iwlagn: wifi/bt coex configuration sequence

bt config command need to send before the init calibration command,
driver need to let uCode know that calibrations are being performed now
in order to assure antenna is not being taken to BT use during radio/dsp
reads/writes

Also, bt_coex_priorty_table command need to be send right after the
bt_config_command during init sequence. Followed by bt coex envelope
command to initialize and prepare uCode bt state machine

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add bt full concurrency support

Adding the bluetooth full concurrency support for WiFi/BT combo devices.

Driver should configure uCode to operate in "full concurrency" mode (via
LUT) if both conditions are met:
 - Antenna Coupling is more than 35dB
 - WiFi Channel Inhibition Request is hornored by BT Core

Currently, there is no antenna coupling information provided by uCode;
use module parameter to specified the antenna coupling in dB.

When in "full concurrency" mode, driver need to download different LUT
to uCode while sending bt configuration command; also, driver need to
configure the device operate in 1x1 while in full concurrency mode.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use antenna A only under high BT load

When bluetooth indicated high load, we should use
only antenna A in 2.4 GHz for management frames.
Add this condition to iwl_toggle_tx_ant() to make
sure it'll always be met. Note that scanning has
a separate way of forcing the antenna, because we
should scan on antenna A only regardless of BT
traffic load.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Relax uCode timeout/error checking for 6000g2b

Disable plcp error checking for 6000g2b devices, with wifi/bt coex;
this got trigger too often, disable for now until finding better
trigger point.

Also extend the firmware reload timer much longer for BT coex to make sure
there are will be no mistake to reload firmware too fast and too often.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: keep BT settings across restart

The BT SCO needs to be re-applied to the device,
while the traffic load just needs to be correct
in software.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: disable gen2b BT coexistence in IBSS

IBSS doesn't allow for coexistence, so it
should be disabled.

Additionally, disable reacting to the BT
profile notification when in IBSS mode,
it likely won't be sent by the device to
start with though.

Also, in IBSS mode, BT coexistence isn't as fully-featured
and we must use a single antenna only. So instead of
peppering the code with new checks, simply pretend
we are in high BT traffic load, which has the needed
effect of disabling antenna B use.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: reset BT when going down

When we turn off the device, reset BT
data so that we don't have outdated
information when we come up again.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: let bluetooth traffic load impact rate scale

Depending on the amount of bluetooth traffic,
using the shared antenna (antenna B) will have
adverse impact on both bluetooth and wireless
traffic. Add controls to improve the situation
by making rate scaling depend on the BT load.

When there's high bluetooth traffic load, there's
little point in trying to aggregate as BT traffic
would disrupt the aggregated frames all the time,
so simply don't start sessions then.

When BT traffic returns to lower levels, the rate
scaling will come here again automatically when
wifi traffic is high enough, and then it will be
able to successfully enable aggregation.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add BT notification support for bt coex

When advanced bt coex enabled, uCode will send bt status
notification to driver, here add support for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: set BT IGNORE for some frames

The BT ignore bit should be set when transmitting
auth, assoc response and eap frames.

Also, scanning should set the BT ignore bit for the
probe request transmission; Note that we only use
the non-shared antenna.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: implement advance BT config command

6000g2b hardware implements advance bluetooth coexist command,
implement base on the new API command strucutre.

Also increment the API 5 to support the advance BT/WIfi coex.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add 6000g2b BT coexist API

The new 6000g2b hardware requires a different
bluetooth coexist implementation on the host,
this adds the command/notification definitions
for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: comments cleanup

No code or function changes, just some cleanup work for
out-of-date comments

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: update out-of-date comments

No functional changes, update comments to match current file structure

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: cancel restart_work in ieee80211_unregister_hw

Unlike most other workqueue-tasks, the restart_work is
not scheduled onto mac80211's private per-interface
workqueue, but onto one of the system-wide workqueues.

Therefore the mac80211-stack has to cancel any pending
restarts, before destroying the shared device context
and handing back the memory. Otherwise - under very
unlucky circumstances - there could be a stale work-
item left, because some other kernel component might
have delayed the execution of ieee80211_restart_work
for too long.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54usb: fix off-by-one on !CONFIG_PM

The ISL3887 chip needs a USB reset, whenever the
usb-frontend module "p54usb" is reloaded.

