review.tizen.org Git - platform/kernel/linux-rpi.git/log

drm/vmwgfx: Fix mob cursor allocation race

Writes to SVGA_REG_CURSOR_MOBID did not wait for the buffers to be fully
populated. This sometimes results in the device not being aware of
the buffer when the cursor mob register was written.
Properly wait for the buffer to be fully populated before setting it
as a cursor mob.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 485d98d472d5 ("drm/vmwgfx: Add support for CursorMob and CursorBypass 4")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220318174332.440068-3-zack@kde.org

drm/vmwgfx: Fix an invalid read

vmw_move assumed that buffers to be moved would always be
vmw_buffer_object's but after introduction of new placement for mob
pages that's no longer the case.
The resulting invalid read didn't have any practical consequences
because the memory isn't used unless the object actually is a
vmw_buffer_object.
Fix it by moving the cast to the spot where the results are used.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: f6be23264bba ("drm/vmwgfx: Introduce a new placement for MOB page tables")
Reported-by: Chuck Lever III <chuck.lever@oracle.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220318174332.440068-2-zack@kde.org

fbdev: defio: fix the pagelist corruption

Easily hit the below list corruption:
==
list_add corruption. prev->next should be next (ffffffffc0ceb090), but
was ffffec604507edc8. (prev=ffffec604507edc8).
WARNING: CPU: 65 PID: 3959 at lib/list_debug.c:26
__list_add_valid+0x53/0x80
CPU: 65 PID: 3959 Comm: fbdev Tainted: G U
RIP: 0010:__list_add_valid+0x53/0x80
Call Trace:
<TASK>
fb_deferred_io_mkwrite+0xea/0x150
do_page_mkwrite+0x57/0xc0
do_wp_page+0x278/0x2f0
__handle_mm_fault+0xdc2/0x1590
handle_mm_fault+0xdd/0x2c0
do_user_addr_fault+0x1d3/0x650
exc_page_fault+0x77/0x180
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
RIP: 0033:0x7fd98fc8fad1
==

Figure out the race happens when one process is adding &page->lru into
the pagelist tail in fb_deferred_io_mkwrite(), another process is
re-initializing the same &page->lru in fb_deferred_io_fault(), which is
not protected by the lock.

This fix is to init all the page lists one time during initialization,
it not only fixes the list corruption, but also avoids INIT_LIST_HEAD()
redundantly.

V2: change "int i" to "unsigned int i" (Geert Uytterhoeven)

Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Fixes: 105a940416fc ("fbdev/defio: Early-out if page is already enlisted")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220318005003.51810-1-chuansheng.liu@intel.com

drm/panel-edp: add LQ140M1JW46 edp panel entry

Add panel identification entry for the sharp LQ140M1JW46 eDP panel
with power sequencing delay information.

Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1647452154-16361-5-git-send-email-quic_sbillaka@quicinc.com

dt-bindings: display/panel: Add Leadtek ltk035c5444t

Add binding for the leadtek ltk035c5444t, which is a 640x480
mipi-dbi over spi / 24-bit RGB panel based on the newvision
NV03052C chipset.

It is found in the Anbernic RG350M mips handheld.

Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311170240.173846-5-cbranchereau@gmail.com

fbdev: Fix cfb_imageblit() for arbitrary image widths

Commit 0d03011894d2 ("fbdev: Improve performance of cfb_imageblit()")
broke cfb_imageblit() for image widths that are not aligned to 8-bit
boundaries. Fix this by handling the trailing pixels on each line
separately. The performance improvements in the original commit do not
regress by this change.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 0d03011894d2 ("fbdev: Improve performance of cfb_imageblit()")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220313192952.12058-3-tzimmermann@suse.de

fbdev: Fix sys_imageblit() for arbitrary image widths

Commit 6f29e04938bf ("fbdev: Improve performance of sys_imageblit()")
broke sys_imageblit() for image width that are not aligned to 8-bit
boundaries. Fix this by handling the trailing pixels on each line
separately. The performance improvements in the original commit do not
regress by this change.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 6f29e04938bf ("fbdev: Improve performance of sys_imageblit()")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220313192952.12058-2-tzimmermann@suse.de

drm/gma500: Cosmetic cleanup of irq code

Use the gma_ prefix instead of psb_ since the code is common for all
chips. Various coding style fixes. Removal of unused code. Removal of
duplicate function declarations.

Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317092555.17882-4-patrik.r.jakobsson@gmail.com

drm/gma500: Don't store crtc_funcs in psb_ops

The drm_crtc_funcs are all generic and no chip specific functions are
necessary. We can therefore directly put gma_crtc_funcs into the
drm_crtc.

Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317092555.17882-3-patrik.r.jakobsson@gmail.com

drm/gma500: Move gma_intel_crtc_funcs into gma_display.c

All functions live in gma_display.c already so move the vtable. Also
shorten the name to gma_crtc_funcs.

Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317092555.17882-2-patrik.r.jakobsson@gmail.com

drm/gma500: Remove unused declarations and other cruft

Most of these are old leftovers from one of the driver merges. This is
all dead code.

Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317092555.17882-1-patrik.r.jakobsson@gmail.com

drm/vc4: add tracepoints for CL submissions

Trace submit_cl_ioctl and related IRQs for CL submission and bin/render
jobs execution. It might be helpful to get a rendering timeline and
track job throttling.

Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220201212651.zhltjmaokisffq3x@mail.igalia.com

drm/ssd130x: Reduce temporary buffer sizes

ssd130x_clear_screen() allocates a temporary buffer sized to hold one
byte per pixel, while it only needs to hold one bit per pixel.

ssd130x_fb_blit_rect() allocates a temporary buffer sized to hold one
byte per pixel for the whole frame buffer, while it only needs to hold
one bit per pixel for the part that is to be updated.
Pass dst_pitch to drm_fb_xrgb8888_to_mono(), as we have already
calculated it anyway.

Fixes: a61732e808672cfa ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-5-geert@linux-m68k.org

drm/ssd130x: Fix rectangle updates

The rectangle update functions ssd130x_fb_blit_rect() and
ssd130x_update_rect() do not behave correctly when x1 != 0 or y1 !=
0, or when y1 or y2 are not aligned to display page boundaries.
E.g. when used as a text console, only the first line of text is shown
on the display.

  1. The buffer passed by ssd130x_fb_blit_rect() points to the first
     byte of monochrome bitmap data, and thus has its origin at (x1,
     y1), while ssd130x_update_rect() assumes it is at (0, 0).
     Fix ssd130x_update_rect() by changing the vertical and horizontal
     loop ranges, and adding the offsets only when needed.

  2. In ssd130x_fb_blit_rect(), align y1 and y2 to the display page
     boundaries before doing the color conversion, so the full page
     is converted and updated.
     Remove the correction for an unaligned y1 from
     ssd130x_update_rect(), and add a check to make sure y1 is aligned.

Fixes: a61732e808672cfa ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-4-geert@linux-m68k.org

drm/format-helper: Fix XRGB888 to monochrome conversion

The conversion functions drm_fb_xrgb8888_to_mono() and
drm_fb_gray8_to_mono_line() do not behave correctly when the
horizontal boundaries of the clip rectangle are not multiples of 8:
  a. When x1 % 8 != 0, the calculated pitch is not correct,
  b. When x2 % 8 != 0, the pixel data for the last byte is wrong.

Simplify the code and fix (a) by:
  1. Removing start_offset, and always storing the first pixel in the
     first bit of the monochrome destination buffer.
     Drivers that require the first pixel in a byte to be located at an
     x-coordinate that is a multiple of 8 can always align the clip
     rectangle before calling drm_fb_xrgb8888_to_mono().
     Note that:
       - The ssd130x driver does not need the alignment, as the
monochrome buffer is a temporary format,
       - The repaper driver always updates the full screen, so the clip
rectangle is always aligned.
  2. Passing the number of pixels to drm_fb_gray8_to_mono_line(),
     instead of the number of bytes, and the number of pixels in the
     last byte.

Fix (b) by explicitly setting the target bit, instead of always setting
bit 7 and shifting the value in each loop iteration.

Remove the bogus pitch check, which operates on bytes instead of pixels,
and triggers when e.g. flashing the cursor on a text console with a font
that is 8 pixels wide.

Drop the confusing comment about scanlines, as a pitch in bytes always
contains a multiple of 8 pixels.

While at it, use the drm_rect_height() helper instead of open-coding the
same operation.

Update the comments accordingly.

Fixes: bcf8b616deb87941 ("drm/format-helper: Add drm_fb_xrgb8888_to_mono_reversed()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-3-geert@linux-m68k.org

drm/format-helper: Rename drm_fb_xrgb8888_to_mono_reversed()

There is no "reversed" handling in drm_fb_xrgb8888_to_mono_reversed():
the function just converts from color to grayscale, and reduces the
number of grayscale levels from 256 to 2 (i.e. brightness 0-127 is
mapped to 0, 128-255 to 1). All "reversed" handling is done in the
repaper driver, where this function originated.

Hence make this clear by renaming drm_fb_xrgb8888_to_mono_reversed() to
drm_fb_xrgb8888_to_mono(), and documenting the black/white pixel
mapping.

Fixes: bcf8b616deb87941 ("drm/format-helper: Add drm_fb_xrgb8888_to_mono_reversed()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-2-geert@linux-m68k.org

drm/doc: Clarify what ioctls can be used on render nodes

The documentation for render nodes indicates that only "PRIME-related"
ioctls are valid on render nodes, but the documentation does not clarify
what that means. If the reader is not familiar with PRIME, they may
beleive this to be only the ioctls with "PRIME" in the name and not other
ioctls such as set of syncobj ioctls. Clarify the situation for the
reader by referencing where the reader will find a current list of valid
ioctls.

Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1646667156-16366-1-git-send-email-quic_jhugo@quicinc.com

drm/nouveau: Fix spelling mistake "endianess" -> "endianness"

There is a spelling mistake in a nvdev_error error message. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315221929.2959700-1-colin.i.king@gmail.com

drm/gma500: Move GTT memory-range setup into helper

Move the setup code for GTT/GATT memory ranges into a new helper and
call the function from psb_gtt_init() and psb_gtt_resume(). Removes
code duplication.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-13-tzimmermann@suse.de

drm/gma500: Move GTT enable and disable code into helpers

Move the code for enabling and disabling the GTT into helpers and call
the functions in psb_gtt_init(), psb_gtt_fini() and psb_gtt_resume().
Removes code duplication.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-12-tzimmermann@suse.de

drm/gma500: Move GEM memory management functions to gem.c

Move GEM functions from gtt.c to gem.c. Adapt some names. No
functional changes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-11-tzimmermann@suse.de

drm/gma500: Inline psb_gtt_restore()

Inline psb_gtt_restore() into its only caller in power.c.

