review.tizen.org Git - platform/kernel/linux-starfive.git/log

riscv: fix misaligned access handling of C.SWSP and C.SDSP

[ Upstream commit 22e0eb04837a63af111fae35a92f7577676b9bc8 ]

This is a backport of a fix that was done in OpenSBI: ec0559eb315b
("lib: sbi_misaligned_ldst: Fix handling of C.SWSP and C.SDSP").

Unlike C.LWSP/C.LDSP, these encodings can be used with the zero
register, so checking that the rs2 field is non-zero is unnecessary.

Additionally, the previous check was incorrect since it was checking
the immediate field of the instruction instead of the rs2 field.

Fixes: 956d705dd279 ("riscv: Unaligned load/store handling for M_MODE")
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Link: https://lore.kernel.org/r/20231103090223.702340-1-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Fix eMMC Data Strobe PD on rk3588

[ Upstream commit 37f3d6108730713c411827ab4af764909f4dfc78 ]

JEDEC standard JESD84-B51 defines the eMMC Data Strobe line, which is
currently used only in HS400 mode, as a device->host clock signal that
"is used only in read operation. The Data Strobe is always High-Z (not
driven by the device and pulled down by RDS) or Driven Low in write
operation, except during CRC status response." RDS is a pull-down
resistor specified in the 10K-100K ohm range. Thus per the standard, the
Data Strobe is always pulled to ground (by the eMMC and/or RDS) during
write operations.

Evidently, the eMMC host controller in the RK3588 considers an active
voltage on the eMMC-DS line during a write to be an error.

The default (i.e. hardware reset, and Rockchip BSP) behavior for the
RK3588 is to activate the eMMC-DS pin's builtin pull-down. As a result,
many RK3588 board designers do not bother adding a dedicated RDS
resistor, instead relying on the RK3588's internal bias. The current
devicetree, however, disables this bias (`pcfg_pull_none`), breaking
HS400-mode writes for boards without a dedicated RDS, but with an eMMC
chip that chooses to High-Z (instead of drive-low) the eMMC-DS line.
(The Turing RK1 is one such board.)

Fix this by changing the bias in the (common) emmc_data_strobe case to
reflect the expected hardware/BSP behavior. This is unlikely to cause
regressions elsewhere: the pull-down is only relevant for High-Z eMMCs,
and if this is redundant with a (dedicated) RDS resistor, the effective
result is only a lower resistance to ground -- where the range of
tolerance is quite high. If it does, it's better fixed in the specific
devicetrees.

Fixes: d85f8a5c798d5 ("arm64: dts: rockchip: Add rk3588 pinctrl data")
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://lore.kernel.org/r/20231205202900.4617-2-CFSworks@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx28-xea: Pass the 'model' property

[ Upstream commit 63ef8fc9bcee6b73ca445a19a7ac6bd544723c9f ]

Per root-node.yaml, 'model' is a required property.

Pass it to fix the following dt-schema warning:

imx28-xea.dtb: /: 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#

Signed-off-by: Fabio Estevam <festevam@denx.de>
Fixes: 445ae16ac1c5 ("ARM: dts: imx28: Add DTS description of imx28 based XEA board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt

[ Upstream commit 397caf68e2d36532054cb14ae8995537f27f8b61 ]

The timer nodes declare compatibility with "fsl,imx6sx-gpt", which
itself is compatible with "fsl,imx6dl-gpt". Switch the fallback
compatible from "fsl,imx6sx-gpt" to "fsl,imx6dl-gpt".

Fixes: 949673450291 ("ARM: dts: add imx7d soc dtsi file")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: imx8-apalis: set wifi regulator to always-on

[ Upstream commit 04179605ab604dba32571a05cd06423afc9eca19 ]

Make sure that the wifi regulator is always on. The wifi driver itself
puts the wifi module into suspend mode. If we cut the power the driver
will crash when resuming from suspend.

Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fixes: ad0de4ceb706 ("arm64: dts: freescale: add initial apalis imx8 aka quadmax module support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init

[ Upstream commit 1c2b1049af3f86545fcc5fae0fc725fb64b3a09e ]

devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.

Release the id allocated in 'mmdc_pmu_init' when 'devm_kasprintf'
return NULL

Suggested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Fixes: e76bdfd7403a ("ARM: imx: Added perf functionality to mmdc driver")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: imx93: correct mediamix power

[ Upstream commit d4cb68a5d3a1ed30ecaf1591eb901523faa13496 ]

"nic_media" clock should be enabled when power on/off mediamix, otherwise
power on/off will fail. Because "media_axi_root" clock is the parent of
"nic_media" clock, so replace "media_axi_clock" clock with "nic_media"
clock in mediamix node.

Link: https://github.com/nxp-imx/linux-imx/commit/ce18e6d0071ae9df5486af8613708ebe920484be
Fixes: f2d03ba997cb ("arm64: dts: imx93: reorder device nodes")
Fixes: e85d3458a804 ("arm64: dts: imx93: add src node")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells

[ Upstream commit d863a2f4f47560d71447650822857fc3d2aea715 ]

i.MX8QM/QXP supports inverted PWM output, thus #pwm-cells needs to be set
to 3.

Fixes: 23fa99b205ea ("arm64: dts: freescale: imx8-ss-lsio: add support for lsio_pwm0-3")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: imx8-ss-lsio: Add PWM interrupts

[ Upstream commit 6c32f75d67a8c1ea94295234db7c11a29c189e6f ]

The PWM interrupt is mandatory per imx-pwm.yaml.

Add them.

This also fixes the followig schema warning:

imx8qm-apalis-v1.1-ixora-v1.2.dtb: pwm@5d000000: 'oneOf' conditional failed, one must be fixed:
'interrupts' is a required property
'interrupts-extended' is a required property
from schema $id: http://devicetree.org/schemas/pwm/imx-pwm.yaml#

Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: d863a2f4f475 ("arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells")
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: be2iscsi: Fix a memleak in beiscsi_init_wrb_handle()

[ Upstream commit 235f2b548d7f4ac5931d834f05d3f7f5166a2e72 ]

When an error occurs in the for loop of beiscsi_init_wrb_handle(), we
should free phwi_ctxt->be_wrbq before returning an error code to prevent
potential memleak.

Fixes: a7909b396ba7 ("[SCSI] be2iscsi: Fix dynamic CID allocation Mechanism in driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20231123081941.24854-1-dinghao.liu@zju.edu.cn
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Fix a warning when allocating buffered events fails

[ Upstream commit 34209fe83ef8404353f91ab4ea4035dbc9922d04 ]

Function trace_buffered_event_disable() produces an unexpected warning
when the previous call to trace_buffered_event_enable() fails to
allocate pages for buffered events.

The situation can occur as follows:

* The counter trace_buffered_event_ref is at 0.

* The soft mode gets enabled for some event and
  trace_buffered_event_enable() is called. The function increments
  trace_buffered_event_ref to 1 and starts allocating event pages.

* The allocation fails for some page and trace_buffered_event_disable()
  is called for cleanup.

* Function trace_buffered_event_disable() decrements
  trace_buffered_event_ref back to 0, recognizes that it was the last
  use of buffered events and frees all allocated pages.

* The control goes back to trace_buffered_event_enable() which returns.
  The caller of trace_buffered_event_enable() has no information that
  the function actually failed.

* Some time later, the soft mode is disabled for the same event.
  Function trace_buffered_event_disable() is called. It warns on
  "WARN_ON_ONCE(!trace_buffered_event_ref)" and returns.

Buffered events are just an optimization and can handle failures. Make
trace_buffered_event_enable() exit on the first failure and left any
cleanup later to when trace_buffered_event_disable() is called.

Link: https://lore.kernel.org/all/20231127151248.7232-2-petr.pavlu@suse.com/
Link: https://lkml.kernel.org/r/20231205161736.19663-3-petr.pavlu@suse.com
Fixes: 0fc1b09ff1ff ("tracing: Use temp buffer when filtering events")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring/kbuf: check for buffer list readiness after NULL check

[ Upstream commit 9865346b7e8374b57f1c3ccacdc77846c6352ff4 ]

Move the buffer list 'is_ready' check below the validity check for
the buffer list for a given group.

Fixes: 5cf4f52e6d8a ("io_uring: free io_buffer_list entries via RCU")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring/kbuf: Fix an NULL vs IS_ERR() bug in io_alloc_pbuf_ring()

[ Upstream commit e53f7b54b1fdecae897f25002ff0cff04faab228 ]

The io_mem_alloc() function returns error pointers, not NULL. Update
the check accordingly.

Fixes: b10b73c102a2 ("io_uring/kbuf: recycle freed mapped buffer ring entries")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/5ed268d3-a997-4f64-bd71-47faa92101ab@moroto.mountain
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock

[ Upstream commit d951f8f5f23a9417b7952f22b33784c73caa1ebb ]

Since commit c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK
specific PHY fixup")thet Ethernet PHY is no longer configured via code
in board file.

This caused Ethernet to stop working.

Fix this problem by describing the clocks and clock-names to the
Ethernet PHY node so that the KSZ8081 chip can be clocked correctly.

Fixes: c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3

[ Upstream commit 209043cf092d7b0d4739921b3f11d6d0b451eabf ]

The i.MX8MP and i.MX8MQ devices both use the same DWC3 controller and
are both affected by a known issue with the controller due to specific
behaviour when park mode is enabled in SuperSpeed host mode operation.

Under heavy USB traffic from multiple endpoints the controller will
sometimes incorrectly process transactions such that some transactions
are lost, or the controller may hang when processing transactions. When
the controller hangs it does not recover.

This issue is documented partially within the linux-imx vendor kernel
which references a Synopsys STAR number 9001415732 in commits [1] and
additional details in [2]. Those commits provide some additional
controller internal implementation specifics around the incorrect
behaviour of the SuperSpeed host controller operation when park mode is
enabled.

The summary of this issue is that the host controller can incorrectly
enter/exit park mode such that part of the controller is in a state
which behaves as if in park mode even though it is not. In this state
the controller incorrectly calculates the number of TRBs available which
results in incorrect access of the internal caches causing the overwrite
of pending requests in the cache which should have been processed but
are ignored. This can cause the controller to drop the requests or hang
waiting for the pending state of the dropped requests.

