platform/kernel/linux-starfive.git
23 months agoserial: amba-pl011: fix high priority character transmission in rs486 mode
Lino Sanfilippo [Sun, 8 Jan 2023 18:17:35 +0000 (19:17 +0100)]
serial: amba-pl011: fix high priority character transmission in rs486 mode

commit 4f39aca2360c82dccd2f5179d77e94aab665bea6 upstream.

In RS485 mode the transmission of a high priority character fails since it
is written to the data register before the transmitter is enabled. Fix this
in pl011_tx_chars() by enabling RS485 transmission before writing the
character.

Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20230108181735.10937-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agodmaengine: idxd: Do not call DMX TX callbacks during workqueue disable
Reinette Chatre [Wed, 7 Dec 2022 22:52:22 +0000 (14:52 -0800)]
dmaengine: idxd: Do not call DMX TX callbacks during workqueue disable

commit 6744a030d81e456883bfbb627ac1f30465c1a989 upstream.

On driver unload any pending descriptors are flushed and pending
DMA descriptors are explicitly completed:
idxd_dmaengine_drv_remove() ->
drv_disable_wq() ->
idxd_wq_free_irq() ->
idxd_flush_pending_descs() ->
idxd_dma_complete_txd()

With this done during driver unload any remaining descriptor is
likely stuck and can be dropped. Even so, the descriptor may still
have a callback set that could no longer be accessible. An
example of such a problem is when the dmatest fails and the dmatest
module is unloaded. The failure of dmatest leaves descriptors with
dma_async_tx_descriptor::callback pointing to code that no longer
exist. This causes a page fault as below at the time the IDXD driver
is unloaded when it attempts to run the callback:
 BUG: unable to handle page fault for address: ffffffffc0665190
 #PF: supervisor instruction fetch in kernel mode
 #PF: error_code(0x0010) - not-present page

Fix this by clearing the callback pointers on the transmit
descriptors only when workqueue is disabled.

Fixes: 403a2e236538 ("dmaengine: idxd: change MSIX allocation based on per wq activation")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/37d06b772aa7f8863ca50f90930ea2fd80b38fc3.1670452419.git.reinette.chatre@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agodmaengine: idxd: Prevent use after free on completion memory
Reinette Chatre [Wed, 7 Dec 2022 22:52:21 +0000 (14:52 -0800)]
dmaengine: idxd: Prevent use after free on completion memory

commit 1beeec45f9ac31eba52478379f70a5fa9c2ad005 upstream.

On driver unload any pending descriptors are flushed at the
time the interrupt is freed:
idxd_dmaengine_drv_remove() ->
drv_disable_wq() ->
idxd_wq_free_irq() ->
idxd_flush_pending_descs().

If there are any descriptors present that need to be flushed this
flow triggers a "not present" page fault as below:

 BUG: unable to handle page fault for address: ff391c97c70c9040
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page

The address that triggers the fault is the address of the
descriptor that was freed moments earlier via:
drv_disable_wq()->idxd_wq_free_resources()

Fix the use after free by freeing the descriptors after any possible
usage. This is done after idxd_wq_reset() to ensure that the memory
remains accessible during possible completion writes by the device.

Fixes: 63c14ae6c161 ("dmaengine: idxd: refactor wq driver enable/disable operations")
Suggested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/6c4657d9cff0a0a00501a7b928297ac966e9ec9d.1670452419.git.reinette.chatre@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agodmaengine: idxd: Let probe fail when workqueue cannot be enabled
Reinette Chatre [Wed, 7 Dec 2022 22:52:20 +0000 (14:52 -0800)]
dmaengine: idxd: Let probe fail when workqueue cannot be enabled

commit b51b75f0604f17c0f6f3b6f68f1a521a5cc6b04f upstream.

The workqueue is enabled when the appropriate driver is loaded and
disabled when the driver is removed. When the driver is removed it
assumes that the workqueue was enabled successfully and proceeds to
free allocations made during workqueue enabling.

Failure during workqueue enabling does not prevent the driver from
being loaded. This is because the error path within drv_enable_wq()
returns success unless a second failure is encountered
during the error path. By returning success it is possible to load
the driver even if the workqueue cannot be enabled and
allocations that do not exist are attempted to be freed during
driver remove.

Some examples of problematic flows:
(a)

 idxd_dmaengine_drv_probe() -> drv_enable_wq() -> idxd_wq_request_irq():
 In above flow, if idxd_wq_request_irq() fails then
 idxd_wq_unmap_portal() is called on error exit path, but
 drv_enable_wq() returns 0 because idxd_wq_disable() succeeds. The
 driver is thus loaded successfully.

 idxd_dmaengine_drv_remove()->drv_disable_wq()->idxd_wq_unmap_portal()
 Above flow on driver unload triggers the WARN in devm_iounmap() because
 the device resource has already been removed during error path of
 drv_enable_wq().

(b)

 idxd_dmaengine_drv_probe() -> drv_enable_wq() -> idxd_wq_request_irq():
 In above flow, if idxd_wq_request_irq() fails then
 idxd_wq_init_percpu_ref() is never called to initialize the percpu
 counter, yet the driver loads successfully because drv_enable_wq()
 returns 0.

 idxd_dmaengine_drv_remove()->__idxd_wq_quiesce()->percpu_ref_kill():
 Above flow on driver unload triggers a BUG when attempting to drop the
 initial ref of the uninitialized percpu ref:
 BUG: kernel NULL pointer dereference, address: 0000000000000010

Fix the drv_enable_wq() error path by returning the original error that
indicates failure of workqueue enabling. This ensures that the probe
fails when an error is encountered and the driver remove paths are only
attempted when the workqueue was enabled successfully.

Fixes: 1f2bb40337f0 ("dmaengine: idxd: move wq_enable() to device.c")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/e8d8116e5efa0fd14fadc5adae6ffd319f0e5ff1.1670452419.git.reinette.chatre@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agodmaengine: tegra210-adma: fix global intr clear
Mohan Kumar [Mon, 2 Jan 2023 06:48:44 +0000 (12:18 +0530)]
dmaengine: tegra210-adma: fix global intr clear

commit 9c7e355ccbb33d239360c876dbe49ad5ade65b47 upstream.

The current global interrupt clear programming register offset
was not correct. Fix the programming with right offset

Fixes: ded1f3db4cd6 ("dmaengine: tegra210-adma: prepare for supporting newer Tegra chips")
Cc: stable@vger.kernel.org
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20230102064844.31306-1-mkumard@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agodmaengine: lgm: Move DT parsing after initialization
Peter Harliman Liem [Thu, 5 Jan 2023 03:05:51 +0000 (11:05 +0800)]
dmaengine: lgm: Move DT parsing after initialization

commit 96b3bb18f6cbe259ef4e0bed3135911b7e8d2af5 upstream.

ldma_cfg_init() will parse DT to retrieve certain configs.
However, that is called before ldma_dma_init_vXX(), which
will make some initialization to channel configs. It will
thus incorrectly overwrite certain configs that are declared
in DT.

To fix that, we move DT parsing after initialization.
Function name is renamed to better represent what it does.

Fixes: 32d31c79a1a4 ("dmaengine: Add Intel LGM SoC DMA support.")
Signed-off-by: Peter Harliman Liem <pliem@maxlinear.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/afef6fc1ed20098b684e0d53737d69faf63c125f.1672887183.git.pliem@maxlinear.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoserial: pch_uart: Pass correct sg to dma_unmap_sg()
Ilpo Järvinen [Tue, 3 Jan 2023 09:34:35 +0000 (11:34 +0200)]
serial: pch_uart: Pass correct sg to dma_unmap_sg()

commit e8914b52e5b024e4af3d810a935fe0805eee8a36 upstream.

A local variable sg is used to store scatterlist pointer in
pch_dma_tx_complete(). The for loop doing Tx byte accounting before
dma_unmap_sg() alters sg in its increment statement. Therefore, the
pointer passed into dma_unmap_sg() won't match to the one given to
dma_map_sg().

To fix the problem, use priv->sg_tx_p directly in dma_unmap_sg()
instead of the local variable.

Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230103093435.4396-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agodt-bindings: phy: g12a-usb3-pcie-phy: fix compatible string documentation
Heiner Kallweit [Mon, 16 Jan 2023 20:19:03 +0000 (21:19 +0100)]
dt-bindings: phy: g12a-usb3-pcie-phy: fix compatible string documentation

commit e181119046a0ec16126b682163040e8e33f310c1 upstream.

The compatible string in the driver doesn't have the meson prefix.
Fix this in the documentation and rename the file accordingly.

Fixes: 87a55485f2fc ("dt-bindings: phy: meson-g12a-usb3-pcie-phy: convert to yaml")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/0a82be92-ce85-da34-9d6f-4b33034473e5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agodt-bindings: phy: g12a-usb2-phy: fix compatible string documentation
Heiner Kallweit [Mon, 16 Jan 2023 20:17:39 +0000 (21:17 +0100)]
dt-bindings: phy: g12a-usb2-phy: fix compatible string documentation

commit c63835bf1c750c9b3aec1d5c23d811d6375fc23d upstream.

The compatible strings in the driver don't have the meson prefix.
Fix this in the documentation and rename the file accordingly.

Fixes: da86d286cce8 ("dt-bindings: phy: meson-g12a-usb2-phy: convert to yaml")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/8d960029-e94d-224b-911f-03e5deb47ebc@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoarm64: dts: imx8mp: correct usb clocks
Li Jun [Fri, 30 Sep 2022 14:54:23 +0000 (22:54 +0800)]
arm64: dts: imx8mp: correct usb clocks

commit 8a1ed98fe0f2e7669f0409de0f46f317b275f8be upstream.

After commit cf7f3f4fa9e5 ("clk: imx8mp: fix usb_root_clk parent"),
usb_root_clk is no longer for suspend clock so update dts accordingly
to use right bus clock and suspend clock.

Fixes: fb8587a2c165 ("arm64: dtsi: imx8mp: add usb nodes")
Cc: stable@vger.kernel.org # ed1f4ccfe947: clk: imx: imx8mp: add shared clk gate for usb suspend clk
Cc: stable@vger.kernel.org # v5.19+
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb-storage: apply IGNORE_UAS only for HIKSEMI MD202 on RTL9210
Juhyung Park [Tue, 17 Jan 2023 08:51:54 +0000 (17:51 +0900)]
usb-storage: apply IGNORE_UAS only for HIKSEMI MD202 on RTL9210

commit dbd24ec17b85b45f4e823d1aa5607721920f2b05 upstream.

The commit e00b488e813f ("usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS")
blacklists UAS for all of RTL9210 enclosures.

The RTL9210 controller was advertised with UAS since its release back in
2019 and was shipped with a lot of enclosure products with different
firmware combinations.

Blacklist UAS only for HIKSEMI MD202.

This should hopefully be replaced with more robust method than just
comparing strings.  But with limited information [1] provided thus far
(dmesg when the device is plugged in, which includes manufacturer and
product, but no lsusb -v to compare against), this is the best we can do
for now.

[1] https://lore.kernel.org/all/20230109115550.71688-1-qkrwngud825@gmail.com

Fixes: e00b488e813f ("usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS")
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Hongling Zeng <zenghongling@kylinos.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Juhyung Park <qkrwngud825@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20230117085154.123301-1-qkrwngud825@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: gadget: f_ncm: fix potential NULL ptr deref in ncm_bitrate()
Maciej Żenczykowski [Tue, 17 Jan 2023 13:18:39 +0000 (05:18 -0800)]
usb: gadget: f_ncm: fix potential NULL ptr deref in ncm_bitrate()

commit c6ec929595c7443250b2a4faea988c62019d5cd2 upstream.

In Google internal bug 265639009 we've received an (as yet) unreproducible
crash report from an aarch64 GKI 5.10.149-android13 running device.

AFAICT the source code is at:
  https://android.googlesource.com/kernel/common/+/refs/tags/ASB-2022-12-05_13-5.10

The call stack is:
  ncm_close() -> ncm_notify() -> ncm_do_notify()
with the crash at:
  ncm_do_notify+0x98/0x270
Code: 79000d0b b9000a6c f940012a f9400269 (b9405d4b)

Which I believe disassembles to (I don't know ARM assembly, but it looks sane enough to me...):

  // halfword (16-bit) store presumably to event->wLength (at offset 6 of struct usb_cdc_notification)
  0B 0D 00 79    strh w11, [x8, #6]

  // word (32-bit) store presumably to req->Length (at offset 8 of struct usb_request)
  6C 0A 00 B9    str  w12, [x19, #8]

  // x10 (NULL) was read here from offset 0 of valid pointer x9
  // IMHO we're reading 'cdev->gadget' and getting NULL
  // gadget is indeed at offset 0 of struct usb_composite_dev
  2A 01 40 F9    ldr  x10, [x9]

  // loading req->buf pointer, which is at offset 0 of struct usb_request
  69 02 40 F9    ldr  x9, [x19]

  // x10 is null, crash, appears to be attempt to read cdev->gadget->max_speed
  4B 5D 40 B9    ldr  w11, [x10, #0x5c]

which seems to line up with ncm_do_notify() case NCM_NOTIFY_SPEED code fragment:

  event->wLength = cpu_to_le16(8);
  req->length = NCM_STATUS_BYTECOUNT;

  /* SPEED_CHANGE data is up/down speeds in bits/sec */
  data = req->buf + sizeof *event;
  data[0] = cpu_to_le32(ncm_bitrate(cdev->gadget));

My analysis of registers and NULL ptr deref crash offset
  (Unable to handle kernel NULL pointer dereference at virtual address 000000000000005c)
heavily suggests that the crash is due to 'cdev->gadget' being NULL when executing:
  data[0] = cpu_to_le32(ncm_bitrate(cdev->gadget));
which calls:
  ncm_bitrate(NULL)
which then calls:
  gadget_is_superspeed(NULL)
which reads
  ((struct usb_gadget *)NULL)->max_speed
and hits a panic.

AFAICT, if I'm counting right, the offset of max_speed is indeed 0x5C.
(remember there's a GKI KABI reservation of 16 bytes in struct work_struct)

It's not at all clear to me how this is all supposed to work...
but returning 0 seems much better than panic-ing...

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Carlos Llamas <cmllamas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230117131839.1138208-1-maze@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: gadget: Add ID numbers to configfs-gadget driver names
Chanh Nguyen [Wed, 11 Jan 2023 06:51:05 +0000 (13:51 +0700)]
USB: gadget: Add ID numbers to configfs-gadget driver names

commit 7c07553807c5125c89de242d35c10c206fd8e6bb upstream.

It is unable to use configfs to attach more than one gadget. When
attaching the second gadget, it always fails and the kernel message
prints out:

Error: Driver 'configfs-gadget' is already registered, aborting...
UDC core: g1: driver registration failed: -16

This commit fixes the problem by using the gadget name as a suffix
to each configfs_gadget's driver name, thus making the names
distinct.

Fixes: fc274c1e9973 ("USB: gadget: Add a new bus for gadgets")
Cc: stable <stable@kernel.org>
Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Link: https://lore.kernel.org/r/20230111065105.29205-1-chanh@os.amperecomputing.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: gadget: g_webcam: Send color matching descriptor per frame
Daniel Scally [Fri, 16 Dec 2022 16:05:28 +0000 (16:05 +0000)]
usb: gadget: g_webcam: Send color matching descriptor per frame

commit e95765e97d9cb93258a4840440d410fa6ff7e819 upstream.

Currently the color matching descriptor is only sent across the wire
a single time, following the descriptors for each format and frame.
According to the UVC 1.5 Specification 3.9.2.6 ("Color Matching
Descriptors"):

"Only one instance is allowed for a given format and if present,
the Color Matching descriptor shall be placed following the Video
and Still Image Frame descriptors for that format".

Add another reference to the color matching descriptor after the
yuyv frames so that it's correctly transmitted for that format
too.