Perform the GTT restoration in psb_gem_mm_resume(). The restoration
step is part of GEM anyway and will be moved over at some point.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-10-tzimmermann@suse.de

drm/gma500: Split GTT init/resume/fini into GTT and GEM functions

The GTT init, fini and resume functions contain both, GTT and GEM,
code. Split each into a separate GTT and a GEM function. The GEM
code is responsible for mmap_mutex and the stolen memory area. The
rest of the functionality is left in GTT functions.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-9-tzimmermann@suse.de

drm/gma500: Cleanup GTT uninit and error handling

Replace psb_gtt_takedown() with finalizer function that is only called
for unloading the driver. Use roll-back pattern for error handling in
psb_gtt_init() and _resume(). Also fixes a bug where vmap_addr was never
unmapped.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-8-tzimmermann@suse.de

drm/gma500: Move GTT resume logic out of psb_gtt_init()

The current implementation of psb_gtt_init() also does resume
handling. Move the resume code into its own helper.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-7-tzimmermann@suse.de

drm/gma500: Move GTT setup and restoration into helper funtions

The GTT init and restore functions contain logic to populate the
GTT entries. Move the code into helper functions.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-6-tzimmermann@suse.de

drm/gma500: Remove struct psb_gtt.sem sempahore

The semaphore at struct psb_mmu_driver.sem protects access to the MMU
fields. Additional locking with struct psb_gtt.sem is unnecessary. Remove
the field and related code.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-5-tzimmermann@suse.de

drm/gma500: Move GTT locking into GTT helpers

Acquire the GTT mutex in psb_gtt_{insert,remove}_pages(). Remove
locking from callers. Also remove the GTT locking around the resume
code. Resume does not run concurrently with other GTT operations.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-4-tzimmermann@suse.de

drm/gma500: Acquire reservation lock for GEM objects

Protect concurrent access to struct psb_gem_object by acquiring
the GEM object's reservation lock; as it's supposed to be. The
use of the GTT mutex can now be moved into GTT code.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-3-tzimmermann@suse.de

drm/gma500: Remove struct psb_gem_object.npage

Calculate the number of pages in the BO's backing storage from
the size. Remove the npage field.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308195222.13471-2-tzimmermann@suse.de

drm/solomon: Make DRM_SSD130X depends on MMU

WARNING: unmet direct dependencies detected for DRM_GEM_SHMEM_HELPER
  Depends on [n]: HAS_IOMEM [=y] && DRM [=m] && MMU [=n]
  Selected by [m]:
  - DRM_SSD130X [=m] && HAS_IOMEM [=y] && DRM [=m]

DRM_GEM_SHMEM_HELPER depends on MMU, DRM_SSD130X should also depends on MMU.

Fixes: a61732e80867 ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220312063437.19160-1-yuehaibing@huawei.com

drm/blend: fix typo in the comment

The documentation for drm_rotation_simplify() uses DRM_MODE_ROTATE_X,
while it's clear the comment should mention DRM_MODE_REFLECT_X
instead. The example passes all flags except the DRM_MODE_REFLECT_X as
supported and expects to eliminate this flag.

Fixes: c2c446ad2943 ("drm: Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ to UAPI")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220316074648.7009-1-dmitry.baryshkov@linaro.org

drm/panel: Use drm_mode_duplicate()

Replace the hand rolled drm_mode_duplicate() with the
real thing.

@is_dup@
@@
drm_mode_duplicate(...)
{ ... }

@depends on !is_dup@
expression dev, oldmode;
identifier newmode;
@@
- newmode = drm_mode_create(dev);
+ newmode = drm_mode_duplicate(dev, oldmode);
...
- drm_mode_copy(newmode, oldmode);

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-21-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>

drm/imx: Use drm_mode_duplicate()

Replace the hand rolled drm_mode_duplicate() with the
real thing.

@is_dup@
@@
drm_mode_duplicate(...)
{ ... }

@depends on !is_dup@
expression dev, oldmode;
identifier newmode;
@@
- newmode = drm_mode_create(dev);
+ newmode = drm_mode_duplicate(dev, oldmode);
...
- drm_mode_copy(newmode, oldmode);

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-10-ville.syrjala@linux.intel.com
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>

drm/bridge: Use drm_mode_copy()

struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.

Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.

Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.

@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}

@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)

@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)

@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode

Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-7-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

drm: Add drm_mode_init()

Add a variant of drm_mode_copy() that explicitly clears out
the list head of the destination mode. Helpful to guarantee
we don't have stack garbage left in there for on-stack modes.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218100403.7028-2-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>

drm/vmwgfx: Stop using surface dma commands on most configurations

Initial version of guest backed objects in the host had some performance
issues that made using surface-dma's instead of direct copies faster.
Surface dma's force a migration to vram which at best is slow and at
worst is impossible (e.g. on svga3 where there's not enough vram
to migrate fb's to it).

Slowly migrate away from surface dma's to direct copies by limiting
their usage to systems with more than 32MB of vram.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-9-zack@kde.org

drm/vmwgfx: Implement MSI/MSI-X support for IRQs

SVGAv3 deprecates legacy interrupts and adds support for MSI/MSI-X. With
MSI the driver visible side remains largely unchanged but with MSI-X
each interrupt gets delivered on its own vector.

Add support for MSI/MSI-X while preserving the old functionality for
SVGAv2. Code between the SVGAv2 and SVGAv3 is exactly the same, only
the number of available vectors changes, in particular between legacy
and MSI-X interrupts.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307162412.1183049-1-zack@kde.org

drm/vmwgfx: Initialize drm_mode_fb_cmd2

Transition to drm_mode_fb_cmd2 from drm_mode_fb_cmd left the structure
unitialized. drm_mode_fb_cmd2 adds a few additional members, e.g. flags
and modifiers which were never initialized. Garbage in those members
can cause random failures during the bringup of the fbcon.

