ae2b5e3d3a80 upstream.
The histogram logic was allowing events with char * pointers to be used as
normal strings. But it was easy to crash the kernel with:
# echo 'hist:keys=filename' > events/syscalls/sys_enter_openat/trigger
And open some files, and boom!
BUG: unable to handle page fault for address:
00007f2ced0c3280
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD
1173fa067 P4D
1173fa067 PUD
1171b6067 PMD
1171dd067 PTE 0
Oops: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 1810 Comm: cat Not tainted 5.13.0-rc5-test+ #61
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01
v03.03 07/14/2016
RIP: 0010:strlen+0x0/0x20
Code: f6 82 80 2a 0b a9 20 74 11 0f b6 50 01 48 83 c0 01 f6 82 80 2a 0b
a9 20 75 ef c3 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 <80> 3f 00 74
10 48 89 f8 48 83 c0 01 80 38 00 75 f7 48 29 f8 c3
RSP: 0018:
ffffbdbf81567b50 EFLAGS:
00010246
RAX:
0000000000000003 RBX:
ffff93815cdb3800 RCX:
ffff9382401a22d0
RDX:
0000000000000100 RSI:
0000000000000000 RDI:
00007f2ced0c3280
RBP:
0000000000000100 R08:
ffff9382409ff074 R09:
ffffbdbf81567c98
R10:
ffff9382409ff074 R11:
0000000000000000 R12:
ffff9382409ff074
R13:
0000000000000001 R14:
ffff93815a744f00 R15:
00007f2ced0c3280
FS:
00007f2ced0f8580(0000) GS:
ffff93825a800000(0000)
knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f2ced0c3280 CR3:
0000000107069005 CR4:
00000000001706e0
Call Trace:
event_hist_trigger+0x463/0x5f0
? find_held_lock+0x32/0x90
? sched_clock_cpu+0xe/0xd0
? lock_release+0x155/0x440
? kernel_init_free_pages+0x6d/0x90
? preempt_count_sub+0x9b/0xd0
? kernel_init_free_pages+0x6d/0x90
? get_page_from_freelist+0x12c4/0x1680
? __rb_reserve_next+0xe5/0x460
? ring_buffer_lock_reserve+0x12a/0x3f0
event_triggers_call+0x52/0xe0
ftrace_syscall_enter+0x264/0x2c0
syscall_trace_enter.constprop.0+0x1ee/0x210
do_syscall_64+0x1c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Where it triggered a fault on strlen(key) where key was the filename.
The reason is that filename is a char * to user space, and the histogram
code just blindly dereferenced it, with obvious bad results.
I originally tried to use strncpy_from_user/kernel_nofault() but found
that there's other places that its dereferenced and not worth the effort.
Just do not allow "char *" to act like strings.
Link: https://lkml.kernel.org/r/20210715000206.025df9d2@rorschach.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Tom Zanussi <zanussi@kernel.org>
Fixes:
79e577cbce4c4 ("tracing: Support string type key properly")
Fixes:
5967bd5c4239 ("tracing: Let filter_assign_type() detect FILTER_PTR_STRING")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Maier [Fri, 2 Jul 2021 16:09:22 +0000 (18:09 +0200)]
scsi: zfcp: Report port fc_security as unknown early during remote cable pull
commit
8b3bdd99c092bbaeaa7d9eecb1a3e5dc9112002b upstream.
On remote cable pull, a zfcp_port keeps its status and only gets
ZFCP_STATUS_PORT_LINK_TEST added. Only after an ADISC timeout, we would
actually start port recovery and remove ZFCP_STATUS_COMMON_UNBLOCKED which
zfcp_sysfs_port_fc_security_show() detected and reported as "unknown"
instead of the old and possibly stale zfcp_port->connection_info.
Add check for ZFCP_STATUS_PORT_LINK_TEST for timely "unknown" report.
Link: https://lore.kernel.org/r/20210702160922.2667874-1-maier@linux.ibm.com
Fixes:
a17c78460093 ("scsi: zfcp: report FC Endpoint Security in sysfs")
Cc: <stable@vger.kernel.org> #5.7+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tyrel Datwyler [Thu, 1 Jul 2021 19:56:59 +0000 (13:56 -0600)]
scsi: core: Fix bad pointer dereference when ehandler kthread is invalid
commit
93aa71ad7379900e61c8adff6a710a4c18c7c99b upstream.
Commit
66a834d09293 ("scsi: core: Fix error handling of scsi_host_alloc()")
changed the allocation logic to call put_device() to perform host cleanup
with the assumption that IDA removal and stopping the kthread would
properly be performed in scsi_host_dev_release(). However, in the unlikely
case that the error handler thread fails to spawn, shost->ehandler is set
to ERR_PTR(-ENOMEM).