Fixes: a9914127e834 ("USB gadget: Webcam device")
Cc: stable <stable@kernel.org>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20221216160528.479094-1-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: typec: altmodes/displayport: Fix pin assignment calculation
Prashant Malani [Wed, 11 Jan 2023 02:05:42 +0000 (02:05 +0000)]
usb: typec: altmodes/displayport: Fix pin assignment calculation

commit 9682b41e52cc9f42f5c33caf410464392adaef04 upstream.

Commit c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin
assignment for UFP receptacles") fixed the pin assignment calculation
to take into account whether the peripheral was a plug or a receptacle.

But the "pin_assignments" sysfs logic was not updated. Address this by
using the macros introduced in the aforementioned commit in the sysfs
logic too.

Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111020546.3384569-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: typec: altmodes/displayport: Add pin assignment helper
Prashant Malani [Wed, 11 Jan 2023 02:05:41 +0000 (02:05 +0000)]
usb: typec: altmodes/displayport: Add pin assignment helper

commit 582836e3cfab4faafbdc93bbec96fce036a08ee1 upstream.

The code to extract a peripheral's currently supported Pin Assignments
is repeated in a couple of locations. Factor it out into a separate
function.

This will also make it easier to add fixes (we only need to update 1
location instead of 2).

Fixes: c1e5c2f0cb8a ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230111020546.3384569-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: typec: tcpm: Fix altmode re-registration causes sysfs create fail
ChiYuan Huang [Mon, 9 Jan 2023 07:19:50 +0000 (15:19 +0800)]
usb: typec: tcpm: Fix altmode re-registration causes sysfs create fail

commit 36f78477ac2c89e9a2eed4a31404a291a3450b5d upstream.

There's the altmode re-registeration issue after data role
swap (DR_SWAP).

Comparing to USBPD 2.0, in USBPD 3.0, it loose the limit that only DFP
can initiate the VDM command to get partner identity information.

For a USBPD 3.0 UFP device, it may already get the identity information
from its port partner before DR_SWAP. If DR_SWAP send or receive at the
mean time, 'send_discover' flag will be raised again. It causes discover
identify action restart while entering ready state. And after all
discover actions are done, the 'tcpm_register_altmodes' will be called.
If old altmode is not unregistered, this sysfs create fail can be found.

In 'DR_SWAP_CHANGE_DR' state case, only DFP will unregister altmodes.
For UFP, the original altmodes keep registered.

This patch fix the logic that after DR_SWAP, 'tcpm_unregister_altmodes'
must be called whatever the current data role is.

Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Fixes: ae8a2ca8a221 ("usb: typec: Group all TCPCI/TCPM code together")
Reported-by: TommyYl Chen <tommyyl.chen@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1673248790-15794-1-git-send-email-cy_huang@richtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: musb: fix error return code in omap2430_probe()
Yang Yingliang [Fri, 30 Dec 2022 08:17:30 +0000 (16:17 +0800)]
usb: musb: fix error return code in omap2430_probe()

commit bd449ad8cee9d4b523abbdfa73e1a2a08333f331 upstream.

Before calling platform_get_resource() in omap2430_probe(), the 'ret' is
re-assgined to 0, it can't return an error code, if platform_get_resource
fails. Set the error code to -EINVAL to fix this.

Fixes: ffbe2feac59b ("usb: musb: omap2430: Fix probe regression for missing resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221230081730.1655616-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: host: ehci-fsl: Fix module alias
Alexander Stein [Fri, 20 Jan 2023 12:27:14 +0000 (13:27 +0100)]
usb: host: ehci-fsl: Fix module alias

commit 5d3d01ae15d2f37ed0325c99ab47ef0ae5d05f3c upstream.

Commit ca07e1c1e4a6 ("drivers:usb:fsl:Make fsl ehci drv an independent
driver module") changed DRV_NAME which was used for MODULE_ALIAS as well.
Starting from this the module alias didn't match the platform device
name created in fsl-mph-dr-of.c
Change DRV_NAME to match the driver name for host mode in fsl-mph-dr-of.
This is needed for module autoloading on ls1021a.

Fixes: ca07e1c1e4a6 ("drivers:usb:fsl:Make fsl ehci drv an independent driver module")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230120122714.3848784-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: cdns3: remove fetched trb from cache before dequeuing
Pawel Laszczak [Tue, 15 Nov 2022 10:00:39 +0000 (05:00 -0500)]
usb: cdns3: remove fetched trb from cache before dequeuing

commit 1301c7b9f7efad2f11ef924e317c18ebd714fc9a upstream.

After doorbell DMA fetches the TRB. If during dequeuing request
driver changes NORMAL TRB to LINK TRB but doesn't delete it from
controller cache then controller will handle cached TRB and packet
can be lost.

The example scenario for this issue looks like:
1. queue request - set doorbell
2. dequeue request
3. send OUT data packet from host
4. Device will accept this packet which is unexpected
5. queue new request - set doorbell
6. Device lost the expected packet.

By setting DFLUSH controller clears DRDY bit and stop DMA transfer.

Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20221115100039.441295-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: serial: cp210x: add SCALANCE LPE-9000 device id
Michael Adler [Tue, 3 Jan 2023 13:48:50 +0000 (14:48 +0100)]
USB: serial: cp210x: add SCALANCE LPE-9000 device id

commit 3f9e76e31704a325170e5aec2243c8d084d74854 upstream.

Add the USB serial console device ID for Siemens SCALANCE LPE-9000
which have a USB port for their serial console.

Signed-off-by: Michael Adler <michael.adler@siemens.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: gadgetfs: Fix race between mounting and unmounting
Alan Stern [Fri, 23 Dec 2022 14:59:09 +0000 (09:59 -0500)]
USB: gadgetfs: Fix race between mounting and unmounting

commit d18dcfe9860e842f394e37ba01ca9440ab2178f4 upstream.

The syzbot fuzzer and Gerald Lee have identified a use-after-free bug
in the gadgetfs driver, involving processes concurrently mounting and
unmounting the gadgetfs filesystem.  In particular, gadgetfs_fill_super()
can race with gadgetfs_kill_sb(), causing the latter to deallocate
the_device while the former is using it.  The output from KASAN says,
in part:

BUG: KASAN: use-after-free in instrument_atomic_read_write include/linux/instrumented.h:102 [inline]
BUG: KASAN: use-after-free in atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
BUG: KASAN: use-after-free in __refcount_sub_and_test include/linux/refcount.h:272 [inline]
BUG: KASAN: use-after-free in __refcount_dec_and_test include/linux/refcount.h:315 [inline]
BUG: KASAN: use-after-free in refcount_dec_and_test include/linux/refcount.h:333 [inline]
BUG: KASAN: use-after-free in put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
BUG: KASAN: use-after-free in gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
Write of size 4 at addr ffff8880276d7840 by task syz-executor126/18689

CPU: 0 PID: 18689 Comm: syz-executor126 Not tainted 6.1.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
 <TASK>
...
 atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
 __refcount_sub_and_test include/linux/refcount.h:272 [inline]
 __refcount_dec_and_test include/linux/refcount.h:315 [inline]
 refcount_dec_and_test include/linux/refcount.h:333 [inline]
 put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
 gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
 deactivate_locked_super+0xa7/0xf0 fs/super.c:332
 vfs_get_super fs/super.c:1190 [inline]
 get_tree_single+0xd0/0x160 fs/super.c:1207
 vfs_get_tree+0x88/0x270 fs/super.c:1531
 vfs_fsconfig_locked fs/fsopen.c:232 [inline]

The simplest solution is to ensure that gadgetfs_fill_super() and
gadgetfs_kill_sb() are serialized by making them both acquire a new
mutex.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+33d7ad66d65044b93f16@syzkaller.appspotmail.com
Reported-and-tested-by: Gerald Lee <sundaywind2004@gmail.com>
Link: https://lore.kernel.org/linux-usb/CAO3qeMVzXDP-JU6v1u5Ags6Q-bb35kg3=C6d04DjzA9ffa5x1g@mail.gmail.com/
Fixes: e5d82a7360d1 ("vfs: Convert gadgetfs to use the new mount API")
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Y6XCPXBpn3tmjdCC@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoselftests: mptcp: userspace: validate v4-v6 subflows mix
Matthieu Baerts [Thu, 12 Jan 2023 17:42:53 +0000 (18:42 +0100)]
selftests: mptcp: userspace: validate v4-v6 subflows mix

commit 4656d72c1efa495a58ad6d8b073a60907073e4e6 upstream.

