review.tizen.org Git - platform/kernel/linux-rpi.git/log

igc: Lift TAPRIO schedule restriction

[ Upstream commit a5fd39464a4081ce11c801d7e20c4551ba7cb983 ]

Add support for Qbv schedules where one queue stays open
in consecutive entries. Currently that's not supported.

Example schedule:

|tc qdisc replace dev ${INTERFACE} handle 100 parent root taprio num_tc 3 \
|   map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
|   queues 1@0 1@1 2@2 \
|   base-time ${BASETIME} \
|   sched-entry S 0x01 300000 \ # Stream High/Low
|   sched-entry S 0x06 500000 \ # Management and Best Effort
|   sched-entry S 0x04 200000 \ # Best Effort
|   flags 0x02

Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 72abeedd8398 ("igc: Set Qbv start_time and end_time to end_time if not being configured in GCL")
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: recalculate Qbv end_time by considering cycle time

[ Upstream commit 6d05251d537a4d3835959a8cdd8cbbbdcdc0c904 ]

Qbv users can specify a cycle time that is not equal to the total GCL
intervals. Hence, recalculation is necessary here to exclude the time
interval that exceeds the cycle time. As those GCL which exceeds the
cycle time will be truncated.

According to IEEE Std. 802.1Q-2018 section 8.6.9.2, once the end of
the list is reached, it will switch to the END_OF_CYCLE state and
leave the gates in the same state until the next cycle is started.

Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading")
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: allow BaseTime 0 enrollment for Qbv

[ Upstream commit e17090eb24944fbbe1f24d9f336d7bad4fbe47e8 ]

Introduce qbv_enable flag in igc_adapter struct to store the Qbv on/off.
So this allow the BaseTime to enroll with zero value.

Fixes: 61572d5f8f91 ("igc: Simplify TSN flags handling")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: Add checking for basetime less than zero

[ Upstream commit 3b61764fb49a6e147ac90d71dccdddc9d5508ba1 ]

Using the tc qdisc command, the user can set basetime to any value.
Checking should be done on the driver's side to prevent registering
basetime values that are less than zero.

Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igc: Use strict cycles for Qbv scheduling

[ Upstream commit d8f45be01dd9381065a3778a579385249ed011dc ]

Configuring strict cycle mode in the controller forces more well
behaved transmissions when taprio is offloaded.

When set this strict_cycle and strict_end, transmission is not
enabled if the whole packet cannot be completed before end of
the Qbv cycle.

Fixes: 82faa9b79950 ("igc: Add support for ETF offloading")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

r6040: Fix kmemleak in probe and remove

[ Upstream commit 7e43039a49c2da45edc1d9d7c9ede4003ab45a5f ]

There is a memory leaks reported by kmemleak:

  unreferenced object 0xffff888116111000 (size 2048):
    comm "modprobe", pid 817, jiffies 4294759745 (age 76.502s)
    hex dump (first 32 bytes):
      00 c4 0a 04 81 88 ff ff 08 10 11 16 81 88 ff ff  ................
      08 10 11 16 81 88 ff ff 00 00 00 00 00 00 00 00  ................
    backtrace:
      [<ffffffff815bcd82>] kmalloc_trace+0x22/0x60
      [<ffffffff827e20ee>] phy_device_create+0x4e/0x90
      [<ffffffff827e6072>] get_phy_device+0xd2/0x220
      [<ffffffff827e7844>] mdiobus_scan+0xa4/0x2e0
      [<ffffffff827e8be2>] __mdiobus_register+0x482/0x8b0
      [<ffffffffa01f5d24>] r6040_init_one+0x714/0xd2c [r6040]
      ...

The problem occurs in probe process as follows:
  r6040_init_one:
    mdiobus_register
      mdiobus_scan    <- alloc and register phy_device,
                         the reference count of phy_device is 3
    r6040_mii_probe
      phy_connect     <- connect to the first phy_device,
                         so the reference count of the first
                         phy_device is 4, others are 3
    register_netdev   <- fault inject succeeded, goto error handling path

    // error handling path
    err_out_mdio_unregister:
      mdiobus_unregister(lp->mii_bus);
    err_out_mdio:
      mdiobus_free(lp->mii_bus);    <- the reference count of the first
                                       phy_device is 1, it is not released
                                       and other phy_devices are released
  // similarly, the remove process also has the same problem

The root cause is traced to the phy_device is not disconnected when
removes one r6040 device in r6040_remove_one() or on error handling path
after r6040_mii probed successfully. In r6040_mii_probe(), a net ethernet
device is connected to the first PHY device of mii_bus, in order to
notify the connected driver when the link status changes, which is the
default behavior of the PHY infrastructure to handle everything.
Therefore the phy_device should be disconnected when removes one r6040
device or on error handling path.

Fix it by adding phy_disconnect() when removes one r6040 device or on
error handling path after r6040_mii probed successfully.

Fixes: 3831861b4ad8 ("r6040: implement phylib")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221213125614.927754-1-lizetao1@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

unix: Fix race in SOCK_SEQPACKET's unix_dgram_sendmsg()

[ Upstream commit 3ff8bff704f4de125dca2262e5b5b963a3da1d87 ]

There is a race resulting in alive SOCK_SEQPACKET socket
may change its state from TCP_ESTABLISHED to TCP_CLOSE:

unix_release_sock(peer)                  unix_dgram_sendmsg(sk)
  sock_orphan(peer)
    sock_set_flag(peer, SOCK_DEAD)
                                           sock_alloc_send_pskb()
                                             if !(sk->sk_shutdown & SEND_SHUTDOWN)
                                               OK
                                           if sock_flag(peer, SOCK_DEAD)
                                             sk->sk_state = TCP_CLOSE
  sk->sk_shutdown = SHUTDOWN_MASK

After that socket sk remains almost normal: it is able to connect, listen, accept
and recvmsg, while it can't sendmsg.

Since this is the only possibility for alive SOCK_SEQPACKET to change
the state in such way, we should better fix this strange and potentially
danger corner case.

Note, that we will return EPIPE here like this is normally done in sock_alloc_send_pskb().
Originally used ECONNREFUSED looks strange, since it's strange to return
a specific retval in dependence of race in kernel, when user can't affect on this.

Also, move TCP_CLOSE assignment for SOCK_DGRAM sockets under state lock
to fix race with unix_dgram_connect():

unix_dgram_connect(other)            unix_dgram_sendmsg(sk)
                                       unix_peer(sk) = NULL
                                       unix_state_unlock(sk)
  unix_state_double_lock(sk, other)
  sk->sk_state  = TCP_ESTABLISHED
  unix_peer(sk) = other
  unix_state_double_unlock(sk, other)
                                       sk->sk_state  = TCP_CLOSED

This patch fixes both of these races.

Fixes: 83301b5367a9 ("af_unix: Set TCP_ESTABLISHED for datagram sockets too")
Signed-off-by: Kirill Tkhai <tkhai@ya.ru>
Link: https://lore.kernel.org/r/135fda25-22d5-837a-782b-ceee50e19844@ya.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfc: pn533: Clear nfc_target before being used

[ Upstream commit 9f28157778ede0d4f183f7ab3b46995bb400abbe ]

Fix a slab-out-of-bounds read that occurs in nla_put() called from
nfc_genl_send_target() when target->sensb_res_len, which is duplicated
from an nfc_target in pn533, is too large as the nfc_target is not
properly initialized and retains garbage values. Clear nfc_targets with
memset() before they are used.

Found by a modified version of syzkaller.

BUG: KASAN: slab-out-of-bounds in nla_put
Call Trace:
memcpy
nla_put
nfc_genl_dump_targets
genl_lock_dumpit
netlink_dump
__netlink_dump_start
genl_family_rcv_msg_dumpit
genl_rcv_msg
netlink_rcv_skb
genl_rcv
netlink_unicast
netlink_sendmsg
sock_sendmsg
____sys_sendmsg
___sys_sendmsg
__sys_sendmsg
do_syscall_64

Fixes: 673088fb42d0 ("NFC: pn533: Send ATR_REQ directly for active device detection")
Fixes: 361f3cb7f9cf ("NFC: DEP link hook implementation for pn533")
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221214015139.119673-1-linuxlovemin@yonsei.ac.kr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: enetc: avoid buffer leaks on xdp_do_redirect() failure

[ Upstream commit 628050ec952d2e2e46ec9fb6aa07e41139e030c8 ]

Before enetc_clean_rx_ring_xdp() calls xdp_do_redirect(), each software
BD in the RX ring between index orig_i and i can have one of 2 refcount
values on its page.

We are the owner of the current buffer that is being processed, so the
refcount will be at least 1.

If the current owner of the buffer at the diametrically opposed index
in the RX ring (i.o.w, the other half of this page) has not yet called
kfree(), this page's refcount could even be 2.

enetc_page_reusable() in enetc_flip_rx_buff() tests for the page
refcount against 1, and [ if it's 2 ] does not attempt to reuse it.

But if enetc_flip_rx_buff() is put after the xdp_do_redirect() call,
the page refcount can have one of 3 values. It can also be 0, if there
is no owner of the other page half, and xdp_do_redirect() for this
buffer ran so far that it triggered a flush of the devmap/cpumap bulk
queue, and the consumers of those bulk queues also freed the buffer,
all by the time xdp_do_redirect() returns the execution back to enetc.

This is the reason why enetc_flip_rx_buff() is called before
xdp_do_redirect(), but there is a big flaw with that reasoning:
enetc_flip_rx_buff() will set rx_swbd->page = NULL on both sides of the
enetc_page_reusable() branch, and if xdp_do_redirect() returns an error,
we call enetc_xdp_free(), which does not deal gracefully with that.

