Priyanka Jain [Wed, 28 Nov 2018 09:56:46 +0000 (09:56 +0000)]
armv8: lx2160a: Update CONFIG_SYS_FSL_PEBUF_BASE
As per hardware documentation,
CONFIG_SYS_FSL_PEBUF_BASE for lx2160a is 0x1c00000000
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Tom Rini [Tue, 19 Feb 2019 03:12:59 +0000 (22:12 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- Misc Gen5 fixes
- stratix10 bugfix
- dwmmc bugfix
Tom Rini [Tue, 19 Feb 2019 02:36:39 +0000 (21:36 -0500)]
Prepare v2019.04-rc2
Signed-off-by: Tom Rini <trini@konsulko.com>
Jean-Jacques Hiblot [Fri, 8 Feb 2019 09:55:06 +0000 (10:55 +0100)]
configs: Enable CONFIG_BLK in am57xx_evm and am57xx_hs_evm
Enable CONFIG_DM_SCSI and CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Jean-Jacques Hiblot [Fri, 8 Feb 2019 09:55:05 +0000 (10:55 +0100)]
configs: k2g_evm: Enable CONFIG_BLK
CONFIG_BLK can be safely enabled as DM_MMC and DM_USB are already enabled.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Alexander Graf [Thu, 14 Feb 2019 13:35:17 +0000 (14:35 +0100)]
efi_loader: Swap roles with Heinrich
Heinrich is going to take over maintainership of the efi_loader tree
going forward.
To ensure that I will still receive review mails at least, add me as
reviewer with a stable email address.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Alexander Graf [Thu, 14 Feb 2019 13:37:59 +0000 (14:37 +0100)]
rpi: Make Matthias maintainer
Matthias Brugger agreed to take over maintainership from me for the
Raspberry Pi tree. Add him to the MAINTAINERS file instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Hannes Schmelzer [Fri, 15 Feb 2019 10:15:05 +0000 (11:15 +0100)]
board/BuR/brppt1: fix ethernet support on brppt1 boards
The commit
1bac199e8c87 ("configs: Resync with savedefconfig")
did remove ethernet driver from following boards defconfig:
- brppt1_mmc
- brppt1_nand
- brppt1_spi
With this commit we add ethernet and responsible phy support again.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tom Rini [Mon, 18 Feb 2019 20:48:01 +0000 (15:48 -0500)]
Merge tag 'efi-2019-04-rc2' of https://github.com/xypron2/u-boot
The patches fix multiple errors. Mentionable are:
- EFI unit tests (bootefi selftest) can run on i386.
- `make tests` executes the Unicode unit tests.
The LoadImage patch is preparing for further rework to be delivered
in v2019.07.
Ang, Chee Hong [Mon, 18 Feb 2019 04:07:50 +0000 (20:07 -0800)]
ARM: socfpga: stratix10: Return valid error code from FPGA driver
This patch prevent the Stratix 10 FPGA driver incorrectly return the
transaction ID as the mailbox error code. It should always return the
actual mailbox error code from SDM firmware.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Ley Foon Tan [Thu, 20 Dec 2018 09:55:41 +0000 (17:55 +0800)]
mmc: dwmmc: Poll for iDMAC TX/RX interrupt
Poll for iDMAC TX/RX interrupt before disable DMA.
This to prevent disable DMA before data is transfer
completed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Simon Goldschmidt [Sun, 13 Jan 2019 18:58:42 +0000 (19:58 +0100)]
arm: socfpga: gen5: remove hacked ETH RST handling
The 'dwmac_socfpga' ETH driver can now get the MACs out of reset
via the socfpga reset driver and can set PHY mode via syscon.
This means we can now remove the ad-hoc code to do this from
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Simon Goldschmidt [Sun, 13 Jan 2019 18:58:41 +0000 (19:58 +0100)]
arm: socfpga: gen5 enable designware_socfpga
Enable the socfpga specific designware ethernet driver by default for
socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a
MACH_SOCFPGA config.