Initializing the structure fixes random blank screens after bootup due
to flags/modifiers mismatches during the fbcon bring up.

Fixes: dabdcdc9822a ("drm/vmwgfx: Switch to mode_cmd2")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-7-zack@kde.org

drm/vmwgfx: Allow querying of the SVGA PCI id from the userspace

Mesa3D loaders require knowledge of the devices PCI id. SVGAv2 and v3
have different PCI id's, but the same driver is used to handle them both.
To allow Mesa3D svga driver to be loaded automatically for both SVGAv2
and SVGAv3 make the kernel return the PCI id of the currently running
device.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-6-zack@kde.org

drm/vmwgfx: Fix fencing on SVGAv3

Port of the vmwgfx to SVGAv3 lacked support for fencing. SVGAv3 removed
FIFO's and replaced them with command buffers and extra registers.
The initial version of SVGAv3 lacked support for most advanced features
(e.g. 3D) which made fences unnecessary. That is no longer the case,
especially as 3D support is being turned on.

Switch from FIFO commands and capabilities to command buffers and extra
registers to enable fences on SVGAv3.

Fixes: 2cd80dbd3551 ("drm/vmwgfx: Add basic support for SVGA3")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-5-zack@kde.org

drm/vmwgfx: Print capabilities early during the initialization

Capabilities were logged at the end of initialization so any early errors
would make them not appear in the logs. Which is also when they're needed
the most.
Print the the capabilities right after fetching them, before the init
code starts using them to make sure they always show up in the logs.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-4-zack@kde.org

drm/vmwgfx: Cleanup multimon initialization code

The results of the legacy display unit initialization were being silently
ignored. Unifying the selection of number of display units based
on whether the underlying device supports multimon makes it easier
to add error checking to all paths.

This makes the driver report the errors in ldu initialization paths
and try to recover from them.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-3-zack@kde.org

drm/vmwgfx: Add support for CursorMob and CursorBypass 4

* Add support for CursorMob
* Add support for CursorBypass 4
* Refactor vmw_du_cursor_plane_atomic_update to be kms-helper-atomic
-- move BO mappings to vmw_du_cursor_plane_prepare_fb
-- move BO unmappings to vmw_du_cursor_plane_cleanup_fb

Cursor mobs are a new svga feature which enables support for large
cursors, e.g. large accessibility cursor on platforms with vmwgfx. It
also cleans up the cursor code and makes it more uniform with the rest
of modern guest backed objects support.

Signed-off-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-2-zack@kde.org

drm/bridge: analogix_dp: Enable autosuspend

DP AUX transactions can consist of many short operations. There's no
need to power things up/down in short intervals.

I pick an arbitrary 100ms; for the systems I'm testing (Rockchip
RK3399), runtime-PM transitions only take a few microseconds.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220301181107.v4.2.I48b18ab197c9b649d376cf8cfd934e59d338f86d@changeid

drm/bridge: analogix_dp: Grab runtime PM reference for DP-AUX

If the display is not enable()d, then we aren't holding a runtime PM
reference here. Thus, it's easy to accidentally cause a hang, if user
space is poking around at /dev/drm_dp_aux0 at the "wrong" time.

Let's get a runtime PM reference, and check that we "see" the panel.
Don't force any panel power-up, etc., because that can be intrusive, and
that's not what other drivers do (see
drivers/gpu/drm/bridge/ti-sn65dsi86.c and
drivers/gpu/drm/bridge/parade-ps8640.c.)

Fixes: 0d97ad03f422 ("drm/bridge: analogix_dp: Remove duplicated code")
Cc: <stable@vger.kernel.org>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220301181107.v4.1.I773a08785666ebb236917b0c8e6c05e3de471e75@changeid

drm/bridge: Add myself as a reviewer for the Parade PS8640 bridge chip

Though the parade bridge chip is a little bit of a black box, I'm at
least interested in hearing about changes to the driver since this
bridge chip is used on some Chromebooks that I'm involved with.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308110615.3.I04f99fbcc14b8c09610b4b18f0696c992a44d2b7@changeid

drm/bridge: Add myself as a reviewer for the TI SN65DSI86 bridge chip

I've spent quite a bit of time poking at this driver and it's used on
several Chromebooks I'm involved with. I'd like to get notified about
patches. Add myself as a reviewer. It's expected that changes will
still be landed through drm-misc as they always have been.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308110615.2.I4485769d5b25a8096508e839b8fea12ce7b836d3@changeid

drm/bridge: Add MAINTAINERS entry for DRM drivers for bridge chip bindings

The bindings for bridge chips should also get the same maintainers
entry so the right people get notified about bindings changes.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308110615.1.I1f1b10daf7361feb6705f789deb680b8d7720de9@changeid

drm/bridge: anx7625: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221072835.10032-1-jose.exposito89@gmail.com

drm: ssd130x: Always apply segment remap setting

Currently the ssd130x driver only sets the segment remap setting when
the device tree requests it; it however does not clear the setting if
it is not requested. This leads to the setting incorrectly persisting
if the hardware is always on and has no reset GPIO wired. This might
happen when a developer is trying to find the correct settings for an
unknown module, and cause the developer to get confused because the
settings from the device tree are not consistently applied.

