mt76x2: fix tx power configuration for VHT mcs 9

[ Upstream commit 60b6645ef1a9239a02c70adeae136298395d145a ]

Fix tx power configuration for VHT 1SS/STBC mcs 9 since
in MT_TX_PWR_CFG_{8,9} mcs 8,9 bits are GENMASK(21,16) and
GENMASK(29,24) while GENMASK(15,6) are marked as reserved

Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/hfi1: Ensure ucast_dlid access doesnt exceed bounds

[ Upstream commit 3144533bf667c8e53bb20656b78295960073e57b ]

The dlid assignment made by looking into the u_ucast_dlid array does not
do an explicit check for the size of the array. The code path to arrive at
def_port, the index value is long and complicated so its best to just have
an explicit check here.

Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/hfi1: Error path MAD response size is incorrect

[ Upstream commit 935c84ac649a147e1aad2c48ee5c5a1a9176b2d0 ]

If a MAD packet has incorrect header information, the logic uses the reply
path to report the error.  The reply path expects *resp_len to be set
prior to return.  Unfortunately, *resp_len is set to 0 for this path.
This causes an incorrect response packet.

Fix by ensuring that the *resp_len is defaulted to the incoming packet
size (wc->bytes_len - sizeof(GRH)).

Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: keep lazytime on remount

[ Upstream commit 095680f24f2673d860fd1d3d2f54f40f330b4c63 ]

This patch fixes losing lazytime when remounting f2fs.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI / LPSS: Resume BYT/CHT I2C controllers from resume_noirq

[ Upstream commit 48402cee6889fb3fce58e95fea1471626286dc63 ]

On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over a LPSS I2C controller.

We add a device-link to make sure that the I2C controller is resumed before
the GPU is. But the pci-core changes the power-state of PCI devices from
D3 to D0 at noirq time (to restore the PCI config registers) and before
this commit we were bringing up the I2C controllers from a resume_early
handler which runs later. More specifically the pm-core will first run
all resume_noirq handlers in order and then all resume_early handlers.

So we must not only make sure that the handlers are run in the right order,
but also that the resume of the I2C controller is done at noirq time.

The behavior before this commit, resuming the I2C controller from a
resume_early handler leads to the following errors:

 i2c_designware 808622C1:06: controller timed out
 ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
 ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
 video LNXVIDEO:00: Failed to change power state to D0

This commit changes the acpi_lpss.c code to resume the BYT/CHT I2C
controllers at resume_noirq time fixing this.

Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI / LPSS: Make acpi_lpss_find_device() also find PCI devices

[ Upstream commit 1e30124ac60abc41d74793900f8b4034f29bcb3d ]

On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over one of the LPSS I2C controllers.

To get the suspend/resume ordering correct for this we need to be able to
add device-links between the GPU and the I2c controller. The GPU is a PCI
device, so this requires acpi_lpss_find_device() to also work on PCI devs.

Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

SUNRPC: Fix priority queue fairness

[ Upstream commit f42f7c283078ce3c1e8368b140e270755b1ae313 ]

Fix up the priority queue to not batch by owner, but by queue, so that
we allow '1 << priority' elements to be dequeued before switching to
the next priority queue.
The owner field is still used to wake up requests in round robin order
by owner to avoid single processes hogging the RPC layer by loading the
queues.

Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: up initial rmem to 128KB and SYN rwin to around 64KB

[ Upstream commit a337531b942bd8a03e7052444d7e36972aac2d92 ]

Previously TCP initial receive buffer is ~87KB by default and
the initial receive window is ~29KB (20 MSS). This patch changes
the two numbers to 128KB and ~64KB (rounding down to the multiples
of MSS) respectively. The patch also simplifies the calculations s.t.
the two numbers are directly controlled by sysctl tcp_rmem[1]:

  1) Initial receiver buffer budget (sk_rcvbuf): while this should
     be configured via sysctl tcp_rmem[1], previously tcp_fixup_rcvbuf()
     always override and set a larger size when a new connection
     establishes.

  2) Initial receive window in SYN: previously it is set to 20
     packets if MSS <= 1460. The number 20 was based on the initial
     congestion window of 10: the receiver needs twice amount to
     avoid being limited by the receive window upon out-of-order
     delivery in the first window burst. But since this only
     applies if the receiving MSS <= 1460, connection using large MTU
     (e.g. to utilize receiver zero-copy) may be limited by the
     receive window.

With this patch TCP memory configuration is more straight-forward and
more properly sized to modern high-speed networks by default. Several
popular stacks have been announcing 64KB rwin in SYNs as well.

Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: sun8i: h3: bpi-m2-plus: Fix address for external RGMII Ethernet PHY

[ Upstream commit db9fd9d13e30fc67737ac9893a82e6b095e85a64 ]

The external RTL8211E RGMII Ethernet PHY is configured via external
resistors to use the address 0x1. The 0x0 address is a broadcast address
for this family of PHYs, and should not be used explicitly.

Fixes: 8c7ba536e709 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: sun8i: h3-h5: ir register size should be the whole memory block

[ Upstream commit 6c700289a3e84d5d3f2a95cf27732a7f7fce105b ]

The size of the register should be the size of the whole memory block,
not just the registers, that are needed.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: return correct errno in f2fs_gc

[ Upstream commit 61f7725aa148ee870436a29d3a24d5c00ab7e9af ]

This fixes overriding error number in f2fs_gc.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: Fix loss of coal configuration while doing reset

[ Upstream commit e4fd75022c24eb28cc1034e97e60cecc24f325f3 ]

The user's coal configuration will be lost after reset, so the tx_coal
and rx_coal fields are added to the struct hns_nic_priv to save the coal
configuration and used to restore the user's configuration after the reset
is complete.

Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: Fix for netdev not up problem when setting mtu

[ Upstream commit 93d8daf460183871a965dae339839d9e35d44309 ]

Currently hns3_nic_change_mtu will try to down the netdev before
setting mtu, and it does not up the netdev when the setting fails,
which causes netdev not up problem.