This is required to remove the hacky reset and phy mode handling in
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Simon Goldschmidt [Sun, 13 Jan 2019 18:58:40 +0000 (19:58 +0100)]
net: designware: socfpga: adapt to Gen5
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tom Rini [Sat, 16 Feb 2019 23:10:53 +0000 (18:10 -0500)]
Merge tag 'video-for-2019.04-rc2' of git://git.denx.de/u-boot-video
- sunxi display DDC probe fallback
- support 24bpp BMP files on 16bpp displays
Tom Rini [Sat, 16 Feb 2019 22:05:51 +0000 (17:05 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
- Various MMC fixes
Marek Vasut [Thu, 14 Feb 2019 14:16:15 +0000 (15:16 +0100)]
mmc: tmio: sdhi: Configure DT2FF register for HS400 mode
The DT2FF register must be configured differently for HS400 mode
and for HS200/SDR104 mode. Configure the DT2FF register according
to the recommended datasheet settings for each mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Marek Vasut [Thu, 14 Feb 2019 14:16:24 +0000 (15:16 +0100)]
mmc: tmio: Configure HOST_MODE WMODE according to bus width
Set the HOST_MODE register WMODE bit according to the SDHI bus width,
that is 0 for 64bit bus and 1 for 16/32bit bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Marek Vasut [Tue, 29 Jan 2019 03:45:51 +0000 (04:45 +0100)]
mmc: Downgrade SD/MMC from UHS/HS200/HS400 modes before boot
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt [Sat, 16 Feb 2019 14:36:33 +0000 (15:36 +0100)]
efi_loader: do not miss last relocation block
If the last block in the relocation table contains only a single
relocation, the current coding ignores it.
Fix the determination of the end of the relocation table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 16 Feb 2019 14:22:13 +0000 (15:22 +0100)]
efi_loader: documentation of image loader
- Add missing function descriptions.
- Update existing function descriptions to match Sphinx style.
- Add lib/efi_loader/efi_image_loader.c to the input files for Sphinx
generated documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 12 Jan 2019 13:42:40 +0000 (14:42 +0100)]
efi_loader: clean up bootefi_test_prepare()
Free resources upon failure.
Correct the function description.
As there is no need for any special address in the dummy memory device
path passed via the EFI_LOADED_IMAGE_PROTOCOL simply use 0 as address.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 9 Feb 2019 13:10:39 +0000 (14:10 +0100)]
efi_loader: fix EFI entry counting
`bootefi selftest` fails on qemu-x86_defconfig if efi_selftest() is not
invoked using EFI_CALL().
Likewise we call the entry point of EFI payloads with
EFI_CALL(efi_start_image()).
entry_count indicates if we are in U-Boot (1) or in EFI payload code (0).
As we start in U-Boot code the initial value has to be 1.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 26 Dec 2018 12:28:09 +0000 (13:28 +0100)]
efi_loader: use efi_start_image() for bootefi
Remove the duplicate code in efi_do_enter() and use efi_start_image() to
start the image invoked by the bootefi command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 26 Dec 2018 11:49:09 +0000 (12:49 +0100)]
efi_loader: set entry point in efi_load_pe()
Up to now efi_load_pe() returns the entry point or NULL in case of an
error. This does not allow to return correct error codes from LoadImage().
Let efi_load_pe() return a status code and fill in the entry point in the
corresponding field of the image object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 24 Dec 2018 08:19:07 +0000 (09:19 +0100)]
efi_loader: LoadImage: always allocate new pages
If we want to properly unload images in Exit() the memory should always be
allocated in the same way. As we allocate memory when reading from file we
should do the same when the original image is in memory.
A further patch will be needed to free the memory when Exit() is called.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 6 Feb 2019 18:41:29 +0000 (19:41 +0100)]
efi_loader: error handling in efi_setup_loaded_image()
In case of an error we should set the returned pointers to NULL. This
ensures that an illegal free does not occur even if the caller calls
free() for the handles.