The workaround for this issue is to disable park mode for SuperSpeed
operation of the controller through the GUCTL1[17] bit. This is already
available as a quirk for the DWC3 controller and can be enabled via the
'snps,parkmode-disable-ss-quirk' device tree property.

It is possible to replicate this failure on an i.MX8MP EVK with a USB
Hub connecting 4 SuperSpeed USB flash drives. Performing continuous
small read operations (dd if=/dev/sd... of=/dev/null bs=16) on the block
devices will result in device errors initially and will eventually
result in the controller hanging.

  [13240.896936] xhci-hcd xhci-hcd.0.auto: WARN Event TRB for slot 4 ep 2 with no TDs queued?
  [13240.990708] usb 2-1.3: reset SuperSpeed USB device number 5 using xhci-hcd
  [13241.015582] sd 2:0:0:0: [sdc] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x07 driverbyte=DRIVER_OK cmd_age=0s
  [13241.025198] sd 2:0:0:0: [sdc] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
  [13241.032949] I/O error, dev sdc, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 25 prio class 2
  [13272.150710] usb 2-1.2: reset SuperSpeed USB device number 4 using xhci-hcd
  [13272.175469] sd 1:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x03 driverbyte=DRIVER_OK cmd_age=31s
  [13272.185365] sd 1:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
  [13272.193385] I/O error, dev sdb, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2
  [13434.846556] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command
  [13434.854592] xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
  [13434.862553] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up

[1] https://github.com/nxp-imx/linux-imx/commit/97a5349d936b08cf301730b59e4e8855283f815c
[2] https://github.com/nxp-imx/linux-imx/commit/b4b5cbc5a12d7c3b920d1d7cba0ada3379e4e42b

Fixes: fb8587a2c165 ("arm64: dtsi: imx8mp: add usb nodes")
Fixes: ad37549cb5dc ("arm64: dts: imx8mq: add USB nodes")
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/bridge: tc358768: select CONFIG_VIDEOMODE_HELPERS

[ Upstream commit 26513300978f7285c3e776c144f27ef71be61f57 ]

A dependency on this feature was recently introduced:

x86_64-linux-ld: vmlinux.o: in function `tc358768_bridge_pre_enable':
tc358768.c:(.text+0xbe3dae): undefined reference to `drm_display_mode_to_videomode'

Make sure this is always enabled.

Fixes: e5fb21678136 ("drm/bridge: tc358768: Use struct videomode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231204072814.968816-1-arnd@kernel.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204072814.968816-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/irdma: Avoid free the non-cqp_request scratch

[ Upstream commit e3e82fcb79eeb3f1a88a89f676831773caff514a ]

When creating ceq_0 during probing irdma, cqp.sc_cqp will be sent as a
cqp_request to cqp->sc_cqp.sq_ring. If the request is pending when
removing the irdma driver or unplugging its aux device, cqp.sc_cqp will be
dereferenced as wrong struct in irdma_free_pending_cqp_request().

  PID: 3669   TASK: ffff88aef892c000  CPU: 28  COMMAND: "kworker/28:0"
   #0 [fffffe0000549e38] crash_nmi_callback at ffffffff810e3a34
   #1 [fffffe0000549e40] nmi_handle at ffffffff810788b2
   #2 [fffffe0000549ea0] default_do_nmi at ffffffff8107938f
   #3 [fffffe0000549eb8] do_nmi at ffffffff81079582
   #4 [fffffe0000549ef0] end_repeat_nmi at ffffffff82e016b4
      [exception RIP: native_queued_spin_lock_slowpath+1291]
      RIP: ffffffff8127e72b  RSP: ffff88aa841ef778  RFLAGS: 00000046
      RAX: 0000000000000000  RBX: ffff88b01f849700  RCX: ffffffff8127e47e
      RDX: 0000000000000000  RSI: 0000000000000004  RDI: ffffffff83857ec0
      RBP: ffff88afe3e4efc8   R8: ffffed15fc7c9dfa   R9: ffffed15fc7c9dfa
      R10: 0000000000000001  R11: ffffed15fc7c9df9  R12: 0000000000740000
      R13: ffff88b01f849708  R14: 0000000000000003  R15: ffffed1603f092e1
      ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0000
  -- <NMI exception stack> --
   #5 [ffff88aa841ef778] native_queued_spin_lock_slowpath at ffffffff8127e72b
   #6 [ffff88aa841ef7b0] _raw_spin_lock_irqsave at ffffffff82c22aa4
   #7 [ffff88aa841ef7c8] __wake_up_common_lock at ffffffff81257363
   #8 [ffff88aa841ef888] irdma_free_pending_cqp_request at ffffffffa0ba12cc [irdma]
   #9 [ffff88aa841ef958] irdma_cleanup_pending_cqp_op at ffffffffa0ba1469 [irdma]
   #10 [ffff88aa841ef9c0] irdma_ctrl_deinit_hw at ffffffffa0b2989f [irdma]
   #11 [ffff88aa841efa28] irdma_remove at ffffffffa0b252df [irdma]
   #12 [ffff88aa841efae8] auxiliary_bus_remove at ffffffff8219afdb
   #13 [ffff88aa841efb00] device_release_driver_internal at ffffffff821882e6
   #14 [ffff88aa841efb38] bus_remove_device at ffffffff82184278
   #15 [ffff88aa841efb88] device_del at ffffffff82179d23
   #16 [ffff88aa841efc48] ice_unplug_aux_dev at ffffffffa0eb1c14 [ice]
   #17 [ffff88aa841efc68] ice_service_task at ffffffffa0d88201 [ice]
   #18 [ffff88aa841efde8] process_one_work at ffffffff811c589a
   #19 [ffff88aa841efe60] worker_thread at ffffffff811c71ff
   #20 [ffff88aa841eff10] kthread at ffffffff811d87a0
   #21 [ffff88aa841eff50] ret_from_fork at ffffffff82e0022f

Fixes: 44d9e52977a1 ("RDMA/irdma: Implement device initialization definitions")
Link: https://lore.kernel.org/r/20231130081415.891006-1-lishifeng@sangfor.com.cn
Suggested-by: "Ismail, Mustafa" <mustafa.ismail@intel.com>
Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/irdma: Fix support for 64k pages

[ Upstream commit 03769f72d66edab82484449ed594cb6b00ae0223 ]

Virtual QP and CQ require a 4K HW page size but the driver passes
PAGE_SIZE to ib_umem_find_best_pgsz() instead.

Fix this by using the appropriate 4k value in the bitmap passed to
ib_umem_find_best_pgsz().

Fixes: 693a5386eff0 ("RDMA/irdma: Split mr alloc and free into new functions")
Link: https://lore.kernel.org/r/20231129202143.1434-4-shiraz.saleem@intel.com
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/irdma: Ensure iWarp QP queue memory is OS paged aligned

[ Upstream commit 0a5ec366de7e94192669ba08de6ed336607fd282 ]

The SQ is shared for between kernel and used by storing the kernel page
pointer and passing that to a kmap_atomic().

This then requires that the alignment is PAGE_SIZE aligned.

Fix by adding an iWarp specific alignment check.

Fixes: e965ef0e7b2c ("RDMA/irdma: Split QP handler into irdma_reg_user_mr_type_qp")
Link: https://lore.kernel.org/r/20231129202143.1434-3-shiraz.saleem@intel.com
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/core: Fix umem iterator when PAGE_SIZE is greater then HCA pgsz

[ Upstream commit 4fbc3a52cd4d14de3793f4b2c721d7306ea84cf9 ]

64k pages introduce the situation in this diagram when the HCA 4k page
size is being used:

+-------------------------------------------+ <--- 64k aligned VA
|                                           |
|              HCA 4k page                  |
|                                           |
+-------------------------------------------+
|                   o                       |
|                                           |
|                   o                       |
|                                           |
|                   o                       |
+-------------------------------------------+
|                                           |
|              HCA 4k page                  |
|                                           |
+-------------------------------------------+ <--- Live HCA page
|OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO| <--- offset
|                                           | <--- VA
|                MR data                    |
+-------------------------------------------+
|                                           |
|              HCA 4k page                  |
|                                           |
+-------------------------------------------+
|                   o                       |
|                                           |
|                   o                       |
|                                           |
|                   o                       |
+-------------------------------------------+
|                                           |
|              HCA 4k page                  |
|                                           |
+-------------------------------------------+

The VA addresses are coming from rdma-core in this diagram can be
arbitrary, but for 64k pages, the VA may be offset by some number of HCA
4k pages and followed by some number of HCA 4k pages.

The current iterator doesn't account for either the preceding 4k pages or
the following 4k pages.

Fix the issue by extending the ib_block_iter to contain the number of DMA
pages like comment [1] says and by using __sg_advance to start the
iterator at the first live HCA page.

The changes are contained in a parallel set of iterator start and next
functions that are umem aware and specific to umem since there is one user
of the rdma_for_each_block() without umem.

These two fixes prevents the extra pages before and after the user MR
data.

Fix the preceding pages by using the __sq_advance field to start at the
first 4k page containing MR data.

Fix the following pages by saving the number of pgsz blocks in the
iterator state and downcounting on each next.

This fix allows for the elimination of the small page crutch noted in the
Fixes.

Fixes: 10c75ccb54e4 ("RDMA/umem: Prevent small pages from being returned by ib_umem_find_best_pgsz()")
Link: https://lore.kernel.org/r/20231129202143.1434-2-shiraz.saleem@intel.com
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: wm_adsp: fix memleak in wm_adsp_buffer_populate

[ Upstream commit 29046a78a3c0a1f8fa0427f164caa222f003cf5b ]

When wm_adsp_buffer_read() fails, we should free buf->regions.
Otherwise, the callers of wm_adsp_buffer_populate() will
directly free buf on failure, which makes buf->regions a leaked
memory.

Fixes: a792af69b08f ("ASoC: wm_adsp: Refactor compress stream initialisation")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231204074158.12026-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_scmi: Fix possible frequency truncation when using level indexing mode

[ Upstream commit 77f5032e94f244ba08db51e17ca8f37bd7ff9acb ]

The multiplier is already promoted to unsigned long, however the
frequency calculations done when using level indexing mode doesn't
use the multiplier computed. It instead hardcodes the multiplier
value of 1000 at all the usage sites.