In fact, what happens is quite special. The page refcounts start as 1.
enetc_flip_rx_buff() figures they're reusable, transfers these
rx_swbd->page pointers to a different rx_swbd in enetc_reuse_page(), and
bumps the refcount to 2. When xdp_do_redirect() later returns an error,
we call the no-op enetc_xdp_free(), but we still haven't lost the
reference to that page. A copy of it is still at rx_ring->next_to_alloc,
but that has refcount 2 (and there are no concurrent owners of it in
flight, to drop the refcount). What really kills the system is when
we'll flip the rx_swbd->page the second time around. With an updated
refcount of 2, the page will not be reusable and we'll really leak it.
Then enetc_new_page() will have to allocate more pages, which will then
eventually leak again on further errors from xdp_do_redirect().

The problem, summarized, is that we zeroize rx_swbd->page before we're
completely done with it, and this makes it impossible for the error path
to do something with it.

Since the packet is potentially multi-buffer and therefore the
rx_swbd->page is potentially an array, manual passing of the old
pointers between enetc_flip_rx_buff() and enetc_xdp_free() is a bit
difficult.

For the sake of going with a simple solution, we accept the possibility
of racing with xdp_do_redirect(), and we move the flip procedure to
execute only on the redirect success path. By racing, I mean that the
page may be deemed as not reusable by enetc (having a refcount of 0),
but there will be no leak in that case, either.

Once we accept that, we have something better to do with buffers on
XDP_REDIRECT failure. Since we haven't performed half-page flipping yet,
we won't, either (and this way, we can avoid enetc_xdp_free()
completely, which gives the entire page to the slab allocator).
Instead, we'll call enetc_xdp_drop(), which will recycle this half of
the buffer back to the RX ring.

Fixes: 9d2b68cc108d ("net: enetc: add support for XDP_REDIRECT")
Suggested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221213001908.2347046-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/bpf: Add test for unstable CT lookup API

[ Upstream commit 87091063df5d4845d1db0761a9ed5510c4756a96 ]

This tests that we return errors as documented, and also that the kfunc
calls work from both XDP and TC hooks.

Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220114163953.1455836-8-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: a8dfde09c901 ("selftests/bpf: Select CONFIG_FUNCTION_ERROR_INJECTION")
Signed-off-by: Sasha Levin <sashal@kernel.org>

block, bfq: fix possible uaf for 'bfqq->bic'

[ Upstream commit 64dc8c732f5c2b406cc752e6aaa1bd5471159cab ]

Our test report a uaf for 'bfqq->bic' in 5.10:

==================================================================
BUG: KASAN: use-after-free in bfq_select_queue+0x378/0xa30

CPU: 6 PID: 2318352 Comm: fsstress Kdump: loaded Not tainted 5.10.0-60.18.0.50.h602.kasan.eulerosv2r11.x86_64 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58-20220320_160524-szxrtosci10000 04/01/2014
Call Trace:
bfq_select_queue+0x378/0xa30
bfq_dispatch_request+0xe8/0x130
blk_mq_do_dispatch_sched+0x62/0xb0
__blk_mq_sched_dispatch_requests+0x215/0x2a0
blk_mq_sched_dispatch_requests+0x8f/0xd0
__blk_mq_run_hw_queue+0x98/0x180
__blk_mq_delay_run_hw_queue+0x22b/0x240
blk_mq_run_hw_queue+0xe3/0x190
blk_mq_sched_insert_requests+0x107/0x200
blk_mq_flush_plug_list+0x26e/0x3c0
blk_finish_plug+0x63/0x90
__iomap_dio_rw+0x7b5/0x910
iomap_dio_rw+0x36/0x80
ext4_dio_read_iter+0x146/0x190 [ext4]
ext4_file_read_iter+0x1e2/0x230 [ext4]
new_sync_read+0x29f/0x400
vfs_read+0x24e/0x2d0
ksys_read+0xd5/0x1b0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6

Commit 3bc5e683c67d ("bfq: Split shared queues on move between cgroups")
changes that move process to a new cgroup will allocate a new bfqq to
use, however, the old bfqq and new bfqq can point to the same bic:

1) Initial state, two process with io in the same cgroup.

Process 1       Process 2
(BIC1)          (BIC2)
  |  Λ            |  Λ
  |  |            |  |
  V  |            V  |
  bfqq1           bfqq2

2) bfqq1 is merged to bfqq2.

Process 1       Process 2
(BIC1)          (BIC2)
  |               |
   \-------------\|
                  V
  bfqq1           bfqq2(coop)

3) Process 1 exit, then issue new io(denoce IOA) from Process 2.

(BIC2)
  |  Λ
  |  |
  V  |
  bfqq2(coop)

4) Before IOA is completed, move Process 2 to another cgroup and issue io.

Process 2
(BIC2)
   Λ
   |\--------------\
   |                V
  bfqq2           bfqq3

Now that BIC2 points to bfqq3, while bfqq2 and bfqq3 both point to BIC2.
If all the requests are completed, and Process 2 exit, BIC2 will be
freed while there is no guarantee that bfqq2 will be freed before BIC2.

Fix the problem by clearing bfqq->bic while bfqq is detached from bic.

Fixes: 3bc5e683c67d ("bfq: Split shared queues on move between cgroups")
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221214030430.3304151-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mISDN: hfcmulti: don't call dev_kfree_skb/kfree_skb() under spin_lock_irqsave()

[ Upstream commit 1232946cf522b8de9e398828bde325d7c41f29dd ]

It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.

skb_queue_purge() is called under spin_lock_irqsave() in handle_dmsg()
and hfcm_l1callback(), kfree_skb() is called in them, to fix this, use
skb_queue_splice_init() to move the dch->squeue to a free queue, also
enqueue the tx_skb and rx_skb, at last calling __skb_queue_purge() to
free the SKBs afer unlock.

Fixes: af69fb3a8ffa ("Add mISDN HFC multiport driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mISDN: hfcpci: don't call dev_kfree_skb/kfree_skb() under spin_lock_irqsave()

[ Upstream commit f0f596bd75a9d573ca9b587abb39cee0b916bb82 ]

It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.

skb_queue_purge() is called under spin_lock_irqsave() in hfcpci_l2l1D(),
kfree_skb() is called in it, to fix this, use skb_queue_splice_init()
to move the dch->squeue to a free queue, also enqueue the tx_skb and
rx_skb, at last calling __skb_queue_purge() to free the SKBs afer unlock.

Fixes: 1700fe1a10dc ("Add mISDN HFC PCI driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mISDN: hfcsusb: don't call dev_kfree_skb/kfree_skb() under spin_lock_irqsave()

[ Upstream commit ddc9648db162eee556edd5222d2808fe33730203 ]

It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.

It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.

skb_queue_purge() is called under spin_lock_irqsave() in hfcusb_l2l1D(),
kfree_skb() is called in it, to fix this, use skb_queue_splice_init()
to move the dch->squeue to a free queue, also enqueue the tx_skb and
rx_skb, at last calling __skb_queue_purge() to free the SKBs afer unlock.

In tx_iso_complete(), dev_kfree_skb() is called to consume the transmitted
SKB, so replace it with dev_consume_skb_irq().

Fixes: 69f52adb2d53 ("mISDN: Add HFC USB driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: macsec: fix net device access prior to holding a lock

[ Upstream commit f3b4a00f0f62da252c598310698dfc82ef2f2e2e ]

Currently macsec offload selection update routine accesses
the net device prior to holding the relevant lock.
Fix by holding the lock prior to the device access.

Fixes: dcb780fb2795 ("net: macsec: add nla support for changing the offloading selection")
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Link: https://lore.kernel.org/r/20221211075532.28099-1-ehakim@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfsd: under NFSv4.1, fix double svc_xprt_put on rpc_create failure

[ Upstream commit 3bc8edc98bd43540dbe648e4ef91f443d6d20a24 ]

On error situation `clp->cl_cb_conn.cb_xprt` should not be given
a reference to the xprt otherwise both client cleanup and the
error handling path of the caller call to put it. Better to
delay handing over the reference to a later branch.