If protocols cannot be installed, release all resources.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Fri, 15 Feb 2019 22:12:50 +0000 (23:12 +0100)]
test: adjust names of Unicode test functions
In test/py/conftest.py the assumption is made that for if a test is called
with `ut unicode` the test function name starts with 'unicode_test_'. As
the Unicode tests did not follow this naming scheme they were not executed
by `make tests`.
Rename the Unicode test functions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Fri, 15 Feb 2019 21:20:53 +0000 (22:20 +0100)]
lib/vsprintf: print '?' for illegal Unicode sequence
Commit
0e66c10a7d80 ("lib: vsprintf: avoid overflow printing UTF16
strings") broke the Unicode unit tests: an illegal UTF16 code point
should be printed as '?'.
Fixes:
0e66c10a7d80 ("lib: vsprintf: avoid overflow printing UTF16 strings")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Wed, 9 Jan 2019 18:04:14 +0000 (19:04 +0100)]
efi_selftest: LoadImage from file device path
Provide a unit test that calls LoadImage() with a file device path and
executes the application via StartImage().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 4 Feb 2019 20:24:35 +0000 (21:24 +0100)]
efi_loader: comments for efi_file_from_path()
Add more comments for efi_file_from_path().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 4 Feb 2019 11:49:43 +0000 (12:49 +0100)]
efi_loader: efi_dp_split_file_path() error handling
If the path passed to efi_dp_split_file_path() does not contain a
reference to a file it returns EFI_OUT_OF_RESOURCES. This does not properly
indicate the kind of the problem that occurred. Return
EFI_INVALID_PARAMETER instead.
Update function description.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 12 Feb 2019 20:38:02 +0000 (21:38 +0100)]
efi_selftest: fix memory allocation in HII tests
In efi_selftest we are in EFI land. We cannot call U-Boot library
functions malloc() and free() but should use the boot time services
instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Tue, 12 Feb 2019 20:50:45 +0000 (21:50 +0100)]
efi_selftest: do not use efi_free_pool()
In efi_selftest we are in EFI land. We should not use U-Boot library
functions but boot time services for memory management.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tom Rini [Sat, 16 Feb 2019 13:31:05 +0000 (08:31 -0500)]
Merge tag 'u-boot-imx-2019-02-16' of git://git.denx.de/u-boot-imx
u-boot-imx-2019-02-16
---------------------
- vhybrid: add calibration
- gw_ventana: fixes
- Improve documentation for Secure Boot (HABv4)
- Fix Marvell Switch
- MX6 Sabre, switch to DM
- Fixes for NAND
Tom Rini [Sat, 16 Feb 2019 02:21:28 +0000 (21:21 -0500)]
Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2019.04-rc2
xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs
i2c:
- Remove !DM_I2C zynq driver
versal:
- Enable some more features
- Add mini configurations
Tom Rini [Sat, 16 Feb 2019 01:10:15 +0000 (20:10 -0500)]
Merge tag '2019.01-next' of https://github.com/mbgg/u-boot
- add compute module 3+
- fix 64 bit warning in bmp command
Max Krummenacher [Fri, 1 Feb 2019 15:04:51 +0000 (16:04 +0100)]
imx: cpu.c: give access to reset cause in spl
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Max Krummenacher [Fri, 1 Feb 2019 15:04:50 +0000 (16:04 +0100)]
imx: serial_mxc: disable ri and dcd irq in dte mode
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits to prevent an interrupt storm when Linux enables
the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Marcel Ziswiler [Fri, 1 Feb 2019 15:04:49 +0000 (16:04 +0100)]
ARM: dts: i.MX6Q, i.MX6QDL: fix address/size-cells warnings
This fixes the following warnings:
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/clocks: unnecessary #address-cells/#size-cells without "ranges" or
child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/aips-bus@
02100000/mipi@
021e0000: unnecessary #address-cells/
#size-cells without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02400000/port@2: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02400000/port@3: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02800000/port@2: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
arch/arm/dts/imx6-apalis.dtb: Warning (avoid_unnecessary_addr_size):
/soc/ipu@
02800000/port@3: unnecessary #address-cells/#size-cells
without "ranges" or child "reg" property
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tim Harvey [Mon, 4 Feb 2019 21:11:00 +0000 (13:11 -0800)]
imx: ventana: fix usage of dt paths with leading 0s (Linux 4.15+)
device-tree paths should never be used that reference node addresses
making an assumption about leading zeros. They should not be there per
the device-tree specification however they have been there until Linux
4.15 when they were removed via kernel commit
8dccafaa281aa1d240a58bbcdff338aec114a021.