Clean that up by assigning the multiplier value of 1000 when using
the perf level indexing mode and update the frequency calculations to
use the multiplier instead. It should fix the possible frequency
truncation for all the values greater than or equal to 4GHz on 64-bit
machines.

Fixes: 31c7c1397a33 ("firmware: arm_scmi: Add v3.2 perf level indexing mode support")
Reported-by: Sibi Sankar <quic_sibis@quicinc.com>
Closes: https://lore.kernel.org/all/20231129065748.19871-3-quic_sibis@quicinc.com/
Cc: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231130204343.503076-2-sudeep.holla@arm.com
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_scmi: Simplify error path in scmi_dvfs_device_opps_add()

[ Upstream commit 033ca4de129646e9969a6838b44cca0fac38e219 ]

Let's simplify the code in scmi_dvfs_device_opps_add() by using
dev_pm_opp_remove_all_dynamic() in the error path.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230925131715.138411-8-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Stable-dep-of: 77f5032e94f2 ("firmware: arm_scmi: Fix possible frequency truncation when using level indexing mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_scmi: Fix frequency truncation by promoting multiplier type

[ Upstream commit 8e3c98d9187e09274fc000a7d1a77b070a42d259 ]

Fix the possible frequency truncation for all values equal to or greater
4GHz on 64bit machines by updating the multiplier 'mult_factor' to
'unsigned long' type. It is also possible that the multiplier itself can
be greater than or equal to 2^32. So we need to also fix the equation
computing the value of the multiplier.

Fixes: a9e3fbfaa0ff ("firmware: arm_scmi: add initial support for performance protocol")
Reported-by: Sibi Sankar <quic_sibis@quicinc.com>
Closes: https://lore.kernel.org/all/20231129065748.19871-3-quic_sibis@quicinc.com/
Cc: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231130204343.503076-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_scmi: Extend perf protocol ops to get information of a domain

[ Upstream commit 3d99ed60721bf2e108c8fc660775766057689a92 ]

Similar to other protocol ops, it's useful for an scmi module driver to get
some generic information of a performance domain. Therefore, let's add a
new callback to provide this information. The information is currently
limited to the name of the performance domain and whether the set-level
operation is supported, although this can easily be extended if we find the
need for it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230825112633.236607-3-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Stable-dep-of: 8e3c98d9187e ("firmware: arm_scmi: Fix frequency truncation by promoting multiplier type")
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_scmi: Extend perf protocol ops to get number of domains

[ Upstream commit e9090e70e618cd62ab7bf2914511e5eea31a2535 ]

Similar to other protocol ops, it's useful for an scmi module driver to get
the number of supported performance domains, hence let's make this
available by adding a new perf protocol callback. Note that, a user is
being added from subsequent changes.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230825112633.236607-2-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Stable-dep-of: 8e3c98d9187e ("firmware: arm_scmi: Fix frequency truncation by promoting multiplier type")
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (nzxt-kraken2) Fix error handling path in kraken2_probe()

[ Upstream commit 35fe2ad259a3bfca15ab78c8ffb5278cb6149c89 ]

There is no point in calling hid_hw_stop() if hid_hw_start() has failed.
There is no point in calling hid_hw_close() if hid_hw_open() has failed.

Update the error handling path accordingly.

Fixes: 82e3430dfa8c ("hwmon: add driver for NZXT Kraken X42/X52/X62/X72")
Reported-by: Aleksa Savic <savicaleksa83@gmail.com>
Closes: https://lore.kernel.org/all/121470f0-6c1f-418a-844c-7ec2e8a54b8e@gmail.com/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/a768e69851a07a1f4e29f270f4e2559063f07343.1701617030.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: codecs: lpass-tx-macro: set active_decimator correct default value

[ Upstream commit a2f35ed1d237c459100adb0c39bb811d7f170977 ]

The -1 value for active_decimator[dai_id] is considered as "not set",
but at probe the table is initialized a 0, this prevents enabling the
DEC0 Mixer since it will be considered as already set.

Initialize the table entries as -1 to fix tx_macro_tx_mixer_put().

Fixes: 1c6a7f5250ce ("ASoC: codecs: tx-macro: fix active_decimator array")
Fixes: c1057a08af43 ("ASoC: codecs: tx-macro: fix kcontrol put")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231116-topic-sm8x50-upstream-tx-macro-fix-active-decimator-set-v1-1-6edf402f4b6f@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (acpi_power_meter) Fix 4.29 MW bug

[ Upstream commit 1fefca6c57fb928d2131ff365270cbf863d89c88 ]

The ACPI specification says:

"If an error occurs while obtaining the meter reading or if the value
is not available then an Integer with all bits set is returned"

Since the "integer" is 32 bits in case of the ACPI power meter,
userspace will get a power reading of 2^32 * 1000 miliwatts (~4.29 MW)
in case of such an error. This was discovered due to a lm_sensors
bugreport (https://github.com/lm-sensors/lm-sensors/issues/460).
Fix this by returning -ENODATA instead.

Tested-by: <urbinek@gmail.com>
Fixes: de584afa5e18 ("hwmon driver for ACPI 4.0 power meters")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231124182747.13956-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: bcm2711-rpi-400: Fix delete-node of led_act

[ Upstream commit dc761f11af2e39119d3a7942e3d10615f3d900e7 ]

The LED ACT which is included from bcm2711-rpi-4-b doesn't exists
on the Raspberry Pi 400. So the bcm2711-rpi-400.dts tries to
use the delete-node directive in order to remove the complete
node. Unfortunately the usage get broken in commit 1156e3a78bcc
("ARM: dts: bcm283x: Move ACT LED into separate dtsi")
and now ACT and PWR LED using the same GPIO and this prevent
probing of led-gpios on Raspberry Pi 400:

leds-gpio: probe of leds failed with error -16

So fix the delete-node directive.

Fixes: 1156e3a78bcc ("ARM: dts: bcm283x: Move ACT LED into separate dtsi")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231118124252.14838-3-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: rockchip: Fix sdmmc_pwren's pinmux setting for RK3128

[ Upstream commit 0c349b5001f8bdcead844484c15a0c4dfb341157 ]

RK3128's reference design uses sdmmc_pwren pincontrol as GPIO - see [0].

Let's change it in the SoC DT as well.

[0] https://github.com/rockchip-linux/kernel/commit/8c62deaf6025

Fixes: a0201bff6259 ("ARM: dts: rockchip: add rk3128 soc dtsi")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231127184643.13314-2-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx6q: skov: fix ethernet clock regression

[ Upstream commit 6552218f4dc47ba3c6c5b58cc1e9eb208a2b438b ]

A regression was introduced in the Skov specific i.MX6 flavor
reve-mi1010ait-1cp1 device tree causing the external ethernet controller
to not being selected as the clock source for the i.MX6 ethernet MAC,
resulting in a none functional ethernet interface. The root cause is
that the ethernet clock selection is now part of the clocks node, which
is overwritten in the specific device tree and wasn't updated to contain
these ethernet clocks.

Fixes: c89614079e44 ("ARM: dts: imx6qdl-skov-cpu: configure ethernet reference clock parent")
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dt: imx93: tqma9352-mba93xxla: Fix LPUART2 pad config

[ Upstream commit 2bfba37b3d90d6d2d499d5b0dfe99c05c38b1b54 ]

LPUART2_RTS# has an external pull-down, so do not enable the internal
pull-up at the same time, use a pull-down instead.

Fixes: c982ecfa7992a ("arm64: dts: freescale: add initial device tree for MBa93xxLA SBC board")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/irdma: Fix UAF in irdma_sc_ccq_get_cqe_info()

[ Upstream commit 2b78832f50c4d711e161b166d7d8790968051546 ]

When removing the irdma driver or unplugging its aux device, the ccq
queue is released before destorying the cqp_cmpl_wq queue.
But in the window, there may still be completion events for wqes. That
will cause a UAF in irdma_sc_ccq_get_cqe_info().

[34693.333191] BUG: KASAN: use-after-free in irdma_sc_ccq_get_cqe_info+0x82f/0x8c0 [irdma]
[34693.333194] Read of size 8 at addr ffff889097f80818 by task kworker/u67:1/26327
[34693.333194]
[34693.333199] CPU: 9 PID: 26327 Comm: kworker/u67:1 Kdump: loaded Tainted: G           O     --------- -t - 4.18.0 #1
[34693.333200] Hardware name: SANGFOR Inspur/NULL, BIOS 4.1.13 08/01/2016
[34693.333211] Workqueue: cqp_cmpl_wq cqp_compl_worker [irdma]
[34693.333213] Call Trace:
[34693.333220]  dump_stack+0x71/0xab
[34693.333226]  print_address_description+0x6b/0x290
[34693.333238]  ? irdma_sc_ccq_get_cqe_info+0x82f/0x8c0 [irdma]
[34693.333240]  kasan_report+0x14a/0x2b0
[34693.333251]  irdma_sc_ccq_get_cqe_info+0x82f/0x8c0 [irdma]
[34693.333264]  ? irdma_free_cqp_request+0x151/0x1e0 [irdma]
[34693.333274]  irdma_cqp_ce_handler+0x1fb/0x3b0 [irdma]
[34693.333285]  ? irdma_ctrl_init_hw+0x2c20/0x2c20 [irdma]
[34693.333290]  ? __schedule+0x836/0x1570
[34693.333293]  ? strscpy+0x83/0x180
[34693.333296]  process_one_work+0x56a/0x11f0
[34693.333298]  worker_thread+0x8f/0xf40
[34693.333301]  ? __kthread_parkme+0x78/0xf0
[34693.333303]  ? rescuer_thread+0xc50/0xc50
[34693.333305]  kthread+0x2a0/0x390
[34693.333308]  ? kthread_destroy_worker+0x90/0x90
[34693.333310]  ret_from_fork+0x1f/0x40

Fixes: 44d9e52977a1 ("RDMA/irdma: Implement device initialization definitions")
Signed-off-by: Shifeng Li <lishifeng1992@126.com>
Link: https://lore.kernel.org/r/20231121101236.581694-1-lishifeng1992@126.com
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/bnxt_re: Correct module description string

[ Upstream commit 422b19f7f006e813ee0865aadce6a62b3c263c42 ]

The word "Driver" is repeated twice in the "modinfo bnxt_re"
output description. Fix it.

Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1700555387-6277-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-clt: Remove the warnings for req in_use check

[ Upstream commit 0c8bb6eb70ca41031f663b4481aac9ac78b53bc6 ]

As we chain the WR during write request: memory registration,
rdma write, local invalidate, if only the last WR fail to send due
to send queue overrun, the server can send back the reply, while
client mark the req->in_use to false in case of error in rtrs_clt_req
when error out from rtrs_post_rdma_write_sg.

Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality")
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20231120154146.920486-8-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-clt: Fix the max_send_wr setting

[ Upstream commit 6d09f6f7d7584e099633282ea915988914f86529 ]

For each write request, we need Request, Response Memory Registration,
Local Invalidate.

Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality")
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20231120154146.920486-7-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv: Destroy path files after making sure no IOs in-flight

[ Upstream commit c4d32e77fc1006f99eeb78417efc3d81a384072a ]

Destroying path files may lead to the freeing of rdma_stats. This creates
the following race.

An IO is in-flight, or has just passed the session state check in
process_read/process_write. The close_work gets triggered and the function
rtrs_srv_close_work() starts and does destroy path which frees the
rdma_stats. After this the function process_read/process_write resumes and
tries to update the stats through the function rtrs_srv_update_rdma_stats

This commit solves the problem by moving the destroy path function to a
later point. This point makes sure any inflights are completed. This is
done by qp drain, and waiting for all in-flights through ops_id.

Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality")
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Santosh Kumar Pradhan <santosh.pradhan@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20231120154146.920486-6-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv: Free srv_mr iu only when always_invalidate is true

[ Upstream commit 3a71cd6ca0ce33d1af019ecf1d7167406fa54400 ]

Since srv_mr->iu is allocated and used only when always_invalidate is
true, free it only when always_invalidate is true.

Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality")
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20231120154146.920486-5-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv: Check return values while processing info request

[ Upstream commit ed1e52aefa16f15dc2f04054a3baf11726a7460e ]

While processing info request, it could so happen that the srv_path goes
to CLOSING state, cause of any of the error events from RDMA. That state
change should be picked up while trying to change the state in
process_info_req, by checking the return value. In case the state change
call in process_info_req fails, we fail the processing.

We should also check the return value for rtrs_srv_path_up, since it
sends a link event to the client above, and the client can fail for any
reason.

Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality")
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20231120154146.920486-4-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-clt: Start hb after path_up

[ Upstream commit 3e44a61b5db873612e20e7b7922468d7d1ac2d22 ]

If we start hb too early, it will confuse server side to close
the session.

Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality")
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20231120154146.920486-3-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv: Do not unconditionally enable irq

[ Upstream commit 3ee7ecd712048ade6482bea4b2f3dcaf039c0348 ]

When IO is completed, rtrs can be called in softirq context,
unconditionally enabling irq could cause panic.

To be on safe side, use spin_lock_irqsave and spin_unlock_irqrestore
instread.

Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality")
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Florian-Ewald Mueller <florian-ewald.mueller@ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20231120154146.920486-2-haris.iqbal@ionos.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_sai: Fix no frame sync clock issue on i.MX8MP

[ Upstream commit 14e8442e0789598514f3c9de014950de9feda7a4 ]

On i.MX8MP, when the TERE and FSD_MSTR enabled before configuring
the word width, there will be no frame sync clock issue, because
old word width impact the generation of frame sync.

TERE enabled earlier only for i.MX8MP case for the hardware limitation,
So need to disable FSD_MSTR before configuring word width, then enable
FSD_MSTR bit for this specific case.

Fixes: 3e4a82612998 ("ASoC: fsl_sai: MCLK bind with TX/RX enable bit")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1700474735-3863-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Expand reg size of vdec node for RK3399

[ Upstream commit 35938c18291b5da7422b2fac6dac0af11aa8d0d7 ]

Expand the reg size for the vdec node to include cache/performance
registers the rkvdec driver writes to. Also add missing clocks to the
related power-domain.

Fixes: cbd7214402ec ("arm64: dts: rockchip: Define the rockchip Video Decoder node on rk3399")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20231105233630.3927502-10-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Expand reg size of vdec node for RK3328

[ Upstream commit 0b6240d697a96eaa45a2a5503a274ebb4f162fa3 ]

Expand the reg size for the vdec node to include cache/performance
registers the rkvdec driver writes to.

Fixes: 17408c9b119d ("arm64: dts: rockchip: Add vdec support for RK3328")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20231105233630.3927502-9-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/irdma: Add wait for suspend on SQD

[ Upstream commit bd6da690c27d75cae432c09162d054b34fa2156f ]

Currently, there is no wait for the QP suspend to complete on a modify
to SQD state. Add a wait, after the modify to SQD state, for the Suspend
Complete AE. While we are at it, update the suspend timeout value in
irdma_prep_tc_change to use IRDMA_EVENT_TIMEOUT_MS too.

Fixes: b48c24c2d710 ("RDMA/irdma: Implement device supported verb APIs")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/20231114170246.238-3-shiraz.saleem@intel.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/irdma: Do not modify to SQD on error

[ Upstream commit ba12ab66aa83a2340a51ad6e74b284269745138c ]

Remove the modify to SQD before going to ERROR state. It is not needed.

Fixes: b48c24c2d710 ("RDMA/irdma: Implement device supported verb APIs")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/20231114170246.238-2-shiraz.saleem@intel.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hns: Fix unnecessary err return when using invalid congest control algorithm

[ Upstream commit efb9cbf66440482ceaa90493d648226ab7ec2ebf ]

Add a default congest control algorithm so that driver won't return
an error when the configured algorithm is invalid.

Fixes: f91696f2f053 ("RDMA/hns: Support congestion control type selection according to the FW")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20231028093242.670325-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/core: Fix uninit-value access in ib_get_eth_speed()

[ Upstream commit 0550d4604e2ca4e653dc13f0c009fc42106b6bfc ]

KMSAN reported the following uninit-value access issue:

lo speed is unknown, defaulting to 1000
=====================================================
BUG: KMSAN: uninit-value in ib_get_width_and_speed drivers/infiniband/core/verbs.c:1889 [inline]
BUG: KMSAN: uninit-value in ib_get_eth_speed+0x546/0xaf0 drivers/infiniband/core/verbs.c:1998
ib_get_width_and_speed drivers/infiniband/core/verbs.c:1889 [inline]
ib_get_eth_speed+0x546/0xaf0 drivers/infiniband/core/verbs.c:1998
siw_query_port drivers/infiniband/sw/siw/siw_verbs.c:173 [inline]
siw_get_port_immutable+0x6f/0x120 drivers/infiniband/sw/siw/siw_verbs.c:203
setup_port_data drivers/infiniband/core/device.c:848 [inline]
setup_device drivers/infiniband/core/device.c:1244 [inline]
ib_register_device+0x1589/0x1df0 drivers/infiniband/core/device.c:1383
siw_device_register drivers/infiniband/sw/siw/siw_main.c:72 [inline]
siw_newlink+0x129e/0x13d0 drivers/infiniband/sw/siw/siw_main.c:490
nldev_newlink+0x8fd/0xa60 drivers/infiniband/core/nldev.c:1763
rdma_nl_rcv_skb drivers/infiniband/core/netlink.c:239 [inline]
rdma_nl_rcv+0xe8a/0x1120 drivers/infiniband/core/netlink.c:259
netlink_unicast_kernel net/netlink/af_netlink.c:1342 [inline]
netlink_unicast+0xf4b/0x1230 net/netlink/af_netlink.c:1368
netlink_sendmsg+0x1242/0x1420 net/netlink/af_netlink.c:1910
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
____sys_sendmsg+0x997/0xd60 net/socket.c:2588
___sys_sendmsg+0x271/0x3b0 net/socket.c:2642
__sys_sendmsg net/socket.c:2671 [inline]
__do_sys_sendmsg net/socket.c:2680 [inline]
__se_sys_sendmsg net/socket.c:2678 [inline]
__x64_sys_sendmsg+0x2fa/0x4a0 net/socket.c:2678
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x44/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b

Local variable lksettings created at:
ib_get_eth_speed+0x4b/0xaf0 drivers/infiniband/core/verbs.c:1974
siw_query_port drivers/infiniband/sw/siw/siw_verbs.c:173 [inline]
siw_get_port_immutable+0x6f/0x120 drivers/infiniband/sw/siw/siw_verbs.c:203

CPU: 0 PID: 11257 Comm: syz-executor.1 Not tainted 6.6.0-14500-g1c41041124bd #10
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc38 04/01/2014
=====================================================

If __ethtool_get_link_ksettings() fails, `netdev_speed` is set to the
default value, SPEED_1000. In this case, if `lanes` field of struct
ethtool_link_ksettings is not initialized, an uninitialized value is passed
to ib_get_width_and_speed(). This causes the above issue. This patch
resolves the issue by initializing `lanes` to 0.

Fixes: cb06b6b3f6cb ("RDMA/core: Get IB width and speed from netdev")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Link: https://lore.kernel.org/r/20231108143113.1360567-1-syoshida@redhat.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tee: optee: Fix supplicant based device enumeration

[ Upstream commit 7269cba53d906cf257c139d3b3a53ad272176bca ]

Currently supplicant dependent optee device enumeration only registers
devices whenever tee-supplicant is invoked for the first time. But it
forgets to remove devices when tee-supplicant daemon stops running and
closes its context gracefully. This leads to following error for fTPM
driver during reboot/shutdown:

[ 73.466791] tpm tpm0: ftpm_tee_tpm_op_send: SUBMIT_COMMAND invoke error: 0xffff3024

Fix this by adding an attribute for supplicant dependent devices so that
the user-space service can detect and detach supplicant devices before
closing the supplicant:

$ for dev in /sys/bus/tee/devices/*; do if [[ -f "$dev/need_supplicant" && -f "$dev/driver/unbind" ]]; \
then echo $(basename "$dev") > $dev/driver/unbind; fi done

Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Closes: https://github.com/OP-TEE/optee_os/issues/6094
Fixes: 5f178bb71e3a ("optee: enable support for multi-stage bus enumeration")
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jerome Forissier <jerome.forissier@linaro.org>
[jw: fixed up Date documentation]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mm/damon/sysfs: eliminate potential uninitialized variable warning

[ Upstream commit 85c2ceaafbd306814a3a4740bf4d95ac26a8b36a ]

The "err" variable is not initialized if damon_target_has_pid(ctx) is
false and sys_target->regions->nr is zero.