[   72.530665] refcount_t: underflow; use-after-free.
[   72.531933] WARNING: CPU: 0 PID: 173 at lib/refcount.c:28 refcount_warn_saturate+0xcf/0x120
[   72.533075] Modules linked in: nfsd(OE) nfsv4(OE) nfsv3(OE) nfs(OE) lockd(OE) compat_nfs_ssc(OE) nfs_acl(OE) rpcsec_gss_krb5(OE) auth_rpcgss(OE) rpcrdma(OE) dns_resolver fscache netfs grace rdma_cm iw_cm ib_cm sunrpc(OE) mlx5_ib mlx5_core mlxfw pci_hyperv_intf ib_uverbs ib_core xt_MASQUERADE nf_conntrack_netlink nft_counter xt_addrtype nft_compat br_netfilter bridge stp llc nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set overlay nf_tables nfnetlink crct10dif_pclmul crc32_pclmul ghash_clmulni_intel xfs serio_raw virtio_net virtio_blk net_failover failover fuse [last unloaded: sunrpc]
[   72.540389] CPU: 0 PID: 173 Comm: kworker/u16:5 Tainted: G           OE     5.15.82-dan #1
[   72.541511] Hardware name: Red Hat KVM/RHEL-AV, BIOS 1.16.0-3.module+el8.7.0+1084+97b81f61 04/01/2014
[   72.542717] Workqueue: nfsd4_callbacks nfsd4_run_cb_work [nfsd]
[   72.543575] RIP: 0010:refcount_warn_saturate+0xcf/0x120
[   72.544299] Code: 55 00 0f 0b 5d e9 01 50 98 00 80 3d 75 9e 39 08 00 0f 85 74 ff ff ff 48 c7 c7 e8 d1 60 8e c6 05 61 9e 39 08 01 e8 f6 51 55 00 <0f> 0b 5d e9 d9 4f 98 00 80 3d 4b 9e 39 08 00 0f 85 4c ff ff ff 48
[   72.546666] RSP: 0018:ffffb3f841157cf0 EFLAGS: 00010286
[   72.547393] RAX: 0000000000000026 RBX: ffff89ac6231d478 RCX: 0000000000000000
[   72.548324] RDX: ffff89adb7c2c2c0 RSI: ffff89adb7c205c0 RDI: ffff89adb7c205c0
[   72.549271] RBP: ffffb3f841157cf0 R08: 0000000000000000 R09: c0000000ffefffff
[   72.550209] R10: 0000000000000001 R11: ffffb3f841157ad0 R12: ffff89ac6231d180
[   72.551142] R13: ffff89ac6231d478 R14: ffff89ac40c06180 R15: ffff89ac6231d4b0
[   72.552089] FS:  0000000000000000(0000) GS:ffff89adb7c00000(0000) knlGS:0000000000000000
[   72.553175] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   72.553934] CR2: 0000563a310506a8 CR3: 0000000109a66000 CR4: 0000000000350ef0
[   72.554874] Call Trace:
[   72.555278]  <TASK>
[   72.555614]  svc_xprt_put+0xaf/0xe0 [sunrpc]
[   72.556276]  nfsd4_process_cb_update.isra.11+0xb7/0x410 [nfsd]
[   72.557087]  ? update_load_avg+0x82/0x610
[   72.557652]  ? cpuacct_charge+0x60/0x70
[   72.558212]  ? dequeue_entity+0xdb/0x3e0
[   72.558765]  ? queued_spin_unlock+0x9/0x20
[   72.559358]  nfsd4_run_cb_work+0xfc/0x270 [nfsd]
[   72.560031]  process_one_work+0x1df/0x390
[   72.560600]  worker_thread+0x37/0x3b0
[   72.561644]  ? process_one_work+0x390/0x390
[   72.562247]  kthread+0x12f/0x150
[   72.562710]  ? set_kthread_struct+0x50/0x50
[   72.563309]  ret_from_fork+0x22/0x30
[   72.563818]  </TASK>
[   72.564189] ---[ end trace 031117b1c72ec616 ]---
[   72.566019] list_add corruption. next->prev should be prev (ffff89ac4977e538), but was ffff89ac4763e018. (next=ffff89ac4763e018).
[   72.567647] ------------[ cut here ]------------

Fixes: a4abc6b12eb1 ("nfsd: Fix svc_xprt refcnt leak when setup callback client failed")
Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: pcf85063: fix pcf85063_clkout_control

[ Upstream commit c2d12e85336f6d4172fb2bab5935027c446d7343 ]

pcf85063_clkout_control reads the wrong register but then update the
correct one.

Reported-by: Janne Terho <janne.terho@ouman.fi>
Fixes: 8c229ab6048b ("rtc: pcf85063: Add pcf85063 clkout control to common clock framework")
Link: https://lore.kernel.org/r/20221211223553.59955-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: pic32: Move devm_rtc_allocate_device earlier in pic32_rtc_probe()

[ Upstream commit 90cd5c88830140c9fade92a8027e0fb2c6e4cc49 ]

The pic32_rtc_enable(pdata, 0) and clk_disable_unprepare(pdata->clk)
should be called in the error handling of devm_rtc_allocate_device(),
so we should move devm_rtc_allocate_device earlier in pic32_rtc_probe()
to fix it.

Fixes: 6515e23b9fde ("rtc: pic32: convert to devm_rtc_allocate_device")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221123015953.1998521-1-cuigaosheng1@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: st-lpc: Add missing clk_disable_unprepare in st_rtc_probe()

[ Upstream commit 5fb733d7bd6949e90028efdce8bd528c6ab7cf1e ]

The clk_disable_unprepare() should be called in the error handling
of clk_get_rate(), fix it.

Fixes: b5b2bdfc2893 ("rtc: st: Add new driver for ST's LPC RTC")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221123014805.1993052-1-cuigaosheng1@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: flowtable: really fix NAT IPv6 offload

[ Upstream commit 5fb45f95eec682621748b7cb012c6a8f0f981e6a ]

The for-loop was broken from the start. It translates to:

for (i = 0; i < 4; i += 4)

which means the loop statement is run only once, so only the highest
32-bit of the IPv6 address gets mangled.

Fix the loop increment.

Fixes: 0e07e25b481a ("netfilter: flowtable: fix NAT IPv6 offload mangling")
Fixes: 5c27d8d76ce8 ("netfilter: nf_flow_table_offload: add IPv6 support")
Signed-off-by: Qingfang DENG <dqfext@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: pm8008: Fix return value check in pm8008_probe()

[ Upstream commit 14f8c55d48e02157519fbcb3a5de557abd8a06e2 ]

In case of error, the function devm_regmap_init_i2c() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().

Fixes: 6b149f3310a4 ("mfd: pm8008: Add driver for QCOM PM8008 PMIC")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221125073626.1868229-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: pm8008: Remove driver data structure pm8008_data

[ Upstream commit 915696927cd6e7838d25dab8fbd2ae05d4acce84 ]

Maintaining a local driver data structure that is never shared
outside of the core device is an unnecessary complexity. Half of the
attributes were not used outside of a single function, one of which
was not used at all. The remaining 2 are generic and can be passed
around as required.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stable-dep-of: 14f8c55d48e0 ("mfd: pm8008: Fix return value check in pm8008_probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: qcom_rpm: Fix an error handling path in qcom_rpm_probe()

[ Upstream commit 36579aca877a62f67ecd77eb3edefc4c86292406 ]

If an error occurs after the clk_prepare_enable() call, a corresponding
clk_disable_unprepare() should be called.

Simplify code and switch to devm_clk_get_enabled() to fix it.

Fixes: 3526403353c2 ("mfd: qcom_rpm: Handle message RAM clock")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/e39752476d02605b2be46cab7115f71255ce13a8.1668949256.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: bd957x: Fix Kconfig dependency on REGMAP_IRQ

[ Upstream commit 85842c46fd47fa6bd78681c154223bed27d5fd19 ]

The BD957x driver uses REGMAP_IRQ but does not 'select' to depend on
it. This can cause build failures. Select REGMAP_IRQ for BD957X.

Fixes: 0e9692607f94 ("mfd: bd9576: Add IRQ support")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/Y3SdCWkRr1L64SWK@dc75zzyyyyyyyyyyyyydt-3.rev.dnainternet.fi
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pseries/eeh: use correct API for error log size

[ Upstream commit 9aafbfa5f57a4b75bafd3bed0191e8429c5fa618 ]

rtas-error-log-max is not the name of an RTAS function, so rtas_token()
is not the appropriate API for retrieving its value. We already have
rtas_get_error_log_max() which returns a sensible value if the property
is absent for any reason, so use that instead.

Fixes: 8d633291b4fc ("powerpc/eeh: pseries platform EEH error log retrieval")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
[mpe: Drop no-longer possible error handling as noticed by ajd]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221118150751.469393-6-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/eeh: Drop redundant spinlock initialization

[ Upstream commit 3def164a5cedad9117859dd4610cae2cc59cb6d2 ]

slot_errbuf_lock has declared and initialized by DEFINE_SPINLOCK,
so we don't need to spin_lock_init again, drop it.

Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1652232476-9696-1-git-send-email-baihaowen@meizu.com
Stable-dep-of: 9aafbfa5f57a ("powerpc/pseries/eeh: use correct API for error log size")
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: qcom: q6v5: Fix missing clk_disable_unprepare() in q6v5_wcss_qcs404_power_on()

[ Upstream commit 7ff5d60f18bba5cbaf17b2926aa9da44d5beca01 ]

q6v5_wcss_qcs404_power_on() have no fail path for readl_poll_timeout().
Add fail path for readl_poll_timeout().

Fixes: 0af65b9b915e ("remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204082757.18850-1-shangxiaojing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: qcom_q6v5_pas: Fix missing of_node_put() in adsp_alloc_memory_region()

[ Upstream commit 38e7d9c19276832ebb0277f415b9214bf7baeb37 ]

The pointer node is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.

Fixes: b9e718e950c3 ("remoteproc: Introduce Qualcomm ADSP PIL")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221203070639.15128-1-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: qcom_q6v5_pas: detach power domains on remove

[ Upstream commit 34d01df00b84127be04c914fc9f8e8be1fcdf851 ]

We need to detach from the power domains also on remove, not just on
probe fail so a subsequent probe works as expected.