Make the driver apply the segment remap setting consistently, setting
the value correctly based on the device tree setting. This also makes
this setting's behavior consistent with the other settings, which are
always applied.

Fixes: a61732e80867 ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308160758.26060-2-wens@kernel.org

drm: ssd130x: Fix COM scan direction register mask

The SSD130x's command to toggle COM scan direction uses bit 3 and only
bit 3 to set the direction of the scanout. The driver has an incorrect
GENMASK(3, 2), causing the setting to be set on bit 2, rendering it
ineffective.

Fix the mask to only bit 3, so that the requested setting is applied
correctly.

Fixes: a61732e80867 ("drm: Add driver for Solomon SSD130x OLED displays")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220308160758.26060-1-wens@kernel.org

drm/bridge: ti-sn65dsi86: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228183955.25508-1-jose.exposito89@gmail.com

drm/bridge: anx7625: check the return on anx7625_aux_trans

Clang static analysis reports this issue
anx7625.c:876:13: warning: The left operand of '&' is
  a garbage value
  if (!(bcap & 0xOA01)) {
        ~~~~ ^

bcap is only set by a successful call to
anx7625_aux_trans().  So check.

Fixes: cd1637c7e480 ("drm/bridge: anx7625: add HDCP support")
Signed-off-by: Tom Rix <trix@redhat.com>
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303201943.501746-1-trix@redhat.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>

drm/bridge: anx7625: config hs packets end aligned to avoid screen shift

This device requires the packets on lanes aligned at the end to fix
screen shift or scroll.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-4-rex-bc.chen@mediatek.com

drm/mediatek: implement the DSI HS packets aligned

Some DSI RX devices (for example, anx7625) require last alignment of
packets on all lanes after each row of data is sent.
Otherwise, there will be some issues of shift or scroll for screen.

Take horizontal_sync_active_byte for a example,
we roundup the HSA packet data to lane number, and the subtraction of 2
is the packet data value added by the roundup operation, making the
long packets are integer multiples of lane number.
This value (2) varies with the lane number, and that is the reason we
do this operation when the lane number is 4.

In the previous operation of function "mtk_dsi_config_vdo_timing",
the length of HSA and HFP data packets has been adjusted to an
integration multiple of lane number.
Since the number of RGB data packets cannot be guaranteed to be an
integer multiple of lane number, we modify the data packet length of
HBP so that the number of HBP + RGB is equal to the lane number.
So after sending a line of data (HSA + HBP + RGB + HFP), the data
lanes are aligned.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-3-rex-bc.chen@mediatek.com

drm/dsi: transfer DSI HS packets ending at the same time

Since a HS transmission is composed of an arbitrary number
of bytes that may not be an integer multiple of lanes, some
lanes may run out of data before others.
(Defined in 6.1.3 of mipi_DSI_specification_v.01-02-00)

However, for some DSI RX devices (for example, anx7625),
there is a limitation that packet number should be the same
on all DSI lanes. In other words, they need to end a HS at
the same time.

Because this limitation is for some specific DSI RX devices,
it is more reasonable to put the enable control in these
DSI RX drivers. If DSI TX driver knows the information,
they can adjust the setting for this situation.

Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-2-rex-bc.chen@mediatek.com

dt-bindings: display: sitronix, st7735r: Remove spi-max-frequency limit

The datasheet lists the minimum Serial clock cycle (Write) as 66ns which is
15MHz. Mostly it can do much better than that and is in fact often run at
32MHz. With a clever driver that runs configuration commands at a low speed
and only the pixel data at the maximum speed the configuration can't be
messed up by transfer errors and the speed is only limited by the amount of
pixel glitches that one is able to tolerate.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124150757.17929-4-noralf@tronnes.org

dt-bindings: display: sitronix, st7735r: Make reset-gpios optional

There are other ways than using a gpio to reset the controller so make
this property optional.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124150757.17929-3-noralf@tronnes.org

dt-bindings: display: sitronix, st7735r: Fix backlight in example

The backlight property was lost during conversion to yaml in commit
abdd9e3705c8 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema").
Put it back.

Fixes: abdd9e3705c8 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema")
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124150757.17929-2-noralf@tronnes.org

drm/doc: pull in drm_buddy.c

Make sure we pull in the kernel-doc for this.

Reported-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220208151228.344997-1-matthew.auld@intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

drm/bridge: ti-sn65dsi83: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228183724.25030-1-jose.exposito89@gmail.com

drm/bridge: tc358775: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228183537.24600-1-jose.exposito89@gmail.com

drm/bridge: tc358762: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228183342.24129-1-jose.exposito89@gmail.com

drm/bridge: parade-ps8640: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228183131.23494-1-jose.exposito89@gmail.com

drm/bridge: parade-ps8622: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228182904.22982-1-jose.exposito89@gmail.com

drm/bridge: nxp-ptn3460: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228182600.22463-1-jose.exposito89@gmail.com

drm/komeda: plane: Remove redundant color encoding and range initialisation

The komeda KMS driver will call drm_plane_create_color_properties() with
a default encoding and range values of BT601 and Limited Range,
respectively.

Since the initial value wasn't carried over in the state, the driver had
to set it again in komeda_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.

Cc: Brian Starkey <brian.starkey@arm.com>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-20-maxime@cerno.tech

drm/komeda: plane: Remove redundant zpos initialisation

The komeda KMS driver will call drm_plane_create_zpos_property() with an
init value of the plane index.

Since the initial value wasn't carried over in the state, the driver had
to set it again in komeda_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.