This patch fixes it by not returning when the setting fails.

Fixes: a8e8b7ff3517 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: omap5: enable OTG role for DWC3 controller

[ Upstream commit 656c1a65ab555ee5c7cd0d6aee8ab82ca3c1795f ]

Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).

Tested on OMAP5EVM and Pyra.

Suggested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: dra7: Enable workaround for errata i870 in PCIe host mode

[ Upstream commit b830526f304764753fcb8b4a563a94080e982a6c ]

Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: xen-netback: fix return type of ndo_start_xmit function

[ Upstream commit a9ca7f17c6d240e269a24cbcd76abf9a940309dd ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ovs: fix return type of ndo_start_xmit function

[ Upstream commit eddf11e18dff0e8671e06ce54e64cfc843303ab9 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, x32: Fix bug for BPF_JMP | {BPF_JSGT, BPF_JSLE, BPF_JSLT, BPF_JSGE}

commit 711aef1bbf88212a21f7103e88f397b47a528805 upstream.

The current method to compare 64-bit numbers for conditional jump is:

1) Compare the high 32-bit first.

2) If the high 32-bit isn't the same, then goto step 4.

3) Compare the low 32-bit.

4) Check the desired condition.

This method is right for unsigned comparison, but it is buggy for signed
comparison, because it does signed comparison for low 32-bit too.

There is only one sign bit in 64-bit number, that is the MSB in the 64-bit
number, it is wrong to treat low 32-bit as signed number and do the signed
comparison for it.

This patch fixes the bug and adds a testcase in selftests/bpf for such bug.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=205469
Reported-by: Tony Ambardar <itugrok@yahoo.com>
Cc: Tony Ambardar <itugrok@yahoo.com>
Cc: stable@vger.kernel.org #v4.19
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf, x32: Fix bug with ALU64 {LSH, RSH, ARSH} BPF_K shift by 0

commit 6fa632e719eec4d1b1ebf3ddc0b2d667997b057b upstream.

The current x32 BPF JIT does not correctly compile shift operations when
the immediate shift amount is 0. The expected behavior is for this to
be a no-op.

The following program demonstrates the bug. The expexceted result is 1,
but the current JITed code returns 2.

  r0 = 1
  r1 = 1
  r1 <<= 0
  if r1 == 1 goto end
  r0 = 2
end:
  exit

This patch simplifies the code and fixes the bug.

Fixes: 03f5781be2c7 ("bpf, x86_32: add eBPF JIT compiler for ia32")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf, x32: Fix bug with ALU64 {LSH, RSH, ARSH} BPF_X shift by 0

commit 68a8357ec15bdce55266e9fba8b8b3b8143fa7d2 upstream.

The current x32 BPF JIT for shift operations is not correct when the
shift amount in a register is 0. The expected behavior is a no-op, whereas
the current implementation changes bits in the destination register.

The following example demonstrates the bug. The expected result of this
program is 1, but the current JITed code returns 2.

  r0 = 1
  r1 = 1
  r2 = 0
  r1 <<= r2
  if r1 == 1 goto end
  r0 = 2
end:
  exit

The bug is caused by an incorrect assumption by the JIT that a shift by
32 clear the register. On x32 however, shifts use the lower 5 bits of
the source, making a shift by 32 equivalent to a shift by 0.

This patch fixes the bug using double-precision shifts, which also
simplifies the code.

Fixes: 03f5781be2c7 ("bpf, x86_32: add eBPF JIT compiler for ia32")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf, x32: Fix bug for BPF_ALU64 | BPF_NEG

commit b9aa0b35d878dff9ed19f94101fe353a4de00cc4 upstream.

The current implementation has two errors:

1: The second xor instruction will clear carry flag which
   is necessary for following sbb instruction.
2: The select coding for sbb instruction is wrong, the coding
   is "sbb dreg_hi,ecx", but what we need is "sbb ecx,dreg_hi".

This patch rewrites the implementation and fixes the errors.

This patch fixes below errors reported by bpf/test_verifier in x32
platform when the jit is enabled:

"
0: (b4) w1 = 4
1: (b4) w2 = 4
2: (1f) r2 -= r1
3: (4f) r2 |= r1
4: (87) r2 = -r2
5: (c7) r2 s>>= 63
6: (5f) r1 &= r2
7: (bf) r0 = r1
8: (95) exit
processed 9 insns (limit 131072), stack depth 0
0: (b4) w1 = 4
1: (b4) w2 = 4
2: (1f) r2 -= r1
3: (4f) r2 |= r1
4: (87) r2 = -r2
5: (c7) r2 s>>= 63
6: (5f) r1 &= r2
7: (bf) r0 = r1
8: (95) exit
processed 9 insns (limit 131072), stack depth 0
......
Summary: 1189 PASSED, 125 SKIPPED, 15 FAILED
"

Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: Ditch fb_edid_add_monspecs

commit 3b8720e63f4a1fc6f422a49ecbaa3b59c86d5aaf upstream.

It's dead code ever since

commit 34280340b1dc74c521e636f45cd728f9abf56ee2
Author: Geert Uytterhoeven <geert+renesas@glider.be>
Date:   Fri Dec 4 17:01:43 2015 +0100

    fbdev: Remove unused SH-Mobile HDMI driver

Also with this gone we can remove the cea_modes db. This entire thing
is massively incomplete anyway, compared to the CEA parsing that
drm_edid.c does.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tavis Ormandy <taviso@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190721201956.941-1-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: uaccess: Ensure PAN is re-enabled after unhandled uaccess fault

commit 94bb804e1e6f0a9a77acf20d7c70ea141c6c821e upstream.

A number of our uaccess routines ('__arch_clear_user()' and
'__arch_copy_{in,from,to}_user()') fail to re-enable PAN if they
encounter an unhandled fault whilst accessing userspace.