Otherwise the following error appears on re-probe:

[   29.452005] sysfs: cannot create duplicate filename '/devices/genpd:0:3000000.remoteproc'
[   29.477121] CPU: 1 PID: 483 Comm: sh Tainted: G        W          6.1.0-rc4-00075-g71a113770bda #78
[   29.510319] Hardware name: Fairphone 4 (DT)
[   29.538335] Call trace:
[   29.564470]  dump_backtrace.part.0+0xe0/0xf0
[   29.592602]  show_stack+0x18/0x30
[   29.619616]  dump_stack_lvl+0x64/0x80
[   29.646834]  dump_stack+0x18/0x34
[   29.673541]  sysfs_warn_dup+0x60/0x7c
[   29.700592]  sysfs_create_dir_ns+0xec/0x110
[   29.728057]  kobject_add_internal+0xb8/0x374
[   29.755530]  kobject_add+0x9c/0x104
[   29.782072]  device_add+0xbc/0x8a0
[   29.808445]  device_register+0x20/0x30
[   29.835175]  genpd_dev_pm_attach_by_id+0xa4/0x190
[   29.862851]  genpd_dev_pm_attach_by_name+0x3c/0xb0
[   29.890472]  dev_pm_domain_attach_by_name+0x20/0x30
[   29.918212]  adsp_probe+0x278/0x580
[   29.944384]  platform_probe+0x68/0xc0
[   29.970603]  really_probe+0xbc/0x2dc
[   29.996662]  __driver_probe_device+0x78/0xe0
[   30.023491]  device_driver_attach+0x48/0xac
[   30.050215]  bind_store+0xb8/0x114
[   30.075957]  drv_attr_store+0x24/0x3c
[   30.101874]  sysfs_kf_write+0x44/0x54
[   30.127751]  kernfs_fop_write_iter+0x120/0x1f0
[   30.154448]  vfs_write+0x1ac/0x380
[   30.179937]  ksys_write+0x70/0x104
[   30.205274]  __arm64_sys_write+0x1c/0x2c
[   30.231060]  invoke_syscall+0x48/0x114
[   30.256594]  el0_svc_common.constprop.0+0x44/0xec
[   30.283183]  do_el0_svc+0x2c/0xd0
[   30.308320]  el0_svc+0x2c/0x84
[   30.333059]  el0t_64_sync_handler+0xf4/0x120
[   30.359001]  el0t_64_sync+0x18c/0x190
[   30.384385] kobject_add_internal failed for genpd:0:3000000.remoteproc with -EEXIST, don't try to register things with the same name in the same directory.
[   30.406029] remoteproc remoteproc0: releasing 3000000.remoteproc
[   30.416064] qcom_q6v5_pas: probe of 3000000.remoteproc failed with error -17

Fixes: 17ee2fb4e856 ("remoteproc: qcom: pas: Vote for active/proxy power domains")
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221118090816.100012-2-luca.weiss@fairphone.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: qcom_q6v5_pas: disable wakeup on probe fail or remove

[ Upstream commit 9a70551996e699fda262e8d54bbd41739d7aad6d ]

Leaving wakeup enabled during probe fail (-EPROBE_DEFER) or remove makes
the subsequent probe fail.

[    3.749454] remoteproc remoteproc0: releasing 3000000.remoteproc
[    3.752949] qcom_q6v5_pas: probe of 3000000.remoteproc failed with error -17
[    3.878935] remoteproc remoteproc0: releasing 4080000.remoteproc
[    3.887602] qcom_q6v5_pas: probe of 4080000.remoteproc failed with error -17
[    4.319552] remoteproc remoteproc0: releasing 8300000.remoteproc
[    4.332716] qcom_q6v5_pas: probe of 8300000.remoteproc failed with error -17

Fix this by disabling wakeup in both cases so the driver can properly
probe on the next try.

Fixes: a781e5aa5911 ("remoteproc: core: Prevent system suspend during remoteproc recovery")
Fixes: dc86c129b4fb ("remoteproc: qcom: pas: Mark devices as wakeup capable")
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221118090816.100012-1-luca.weiss@fairphone.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: qcom: q6v5: Fix potential null-ptr-deref in q6v5_wcss_init_mmio()

[ Upstream commit f360e2b275efbb745ba0af8b47d9ef44221be586 ]

q6v5_wcss_init_mmio() will call platform_get_resource_byname() that may
fail and return NULL. devm_ioremap() will use res->start as input, which
may causes null-ptr-deref. Check the ret value of
platform_get_resource_byname() to avoid the null-ptr-deref.

Fixes: 0af65b9b915e ("remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221125021641.29392-1-shangxiaojing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: sysmon: fix memory leak in qcom_add_sysmon_subdev()

[ Upstream commit e01ce676aaef3b13d02343d7e70f9637d93a3367 ]

The kfree() should be called when of_irq_get_byname() fails or
devm_request_threaded_irq() fails in qcom_add_sysmon_subdev(),
otherwise there will be a memory leak, so add kfree() to fix it.

Fixes: 027045a6e2b7 ("remoteproc: qcom: Add shutdown-ack irq")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221129105650.1539187-1-cuigaosheng1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: mediatek: always use bus clock for PWM on MT7622

[ Upstream commit aa3c668f2f98856af96e13f44da6ca4f26f0b98c ]

According to MT7622 Reference Manual for Development Board v1.0 the PWM
unit found in the MT7622 SoC also comes with the PWM_CK_26M_SEL register
at offset 0x210 just like other modern MediaTek ARM64 SoCs.
And also MT7622 sets that register to 0x00000001 on reset which is
described as 'Select 26M fix CLK as BCLK' in the datasheet.
Hence set has_ck_26m_sel to true also for MT7622 which results in the
driver writing 0 to the PWM_CK_26M_SEL register which is described as
'Select bus CLK as BCLK'.

Fixes: 0c0ead76235db0 ("pwm: mediatek: Always use bus clock")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/Y1iF2slvSblf6bYK@makrotopia.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: mtk-disp: Fix the parameters calculated by the enabled flag of disp_pwm

[ Upstream commit 0b5ef3429d8f78427558ab0dcbfd862098ba2a63 ]

In the original mtk_disp_pwm_get_state() function wrongly uses bit 0 of
CON0 to judge if the PWM is enabled.
However that is indicated by a bit (at a machine dependent position) in
the DISP_PWM_EN register. Fix this accordingly.

Fixes: 3f2b16734914 ("pwm: mtk-disp: Implement atomic API .get_state()")
Signed-off-by: xinlei lee <xinlei.lee@mediatek.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/1666172538-11652-1-git-send-email-xinlei.lee@mediatek.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: sifive: Call pwm_sifive_update_clock() while mutex is held

[ Upstream commit 45558b3abb87eeb2cedb8a59cb2699c120b5102a ]

As was documented in commit 0f02f491b786 ("pwm: sifive: Reduce time the
controller lock is held") a caller of pwm_sifive_update_clock() must
hold the mutex. So fix pwm_sifive_clock_notifier() to grab the lock.

While this necessity was only documented later, the race exists since
the driver was introduced.

Fixes: 9e37a53eb051 ("pwm: sifive: Add a driver for SiFive SoC PWM")
Reported-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Link: https://lore.kernel.org/r/20221018061656.1428111-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/sun50i: Remove IOMMU_DOMAIN_IDENTITY

[ Upstream commit ef5bb8e7a7127218f826b9ccdf7508e7a339f4c2 ]

This driver treats IOMMU_DOMAIN_IDENTITY the same as UNMANAGED, which
cannot possibly be correct.

UNMANAGED domains are required to start out blocking all DMAs. This seems
to be what this driver does as it allocates a first level 'dt' for the IO
page table that is 0 filled.

Thus UNMANAGED looks like a working IO page table, and so IDENTITY must be
a mistake. Remove it.

Fixes: 4100b8c229b3 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0-v1-97f0adf27b5e+1f0-s50_identity_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/powerpc: Fix resource leaks

[ Upstream commit 8f4ab7da904ab7027ccd43ddb4f0094e932a5877 ]

In check_all_cpu_dscr_defaults, opendir() opens the directory stream.
Add missing closedir() in the error path to release it.

In check_cpu_dscr_default, open() creates an open file descriptor.
Add missing close() in the error path to release it.

Fixes: ebd5858c904b ("selftests/powerpc: Add test for all DSCR sysfs interfaces")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221205084429.570654-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/hv-gpci: Fix hv_gpci event list

[ Upstream commit 03f7c1d2a49acd30e38789cd809d3300721e9b0e ]

Based on getPerfCountInfo v1.018 documentation, some of the
hv_gpci events were deprecated for platform firmware that
supports counter_info_version 0x8 or above.

Fix the hv_gpci event list by adding a new attribute group
called "hv_gpci_event_attrs_v6" and a "ENABLE_EVENTS_COUNTERINFO_V6"
macro to enable these events for platform firmware
that supports counter_info_version 0x6 or below. And assigning
the hv_gpci event list based on output counter info version
of underlying plaform.

Fixes: 97bf2640184f ("powerpc/perf/hv-gpci: add the remaining gpci requests")
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221130174513.87501-1-kjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/83xx/mpc832x_rdb: call platform_device_put() in error case in of_fsl_spi_probe()

[ Upstream commit 4d0eea415216fe3791da2f65eb41399e70c7bedf ]

If platform_device_add() is not called or failed, it can not call
platform_device_del() to clean up memory, it should call
platform_device_put() in error case.

Fixes: 26f6cb999366 ("[POWERPC] fsl_soc: add support for fsl_spi")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221029111626.429971-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/perf: callchain validate kernel stack pointer bounds

[ Upstream commit 32c5209214bd8d4f8c4e9d9b630ef4c671f58e79 ]

The interrupt frame detection and loads from the hypothetical pt_regs
are not bounds-checked. The next-frame validation only bounds-checks
STACK_FRAME_OVERHEAD, which does not include the pt_regs. Add another
test for this.

The user could set r1 to be equal to the address matching the first
interrupt frame - STACK_INT_FRAME_SIZE, which is in the previous page
due to the kernel redzone, and induce the kernel to load the marker from
there. Possibly this could cause a crash at least. If the user could
induce the previous page to contain a valid marker, then it might be
able to direct perf to read specific memory addresses in a way that
could be transmitted back to the user in the perf data.

Fixes: 20002ded4d93 ("perf_counter: powerpc: Add callchain support")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221127124942.1665522-4-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/xive: add missing iounmap() in error path in xive_spapr_populate_irq_data()

[ Upstream commit 8b49670f3bb3f10cd4d5a6dca17f5a31b173ecdc ]

If remapping 'data->trig_page' fails, the 'data->eoi_mmio' need be unmapped
before returning from xive_spapr_populate_irq_data().