This fixes various issues which will occur when using Linux 4.15+
that are being fixed up on a per model per PCB revision basis such as:
- enabling MMC UHS-I on board revisions that support it
- enabling PWM based on hwconfig
- fixing PCIe reset on GW552x
- removing cpu external watchdog reset on boards that do not support it
- populate PCI dt nodes based on PCI scan in order to fix GW16082
interrupt mapping and inject MAC address for PCI based GbE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:59 +0000 (13:10 -0800)]
imx: ventana: gw5904/gw5909: disable RS485
The GW5904/GW5909 have a SP33E multi-protocol serial transceiver which we
want to configure to RS232 by default (by de-asserting RS485_EN)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:58 +0000 (13:10 -0800)]
imx: ventana: add support for GW5901/GW5902
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:57 +0000 (13:10 -0800)]
imx: ventana: add support for GW5909
The GW5909 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW5904 but with half the DRAM loaded
and an additional RS232 transceiver off UART2.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:56 +0000 (13:10 -0800)]
imx: ventana: add support for GW5908
The GW5908 is a small single board computer based on the i.MX6DL SoC
with the same peripheral set as the GW530x but with 1GiB density DRAM
(64bit 512MiB).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:55 +0000 (13:10 -0800)]
imx: ventana: add support for GW5907
The GW5907 is a small single board computer based on the i.MX6DL SoC
with the following peripheral set:
- DDR3 memory (512MB default)
- 1x GigE (i.MX6 FEC)
- Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:54 +0000 (13:10 -0800)]
imx: ventana: add support for GW5906
The GW5906 is a GW552x with mechanical and power supply connector
differences.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:53 +0000 (13:10 -0800)]
imx: ventana: add i2c detect for all LVDS displays
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:52 +0000 (13:10 -0800)]
imx: ventana: skip nand init for nandless boards
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:51 +0000 (13:10 -0800)]
imx: ventana: add support for Z101WX01 LVDS display
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:50 +0000 (13:10 -0800)]
imx: ventana: add support for GW5905
The GW5905 is single-board tablet computer based on the i.MX6 SoC with the
following peripheral set:
- eMMC flash (boot device)
- microSD expansion
- LVDS display connector for off-board 3D+1C with PWM backlight
and I2C based touch controller
- MIPI camera connector supporting the TRULY CM8487-B500SA-E (OV5640)
- ublox EMMY-W1 WiFi/Bluetooth/NFC module (SDIO/UART)
- ublox ZOE-M8Q GPS
- LSM9DS1 9-DOF IMU
- 1x 1-lane miniPCIe socket with USB 2.0
- Gateworks System Controller
- Audio jack with TLV320AIC Audio Codec, Speaker AMP
and TSA227E Headphone detect
- MAX8607 3-mode LED camera flash
- DECT ULE module
- FUSB302 USB-C PD and ISL9238 Battery charger
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:49 +0000 (13:10 -0800)]
imx: ventana: remove setup of I2C3 from SPL
Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:48 +0000 (13:10 -0800)]
imx: ventana: do not iomux UART1
The only UART that is garunteed on Ventana boards is UART2 (serial-console).