Cc: Brian Starkey <brian.starkey@arm.com>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-10-maxime@cerno.tech

drm/komeda: plane: switch to plane reset helper

komeda_plane_reset() does the state initialisation by copying a lot of
the code found in the __drm_atomic_helper_plane_reset(). Let's switch to
that helper and reduce the boilerplate.

Cc: Brian Starkey <brian.starkey@arm.com>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-2-maxime@cerno.tech

drm/omap: fix NULL but dereferenced coccicheck error

Fix the following coccicheck warning:
./drivers/gpu/drm/omapdrm/omap_overlay.c:89:22-25: ERROR: r_ovl is NULL
but dereferenced.

Here should be ovl->idx rather than r_ovl->idx.

Fixes: e02b5cc9e898ad ("drm/omap: Add a 'right overlay' to plane state")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307095612.409090-1-wanjiabing@vivo.com

drm/selftests: missing error code in igt_buddy_alloc_smoke()

Set the error code to -ENOMEM if drm_random_order() fails.

Fixes: e6ff5ef81170 ("drm/selftests: add drm buddy smoke testcase")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307125458.GA16710@kili

drm: Drop commas after SoC match table sentinels

It does not make sense to have a comma after a sentinel, as any new
elements must be added before the sentinel.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/298f0644275d7d0b4aa3ee7143756a2431a4900c.1646311443.git.geert+renesas@glider.be

efifb: Remove redundant efifb_setup_from_dmi stub

efifb is the only user of efifb_setup_from_dmi which is provided by
sysfb which is selected by efifb. That makes the stub redundant.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/7416c439d68e9e96068ea5c77e05c99c7df41750.1645822213.git.msuchanek@suse.de

sysfb: Enable boot time VESA graphic mode selection

Since switch to simplefb/simpledrm VESA graphic mode selection with vga=
kernel parameter is no longer available with legacy BIOS.

The x86 realmode boot code enables the VESA graphic modes when option
FB_BOOT_VESA_SUPPORT is enabled.

This option is selected by vesafb but not simplefb/simpledrm.

To enable use of VESA modes with simplefb in legacy BIOS boot mode drop
dependency of BOOT_VESA_SUPPORT on FB, also drop the FB_ prefix. Select
the option from sysfb rather than the drivers that depend on it.

The BOOT_VESA_SUPPORT is not specific to framebuffer but rather to x86
platform, move it from fbdev to x86 Kconfig.

Fixes: e3263ab389a7 ("x86: provide platform-devices for boot-framebuffers")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/948c39940a4e99f5b43bdbcbe537faae71a43e1d.1645822213.git.msuchanek@suse.de

sysfb: Make config option dependencies explicit

efifb and vesafb requires sysfb implicitly but this is not stated in
Kconfig. Add the dependency.

With that all drivers that require sysfb depend on it so it can default
to disabled.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a0fa41e9186653e4c41ad0a28259e5cdc71b1f66.1645822213.git.msuchanek@suse.de

drm/bridge_connector: enable HPD by default if supported

Hotplug events reported by bridge drivers over drm_bridge_hpd_notify()
get ignored unless somebody calls drm_bridge_hpd_enable(). When the
connector for the bridge is bridge_connector, such a call is done from
drm_bridge_connector_enable_hpd().

However drm_bridge_connector_enable_hpd() is never called on init paths,
documentation suggests that it is intended for suspend/resume paths.

In result, once encoders are switched to bridge_connector,
bridge-detected HPD stops working.

This patch adds a call to that API on init path.

This fixes HDMI HPD with rcar-du + adv7513 case when adv7513 reports HPD
events via interrupts.

Fixes: c24110a8fd09 ("drm: rcar-du: Use drm_bridge_connector_init() helper")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211225063151.2110878-1-nikita.yoush@cogentembedded.com

drm/selftests: fix a shift-out-of-bounds bug

pass the correct size value computed using the max_order.

<log snip>

[ 68.124177][ T1] UBSAN: shift-out-of-bounds in include/linux/log2.h:67:13
[ 68.125333][ T1] shift exponent 4294967295 is too large for 32-bit type 'long
unsigned int'
[ 68.126563][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted
5.17.0-rc2-00311-g39ec47bbfd5d #2
[ 68.127758][ T1] Call Trace:
[ 68.128187][ T1] dump_stack_lvl (lib/dump_stack.c:108)
[ 68.128793][ T1] dump_stack (lib/dump_stack.c:114)
[ 68.129331][ T1] ubsan_epilogue (lib/ubsan.c:152)
[ 68.129958][ T1] __ubsan_handle_shift_out_of_bounds.cold (arch/x86/include/asm/smap.h:85)

[ 68.130791][ T1] ? drm_block_alloc+0x28/0x80
[ 68.131582][ T1] ? rcu_read_lock_sched_held (kernel/rcu/update.c:125)
[ 68.132215][ T1] ? kmem_cache_alloc (include/trace/events/kmem.h:54 mm/slab.c:3501)
[ 68.132878][ T1] ? mark_free+0x2e/0x80
[ 68.133524][ T1] drm_buddy_init.cold (include/linux/log2.h:67
drivers/gpu/drm/drm_buddy.c:131)
[ 68.134145][ T1] ? test_drm_cmdline_init (drivers/gpu/drm/selftests/test-drm_buddy.c:87)