Fixes: eac1e731b59e ("powerpc/xive: guest exploitation of the XIVE interrupt controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221017032333.1852406-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/xmon: Fix -Wswitch-unreachable warning in bpt_cmds

[ Upstream commit 1c4a4a4c8410be4a231a58b23e7a30923ff954ac ]

When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable into the case that uses it, which silences the warning:

arch/powerpc/xmon/xmon.c: In function ‘bpt_cmds’:
arch/powerpc/xmon/xmon.c:1529:13: warning: statement will never be executed [-Wswitch-unreachable]
1529 | int mode;
| ^~~~

Fixes: 09b6c1129f89 ("powerpc/xmon: Fix compile error with PPC_8xx=y")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/YySE6FHiOcbWWR+9@work
Signed-off-by: Sasha Levin <sashal@kernel.org>

cxl: Fix refcount leak in cxl_calc_capp_routing

[ Upstream commit 1d09697ff22908ae487fc8c4fbde1811732be523 ]

of_get_next_parent() returns a node pointer with refcount incremented,
we should use of_node_put() on it when not need anymore.
This function only calls of_node_put() in normal path,
missing it in the error path.
Add missing of_node_put() to avoid refcount leak.

Fixes: f24be42aab37 ("cxl: Add psl9 specific code")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220605060038.62217-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/52xx: Fix a resource leak in an error handling path

[ Upstream commit 5836947613ef33d311b4eff6a32d019580a214f5 ]

The error handling path of mpc52xx_lpbfifo_probe() has a request_irq()
that is not balanced by a corresponding free_irq().

Add the missing call, as already done in the remove function.

Fixes: 3c9059d79f5e ("powerpc/5200: add LocalPlus bus FIFO device driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/dec1496d46ccd5311d0f6e9f9ca4238be11bf6a6.1643440531.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

macintosh/macio-adb: check the return value of ioremap()

[ Upstream commit dbaa3105736d4d73063ea0a3b01cd7fafce924e6 ]

The function ioremap() in macio_init() can fail, so its return value
should be checked.

Fixes: 36874579dbf4c ("[PATCH] powerpc: macio-adb build fix")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: Xie Shaowen <studentxswpy@163.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220802074148.3213659-1-studentxswpy@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

macintosh: fix possible memory leak in macio_add_one_device()

[ Upstream commit 5ca86eae55a2f006e6c1edd2029b2cacb6979515 ]

Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically. It
needs to be freed when of_device_register() fails. Call put_device() to
give up the reference that's taken in device_initialize(), so that it
can be freed in kobject_cleanup() when the refcount hits 0.

macio device is freed in macio_release_dev(), so the kfree() can be
removed.

Fixes: 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221104032551.1075335-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/fsl_pamu: Fix resource leak in fsl_pamu_probe()

[ Upstream commit 73f5fc5f884ad0c5f7d57f66303af64f9f002526 ]

The fsl_pamu_probe() returns directly when create_csd() failed, leaving
irq and memories unreleased.
Fix by jumping to error if create_csd() returns error.

Fixes: 695093e38c3e ("iommu/fsl: Freescale PAMU driver and iommu implementation.")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221121082022.19091-1-yuancan@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/amd: Fix pci device refcount leak in ppr_notifier()

[ Upstream commit 6cf0981c2233f97d56938d9d61845383d6eb227c ]

As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). So call it before returning from ppr_notifier()
to avoid refcount leak.

Fixes: daae2d25a477 ("iommu/amd: Don't copy GCR3 table root pointer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221118093604.216371-1-yangyingliang@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: pcf85063: Fix reading alarm

[ Upstream commit a6ceee26fd5ed9b5bd37322b1ca88e4548cee4a3 ]

If the alarms are disabled the topmost bit (AEN_*) is set in the alarm
registers. This is also interpreted in BCD number leading to this warning:
rtc rtc0: invalid alarm value: 2022-09-21T80:80:80

Fix this by masking alarm enabling and reserved bits.

Fixes: 05cb3a56ee8c ("rtc: pcf85063: add alarm support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220921074141.3903104-1-alexander.stein@ew.tq-group.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: snvs: Allow a time difference on clock register read

[ Upstream commit 0462681e207ccc44778a77b3297af728b1cf5b9f ]

On an iMX6ULL the following message appears when a wakealarm is set:

echo 0 > /sys/class/rtc/rtc1/wakealarm
rtc rtc1: Timeout trying to get valid LPSRT Counter read

This does not always happen but is reproducible quite often (7 out of 10
times). The problem appears because the iMX6ULL is not able to read the
registers within one 32kHz clock cycle which is the base clock of the
RTC. Therefore, this patch allows a difference of up to 320 cycles
(10ms). 10ms was chosen to be big enough even on systems with less cpu
power (e.g. iMX6ULL). According to the reference manual a difference is
fine:
- If the two consecutive reads are similar, the value is correct.
The values have to be similar, not equal.

Fixes: cd7f3a249dbe ("rtc: snvs: Add timeouts to avoid kernel lockups")
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco@dolcini.it>
Link: https://lore.kernel.org/r/20221106115915.7930-1-francesco@dolcini.it
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: Disable ACPI RTC event on removal

[ Upstream commit 83ebb7b3036d151ee39a4a752018665648fc3bd4 ]

Make cmos_do_remove() drop the ACPI RTC fixed event handler so as to
prevent it from operating on stale data in case the event triggers
after driver removal.

Fixes: 311ee9c151ad ("rtc: cmos: allow using ACPI for RTC alarm instead of HPET")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/2224609.iZASKD2KPV@kreacher
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: Rename ACPI-related functions

[ Upstream commit d13e9ad9f5146f066a5c5a1cc993d09e4fb21ead ]

The names of rtc_wake_setup() and cmos_wake_setup() don't indicate
that these functions are ACPI-related, which is the case, and the
former doesn't really reflect the role of the function.

Rename them to acpi_rtc_event_setup() and acpi_cmos_wake_setup(),
respectively, to address this shortcoming.

No intentional functional impact.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/3225614.44csPzL39Z@kreacher
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: Eliminate forward declarations of some functions

[ Upstream commit dca4d3b71c8a09a16951add656711fbd6f5bfbb0 ]

Reorder the ACPI-related code before cmos_do_probe() so as to eliminate
excessive forward declarations of some functions.

While at it, for consistency, add the inline modifier to the
definitions of empty stub static funtions and remove it from the
corresponding definitions of functions with non-empty bodies.

No intentional functional impact.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/13157911.uLZWGnKmhe@kreacher
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: Call rtc_wake_setup() from cmos_do_probe()

[ Upstream commit 375bbba09692fe4c5218eddee8e312dd733fa846 ]

To reduce code duplication, move the invocation of rtc_wake_setup()
into cmos_do_probe() and simplify the callers of the latter.

No intentional functional impact.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/2143522.irdbgypaU6@kreacher
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: Call cmos_wake_setup() from cmos_do_probe()

[ Upstream commit 508ccdfb86b21da37ad091003a4d4567709d5dfb ]

Notice that cmos_wake_setup() is the only user of acpi_rtc_info and it
can operate on the cmos_rtc variable directly, so it need not set the
platform_data pointer before cmos_do_probe() is called. Instead, it
can be called by cmos_do_probe() in the case when the platform_data
pointer is not set to implement the default behavior (which is to use
the FADT information as long as ACPI support is enabled).

Modify the code accordingly.

While at it, drop a comment that doesn't really match the code it is
supposed to be describing.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/4803444.31r3eYUQgx@kreacher
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: fix build on non-ACPI platforms

[ Upstream commit db4e955ae333567dea02822624106c0b96a2f84f ]

Now that rtc_wake_setup is called outside of cmos_wake_setup, it also need
to be defined on non-ACPI platforms.

Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20221018203512.2532407-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: Fix wake alarm breakage

[ Upstream commit 0782b66ed2fbb035dda76111df0954515e417b24 ]

Commit 4919d3eb2ec0 ("rtc: cmos: Fix event handler registration
ordering issue") overlooked the fact that cmos_do_probe() depended
on the preparations carried out by cmos_wake_setup() and the wake
alarm stopped working after the ordering of them had been changed.

Address this by partially reverting commit 4919d3eb2ec0 so that
cmos_wake_setup() is called before cmos_do_probe() again and moving
the rtc_wake_setup() invocation from cmos_wake_setup() directly to the
callers of cmos_do_probe() where it will happen after a successful
completion of the latter.

Fixes: 4919d3eb2ec0 ("rtc: cmos: Fix event handler registration ordering issue")
Reported-by: Zhang Rui <rui.zhang@intel.com>
Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/5887691.lOV4Wx5bFT@kreacher
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: cmos: Fix event handler registration ordering issue

[ Upstream commit 4919d3eb2ec0ee364f7e3cf2d99646c1b224fae8 ]

Because acpi_install_fixed_event_handler() enables the event
automatically on success, it is incorrect to call it before the
handler routine passed to it is ready to handle events.

Unfortunately, the rtc-cmos driver does exactly the incorrect thing
by calling cmos_wake_setup(), which passes rtc_handler() to
acpi_install_fixed_event_handler(), before cmos_do_probe(), because
rtc_handler() uses dev_get_drvdata() to get to the cmos object
pointer and the driver data pointer is only populated in
cmos_do_probe().

This leads to a NULL pointer dereference in rtc_handler() on boot
if the RTC fixed event happens to be active at the init time.

To address this issue, change the initialization ordering of the
driver so that cmos_wake_setup() is always called after a successful
cmos_do_probe() call.

While at it, change cmos_pnp_probe() to call cmos_do_probe() after
the initial if () statement used for computing the IRQ argument to
be passed to cmos_do_probe() which is cleaner than calling it in
each branch of that if () (local variable "irq" can be of type int,
because it is passed to that function as an argument of type int).

Note that commit 6492fed7d8c9 ("rtc: rtc-cmos: Do not check
ACPI_FADT_LOW_POWER_S0") caused this issue to affect a larger number
of systems, because previously it only affected systems with
ACPI_FADT_LOW_POWER_S0 set, but it is present regardless of that
commit.