The error handler cleanup code in scsi_host_dev_release() will call
kthread_stop() if shost->ehandler != NULL which will always be the case
whether the kthread was successfully spawned or not. In the case that it
failed to spawn this has the nasty side effect of trying to dereference an
invalid pointer when kthread_stop() is called. The following splat provides
an example of this behavior in the wild:
scsi host11: error handler thread failed to spawn, error = -4
Kernel attempted to read user page (10c) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x0000010c
Faulting instruction address: 0xc00000000818e9a8
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: ibmvscsi(+) scsi_transport_srp dm_multipath dm_mirror dm_region
hash dm_log dm_mod fuse overlay squashfs loop
CPU: 12 PID: 274 Comm: systemd-udevd Not tainted 5.13.0-rc7 #1
NIP:
c00000000818e9a8 LR:
c0000000089846e8 CTR:
0000000000007ee8
REGS:
c000000037d12ea0 TRAP: 0300 Not tainted (5.13.0-rc7)
MSR:
800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR:
28228228
XER:
20040001
CFAR:
c0000000089846e4 DAR:
000000000000010c DSISR:
40000000 IRQMASK: 0
GPR00:
c0000000089846e8 c000000037d13140 c000000009cc1100 fffffffffffffffc
GPR04:
0000000000000001 0000000000000000 0000000000000000 c000000037dc0000
GPR08:
0000000000000000 c000000037dc0000 0000000000000001 00000000fffff7ff
GPR12:
0000000000008000 c00000000a049000 c000000037d13d00 000000011134d5a0
GPR16:
0000000000001740 c0080000190d0000 c0080000190d1740 c000000009129288
GPR20:
c000000037d13bc0 0000000000000001 c000000037d13bc0 c0080000190b7898
GPR24:
c0080000190b7708 0000000000000000 c000000033bb2c48 0000000000000000
GPR28:
c000000046b28280 0000000000000000 000000000000010c fffffffffffffffc
NIP [
c00000000818e9a8] kthread_stop+0x38/0x230
LR [
c0000000089846e8] scsi_host_dev_release+0x98/0x160
Call Trace:
[
c000000033bb2c48] 0xc000000033bb2c48 (unreliable)
[
c0000000089846e8] scsi_host_dev_release+0x98/0x160
[
c00000000891e960] device_release+0x60/0x100
[
c0000000087e55c4] kobject_release+0x84/0x210
[
c00000000891ec78] put_device+0x28/0x40
[
c000000008984ea4] scsi_host_alloc+0x314/0x430
[
c0080000190b38bc] ibmvscsi_probe+0x54/0xad0 [ibmvscsi]
[
c000000008110104] vio_bus_probe+0xa4/0x4b0
[
c00000000892a860] really_probe+0x140/0x680
[
c00000000892aefc] driver_probe_device+0x15c/0x200
[
c00000000892b63c] device_driver_attach+0xcc/0xe0
[
c00000000892b740] __driver_attach+0xf0/0x200
[
c000000008926f28] bus_for_each_dev+0xa8/0x130
[
c000000008929ce4] driver_attach+0x34/0x50
[
c000000008928fc0] bus_add_driver+0x1b0/0x300
[
c00000000892c798] driver_register+0x98/0x1a0
[
c00000000810eb60] __vio_register_driver+0x80/0xe0
[
c0080000190b4a30] ibmvscsi_module_init+0x9c/0xdc [ibmvscsi]
[
c0000000080121d0] do_one_initcall+0x60/0x2d0
[
c000000008261abc] do_init_module+0x7c/0x320
[
c000000008265700] load_module+0x2350/0x25b0
[
c000000008265cb4] __do_sys_finit_module+0xd4/0x160
[
c000000008031110] system_call_exception+0x150/0x2d0
[
c00000000800d35c] system_call_common+0xec/0x278
Fix this be nulling shost->ehandler when the kthread fails to spawn.
Link: https://lore.kernel.org/r/20210701195659.3185475-1-tyreld@linux.ibm.com
Fixes:
66a834d09293 ("scsi: core: Fix error handling of scsi_host_alloc()")
Cc: stable@vger.kernel.org
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lai Jiangshan [Mon, 28 Jun 2021 17:26:32 +0000 (01:26 +0800)]
KVM: X86: Disable hardware breakpoints unconditionally before kvm_x86->run()
commit
f85d40160691881a17a397c448d799dfc90987ba upstream.
When the host is using debug registers but the guest is not using them
nor is the guest in guest-debug state, the kvm code does not reset
the host debug registers before kvm_x86->run(). Rather, it relies on
the hardware vmentry instruction to automatically reset the dr7 registers
which ensures that the host breakpoints do not affect the guest.
This however violates the non-instrumentable nature around VM entry
and exit; for example, when a host breakpoint is set on vcpu->arch.cr2,
Another issue is consistency. When the guest debug registers are active,
the host breakpoints are reset before kvm_x86->run(). But when the
guest debug registers are inactive, the host breakpoints are delayed to
be disabled. The host tracing tools may see different results depending
on what the guest is doing.
To fix the problems, we clear %db7 unconditionally before kvm_x86->run()
if the host has set any breakpoints, no matter if the guest is using
them or not.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <
20210628172632.81029-1-jiangshanlai@gmail.com>
Cc: stable@vger.kernel.org
[Only clear %db7 instead of reloading all debug registers. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vitaly Kuznetsov [Mon, 28 Jun 2021 10:44:20 +0000 (12:44 +0200)]
KVM: nSVM: Check the value written to MSR_VM_HSAVE_PA
commit
fce7e152ffc8f89d02a80617b16c7aa1527847c8 upstream.