MPTCP protocol supports having subflows in both IPv4 and IPv6. In Linux,
it is possible to have that if the MPTCP socket has been created with
AF_INET6 family without the IPV6_V6ONLY option.

Here, a new IPv4 subflow is being added to the initial IPv6 connection,
then being removed using Netlink commands.

Cc: stable@vger.kernel.org # v5.19+
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomptcp: netlink: respect v4/v6-only sockets
Matthieu Baerts [Thu, 12 Jan 2023 17:42:52 +0000 (18:42 +0100)]
mptcp: netlink: respect v4/v6-only sockets

commit fb00ee4f3343acb2b9222ca9b73b47dd1e1a8efc upstream.

If an MPTCP socket has been created with AF_INET6 and the IPV6_V6ONLY
option has been set, the userspace PM would allow creating subflows
using IPv4 addresses, e.g. mapped in v6.

The kernel side of userspace PM will also accept creating subflows with
local and remote addresses having different families. Depending on the
subflow socket's family, different behaviours are expected:
 - If AF_INET is forced with a v6 address, the kernel will take the last
   byte of the IP and try to connect to that: a new subflow is created
   but to a non expected address.
 - If AF_INET6 is forced with a v4 address, the kernel will try to
   connect to a v4 address (v4-mapped-v6). A -EBADF error from the
   connect() part is then expected.

It is then required to check the given families can be accepted. This is
done by using a new helper for addresses family matching, taking care of
IPv4 vs IPv4-mapped-IPv6 addresses. This helper will be re-used later by
the in-kernel path-manager to use mixed IPv4 and IPv6 addresses.

While at it, a clear error message is now reported if there are some
conflicts with the families that have been passed by the userspace.

Fixes: 702c2f646d42 ("mptcp: netlink: allow userspace-driven subflow establishment")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomptcp: explicitly specify sock family at subflow creation time
Paolo Abeni [Thu, 12 Jan 2023 17:42:51 +0000 (18:42 +0100)]
mptcp: explicitly specify sock family at subflow creation time

commit 6bc1fe7dd748ba5e76e7917d110837cafe7b931c upstream.

Let the caller specify the to-be-created subflow family.

For a given MPTCP socket created with the AF_INET6 family, the current
userspace PM can already ask the kernel to create subflows in v4 and v6.
If "plain" IPv4 addresses are passed to the kernel, they are
automatically mapped in v6 addresses "by accident". This can be
problematic because the userspace will need to pass different addresses,
now the v4-mapped-v6 addresses to destroy this new subflow.

On the other hand, if the MPTCP socket has been created with the AF_INET
family, the command to create a subflow in v6 will be accepted but the
result will not be the one as expected as new subflow will be created in
IPv4 using part of the v6 addresses passed to the kernel: not creating
the expected subflow then.

No functional change intended for the in-kernel PM where an explicit
enforcement is currently in place. This arbitrary enforcement will be
leveraged by other patches in a future version.

Fixes: 702c2f646d42 ("mptcp: netlink: allow userspace-driven subflow establishment")
Cc: stable@vger.kernel.org
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoio_uring/poll: don't reissue in case of poll race on multishot request
Jens Axboe [Fri, 20 Jan 2023 22:08:21 +0000 (15:08 -0700)]
io_uring/poll: don't reissue in case of poll race on multishot request

commit 8caa03f10bf92cb8657408a6ece6a8a73f96ce13 upstream.

A previous commit fixed a poll race that can occur, but it's only
applicable for multishot requests. For a multishot request, we can safely
ignore a spurious wakeup, as we never leave the waitqueue to begin with.

A blunt reissue of a multishot armed request can cause us to leak a
buffer, if they are ring provided. While this seems like a bug in itself,
it's not really defined behavior to reissue a multishot request directly.
It's less efficient to do so as well, and not required to rearm anything
like it is for singleshot poll requests.

Cc: stable@vger.kernel.org
Fixes: 6e5aedb9324a ("io_uring/poll: attempt request issue after racy poll wakeup")
Reported-and-tested-by: Olivier Langlois <olivier@trillion01.com>
Link: https://github.com/axboe/liburing/issues/778
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agopktcdvd: check for NULL returna fter calling bio_split_to_limits()
Jens Axboe [Mon, 16 Jan 2023 15:51:05 +0000 (08:51 -0700)]
pktcdvd: check for NULL returna fter calling bio_split_to_limits()

commit 3e9900f3bd7ba30d60f82b162b70a1dffe4e8e24 upstream.

The revert of the removal of this driver happened after we fixed up
the split limits for NOWAIT issue, hence it got missed. Ensure that
we check for a NULL bio after splitting, in case it should be retried.

Marking this as fixing both commits, so that stable backport will do
this correctly.

Cc: stable@vger.kernel.org
Fixes: 9cea62b2cbab ("block: don't allow splitting of a REQ_NOWAIT bio")
Fixes: 4b83e99ee709 ("Revert "pktcdvd: remove driver."")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agotty: fix possible null-ptr-defer in spk_ttyio_release
Gaosheng Cui [Fri, 2 Dec 2022 06:06:33 +0000 (14:06 +0800)]
tty: fix possible null-ptr-defer in spk_ttyio_release

commit 5abbeebd8296c2301023b8dc4b5a6c0d5229b4f5 upstream.

Run the following tests on the qemu platform:

syzkaller:~# modprobe speakup_audptr
 input: Speakup as /devices/virtual/input/input4
 initialized device: /dev/synth, node (MAJOR 10, MINOR 125)
 speakup 3.1.6: initialized
 synth name on entry is: (null)
 synth probe

spk_ttyio_initialise_ldisc failed because tty_kopen_exclusive returned
failed (errno -16), then remove the module, we will get a null-ptr-defer
problem, as follow:

syzkaller:~# modprobe -r speakup_audptr
 releasing synth audptr
 BUG: kernel NULL pointer dereference, address: 0000000000000080
 #PF: supervisor write access in kernel mode
 #PF: error_code(0x0002) - not-present page
 PGD 0 P4D 0
 Oops: 0002 [#1] PREEMPT SMP PTI
 CPU: 2 PID: 204 Comm: modprobe Not tainted 6.1.0-rc6-dirty #1
 RIP: 0010:mutex_lock+0x14/0x30
 Call Trace:
 <TASK>
  spk_ttyio_release+0x19/0x70 [speakup]
  synth_release.part.6+0xac/0xc0 [speakup]
  synth_remove+0x56/0x60 [speakup]
  __x64_sys_delete_module+0x156/0x250
  ? fpregs_assert_state_consistent+0x1d/0x50
  do_syscall_64+0x37/0x90
  entry_SYSCALL_64_after_hwframe+0x63/0xcd
 </TASK>
 Modules linked in: speakup_audptr(-) speakup
 Dumping ftrace buffer:

in_synth->dev was not initialized during modprobe, so we add check
for in_synth->dev to fix this bug.

Fixes: 4f2a81f3a882 ("speakup: Reference synth from tty and tty from synth")
Cc: stable <stable@kernel.org>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221202060633.217364-1-cuigaosheng1@huawei.com
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agotty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
Krzysztof Kozlowski [Wed, 21 Dec 2022 16:40:22 +0000 (17:40 +0100)]
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer

commit b8caf69a6946e18ffebad49847e258f5b6d52ac2 upstream.

Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16.  Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.