Remove UART1 pinmux as that it is not consistent across all Ventana boards
and U-Boot doesn't need it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Mon, 4 Feb 2019 21:10:47 +0000 (13:10 -0800)]
imx: ventana: mv88e61xx change LED configuration
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:25 +0000 (16:40 +0000)]
configs: mx6sabresd: Reduce SPL size by disabling DOS, EXT and EFI support
With DM and FIT enabled in SPL, there is an sram overflow. By disabling
CONFIG_SPL_DOS_PARTITION, CONFIG_SPL_EXT_SUPPORT and
CONFIG_SPL_EFI_PARTITION, we get to keep the 'one binary to fit all'
for imx6[q|qp|dl] on sabresd since the final SPL image is now under 64KB.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:24 +0000 (16:40 +0000)]
board: mx6sabresd: Remove the enet reset gpio handling
Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi
and get rid of the enet reset gpio handling from the board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:23 +0000 (16:40 +0000)]
board: mx6sabresd: Remove non-DM code
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabresd board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:22 +0000 (16:40 +0000)]
configs: mx6sabresd: Add DM_SPI_FLASH necessary configs
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:22 +0000 (16:40 +0000)]
board: mx6sabreauto: Remove the non-DM code
Since the mx6sabreauto has DM support, remove the unused non-DM code
from mx6sabreauto board file.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:20 +0000 (16:40 +0000)]
configs: mx6sabreauto: Add DM_SPI_FLASH necessary configs
Enable all neceassary configs to support DM_SPI_FLASH on mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:19 +0000 (16:40 +0000)]
mx6sabreauto: Add DM_GPIO support
Add the DM_GPIO related config for mx6sabreauto.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:19 +0000 (16:40 +0000)]
mx6sabresd: Add DM_GPIO support
Add the DM_GPIO related config for mx6sabresd.
Also add the gpio request calls.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:18 +0000 (16:40 +0000)]
configs: mx6sabresd: Add SPL FIT and DM support
Enable all the necessary configs for SPL DM and FIT support for
mx6sabresd.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:17 +0000 (16:40 +0000)]
configs: mx6sabreauto: Add SPL FIT and DM support
Enable all the necessary configs for SPL DM and FIT support for
mx6sabreauto.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:16 +0000 (16:40 +0000)]
arm: dts: Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd]
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones
from kernel v4.20 (commit
8fe28cb58bcb2).
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:14 +0000 (16:40 +0000)]
arm: dts: Add all the imx6[q|qp|dl] sabre[auto|sd] u-boot dts[i] files
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:13 +0000 (16:40 +0000)]
board: mx6sabreauto: Add board_fit_config_name_match to support FIT in SPL
This matches one of the following three boards (or fails):
- imx6q-sabreauto
- imx6qp-sabreauto
- imx6dl-sabreauto
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:12 +0000 (16:40 +0000)]
board: mx6sabresd: Add board_fit_config_name_match to support FIT in SPL
This matches one of the following three boards (or fails):
- imx6q-sabresd
- imx6qp-sabresd
- imx6dl-sabresd
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:11 +0000 (16:40 +0000)]
mmc: fsl_esdhc: Fix DM_REGULATOR ifdefs for SPL builds
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:10 +0000 (16:40 +0000)]
configs: imx6sabreauto: Add DM_USB support
Add the DM support for USB. For that, DM_REGULATOR is needed.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:09 +0000 (16:40 +0000)]
configs: imx6sabreauto: Add DM_MMC support
Add DM_MMC config to imx6sabreauto defconfig.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Fri, 1 Feb 2019 16:40:08 +0000 (16:40 +0000)]
usb: ehci-mx6: Make regulator DM_REGULATOR dependent
Do the regulator related work only if the build has the DM_REGULATOR.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Abel Vesa [Fri, 1 Feb 2019 16:40:07 +0000 (16:40 +0000)]
usb: Rename SPL_USB_SUPPORT to SPL_USB_STORAGE
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Stefan Roese [Wed, 30 Jan 2019 07:54:12 +0000 (08:54 +0100)]
video: bmp: Add support for 24bpp BMP files on 16bpp displays
This patch adds support to load 24bpp BMP files on 16bpp displays. This
will be used by the theadorable board. The "old" bmp command did support
this operartion mode and to not break compatibility with the move to
DM_VIDEO, we need to add this support to the "new" bmp code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Priit Laes [Wed, 19 Dec 2018 13:06:09 +0000 (15:06 +0200)]
sunxi: display: Implement fallback to ddc probe when hpd fails
There are HDMI displays where hpd pin is not connected, thus
we cannot get it to work unless we specifically set the resolution.