APM states that #GP is raised upon write to MSR_VM_HSAVE_PA when
the supplied address is not page-aligned or is outside of "maximum
supported physical address for this implementation".
page_address_valid() check seems suitable. Also, forcefully page-align
the address when it's written from VMM.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <
20210628104425.391276-2-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
[Add comment about behavior for host-provided values. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Wed, 23 Jun 2021 23:05:49 +0000 (16:05 -0700)]
KVM: x86/mmu: Do not apply HPA (memory encryption) mask to GPAs
commit
fc9bf2e087efcd81bda2e52d09616d2a1bf982a8 upstream.
Ignore "dynamic" host adjustments to the physical address mask when
generating the masks for guest PTEs, i.e. the guest PA masks. The host
physical address space and guest physical address space are two different
beasts, e.g. even though SEV's C-bit is the same bit location for both
host and guest, disabling SME in the host (which clears shadow_me_mask)
does not affect the guest PTE->GPA "translation".
For non-SEV guests, not dropping bits is the correct behavior. Assuming
KVM and userspace correctly enumerate/configure guest MAXPHYADDR, bits
that are lost as collateral damage from memory encryption are treated as
reserved bits, i.e. KVM will never get to the point where it attempts to
generate a gfn using the affected bits. And if userspace wants to create
a bogus vCPU, then userspace gets to deal with the fallout of hardware
doing odd things with bad GPAs.
For SEV guests, not dropping the C-bit is technically wrong, but it's a
moot point because KVM can't read SEV guest's page tables in any case
since they're always encrypted. Not to mention that the current KVM code
is also broken since sme_me_mask does not have to be non-zero for SEV to
be supported by KVM. The proper fix would be to teach all of KVM to
correctly handle guest private memory, but that's a task for the future.
Fixes:
d0ec49d4de90 ("kvm/x86/svm: Support Secure Memory Encryption within KVM")
Cc: stable@vger.kernel.org
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20210623230552.4027702-5-seanjc@google.com>
[Use a new header instead of adding header guards to paging_tmpl.h. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Wed, 23 Jun 2021 23:05:46 +0000 (16:05 -0700)]
KVM: x86: Use guest MAXPHYADDR from CPUID.0x8000_0008 iff TDP is enabled
commit
4bf48e3c0aafd32b960d341c4925b48f416f14a5 upstream.
Ignore the guest MAXPHYADDR reported by CPUID.0x8000_0008 if TDP, i.e.
NPT, is disabled, and instead use the host's MAXPHYADDR. Per AMD'S APM:
Maximum guest physical address size in bits. This number applies only
to guests using nested paging. When this field is zero, refer to the
PhysAddrSize field for the maximum guest physical address size.
Fixes:
24c82e576b78 ("KVM: Sanitize cpuid")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20210623230552.4027702-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kefeng Wang [Sat, 26 Jun 2021 07:03:04 +0000 (15:03 +0800)]
KVM: mmio: Fix use-after-free Read in kvm_vm_ioctl_unregister_coalesced_mmio
commit
23fa2e46a5556f787ce2ea1a315d3ab93cced204 upstream.
BUG: KASAN: use-after-free in kvm_vm_ioctl_unregister_coalesced_mmio+0x7c/0x1ec arch/arm64/kvm/../../../virt/kvm/coalesced_mmio.c:183
Read of size 8 at addr
ffff0000c03a2500 by task syz-executor083/4269
CPU: 5 PID: 4269 Comm: syz-executor083 Not tainted 5.10.0 #7
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2d0 arch/arm64/kernel/stacktrace.c:132
show_stack+0x28/0x34 arch/arm64/kernel/stacktrace.c:196
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x110/0x164 lib/dump_stack.c:118
print_address_description+0x78/0x5c8 mm/kasan/report.c:385
__kasan_report mm/kasan/report.c:545 [inline]
kasan_report+0x148/0x1e4 mm/kasan/report.c:562
check_memory_region_inline mm/kasan/generic.c:183 [inline]
__asan_load8+0xb4/0xbc mm/kasan/generic.c:252
kvm_vm_ioctl_unregister_coalesced_mmio+0x7c/0x1ec arch/arm64/kvm/../../../virt/kvm/coalesced_mmio.c:183
kvm_vm_ioctl+0xe30/0x14c4 arch/arm64/kvm/../../../virt/kvm/kvm_main.c:3755
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__arm64_sys_ioctl+0xf88/0x131c fs/ioctl.c:739
__invoke_syscall arch/arm64/kernel/syscall.c:36 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:48 [inline]
el0_svc_common arch/arm64/kernel/syscall.c:158 [inline]
do_el0_svc+0x120/0x290 arch/arm64/kernel/syscall.c:220
el0_svc+0x1c/0x28 arch/arm64/kernel/entry-common.c:367
el0_sync_handler+0x98/0x170 arch/arm64/kernel/entry-common.c:383
el0_sync+0x140/0x180 arch/arm64/kernel/entry.S:670