Link: https://lkml.kernel.org/r/739e6aaf-a634-4e33-98a8-16546379ec9f@moroto.mountain
Fixes: 0bcd216c4741 ("mm/damon/sysfs: update monitoring target regions for online input commit")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: SeongJae Park <sj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: get doorbell's absolute offset based on the db_size

[ Upstream commit 367a0af43373d4f791cc8b466a659ecf5aa52377 ]

Here, Adding db_size in byte to find the doorbell's
absolute offset for both 32-bit and 64-bit doorbell sizes.
So that doorbell offset will be aligned based on the doorbell
size.

v2:
- Addressed the review comment from Felix.
v3:
- Adding doorbell_size as parameter to get db absolute offset.
v4:
Squash the two patches into one.

Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Arvind Yadav <Arvind.Yadav@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/amdgpu/amdgpu_doorbell_mgr: Correct misdocumented param 'doorbell_index'

[ Upstream commit 04cef5f58395806294a64118cf8a39534bd032a2 ]

Fixes the following W=1 kernel build warning(s):

drivers/gpu/drm/amd/amdgpu/amdgpu_doorbell_mgr.c:123: warning: Function parameter or member 'doorbell_index' not described in 'amdgpu_doorbell_index_on_bar'
drivers/gpu/drm/amd/amdgpu/amdgpu_doorbell_mgr.c:123: warning: Excess function parameter 'db_index' description in 'amdgpu_doorbell_index_on_bar'

Reviewed-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/smc: fix missing byte order conversion in CLC handshake

[ Upstream commit c5a10397d4571bcfd4bd7ca211ee47bcb6792ec3 ]

The byte order conversions of ISM GID and DMB token are missing in
process of CLC accept and confirm. So fix it.

Fixes: 3d9725a6a133 ("net/smc: common routine for CLC accept and confirm")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://lore.kernel.org/r/1701882157-87956-1-git-send-email-guwen@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: microchip: provide a list of valid protocols for xmit handler

[ Upstream commit 1499b89289bf272fd83cb296c82fb5519d0fe93f ]

Provide a list of valid protocols for which the driver will provide
it's deferred xmit handler.

When using DSA_TAG_PROTO_KSZ8795 protocol, it does not provide a
"connect" method, therefor ksz_connect() is not allocating ksz_tagger_data.

This avoids the following null pointer dereference:
ksz_connect_tag_protocol from dsa_register_switch+0x9ac/0xee0
dsa_register_switch from ksz_switch_register+0x65c/0x828
ksz_switch_register from ksz_spi_probe+0x11c/0x168
ksz_spi_probe from spi_probe+0x84/0xa8
spi_probe from really_probe+0xc8/0x2d8

Fixes: ab32f56a4100 ("net: dsa: microchip: ptp: add packet transmission timestamping")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231206071655.1626479-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drop_monitor: Require 'CAP_SYS_ADMIN' when joining "events" group

[ Upstream commit e03781879a0d524ce3126678d50a80484a513c4b ]

The "NET_DM" generic netlink family notifies drop locations over the
"events" multicast group. This is problematic since by default generic
netlink allows non-root users to listen to these notifications.

Fix by adding a new field to the generic netlink multicast group
structure that when set prevents non-root users or root without the
'CAP_SYS_ADMIN' capability (in the user namespace owning the network
namespace) from joining the group. Set this field for the "events"
group. Use 'CAP_SYS_ADMIN' rather than 'CAP_NET_ADMIN' because of the
nature of the information that is shared over this group.

Note that the capability check in this case will always be performed
against the initial user namespace since the family is not netns aware
and only operates in the initial network namespace.

A new field is added to the structure rather than using the "flags"
field because the existing field uses uAPI flags and it is inappropriate
to add a new uAPI flag for an internal kernel check. In net-next we can
rework the "flags" field to use internal flags and fold the new field
into it. But for now, in order to reduce the amount of changes, add a
new field.

Since the information can only be consumed by root, mark the control
plane operations that start and stop the tracing as root-only using the
'GENL_ADMIN_PERM' flag.

Tested using [1].

Before:

# capsh -- -c ./dm_repo
# capsh --drop=cap_sys_admin -- -c ./dm_repo

After:

# capsh -- -c ./dm_repo
# capsh --drop=cap_sys_admin -- -c ./dm_repo
Failed to join "events" multicast group

[1]
$ cat dm.c
#include <stdio.h>
#include <netlink/genl/ctrl.h>
#include <netlink/genl/genl.h>
#include <netlink/socket.h>

int main(int argc, char **argv)
{
struct nl_sock *sk;
int grp, err;

sk = nl_socket_alloc();
if (!sk) {
fprintf(stderr, "Failed to allocate socket\n");
return -1;
}

err = genl_connect(sk);
if (err) {
fprintf(stderr, "Failed to connect socket\n");
return err;
}

grp = genl_ctrl_resolve_grp(sk, "NET_DM", "events");
if (grp < 0) {
fprintf(stderr,
"Failed to resolve \"events\" multicast group\n");
return grp;
}

err = nl_socket_add_memberships(sk, grp, NFNLGRP_NONE);
if (err) {
fprintf(stderr, "Failed to join \"events\" multicast group\n");
return err;
}

return 0;
}
$ gcc -I/usr/include/libnl3 -lnl-3 -lnl-genl-3 -o dm_repo dm.c

Fixes: 9a8afc8d3962 ("Network Drop Monitor: Adding drop monitor implementation & Netlink protocol")
Reported-by: "The UK's National Cyber Security Centre (NCSC)" <security@ncsc.gov.uk>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20231206213102.1824398-3-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

psample: Require 'CAP_NET_ADMIN' when joining "packets" group

[ Upstream commit 44ec98ea5ea9cfecd31a5c4cc124703cb5442832 ]

The "psample" generic netlink family notifies sampled packets over the
"packets" multicast group. This is problematic since by default generic
netlink allows non-root users to listen to these notifications.

Fix by marking the group with the 'GENL_UNS_ADMIN_PERM' flag. This will
prevent non-root users or root without the 'CAP_NET_ADMIN' capability
(in the user namespace owning the network namespace) from joining the
group.

Tested using [1].

Before:

# capsh -- -c ./psample_repo
# capsh --drop=cap_net_admin -- -c ./psample_repo

After:

# capsh -- -c ./psample_repo
# capsh --drop=cap_net_admin -- -c ./psample_repo
Failed to join "packets" multicast group

[1]
$ cat psample.c
#include <stdio.h>
#include <netlink/genl/ctrl.h>
#include <netlink/genl/genl.h>
#include <netlink/socket.h>

int join_grp(struct nl_sock *sk, const char *grp_name)
{
int grp, err;

grp = genl_ctrl_resolve_grp(sk, "psample", grp_name);
if (grp < 0) {
fprintf(stderr, "Failed to resolve \"%s\" multicast group\n",
grp_name);
return grp;
}

err = nl_socket_add_memberships(sk, grp, NFNLGRP_NONE);
if (err) {
fprintf(stderr, "Failed to join \"%s\" multicast group\n",
grp_name);
return err;
}

return 0;
}

int main(int argc, char **argv)
{
struct nl_sock *sk;
int err;

sk = nl_socket_alloc();
if (!sk) {
fprintf(stderr, "Failed to allocate socket\n");
return -1;
}

err = genl_connect(sk);
if (err) {
fprintf(stderr, "Failed to connect socket\n");
return err;
}

err = join_grp(sk, "config");
if (err)
return err;

err = join_grp(sk, "packets");
if (err)
return err;

return 0;
}
$ gcc -I/usr/include/libnl3 -lnl-3 -lnl-genl-3 -o psample_repo psample.c

Fixes: 6ae0a6286171 ("net: Introduce psample, a new genetlink channel for packet sampling")
Reported-by: "The UK's National Cyber Security Centre (NCSC)" <security@ncsc.gov.uk>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20231206213102.1824398-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: sockmap, updating the sg structure should also update curr

[ Upstream commit bb9aefde5bbaf6c168c77ba635c155b4980c2287 ]

Curr pointer should be updated when the sg structure is shifted.

Fixes: 7246d8ed4dcce ("bpf: helper to pop data from messages")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20231206232706.374377-3-john.fastabend@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: tls, update curr on splice as well

[ Upstream commit c5a595000e2677e865a39f249c056bc05d6e55fd ]

The curr pointer must also be updated on the splice similar to how
we do this for other copy types.

Fixes: d829e9c4112b ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reported-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20231206232706.374377-2-john.fastabend@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: mv88e6xxx: Restore USXGMII support for 6393X

[ Upstream commit 0c7ed1f9197aecada33a08b022e484a97bf584ba ]

In 4a56212774ac, USXGMII support was added for 6393X, but this was
lost in the PCS conversion (the blamed commit), most likely because
these efforts where more or less done in parallel.

Restore this feature by porting Michal's patch to fit the new
implementation.

Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Michal Smulski <michal.smulski@ooma.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: e5b732a275f5 ("net: dsa: mv88e6xxx: convert 88e639x to phylink_pcs")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20231205221359.3926018-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: do not accept ACK of bytes we never sent

[ Upstream commit 3d501dd326fb1c73f1b8206d4c6e1d7b15c07e27 ]

This patch is based on a detailed report and ideas from Yepeng Pan
and Christian Rossow.