This patch fixes an off-by-one bug, if the user
is running a kernel without the CONFIG_PM option
set and for some reason (e.g.: compat-wireless)
wants to switch between different p54usb modules.

Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: add missing phyrxchain setting and fix warning in RX core function

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: move include guard after the license

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: remove copyright contact person

As my nokia address doesn't work anymore, it's better just to remove the
copyright contact altogether. We have MODULE_AUTHOR() scripts for these
anyway.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: add info for include/linux/spi/wl12xx.h

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl12xx: change contact person for the include file

Luciano should be the contact person for the include/linux/spi/wl12xx.h file.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: update my email address

I use now my adurom.com address.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54spi: Kconfig option for config blob

This patch adds an Kconfig option, which allows the user
to select, whenever he/she wants to include a 4k blob for
generic calibration and interface values into the driver,
or cut the module size by about 15 to 20%.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: log descriptor chains at a new debug level

Descriptors are currently logged with ATH5K_DEBUG_RESET,
which isn't really apt, and also means we can't see just
the descriptor setup or just the resets.  Add a new
debug level just for that.

Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: trivial spelling fixes

Fix some comments:
    s/transmition/transmission/
    s/puting/putting/

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: trivial spelling fixes

Fix spelling and readability of a few lines of kernel doc:

    s/issueing/issuing/g
    s/approriate/appropriate/g
    s/supported by simply/supported simply by/
    s/IEEE80211_HW_BEACON_FILTERING/IEEE80211_HW_BEACON_FILTER/g

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix warning for un-used parameter

mesh_hdr only used when CONFIG_MAC80211_MESH is defined

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: update status in MAINTAINERS

Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: Fix walking past the end of the buffer

Fix walking past the end of the bitrate_table array
in the case when the loop counter == BITRATE_TABLE_SIZE.

Reported by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/mac80211: Use wiphy_<level>

Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix canceling monitor_recover timer

To make del_timer_sync() works we have to assure that timer function
does not rearm the timer. To achieve that we cancel timer with
STATUS_EXIT_PENDING bit set in __iwl{3945,}_down function.

Patch also fix priv->txq memory usage after free for iwl3945, because
it move timer cancellation before iwl3945_hw_txq_ctx_free(priv) is called.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Conflicts:
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-core.h

cfg80211: add some documentation

Add some documentation for cfg80211. I'm hoping some of
the regulatory documentation will be filled by somebody
more familiar with it, hint hint! :)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: do not spuriously call ieee80211_scan_completed

When a scan is aborted because the corresponding
virtual interface is removed, we may still later
attempt to tell mac80211 that the scan completed.
This is obviously wrong, since we already told it
that it was aborted, so don't do that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: do not check for AP mode for WEP keys

Even when we configure WEP keys in AP mode
ones without a station pointer are default
keys, so don't check for AP mode here.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add support for bluetooth coexistence.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_common: Move bt_stomp to common for sharing with ath9k_htc.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: some documentation fixes

The nl80211 documentation is currently never
generated, so problems have accumulated. Fix
most of the trivial ones.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix docbook

Fix a small problem in the documentation for
ieee80211_request_smps, and a now erroneous
inclusion of enum ieee80211_key_alg, which no
longer exists after the change to ciphers.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: wait for join command complete event

Poll for join command completion instead of waiting blindly for 10
msecs. There is a timeout of 100 msecs, if the command doesn't complete
by then, we return an error code.

Based on wl1271 patch 99d84c1de8fdf5f9b09f07fdbc628857a040bf8b
by Luciano Coelho.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: fix beacon filter table structure

The beacon filter table configuration ACX structure had certain elements
reversed, fix it to match TI driver.

Based on wl1271 patch 1937e742639c03a6fe77239c3003ce9602302117 by
Juuso Oikarinen.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: fix event handling mechanism

In case both A and B events occured simultaneously, current code
would only process A and clear both interrupts. Make it process both
events instead.

