ipc/sem.c: make semctl(,,{GETNCNT,GETZCNT}) standard compliant

SUSv4 clearly defines how semncnt and semzcnt must be calculated: A task
waits on exactly one semaphore: The semaphore from the first operation
in the sop array that cannot proceed.

The Linux implementation never followed the standard, it tried to count
all semaphores that might be the reason why a task sleeps.

This patch fixes that.

Note:
a) The implementation assumes that GETNCNT and GETZCNT are rare operations,
   therefore the code counts them only on demand.
   (If they wouldn't be rare, then the non-compliance would have
   been found earlier)

b) compared to the initial version of the patch, the BUG_ONs were removed
   and it was clarified that the new behavior conforms to SUS.

Back-compatibility concerns:

Manfred:

: - there is no application in Fedora that uses GETNCNT or GETZCNT.
:
: - application that use only single-sop semop() are also safe, the
:   difference only affects complex apps.
:
: - portable application are also safe, the new behavior is standard
:   compliant.
:
: But that's it.  The old behavior existed in Linux from 0.99.something
: until now.

Michael:

: * These operations seem to be very little used.  Grepping the public
:   source that is contained Fedora 20 source DVD, there appear to be no
:   uses.  Of course, this says nothing about uses in private /
:   non-mainstream FOSS code, but it seems likely that the same pattern
:   is followed there.
:
: * The existing behavior is hard enough to understand that I suspect
:   that no one understood it well enough to rely on it anyway
:   (especially as that behavior contradicted both man page and POSIX).
:
: So, there's a chance of breakage, but I estimate that it's minute.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/sem.c: store which operation blocks in perform_atomic_semop()

Preparation for the next patch:

In the slow-path of perform_atomic_semop(), store a pointer to the
operation that caused the operation to block.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/sem.c: change perform_atomic_semop parameters

Right now, perform_atomic_semop gets the content of sem_queue as
individual fields.  Changes that, instead pass a pointer to sem_queue.

This is a preparation for the next patch: it uses sem_queue to store the
reason why a task must sleep.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/sem.c: remove code duplication

count_semzcnt and count_semncnt are more of less identical.  The patch
creates a single function that either counts the number of tasks waiting
for zero or waiting due to a decrease operation.

Compared to the initial version, the BUG_ONs were removed.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/sem.c: bugfix for semctl(,,GETZCNT)

GETZCNT is supposed to return the number of threads that wait until a
semaphore value becomes 0.

The current implementation overlooks complex operations that contain
both wait-for-zero operation and operations that alter at least one
semaphore.

The patch fixes that.  It's intentionally copy&paste, this will be
cleaned up in the next patch.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,msg: document volatile r_msg

The need for volatile is not obvious, document it.

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,msg: move some msgq ns code around

Nothing big and no logical changes, just get rid of some redundant
function declarations.  Move msg_[init/exit]_ns down the end of the
file.

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,msg: use current->state helpers

Call __set_current_state() instead of assigning the new state directly.

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Manfred Spraul <manfred@colorfullif.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc,shm: document new limits in the uapi header

This is useful in the future and allows users to better understand the
reasoning behind the changes.

Also use UL as we're dealing with it anyways.

Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/shm.c: increase the defaults for SHMALL, SHMMAX

System V shared memory

a) can be abused to trigger out-of-memory conditions and the standard
   measures against out-of-memory do not work:

    - it is not possible to use setrlimit to limit the size of shm segments.

    - segments can exist without association with any processes, thus
      the oom-killer is unable to free that memory.

b) is typically used for shared information - today often multiple GB.
   (e.g. database shared buffers)

The current default is a maximum segment size of 32 MB and a maximum
total size of 8 GB.  This is often too much for a) and not enough for
b), which means that lots of users must change the defaults.

This patch increases the default limits (nearly) to the maximum, which
is perfect for case b).  The defaults are used after boot and as the
initial value for each new namespace.

Admins/distros that need a protection against a) should reduce the
limits and/or enable shm_rmid_forced.

Unix has historically required setting these limits for shared memory,
and Linux inherited such behavior.  The consequence of this is added
complexity for users and administrators.  One very common example are
Database setup/installation documents and scripts, where users must
manually calculate the values for these limits.  This also requires
(some) knowledge of how the underlying memory management works, thus
causing, in many occasions, the limits to just be flat out wrong.
Disabling these limits sooner could have saved companies a lot of time,
headaches and money for support.  But it's never too late, simplify
users life now.

Further notes:
- The patch only changes default, overrides behave as before:
        # sysctl kernel.shmall=33554432
  would recreate the previous limit for SHMMAX (for the current namespace).

- Disabling sysv shm allocation is possible with:
        # sysctl kernel.shmall=0
  (not a new feature, also per-namespace)

- The limits are intentionally set to a value slightly less than ULONG_MAX,
  to avoid triggering overflows in user space apps.
  [not unreasonable, see http://marc.info/?l=linux-mm&m=139638334330127]

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reported-by: Davidlohr Bueso <davidlohr@hp.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/shm.c: check for integer overflow during shmget.

SHMMAX is the upper limit for the size of a shared memory segment, counted
in bytes.  The actual allocation is that size, rounded up to the next full
page.

Add a check that prevents the creation of segments where the rounded up
size causes an integer overflow.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/shm.c: check for overflows of shm_tot

shm_tot counts the total number of pages used by shm segments.

If SHMALL is ULONG_MAX (or nearly ULONG_MAX), then the number can
overflow.  Subsequent calls to shmctl(,SHM_INFO,) would return wrong
values for shm_tot.

The patch adds a detection for overflows.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc/shm.c: check for ulong overflows in shmat

The increase of SHMMAX/SHMALL is a 4 patch series.

The change itself is trivial, the only problem are interger overflows.
The overflows are not new, but if we make huge values the default, then
the code should be free from overflows.

SHMMAX:

- shmmem_file_setup places a hard limit on the segment size:
  MAX_LFS_FILESIZE.

  On 32-bit, the limit is > 1 TB, i.e. 4 GB-1 byte segments are
  possible. Rounded up to full pages the actual allocated size
  is 0. --> must be fixed, patch 3

- shmat:
  - find_vma_intersection does not handle overflows properly.
    --> must be fixed, patch 1

  - the rest is fine, do_mmap_pgoff limits mappings to TASK_SIZE
    and checks for overflows (i.e.: map 2 GB, starting from
    addr=2.5GB fails).