For CPUs implementing both hardware PAN and UAO, this bug has no effect
when both extensions are in use by the kernel.

For CPUs implementing hardware PAN but not UAO, this means that a kernel
using hardware PAN may execute portions of code with PAN inadvertently
disabled, opening us up to potential security vulnerabilities that rely
on userspace access from within the kernel which would usually be
prevented by this mechanism. In other words, parts of the kernel run the
same way as they would on a CPU without PAN implemented/emulated at all.

For CPUs not implementing hardware PAN and instead relying on software
emulation via 'CONFIG_ARM64_SW_TTBR0_PAN=y', the impact is unfortunately
much worse. Calling 'schedule()' with software PAN disabled means that
the next task will execute in the kernel using the page-table and ASID
of the previous process even after 'switch_mm()', since the actual
hardware switch is deferred until return to userspace. At this point, or
if there is a intermediate call to 'uaccess_enable()', the page-table
and ASID of the new process are installed. Sadly, due to the changes
introduced by KPTI, this is not an atomic operation and there is a very
small window (two instructions) where the CPU is configured with the
page-table of the old task and the ASID of the new task; a speculative
access in this state is disastrous because it would corrupt the TLB
entries for the new task with mappings from the previous address space.

As Pavel explains:

  | I was able to reproduce memory corruption problem on Broadcom's SoC
  | ARMv8-A like this:
  |
  | Enable software perf-events with PERF_SAMPLE_CALLCHAIN so userland's
  | stack is accessed and copied.
  |
  | The test program performed the following on every CPU and forking
  | many processes:
  |
  | unsigned long *map = mmap(NULL, PAGE_SIZE, PROT_READ|PROT_WRITE,
  |   MAP_SHARED | MAP_ANONYMOUS, -1, 0);
  | map[0] = getpid();
  | sched_yield();
  | if (map[0] != getpid()) {
  | fprintf(stderr, "Corruption detected!");
  | }
  | munmap(map, PAGE_SIZE);
  |
  | From time to time I was getting map[0] to contain pid for a
  | different process.

Ensure that PAN is re-enabled when returning after an unhandled user
fault from our uaccess routines.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 338d4f49d6f7 ("arm64: kernel: Add support for Privileged Access Never")
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: rewrote commit message]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/memory_hotplug: fix updating the node span

commit 656d571193262a11c2daa4012e53e4d645bbce56 upstream.

We recently started updating the node span based on the zone span to
avoid touching uninitialized memmaps.

Currently, we will always detect the node span to start at 0, meaning a
node can easily span too many pages.  pgdat_is_empty() will still work
correctly if all zones span no pages.  We should skip over all zones
without spanned pages and properly handle the first detected zone that
spans pages.

Unfortunately, in contrast to the zone span (/proc/zoneinfo), the node
span cannot easily be inspected and tested.  The node span gives no real
guarantees when an architecture supports memory hotplug, meaning it can
easily contain holes or span pages of different nodes.

The node span is not really used after init on architectures that
support memory hotplug.

E.g., we use it in mm/memory_hotplug.c:try_offline_node() and in
mm/kmemleak.c:kmemleak_scan().  These users seem to be fine.

Link: http://lkml.kernel.org/r/20191027222714.5313-1-david@redhat.com
Fixes: 00d6c019b5bc ("mm/memory_hotplug: don't access uninitialized memmaps in shrink_pgdat_span()")
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/memory_hotplug: don't access uninitialized memmaps in shrink_pgdat_span()

commit 00d6c019b5bc175cee3770e0e659f2b5f4804ea5 upstream.

We might use the nid of memmaps that were never initialized.  For
example, if the memmap was poisoned, we will crash the kernel in
pfn_to_nid() right now.  Let's use the calculated boundaries of the
separate zones instead.  This now also avoids having to iterate over a
whole bunch of subsections again, after shrinking one zone.

Before commit d0dc12e86b31 ("mm/memory_hotplug: optimize memory
hotplug"), the memmap was initialized to 0 and the node was set to the
right value.  After that commit, the node might be garbage.

We'll have to fix shrink_zone_span() next.

Link: http://lkml.kernel.org/r/20191006085646.5768-4-david@redhat.com
Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [d0dc12e86b319]
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Damian Tometzki <damian.tometzki@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jun Yao <yaojun8558363@gmail.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Pankaj Gupta <pagupta@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Rich Felker <dalias@libc.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Yu Zhao <yuzhao@google.com>
Cc: <stable@vger.kernel.org> [4.13+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

idr: Fix idr_get_next race with idr_remove

commit 5c089fd0c73411f2170ab795c9ffc16718c7d007 upstream.

If the entry is deleted from the IDR between the call to
radix_tree_iter_find() and rcu_dereference_raw(), idr_get_next()
will return NULL, which will end the iteration prematurely.  We should
instead continue to the next entry in the IDR.  This only happens if the
iteration is protected by the RCU lock.  Most IDR users use a spinlock
or semaphore to exclude simultaneous modifications.  It was noticed once
the PID allocator was converted to use the IDR, as it uses the RCU lock,
but there may be other users elsewhere in the kernel.

We can't use the normal pattern of calling radix_tree_deref_retry()
(which catches both a retry entry in a leaf node and a node entry in
the root) as the IDR supports storing entries which are unaligned,
which will trigger an infinite loop if they are encountered.  Instead,
we have to explicitly check whether the entry is a retry entry.

Fixes: 0a835c4f090a ("Reimplement IDR and IDA using the radix tree")
Reported-by: Brendan Gregg <bgregg@netflix.com>
Tested-by: Brendan Gregg <bgregg@netflix.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: cdc_ncm: Signedness bug in cdc_ncm_set_dgram_size()

commit a56dcc6b455830776899ce3686735f1172e12243 upstream.