ACK seq validation is currently following RFC 5961 5.2 guidelines:

   The ACK value is considered acceptable only if
   it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <=
   SND.NXT).  All incoming segments whose ACK value doesn't satisfy the
   above condition MUST be discarded and an ACK sent back.  It needs to
   be noted that RFC 793 on page 72 (fifth check) says: "If the ACK is a
   duplicate (SEG.ACK < SND.UNA), it can be ignored.  If the ACK
   acknowledges something not yet sent (SEG.ACK > SND.NXT) then send an
   ACK, drop the segment, and return".  The "ignored" above implies that
   the processing of the incoming data segment continues, which means
   the ACK value is treated as acceptable.  This mitigation makes the
   ACK check more stringent since any ACK < SND.UNA wouldn't be
   accepted, instead only ACKs that are in the range ((SND.UNA -
   MAX.SND.WND) <= SEG.ACK <= SND.NXT) get through.

This can be refined for new (and possibly spoofed) flows,
by not accepting ACK for bytes that were never sent.

This greatly improves TCP security at a little cost.

I added a Fixes: tag to make sure this patch will reach stable trees,
even if the 'blamed' patch was adhering to the RFC.

tp->bytes_acked was added in linux-4.2

Following packetdrill test (courtesy of Yepeng Pan) shows
the issue at hand:

0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1024) = 0

// ---------------- Handshake ------------------- //

// when window scale is set to 14 the window size can be extended to
// 65535 * (2^14) = 1073725440. Linux would accept an ACK packet
// with ack number in (Server_ISN+1-1073725440. Server_ISN+1)
// ,though this ack number acknowledges some data never
// sent by the server.

+0 < S 0:0(0) win 65535 <mss 1400,nop,wscale 14>
+0 > S. 0:0(0) ack 1 <...>
+0 < . 1:1(0) ack 1 win 65535
+0 accept(3, ..., ...) = 4

// For the established connection, we send an ACK packet,
// the ack packet uses ack number 1 - 1073725300 + 2^32,
// where 2^32 is used to wrap around.
// Note: we used 1073725300 instead of 1073725440 to avoid possible
// edge cases.
// 1 - 1073725300 + 2^32 = 3221241997

// Oops, old kernels happily accept this packet.
+0 < . 1:1001(1000) ack 3221241997 win 65535

// After the kernel fix the following will be replaced by a challenge ACK,
// and prior malicious frame would be dropped.
+0 > . 1:1(0) ack 1001

Fixes: 354e4aa391ed ("tcp: RFC 5961 5.2 Blind Data Injection Attack Mitigation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yepeng Pan <yepeng.pan@cispa.de>
Reported-by: Christian Rossow <rossow@cispa.de>
Acked-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20231205161841.2702925-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: xt_owner: Fix for unsafe access of sk->sk_socket

[ Upstream commit 7ae836a3d630e146b732fe8ef7d86b243748751f ]

A concurrently running sock_orphan() may NULL the sk_socket pointer in
between check and deref. Follow other users (like nft_meta.c for
instance) and acquire sk_callback_lock before dereferencing sk_socket.

Fixes: 0265ab44bacc ("[NETFILTER]: merge ipt_owner/ip6t_owner in xt_owner")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: validate family when identifying table via handle

[ Upstream commit f6e1532a2697b81da00bfb184e99d15e01e9d98c ]

Validate table family when looking up for it via NFTA_TABLE_HANDLE.

Fixes: 3ecbfd65f50e ("netfilter: nf_tables: allocate handle and delete objects via handle")
Reported-by: Xingyuan Mo <hdthky0@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: bail out on mismatching dynset and set expressions

[ Upstream commit 3701cd390fd731ee7ae8b8006246c8db82c72bea ]

If dynset expressions provided by userspace is larger than the declared
set expressions, then bail out.

Fixes: 48b0ae046ee9 ("netfilter: nftables: netlink support for several set element expressions")
Reported-by: Xingyuan Mo <hdthky0@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: fix 'exist' matching on bigendian arches

[ Upstream commit 63331e37fb227e796894b31d713697612c8dee7f ]

Maze reports "tcp option fastopen exists" fails to match on
OpenWrt 22.03.5, r20134-5f15225c1e (5.10.176) router.

"tcp option fastopen exists" translates to:
inet
[ exthdr load tcpopt 1b @ 34 + 0 present => reg 1 ]
[ cmp eq reg 1 0x00000001 ]

.. but existing nft userspace generates a 1-byte compare.

On LSB (x86), "*reg32 = 1" is identical to nft_reg_store8(reg32, 1), but
not on MSB, which will place the 1 last. IOW, on bigendian aches the cmp8
is awalys false.

Make sure we store this in a consistent fashion, so existing userspace
will also work on MSB (bigendian).

Regardless of this patch we can also change nft userspace to generate
'reg32 == 0' and 'reg32 != 0' instead of u8 == 0 // u8 == 1 when
adding 'option x missing/exists' expressions as well.

Fixes: 3c1fece8819e ("netfilter: nft_exthdr: Allow checking TCP option presence, too")
Fixes: b9f9a485fb0e ("netfilter: nft_exthdr: add boolean DCCP option matching")
Fixes: 055c4b34b94f ("netfilter: nft_fib: Support existence check")
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Closes: https://lore.kernel.org/netfilter-devel/CAHo-OozyEqHUjL2-ntATzeZOiuftLWZ_HU6TOM_js4qLfDEAJg@mail.gmail.com/
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: bpf: fix bad registration on nf_defrag

[ Upstream commit 1834d62ae88500f37cba4439c3237aa85242272e ]

We should pass a pointer to global_hook to the get_proto_defrag_hook()
instead of its value, since the passed value won't be updated even if
the request module was loaded successfully.

Log:

[   54.915713] nf_defrag_ipv4 has bad registration
[   54.915779] WARNING: CPU: 3 PID: 6323 at net/netfilter/nf_bpf_link.c:62 get_proto_defrag_hook+0x137/0x160
[   54.915835] CPU: 3 PID: 6323 Comm: fentry Kdump: loaded Tainted: G            E      6.7.0-rc2+ #35
[   54.915839] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
[   54.915841] RIP: 0010:get_proto_defrag_hook+0x137/0x160
[   54.915844] Code: 4f 8c e8 2c cf 68 ff 80 3d db 83 9a 01 00 0f 85 74 ff ff ff 48 89 ee 48 c7 c7 8f 12 4f 8c c6 05 c4 83 9a 01 01 e8 09 ee 5f ff <0f> 0b e9 57 ff ff ff 49 8b 3c 24 4c 63 e5 e8 36 28 6c ff 4c 89 e0
[   54.915849] RSP: 0018:ffffb676003fbdb0 EFLAGS: 00010286
[   54.915852] RAX: 0000000000000023 RBX: ffff9596503d5600 RCX: ffff95996fce08c8
[   54.915854] RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff95996fce08c0
[   54.915855] RBP: ffffffff8c4f12de R08: 0000000000000000 R09: 00000000fffeffff
[   54.915859] R10: ffffb676003fbc70 R11: ffffffff8d363ae8 R12: 0000000000000000
[   54.915861] R13: ffffffff8e1f75c0 R14: ffffb676003c9000 R15: 00007ffd15e78ef0
[   54.915864] FS:  00007fb6e9cab740(0000) GS:ffff95996fcc0000(0000) knlGS:0000000000000000
[   54.915867] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   54.915868] CR2: 00007ffd15e75c40 CR3: 0000000101e62006 CR4: 0000000000360ef0
[   54.915870] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   54.915871] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   54.915873] Call Trace:
[   54.915891]  <TASK>
[   54.915894]  ? __warn+0x84/0x140
[   54.915905]  ? get_proto_defrag_hook+0x137/0x160
[   54.915908]  ? __report_bug+0xea/0x100
[   54.915925]  ? report_bug+0x2b/0x80
[   54.915928]  ? handle_bug+0x3c/0x70
[   54.915939]  ? exc_invalid_op+0x18/0x70
[   54.915942]  ? asm_exc_invalid_op+0x1a/0x20
[   54.915948]  ? get_proto_defrag_hook+0x137/0x160
[   54.915950]  bpf_nf_link_attach+0x1eb/0x240
[   54.915953]  link_create+0x173/0x290
[   54.915969]  __sys_bpf+0x588/0x8f0
[   54.915974]  __x64_sys_bpf+0x20/0x30
[   54.915977]  do_syscall_64+0x45/0xf0
[   54.915989]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[   54.915998] RIP: 0033:0x7fb6e9daa51d
[   54.916001] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 2b 89 0c 00 f7 d8 64 89 01 48
[   54.916003] RSP: 002b:00007ffd15e78ed8 EFLAGS: 00000246 ORIG_RAX: 0000000000000141
[   54.916006] RAX: ffffffffffffffda RBX: 00007ffd15e78fc0 RCX: 00007fb6e9daa51d
[   54.916007] RDX: 0000000000000040 RSI: 00007ffd15e78ef0 RDI: 000000000000001c
[   54.916009] RBP: 000000000000002d R08: 00007fb6e9e73a60 R09: 0000000000000001
[   54.916010] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000006
[   54.916012] R13: 0000000000000006 R14: 0000000000000000 R15: 0000000000000000
[   54.916014]  </TASK>
[   54.916015] ---[ end trace 0000000000000000 ]---

Fixes: 91721c2d02d3 ("netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Daniel Xu <dxu@dxuuu.xyz>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dt-bindings: interrupt-controller: Allow #power-domain-cells

[ Upstream commit c0a2755aced969e0125fd68ccd95269b28d8913a ]

MPM provides a single genpd. Allow #power-domain-cells = <0>.

Fixes: 54fc9851c0e0 ("dt-bindings: interrupt-controller: Add Qualcomm MPM support")
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231129-topic-mpmbindingspd-v2-1-acbe909ceee1@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Update Tx link register range

[ Upstream commit 7336fc196748f82646b630d5a2e9d283e200b988 ]

On new silicons the TX channels for transmit level has increased.
This patch fixes the respective register offset range to
configure the newly added channels.

Fixes: b279bbb3314e ("octeontx2-af: NIX Tx scheduler queue config support")
Signed-off-by: Rahul Bhansali <rbhansali@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Add missing mcs flr handler call

[ Upstream commit d431abd0a9aa27be379fb5f8304062071b0f5a7e ]

If mcs resources are attached to PF/VF. These resources need
to be freed on FLR. This patch add missing mcs flr call on PF FLR.