Allocated by task 4269:
stack_trace_save+0x80/0xb8 kernel/stacktrace.c:121
kasan_save_stack mm/kasan/common.c:48 [inline]
kasan_set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc+0xdc/0x120 mm/kasan/common.c:461
kasan_kmalloc+0xc/0x14 mm/kasan/common.c:475
kmem_cache_alloc_trace include/linux/slab.h:450 [inline]
kmalloc include/linux/slab.h:552 [inline]
kzalloc include/linux/slab.h:664 [inline]
kvm_vm_ioctl_register_coalesced_mmio+0x78/0x1cc arch/arm64/kvm/../../../virt/kvm/coalesced_mmio.c:146
kvm_vm_ioctl+0x7e8/0x14c4 arch/arm64/kvm/../../../virt/kvm/kvm_main.c:3746
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__arm64_sys_ioctl+0xf88/0x131c fs/ioctl.c:739
__invoke_syscall arch/arm64/kernel/syscall.c:36 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:48 [inline]
el0_svc_common arch/arm64/kernel/syscall.c:158 [inline]
do_el0_svc+0x120/0x290 arch/arm64/kernel/syscall.c:220
el0_svc+0x1c/0x28 arch/arm64/kernel/entry-common.c:367
el0_sync_handler+0x98/0x170 arch/arm64/kernel/entry-common.c:383
el0_sync+0x140/0x180 arch/arm64/kernel/entry.S:670
Freed by task 4269:
stack_trace_save+0x80/0xb8 kernel/stacktrace.c:121
kasan_save_stack mm/kasan/common.c:48 [inline]
kasan_set_track+0x38/0x6c mm/kasan/common.c:56
kasan_set_free_info+0x20/0x40 mm/kasan/generic.c:355
__kasan_slab_free+0x124/0x150 mm/kasan/common.c:422
kasan_slab_free+0x10/0x1c mm/kasan/common.c:431
slab_free_hook mm/slub.c:1544 [inline]
slab_free_freelist_hook mm/slub.c:1577 [inline]
slab_free mm/slub.c:3142 [inline]
kfree+0x104/0x38c mm/slub.c:4124
coalesced_mmio_destructor+0x94/0xa4 arch/arm64/kvm/../../../virt/kvm/coalesced_mmio.c:102
kvm_iodevice_destructor include/kvm/iodev.h:61 [inline]
kvm_io_bus_unregister_dev+0x248/0x280 arch/arm64/kvm/../../../virt/kvm/kvm_main.c:4374
kvm_vm_ioctl_unregister_coalesced_mmio+0x158/0x1ec arch/arm64/kvm/../../../virt/kvm/coalesced_mmio.c:186
kvm_vm_ioctl+0xe30/0x14c4 arch/arm64/kvm/../../../virt/kvm/kvm_main.c:3755
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__arm64_sys_ioctl+0xf88/0x131c fs/ioctl.c:739
__invoke_syscall arch/arm64/kernel/syscall.c:36 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:48 [inline]
el0_svc_common arch/arm64/kernel/syscall.c:158 [inline]
do_el0_svc+0x120/0x290 arch/arm64/kernel/syscall.c:220
el0_svc+0x1c/0x28 arch/arm64/kernel/entry-common.c:367
el0_sync_handler+0x98/0x170 arch/arm64/kernel/entry-common.c:383
el0_sync+0x140/0x180 arch/arm64/kernel/entry.S:670
If kvm_io_bus_unregister_dev() return -ENOMEM, we already call kvm_iodevice_destructor()
inside this function to delete 'struct kvm_coalesced_mmio_dev *dev' from list
and free the dev, but kvm_iodevice_destructor() is called again, it will lead
the above issue.
Let's check the the return value of kvm_io_bus_unregister_dev(), only call
kvm_iodevice_destructor() if the return value is 0.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Message-Id: <
20210626070304.143456-1-wangkefeng.wang@huawei.com>
Cc: stable@vger.kernel.org
Fixes:
5d3c4c79384a ("KVM: Stop looking for coalesced MMIO zones if the bus is destroyed", 2021-04-20)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paulo Alcantara [Mon, 12 Jul 2021 15:38:24 +0000 (12:38 -0300)]
cifs: handle reconnect of tcon when there is no cached dfs referral
commit
507345b5ae6a57b7ecd7550ff39282ed20de7b8d upstream.
When there is no cached DFS referral of tcon->dfs_path, then reconnect
to same share.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 26 Apr 2021 17:48:07 +0000 (10:48 -0700)]
certs: add 'x509_revocation_list' to gitignore
commit
81f202315856edb75a371f3376aa3a47543c16f0 upstream.
Commit
d1f044103dad ("certs: Add ability to preload revocation certs")
created a new generated file for revocation certs, but didn't tell git
to ignore it. Thus causing unnecessary "git status" noise after a
kernel build with CONFIG_SYSTEM_REVOCATION_LIST enabled.
Add the proper gitignore magic.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 19 Jul 2021 07:45:03 +0000 (09:45 +0200)]
Linux 5.10.51
Link: https://lore.kernel.org/r/20210715182558.381078833@linuxfoundation.org
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Link: https://lore.kernel.org/r/20210716182126.028243738@linuxfoundation.org
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Hulk Robot <hulkrobot@huawei.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Hulk Robot <hulkrobot@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chao Yu [Fri, 7 May 2021 10:10:38 +0000 (18:10 +0800)]
f2fs: fix to avoid racing on fsync_entry_slab by multi filesystem instances
commit
cad83c968c2ebe97905f900326988ed37146c347 upstream.