SHMALL:
- after creating 8192 segments size (1L<<63)-1, shm_tot overflows and
  returns 0.  --> must be fixed, patch 2.

Userspace:
- Obviously, there could be overflows in userspace. There is nothing
  we can do, only use values smaller than ULONG_MAX.
  I ended with "ULONG_MAX - 1L<<24":

  - TASK_SIZE cannot be used because it is the size of the current
    task. Could be 4G if it's a 32-bit task on a 64-bit kernel.

  - The maximum size is not standardized across archs:
    I found TASK_MAX_SIZE, TASK_SIZE_MAX and TASK_SIZE_64.

  - Just in case some arch revives a 4G/4G split, nearly
    ULONG_MAX is a valid segment size.

  - Using "0" as a magic value for infinity is even worse, because
    right now 0 means 0, i.e. fail all allocations.

This patch (of 4):

find_vma_intersection() does not work as intended if addr+size overflows.
The patch adds a manual check before the call to find_vma_intersection.

Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Davidlohr Bueso <davidlohr@hp.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc, kernel: clear whitespace

trailing whitespace

Signed-off-by: Paul McQuade <paulmcquad@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc, kernel: use Linux headers

Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Use #include <linux/types.h> instead of <asm/types.h>

Signed-off-by: Paul McQuade <paulmcquad@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: constify ipc_ops

There is no need to recreate the very same ipc_ops structure on every
kernel entry for msgget/semget/shmget.  Just declare it static and be
done with it.  While at it, constify it as we don't modify the structure
at runtime.

Found in the PaX patch, written by the PaX Team.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

initramfs: remove "compression mode" choice

Commit 9ba4bcb64589 ("initramfs: read CONFIG_RD_ variables for initramfs
compression") removed the users of the various INITRAMFS_COMPRESSION_*
Kconfig symbols.  So since v3.13 the entire "Built-in initramfs
compression mode" choice is a set of knobs connected to nothing.  The
entire choice can safely be removed.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: P J P <ppandit@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/devpts/inode.c: convert printk to pr_foo()

Also convert spaces to tabs (checkpatch warnings) if (!dentry) KERN_NOTICE
converted to pr_err (like if (!inode) error process)

[akpm@linux-foundation.org: use KBUILD_MODNAME, per Joe]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Joe Perches <joe@perches.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/cachefiles: replace kerror by pr_err

Also add pr_fmt in internal.h

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

FS/CACHEFILES: convert printk to pr_foo()

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/pstore: logging clean-up

- Define pr_fmt in plateform.c and ram_core.c for global prefix.

- Coalesce format fragments.

- Separate format/arguments on lines > 80 characters.

Note: Some pr_foo() were initially declared without prefix and therefore
this could break existing log analyzer.

[akpm@linux-foundation.org: missed a couple of prefix removals]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Joe Perches <joe@perches.com>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/profile.c: use static const char instead of static char

schedstr, sleepstr and kvmstr are only used in strcmp & strlen

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/profile.c: convert printk to pr_foo()

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/affs: pr_debug cleanup

- Remove AFFS: prefix (defined in pr_fmt)

- Use __func__

- Separate format/arguments on lines > 80 characters.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/affs: convert printk to pr_foo()

-All printk(KERN_foo converted to pr_foo()

-Default printk converted to pr_warn()

-Add pr_fmt to affs.h

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/affs/file.c: remove unnecessary function parameters

- affs_do_readpage_ofs is always called with from = 0 ie reading from
  page->index

- File parameter is never used

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/asm-generic/ioctl.h: fix _IOC_TYPECHECK sparse error

When running sparse over drivers/media/v4l2-core/v4l2-ioctl.c I get these
errors:

  drivers/media/v4l2-core/v4l2-ioctl.c:2043:9: error: bad integer constant expression
  drivers/media/v4l2-core/v4l2-ioctl.c:2044:9: error: bad integer constant expression
  drivers/media/v4l2-core/v4l2-ioctl.c:2045:9: error: bad integer constant expression
  drivers/media/v4l2-core/v4l2-ioctl.c:2046:9: error: bad integer constant expression

etc.

The root cause of that turns out to be in include/asm-generic/ioctl.h:

#include <uapi/asm-generic/ioctl.h>

/* provoke compile error for invalid uses of size argument */
extern unsigned int __invalid_size_argument_for_IOC;
#define _IOC_TYPECHECK(t) \
        ((sizeof(t) == sizeof(t[1]) && \
          sizeof(t) < (1 << _IOC_SIZEBITS)) ? \
          sizeof(t) : __invalid_size_argument_for_IOC)

If it is defined as this (as is already done if __KERNEL__ is not defined):

  #define _IOC_TYPECHECK(t) (sizeof(t))

then all is well with the world.

This patch allows sparse to work correctly.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/user_namespace.c: kernel-doc/checkpatch fixes

-uid->gid
-split some function declarations
-if/then/else warning

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tools/testing/selftests/sysctl: validate sysctl_writes_strict

This adds several behavioral tests to sysctl string and number writing
to detect unexpected cases that behaved differently when the sysctl
kernel.sysctl_writes_strict != 1.