Based on wl1271 patches by Juuso Oikarinen:
1fd2794f36913992798184c464fe8f85753b13e0
13f2dc52c69bcca074cd12d4806953b2af45c386

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: add missing __packed modifier for some structs

Several acx and cmd structures are missing __packed modifier, add it.
This was noticed while comparing them with corresponding wl1271 code.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: move debug options into submenu

more debug options being added so it is useful to move them
into a submenu for ease of readability when using config commands
like make menuconfig and make xconfig

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: enable experimental ucode support

ucode firmware may need to be released as experimental for testing or
debugging. released ucode filenames have the API version as the last
component.  experimental ucode files will have that component be "exp"
and the fw_version string reported by ethtool will also contain the
string EXP to clearly identify this ucode from released ucode.
EXP is short for EXPERIMENTAL since fw_version has a max lenght on 32.

this capability is controlled by Kconfig and defaulted to not be used.

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove unused iwl_send_card_state function

iwl_send_card_state() is not being call from anywhere, remove it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: configurable ampdu factor and density

Add ampdu factor and density to .cfg, this allow both parameters
can be configure per device based.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: more generic name for rssi calc in iwlagn

Change the define to more generic naming to match _agn devices
since the rssi calculation are common function for 5000 series and up

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: additional parameter in REPLY_RX_PHY_CMD

Adding additional parameter in REPLY_RX_PHY_CMD, frame_time indicate the
frame's time on the air based on byte count and frame rate calculation

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: continue perform rate scale when error detected

If for some reason, the actual link command not matching neither
active nor search table; instead of return and not performing rate
scale, by-pass the data collection and continue the rate scale process.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: adjust starting action for rate scale

During rate scale, reset starting action after making action adjustment
to avoid the possibility of break out of loop too early.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: refactor iwl_setup_rxon_timing

All callers of iwl_setup_rxon_timing() also send
the command right away, so rename the function
to iwl_send_rxon_timing() and move the sending
into it. Also, some callers clear the data, this
can be done always and thus moved in as well.
Finally, there's no reason for the function to
acquire the spinlock, but it should be called
with the mutex held, so assert that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: cleanup iwl_set_rxon_channel()

Update outdated comments of iwl_set_rxon_channel() to reflect the
current signature. Also remove the unnecessary validation of the
channel. Those channel info are constructed in iwlwifi driver
and mac80211 will never modify the content of the struct. Also
everytime before this function is called the channel info has
been validated already (as a paranoid check).

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: avoid race condition in channel change

When iwl_mac_config() is called by mac80211, the channel pointer
hw->conf->channel can potentially change, resulting in mismatch
band and channel number when configuring RXON command. To avoid
this situation, save the channel pointer in local variables
and validate the channel before using it. Note that priv->mutex
is locked during the whole function so the local variables are safe.

Same change is applied to iwl_mac_channel_switch() since basically
it copies code from iwl_mac_config().

Also removed an outdated comment in the flow.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: do not call ieee80211_frequency_to_channel

A few cases in iwlwifi driver function ieee80211_frequency_to_channel()
is called to get channel number from center frequency. This is not needed
since the channel number is already saved in hw_value field of struct
ieee80211_channel in function iwlcore_init_geos(). So replace those function
calls with hw_value field of struct ieee80211_channel.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: make aggregation time limit configurable

By default, aggregation time limit is 4000 uSec, add the parameter to
.cfg
to allow this parameter can be configure per device base if needed.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: max/min aggregation time limit

Set the minimum and maximum for aggregation time limit in uSec.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: additional comments in iwl_cfg

No functional changes, just add additional comments to iwl_cfg structure

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove unused define

IWL_SIXTY_SECS is not been used, remove it

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Hostap: Fix "'ret' set but not used" warning message from GCC in hostap

 CC [M]  drivers/net/wireless/hostap/hostap_ioctl.o
drivers/net/wireless/hostap/hostap_ioctl.c: In function 'prism2_request_scan':
drivers/net/wireless/hostap/hostap_ioctl.c:1666:6: warning: variable 'ret' set but not used

Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix thermal throttling related power management operation

The current approach is very broken because it adds an
often-used code path that will not initialise "cmd" at all.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao.intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211-hwsim: allow configuring IBSS

It will not look standard-compliant in a sniffer
because because it doesn't
 * sync TSF
 * adjust the TSF in beacons
 * send beacons at TBTT
 * cancel beacons when another phy sends

However, it does allow testing the configuration
and parts of the mac80211 code for IBSS and as
such is still useful.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: move documentation books

This moves mac80211 documentation into a new
802.11 bookset and also adds a cfg80211 book
to the set. All of this is rather incomplete,
but it's easier to work with big code moving
as a separate patch.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: improve eeprom parser

Like other vendors, p54* devices have a checksum for
the EEPROM descriptor data. This patch enhances the
parser code to generate and verify the data fields,
before initializing the radio-chip on the card.

Note:
If you have to bootstrap an alternative EEPROM image
for your device and you don't know how to generate a
valid crc ccitt checksum, you should take a look at:
http://git.kernel.org/?p=linux/kernel/git/chr/p54tools.git

The "checksum" utility loads a binary p54 EEPROM blob
(use the -f switch, to skip the check) and applies
the correct crc automatically.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54spi: fix eeprom checksum

This patch corrects the bogus descriptor checksum of our
Nokia N8XX EEPROM blob.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: Implement RX core state setting for rev.2 and earlier PHYs

Rev.3+ support coming in a later patch.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: Implement MAC PHY clock set

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: Fix typo in function name (gain_crtl -> gain_ctrl)

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: Implement Host Flags write during device init

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: separate thermal throttling function

"Thermal Throttling" is an advance feature which only available for
newer _agn devices. Move from iwl-core to iwl-agn for better code
organization.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/wl12xx: Use available error codes

Error codes are stored in ret, but the return value is always 0.  Return
ret instead.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
local idexpression x;
constant C;
@@

if (...) { ...
  x = -C
  ... when != x
(
  return <+...x...+>;
|
  return NULL;
|
  return;
|
* return ...;
)
}
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/wl12xx: Use available error codes

In each case, error codes are stored in ret, but the return value is always
0.  Return ret instead.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
local idexpression x;
constant C;
@@

if (...) { ...
  x = -C
  ... when != x
(
  return <+...x...+>;
|
  return NULL;
|
  return;
|
* return ...;
)
}
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: don't enable probe request rx for STAs

AR5K_RX_FILTER_PROBEREQ enables reception of probe requests,
but the filter flag FIF_BCN_PRBRESP_PROMISC is actually about
receiving beacons and probe _responses_, so we shouldn't
turn on the filter when scanning.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: remove all mention of monitor iftype

Monitor interfaces are never seen by the driver so these
cases are never reached.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: remove monitor check in receive_frame_ok filter

Monitor interfaces are never seen by the driver, so tests based on
that opmode don't make sense.  Also, we already pass all mic
failure packets.

Consequently this code is actually accepting any frames with just
crypto errors and rejecting those with CRC, FIFO, and PHY errors for
all interface types.  Adjust the code and comment accordingly.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: clean up some comments

This fixes a few misspellings, word repetitions, and some grammar
nits in ath5k comments.  No code changes.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: remove own (wrong) IEEE80211_MAX_LEN

Use the version already supplied in include/linux/ieee80211.h.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: rename ath5k_hw_set_associd to _set_bssid

Although the named function also sets the aid, its main
purpose is configuring the bssid and we use that
everywhere else.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/mac80211: extensible frame processing

Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.

With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove unused don't-encrypt flag

When MFP is disabled, action frames will not
be encrypted since they are management frames
and the only management frames that can then
be encrypted are authentication frames.

Therefore, setting the don't-encrypt flag on
action frames is unnecessary.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: mark ieee80211_hdrlen const

This function analyses only its single, value-passed
argument, and has no side effects. Thus it can be
const, which makes mac80211 smaller, for example:

   text    data     bss     dec     hex filename
 362518   16720     884  380122   5ccda mac80211.ko (before)
 362358   16720     884  379962   5cc3a mac80211.ko (after)

a 160 byte saving in text size, and an optimisation
because the function won't be called as often.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use long monitor timer for 5300 series

For 5000 series of devices, use long monitor timer to check
stuck tx queues.