[ 68.134770][ T1] igt_buddy_alloc_limit (drivers/gpu/drm/selftests/test-drm_buddy.c:30)
[ 68.135472][ T1] ? vprintk_default (kernel/printk/printk.c:2257)
[ 68.136057][ T1] ? test_drm_cmdline_init (drivers/gpu/drm/selftests/test-drm_buddy.c:87)

[ 68.136812][ T1] test_drm_buddy_init (drivers/gpu/drm/selftests/drm_selftest.c:77
drivers/gpu/drm/selftests/test-drm_buddy.c:95)
[ 68.137475][ T1] do_one_initcall (init/main.c:1300)
[ 68.138111][ T1] ? parse_args (kernel/params.c:609 kernel/params.c:146
kernel/params.c:188)
[ 68.138717][ T1] do_basic_setup (init/main.c:1372 init/main.c:1389 init/main.c:1408)
[ 68.139366][ T1] kernel_init_freeable (init/main.c:1617)
[ 68.140040][ T1] ? rest_init (init/main.c:1494)
[ 68.140634][ T1] kernel_init (init/main.c:1504)
[ 68.141155][ T1] ret_from_fork (arch/x86/entry/entry_32.S:772)
[ 68.141607][ T1]
================================================================================
[ 68.146730][ T1] ------------[ cut here ]------------
[ 68.147460][ T1] kernel BUG at drivers/gpu/drm/drm_buddy.c:140!
[ 68.148280][ T1] invalid opcode: 0000 [#1]
[ 68.148895][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted
5.17.0-rc2-00311-g39ec47bbfd5d #2
[ 68.149896][ T1] EIP: drm_buddy_init (drivers/gpu/drm/drm_buddy.c:140 (discriminator 1))

For more details: https://lists.01.org/hyperkitty/list/lkp@lists.01.org/thread/FDIF3HCILZNN5UQAZMOR7E3MQSMHHKWU/

Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220303201602.2365-1-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/nouveau/instmem: fix uninitialized_var.cocci warning

Fix following coccicheck warning:
drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.c:316:11-12:
WARNING this kind of initialization is deprecated.

`void *map = map` has the same form of
uninitialized_var() macro. I remove the redundant assignement. It has
been tested with gcc (Debian 8.3.0-6) 8.3.0.

The patch which removed uninitialized_var() is:
https://lore.kernel.org/all/20121028102007.GA7547@gmail.com/
And there is very few "/* GCC */" comments in the Linux kernel code now.

Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228142352.18006-1-guozhengkui@vivo.com

drm/ssd130x: remove redundant initialization of pointer mode

Pointer mode is being assigned a value that is never read, it is
being re-assigned later with a new value. The initialization is
redundant and can be removed.

Cleans up clang scan build warning:
drivers/gpu/drm/solomon/ssd130x.c:582:27: warning: Value stored
to 'mode' during its initialization is never read [deadcode.DeadStores]

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302175309.1098827-1-colin.i.king@gmail.com

drm/aspeed: Add AST2600 chip support

Add AST2600 chip support and setting.

Signed-off-by: Tommy Haung <tommy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302024930.18758-5-tommy_huang@aspeedtech.com

drm/aspeed: Update INTR_STS handling

Add interrupt clear register define for further chip support.

Signed-off-by: Tommy Haung <tommy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302024930.18758-4-tommy_huang@aspeedtech.com

drm: Add TODO item for optimizing format helpers

Add a TODO item for optimizing blitting and format-conversion helpers
in DRM and fbdev. There's always demand for faster graphics output.

v4:
* fix typos (Sam)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-6-tzimmermann@suse.de

fbdev: Improve performance of cfb_imageblit()

Improve the performance of cfb_imageblit() by manually unrolling
the inner blitting loop and moving some invariants out. The compiler
failed to do this automatically. This change keeps cfb_imageblit()
in sync with sys_imagebit().

A microbenchmark measures the average number of CPU cycles
for cfb_imageblit() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging).

cfb_imageblit(), new: 15724 cycles
cfb_imageblit(): old: 30566 cycles

In the optimized case, cfb_imageblit() is now ~2x faster than before.

v3:
* fix commit description (Pekka)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-5-tzimmermann@suse.de

fbdev: Remove trailing whitespaces from cfbimgblt.c

Fix coding style. No functional changes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-4-tzimmermann@suse.de

fbdev: Improve performance of sys_imageblit()

Improve the performance of sys_imageblit() by manually unrolling
the inner blitting loop and moving some invariants out. The compiler
failed to do this automatically. The resulting binary code was even
slower than the cfb_imageblit() helper, which uses the same algorithm,
but operates on I/O memory.

A microbenchmark measures the average number of CPU cycles
for sys_imageblit() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging). The value
for CFB is given as a reference.

  sys_imageblit(), new: 25934 cycles
  sys_imageblit(), old: 35944 cycles
  cfb_imageblit():      30566 cycles

In the optimized case, sys_imageblit() is now ~30% faster than before
and ~20% faster than cfb_imageblit().

v2:
* move switch out of inner loop (Gerd)
* remove test for alignment of dst1 (Sam)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-3-tzimmermann@suse.de

fbdev: Improve performance of sys_fillrect()

Improve the performance of sys_fillrect() by using word-aligned
32/64-bit mov instructions. While the code tried to implement this,
the compiler failed to create fast instructions. The resulting
binary instructions were even slower than cfb_fillrect(), which
uses the same algorithm, but operates on I/O memory.