[ original ]
    root@localhost:~# make test_num
    == Testing sysctl behavior against /proc/sys/kernel/domainname ==
    Writing test file ... ok
    Checking sysctl is not set to test value ... ok
    Writing sysctl from shell ... ok
    Resetting sysctl to original value ... ok
    Writing entire sysctl in single write ... ok
    Writing middle of sysctl after synchronized seek ... FAIL
    Writing beyond end of sysctl ... FAIL
    Writing sysctl with multiple long writes ... FAIL
    Writing entire sysctl in short writes ... FAIL
    Writing middle of sysctl after unsynchronized seek ... ok
    Checking sysctl maxlen is at least 65 ... ok
    Checking sysctl keeps original string on overflow append ... FAIL
    Checking sysctl stays NULL terminated on write ... ok
    Checking sysctl stays NULL terminated on overwrite ... ok
    make: *** [test_num] Error 1
    root@localhost:~# make test_string
    == Testing sysctl behavior against /proc/sys/vm/swappiness ==
    Writing test file ... ok
    Checking sysctl is not set to test value ... ok
    Writing sysctl from shell ... ok
    Resetting sysctl to original value ... ok
    Writing entire sysctl in single write ... ok
    Writing middle of sysctl after synchronized seek ... FAIL
    Writing beyond end of sysctl ... FAIL
    Writing sysctl with multiple long writes ... ok
    make: *** [test_string] Error 1

[ with CONFIG_PROC_SYSCTL_STRICT_WRITES ]
    root@localhost:~# make run_tests
    == Testing sysctl behavior against /proc/sys/kernel/domainname ==
    Writing test file ... ok
    Checking sysctl is not set to test value ... ok
    Writing sysctl from shell ... ok
    Resetting sysctl to original value ... ok
    Writing entire sysctl in single write ... ok
    Writing middle of sysctl after synchronized seek ... ok
    Writing beyond end of sysctl ... ok
    Writing sysctl with multiple long writes ... ok
    Writing entire sysctl in short writes ... ok
    Writing middle of sysctl after unsynchronized seek ... ok
    Checking sysctl maxlen is at least 65 ... ok
    Checking sysctl keeps original string on overflow append ... ok
    Checking sysctl stays NULL terminated on write ... ok
    Checking sysctl stays NULL terminated on overwrite ... ok
    == Testing sysctl behavior against /proc/sys/vm/swappiness ==
    Writing test file ... ok
    Checking sysctl is not set to test value ... ok
    Writing sysctl from shell ... ok
    Resetting sysctl to original value ... ok
    Writing entire sysctl in single write ... ok
    Writing middle of sysctl after synchronized seek ... ok
    Writing beyond end of sysctl ... ok
    Writing sysctl with multiple long writes ... ok

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sysctl: allow for strict write position handling

When writing to a sysctl string, each write, regardless of VFS position,
begins writing the string from the start.  This means the contents of
the last write to the sysctl controls the string contents instead of the
first:

  open("/proc/sys/kernel/modprobe", O_WRONLY)   = 1
  write(1, "AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA"..., 4096) = 4096
  write(1, "/bin/true", 9)                = 9
  close(1)                                = 0

  $ cat /proc/sys/kernel/modprobe
  /bin/true

Expected behaviour would be to have the sysctl be "AAAA..." capped at
maxlen (in this case KMOD_PATH_LEN: 256), instead of truncating to the
contents of the second write.  Similarly, multiple short writes would
not append to the sysctl.

The old behavior is unlike regular POSIX files enough that doing audits
of software that interact with sysctls can end up in unexpected or
dangerous situations.  For example, "as long as the input starts with a
trusted path" turns out to be an insufficient filter, as what must also
happen is for the input to be entirely contained in a single write
syscall -- not a common consideration, especially for high level tools.

This provides kernel.sysctl_writes_strict as a way to make this behavior
act in a less surprising manner for strings, and disallows non-zero file
position when writing numeric sysctls (similar to what is already done
when reading from non-zero file positions).  For now, the default (0) is
to warn about non-zero file position use, but retain the legacy
behavior.  Setting this to -1 disables the warning, and setting this to
1 enables the file position respecting behavior.

[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: move misplaced hunk, per Randy]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sysctl: refactor sysctl string writing logic

Consolidate buffer length checking with new-line/end-of-line checking.
Additionally, instead of reading user memory twice, just do the
assignment during the loop.

This change doesn't affect the potential races here.  It was already
possible to read a sysctl that was in the middle of a write.  In both
cases, the string will always be NULL terminated.  The pre-existing race
remains a problem to be solved.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sysctl: clean up char buffer arguments

When writing to a sysctl string, each write, regardless of VFS position,
began writing the string from the start.  This meant the contents of the
last write to the sysctl controlled the string contents instead of the
first.

This misbehavior was featured in an exploit against Chrome OS.  While
it's not in itself a vulnerability, it's a weirdness that isn't on the
mind of most auditors: "This filter looks correct, the first line
written would not be meaningful to sysctl" doesn't apply here, since the
size of the write and the contents of the final write are what matter
when writing to sysctls.

This adds the sysctl kernel.sysctl_writes_strict to control the write
behavior.  The default (0) reports when VFS position is non-0 on a
write, but retains legacy behavior, -1 disables the warning, and 1
enables the position-respecting behavior.

The long-term plan here is to wait for userspace to be fixed in response
to the new warning and to then switch the default kernel behavior to the
new position-respecting behavior.

This patch (of 4):

The char buffer arguments are needlessly cast in weird places.  Clean it
up so things are easier to read.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rapidio/tsi721: use pci_enable_msix_exact() instead of pci_enable_msix()

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers using these two
interfaces need to be updated to use the new pci_enable_msi_range() or
pci_enable_msi_exact() and pci_enable_msix_range() or
pci_enable_msix_exact() interfaces.

The patch has no runtime effect.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: reorder the fields

idr_layer->layer is always accessed in read path, move it in the front.

idr_layer->bitmap is moved on the bottom.  And rcu_head shares with
bitmap due to they do not be accessed at the same time.

idr->id_free/id_free_cnt/lock are free list fields, and moved to the
bottom.  They will be removed in near future.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: reduce the unneeded check in free_layer()

If "idr->hint == p" is true, it also implies "idr->hint" is true(not NULL).

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: don't need to shink the free list when idr_remove()

After idr subsystem is changed to RCU-awared, the free layer will not go
to the free list.  The free list will not be filled up when
idr_remove().  So we don't need to shink it too.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: fix idr_replace()'s returned error code

When the smaller id is not found, idr_replace() returns -ENOENT.  But
when the id is bigger enough, idr_replace() returns -EINVAL, actually
there is no difference between these two kinds of ids.

These are all unallocated id, the return values of the idr_replace() for
these ids should be the same: -ENOENT.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: fix NULL pointer dereference when ida_remove(unallocated_id)

If the ida has at least one existing id, and when an unallocated ID
which meets a certain condition is passed to the ida_remove(), the
system will crash because it hits NULL pointer dereference.