This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.

Fixes: 332f989a3b00 ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "OPP: Protect dev_list with opp_table lock"

This reverts commit 4c64ce947cfa447993efe005cbaad7ba31a91612 which is
commit 3d2556992a878a2210d3be498416aee39e0c32aa upstream.

Turns out to break the build on the odroid machines, so it needs to be
reverted.

Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tee: optee: add missing of_node_put after of_device_is_available

commit c7c0d8df0b94a67377555a550b8d66ee2ad2f4ed upstream.

Add an of_node_put when a tested device node is not available.

The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@@
identifier f;
local idexpression e;
expression x;
@@

e = f(...);
... when != of_node_put(e)
    when != x = e
    when != e = x
    when any
if (<+...of_device_is_available(e)...+>) {
  ... when != of_node_put(e)
(
  return e;
|
+ of_node_put(e);
  return ...;
)
}
// </smpl>

Fixes: db878f76b9ff ("tee: optee: take DT status property into account")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: mediatek: modify threshold passed to i2c_get_dma_safe_msg_buf()

commit bc1a7f75c85e226e82f183d30d75c357f92b6029 upstream.

DMA with zero-length transfers doesn't make sense and this HW doesn't
support them at all, so increase the threshold.

Fixes: fc66b39fe36a ("i2c: mediatek: Use DMA safe buffers for i2c transactions")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: mediatek: use correct mata->xfer_len when in fifo transfer

commit a4d8f64f7267a88d4688f5c216926f5f6cafbae6 upstream.

when xfer_len is greater than 64 bytes and use fifo mode
to transfer, the actual length from the third time is mata->xfer_len
but not len in mtk_spi_interrupt().

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.19.85

slcan: Fix memory leak in error path

commit ed50e1600b4483c049ce76e6bd3b665a6a9300ed upstream.

This patch is fixing memory leak reported by Syzkaller:

BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096):
  comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s)
  hex dump (first 32 bytes):
    73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0..........
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
  backtrace:
    [<00000000a06eec0d>] __kmalloc+0x18b/0x2c0
    [<0000000083306e66>] kvmalloc_node+0x3a/0xc0
    [<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080
    [<0000000061a996c9>] slcan_open+0x3ae/0x9a0
    [<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0
    [<0000000019289631>] tty_set_ldisc+0x28c/0x5f0
    [<000000004de5a617>] tty_ioctl+0x48d/0x1590
    [<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510
    [<0000000059068dbc>] ksys_ioctl+0x99/0xb0
    [<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0
    [<0000000053d0332e>] do_syscall_64+0x16f/0x580
    [<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
    [<000000008ea75434>] 0xffffffffffffffff

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memfd: Use radix_tree_deref_slot_protected to avoid the warning.

The commit 99b45e7a1ba1 ("memfd: Fix locking when tagging pins")
introduces the following warning messages.

*WARNING: suspicious RCU usage in memfd_wait_for_pins*

It is because we still use radix_tree_deref_slot without read_rcu_lock.
We should use radix_tree_deref_slot_protected instead in the case.

Cc: stable@vger.kernel.org
Fixes: 99b45e7a1ba1 ("memfd: Fix locking when tagging pins")
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: mdio-bcm-unimac: mark PM functions as __maybe_unused

[ Upstream commit 9b97123a584f60a5bca5a2663485768a1f6cd0a4 ]

The newly added runtime-pm support causes a harmless warning
when CONFIG_PM is disabled:

drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function]
 static int unimac_mdio_resume(struct device *d)
drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function]
 static int unimac_mdio_suspend(struct device *d)

Marking the functions as __maybe_unused is the easiest workaround
and avoids adding #ifdef checks.

Fixes: b78ac6ecd1b6 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/vdso: correct vdso mapping for compat tasks

[ Upstream commit 190f056fba230abee80712eb810939ef9a8c462f ]

While "s390/vdso: avoid 64-bit vdso mapping for compat tasks" fixed
64-bit vdso mapping for compat tasks under gdb it introduced another
problem. "compat_mm" flag is not inherited during fork and when
31-bit process forks a child (but does not perform exec) it ends up
with 64-bit vdso. To address that, init_new_context (which is called
during fork and exec) now initialize compat_mm based on thread TIF_31BIT
flag. Later compat_mm is adjusted in arch_setup_additional_pages, which
is called during exec.

Fixes: d1befa65823e ("s390/vdso: avoid 64-bit vdso mapping for compat tasks")
Reported-by: Stefan Liebler <stli@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: ov2680: fix null dereference at power on

[ Upstream commit c45fbdf24c61a7b7a37f1b3bbd46f054637a3627 ]

Swapping the order between v4l2 subdevice registration and checking chip
id in b7a417628abf ("media: ov2680: don't register the v4l2 subdevice
before checking chip ID") makes the mode restore to use the sensor
controls before they are set, so move the mode restore call to s_power
after the handler setup for controls is done.

This remove also the need for the error code path in power on function.

Fixes: b7a417628abf ("media: ov2680: don't register the v4l2 subdevice before checking chip ID")

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/iser: Fix possible NULL deref at iser_inv_desc()

[ Upstream commit 65f07f5a09dacf3b60619f196f096ea3671a5eda ]

In case target remote invalidates bogus rkey and signature is not used,
pi_ctx is NULL deref.

The commit also fails the connection on bogus remote invalidation.

Fixes: 59caaed7a72a ("IB/iser: Support the remote invalidation exception")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fuse: use READ_ONCE on congestion_threshold and max_background

[ Upstream commit 2a23f2b8adbe4bd584f936f7ac17a99750eed9d7 ]

Since they are of unsigned int type, it's allowed to read them
unlocked during reporting to userspace. Let's underline this fact
with READ_ONCE() macroses.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: usbtmc: uninitialized symbol 'actual' in usbtmc_ioctl_clear

[ Upstream commit 9a83190300867fb024d53f47c31088e34188efc1 ]

Fix uninitialized symbol 'actual' in function usbtmc_ioctl_clear.