The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds.  This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:

  Bluetooth: hci0: QCA Product ID   :0x00000010
  Bluetooth: hci0: QCA SOC Version  :0x400a0200
  Bluetooth: hci0: QCA ROM Version  :0x00000200
  Bluetooth: hci0: QCA Patch Version:0x00000d2b
  Bluetooth: hci0: QCA controller version 0x02000200
  Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
  bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
  Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
  Bluetooth: hci0: QCA Failed to download patch (-2)
  ==================================================================
  BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
  Write of size 4 at addr ffff279347d578c0 by task swapper/0/0

  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26
  Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
  Call trace:
   dump_backtrace.part.0+0xe0/0xf0
   show_stack+0x18/0x40
   dump_stack_lvl+0x8c/0xb8
   print_report+0x188/0x488
   kasan_report+0xb4/0x100
   __asan_store4+0x80/0xa4
   handle_rx_uart+0xa8/0x18c
   qcom_geni_serial_handle_rx+0x84/0x9c
   qcom_geni_serial_isr+0x24c/0x760
   __handle_irq_event_percpu+0x108/0x500
   handle_irq_event+0x6c/0x110
   handle_fasteoi_irq+0x138/0x2cc
   generic_handle_domain_irq+0x48/0x64

If the RX FIFO depth changes after probe, be sure to resize the buffer.

Fixes: f9d690b6ece7 ("tty: serial: qcom_geni_serial: Allocate port->rx_fifo buffer in probe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221221164022.1087814-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobpf: restore the ebpf program ID for BPF_AUDIT_UNLOAD and PERF_BPF_EVENT_PROG_UNLOAD
Paul Moore [Fri, 6 Jan 2023 15:43:59 +0000 (10:43 -0500)]
bpf: restore the ebpf program ID for BPF_AUDIT_UNLOAD and PERF_BPF_EVENT_PROG_UNLOAD

commit ef01f4e25c1760920e2c94f1c232350277ace69b upstream.

When changing the ebpf program put() routines to support being called
from within IRQ context the program ID was reset to zero prior to
calling the perf event and audit UNLOAD record generators, which
resulted in problems as the ebpf program ID was bogus (always zero).
This patch addresses this problem by removing an unnecessary call to
bpf_prog_free_id() in __bpf_prog_offload_destroy() and adjusting
__bpf_prog_put() to only call bpf_prog_free_id() after audit and perf
have finished their bpf program unload tasks in
bpf_prog_put_deferred().  For the record, no one can determine, or
remember, why it was necessary to free the program ID, and remove it
from the IDR, prior to executing bpf_prog_put_deferred();
regardless, both Stanislav and Alexei agree that the approach in this
patch should be safe.

It is worth noting that when moving the bpf_prog_free_id() call, the
do_idr_lock parameter was forced to true as the ebpf devs determined
this was the correct as the do_idr_lock should always be true.  The
do_idr_lock parameter will be removed in a follow-up patch, but it
was kept here to keep the patch small in an effort to ease any stable
backports.

I also modified the bpf_audit_prog() logic used to associate the
AUDIT_BPF record with other associated records, e.g. @ctx != NULL.
Instead of keying off the operation, it now keys off the execution
context, e.g. '!in_irg && !irqs_disabled()', which is much more
appropriate and should help better connect the UNLOAD operations with
the associated audit state (other audit records).

Cc: stable@vger.kernel.org
Fixes: d809e134be7a ("bpf: Prepare bpf_prog_put() to be called from irq context.")
Reported-by: Burn Alting <burn.alting@iinet.net.au>
Reported-by: Jiri Olsa <olsajiri@gmail.com>
Suggested-by: Stanislav Fomichev <sdf@google.com>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20230106154400.74211-1-paul@paul-moore.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoriscv: dts: sifive: fu740: fix size of pcie 32bit memory
Ben Dooks [Fri, 6 Jan 2023 13:44:56 +0000 (13:44 +0000)]
riscv: dts: sifive: fu740: fix size of pcie 32bit memory

commit 43d5f5d63699724d47f0d9e0eae516a260d232b4 upstream.

The 32-bit memory resource is needed for non-prefetchable memory
allocations on the PCIe bus, however with some cards (such as the
SM768) the system fails to allocate memory from this.

Checking the allocation against the datasheet, it looks like there
has been a mis-calcualation of the resource for the first memory
region (0x0060090000..0x0070ffffff) which in the data-sheet for
the fu740 (v1p2) is from 0x0060000000..0x007fffffff. Changing
this to allocate from 0x0060090000..0x007fffffff fixes the probing
issues.

Fixes: ae80d5148085 ("riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC")
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: stable@vger.kernel.org
Tested-by: Ron Economos <re@w6rz.net> # from IRC
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agothunderbolt: Do not call PM runtime functions in tb_retimer_scan()
Mika Westerberg [Thu, 29 Dec 2022 12:10:30 +0000 (14:10 +0200)]
thunderbolt: Do not call PM runtime functions in tb_retimer_scan()

commit 23257cfc1cb7202fd0065e9f4a6a0aac1c04c4a9 upstream.

We cannot call PM runtime functions in tb_retimer_scan() because it will
also be called when retimers are scanned from userspace (happens when
there is no device connected on ChromeOS for instance) and at the same
USB4 port runtime resume hook. This leads to hang because neither can
proceed.

Fix this by runtime resuming USB4 ports in tb_scan_port() instead. This
makes sure the ports are runtime PM active when retimers are added under
it while avoiding the reported hang as well.

Reported-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Fixes: 1e56c88adecc ("thunderbolt: Runtime resume USB4 port when retimers are scanned")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agothunderbolt: Do not report errors if on-board retimers are found
Utkarsh Patel [Fri, 23 Dec 2022 04:22:46 +0000 (20:22 -0800)]
thunderbolt: Do not report errors if on-board retimers are found

commit c28f3d80383571d3630df1a0e89500d23e855924 upstream.

Currently we return an error even if on-board retimers are found and
that's not expected. Fix this to return an error only if there was one
and 0 otherwise.

Fixes: 1e56c88adecc ("thunderbolt: Runtime resume USB4 port when retimers are scanned")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agothunderbolt: Use correct function to calculate maximum USB3 link rate
Mika Westerberg [Fri, 20 May 2022 10:35:19 +0000 (13:35 +0300)]
thunderbolt: Use correct function to calculate maximum USB3 link rate

commit e8ff07fb33026c5c1bb5b81293496faba5d68059 upstream.

We need to take minimum of both sides of the USB3 link into consideration,
not just the downstream port. Fix this by calling tb_usb3_max_link_rate()
instead.

Fixes: 0bd680cd900c ("thunderbolt: Add USB3 bandwidth management")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agothunderbolt: Disable XDomain lane 1 only in software connection manager
Mika Westerberg [Thu, 8 Sep 2022 06:45:22 +0000 (09:45 +0300)]
thunderbolt: Disable XDomain lane 1 only in software connection manager

commit 84ee211c83212f4d35b56e0603acdcc41f860f1b upstream.

When firmware connection manager is in use we should not touch the lane
adapter (well or any) configuration space so do this only when we know
that the software connection manager is active.

Fixes: 8e1de7042596 ("thunderbolt: Add support for XDomain lane bonding")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agocifs: do not include page data when checking signature
Enzo Matsumiya [Wed, 18 Jan 2023 17:06:57 +0000 (14:06 -0300)]
cifs: do not include page data when checking signature

commit 30b2b2196d6e4cc24cbec633535a2404f258ce69 upstream.

On async reads, page data is allocated before sending.  When the
response is received but it has no data to fill (e.g.
STATUS_END_OF_FILE), __calc_signature() will still include the pages in
its computation, leading to an invalid signature check.

This patch fixes this by not setting the async read smb_rqst page data
(zeroed by default) if its got_bytes is 0.

This can be reproduced/verified with xfstests generic/465.

Cc: <stable@vger.kernel.org>
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: fix race between quota rescan and disable leading to NULL pointer deref
Filipe Manana [Thu, 12 Jan 2023 16:31:08 +0000 (16:31 +0000)]
btrfs: fix race between quota rescan and disable leading to NULL pointer deref

commit b7adbf9ada3513d2092362c8eac5cddc5b651f5c upstream.