The condition is that the unallocated ID shares the same lowest idr
layer with the existing ID, but the idr slot would be different if the
unallocated ID were to be allocated.

In this case the matching idr slot for the unallocated_id is NULL,
causing @bitmap to be NULL which the function dereferences without
checking crashing the kernel.

See the test code:

  static void test3(void)
  {
        int id;
        DEFINE_IDA(test_ida);

        printk(KERN_INFO "Start test3\n");
        if (ida_pre_get(&test_ida, GFP_KERNEL) < 0) return;
        if (ida_get_new(&test_ida,  &id) < 0) return;
        ida_remove(&test_ida, 4000); /* bug: null deference here */
        printk(KERN_INFO "End of test3\n");
  }

It happens only when the caller tries to free an unallocated ID which is
the caller's fault.  It is not a bug.  But it is better to add the
proper check and complain rather than crashing the kernel.

[tj@kernel.org: updated patch description]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: fix unexpected ID-removal when idr_remove(unallocated_id)

If unallocated_id = (ANY * idr_max(idp->layers) + existing_id) is passed
to idr_remove().  The existing_id will be removed unexpectedly.

The following test shows this unexpected id-removal:

  static void test4(void)
  {
        int id;
        DEFINE_IDR(test_idr);

        printk(KERN_INFO "Start test4\n");
        id = idr_alloc(&test_idr, (void *)1, 42, 43, GFP_KERNEL);
        BUG_ON(id != 42);
        idr_remove(&test_idr, 42 + IDR_SIZE);
        TEST_BUG_ON(idr_find(&test_idr, 42) != (void *)1);
        idr_destroy(&test_idr);
        printk(KERN_INFO "End of test4\n");
  }

ida_remove() shares the similar problem.

It happens only when the caller tries to free an unallocated ID which is
the caller's fault.  It is not a bug.  But it is better to add the
proper check and complain rather than removing an existing_id silently.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

idr: fix overflow bug during maximum ID calculation at maximum height

idr_replace() open-codes the logic to calculate the maximum valid ID
given the height of the idr tree; unfortunately, the open-coded logic
doesn't account for the fact that the top layer may have unused slots
and over-shifts the limit to zero when the tree is at its maximum
height.

The following test code shows it fails to replace the value for
id=((1<<27)+42):

  static void test5(void)
  {
        int id;
        DEFINE_IDR(test_idr);
  #define TEST5_START ((1<<27)+42) /* use the highest layer */

        printk(KERN_INFO "Start test5\n");
        id = idr_alloc(&test_idr, (void *)1, TEST5_START, 0, GFP_KERNEL);
        BUG_ON(id != TEST5_START);
        TEST_BUG_ON(idr_replace(&test_idr, (void *)2, TEST5_START) != (void *)1);
        idr_destroy(&test_idr);
        printk(KERN_INFO "End of test5\n");
  }

Fix the bug by using idr_max() which correctly takes into account the
maximum allowed shift.

sub_alloc() shares the same problem and may incorrectly fail with
-EAGAIN; however, this bug doesn't affect correct operation because
idr_get_empty_slot(), which already uses idr_max(), retries with the
increased @id in such cases.

[tj@kernel.org: Updated patch description.]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/kexec.c: convert printk to pr_foo()

+ some pr_warning -> pr_warn and checkpatch warning fixes

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/panic.c: add "crash_kexec_post_notifiers" option for kdump after panic_notifers

Add a "crash_kexec_post_notifiers" boot option to run kdump after
running panic_notifiers and dump kmsg.  This can help rare situations
where kdump fails because of unstable crashed kernel or hardware failure
(memory corruption on critical data/code), or the 2nd kernel is already
broken by the 1st kernel (it's a broken behavior, but who can guarantee
that the "crashed" kernel works correctly?).

Usage: add "crash_kexec_post_notifiers" to kernel boot option.

Note that this actually increases risks of the failure of kdump.  This
option should be set only if you worry about the rare case of kdump
failure rather than increasing the chance of success.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Motohiro Kosaki <Motohiro.Kosaki@us.fujitsu.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Satoru MORIYA <satoru.moriya.br@hitachi.com>
Cc: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smp: print more useful debug info upon receiving IPI on an offline CPU

There is a longstanding problem related to CPU hotplug which causes IPIs
to be delivered to offline CPUs, and the smp-call-function IPI handler
code prints out a warning whenever this is detected.  Every once in a
while this (usually harmless) warning gets reported on LKML, but so far
it has not been completely fixed.  Usually the solution involves finding
out the IPI sender and fixing it by adding appropriate synchronization
with CPU hotplug.

However, while going through one such internal bug reports, I found that
there is a significant bug in the receiver side itself (more
specifically, in stop-machine) that can lead to this problem even when
the sender code is perfectly fine.  This patchset fixes that
synchronization problem in the CPU hotplug stop-machine code.

Patch 1 adds some additional debug code to the smp-call-function
framework, to help debug such issues easily.

Patch 2 modifies the stop-machine code to ensure that any IPIs that were
sent while the target CPU was online, would be noticed and handled by
that CPU without fail before it goes offline.  Thus, this avoids
scenarios where IPIs are received on offline CPUs (as long as the sender
uses proper hotplug synchronization).

In fact, I debugged the problem by using Patch 1, and found that the
payload of the IPI was always the block layer's trigger_softirq()
function.  But I was not able to find anything wrong with the block
layer code.  That's when I started looking at the stop-machine code and
realized that there is a race-window which makes the IPI _receiver_ the
culprit, not the sender.  Patch 2 fixes that race and hence this should
put an end to most of the hard-to-debug IPI-to-offline-CPU issues.

This patch (of 2):

Today the smp-call-function code just prints a warning if we get an IPI
on an offline CPU.  This info is sufficient to let us know that
something went wrong, but often it is very hard to debug exactly who
sent the IPI and why, from this info alone.

In most cases, we get the warning about the IPI to an offline CPU,
immediately after the CPU going offline comes out of the stop-machine
phase and reenables interrupts.  Since all online CPUs participate in
stop-machine, the information regarding the sender of the IPI is already
lost by the time we exit the stop-machine loop.  So even if we dump the
stack on each CPU at this point, we won't find anything useful since all
of them will show the stack-trace of the stopper thread.  So we need a
better way to figure out who sent the IPI and why.