When symbol 'actual' is not initialized and usb_bulk_msg() fails,
the subsequent kernel debug message shows a random value.

Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: dfee02ac4bce ("usb: usbtmc: Fix ioctl USBTMC_IOCTL_CLEAR")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: xhci-mtk: fix ISOC error when interval is zero

[ Upstream commit 87173acc0d8f0987bda8827da35fff67f52ad15d ]

If the interval equal zero, needn't round up to power of two
for the number of packets in each ESIT, so fix it.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: masquerade: don't flush all conntracks if only one address deleted on device

[ Upstream commit 097f95d319f817e651bd51f8846aced92a55a6a1 ]

We configured iptables as below, which only allowed incoming data on
established connections:

iptables -t mangle -A PREROUTING -m state --state ESTABLISHED -j ACCEPT
iptables -t mangle -P PREROUTING DROP

When deleting a secondary address, current masquerade implements would
flush all conntracks on this device. All the established connections on
primary address also be deleted, then subsequent incoming data on the
connections would be dropped wrongly because it was identified as NEW
connection.

So when an address was delete, it should only flush connections related
with the address.

Signed-off-by: Tan Hu <tan.hu@zte.com.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: armada38x: fix possible race condition

[ Upstream commit 7d61cbb945a753af08e247b5f10bdd5dbb8d6c80 ]

The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.

Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: tx4939: fixup nvmem name and register size

[ Upstream commit 2ab78755e93a10f6216c860a2012f3592f395603 ]

The default word_size and stride of 1 are correct for the tx4939. Also fix
the nvmem folder name.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: isl1208: avoid possible sysfs race

[ Upstream commit 1b4c794fda583edabe864ac466e9cd43c707be80 ]

Use rtc_add_group to add the common sysfs group to avoid a possible race
condition.

[Denis.Osterland@diehl.com: use to_i2c_client(dev->parent)]
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The move of atrim, dtrim usr sysfs properties from i2c device
to rtc device require to access them via dev->parent.
This patch also aligns timestamp0.

Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: lpc32xx: Fix SPI controller node names

[ Upstream commit 11236ef582b8d66290bb3b3710e03ca1d85d8ad8 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: lg: Fix SPI controller node names

[ Upstream commit 09bae3b64cb580c95329bd8d16f08f0a5cb81ec9 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: amd: Fix SPI bus warnings

[ Upstream commit e9f0878c4b2004ac19581274c1ae4c61ae3ca70e ]

dtc has new checks for SPI buses. Fix the warnings in node names.

arch/arm64/boot/dts/amd/amd-overdrive.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'

Cc: Brijesh Singh <brijeshkumar.singh@amd.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Check for bus reset

[ Upstream commit 6b0e87a6aafe12d75c2bea6fc8e49e88b98b3083 ]

The SR_RST bit isn't latched. Hence, detecting a bus reset isn't reliable.
When it is detected, the right thing to do is to drop all connected and
disconnected commands. The code for that is already present so refactor it and
call it when SR_RST is set.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Handle BUS FREE during reselection

[ Upstream commit ca694afad707cb3ae2fdef3b28454444d9ac726e ]

The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Don't call dsprintk() following reselection interrupt

[ Upstream commit 08267216b3f8aa5adc204bdccf8deb72c1cd7665 ]

The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",

    ... The reselected initiator shall then assert the BSY signal
    within a selection abort time of its most recent detection of being
    reselected; this is required for correct operation of the time-out
    procedure.

The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Don't clear busy flag when abort fails

[ Upstream commit 45ddc1b24806cc8f1a09f23dd4e7b6e4a8ae36e1 ]

When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Check for invalid reselection target

[ Upstream commit 7ef55f6744c45e3d7c85a3f74ada39b67ac741dd ]

The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Use DRIVER_SENSE to indicate valid sense data

[ Upstream commit 070356513963be6196142acff56acc8359069fa1 ]

When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE).  Otherwise
some callers of scsi_execute() will ignore sense data.  Don't set DID_ERROR or
DID_RESET just because sense data is missing.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Withhold disconnect privilege for REQUEST SENSE

[ Upstream commit 7c8ed783c2faa1e3f741844ffac41340338ea0f4 ]

This is mostly needed because an AztecMonster II target has been observed
disconnecting REQUEST SENSE commands and then failing to reselect properly.

Suggested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Have NCR5380_select() return a bool

[ Upstream commit dad8261e643849ea134c7cd5c8e794e31d93b9eb ]

The return value is taken to mean "retry" or "don't retry". Change it to bool
to improve readability. Fix related comments. No functional change.

Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: NCR5380: Clear all unissued commands on host reset

[ Upstream commit 1aeeeed7f03c576f096eede7b0384f99a98f588c ]

When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.

[mkp: adjusted Hannes' SoB address]

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ondrey Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: Allow TKIP for AP mode

[ Upstream commit 6f3df8c1192c873a6ad9a76328920f6f85af90a8 ]

Support for setting keys for TKIP cipher suite was mistakenly removed
for AP mode. Fix this.

Fixes: 85aeb58cec1a ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: mvm: use correct FIFO length

[ Upstream commit 7126b6f2bbdf8e25f85e7ca6d91d49ea4ce9f6a6 ]

Current FIFO size calculation is wrong for two reasons:
- We access lmac 0 by default
- We don't take 11ax into consideration.
Fix both.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: pcie: fit reclaim msg to MAX_MSG_LEN

[ Upstream commit 81f0c66187e1ebb7b63529d82faf7ff1e0ef428a ]

Today, the length of a debug message in iwl_trans_pcie_reclaim
may pass the MAX_MSG_LEN, which is 110.
An example for this kind of message is:

'iwl_trans_pcie_reclaim: Read index for DMA queue txq id (2),
last_to_free 65535 is out of range [0-65536] 2 2.'