If we have one task trying to start the quota rescan worker while another
one is trying to disable quotas, we can end up hitting a race that results
in the quota rescan worker doing a NULL pointer dereference. The steps for
this are the following:

1) Quotas are enabled;

2) Task A calls the quota rescan ioctl and enters btrfs_qgroup_rescan().
   It calls qgroup_rescan_init() which returns 0 (success) and then joins a
   transaction and commits it;

3) Task B calls the quota disable ioctl and enters btrfs_quota_disable().
   It clears the bit BTRFS_FS_QUOTA_ENABLED from fs_info->flags and calls
   btrfs_qgroup_wait_for_completion(), which returns immediately since the
   rescan worker is not yet running.
   Then it starts a transaction and locks fs_info->qgroup_ioctl_lock;

4) Task A queues the rescan worker, by calling btrfs_queue_work();

5) The rescan worker starts, and calls rescan_should_stop() at the start
   of its while loop, which results in 0 iterations of the loop, since
   the flag BTRFS_FS_QUOTA_ENABLED was cleared from fs_info->flags by
   task B at step 3);

6) Task B sets fs_info->quota_root to NULL;

7) The rescan worker tries to start a transaction and uses
   fs_info->quota_root as the root argument for btrfs_start_transaction().
   This results in a NULL pointer dereference down the call chain of
   btrfs_start_transaction(). The stack trace is something like the one
   reported in Link tag below:

   general protection fault, probably for non-canonical address 0xdffffc0000000041: 0000 [#1] PREEMPT SMP KASAN
   KASAN: null-ptr-deref in range [0x0000000000000208-0x000000000000020f]
   CPU: 1 PID: 34 Comm: kworker/u4:2 Not tainted 6.1.0-syzkaller-13872-gb6bb9676f216 #0
   Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
   Workqueue: btrfs-qgroup-rescan btrfs_work_helper
   RIP: 0010:start_transaction+0x48/0x10f0 fs/btrfs/transaction.c:564
   Code: 48 89 fb 48 (...)
   RSP: 0018:ffffc90000ab7ab0 EFLAGS: 00010206
   RAX: 0000000000000041 RBX: 0000000000000208 RCX: ffff88801779ba80
   RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
   RBP: dffffc0000000000 R08: 0000000000000001 R09: fffff52000156f5d
   R10: fffff52000156f5d R11: 1ffff92000156f5c R12: 0000000000000000
   R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000003
   FS:  0000000000000000(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
   CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
   CR2: 00007f2bea75b718 CR3: 000000001d0cc000 CR4: 00000000003506e0
   DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
   DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
   Call Trace:
    <TASK>
    btrfs_qgroup_rescan_worker+0x3bb/0x6a0 fs/btrfs/qgroup.c:3402
    btrfs_work_helper+0x312/0x850 fs/btrfs/async-thread.c:280
    process_one_work+0x877/0xdb0 kernel/workqueue.c:2289
    worker_thread+0xb14/0x1330 kernel/workqueue.c:2436
    kthread+0x266/0x300 kernel/kthread.c:376
    ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
    </TASK>
   Modules linked in:

So fix this by having the rescan worker function not attempt to start a
transaction if it didn't do any rescan work.

Reported-by: syzbot+96977faa68092ad382c4@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/000000000000e5454b05f065a803@google.com/
Fixes: e804861bd4e6 ("btrfs: fix deadlock between quota disable and qgroup rescan worker")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: fix invalid leaf access due to inline extent during lseek
Filipe Manana [Thu, 12 Jan 2023 14:17:20 +0000 (14:17 +0000)]
btrfs: fix invalid leaf access due to inline extent during lseek

commit 1f55ee6d0901d915801618bda0af4e5b937e3db7 upstream.

During lseek, for SEEK_DATA and SEEK_HOLE modes, we access the disk_bytenr
of an extent without checking its type. However inline extents have their
data starting the offset of the disk_bytenr field, so accessing that field
when we have an inline extent can result in either of the following:

1) Interpret the inline extent's data as a disk_bytenr value;

2) In case the inline data is less than 8 bytes, we access part of some
   other item in the leaf, or unused space in the leaf;

3) In case the inline data is less than 8 bytes and the extent item is
   the first item in the leaf, we can access beyond the leaf's limit.

So fix this by not accessing the disk_bytenr field if we have an inline
extent.

Fixes: b6e833567ea1 ("btrfs: make hole and data seeking a lot more efficient")
Reported-by: Matthias Schoepfer <matthias.schoepfer@googlemail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216908
Link: https://lore.kernel.org/linux-btrfs/7f25442f-b121-2a3a-5a3d-22bcaae83cd4@leemhuis.info/
CC: stable@vger.kernel.org # 6.1
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: qgroup: do not warn on record without old_roots populated
Qu Wenruo [Tue, 10 Jan 2023 07:14:17 +0000 (15:14 +0800)]
btrfs: qgroup: do not warn on record without old_roots populated

commit 75181406b4eafacc531ff2ee5fb032bd93317e2b upstream.

[BUG]
There are some reports from the mailing list that since v6.1 kernel, the
WARN_ON() inside btrfs_qgroup_account_extent() gets triggered during
rescan:

  WARNING: CPU: 3 PID: 6424 at fs/btrfs/qgroup.c:2756 btrfs_qgroup_account_extents+0x1ae/0x260 [btrfs]
  CPU: 3 PID: 6424 Comm: snapperd Tainted: P           OE      6.1.2-1-default #1 openSUSE Tumbleweed 05c7a1b1b61d5627475528f71f50444637b5aad7
  RIP: 0010:btrfs_qgroup_account_extents+0x1ae/0x260 [btrfs]
  Call Trace:
   <TASK>
  btrfs_commit_transaction+0x30c/0xb40 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6]
   ? start_transaction+0xc3/0x5b0 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6]
  btrfs_qgroup_rescan+0x42/0xc0 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6]
   btrfs_ioctl+0x1ab9/0x25c0 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6]
   ? __rseq_handle_notify_resume+0xa9/0x4a0
   ? mntput_no_expire+0x4a/0x240
   ? __seccomp_filter+0x319/0x4d0
   __x64_sys_ioctl+0x90/0xd0
   do_syscall_64+0x5b/0x80
   ? syscall_exit_to_user_mode+0x17/0x40
   ? do_syscall_64+0x67/0x80
  entry_SYSCALL_64_after_hwframe+0x63/0xcd
  RIP: 0033:0x7fd9b790d9bf
   </TASK>

[CAUSE]
Since commit e15e9f43c7ca ("btrfs: introduce
BTRFS_QGROUP_RUNTIME_FLAG_NO_ACCOUNTING to skip qgroup accounting"), if
our qgroup is already in inconsistent state, we will no longer do the
time-consuming backref walk.

This can leave some qgroup records without a valid old_roots ulist.
Normally this is fine, as btrfs_qgroup_account_extents() would also skip
those records if we have NO_ACCOUNTING flag set.

But there is a small window, if we have NO_ACCOUNTING flag set, and
inserted some qgroup_record without a old_roots ulist, but then the user
triggered a qgroup rescan.

During btrfs_qgroup_rescan(), we firstly clear NO_ACCOUNTING flag, then
commit current transaction.

And since we have a qgroup_record with old_roots = NULL, we trigger the
WARN_ON() during btrfs_qgroup_account_extents().

[FIX]
Unfortunately due to the introduction of NO_ACCOUNTING flag, the
assumption that every qgroup_record would have its old_roots populated
is no longer correct.

Fix the false alerts and drop the WARN_ON().

Reported-by: Lukas Straub <lukasstraub2@web.de>
Reported-by: HanatoK <summersnow9403@gmail.com>
Fixes: e15e9f43c7ca ("btrfs: introduce BTRFS_QGROUP_RUNTIME_FLAG_NO_ACCOUNTING to skip qgroup accounting")
CC: stable@vger.kernel.org # 6.1
Link: https://lore.kernel.org/linux-btrfs/2403c697-ddaf-58ad-3829-0335fc89df09@gmail.com/
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: do not abort transaction on failure to update log root
Filipe Manana [Tue, 10 Jan 2023 14:56:38 +0000 (14:56 +0000)]
btrfs: do not abort transaction on failure to update log root

commit 09e44868f1e03c7825ca4283256abedc95e249a3 upstream.