Fixes: 6492fed7d8c9 ("rtc: rtc-cmos: Do not check ACPI_FADT_LOW_POWER_S0")
Fixes: a474aaedac99 ("rtc-cmos: move wake setup from ACPI glue into RTC driver")
Link: https://lore.kernel.org/linux-acpi/20221010141630.zfzi7mk7zvnmclzy@techsingularity.net/
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Link: https://lore.kernel.org/r/5629262.DvuYhMxLoT@kreacher
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: rtc-cmos: Do not check ACPI_FADT_LOW_POWER_S0

[ Upstream commit 6492fed7d8c95f53b0b804ef541324d924d95d41 ]

The ACPI_FADT_LOW_POWER_S0 flag merely means that it is better to
use low-power S0 idle on the given platform than S3 (provided that
the latter is supported) and it doesn't preclude using either of
them (which of them will be used depends on the choices made by user
space).

For this reason, there is no benefit from checking that flag in
use_acpi_alarm_quirks().

First off, it cannot be a bug to do S3 with use_acpi_alarm set,
because S3 can be used on systems with ACPI_FADT_LOW_POWER_S0 and it
must work if really supported, so the ACPI_FADT_LOW_POWER_S0 check is
not needed to protect the S3-capable systems from failing.

Second, suspend-to-idle can be carried out on a system with
ACPI_FADT_LOW_POWER_S0 unset and it is expected to work, so if setting
use_acpi_alarm is needed to handle that case correctly, it should be
set regardless of the ACPI_FADT_LOW_POWER_S0 value.

Accordingly, drop the ACPI_FADT_LOW_POWER_S0 check from
use_acpi_alarm_quirks().

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/12054246.O9o76ZdvQC@kreacher
Stable-dep-of: 83ebb7b3036d ("rtc: cmos: Disable ACPI RTC event on removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: idxd: Fix crc_val field for completion record

[ Upstream commit dc901d98b1fe6e52ab81cd3e0879379168e06daa ]

The crc_val in the completion record should be 64 bits and not 32 bits.

Fixes: 4ac823e9cd85 ("dmaengine: idxd: fix delta_rec and crc size field for completion record")
Reported-by: Nirav N Shah <nirav.n.shah@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20221111012715.2031481-1-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs/ntfs3: Fix slab-out-of-bounds read in ntfs_trim_fs

[ Upstream commit 557d19675a470bb0a98beccec38c5dc3735c20fa ]

Syzbot reports an out of bound access in ntfs_trim_fs.
The cause of this is using a loop termination condition that compares
window index (iw) with wnd->nbits instead of wnd->nwnd, due to which the
index used for wnd->free_bits exceeds the size of the array allocated.

Fix the loop condition.

Fixes: 3f3b442b5ad2 ("fs/ntfs3: Add bitmap")
Link: https://syzkaller.appspot.com/bug?extid=b892240eac461e488d51
Reported-by: syzbot+b892240eac461e488d51@syzkaller.appspotmail.com
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: tegra: Improve required rate calculation

[ Upstream commit f271946117dde2ca8741b8138b347b2d68e6ad56 ]

For the case where dev_pm_opp_set_rate() is called to set the PWM clock
rate, the requested rate is calculated as ...

required_clk_rate = (NSEC_PER_SEC / period_ns) << PWM_DUTY_WIDTH;

The above calculation may lead to rounding errors because the
NSEC_PER_SEC is divided by 'period_ns' before applying the
PWM_DUTY_WIDTH multiplication factor. For example, if the period is
45334ns, the above calculation yields a rate of 5646848Hz instead of
5646976Hz. Fix this by applying the multiplication factor before
dividing and using the DIV_ROUND_UP macro which yields the expected
result of 5646976Hz.

Fixes: 1d7796bdb63a ("pwm: tegra: Support dynamic clock frequency configuration")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

include/uapi/linux/swab: Fix potentially missing __always_inline

[ Upstream commit defbab270d45e32b068e7e73c3567232d745c60f ]

Commit bc27fb68aaad ("include/uapi/linux/byteorder, swab: force inlining
of some byteswap operations") added __always_inline to swab functions
and commit 283d75737837 ("uapi/linux/stddef.h: Provide __always_inline to
userspace headers") added a definition of __always_inline for use in
exported headers when the kernel's compiler.h is not available.

However, since swab.h does not include stddef.h, if the header soup does
not indirectly include it, the definition of __always_inline is missing,
resulting in a compilation failure, which was observed compiling the
perf tool using exported headers containing this commit:

In file included from /usr/include/linux/byteorder/little_endian.h:12:0,
                 from /usr/include/asm/byteorder.h:14,
                 from tools/include/uapi/linux/perf_event.h:20,
                 from perf.h:8,
                 from builtin-bench.c:18:
/usr/include/linux/swab.h:160:8: error: unknown type name `__always_inline'
static __always_inline __u16 __swab16p(const __u16 *p)

Fix this by replacing the inclusion of linux/compiler.h with
linux/stddef.h to ensure that we pick up that definition if required,
without relying on it's indirect inclusion. compiler.h is then included
indirectly, via stddef.h.

Fixes: 283d75737837 ("uapi/linux/stddef.h: Provide __always_inline to userspace headers")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Petr Vaněk <arkamar@atlas.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: usb: s2 WoL wakeup_count not incremented for USB->Eth devices

[ Upstream commit f7fc5b7090372fc4dd7798c874635ca41b8ba733 ]

The PHY's "wakeup_count" is not incrementing when waking from
WoL. The wakeup count can be found in sysfs at:
/sys/bus/platform/devices/rdb/*.usb-phy/power/wakeup_count.
The problem is that the system wakup event handler was being passed
the wrong "device" by the PHY driver.

Fixes: f1c0db40a3ad ("phy: usb: Add "wake on" functionality")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-3-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/rockchip: fix permission bits in page table entries v2

[ Upstream commit 7eb99841f340b80be0d0973b0deb592d75fb8928 ]

As pointed out in the corresponding downstream fix [0], the permission bits
of the page table entries are compatible between v1 and v2 of the IOMMU.
This is in contrast to the current mainline code that incorrectly assumes
that the read and write permission bits are switched. Fix the permission
bits by reusing the v1 bit defines.

[0] https://github.com/rockchip-linux/kernel/commit/e3bc123a2260145e34b57454da3db0edd117eb8e

Fixes: c55356c534aa ("iommu: rockchip: Add support for iommu v2")
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20221102063553.2464161-1-michael.riesch@wolfvision.net
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/sun50i: Fix flush size

[ Upstream commit 67a8a67f9eceb72e4c73d1d09ed9ab04f4b8e12d ]

Function sun50i_table_flush() takes number of entries as an argument,
not number of bytes. Fix that mistake in sun50i_dte_get_page_table().

Fixes: 4100b8c229b3 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-5-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/sun50i: Fix R/W permission check

[ Upstream commit eac0104dc69be50bed86926d6f32e82b44f8c921 ]

Because driver has enum type permissions and iommu subsystem has bitmap
type, we have to be careful how check for combined read and write
permissions is done. In such case, we have to mask both permissions and
check that both are set at the same time.

Current code just masks both flags but doesn't check that both are set.
In short, it always sets R/W permission, regardles if requested
permissions were RO, WO or RW. Fix that.

Fixes: 4100b8c229b3 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-4-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/sun50i: Consider all fault sources for reset

[ Upstream commit cef20703e2b2276aaa402ec5a65ec9a09963b83e ]

We have to reset masters for all faults - permissions, L1 fault or L2
fault. Currently it's done only for permissions. If other type of fault
happens, master is in locked up state. Fix that by really considering
all fault sources.

Fixes: 4100b8c229b3 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-3-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/sun50i: Fix reset release

[ Upstream commit 9ad0c1252e84dbc664f0462707182245ed603237 ]

Reset signal is asserted by writing 0 to the corresponding locations of
masters we want to reset. So in order to deassert all reset signals, we
should write 1's to all locations.

Current code writes 1's to locations of masters which were just reset
which is good. However, at the same time it also writes 0's to other
locations and thus asserts reset signals of remaining masters. Fix code
by writing all 1's when we want to deassert all reset signals.

This bug was discovered when working with Cedrus (video decoder). When
it faulted, display went blank due to reset signal assertion.

Fixes: 4100b8c229b3 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-2-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs/ntfs3: Harden against integer overflows

[ Upstream commit e001e60869390686809663c02bceb1d3922548fb ]

Smatch complains that the "add_bytes" is not to be trusted. Use
size_add() to prevent an integer overflow.

Fixes: be71b5cba2e6 ("fs/ntfs3: Add attrib operations")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

overflow: Implement size_t saturating arithmetic helpers

[ Upstream commit e1be43d9b5d0d1310dbd90185a8e5c7145dde40f ]

In order to perform more open-coded replacements of common allocation
size arithmetic, the kernel needs saturating (SIZE_MAX) helpers for
multiplication, addition, and subtraction. For example, it is common in
allocators, especially on realloc, to add to an existing size:

    p = krealloc(map->patch,
                 sizeof(struct reg_sequence) * (map->patch_regs + num_regs),
                 GFP_KERNEL);

There is no existing saturating replacement for this calculation, and
just leaving the addition open coded inside array_size() could
potentially overflow as well. For example, an overflow in an expression
for a size_t argument might wrap to zero:

    array_size(anything, something_at_size_max + 1) == 0

Introduce size_mul(), size_add(), and size_sub() helpers that
implicitly promote arguments to size_t and saturated calculations for
use in allocations. With these helpers it is also possible to redefine
array_size(), array3_size(), flex_array_size(), and struct_size() in
terms of the new helpers.