To achieve this, when we detect an IPI targeted to an offline CPU, loop
through the call-single-data linked list and print out the payload
(i.e., the name of the function which was supposed to be executed by the
target CPU).  This would give us an insight as to who might have sent
the IPI and help us debug this further.

[akpm@linux-foundation.org: correctly suppress warning output on second and later occurrences]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mike Galbraith <mgalbraith@suse.de>
Cc: Gautham R Shenoy <ego@linux.vnet.ibm.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/proc/vmcore.c: remove NULL assignment to static

Static values are automatically initialized to NULL.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/proc/task_mmu.c: replace seq_printf by seq_puts

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: change wait_for_helper() to use kernel_sigaction()

Now that we have kernel_sigaction() we can change wait_for_helper() to
use it and cleans up the code a bit.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: introduce kernel_sigaction()

Now that allow_signal() is really trivial we can unify it with
disallow_signal().  Add the new helper, kernel_sigaction(), and
reimplement allow_signal/disallow_signal as a trivial wrappers.

This saves one EXPORT_SYMBOL() and the new helper can have more users.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: disallow_signal() should flush the potentially pending signal

disallow_signal() simply sets SIG_IGN, this is not enough and
recalc_sigpending() is simply pointless because in can never change the
state of TIF_SIGPENDING.

If we ignore a signal, we also need to do flush_sigqueue_mask() for the
case when this signal is pending, this way recalc_sigpending() can
actually clear TIF_SIGPENDING and we do not "leak" the allocated
siginfo's.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: kill the obsolete sigdelset() and recalc_sigpending() in allow_signal()

allow_signal() does sigdelset(current->blocked) due to historic reason,
previously it could be called by a daemonize()'ed kthread, and
daemonize() played with current->blocked.

Now that daemonize() has gone away we can remove sigdelset() and
recalc_sigpending().  If a user really wants to unblock a signal, it
must use sigprocmask() or set_current_block() explicitely.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: jffs2: fix the wrong usage of disallow_signal()

jffs2_garbage_collect_thread() does disallow_signal(SIGHUP) around
jffs2_garbage_collect_pass() and the comment says "We don't want SIGHUP
to interrupt us".

But disallow_signal() can't ensure that jffs2_garbage_collect_pass()
won't be interrupted by SIGHUP, the problem is that SIGHUP can be
already pending when disallow_signal() is called, and in this case any
interruptible sleep won't block.

Note: this is in fact because disallow_signal() is buggy and should be
fixed, see the next changes.

But there is another reason why disallow_signal() is wrong: SIG_IGN set
by disallow_signal() silently discards any SIGHUP which can be sent
before the next allow_signal(SIGHUP).

Change this code to use sigprocmask(SIG_UNBLOCK/SIG_BLOCK, SIGHUP).
This even matches the old (and wrong) semantics allow/disallow had when
this logic was written.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: mv {dis,}allow_signal() from sched.h/exit.c to signal.[ch]

Move the declaration/definition of allow_signal/disallow_signal to
signal.h/signal.c.  The new place is more logical and allows to use the
static helpers in signal.c (see the next changes).

While at it, make them return void and remove the valid_signal() check.
Nobody checks the returned value, and in-kernel users must not pass the
wrong signal number.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: cleanup the usage of t/current in do_sigaction()

The usage of "task_struct *t" and "current" in do_sigaction() looks really
annoying and chaotic.  Initially "t" is used as a cached value of current
but not consistently, then it is reused as a loop variable and we have to
use "current" again.

Clean up this mess and also convert the code to use for_each_thread().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: rename rm_from_queue_full() to flush_sigqueue_mask()

"rm_from_queue_full" looks ugly and misleading, especially now that
rm_from_queue() has gone away.  Rename it to flush_sigqueue_mask(), this
matches flush_sigqueue() we already have.

Also remove the obsolete comment which explains the difference with
rm_from_queue() we already killed.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: kill rm_from_queue(), change prepare_signal() to use for_each_thread()

rm_from_queue() doesn't make sense.  The only caller, prepare_signal(),
can use rm_from_queue_full() with the same effect.

While at it, change prepare_signal() to use for_each_thread() instead of
do/while_each_thread.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: s/siginitset/sigemptyset/ in do_sigtimedwait()

Cosmetic, but siginitset(0) looks a bit strange, sigemptyset() is what
do_sigtimedwait() needs.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

signals: kill sigfindinword()

It has no users and it doesn't look useful.  I do not know why/when it was
introduced, I can't even find any user in the git history.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: task_clear_jobctl_trapping()->wake_up_bit() needs mb()

__wake_up_bit() checks waitqueue_active() and thus the caller needs mb()
as wake_up_bit() documents, fix task_clear_jobctl_trapping().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ptrace: fix fork event messages across pid namespaces

When tracing a process in another pid namespace, it's important for fork
event messages to contain the child's pid as seen from the tracer's pid
namespace, not the parent's.  Otherwise, the tracer won't be able to
correlate the fork event with later SIGTRAP signals it receives from the
child.

We still risk a race condition if a ptracer from a different pid
namespace attaches after we compute the pid_t value.  However, sending a
bogus fork event message in this unlikely scenario is still a vast
improvement over the status quo where we always send bogus fork event
messages to debuggers in a different pid namespace than the forking
process.

Signed-off-by: Matthew Dempsky <mdempsky@chromium.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Julien Tinnes <jln@chromium.org>
Cc: Roland McGrath <mcgrathr@chromium.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/memory-barriers.txt: fix important typo re memory barriers

Examples introducing neccesity of RMB+WMP pair reads as

        A=3 READ B
        www rrrrrr
        B=4 READ A

Note the opposite order of reads vs writes.

But the first example without barriers reads as

        A=3 READ A
        B=4 READ B

There are 4 outcomes in the first example.

But if someone new to the concept tries to insert barriers like this:

        A=3 READ A
        www rrrrrr
        B=4 READ B

he will still get all 4 possible outcomes, because "READ A" is first.