This modification apply to all the 5000 series including 5300 and others.

Cc: stable@kernel.org [2.6.35]
Reported-by: drago01 <drago01@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless: Restore upper case words in wiphy_<level> messages

Commit c96c31e499b70964cfc88744046c998bb710e4b8
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case.  Restore the original case.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix 3945 filter flags

Applying the filter flags directly as done since

commit 3474ad635db371b0d8d0ee40086f15d223d5b6a4
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Apr 29 04:43:05 2010 -0700

    iwlwifi: apply filter flags directly

broke 3945 under some unknown circumstances, as
reported by Alex.

Since I want to keep the direct application of
filter flags on iwlagn, duplicate the code into
both 3945 and agn and remove committing the
RXON that broke things from the 3945 version.

Cc: stable@kernel.org [2.6.35]
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2100: don't sync status queue entries

These are allocated with pci_alloc_consistent, so calling
pci_dma_sync_single_for_cpu is incorrect usage of the API.  Remove this
misuse and consequently avoid the following backtrace:

WARNING: at lib/dma-debug.c:902 check_sync+0xce/0x43a()
Hardware name: 2373HU6
ipw2100 0000:02:02.0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x0000000034e88008] [size=8 bytes]
Modules linked in: microcode ipw2100(+) snd_seq_device ppdev libipw nsc_ircc snd_pcm lib80211 video output irda parport_pc cfg80211 parport thinkpad_acpi e1000 iTCO_wdt crc_ccitt snd_timer iTCO_vendor_support snd i2c_i801 pcspkr rfkill soundcore joydev snd_page_alloc yenta_socket radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core [last unloaded: scsi_wait_scan]
Pid: 0, comm: swapper Tainted: G        W   2.6.35-wl+ #8
Call Trace:
 [<c043aa42>] warn_slowpath_common+0x6a/0x7f
 [<c05d252a>] ? check_sync+0xce/0x43a
 [<c043aaca>] warn_slowpath_fmt+0x2b/0x2f
 [<c05d252a>] check_sync+0xce/0x43a
 [<c046189a>] ? print_lock_contention_bug+0x11/0xb2
 [<c05d2b6f>] debug_dma_sync_single_for_cpu+0x47/0x49
 [<c06cbd3c>] ? ehci_irq+0x31/0x331
 [<f82a224a>] ? ipw2100_irq_tasklet+0x24/0x5e9 [ipw2100]
 [<f82a224a>] ? ipw2100_irq_tasklet+0x24/0x5e9 [ipw2100]
 [<f82a221d>] pci_dma_sync_single_for_cpu.clone.1+0x42/0x4b [ipw2100]
 [<f82a23a2>] ipw2100_irq_tasklet+0x17c/0x5e9 [ipw2100]
 [<c043fd87>] tasklet_action+0x78/0xcb
 [<c0440293>] __do_softirq+0xc4/0x183
 [<c044038d>] do_softirq+0x3b/0x5f
 [<c04404d0>] irq_exit+0x3a/0x6d
 [<c0404423>] do_IRQ+0x8b/0x9f
 [<c04038b5>] common_interrupt+0x35/0x3c
 [<c062ecfa>] ? acpi_idle_enter_simple+0xfe/0x13c
 [<c045007b>] ? exit_itimers+0x2d/0x73
 [<c062ecfc>] ? acpi_idle_enter_simple+0x100/0x13c
 [<c070bf10>] cpuidle_idle_call+0x78/0xdc
 [<c040251c>] cpu_idle+0x9b/0xb7
 [<c07b1dd2>] rest_init+0xa6/0xab
 [<c0a4b96d>] start_kernel+0x389/0x38e
 [<c0a4b0c9>] i386_start_kernel+0xc9/0xd0

Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/libertas/cfg.c: needs sched.h

i386 allmodconfig:

drivers/net/wireless/libertas/cfg.c: In function 'lbs_scan_worker':
drivers/net/wireless/libertas/cfg.c:722: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once
drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.)
drivers/net/wireless/libertas/cfg.c: In function 'lbs_cfg_connect':
drivers/net/wireless/libertas/cfg.c:1267: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function 'signal_pending'
drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function 'schedule_timeout'

So wait.h has a dependency on sched.h, but doesn't include sched.h.  This
patch doesn't fix that.