As with the check_*_overflow() helpers, the new helpers use __must_check,
though what is really desired is a way to make sure that assignment is
only to a size_t lvalue. Without this, it's still possible to introduce
overflow/underflow via type conversion (i.e. from size_t to int).
Enforcing this will currently need to be left to static analysis or
future use of -Wconversion.

Additionally update the overflow unit tests to force runtime evaluation
for the pathological cases.

Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Len Baker <len.baker@gmx.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Stable-dep-of: e001e6086939 ("fs/ntfs3: Harden against integer overflows")
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs/ntfs3: Avoid UBSAN error on true_sectors_per_clst()

[ Upstream commit caad9dd8792a2622737b7273cb34835fd9536cd2 ]

syzbot reported UBSAN error as below:

[   76.901829][ T6677] ================================================================================
[   76.903908][ T6677] UBSAN: shift-out-of-bounds in fs/ntfs3/super.c:675:13
[   76.905363][ T6677] shift exponent -247 is negative

This patch avoid this error.

Link: https://syzkaller.appspot.com/bug?id=b0299c09a14aababf0f1c862dd4ebc8ab9eb0179
Fixes: a3b774342fa7 (fs/ntfs3: validate BOOT sectors_per_clusters)
Cc: Author: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+35b87c668935bb55e666@syzkaller.appspotmail.com
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/siw: Fix pointer cast warning

[ Upstream commit 5244ca88671a1981ceec09c5c8809f003e6a62aa ]

The previous build fix left a remaining issue in configurations with
64-bit dma_addr_t on 32-bit architectures:

drivers/infiniband/sw/siw/siw_qp_tx.c: In function 'siw_get_pblpage':
drivers/infiniband/sw/siw/siw_qp_tx.c:32:37: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
32 | return virt_to_page((void *)paddr);
| ^

Use the same double cast here that the driver uses elsewhere to convert
between dma_addr_t and void*.

Fixes: 0d1b756acf60 ("RDMA/siw: Pass a pointer to virt_to_page()")
Link: https://lore.kernel.org/r/20221215170347.2612403-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bernard Metzler <bmt@zurich.ibm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf stat: Do not delay the workload with --delay

[ Upstream commit c587e77e100fa40eb6af10e00497c67acf493f33 ]

The -D/--delay option is to delay the measure after the program starts.
But the current code goes to sleep before starting the program so the
program is delayed too.  This is not the intention, let's fix it.

Before:

  $ time sudo ./perf stat -a -e cycles -D 3000 sleep 4
  Events disabled
  Events enabled

   Performance counter stats for 'system wide':

       4,326,949,337      cycles

         4.007494118 seconds time elapsed

  real 0m7.474s
  user 0m0.356s
  sys 0m0.120s

It ran the workload for 4 seconds and gave the 3 second delay.  So it
should skip the first 3 second and measure the last 1 second only.  But
as you can see, it delays 3 seconds and ran the workload after that for
4 seconds.  So the total time (real) was 7 seconds.

After:

  $ time sudo ./perf stat -a -e cycles -D 3000 sleep 4
  Events disabled
  Events enabled

   Performance counter stats for 'system wide':

       1,063,551,013      cycles

         1.002769510 seconds time elapsed

  real 0m4.484s
  user 0m0.385s
  sys 0m0.086s

The bug was introduced when it changed enablement of system-wide events
with a command line workload.  But it should've considered the initial
delay case.  The code was reworked since then (in bb8bc52e7578) so I'm
afraid it won't be applied cleanly.

Fixes: d0a0a511493d2695 ("perf stat: Fix forked applications enablement of counters")
Reported-by: Kevin Nomura <nomurak@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20221212230820.901382-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf stat: Refactor __run_perf_stat() common code

[ Upstream commit bb8bc52e75785af94b9ba079277547d50d018a52 ]

This extracts common code from the branches of the forks if-then-else.

enable_counters(), which was at the beginning of both branches of the
conditional, is now unconditional; evlist__start_workload() is extracted
to a different if, which enables making the common clocking code
unconditional.

Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Adrián Herrera Arcila <adrian.herrera@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/r/20220729161244.10522-1-adrian.herrera@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: c587e77e100f ("perf stat: Do not delay the workload with --delay")
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: fix null pointer dereferencing in power_supply_get_battery_info

[ Upstream commit 104bb8a663451404a26331263ce5b96c34504049 ]

when kmalloc() fail to allocate memory in kasprintf(), propname
will be NULL, strcmp() called by of_get_property() will cause
null pointer dereference.

So return ENOMEM if kasprintf() return NULL pointer.

Fixes: 3afb50d7125b ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: ab8500: Fix error handling in ab8500_charger_init()

[ Upstream commit c4d33381b134da188ccd1084aef21e2b8c3c422e ]

The ab8500_charger_init() returns the platform_driver_register() directly
without checking its return value, if platform_driver_register() failed,
all ab8500_charger_component_drivers are not unregistered.

Fix by unregister ab8500_charger_component_drivers when
platform_driver_register() failed.

Fixes: 1c1f13a006ed ("power: supply: ab8500: Move to componentized binding")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HSI: omap_ssi_core: Fix error handling in ssi_init()

[ Upstream commit 3ffa9f713c39a213a08d9ff13ab983a8aa5d8b5d ]

The ssi_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
ssi_pdriver is not unregistered.
Fix by unregister ssi_pdriver when the last platform_driver_register()
failed.

Fixes: 0fae198988b8 ("HSI: omap_ssi: built omap_ssi and omap_ssi_port into one module")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: z2_battery: Fix possible memleak in z2_batt_probe()

[ Upstream commit 955bee204f3dd307642c101b75e370662987e735 ]

If devm_gpiod_get_optional() returns error, the charger should be
freed before z2_batt_probe returns according to the context. We
fix it by just gotoing to 'err' branch.

Fixes: a3b4388ea19b ("power: supply: z2_battery: Convert to GPIO descriptors")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf symbol: correction while adjusting symbol

[ Upstream commit 6f520ce17920b3cdfbd2479b3ccf27f9706219d0 ]

perf doesn't provide proper symbol information for specially crafted
.debug files.

Sometimes .debug file may not have similar program header as runtime
ELF file. For example if we generate .debug file using objcopy
--only-keep-debug resulting file will not contain .text, .data and
other runtime sections. That means corresponding program headers will
have zero FileSiz and modified Offset.

Example: program header of text section of libxxx.so:

Type           Offset             VirtAddr           PhysAddr
               FileSiz            MemSiz              Flags  Align
LOAD        0x00000000003d3000 0x00000000003d3000 0x00000000003d3000
            0x000000000055ae80 0x000000000055ae80  R E    0x1000

Same program header after executing:
objcopy --only-keep-debug libxxx.so libxxx.so.debug

LOAD        0x0000000000001000 0x00000000003d3000 0x00000000003d3000
            0x0000000000000000 0x000000000055ae80  R E    0x1000

Offset and FileSiz have been changed.

Following formula will not provide correct value, if program header
taken from .debug file (syms_ss):

    sym.st_value -= phdr.p_vaddr - phdr.p_offset;

Correct program header information is located inside runtime ELF
file (runtime_ss).

Fixes: 2d86612aacb7805f ("perf symbol: Correct address for bss symbols")
Signed-off-by: Ajay Kaher <akaher@vmware.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Makhalov <amakhalov@vmware.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srivatsa S. Bhat <srivatsab@vmware.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Vasavi Sirnapalli <vsirnapalli@vmware.com>
Link: http://lore.kernel.org/lkml/1669198696-50547-1-git-send-email-akaher@vmware.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf trace: Handle failure when trace point folder is missed

[ Upstream commit 03e9a5d8eb552a1bf692a9c8a5ecd50f4e428006 ]

On Arm64 a case is perf tools fails to find the corresponding trace
point folder for system calls listed in the table 'syscalltbl_arm64',
e.g. the generated system call table contains "lookup_dcookie" but we
cannot find out the matched trace point folder for it.

We need to figure out if there have any issue for the generated system
call table, on the other hand, we need to handle the case when trace
point folder is missed under sysfs, this patch sets the flag
syscall::nonexistent as true and returns the error from
trace__read_syscall_info().

Another problem is for trace__syscall_info(), it returns two different
values if a system call doesn't exist: at the first time calling
trace__syscall_info() it returns NULL when the system call doesn't exist,
later if call trace__syscall_info() again for the same missed system
call, it returns pointer of syscall. trace__syscall_info() checks the
condition 'syscalls.table[id].name == NULL', but the name will be
assigned in the first invoking even the system call is not found.

So checking system call's name in trace__syscall_info() is not the right
thing to do, this patch simply checks flag syscall::nonexistent to make
decision if a system call exists or not, finally trace__syscall_info()
returns the consistent result (NULL) if a system call doesn't existed.

Fixes: b8b1033fcaa091d8 ("perf trace: Mark syscall ids that are not allocated to avoid unnecessary error messages")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: bpf@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221121075237.127706-4-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf trace: Use macro RAW_SYSCALL_ARGS_NUM to replace number

[ Upstream commit eadcab4c7a66e1df03d32da0db55d89fd9343fcc ]

This patch defines a macro RAW_SYSCALL_ARGS_NUM to replace the open
coded number '6'.

Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: bpf@vger.kernel.org
Link: https://lore.kernel.org/r/20221121075237.127706-2-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 03e9a5d8eb55 ("perf trace: Handle failure when trace point folder is missed")
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf trace: Return error if a system call doesn't exist

[ Upstream commit d4223e1776c30b2ce8d0e6eaadcbf696e60fca3c ]

When a system call is not detected, the reason is either because the
system call ID is out of scope or failure to find the corresponding path
in the sysfs, trace__read_syscall_info() returns zero. Finally, without
returning an error value it introduces confusion for the caller.