All this can be utterly confusing because barrier pair seems to be
superfluous.  In short, fixup first example to match latter examples
with barriers.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/filesystems/seq_file.txt: create_proc_entry deprecated

Linked article in seq_file.txt still uses create_proc_entry which was
removed in commit 80e928f7ebb9 ("proc: Kill create_proc_entry()").

This patch adds information for kernel 3.10 and above

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/SubmittingPatches: describe the Fixes: tag

Update the SubmittingPatches process to include howto about the new
'Fixes:' tag to be used when a patch fixes an issue in a previous commit
(found by git-bisect for example).

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/fat/inode.c: clean up string initializations (char[] instead of char *)

Initializations like 'char *foo = "bar"' will create two variables: a
static string and a pointer (foo) to that static string.  Instead 'char
foo[] = "bar"' will declare a single variable and will end up in shorter
assembly (according to Jeff Garzik on the KernelJanitor's TODO list).

Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/fat/: add support for DOS 1.x formatted volumes

Add structure for parsed BPB information, struct fat_bios_param_block,
and move all of the deserialization and validation logic from
fat_fill_super() into fat_read_bpb().

Add a 'dos1xfloppy' mount option to infer DOS 2.x BIOS Parameter Block
defaults from block device geometry for ancient floppies and floppy
images, as a fall-back from the default BPB parsing logic.

When fat_read_bpb() finds an invalid FAT filesystem and dos1xfloppy is
set, fall back to fat_read_static_bpb().  fat_read_static_bpb()
validates that the entire BPB is zero, and that the floppy has a
DOS-style 8086 code bootstrapping header.  Then it fills in default BPB
values from media size and a table.[0]

Media size is assumed to be static for archaic FAT volumes.  See also:
[1].

Fixes kernel.org bug #42617.

[0]: https://en.wikipedia.org/wiki/File_Allocation_Table#Exceptions
[1]: http://www.win.tue.nl/~aeb/linux/fs/fat/fat-1.html

[hirofumi@mail.parknet.co.jp: fix missed error code]
Signed-off-by: Conrad Meyer <cse.cem@gmail.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hpfs: increase pr_warn level

This patch applies a suggestion by Mikulas Patocka asking to increase
all pr_warn without commented ones to pr_err

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hpfs: use __func__ for logging

Normalize function display fx() using __func__

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hpfs: use pr_fmt for logging

Also remove redundant level names (warning:...)

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hpfs: convert printk to pr_foo()

No level printk in hptfs_error converted to pr_err (others to pr_warn or
pr_info)

This patch also fixes if/then/else checkpatch warnings

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/ufs/balloc.c: remove err parameter in ufs_add_fragments

err is used in ufs_new_fragments (ufs_add_fragments only callsite)
not in ufs_add_fragments.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: fix compiler warning on PowerPC

Commit a99b7069aab8 ("hfsplus: Fix undefined __divdi3 in
hfsplus_init_header_node()") introduced do_div() to xattr.c and the
warning below too.

As Geert remarked: "tmp" is "loff_t" which is "__kernel_loff_t", which
is "long long", i.e.  signed, while include/asm-generic/div64.h compares
its type with "uint64_t".  As inode sizes are positive, it should be
safe to change the type of "tmp" to "u64".

  In file included from
  arch/powerpc/include/asm/div64.h:1:0,
                    from include/linux/kernel.h:124,
                    from include/asm-generic/bug.h:13,
                    from arch/powerpc/include/asm/bug.h:127,
                    from include/linux/bug.h:4,
                    from include/linux/thread_info.h:11,
                    from include/asm-generic/preempt.h:4,
                    from arch/powerpc/include/generated/asm/preempt.h:1,
                    from include/linux/preempt.h:18,
                    from include/linux/spinlock.h:50,
                    from include/linux/wait.h:8,
                    from include/linux/fs.h:6,
                    from fs/hfsplus/hfsplus_fs.h:19,
                    from fs/hfsplus/xattr.c:9:
  fs/hfsplus/xattr.c: In function 'hfsplus_init_header_node':
  include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast [enabled by default]
     (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
                               ^
  fs/hfsplus/xattr.c:86:2: note: in expansion of macro 'do_div'
     do_div(tmp, node_size);
     ^

Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hfsplus: fix pr_foo() and hfs_dbg formats

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Suggested-By: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: coding style fix for declarations in hfsplus_fs.h

Some function declarations in hfsplus_fs.h were with argument names,
some without, and some were mixed.  This patch adds argument names
everywhere, sorts function in order they go in .c files, and moves
hfs_part_find() to a proper section.

Auto-formatting and sorting was done with:
cfunctions *.c | indent -linux | sed "s| \* | \*|"

Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hfsplus/wrapper.c: replace shift loop by ilog2

Replace while blocksize;shift by ilog2

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: fix "unused node is not erased" error

Zero newly allocated extents in the catalog tree if volume attributes
tell us to.  Not doing so we risk getting the "unused node is not
erased" error.  See kHFSUnusedNodeFix flag in Apple's source code for
reference.

There was a previous commit clearing the node when it is freed: commit
899bed05e9f6 ("hfsplus: fix issue with unzeroed unused b-tree nodes").
But it did not handle newly allocated extents (this patch fixes it).
And it zeroed nodes in all trees unconditionally which is an overkill.

This patch adds a condition and also switches to 'tree->node_size' as a
simpler method of getting the length to zero.

Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Anton Altaparmakov <aia21@cam.ac.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Kyle Laracey <kalaracey@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hfsplus/wrapper.c: replace min/casting by min_t

Also add * before function comments (it was not detected by kernel-doc)

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hfsplus/options.c: replace seq_printf by seq_puts

Replace seq_printf where possible

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/hfsplus/bnode.c: replace min/casting by min_t

Also fixes some pr_ formats

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: emit proper file type from readdir

hfsplus_readdir() incorrectly returned DT_REG for symbolic links and
special files.  Return DT_REG, DT_LNK, DT_FIFO, DT_CHR, DT_BLK, DT_SOCK,
or DT_UNKNOWN according to mode field in catalog record.  Programs
relying on information from readdir will now work correctly with HFS+.

Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Anton Altaparmakov <aia21@cam.ac.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: remove unused routine hfsplus_attr_build_key_uni

The directory/file catalog b-tree equivalent, hfsplus_build_key_uni(),
is used by hfsplus_find_cat() for internal referencing between catalog
records.  There is no corresponding usage for attributes - attribute
records do not refer to one another.

Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Sougata Santra <sougata@tuxera.com>
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: correct usage of HFSPLUS_ATTR_MAX_STRLEN for non-English attributes

HFSPLUS_ATTR_MAX_STRLEN (=127) is the limit of attribute names for the
number of unicode character (UTF-16BE) storable in the HFS+ file system.
Almost all the current usage of it is wrong, in relation to NLS to
on-disk conversion.

Except for one use calling hfsplus_asc2uni (which should stay the same)
and its uses in calling hfsplus_uni2asc (which was corrected in the
earlier patch in this series concerning usage of hfsplus_uni2asc), all
the other uses are of the forms:

- char buffer[size]

- bound check: "if (namespace_adjusted_input_length > size) return failure;"

Conversion between on-disk unicode representation and NLS char strings
(in whichever direction) always needs to accommodate the worst-case NLS
conversion, so all char buffers of that size need to have a
NLS_MAX_CHARSET_SIZE x .

The bound checks are all wrong, since they compare nls_length derived
from strlen() to a unicode length limit.

It turns out that all the bound-checks do is to protect
hfsplus_asc2uni(), which can fail if the input is too large.

There is only one usage of it as far as attributes are concerned, in
hfsplus_attr_build_key().  It is in turn used by hfsplus_find_attr(),
hfsplus_create_attr(), hfsplus_delete_attr().  Thus making sure that
errors from hfsplus_asc2uni() is caught in hfsplus_attr_build_key() and
propagated is sufficient to replace all the bound checks.

Unpropagated errors from hfsplus_asc2uni() in the file catalog code was
addressed recently in an independent patch "hfsplus: fix longname
handling" by Sougata Santra.

Before this patch, trying to set a 55 CJK character (in a UTF-8 locale,
> 127/3=42) attribute plus user prefix fails with:

    $ setfattr -n user.`cat testing-string` -v `cat testing-string` \
        testing-string
    setfattr: testing-string: Operation not supported

and retrieving a stored long attributes is particular ugly(!):

    find /mnt/* -type f -exec getfattr -d {} \;
    getfattr: /mnt/testing-string: Input/output error

with console log:
    [268008.389781] hfsplus: unicode conversion failed

After the patch, both of the above works.

FYI, the test attribute string is prepared with:

echo -e -n \
"\xe9\x80\x99\xe6\x98\xaf\xe4\xb8\x80\xe5\x80\x8b\xe9\x9d\x9e\xe5" \
"\xb8\xb8\xe6\xbc\xab\xe9\x95\xb7\xe8\x80\x8c\xe6\xa5\xb5\xe5\x85" \
"\xb6\xe4\xb9\x8f\xe5\x91\xb3\xe5\x92\x8c\xe7\x9b\xb8\xe7\x95\xb6" \
"\xe7\x84\xa1\xe8\xb6\xa3\xe3\x80\x81\xe4\xbb\xa5\xe5\x8f\x8a\xe7" \
"\x84\xa1\xe7\x94\xa8\xe7\x9a\x84\xe3\x80\x81\xe5\x86\x8d\xe5\x8a" \
"\xa0\xe4\xb8\x8a\xe6\xaf\xab\xe7\x84\xa1\xe6\x84\x8f\xe7\xbe\xa9" \
"\xe7\x9a\x84\xe6\x93\xb4\xe5\xb1\x95\xe5\xb1\xac\xe6\x80\xa7\xef" \
"\xbc\x8c\xe8\x80\x8c\xe5\x85\xb6\xe5\x94\xaf\xe4\xb8\x80\xe5\x89" \
"\xb5\xe5\xbb\xba\xe7\x9b\xae\xe7\x9a\x84\xe5\x83\x85\xe6\x98\xaf" \
"\xe7\x82\xba\xe4\xba\x86\xe6\xb8\xac\xe8\xa9\xa6\xe4\xbd\x9c\xe7" \
"\x94\xa8\xe3\x80\x82" | tr -d ' '

(= "pointlessly long attribute for testing", elaborate Chinese in
UTF-8 enoding).

However, it is not possible to set double the size (110 + 5 is still
under 127) in a UTF-8 locale:

    $setfattr -n user.`cat testing-string testing-string` -v \
        `cat testing-string testing-string` testing-string
    setfattr: testing-string: Numerical result out of range

110 CJK char in UTF-8 is 330 bytes - the generic get/set attribute
system call code in linux/fs/xattr.c imposes a 255 byte limit.  One can
use a combination of iconv to encode content, changing terminal locale
for viewing, and an nls=cp932/cp936/cp949/cp950 mount option to fully
use 127-unicode attribute in a double-byte locale.

Also, as an additional information, it is possible to (mis-)use unicode
half-width/full-width forms (U+FFxx) to write attributes which looks
like english but not actually ascii.

Thanks Anton Altaparmakov for reviewing the earlier ideas behind this
change.

[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix build]
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Sougata Santra <sougata@tuxera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: fix worst-case unicode to char conversion of file names and attributes

This is a series of 3 patches which corrects issues in HFS+ concerning
the use of non-english file names and attributes.  Names and attributes
are stored internally as UTF-16 units up to a fixed maximum size, and
convert to and from user-representation by NLS.  The code incorrectly
assume that NLS string lengths are equal to unicode lengths, which is
only true for English ascii usage.

This patch (of 3):

The HFS Plus Volume Format specification (TN1150) states that file names
are stored internally as a maximum of 255 unicode characters, as defined
by The Unicode Standard, Version 2.0 [Unicode, Inc.  ISBN
0-201-48345-9].  File names are converted by the NLS system on Linux
before presented to the user.

255 CJK characters converts to UTF-8 with 1 unicode character to up to 3
bytes, and to GB18030 with 1 unicode character to up to 4 bytes.  Thus,
trying in a UTF-8 locale to list files with names of more than 85 CJK
characters results in:

    $ ls /mnt
    ls: reading directory /mnt: File name too long

The receiving buffer to hfsplus_uni2asc() needs to be 255 x
NLS_MAX_CHARSET_SIZE bytes, not 255 bytes as the code has always been.