Rework the display probing, so hotplug detect failure causes
fallback to probing ddc for EDID data.
Signed-off-by: Priit Laes <priit.laes@paf.com>
Priit Laes [Wed, 19 Dec 2018 13:06:08 +0000 (15:06 +0200)]
sunxi: display: Move DDC PLL setup to HDMI init
Move PLL initialization code to single place so
we won't call it every time we query for EDID data.
Signed-off-by: Priit Laes <priit.laes@paf.com>
Michal Simek [Thu, 14 Feb 2019 12:14:30 +0000 (13:14 +0100)]
arm64: zynqmp: Create fdtfile from compatible string
distro boot expects that fdtfile name is setup for alternative DTB.
Create this file based on the first platform compatible string.
This should ensure that one rootfs can store multiple DTBs for different
boards.
Reflect structure which is used in Linux kernel. It means dtbs are
strored in xilinx folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Venkatesh Yadav Abbarapu [Wed, 14 Nov 2018 11:50:18 +0000 (17:20 +0530)]
arm64: zynqmp: Change the spi-rx-bus-width property to x1
As per the zc1275 design x1 mode is enabled so changing the
spi-rx-bus-width property to x1.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Shubhrajyoti Datta [Mon, 3 Sep 2018 10:16:46 +0000 (15:46 +0530)]
arm64: zynqmp: Fix i2c boot warning
Fix the below warning as the core looks for the compatible
string.
[ 5.198919] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@19
[ 5.207454] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@19
[ 5.216394] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@30
[ 5.224986] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@30
[ 5.233927] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@35
[ 5.242527] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@35
[ 5.263880] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@36
[ 5.272477] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@36
[ 5.281415] i2c i2c-18: of_i2c: modalias failure on
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@51
[ 5.290008] i2c i2c-18: Failed to create I2C device for
/amba/i2c@
ff030000/i2c-mux@75/i2c@3/dev@51
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 13 Feb 2019 14:39:04 +0000 (15:39 +0100)]
arm64: zynqmp: Remove autodetected devices without description
It will never reach mainline that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Amit Kucheria [Thu, 23 Aug 2018 08:53:29 +0000 (14:23 +0530)]
arm64: dts: Fix various entry-method properties to reflect documentation
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit
a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 13 Feb 2019 15:39:51 +0000 (16:39 +0100)]
xilinx: dts: Remove additional empty lines
Trivial fix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mounika Grace Akula [Tue, 9 Oct 2018 15:22:50 +0000 (20:52 +0530)]
arm64: zynqmp: Add reset-on-timeout for all boards and modify default timeout value
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:20 +0000 (00:10 -0400)]
ARM: dts: zynq: correct and improve the model property of dt files
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luis Araneda [Thu, 12 Jul 2018 04:10:19 +0000 (00:10 -0400)]
ARM: dts: zynq: Set correct manufacturer for ZedBoard and MicroZed boards
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 26 Sep 2018 11:36:16 +0000 (13:36 +0200)]
ARM: dts: Use mmc@ instead sdhci@
mmc name is recommended based on devicetree specification.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tim Harvey [Mon, 4 Feb 2019 20:56:52 +0000 (12:56 -0800)]
net: mv88e61xx: fix autonegotiation on ports
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Breno Matheus Lima [Wed, 23 Jan 2019 19:30:16 +0000 (19:30 +0000)]
doc: imx: habv4: Remove secure_boot.txt guide
The secure_boot.txt guide was replaced by mx6_mx7_secure_boot.txt and
mx6_mx7_spl_secure_boot.txt documents.