This patch lets the function trace__read_syscall_info() to return
-EEXIST when a system call doesn't exist.

Fixes: b8b1033fcaa091d8 ("perf trace: Mark syscall ids that are not allocated to avoid unnecessary error messages")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: bpf@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221121075237.127706-3-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: fix residue sysfs file in error handle route of __power_supply_register()

[ Upstream commit 5b79480ce1978864ac3f06f2134dfa3b6691fe74 ]

If device_add() succeeds, we should call device_del() when want to
get rid of it, so move it into proper jump symbol.

Otherwise, when __power_supply_register() returns fail and goto
wakeup_init_failed to exit, there is still residue device file in sysfs.
When attempt to probe device again, sysfs would complain as below:

sysfs: cannot create duplicate filename '/devices/platform/i2c/i2c-0/0-001c/power_supply/adp5061'
Call Trace:
dump_stack_lvl+0x68/0x85
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x1b1/0x1d0
kobject_add_internal+0x143/0x390
kobject_add+0x108/0x170

Fixes: 80c6463e2fa3 ("power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HSI: omap_ssi_core: fix possible memory leak in ssi_probe()

[ Upstream commit 1aff514e1d2bd47854dbbdf867970b9d463d4c57 ]

If ssi_add_controller() returns error, it should call hsi_put_controller()
to give up the reference that was set in hsi_alloc_controller(), so that
it can call hsi_controller_release() to free controller and ports that
allocated in hsi_alloc_controller().

Fixes: b209e047bc74 ("HSI: Introduce OMAP SSI driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HSI: omap_ssi_core: fix unbalanced pm_runtime_disable()

[ Upstream commit f5181c35ed7ba0ceb6e42872aad1334d994b0175 ]

In error label 'out1' path in ssi_probe(), the pm_runtime_enable()
has not been called yet, so pm_runtime_disable() is not needed.

Fixes: b209e047bc74 ("HSI: Introduce OMAP SSI driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: uvesafb: Fixes an error handling path in uvesafb_probe()

[ Upstream commit a94371040712031ba129c7e9d8ff04a06a2f8207 ]

If an error occurs after a successful uvesafb_init_mtrr() call, it must be
undone by a corresponding arch_phys_wc_del() call, as already done in the
remove function.

This has been added in the remove function in commit 63e28a7a5ffc
("uvesafb: Clean up MTRR code")

Fixes: 8bdb3a2d7df4 ("uvesafb: the driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: uvesafb: don't build on UML

[ Upstream commit 35b4f4d4a725cf8f8c10649163cd12aed509b953 ]

The uvesafb fbdev driver uses memory management information that is not
available on ARCH=um, so don't allow this driver to be built on UML.

Prevents these build errors:

../drivers/video/fbdev/uvesafb.c: In function ‘uvesafb_vbe_init’:
../drivers/video/fbdev/uvesafb.c:807:21: error: ‘__supported_pte_mask’ undeclared (first use in this function)
807 | if (__supported_pte_mask & _PAGE_NX) {
../drivers/video/fbdev/uvesafb.c:807:44: error: ‘_PAGE_NX’ undeclared (first use in this function)
807 | if (__supported_pte_mask & _PAGE_NX) {

Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-um@lists.infradead.org
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: geode: don't build on UML

[ Upstream commit 71c53e19226b0166ba387d3c590d0509f541a0a1 ]

The geode fbdev driver uses struct cpuinfo fields that are not present
on ARCH=um, so don't allow this driver to be built on UML.

Prevents these build errors:

In file included from ../arch/x86/include/asm/olpc.h:7:0,
                 from ../drivers/mfd/cs5535-mfd.c:17:
../arch/x86/include/asm/geode.h: In function ‘is_geode_gx’:
../arch/x86/include/asm/geode.h:16:24: error: ‘struct cpuinfo_um’ has no member named ‘x86_vendor’
  return ((boot_cpu_data.x86_vendor == X86_VENDOR_NSC) &&
../arch/x86/include/asm/geode.h:16:39: error: ‘X86_VENDOR_NSC’ undeclared (first use in this function); did you mean ‘X86_VENDOR_ANY’?
  return ((boot_cpu_data.x86_vendor == X86_VENDOR_NSC) &&
../arch/x86/include/asm/geode.h:17:17: error: ‘struct cpuinfo_um’ has no member named ‘x86’
   (boot_cpu_data.x86 == 5) &&
../arch/x86/include/asm/geode.h:18:17: error: ‘struct cpuinfo_um’ has no member named ‘x86_model’
   (boot_cpu_data.x86_model == 5));
../arch/x86/include/asm/geode.h: In function ‘is_geode_lx’:
../arch/x86/include/asm/geode.h:23:24: error: ‘struct cpuinfo_um’ has no member named ‘x86_vendor’
  return ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) &&
../arch/x86/include/asm/geode.h:23:39: error: ‘X86_VENDOR_AMD’ undeclared (first use in this function); did you mean ‘X86_VENDOR_ANY’?
  return ((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) &&
../arch/x86/include/asm/geode.h:24:17: error: ‘struct cpuinfo_um’ has no member named ‘x86’
   (boot_cpu_data.x86 == 5) &&
../arch/x86/include/asm/geode.h:25:17: error: ‘struct cpuinfo_um’ has no member named ‘x86_model’
   (boot_cpu_data.x86_model == 10));

Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: linux-um@lists.infradead.org
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: Andres Salomon <dilinger@queued.net>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: ep93xx-fb: Add missing clk_disable_unprepare in ep93xxfb_probe()

[ Upstream commit c84bf485a5aaf9aa0764a58832b7ef4375c29f03 ]

The clk_disable_unprepare() should be called in the error handling
of register_framebuffer(), fix it.

Fixes: 0937a7b3625d ("video: ep93xx: Prepare clock before using it")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: vermilion: decrease reference count in error path

[ Upstream commit 001f2cdb952a9566c77fb4b5470cc361db5601bb ]

pci_get_device() will increase the reference count for the returned
pci_dev. For the error path, we need to use pci_dev_put() to decrease
the reference count.

Fixes: dbe7e429fedb ("vmlfb: framebuffer driver for Intel Vermilion Range")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: via: Fix error in via_core_init()

[ Upstream commit 5886b130de953cfb8826f7771ec8640a79934a7f ]

via_core_init() won't exit the driver when pci_register_driver() failed.
Exit the viafb-i2c and the viafb-gpio in failed path to prevent error.

VIA Graphics Integration Chipset framebuffer 2.4 initializing
Error: Driver 'viafb-i2c' is already registered, aborting...
Error: Driver 'viafb-gpio' is already registered, aborting...

Fixes: 7582eb9be85f ("viafb: Turn GPIO and i2c into proper platform devices")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: pm2fb: fix missing pci_disable_device()

[ Upstream commit ed359a464846b48f76ea6cc5cd8257e545ac97f4 ]

Add missing pci_disable_device() in error path of probe() and remove() path.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: ssd1307fb: Drop optional dependency

[ Upstream commit 025e3b507a3a8e1ee96a3112bb67495c77d6cdb6 ]

Only a single out of three devices need a PWM, so from driver it's
optional. Moreover it's a single driver in the entire kernel that
currently selects PWM. Unfortunately this selection is a root cause
of the circular dependencies when we want to enable optional PWM
for some other drivers that select GPIOLIB.

Fixes: a2ed00da5047 ("drivers/video: add support for the Solomon SSD1307 OLED Controller")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thermal/drivers/qcom/lmh: Fix irq handler return value

[ Upstream commit 46a891e45be97c6781ac34f5ec777d69370e252b ]

After enough invocations the LMh irq is eventually reported as bad, because the
handler doesn't return IRQ_HANDLED, fix this.

Fixes: 53bca371cdf7 ("thermal/drivers/qcom: Add support for LMh driver")
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220316180322.88132-1-bjorn.andersson@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thermal/drivers/qcom/temp-alarm: Fix inaccurate warning for gen2

[ Upstream commit 8763f8acbf8aef22a2321d4c978cd078aa3b8f64 ]

On gen2 chips the stage2 threshold is not 140 degC but 125 degC.

Make the warning message clearer by using this variable and also by
including the temperature that was checked for.

Fixes: aa92b3310c55 ("thermal/drivers/qcom-spmi-temp-alarm: Add support for GEN2 rev 1 PMIC peripherals")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Amit Kucheria <amitk@kernel.org>
Link: https://lore.kernel.org/r/20221020145237.942146-1-luca.weiss@fairphone.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thermal/drivers/imx8mm_thermal: Validate temperature range

[ Upstream commit d37edc7370273306d8747097fafa62436c1cfe16 ]

Check against the upper temperature limit (125 degrees C) before
consider the temperature valid.

Fixes: 5eed800a6811 ("thermal: imx8mm: Add support for i.MX8MM thermal monitoring unit")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Link: https://lore.kernel.org/r/20221014073507.1594844-1-marcus.folkesson@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

samples: vfio-mdev: Fix missing pci_disable_device() in mdpy_fb_probe()

[ Upstream commit d1f0f50fbbbbca1e3e8157e51934613bf88f6d44 ]

Add missing pci_disable_device() in fail path of mdpy_fb_probe().
Besides, fix missing release functions in mdpy_fb_remove().

Fixes: cacade1946a4 ("sample: vfio mdev display - guest driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20221208013341.3999-1-shangxiaojing@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ksmbd: Fix resource leak in ksmbd_session_rpc_open()

[ Upstream commit bc044414fa0326a4e5c3c509c00b1fcaf621b5f4 ]

When ksmbd_rpc_open() fails then it must call ksmbd_rpc_id_free() to
undo the result of ksmbd_ipc_id_alloc().

Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>