Similar consideration applies to attributes, which are stored internally
as a maximum of 127 UTF-16BE units.  See XNU source for an up-to-date
reference on attributes.

Strictly speaking, the maximum value of NLS_MAX_CHARSET_SIZE = 6 is not
attainable in the case of conversion to UTF-8, as going beyond 3 bytes
requires the use of surrogate pairs, i.e.  consuming two input units.

Thanks Anton Altaparmakov for reviewing an earlier version of this
change.

This patch fixes all callers of hfsplus_uni2asc(), and also enables the
use of long non-English file names in HFS+.  The getting and setting,
and general usage of long non-English attributes requires further
forthcoming work, in the following patches of this series.

[akpm@linux-foundation.org: fix build]
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Reviewed-by: Anton Altaparmakov <anton@tuxera.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Sougata Santra <sougata@tuxera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/coda: use __func__

Replace all function names by __func__ in pr_foo()

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Jan Harkes <jaharkes@cs.cmu.edu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/coda: logging prefix uniformization

- Add pr_fmt based on module name.

- Remove Coda: coda: from pr_foo()

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Jan Harkes <jaharkes@cs.cmu.edu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/coda: replace printk by pr_foo()

No level printk converted to pr_warn or pr_info

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Jan Harkes <jaharkes@cs.cmu.edu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/befs: kernel-doc fixes

Fix some comment errors.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/befs/linuxvfs.c: remove positive test on sector_t

sector_t is unsigned.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/befs/btree.c: replace strncpy by strlcpy + coding style fixing

- strncpy + end of string assignement replaced by strlcpy

- Fix endif };

- Fix typo

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/befs/linuxvfs.c: replace strncpy by strlcpy

strncpy + end of string assignment replaced by strlcpy

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-pxa.c: make of_device_id array const

Make of_device_id array const, because all OF functions handle
it as const.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-sa1100.c: make of_device_id array const

Make of_device_id array const, because all OF functions handle
it as const.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-omap.c: enable RTC_IRQWAKEEN bits when Alarm is set

When RTC CLKTRCTRL bit is configured in HW_AUTO, module goes to sleep in
IDLE state.

The Alarm SWakeup event can be used to wakeup the RTC when it is in IDLE
state.  In order to do so, the alarm needs to be set and enabled before
RTC enters the IDLE state.  Also the wakeup generation for alarm/timer
event needs to be set (bits [1:0] in RTC_IRQWAKEEN register).

Currently RTC_IRQWAKEEN bits are set only in suspend/resume paths.  With
this ALARM interrupts are not generated when it enters IDLE state.  So
programming the RTC_IRQWAKEEN bits when ever ALARM is set.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ARM: at91: fix at91_sysirq_mask_rtc for sam9x5 SoCs

sam9x5 SoCs have the following errata:
 "RTC: Interrupt Mask Register cannot be used
  Interrupt Mask Register read always returns 0."

Hence we should not rely on what IMR claims about already masked IRQs
and just disable all IRQs.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Bryan Evenson <bevenson@melinkcorp.com>
Reviewed-by: Johan Hovold <johan@hovold.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Bryan Evenson <bevenson@melinkcorp.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Roszko <mark.roszko@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-at91rm9200: fix infinite wait for ACKUPD irq

The rtc user must wait at least 1 sec between each time/calandar update
(see atmel's datasheet chapter "Updating Time/Calendar").

Use the 1Hz interrupt to update the at91_rtc_upd_rdy flag and wait for
the at91_rtc_wait_upd_rdy event if the rtc is not ready.

This patch fixes a deadlock in an uninterruptible wait when the RTC is
updated more than once every second.  AFAICT the bug is here from the
beginning, but I think we should at least backport this fix to 3.10 and
the following longterm and stable releases.

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Bryan Evenson <bevenson@melinkcorp.com>
Tested-by: Bryan Evenson <bevenson@melinkcorp.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-hym8563.c: add optional clock-output-names property

This enables the setting of a custom clock name for the clock provided by
the hym8563 rtc.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-bfin.c: do not abort when requesting irq fails

The RTC framework does not let you return an error once a call to
devm_rtc_device_register has succeeded.  Avoid doing that when the IRQ
request fails as we can still support reading/writing the clock without
the IRQ.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reported-by: Ales Novak <alnovak@suse.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-omap.c: add support for enabling 32khz clock

Newer versions of OMAP RTC IP such as those found in AM335x and DRA7x
need an explicit enable of 32khz functional clock which ticks the RTC.

AM335x support was working so far because of settings done in U-Boot.
However, the DRA7x U-Boot does no such enable of 32khz clock and this
patch is need to get the RTC to work on DRA7x at least.  In general, it
is better to not depend on settings done in U-Boot.

Thanks to Lokesh Vutla for noticing this.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-omap.c: use BIT() macro

Use BIT() macro for RTC_HAS_<FEATURE> defines instead of hand-writing
bit masks.

Use BIT() macros for register bit field definitions.

While at it, fix indentation done using spaces.

No functional change in this patch.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-omap.c: remove multiple device id checks

Remove multiple superfluous device id checks.  Since an id_table is
present in the driver probe() should never encounter an empty device id
entry.  In case of OF style match, of_match_device() returns an matching
entry.

For paranoia sake, check for device id entry once and fail probe() if none
is found.  This is much better than checking for it multiple times.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: da9063: RTC driver

Add the RTC driver for DA9063.

[akpm@linux-foundation.org: coding-style tweaks]
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Mark Brown <broonie@linaro.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc: add support for Microchip MCP795

Add driver for SPI RTC Microchip MCP795.  Only supports saving/loading
time from the chip (i.  e.  no alarms/power events/ID).

Signed-off-by: Josef Gajdusek <atx@atx.name>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/rtc/rtc-ds1343.c: fix potential race condition

Avoid the potential race condition by avoiding bailing out of driver in
probe after registering with rtc subsystem

Also the set_alarm , read_alarm and alarm_irq_enable returns error if irq
registration fails in probe.

Also the sysfs will not create entry for alarm if irq registration fails
in probe.

Signed-off-by: Raghavendra Chandra Ganiga <ravi23ganiga@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>