When syncing a log, if we fail to update a log root in the log root tree,
we are aborting the transaction if the failure was not -ENOSPC. This is
excessive because there is a chance that a transaction commit can succeed,
and therefore avoid to turn the filesystem into RO mode. All we need to be
careful about is to mark the log for a full commit, which we already do,
to make sure no one commits a super block pointing to an outdated log root
tree.

So don't abort the transaction if we fail to update a log root in the log
root tree, and log an error if the failure is not -ENOSPC, so that it does
not go completely unnoticed.

CC: stable@vger.kernel.org # 6.0+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: do not abort transaction on failure to write log tree when syncing log
Filipe Manana [Tue, 10 Jan 2023 14:56:37 +0000 (14:56 +0000)]
btrfs: do not abort transaction on failure to write log tree when syncing log

commit 16199ad9eb6db60a6b10794a09fc1ac6d09312ff upstream.

When syncing the log, if we fail to write log tree extent buffers, we mark
the log for a full commit and abort the transaction. However we don't need
to abort the transaction, all we really need to do is to make sure no one
can commit a superblock pointing to new log tree roots. Just because we
got a failure writing extent buffers for a log tree, it does not mean we
will also fail to do a transaction commit.

One particular case is if due to a bug somewhere, when writing log tree
extent buffers, the tree checker detects some corruption and the writeout
fails because of that. Aborting the transaction can be very disruptive for
a user, specially if the issue happened on a root filesystem. One example
is the scenario in the Link tag below, where an isolated corruption on log
tree leaves was causing transaction aborts when syncing the log.

Link: https://lore.kernel.org/linux-btrfs/ae169fc6-f504-28f0-a098-6fa6a4dfb612@leemhuis.info/
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: add missing setup of log for full commit at add_conflicting_inode()
Filipe Manana [Tue, 10 Jan 2023 14:56:36 +0000 (14:56 +0000)]
btrfs: add missing setup of log for full commit at add_conflicting_inode()

commit 94cd63ae679973edeb5ea95ec25a54467c3e54c8 upstream.

When logging conflicting inodes, if we reach the maximum limit of inodes,
we return BTRFS_LOG_FORCE_COMMIT to force a transaction commit. However
we don't mark the log for full commit (with btrfs_set_log_full_commit()),
which means that once we leave the log transaction and before we commit
the transaction, some other task may sync the log, which is incomplete
as we have not logged all conflicting inodes, leading to some inconsistent
in case that log ends up being replayed.

So also call btrfs_set_log_full_commit() at add_conflicting_inode().

Fixes: e09d94c9e448 ("btrfs: log conflicting inodes without holding log mutex of the initial inode")
CC: stable@vger.kernel.org # 6.1
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: fix directory logging due to race with concurrent index key deletion
Filipe Manana [Tue, 10 Jan 2023 14:56:35 +0000 (14:56 +0000)]
btrfs: fix directory logging due to race with concurrent index key deletion

commit 8bb6898da6271d82d8e76d8088d66b971a7dcfa6 upstream.

Sometimes we log a directory without holding its VFS lock, so while we
logging it, dir index entries may be added or removed. This typically
happens when logging a dentry from a parent directory that points to a
new directory, through log_new_dir_dentries(), or when while logging
some other inode we also need to log its parent directories (through
btrfs_log_all_parents()).

This means that while we are at log_dir_items(), we may not find a dir
index key we found before, because it was deleted in the meanwhile, so
a call to btrfs_search_slot() may return 1 (key not found). In that case
we return from log_dir_items() with a success value (the variable 'err'
has a value of 0). This can lead to a few problems, specially in the case
where the variable 'last_offset' has a value of (u64)-1 (and it's
initialized to that when it was declared):

1) By returning from log_dir_items() with success (0) and a value of
   (u64)-1 for '*last_offset_ret', we end up not logging any other dir
   index keys that follow the missing, just deleted, index key. The
   (u64)-1 value makes log_directory_changes() not call log_dir_items()
   again;

2) Before returning with success (0), log_dir_items(), will log a dir
   index range item covering a range from the last old dentry index
   (stored in the variable 'last_old_dentry_offset') to the value of
   'last_offset'. If 'last_offset' has a value of (u64)-1, then it means
   if the log is persisted and replayed after a power failure, it will
   cause deletion of all the directory entries that have an index number
   between last_old_dentry_offset + 1 and (u64)-1;

3) We can end up returning from log_dir_items() with
   ctx->last_dir_item_offset having a lower value than
   inode->last_dir_index_offset, because the former is set to the current
   key we are processing at process_dir_items_leaf(), and at the end of
   log_directory_changes() we set inode->last_dir_index_offset to the
   current value of ctx->last_dir_item_offset. So if for example a
   deletion of a lower dir index key happened, we set
   ctx->last_dir_item_offset to that index value, then if we return from
   log_dir_items() because btrfs_search_slot() returned 1, we end up
   returning from log_dir_items() with success (0) and then
   log_directory_changes() sets inode->last_dir_index_offset to a lower
   value than it had before.
   This can result in unpredictable and unexpected behaviour when we
   need to log again the directory in the same transaction, and can result
   in ending up with a log tree leaf that has duplicated keys, as we do
   batch insertions of dir index keys into a log tree.

So fix this by making log_dir_items() move on to the next dir index key
if it does not find the one it was looking for.

Reported-by: David Arendt <admin@prnet.org>
Link: https://lore.kernel.org/linux-btrfs/ae169fc6-f504-28f0-a098-6fa6a4dfb612@leemhuis.info/
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: fix missing error handling when logging directory items
Filipe Manana [Tue, 10 Jan 2023 14:56:34 +0000 (14:56 +0000)]
btrfs: fix missing error handling when logging directory items

commit 6d3d970b2735b967650d319be27268fedc5598d1 upstream.

When logging a directory, at log_dir_items(), if we get an error when
attempting to search the subvolume tree for a dir index item, we end up
returning 0 (success) from log_dir_items() because 'err' is left with a
value of 0.

This can lead to a few problems, specially in the case the variable
'last_offset' has a value of (u64)-1 (and it's initialized to that when
it was declared):

1) By returning from log_dir_items() with success (0) and a value of
   (u64)-1 for '*last_offset_ret', we end up not logging any other dir
   index keys that follow the missing, just deleted, index key. The
   (u64)-1 value makes log_directory_changes() not call log_dir_items()
   again;

2) Before returning with success (0), log_dir_items(), will log a dir
   index range item covering a range from the last old dentry index
   (stored in the variable 'last_old_dentry_offset') to the value of
   'last_offset'. If 'last_offset' has a value of (u64)-1, then it means
   if the log is persisted and replayed after a power failure, it will
   cause deletion of all the directory entries that have an index number
   between last_old_dentry_offset + 1 and (u64)-1;

3) We can end up returning from log_dir_items() with
   ctx->last_dir_item_offset having a lower value than
   inode->last_dir_index_offset, because the former is set to the current
   key we are processing at process_dir_items_leaf(), and at the end of
   log_directory_changes() we set inode->last_dir_index_offset to the
   current value of ctx->last_dir_item_offset. So if for example a
   deletion of a lower dir index key happened, we set
   ctx->last_dir_item_offset to that index value, then if we return from
   log_dir_items() because btrfs_search_slot() returned an error, we end up
   returning without any error from log_dir_items() and then
   log_directory_changes() sets inode->last_dir_index_offset to a lower
   value than it had before.
   This can result in unpredictable and unexpected behaviour when we
   need to log again the directory in the same transaction, and can result
   in ending up with a log tree leaf that has duplicated keys, as we do
   batch insertions of dir index keys into a log tree.

Fix this by setting 'err' to the value of 'ret' in case
btrfs_search_slot() or btrfs_previous_item() returned an error. That will
result in falling back to a full transaction commit.