Fixes: bd69476e86fc ("octeontx2-af: cn10k: mcs: Install a default TCAM for normal traffic")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Fix mcs stats register address

[ Upstream commit 3ba98a8c6f8ceb4e01a78f973d8d9017020bbd57 ]

This patch adds the miss mcs stats register
for mcs supported platforms.

Fixes: 9312150af8da ("octeontx2-af: cn10k: mcs: Support for stats collection")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Fix mcs sa cam entries size

[ Upstream commit 9723b2cca1f0e980c53156b52ea73b93966b3c8a ]

On latest silicon versions SA cam entries increased to 256.
This patch fixes the datatype of sa_entries in mcs_hw_info
struct to u16 to hold 256 entries.

Fixes: 080bbd19c9dd ("octeontx2-af: cn10k: mcs: Add mailboxes for port related operations")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Adjust Tx credits when MCS external bypass is disabled

[ Upstream commit dca6fa8644b89f54345e55501b1419316ba5cb29 ]

When MCS external bypass is disabled, MCS returns additional
2 credits(32B) for every packet Tx'ed on LMAC. To account for
these extra credits, NIX_AF_TX_LINKX_NORM_CREDIT.CC_MCS_CNT
needs to be configured as otherwise NIX Tx credits would overflow
and will never be returned to idle state credit count
causing issues with credit control and MTU change.

This patch fixes the same by configuring CC_MCS_CNT at probe
time for MCS enabled SoC's

Fixes: bd69476e86fc ("octeontx2-af: cn10k: mcs: Install a default TCAM for normal traffic")
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns: fix fake link up on xge port

[ Upstream commit f708aba40f9c1eeb9c7e93ed4863b5f85b09b288 ]

If a xge port just connect with an optical module and no fiber,
it may have a fake link up because there may be interference on
the hardware. This patch adds an anti-shake to avoid the problem.
And the time of anti-shake is base on tests.

Fixes: b917078c1c10 ("net: hns: Add ACPI support to check SFP present")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns: fix wrong head when modify the tx feature when sending packets

[ Upstream commit 84757d0839451b20b11e993128f0a77393ca50c1 ]

Upon changing the tx feature, the hns driver will modify the
maybe_stop_tx() and fill_desc() functions, if the modify happens
during packet sending, will cause the hardware and software
pointers do not match, and the port can not work anymore.

This patch deletes the maybe_stop_tx() and fill_desc() functions
modification when setting tx feature, and use the skb_is_gro()
to determine which functions to use in the tx path.

Fixes: 38f616da1c28 ("net:hns: Add support of ethtool TSO set option for Hip06 in HNS")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: atlantic: Fix NULL dereference of skb pointer in

[ Upstream commit cbe860be36095e68e4e5561ab43610982fb429fd ]

If is_ptp_ring == true in the loop of __aq_ring_xdp_clean function,
then a timestamp is stored from a packet in a field of skb object,
which is not allocated at the moment of the call (skb == NULL).

Generalize aq_ptp_extract_ts and other affected functions so they don't
work with struct sk_buff*, but with struct skb_shared_hwtstamps*.

Found by Linux Verification Center (linuxtesting.org) with SVACE

Fixes: 26efaef759a1 ("net: atlantic: Implement xdp data plane")
Signed-off-by: Daniil Maximov <daniil31415it@gmail.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20231204085810.1681386-1-daniil31415it@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv4: ip_gre: Avoid skb_pull() failure in ipgre_xmit()

[ Upstream commit 80d875cfc9d3711a029f234ef7d680db79e8fa4b ]

In ipgre_xmit(), skb_pull() may fail even if pskb_inet_may_pull() returns
true. For example, applications can use PF_PACKET to create a malformed
packet with no IP header. This type of packet causes a problem such as
uninit-value access.

This patch ensures that skb_pull() can pull the required size by checking
the skb with pskb_network_may_pull() before skb_pull().

Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20231202161441.221135-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ionic: Fix dim work handling in split interrupt mode

[ Upstream commit 4115ba677c35f694b62298e55f0e04ce84eed469 ]

Currently ionic_dim_work() is incorrect when in
split interrupt mode. This is because the interrupt
rate is only being changed for the Rx side even for
dim running on Tx. Fix this by using the qcq from
the container_of macro. Also, introduce some local
variables for a bit of cleanup.

Fixes: a6ff85e0a2d9 ("ionic: remove intr coalesce update from napi")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231204192234.21017-3-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ionic: fix snprintf format length warning

[ Upstream commit 0ceb3860a67652f9d36dfdecfcd2cb3eb2f4537d ]

Our friendly kernel test robot has reminded us that with a new
check we have a warning about a potential string truncation.
In this case it really doesn't hurt anything, but it is worth
addressing especially since there really is no reason to reserve
so many bytes for our queue names. It seems that cutting the
queue name buffer length in half stops the complaint.

Fixes: c06107cabea3 ("ionic: more ionic name tweaks")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311300201.lO8v7mKU-lkp@intel.com/
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231204192234.21017-2-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: fix mid stream window clamp.

[ Upstream commit 58d3aade20cdddbac6c9707ac0f3f5f8c1278b74 ]

After the blamed commit below, if the user-space application performs
window clamping when tp->rcv_wnd is 0, the TCP socket will never be
able to announce a non 0 receive window, even after completely emptying
the receive buffer and re-setting the window clamp to higher values.

Refactor tcp_set_window_clamp() to address the issue: when the user
decreases the current clamp value, set rcv_ssthresh according to the
same logic used at buffer initialization, but ensuring reserved mem
provisioning.

To avoid code duplication factor-out the relevant bits from
tcp_adjust_rcv_ssthresh() in a new helper and reuse it in the above
scenario.

When increasing the clamp value, give the rcv_ssthresh a chance to grow
according to previously implemented heuristic.

Fixes: 3aa7857fe1d7 ("tcp: enable mid stream window clamp")
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Reported-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/705dad54e6e6e9a010e571bf58e0b35a8ae70503.1701706073.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: bnxt: fix a potential use-after-free in bnxt_init_tc

[ Upstream commit d007caaaf052f82ca2340d4c7b32d04a3f5dbf3f ]

When flow_indr_dev_register() fails, bnxt_init_tc will free
bp->tc_info through kfree(). However, the caller function
bnxt_init_one() will ignore this failure and call
bnxt_shutdown_tc() on failure of bnxt_dl_register(), where
a use-after-free happens. Fix this issue by setting
bp->tc_info to NULL after kfree().

Fixes: 627c89d00fb9 ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://lore.kernel.org/r/20231204024004.8245-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iavf: validate tx_coalesce_usecs even if rx_coalesce_usecs is zero

[ Upstream commit a206d9959f5ccd0fb2d54a997c993947ae0e881c ]

In __iavf_set_coalesce, the driver checks both ec->rx_coalesce_usecs and
ec->tx_coalesce_usecs for validity. It does this via a chain if if/else-if
blocks. If every single branch of the series of if statements exited, this
would be fine. However, the rx_coalesce_usecs is checked against zero to
print an informative message if use_adaptive_rx_coalesce is enabled. If
this check is true, it short circuits the entire chain of statements,
preventing validation of the tx_coalesce_usecs field.

Indeed, since commit e792779e6b63 ("iavf: Prevent changing static ITR
values if adaptive moderation is on") the iavf driver actually rejects any
change to the tx_coalesce_usecs or rx_coalesce_usecs when
use_adaptive_tx_coalesce or use_adaptive_rx_coalesce is enabled, making
this checking a bit redundant.

Fix this error by removing the unnecessary and redundant checks for
use_adaptive_rx_coalesce and use_adaptive_tx_coalesce. Since zero is a
valid value, and since the tx_coalesce_usecs and rx_coalesce_usecs fields
are already unsigned, remove the minimum value check. This allows assigning
an ITR value ranging from 0-8160 as described by the printed message.

Fixes: 65e87c0398f5 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: Fix unexpected MFS warning message

[ Upstream commit 7d9f22b3d3ef379ed05bd3f3e2de83dfa8da8258 ]

Commit 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set") added
a warning message that reports unexpected size of port's MFS (max
frame size) value. This message use for the port number local
variable 'i' that is wrong.
In i40e_probe() this 'i' variable is used only to iterate VSIs
to find FDIR VSI:

<code>
...
/* if FDIR VSI was set up, start it now */
        for (i = 0; i < pf->num_alloc_vsi; i++) {
                if (pf->vsi[i] && pf->vsi[i]->type == I40E_VSI_FDIR) {
                        i40e_vsi_open(pf->vsi[i]);
                        break;
                }
        }
...
</code>

So the warning message use for the port number index of FDIR VSI
if this exists or pf->num_alloc_vsi if not.

Fix the message by using 'pf->hw.port' for the port number.

Fixes: 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: Restore fix disabling RX VLAN filtering

[ Upstream commit 4e7f0087b058cc3cab8f3c32141b51aa5457d298 ]

Fix setting dis_rx_filtering depending on whether port vlan is being
turned on or off. This was originally fixed in commit c793f8ea15e3 ("ice:
Fix disabling Rx VLAN filtering with port VLAN enabled"), but while
refactoring ice_vf_vsi_init_vlan_ops(), the fix has been lost. Restore the
fix along with the original comment from that change.

Also delete duplicate lines in ice_port_vlan_on().

Fixes: 2946204b3fa8 ("ice: implement bridge port vlan")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: fix a use-after-free in rvu_npa_register_reporters

[ Upstream commit 3c91c909f13f0c32b0d54d75c3f798479b1a84f5 ]

The rvu_dl will be freed in rvu_npa_health_reporters_destroy(rvu_dl)
after the create_workqueue fails, and after that free, the rvu_dl will
be translate back through rvu_npa_health_reporters_create,
rvu_health_reporters_create, and rvu_register_dl. Finally it goes to the
err_dl_health label, being freed again in
rvu_health_reporters_destroy(rvu) by rvu_npa_health_reporters_destroy.
In the second calls of rvu_npa_health_reporters_destroy, however,
it uses rvu_dl->rvu_npa_health_reporter, which is already freed at
the end of rvu_npa_health_reporters_destroy in the first call.

So this patch prevents the first destroy by instantly returning -ENONMEN
when create_workqueue fails. In addition, since the failure of
create_workqueue is the only entrence of label err, it has been
integrated into the error-handling path of create_workqueue.