Cc: Dan Williams <dcbw@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: check if WEP is available for shared key auth

When shared key auth is requested, cfg80211
should verify that the device is capable of
WEP crypto which is required.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: dont advertise WEP if unavailable

When WEP is unavailable, don't advertise it
to cfg80211.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove unused status flag checks

The decryption code verifies whether or not
a given frame was decrypted and verified by
hardware. This is unnecessary, as the crypto
RX handler already does it long before the
decryption code is even invoked, so remove
that code to avoid confusion.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: move key tfm setup

There's no need to keep separate if statements
for setting up the CCMP/AES-CMAC tfm structs;
move that into the existing switch statement.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: use cipher suite selectors

Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: [spi] use common firmware request helper and new firmware locations

linux-firmware puts libertas firmware in /libertas.  Fix the driver to
look there first, but fall back to the old firmware names if the new
ones don't exist.  Add preference for newer firmware versions too.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: [sdio] use common firmware request helper and new firmware locations

linux-firmware puts libertas firmware in /libertas.  Fix the driver to
look there first, but fall back to the old firmware names if the new
ones don't exist.  Add preference for newer firmware versions too.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: [cs] use common firmware request helper and new firmware locations

linux-firmware puts libertas firmware in /libertas.  Fix the driver to
look there first, but fall back to the old firmware names if the new
ones don't exist.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add two-stage firmware request helper

SDIO, GSPI, and CS all use 2-stage firmware and the loading
process and logic should be the same.  Allow module parameters
to override the automatic firmware choice, otherwise just walk
the bus driver's firmware table and pick out the first firmware
pair that exists for the given model.

Some special care is taken to allow overriding of just the helper
or the main firmware, but let the other of the pair be chosen
automatically.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: [usb] use new firmware locations

Look for firmware where the linux-firmware tree actually puts it, but
fall back to original firmware name & location when the new location
doesn't exist.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove ieee80211_rx_status from rt2x00_dev

rt2x00 was keeping a copy of ieee80211_rx_status embedded
into the rt2x00_dev structure. For each RX frame, this structure
was copied into the skb->cb where mac80211 would handle it further.

However at the moment only the fields current band, and frequency
were updated. Whereas the band was already provided directly within
the rt2x00_dev structure. Save a memcpy action, and reduce memory
a bit, by adding a curr_freq field to rt2x00_dev, and completely
remove the ieee80211_rx_status structure from rt2x00_dev.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Update comments regarding TXWI and TX_STA_FIFO

Add some comments about the TXWI fields and the TX_STA_FIFO register.
Especially describe the relationship between the TXWI field PACKETID
and the PID field in the TX_STA_FIFO register.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement TX status reporting for rt2800usb

The TX_STA_FIFO register which is used for per-frame TX frame
status reporting is also valid on rt2800usb. We can move the
rt2800pci_txdone function into rt2800lib where it can also
be used by rt2800usb.

rt2800usb needs to overwrite the txdone work handler to
a different function.

Both rt2800usb as rt2800_txdone need to take into account
that IO failures can occur while uploading the URB, which
means that when obtaining the new entry the IO status must
be checked.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Request TXWI pointer from driver

The only reason why the write_tx_data callback function
is needed inside the driver, is because the location of
the TXWI descriptor is different on PCI and USB hardware.
Except for the beacon, where the TXWI is always at the
start of the SKB buffer.

In both cases the drivers write_tx_data function only
wrap around the function rt2800_write_txwi. Move write_tx_data
completely into the rt2800lib library, and add a callback
function to obtain the TXWI pointer.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>