Cut the message a bit so it will fit the allowed MAX_MSG_LEN.

Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: pcie: gen2: build A-MSDU only for GSO

[ Upstream commit 53f474e6a8d74d5dc0c3a015d889471f9a157685 ]

If the incoming frame should be an A-MSDU, it may already be one,
for example in the case of NAN multicast being encapsulated in an
A-MSDU. Thus, use the GSO algorithm to build A-MSDU only if the
skb actually contains GSO data.

Fixes: 6ffe5de35b05 ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: api: annotate compressed BA notif array sizes

[ Upstream commit 6f68cc367ab6578a33cca21b6056804165621f00 ]

Annotate the compressed BA notification array sizes and
make both of them 0-length since the length of 1 is just
confusing - it may be different than that and the offset
to the second one needs to be calculated in the C code
anyhow.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: pcie: read correct prph address for newer devices

[ Upstream commit 84fb372c892e231e9a2ffdaa5c2df52d94aa536c ]

For newer devices we have higher range of periphery
addresses. Currently it is masked out, so we end up
reading another address.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: fix non_shared_ant for 22000 devices

[ Upstream commit a40287727d9b737e183959fd31a4e0c55f312853 ]

The non-shared antenna was wrong for 22000 device series.
Fix it to ANT_B for correct antenna preference by coex in MVM driver.

Fixes: e34d975e40ff ("iwlwifi: Add a000 HW family support")
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: dbg: don't crash if the firmware crashes in the middle of a debug dump

[ Upstream commit 79f25b10c9da3dbc953e47033d0494e51580ac3b ]

We can dump data from the firmware either when it crashes,
or when the firmware is alive.
Not all the data is available if the firmware is running
(like the Tx / Rx FIFOs which are available only when the
firmware is halted), so we first check that the firmware
is alive to compute the required size for the dump and then
fill the buffer with the data.

When we allocate the buffer, we test the STATUS_FW_ERROR
bit to check if the firmware is alive or not. This bit
can be changed during the course of the dump since it is
modified in the interrupt handler.

We hit a case where we allocate the buffer while the
firmware is sill working, and while we start to fill the
buffer, the firmware crashes. Then we test STATUS_FW_ERROR
again and decide to fill the buffer with data like the
FIFOs even if no room was allocated for this data in the
buffer. This means that we overflow the buffer that was
allocated leading to memory corruption.

To fix this, test the STATUS_FW_ERROR bit only once and
rely on local variables to check if we should dump fifos
or other firmware components.

Fixes: 04fd2c28226f ("iwlwifi: mvm: add rxf and txf to dump data")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: fix a memory leak in rsa-kcs1pad's encryption mode

[ Upstream commit 3944f139d5592790b70bc64f197162e643a8512b ]

The encryption mode of pkcs1pad never uses out_sg and out_buf, so
there's no need to allocate the buffer, which presently is not even
being freed.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: linux-crypto@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Dan Aloni <dan@kernelim.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: s5p-sss: Fix Fix argument list alignment

[ Upstream commit 6c12b6ba45490eeb820fdceccf5a53f42a26799c ]

Fix misalignment of continued argument list.

Signed-off-by: Christoph Manszewski <c.manszewski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: s5p-sss: Fix race in error handling

[ Upstream commit 5842cd44786055231b233ed5ed98cdb63ffb7db3 ]

Remove a race condition introduced by error path in functions:
s5p_aes_interrupt and s5p_aes_crypt_start. Setting the busy field of
struct s5p_aes_dev to false made it possible for s5p_tasklet_cb to
change the req field, before s5p_aes_complete was called.

Change the first parameter of s5p_aes_complete to struct
ablkcipher_request. Before spin_unlock, make a copy of the currently
handled request, to ensure s5p_aes_complete function call with the
correct request.

Signed-off-by: Christoph Manszewski <c.manszewski@samsung.com>
Acked-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/hyperv: Suppress "PCI: Fatal: No config space access function found"

[ Upstream commit 2f285f46240d67060061d153786740d4df53cd78 ]

A Generation-2 Linux VM on Hyper-V doesn't have the legacy PCI bus, and
users always see the scary warning, which is actually harmless.

Suppress it.

Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: "devel@linuxdriverproject.org" <devel@linuxdriverproject.org>
Cc: Olaf Aepfle <olaf@aepfle.de>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Marcelo Cerri <marcelo.cerri@canonical.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Link: https://lkml.kernel.org/r/
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: btrsi: fix bt tx timeout issue

[ Upstream commit 7cbfd1e2aad410d96fa6162aeb3f9cff1fecfc58 ]

observed sometimes data is coming with unaligned address from kernel
BT stack. If unaligned address is passed, some data in payload is
stripped when packet is loading to firmware and this results, BT
connection timeout is happening.

sh# hciconfig hci0 up
Can't init device hci0: hci0 command 0x0c03 tx timeout

Fixed this by moving the data to aligned address.

Signed-off-by: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: L2CAP: Detect if remote is not able to use the whole MPS

[ Upstream commit a5c3021bb62b970713550db3f7fd08aa70665d7e ]

If the remote is not able to fully utilize the MPS choosen recalculate
the credits based on the actual amount it is sending that way it can
still send packets of MTU size without credits dropping to 0.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: hci_serdev: clear HCI_UART_PROTO_READY to avoid closing proto races

[ Upstream commit 7cf7846d27bfc9731e449857db3eec5e0e9701ba ]

Clearing HCI_UART_PROTO_READY will avoid usage of proto function pointers
before running the proto close function pointer. There is chance of kernel
crash, due to usage of non proto close function pointers after proto close.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: dell_rbu: Make payload memory uncachable

[ Upstream commit 6aecee6ad41cf97c0270f72da032c10eef025bf0 ]

The dell_rbu driver takes firmware update payloads and puts them in memory so
the system BIOS can find them after a reboot.  This sometimes fails (though
rarely), because the memory containing the payload is in the CPU cache but
never gets written back to main memory before the system is rebooted (CPU
cache contents are lost on reboot).