As syzbot reported, there is an use-after-free issue during f2fs recovery:
Use-after-free write at 0xffff88823bc16040 (in kfence-#10):
kmem_cache_destroy+0x1f/0x120 mm/slab_common.c:486
f2fs_recover_fsync_data+0x75b0/0x8380 fs/f2fs/recovery.c:869
f2fs_fill_super+0x9393/0xa420 fs/f2fs/super.c:3945
mount_bdev+0x26c/0x3a0 fs/super.c:1367
legacy_get_tree+0xea/0x180 fs/fs_context.c:592
vfs_get_tree+0x86/0x270 fs/super.c:1497
do_new_mount fs/namespace.c:2905 [inline]
path_mount+0x196f/0x2be0 fs/namespace.c:3235
do_mount fs/namespace.c:3248 [inline]
__do_sys_mount fs/namespace.c:3456 [inline]
__se_sys_mount+0x2f9/0x3b0 fs/namespace.c:3433
do_syscall_64+0x3f/0xb0 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
The root cause is multi f2fs filesystem instances can race on accessing
global fsync_entry_slab pointer, result in use-after-free issue of slab
cache, fixes to init/destroy this slab cache only once during module
init/destroy procedure to avoid this issue.
Reported-by: syzbot+9d90dad32dd9727ed084@syzkaller.appspotmail.com
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Skripkin [Fri, 30 Apr 2021 18:50:46 +0000 (21:50 +0300)]
ext4: fix memory leak in ext4_fill_super
commit
618f003199c6188e01472b03cdbba227f1dc5f24 upstream.
static int kthread(void *_create) will return -ENOMEM
or -EINTR in case of internal failure or
kthread_stop() call happens before threadfn call.
To prevent fancy error checking and make code
more straightforward we moved all cleanup code out
of kmmpd threadfn.
Also, dropped struct mmpd_data at all. Now struct super_block
is a threadfn data and struct buffer_head embedded into
struct ext4_sb_info.
Reported-by: syzbot+d9e482e303930fa4f6ff@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210430185046.15742-1-paskripkin@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo Handa [Mon, 12 Apr 2021 13:45:50 +0000 (22:45 +0900)]
smackfs: restrict bytes count in smk_set_cipso()
commit
49ec114a6e62d8d320037ce71c1aaf9650b3cafd upstream.
Oops, I failed to update subject line.
From
07571157c91b98ce1a4aa70967531e64b78e8346 Mon Sep 17 00:00:00 2001
From: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Date: Mon, 12 Apr 2021 22:25:06 +0900
Subject: smackfs: restrict bytes count in smk_set_cipso()
Commit
7ef4c19d245f3dc2 ("smackfs: restrict bytes count in smackfs write
functions") missed that count > SMK_CIPSOMAX check applies to only
format == SMK_FIXED24_FMT case.
Reported-by: syzbot <syzbot+77c53db50c9fff774e8e@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Skripkin [Sun, 6 Jun 2021 14:24:05 +0000 (17:24 +0300)]
jfs: fix GPF in diFree
commit
9d574f985fe33efd6911f4d752de6f485a1ea732 upstream.
Avoid passing inode with
JFS_SBI(inode->i_sb)->ipimap == NULL to
diFree()[1]. GFP will appear:
struct inode *ipimap = JFS_SBI(ip->i_sb)->ipimap;
struct inomap *imap = JFS_IP(ipimap)->i_imap;
JFS_IP() will return invalid pointer when ipimap == NULL
Call Trace:
diFree+0x13d/0x2dc0 fs/jfs/jfs_imap.c:853 [1]
jfs_evict_inode+0x2c9/0x370 fs/jfs/inode.c:154
evict+0x2ed/0x750 fs/inode.c:578
iput_final fs/inode.c:1654 [inline]
iput.part.0+0x3fe/0x820 fs/inode.c:1680
iput+0x58/0x70 fs/inode.c:1670
Reported-and-tested-by: syzbot+0a89a7b56db04c21a656@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Zimmermann [Thu, 29 Apr 2021 10:50:57 +0000 (12:50 +0200)]
drm/ast: Remove reference to struct drm_device.pdev
commit
0ecb51824e838372e01330752503ddf9c0430ef7 upstream.
Using struct drm_device.pdev is deprecated. Upcast with to_pci_dev()
from struct drm_device.dev to get the PCI device structure.
v9:
* fix remaining pdev references
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Fixes:
ba4e0339a6a3 ("drm/ast: Fixed CVE for DP501")
Cc: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Cc: kernel test robot <lkp@intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210429105101.25667-2-tzimmermann@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zou Wei [Tue, 8 Jun 2021 06:34:08 +0000 (14:34 +0800)]
pinctrl: mcp23s08: Fix missing unlock on error in mcp23s08_irq()
commit
884af72c90016cfccd5717439c86b48702cbf184 upstream.
Add the missing unlock before return from function mcp23s08_irq()
in the error handling case.
v1-->v2:
remove the "return IRQ_HANDLED" line
Fixes:
897120d41e7a ("pinctrl: mcp23s08: fix race condition in irq handler")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1623134048-56051-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikulas Patocka [Mon, 21 Jun 2021 18:48:29 +0000 (14:48 -0400)]
dm writecache: write at least 4k when committing
commit
867de40c4c23e6d7f89f9ce4272a5d1b1484c122 upstream.
SSDs perform badly with sub-4k writes (because they perfrorm
read-modify-write internally), so make sure writecache writes at least
4k when committing.