Both documents covers all steps needed for SPL and non-SPL tagets,
so remove secure_boot.txt file to avoid duplicated content.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Jonathan Gray [Wed, 30 Jan 2019 22:24:44 +0000 (09:24 +1100)]
rpi: add Compute Module 3+
Add Raspberry Pi Compute Module 3+ to list of models, the revision code
is 0x10 according to the list on raspberrypi.org.
v2: Use the same dtb name as CM3 as CM3+ is a drop in replacement
for CM3.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Adam Heinrich [Mon, 31 Dec 2018 11:11:08 +0000 (12:11 +0100)]
cmd: bmp: Make integer-to-pointer cast platform, independent
This patch fixes the int-to-pointer-cast warning on aarch64.
Signed-off-by: Adam Heinrich <adam@adamh.cz>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:30:11 +0000 (19:30 +0000)]
doc: imx: habv4: Move encrypted boot guide
All guides are currently located at doc/imx/habv4/guides/ directory.
Move encrypted_boot.txt document to guides directory.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:30:06 +0000 (19:30 +0000)]
doc: imx: habv4: Add Secure Boot guide for i.MX6 and i.MX7 SPL targets
The current U-Boot implementation includes SPL targets for
some NXP development boards:
- mx6sabreauto_defconfig
- mx6sabresd_defconfig
- mx6ul_14x14_evk_defconfig
- mx6ul_9x9_evk_defconfig
Add additional steps needed to completly secure the
bootloader image.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:29:59 +0000 (19:29 +0000)]
doc: imx: habv4: Add Secure Boot guide for i.MX6 and i.MX7 non-SPL targets
Add HABv4 documentation for non-SPL targets covering the
following topics:
- How to sign an securely boot an u-boot-dtb.imx image.
- How to extend the root of trust for additional boot images.
- Add 3 CSF examples.
- Add IVT generation script example.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:29:53 +0000 (19:29 +0000)]
doc: imx: habv4: Add HABv4 introduction
The HABv4 is supported in i.MX50, i.MX53, i.MX6, i.MX7,
series and i.MX 8M, i.MX8MM devices.
Add an introductory document containing the following topics:
- HABv4 Introduction
- HABv4 Secure Boot
- HABv4 Encrypted Boot
- HAB PKI tree generation
- HAB Fast Authentication PKI tree generation
- SRK Table and SRK Hash generation
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Breno Matheus Lima [Wed, 23 Jan 2019 19:29:46 +0000 (19:29 +0000)]
doc: imx: habv4: Remove extra hab directory for a cleaner documentation structure
There is no need to have an extra hab directory under doc/imx/.
Habv4 and AHAB documentation can be added directly in doc/imx/ for a
cleaner documentation structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Marcin Niestroj [Sat, 19 Jan 2019 16:06:45 +0000 (17:06 +0100)]
ARM: dts: imx6ul-lite*: add DTS files for liteSOM and liteboard
Import liteSOM and liteboard dts files from Linux v4.20. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Adam Ford [Thu, 17 Jan 2019 13:16:39 +0000 (07:16 -0600)]
MTD: nand: mxs_nand: Allow driver to auto setup ECC in SPL
The initialization of the NAND in SPL hard-coded ecc.bytes,
ecc.size, and ecc.strength which may work for some NAND parts,
but it not appropriate for others. With the pending patch
"mxs_nand: Fix BCH read timeout error on boards requiring ECC"
the driver can auto configure the ECC when these entries are
blank. This patch has been tested in NAND flash with oob 64
and oob 128.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Adam Ford [Tue, 15 Jan 2019 17:26:48 +0000 (11:26 -0600)]
net: dm: fec: Fix regulator enable when using DM_REGULATOR
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes:
ad8c43cbcafb ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adam Ford [Sat, 12 Jan 2019 23:32:00 +0000 (17:32 -0600)]
ARM: imx6q_logic: Correct phy fixup for broken ethernet
The Ethernet has been broken for some time. This patch unifies
this board with a few others that use a similar approach to
enabling phy. This fixes ar8031 Ethernet controller so it works.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Sat, 12 Jan 2019 23:24:52 +0000 (17:24 -0600)]
ARM: imx6q_logic: Enable SPL Booting from NAND
This patch fixes a few values that were incorrect, and this
now lets SPL boot from NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>