Fixes: f1168d1e207c ("octeontx2-af: Add devlink health reporters for NPA")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Link: https://lore.kernel.org/r/20231202095902.3264863-1-alexious@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xsk: Skip polling event check for unbound socket

[ Upstream commit e4d008d49a7135214e0ee70537405b6a069e3a3f ]

In xsk_poll(), checking available events and setting mask bits should
be executed only when a socket has been bound. Setting mask bits for
unbound socket is meaningless.

Currently, it checks events even when xsk_check_common() failed.
To prevent this, we move goto location (skip_tx) after that checking.

Fixes: 1596dae2f17e ("xsk: check IFF_UP earlier in Tx path")
Signed-off-by: Yewon Choi <woni9911@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20231201061048.GA1510@libra05
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: fix FPE events losing

[ Upstream commit 37e4b8df27bc68340f3fc80dbb27e3549c7f881c ]

The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.

Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-pf: consider both Rx and Tx packet stats for adaptive interrupt coalescing

[ Upstream commit adbf100fc47001c93d7e513ecac6fd6e04d5b4a1 ]

The current adaptive interrupt coalescing code updates only rx
packet stats for dim algorithm. This patch also updates tx packet
stats which will be useful when there is only tx traffic.
Also moved configuring hardware adaptive interrupt setting to
driver dim callback.

Fixes: 6e144b47f560 ("octeontx2-pf: Add support for adaptive interrupt coalescing")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231201053330.3903694-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arcnet: restoring support for multiple Sohard Arcnet cards

[ Upstream commit 6b17a597fc2f13aaaa0a2780eb7edb9ae7ac9aea ]

Probe of Sohard Arcnet cards fails,
if 2 or more cards are installed in a system.
See kernel log:
[    2.759203] arcnet: arcnet loaded
[    2.763648] arcnet:com20020: COM20020 chipset support (by David Woodhouse et al.)
[    2.770585] arcnet:com20020_pci: COM20020 PCI support
[    2.772295] com20020 0000:02:00.0: enabling device (0000 -> 0003)
[    2.772354] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[    3.071301] com20020 0000:02:00.0 arc0-0 (uninitialized): PCI COM20020: station FFh found at F080h, IRQ 101.
[    3.071305] com20020 0000:02:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[    3.071534] com20020 0000:07:00.0: enabling device (0000 -> 0003)
[    3.071581] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[    3.369501] com20020 0000:07:00.0: Led pci:green:tx:0-0 renamed to pci:green:tx:0-0_1 due to name collision
[    3.369535] com20020 0000:07:00.0: Led pci:red:recon:0-0 renamed to pci:red:recon:0-0_1 due to name collision
[    3.370586] com20020 0000:07:00.0 arc0-0 (uninitialized): PCI COM20020: station E1h found at C000h, IRQ 35.
[    3.370589] com20020 0000:07:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[    3.370608] com20020: probe of 0000:07:00.0 failed with error -5

commit 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support")
changes the device name of all COM20020 based PCI cards,
even if only some cards support this:
snprintf(dev->name, sizeof(dev->name), "arc%d-%d", dev->dev_id, i);

The error happens because all Sohard Arcnet cards would be called arc0-0,
since the Sohard Arcnet cards don't have a PLX rotary coder.
I.e. EAE Arcnet cards have a PLX rotary coder,
which sets the first decimal, ensuring unique devices names.

This patch adds two new card feature flags to indicate
which cards support LEDs and the PLX rotary coder.
For EAE based cards the names still depend on the PLX rotary coder
(untested, since missing EAE hardware).
For Sohard based cards, this patch will result in devices
being called arc0, arc1, ... (tested).

Signed-off-by: Thomas Reichinger <thomas.reichinger@sohard.de>
Fixes: 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support")
Link: https://lore.kernel.org/r/20231130113503.6812-1-thomas.reichinger@sohard.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/mellanox: Check devm_hwmon_device_register_with_groups() return value

[ Upstream commit 3494a594315b56516988afb6854d75dee5b501db ]

devm_hwmon_device_register_with_groups() returns an error pointer upon
failure. Check its return value for errors.

Compile-tested only.

Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Suggested-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20231201055447.2356001-1-chentao@kylinos.cn
[ij: split the change into two]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/mellanox: Add null pointer checks for devm_kasprintf()

[ Upstream commit 2c7c857f5fed997be93047d2de853d7f10c8defe ]

devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.

Compile-tested only.

Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Suggested-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20231201055447.2356001-1-chentao@kylinos.cn
[ij: split the change into two]
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxbf-bootctl: correctly identify secure boot with development keys

[ Upstream commit d4eef75279f5e9d594f5785502038c763ce42268 ]

The secure boot state of the BlueField SoC is represented by two bits:
                0 = production state
                1 = secure boot enabled
                2 = non-secure (secure boot disabled)
                3 = RMA state
There is also a single bit to indicate whether production keys or
development keys are being used when secure boot is enabled.
This single bit (specified by MLXBF_BOOTCTL_SB_DEV_MASK) only has
meaning if secure boot state equals 1 (secure boot enabled).

The secure boot states are as follows:
- “GA secured” is when secure boot is enabled with official production keys.
- “Secured (development)” is when secure boot is enabled with development keys.

Without this fix “GA Secured” is displayed on development cards which is
misleading. This patch updates the logic in "lifecycle_state_show()" to
handle the case where the SoC is configured for secure boot and is using
development keys.

Fixes: 79e29cb8fbc5c ("platform/mellanox: Add bootctl driver for Mellanox BlueField Soc")
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20231130183515.17214-1-davthompson@nvidia.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

r8152: Add RTL8152_INACCESSIBLE to r8153_aldps_en()

[ Upstream commit 79321a793945fdbff2f405f84712d0ab81bed287 ]

Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_aldps_en().

Fixes: 4214cc550bf9 ("r8152: check if disabling ALDPS is finished")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

r8152: Add RTL8152_INACCESSIBLE to r8153_pre_firmware_1()

[ Upstream commit 8c53a7bd706535a9cf4e2ec3a4e8d61d46353ca0 ]

Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().

Fixes: 9370f2d05a2a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

r8152: Add RTL8152_INACCESSIBLE to r8156b_wait_loading_flash()

[ Upstream commit 8a67b47fced9f6a84101eb9ec5ce4c7d64204bc7 ]

Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().

Fixes: 195aae321c82 ("r8152: support new chips")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

r8152: Add RTL8152_INACCESSIBLE checks to more loops

[ Upstream commit 32a574c7e2685aa8138754d4d755f9246cc6bd48 ]

Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.

All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33af4 ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")

Fixes: ac718b69301c ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

r8152: Hold the rtnl_lock for all of reset

[ Upstream commit e62adaeecdc6a1e8ae86e7f3f9f8223a3ede94f5 ]

As of commit d9962b0d4202 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
  that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
  (including usb_submit_urb() returning an error).

In that case:
* Since the USB reset is perform in a separate thread asynchronously,
  it can run at anytime USB device lock is not held - even before
  rtl8152_open() has exited with an error and caused __dev_open() to
  clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
  true (since __LINK_STATE_START wasn't cleared) so it won't exit
  early.
* rtl8152_pre_reset() will then hang in napi_disable() because
  napi_enable() was never called.

We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.

Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.

Fixes: d9962b0d4202 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hv_netvsc: rndis_filter needs to select NLS

[ Upstream commit 6c89f49964375c904cea33c0247467873f4daf2c ]

rndis_filter uses utf8s_to_utf16s() which is provided by setting
NLS, so select NLS to fix the build error:

ERROR: modpost: "utf8s_to_utf16s" [drivers/net/hyperv/hv_netvsc.ko] undefined!

Fixes: 1ce09e899d28 ("hyperv: Add support for setting MAC from within guests")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20231130055853.19069-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Fix a verifier bug due to incorrect branch offset comparison with cpu=v4

[ Upstream commit dfce9cb3140592b886838e06f3e0c25fea2a9cae ]

Bpf cpu=v4 support is introduced in [1] and Commit 4cd58e9af8b9
("bpf: Support new 32bit offset jmp instruction") added support for new
32bit offset jmp instruction. Unfortunately, in function
bpf_adj_delta_to_off(), for new branch insn with 32bit offset, the offset
(plus/minor a small delta) compares to 16-bit offset bound
[S16_MIN, S16_MAX], which caused the following verification failure:
  $ ./test_progs-cpuv4 -t verif_scale_pyperf180
  ...
  insn 10 cannot be patched due to 16-bit range
  ...
  libbpf: failed to load object 'pyperf180.bpf.o'
  scale_test:FAIL:expect_success unexpected error: -12 (errno 12)
  #405     verif_scale_pyperf180:FAIL

Note that due to recent llvm18 development, the patch [2] (already applied
in bpf-next) needs to be applied to bpf tree for testing purpose.

The fix is rather simple. For 32bit offset branch insn, the adjusted
offset compares to [S32_MIN, S32_MAX] and then verification succeeded.

  [1] https://lore.kernel.org/all/20230728011143.3710005-1-yonghong.song@linux.dev
  [2] https://lore.kernel.org/bpf/20231110193644.3130906-1-yonghong.song@linux.dev

Fixes: 4cd58e9af8b9 ("bpf: Support new 32bit offset jmp instruction")
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231201024640.3417057-1-yonghong.song@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: Check return value of nix_get_nixlf before using nixlf

[ Upstream commit 830139e7b6911266a84a77e1f18abf758995cc89 ]

If a NIXLF is not attached to a PF/VF device then
nix_get_nixlf function fails and returns proper error
code. But npc_get_default_entry_action does not check it
and uses garbage value in subsequent calls. Fix this
by cheking the return value of nix_get_nixlf.

Fixes: 967db3529eca ("octeontx2-af: add support for multicast/promisc packet replication feature")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-pf: Add missing mutex lock in otx2_get_pauseparam

[ Upstream commit 9572c949385aa2ef10368287c439bcb7935137c8 ]

All the mailbox messages sent to AF needs to be guarded
by mutex lock. Add the missing lock in otx2_get_pauseparam
function.

Fixes: 75f36270990c ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>