Fixes:
991bd8d7bc78 ("dm writecache: commit just one block, not a full page")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yang Yingliang [Thu, 15 Jul 2021 13:18:25 +0000 (21:18 +0800)]
io_uring: fix clear IORING_SETUP_R_DISABLED in wrong function
In commit
3ebba796fa25 ("io_uring: ensure that SQPOLL thread is started for exit"),
the IORING_SETUP_R_DISABLED is cleared in io_sq_offload_start(), but when backport
it to stable-5.10, IORING_SETUP_R_DISABLED is cleared in __io_req_task_submit(),
move clearing IORING_SETUP_R_DISABLED to io_sq_offload_start() to fix this.
Fixes:
6cae8095490ca ("io_uring: ensure that SQPOLL thread is started for exit")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Drung [Sat, 5 Jun 2021 20:15:36 +0000 (22:15 +0200)]
media: uvcvideo: Fix pixel format change for Elgato Cam Link 4K
commit
4c6e0976295add7f0ed94d276c04a3d6f1ea8f83 upstream.
The Elgato Cam Link 4K HDMI video capture card reports to support three
different pixel formats, where the first format depends on the connected
HDMI device.
```
$ v4l2-ctl -d /dev/video0 --list-formats-ext
ioctl: VIDIOC_ENUM_FMT
Type: Video Capture
[0]: 'NV12' (Y/CbCr 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
[1]: 'NV12' (Y/CbCr 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
[2]: 'YU12' (Planar YUV 4:2:0)
Size: Discrete 3840x2160
Interval: Discrete 0.033s (29.970 fps)
```
Changing the pixel format to anything besides the first pixel format
does not work:
```
$ v4l2-ctl -d /dev/video0 --try-fmt-video pixelformat=YU12
Format Video Capture:
Width/Height : 3840/2160
Pixel Format : 'NV12' (Y/CbCr 4:2:0)
Field : None
Bytes per Line : 3840
Size Image :
12441600
Colorspace : sRGB
Transfer Function : Rec. 709
YCbCr/HSV Encoding: Rec. 709
Quantization : Default (maps to Limited Range)
Flags :
```
User space applications like VLC might show an error message on the
terminal in that case:
```
libv4l2: error set_fmt gave us a different result than try_fmt!
```
Depending on the error handling of the user space applications, they
might display a distorted video, because they use the wrong pixel format
for decoding the stream.
The Elgato Cam Link 4K responds to the USB video probe
VS_PROBE_CONTROL/VS_COMMIT_CONTROL with a malformed data structure: The
second byte contains bFormatIndex (instead of being the second byte of
bmHint). The first byte is always zero. The third byte is always 1.
The firmware bug was reported to Elgato on 2020-12-01 and it was
forwarded by the support team to the developers as feature request.
There is no firmware update available since then. The latest firmware
for Elgato Cam Link 4K as of 2021-03-23 has MCU 20.02.19 and FPGA 67.
Therefore correct the malformed data structure for this device. The
change was successfully tested with VLC, OBS, and Chromium using
different pixel formats (YUYV, NV12, YU12), resolutions (3840x2160,
1920x1080), and frame rates (29.970 and 59.940 fps).
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Drung <bdrung@posteo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 24 May 2021 11:09:19 +0000 (13:09 +0200)]
media: gspca/sunplus: fix zero-length control requests
commit
b4bb4d425b7b02424afea2dfdcd77b3b4794175e upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the single zero-length control request which was using the
read-register helper, and update the helper so that zero-length reads
fail with an error message instead.
Fixes:
6a7eba24e4f0 ("V4L/DVB (8157): gspca: all subdrivers")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 21 May 2021 13:28:39 +0000 (15:28 +0200)]
media: gspca/sq905: fix control-request direction
commit
53ae298fde7adcc4b1432bce2dbdf8dac54dfa72 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the USB_REQ_SYNCH_FRAME request which erroneously used
usb_sndctrlpipe().
Fixes:
27d35fc3fb06 ("V4L/DVB (10639): gspca - sq905: New subdriver.")
Cc: stable@vger.kernel.org # 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Skripkin [Mon, 17 May 2021 19:18:14 +0000 (21:18 +0200)]
media: zr364xx: fix memory leak in zr364xx_start_readpipe
commit
0a045eac8d0427b64577a24d74bb8347c905ac65 upstream.
syzbot reported memory leak in zr364xx driver.
The problem was in non-freed urb in case of
usb_submit_urb() fail.
backtrace:
[<
ffffffff82baedf6>] kmalloc include/linux/slab.h:561 [inline]
[<
ffffffff82baedf6>] usb_alloc_urb+0x66/0xe0 drivers/usb/core/urb.c:74
[<
ffffffff82f7cce8>] zr364xx_start_readpipe+0x78/0x130 drivers/media/usb/zr364xx/zr364xx.c:1022
[<
ffffffff84251dfc>] zr364xx_board_init drivers/media/usb/zr364xx/zr364xx.c:1383 [inline]
[<
ffffffff84251dfc>] zr364xx_probe+0x6a3/0x851 drivers/media/usb/zr364xx/zr364xx.c:1516
[<
ffffffff82bb6507>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<
ffffffff826018a9>] really_probe+0x159/0x500 drivers/base/dd.c:576
Fixes:
ccbf035ae5de ("V4L/DVB (12278): zr364xx: implement V4L2_CAP_STREAMING")
Cc: stable@vger.kernel.org
Reported-by: syzbot+af4fa391ef18efdd5f69@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Fri, 21 May 2021 13:28:38 +0000 (15:28 +0200)]
media: dtv5100: fix control-request directions
commit
8c8b9a9be2afa8bd6a72ad1130532baab9fab89d upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the control requests which erroneously used usb_rcvctrlpipe().