With this patch, the payload memory will be changed to uncachable to ensure
that the payload is actually in main memory before the system is rebooted.

Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: realview: Fix SPI controller node names

[ Upstream commit 016add12977bcc30f77d7e48fc9a3a024cb46645 ]

SPI controller nodes should be named 'spi' rather than 'ssp'. Fixing the
name enables dtc SPI bus checks.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

EDAC: Raise the maximum number of memory controllers

[ Upstream commit 6b58859419554fb824e09cfdd73151a195473cbc ]

We observe an oops in the skx_edac module during boot:

  EDAC MC0: Giving out device to module skx_edac controller Skylake Socket#0 IMC#0
  EDAC MC1: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
  EDAC MC2: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
  ...
  EDAC MC13: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
  EDAC MC14: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
  EDAC MC15: Giving out device to module skx_edac controller Skylake Socket#1 IMC#1
  Too many memory controllers: 16
  EDAC MC: Removed device 0 for skx_edac Skylake Socket#0 IMC#0

We observe there are two memory controllers per socket, with a limit
of 16. Raise the maximum number of memory controllers from 16 to 2 *
MAX_NUMNODES (1024).

[ bp: This is just a band-aid fix until we've sorted out the whole issue
  with the bus_type association and handling in EDAC and can get rid of
  this arbitrary limit. ]

Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Russ Anderson <russ.anderson@hpe.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac@vger.kernel.org
Link: https://lkml.kernel.org/r/20180925143449.284634-1-justin.ernst@hpe.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA: Fix dependencies for rdma_user_mmap_io

[ Upstream commit 46bdf777685677c1cc6b3da9220aace9da690731 ]

The mlx4 driver produces a link error when it is configured
as built-in while CONFIG_INFINIBAND_USER_ACCESS is set to =m:

drivers/infiniband/hw/mlx4/main.o: In function `mlx4_ib_mmap':
main.c:(.text+0x1af4): undefined reference to `rdma_user_mmap_io'

The same function is called from mlx5, which already has a
dependency to ensure we can call it, and from hns, which
appears to suffer from the same problem.

This adds the same dependency that mlx5 uses to the other two.

Fixes: 6745d356ab39 ("RDMA/hns: Use rdma_user_mmap_io")
Fixes: c282da4109e4 ("RDMA/mlx4: Use rdma_user_mmap_io")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: mark inode dirty explicitly in recover_inode()

[ Upstream commit 4a1728cad6340bfbe17bd17fd158b2165cd99508 ]

Mark inode dirty explicitly in the end of recover_inode() to make sure
that all recoverable fields can be persisted later.

Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix to recover inode's project id during POR

[ Upstream commit f4474aa6e5e901ee4af21f39f1b9115aaaaec503 ]

Testcase to reproduce this bug:
1. mkfs.f2fs -O extra_attr -O project_quota /dev/sdd
2. mount -t f2fs /dev/sdd /mnt/f2fs
3. touch /mnt/f2fs/file
4. sync
5. chattr -p 1 /mnt/f2fs/file
6. xfs_io -f /mnt/f2fs/file -c "fsync"
7. godown /mnt/f2fs
8. umount /mnt/f2fs
9. mount -t f2fs /dev/sdd /mnt/f2fs
10. lsattr -p /mnt/f2fs/file

    0 -----------------N- /mnt/f2fs/file

But actually, we expect the correct result is:

    1 -----------------N- /mnt/f2fs/file

The reason is we didn't recover inode.i_projid field during mount,
fix it.

Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: update i_size after DIO completion

[ Upstream commit 0a4daae5ffea39f5015334e4d18a6a80b447cae4 ]

This is related to
ee70daaba82d ("xfs: update i_size after unwritten conversion in dio completion")

If we update i_size during dio_write, dio_read can read out stale data, which
breaks xfstests/465.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI/ERR: Run error recovery callbacks for all affected devices

[ Upstream commit bfcb79fca19d267712e425af1dd48812c40dec0c ]

If an Endpoint reported an error with ERR_FATAL, we previously ran driver
error recovery callbacks only for the Endpoint's driver.  But if we reset a
Link to recover from the error, all downstream components are affected,
including the Endpoint, any multi-function peers, and children of those
peers.

Initiate the Link reset from the deepest Downstream Port that is
reliable, and call the error recovery callbacks for all its children.

If a Downstream Port (including a Root Port) reports an error, we assume
the Port itself is reliable and we need to reset its downstream Link.  In
all other cases (Switch Upstream Ports, Endpoints, Bridges, etc), we assume
the Link leading to the component needs to be reset, so we initiate the
reset at the parent Downstream Port.

This allows two other clean-ups.  First, we currently only use a Link
reset, which can only be initiated using a Downstream Port, so we can
remove checks for Endpoints.  Second, the Downstream Port where we initiate
the Link reset is reliable (unlike components downstream from it), so the
special cases for error detect and resume are no longer necessary.

Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: faraday: fix return type of ndo_start_xmit function

[ Upstream commit 0a715156656bddf4aa92d9868f850aeeb0465fd0 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: smsc: fix return type of ndo_start_xmit function

[ Upstream commit 6323d57f335ce1490d025cacc83fc10b07792130 ]

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: paz00: fix wakeup gpio keycode

[ Upstream commit ebea2a43fdafdbce918bd7e200b709d6c33b9f3b ]

The power key is controlled solely by the EC, which only tiggeres this
gpio after wakeup.
Fixes immediately return to suspend after wake from LP1.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: tegra: colibri_t30: fix mcp2515 can controller interrupt polarity

[ Upstream commit 503fcd8464fb6cd18073e97dec59b933930655d6 ]

Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarity

[ Upstream commit b38f6aa4b60a1fcc41f5c469981f8f62d6070ee3 ]

Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: tegra: apalis_t30: fix mmc1 cmd pull-up

[ Upstream commit 1c997fe4becdc6fcbc06e23982ceb65621e6572a ]

Fix MMC1 cmd pin pull-up causing issues on carrier boards without
external pull-up.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: tegra20: restore address order

[ Upstream commit 8188391c127ea34d66f37eda6755d0acb51dc600 ]

Commit 6c468f109884 ("ARM: dts: tegra: add Tegra20 NAND flash
controller node") introduced the nand-controller node. However, it got
added at the wrong spot not honoring the address order. Fix this.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: tegra30: fix xcvr-setup-use-fuses

[ Upstream commit 564706f65cda3de52b09e51feb423a43940fe661 ]

There was a dot instead of a comma. Fix this.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: tegra: I2C on Tegra194 is not compatible with Tegra114

[ Upstream commit d9fd22447ba59a9b53a202fade977e82bfba8d8d ]

Tegra194 contains a version of the I2C controller that is no longer
compatible with the version found in Tegra114.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx51-zii-rdu1: Fix the rtc compatible string

[ Upstream commit 1c5f335f61ffb838fc3cc1cec9464067663eb8c8 ]

According to Documentation/devicetree/bindings/rtc/rtc-ds1307.txt the
original compatible "maxim,ds1341" is not a valid entry.

Switch to the documented "dallas,ds1341" compatible.

Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: fsl: Fix I2C and SPI bus warnings

[ Upstream commit b739c177e1aeab532f355493439a1901b85be38c ]

dtc has new checks for I2C and SPI buses. Fix the SPI bus node names
and warnings in unit-addresses.

arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dtb: Warning (i2c_bus_reg): /soc/i2c@2180000/eeprom@57: I2C bus unit address format error, expected "53"
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dtb: Warning (i2c_bus_reg): /soc/i2c@2180000/eeprom@56: I2C bus unit address format error, expected "52"

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: lantiq: Fix compile warning

[ Upstream commit 3a00dae006623d799266d85f28b5f76ef07d6b6c ]

This local variable is unused, remove it.

Fixes: dea54fbad332 ("phy: Add an USB PHY driver for the Lantiq SoCs using the RCU module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix remount problem of option io_bits

[ Upstream commit c6b1867b1da3b1203b4c49988afeebdcbdf65499 ]

Currently we show mount option "io_bits=%u" as "io_size=%uKB",
it will cause option parsing problem(unrecognized mount option)
in remount.

Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: libsas: always unregister the old device if going to discover new

[ Upstream commit 32c850bf587f993b2620b91e5af8a64a7813f504 ]

If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.

And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.

Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iw_cxgb4: Use proper enumerated type in c4iw_bar2_addrs

[ Upstream commit 1b571086e869395b6a11ab24186b0104fe05c057 ]

Clang warns when one enumerated type is implicitly converted to another.

drivers/infiniband/hw/cxgb4/qp.c:287:8: warning: implicit conversion
from enumeration type 'enum t4_bar2_qtype' to different enumeration type
'enum cxgb4_bar2_qtype' [-Wenum-conversion]
                                                 T4_BAR2_QTYPE_EGRESS,
                                                 ^~~~~~~~~~~~~~~~~~~~

c4iw_bar2_addrs expects a value from enum cxgb4_bar2_qtype so use the
corresponding values from that type so Clang is satisfied without changing
the meaning of the code.

T4_BAR2_QTYPE_EGRESS = CXGB4_BAR2_QTYPE_EGRESS = 0
T4_BAR2_QTYPE_INGRESS = CXGB4_BAR2_QTYPE_INGRESS = 1

Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vfio/pci: Mask buggy SR-IOV VF INTx support

[ Upstream commit db04264fe9bc0f2b62e036629f9afb530324b693 ]

The SR-IOV spec requires that VFs must report zero for the INTx pin
register as VFs are precluded from INTx support.  It's much easier for
the host kernel to understand whether a device is a VF and therefore
whether a non-zero pin register value is bogus than it is to do the
same in userspace.  Override the INTx count for such devices and
virtualize the pin register to provide a consistent view of the device
to the user.

As this is clearly a spec violation, warn about it to support hardware
validation, but also provide a known whitelist as it doesn't do much
good to continue complaining if the hardware vendor doesn't plan to
fix it.

Known devices with this issue: 8086:270c

Tested-by: Gage Eads <gage.eads@intel.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vfio/pci: Fix potential memory leak in vfio_msi_cap_len

[ Upstream commit 30ea32ab1951c80c6113f300fce2c70cd12659e4 ]

Free allocated vdev->msi_perm in error path.

Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vmbus: keep pointer to ring buffer page

[ Upstream commit 52a42c2a90226dc61c99bbd0cb096deeb52c334b ]

Avoid going from struct page to virt address (and back) by just
keeping pointer to the allocated pages instead of virt address.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: genwqe: should return proper error value.

[ Upstream commit 02241995b004faa7d9ff628e97f24056190853f8 ]

The function should return -EFAULT when copy_from_user fails. Even
though the caller does not distinguish them. but we should keep backward
compatibility.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: kgdbts: Fix restrict error

[ Upstream commit fa0218ef733e6f247a1a3986e3eb12460064ac77 ]

kgdbts current fails when compiled with restrict:

drivers/misc/kgdbts.c: In function ‘configure_kgdbts’:
drivers/misc/kgdbts.c:1070:2: error: ‘strcpy’ source argument is the same as destination [-Werror=restrict]
  strcpy(config, opt);
  ^~~~~~~~~~~~~~~~~~~

As the error says, config is being used in both the source and destination.
Refactor the code to avoid the extra copy and put the parsing closer to
the actual location.

Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>