A microbenchmark measures the average number of CPU cycles
for sys_fillrect() after a stabilizing period of a few minutes
(i7-4790, FullHD, simpledrm, kernel with debugging). The value
for CFB is given as a reference.

  sys_fillrect(), new:  26586 cycles
  sys_fillrect(), old: 166603 cycles
  cfb_fillrect():       41012 cycles

In the optimized case, sys_fillrect() is now ~6x faster than before
and ~1.5x faster than the CFB implementation.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223193804.18636-2-tzimmermann@suse.de

drm/panfrost: cleanup comments

For spdx
change tab to space delimiter
Use // for *.c

Replacements
commited to committed
regsiters to registers
initialze to initialize

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302124535.358060-1-trix@redhat.com

drm/bridge: nwl-dsi: Remove superfluous write to NWL_DSI_IRQ_MASK register

To initialize register NWL_DSI_IRQ_MASK, it's enough to write it
only once in function nwl_dsi_init_interrupts().

Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220216085842.1973868-1-victor.liu@nxp.com

drm/bridge: Clear the DP_AUX_I2C_MOT bit passed in aux read command.

If the previous transfer didn't end with a command without DP_AUX_I2C_MOT,
the next read trasnfer will miss the first byte. But if the command in
previous transfer is requested with length 0, it's a no-op to anx7625
since it can't process this command. anx7625 requires the last command
to be read command with length > 0.

It's observed that if we clear the DP_AUX_I2C_MOT in read transfer, we
can still get correct data. Clear the read commands with DP_AUX_I2C_MOT
bit to fix this issue.

Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217082224.1823916-1-hsinyi@chromium.org

drm/v3d: centralize error handling when init scheduler fails

Remove redundant error message (since now it is very similar to what
we do in drm_sched_init) and centralize all error handling in a
unique place, as we follow the same steps in any case of failure.

Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228181647.3794298-1-mwen@igalia.com

drm/bridge: chipone-icn6211: switch to devm_drm_of_get_bridge

The function "drm_of_find_panel_or_bridge" has been deprecated in
favor of "devm_drm_of_get_bridge".

Switch to the new function and reduce boilerplate.

Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221074224.12920-1-jose.exposito89@gmail.com

drm/bridge: anx7625: Fix release wrong workqueue

If "hdcp_workqueue" exist, must release "hdcp_workqueue",
not "workqueue".

Fixes: cd1637c7e480 ("drm/bridge: anx7625: add HDCP support")
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217024418.3780171-1-xji@analogixsemi.com

drm/bridge: it6505: Fix the read buffer array bound

The size of read_buf is READ_BUFFER_SIZE (200), so we can't access it
with read_buf + PAGE_SIZE (4096). Extend the READ_BUFFER_SIZE to 400 and
set the end position to read_buf + READ_BUFFER_SIZE.

Fixes: b5c84a9edcd418 ("drm/bridge: add it6505 driver")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228081421.1504213-1-hsinyi@chromium.org

drm/panel: simple: Initialize bpc in RK101II01D-CT panel descriptor

Initialize bpc while creating panel_desc structure for RK101II01D-CT

Below warning is triggered since bpc is not being initialized

WARNING: CPU: 2 PID: 47 at drivers/gpu/drm/panel/panel-simple.c:614
panel_simple_probe+0x1b0/0x3c8

Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220210140300.11900-1-r-ravikumar@ti.com

drm/bridge: cdns-dsi: Make sure to to create proper aliases for dt

Add MODULE_DEVICE_TABLE to the device tree table to create required
aliases needed for module to be loaded with device tree based platform.

Fixes: e19233955d9e ("drm/bridge: Add Cadence DSI driver")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921174059.17946-1-nm@ti.com

drm/tiny: Add MIPI DBI compatible SPI driver

Add a driver that will work with most MIPI DBI compatible SPI panels.
This avoids adding a driver for every new MIPI DBI compatible controller
that is to be used by Linux. The 'compatible' Device Tree property with
a '.bin' suffix will be used to load a firmware file that contains the
controller configuration.

Example (driver will load sainsmart18.bin):

display@0 {
compatible = "sainsmart18", "panel-mipi-dbi-spi";
...
};

v5:
- kconfig: s/DRM_KMS_CMA_HELPER/DRM_GEM_CMA_HELPER/ (Sam)
- kconfig: Add select VIDEOMODE_HELPERS (Sam)
- kconfig: Add wiki url in the description (Sam)
- Split out and use of_get_drm_panel_display_mode()(Sam)
- Only use the first compatible to look for a firmware file since the
  binding mandates 2 compatibles.
- Make having a firmware file mandatory so we can print an error
  message if it's missing to improve the user experience. It's very
  unlikely that a controller doesn't need to be initialized and if
  it doesn't, it's possible to have a firmware file containing only
  a DCS NOP.

v4:
- Move driver to drm/tiny where the other drivers of its kind are located.
  The driver module will not be shared with a future DPI driver after all.

v3:
- Move properties to DT (Maxime)
- The MIPI DPI spec has optional support for DPI where the controller is
  configured over DBI. Rework the command functions so they can be moved
  to drm_mipi_dbi and shared with a future panel-mipi-dpi-spi driver

v2:
- Drop model property and use compatible instead (Rob)
- Add wiki entry in MAINTAINERS

Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-6-noralf@tronnes.org

drm/mipi-dbi: Add driver_private member to struct mipi_dbi_dev

devm_drm_dev_alloc() can't allocate structures that embed a structure
which then again embeds drm_device. Workaround this by adding a
driver_private pointer to struct mipi_dbi_dev which the driver can use for
its additional state.

v3:
- Add documentation

Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-5-noralf@tronnes.org