Fixes:
8466028be792 ("V4L/DVB (8734): Initial support for AME DTV-5100 USB2.0 DVB-T")
Cc: stable@vger.kernel.org # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Mon, 14 Jun 2021 10:34:09 +0000 (12:34 +0200)]
media: subdev: disallow ioctl for saa6588/davinci
commit
0a7790be182d32b9b332a37cb4206e24fe94b728 upstream.
The saa6588_ioctl() function expects to get called from other kernel
functions with a 'saa6588_command' pointer, but I found nothing stops it
from getting called from user space instead, which seems rather dangerous.
The same thing happens in the davinci vpbe driver with its VENC_GET_FLD
command.
As a quick fix, add a separate .command() callback pointer for this
driver and change the two callers over to that. This change can easily
get backported to stable kernels if necessary, but since there are only
two drivers, we may want to eventually replace this with a set of more
specialized callbacks in the long run.
Fixes:
c3fda7f835b0 ("V4L/DVB (10537): saa6588: convert to v4l2_subdev.")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Thu, 24 Jun 2021 22:26:20 +0000 (00:26 +0200)]
PCI: aardvark: Implement workaround for the readback value of VEND_ID
commit
7f71a409fe3d9358da07c77f15bb5b7960f12253 upstream.
Marvell Armada 3700 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in aardvark driver for both PCI vendor id and PCI
subsystem vendor id.
This change affects and fixes PCI vendor id of emulated PCIe root bridge.
After this change emulated PCIe root bridge has correct vendor id.
Link: https://lore.kernel.org/r/20210624222621.4776-5-pali@kernel.org
Fixes:
8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár [Thu, 24 Jun 2021 21:33:43 +0000 (23:33 +0200)]
PCI: aardvark: Fix checking for PIO Non-posted Request
commit
8ceeac307a79f68c0d0c72d6e48b82fa424204ec upstream.
PIO_NON_POSTED_REQ for PIO_STAT register is incorrectly defined. Bit 10 in
register PIO_STAT indicates the response is to a non-posted request.
Link: https://lore.kernel.org/r/20210624213345.3617-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Konstantin Kharlamov [Thu, 20 May 2021 23:55:01 +0000 (02:55 +0300)]
PCI: Leave Apple Thunderbolt controllers on for s2idle or standby
commit
4694ae373dc2114f9a82f6ae15737e65af0c6dea upstream.
On Macbook 2013, resuming from suspend-to-idle or standby resulted in the
external monitor no longer being detected, a stacktrace, and errors like
this in dmesg:
pcieport 0000:06:00.0: can't change power state from D3hot to D0 (config space inaccessible)
The reason is that we know how to turn power to the Thunderbolt controller
*off* via the SXIO/SXFP/SXLF methods, but we don't know how to turn power
back on. We have to rely on firmware to turn the power back on.
When going to the "suspend-to-idle" or "standby" system sleep states,
firmware is not involved either on the suspend side or the resume side, so
we can't use SXIO/SXFP/SXLF to turn the power off.
Skip SXIO/SXFP/SXLF when firmware isn't involved in suspend, e.g., when
we're going to the "suspend-to-idle" or "standby" system sleep states.
Fixes:
1df5172c5c25 ("PCI: Suspend/resume quirks for Apple thunderbolt")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212767
Link: https://lore.kernel.org/r/20210520235501.917397-1-Hi-Angel@yandex.ru
Signed-off-by: Konstantin Kharlamov <Hi-Angel@yandex.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hou Tao [Thu, 17 Jun 2021 07:45:47 +0000 (15:45 +0800)]
dm btree remove: assign new_root only when removal succeeds
commit
b6e58b5466b2959f83034bead2e2e1395cca8aeb upstream.
remove_raw() in dm_btree_remove() may fail due to IO read error
(e.g. read the content of origin block fails during shadowing),
and the value of shadow_spine::root is uninitialized, but
the uninitialized value is still assign to new_root in the
end of dm_btree_remove().
For dm-thin, the value of pmd->details_root or pmd->root will become
an uninitialized value, so if trying to read details_info tree again
out-of-bound memory may occur as showed below:
general protection fault, probably for non-canonical address 0x3fdcb14c8d7520
CPU: 4 PID: 515 Comm: dmsetup Not tainted 5.13.0-rc6
Hardware name: QEMU Standard PC
RIP: 0010:metadata_ll_load_ie+0x14/0x30
Call Trace:
sm_metadata_count_is_more_than_one+0xb9/0xe0
dm_tm_shadow_block+0x52/0x1c0
shadow_step+0x59/0xf0
remove_raw+0xb2/0x170
dm_btree_remove+0xf4/0x1c0
dm_pool_delete_thin_device+0xc3/0x140
pool_message+0x218/0x2b0
target_message+0x251/0x290
ctl_ioctl+0x1c4/0x4d0
dm_ctl_ioctl+0xe/0x20
__x64_sys_ioctl+0x7b/0xb0
do_syscall_64+0x40/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixing it by only assign new_root when removal succeeds
Signed-off-by: Hou Tao <houtao1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikulas Patocka [Tue, 15 Jun 2021 17:45:55 +0000 (13:45 -0400)]
dm writecache: flush origin device when writing and cache is full
commit
ee55b92a7391bf871939330f662651b54be51b73 upstream.
Commit
d53f1fafec9d086f1c5166436abefdaef30e0363 ("dm writecache: do
direct write if the cache is full") changed dm-writecache, so that it
writes directly to the origin device if the cache is full.
Unfortunately, it doesn't forward flush requests to the origin device,
so that there is a bug where flushes are being ignored.
Fix this by adding missing flush forwarding.
For PMEM mode, we fix this bug by disabling direct writes to the origin
device, because it performs better.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes:
d53f1fafec9d ("dm writecache: do direct write if the cache is full")
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Damien Le Moal [Wed, 19 May 2021 01:26:16 +0000 (10:26 +0900)]
dm zoned: check zone capacity
commit
bab68499428ed934f0493ac74197ed6f36204260 upstream.
The dm-zoned target cannot support zoned block devices with zones that
have a capacity smaller than the zone size (e.g. NVMe zoned namespaces)
due to the current chunk zone mapping implementation as it is assumed
that zones and chunks have the same size with all blocks usable.
If a zoned drive is found to have zones with a capacity different from
the zone size, fail the target initialization.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sai Prakash Ranjan [Mon, 14 Jun 2021 17:59:00 +0000 (11:59 -0600)]
coresight: tmc-etf: Fix global-out-of-bounds in tmc_update_etf_buffer()
commit
5fae8a946ac2df879caf3f79a193d4766d00239b upstream.
commit
6f755e85c332 ("coresight: Add helper for inserting synchronization
packets") removed trailing '\0' from barrier_pkt array and updated the
call sites like etb_update_buffer() to have proper checks for barrier_pkt
size before read but missed updating tmc_update_etf_buffer() which still
reads barrier_pkt past the array size resulting in KASAN out-of-bounds
bug. Fix this by adding a check for barrier_pkt size before accessing
like it is done in etb_update_buffer().
BUG: KASAN: global-out-of-bounds in tmc_update_etf_buffer+0x4b8/0x698
Read of size 4 at addr
ffffffd05b7d1030 by task perf/2629
Call trace:
dump_backtrace+0x0/0x27c
show_stack+0x20/0x2c
dump_stack+0x11c/0x188
print_address_description+0x3c/0x4a4
__kasan_report+0x140/0x164
kasan_report+0x10/0x18
__asan_report_load4_noabort+0x1c/0x24
tmc_update_etf_buffer+0x4b8/0x698
etm_event_stop+0x248/0x2d8
etm_event_del+0x20/0x2c
event_sched_out+0x214/0x6f0
group_sched_out+0xd0/0x270
ctx_sched_out+0x2ec/0x518
__perf_event_task_sched_out+0x4fc/0xe6c
__schedule+0x1094/0x16a0
preempt_schedule_irq+0x88/0x170
arm64_preempt_schedule_irq+0xf0/0x18c
el1_irq+0xe8/0x180
perf_event_exec+0x4d8/0x56c
setup_new_exec+0x204/0x400
load_elf_binary+0x72c/0x18c0
search_binary_handler+0x13c/0x420
load_script+0x500/0x6c4
search_binary_handler+0x13c/0x420
exec_binprm+0x118/0x654
__do_execve_file+0x77c/0xba4
__arm64_compat_sys_execve+0x98/0xac
el0_svc_common+0x1f8/0x5e0
el0_svc_compat_handler+0x84/0xb0
el0_svc_compat+0x10/0x50
The buggy address belongs to the variable:
barrier_pkt+0x10/0x40
Memory state around the buggy address:
ffffffd05b7d0f00: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
ffffffd05b7d0f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
ffffffd05b7d1000: 00 00 00 00 00 00 fa fa fa fa fa fa 00 00 00 03
^
ffffffd05b7d1080: fa fa fa fa 00 02 fa fa fa fa fa fa 03 fa fa fa
ffffffd05b7d1100: fa fa fa fa 00 00 00 00 05 fa fa fa fa fa fa fa
==================================================================
Link: https://lore.kernel.org/r/20210505093430.18445-1-saiprakash.ranjan@codeaurora.org
Fixes:
0c3fc4d5fa26 ("coresight: Add barrier packet for synchronisation")
Cc: stable@vger.kernel.org
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210614175901.532683-6-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeremy Linton [Mon, 14 Jun 2021 17:59:01 +0000 (11:59 -0600)]
coresight: Propagate symlink failure
commit
51dd19a7e9f8fbbb7cd92b8a357091911eae7f78 upstream.
If the symlink is unable to be created, the driver goes
ahead and continues device creation. Instead lets propagate
the failure, and fail the probe.
Link: https://lore.kernel.org/r/20210526204042.2681700-1-jeremy.linton@arm.com
Fixes:
8a7365c2d418 ("coresight: Expose device connections via sysfs")
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210614175901.532683-7-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>