Reported-by: David Arendt <admin@prnet.org>
Link: https://lore.kernel.org/linux-btrfs/ae169fc6-f504-28f0-a098-6fa6a4dfb612@leemhuis.info/
Fixes: e02119d5a7b4 ("Btrfs: Add a write ahead tree log to optimize synchronous operations")
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agobtrfs: add extra error messages to cover non-ENOMEM errors from device_add_list()
Qu Wenruo [Mon, 12 Dec 2022 02:19:37 +0000 (10:19 +0800)]
btrfs: add extra error messages to cover non-ENOMEM errors from device_add_list()

commit ed02363fbbed52a3f5ea0d188edd09045a806eb5 upstream.

[BUG]
When test case btrfs/219 (aka, mount a registered device but with a lower
generation) failed, there is not any useful information for the end user
to find out what's going wrong.

The mount failure just looks like this:

  #  mount -o loop /tmp/219.img2 /mnt/btrfs/
  mount: /mnt/btrfs: mount(2) system call failed: File exists.
         dmesg(1) may have more information after failed mount system call.

While the dmesg contains nothing but the loop device change:

  loop1: detected capacity change from 0 to 524288

[CAUSE]
In device_list_add() we have a lot of extra checks to reject invalid
cases.

That function also contains the regular device scan result like the
following prompt:

  BTRFS: device fsid 6222333e-f9f1-47e6-b306-55ddd4dcaef4 devid 1 transid 8 /dev/loop0 scanned by systemd-udevd (3027)

But unfortunately not all errors have their own error messages, thus if
we hit something wrong in device_add_list(), there may be no error
messages at all.

[FIX]
Add errors message for all non-ENOMEM errors.

For ENOMEM, I'd say we're in a much worse situation, and there should be
some OOM messages way before our call sites.

CC: stable@vger.kernel.org # 6.0+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomm/MADV_COLLAPSE: don't expand collapse when vm_end is past requested end
Zach O'Keefe [Sat, 24 Dec 2022 08:20:34 +0000 (00:20 -0800)]
mm/MADV_COLLAPSE: don't expand collapse when vm_end is past requested end

commit 52dc031088f00e323140ece4004e70c33153c6dd upstream.

MADV_COLLAPSE acts on one hugepage-aligned/sized region at a time, until
it has collapsed all eligible memory contained within the bounds supplied
by the user.

At the top of each hugepage iteration we (re)lock mmap_lock and
(re)validate the VMA for eligibility and update variables that might have
changed while mmap_lock was dropped.  One thing that might occur is that
the VMA could be resized, and as such, we refetch vma->vm_end to make sure
we don't collapse past the end of the VMA's new end.

However, it's possible that when refetching vma->vm_end that we expand the
region acted on by MADV_COLLAPSE if vma->vm_end is greater than size+len
supplied by the user.

The consequence here is that we may attempt to collapse more memory than
requested, possibly yielding either "too much success" or "false failure"
user-visible results.  An example of the former is if we MADV_COLLAPSE the
first 4MiB of a 2TiB mmap()'d file, the incorrect refetch would cause the
operation to block for much longer than anticipated as we attempt to
collapse the entire TiB region.  An example of the latter is that applying
MADV_COLLPSE to a 4MiB file mapped to the start of a 6MiB VMA will
successfully collapse the first 4MiB, then incorrectly attempt to collapse
the last hugepage-aligned/sized region -- fail (since readahead/page cache
lookup will fail) -- and report a failure to the user.

I don't believe there is a kernel stability concern here as we always
(re)validate the VMA / region accordingly.  Also as Hugh mentions, the
user-visible effects are: we try to collapse more memory than requested
by the user, and/or failing an operation that should have otherwise
succeeded.  An example is trying to collapse a 4MiB file contained
within a 12MiB VMA.

Don't expand the acted-on region when refetching vma->vm_end.

Link: https://lkml.kernel.org/r/20221224082035.3197140-1-zokeefe@google.com
Fixes: 4d24de9425f7 ("mm: MADV_COLLAPSE: refetch vm_end after reacquiring mmap_lock")
Signed-off-by: Zach O'Keefe <zokeefe@google.com>
Reported-by: Hugh Dickins <hughd@google.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomm/userfaultfd: enable writenotify while userfaultfd-wp is enabled for a VMA
David Hildenbrand [Fri, 9 Dec 2022 08:09:12 +0000 (09:09 +0100)]
mm/userfaultfd: enable writenotify while userfaultfd-wp is enabled for a VMA

commit 51d3d5eb74ff53b92dcff48b30ae2ed8edd85a32 upstream.

Currently, we don't enable writenotify when enabling userfaultfd-wp on a
shared writable mapping (for now only shmem and hugetlb).  The consequence
is that vma->vm_page_prot will still include write permissions, to be set
as default for all PTEs that get remapped (e.g., mprotect(), NUMA hinting,
page migration, ...).

So far, vma->vm_page_prot is assumed to be a safe default, meaning that we
only add permissions (e.g., mkwrite) but not remove permissions (e.g.,
wrprotect).  For example, when enabling softdirty tracking, we enable
writenotify.  With uffd-wp on shared mappings, that changed.  More details
on vma->vm_page_prot semantics were summarized in [1].

This is problematic for uffd-wp: we'd have to manually check for a uffd-wp
PTEs/PMDs and manually write-protect PTEs/PMDs, which is error prone.
Prone to such issues is any code that uses vma->vm_page_prot to set PTE
permissions: primarily pte_modify() and mk_pte().

Instead, let's enable writenotify such that PTEs/PMDs/...  will be mapped
write-protected as default and we will only allow selected PTEs that are
definitely safe to be mapped without write-protection (see
can_change_pte_writable()) to be writable.  In the future, we might want
to enable write-bit recovery -- e.g., can_change_pte_writable() -- at more
locations, for example, also when removing uffd-wp protection.

This fixes two known cases:

(a) remove_migration_pte() mapping uffd-wp'ed PTEs writable, resulting
    in uffd-wp not triggering on write access.
(b) do_numa_page() / do_huge_pmd_numa_page() mapping uffd-wp'ed PTEs/PMDs
    writable, resulting in uffd-wp not triggering on write access.

Note that do_numa_page() / do_huge_pmd_numa_page() can be reached even
without NUMA hinting (which currently doesn't seem to be applicable to
shmem), for example, by using uffd-wp with a PROT_WRITE shmem VMA.  On
such a VMA, userfaultfd-wp is currently non-functional.

Note that when enabling userfaultfd-wp, there is no need to walk page
tables to enforce the new default protection for the PTEs: we know that
they cannot be uffd-wp'ed yet, because that can only happen after enabling
uffd-wp for the VMA in general.

Also note that this makes mprotect() on ranges with uffd-wp'ed PTEs not
accidentally set the write bit -- which would result in uffd-wp not
triggering on later write access.  This commit makes uffd-wp on shmem
behave just like uffd-wp on anonymous memory in that regard, even though,
mixing mprotect with uffd-wp is controversial.

[1] https://lkml.kernel.org/r/92173bad-caa3-6b43-9d1e-9a471fdbc184@redhat.com

Link: https://lkml.kernel.org/r/20221209080912.7968-1-david@redhat.com
Fixes: b1f9e876862d ("mm/uffd: enable write protection for shmem & hugetlbfs")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Ives van Hoorne <ives@codesandbox.io>
Debugged-by: Peter Xu <peterx@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomm/hugetlb: pre-allocate pgtable pages for uffd wr-protects
Peter Xu [Wed, 4 Jan 2023 22:52:05 +0000 (17:52 -0500)]
mm/hugetlb: pre-allocate pgtable pages for uffd wr-protects

commit fed15f1345dc8a7fc8baa81e8b55c3ba010d7f4b upstream.

Userfaultfd-wp uses pte markers to mark wr-protected pages for both shmem
and hugetlb.  Shmem has pre-allocation ready for markers, but hugetlb path
was overlooked.

Doing so by calling huge_pte_alloc() if the initial pgtable walk fails to
find the huge ptep.  It's possible that huge_pte_alloc() can fail with
high memory pressure, in that case stop the loop immediately and fail
silently.  This is not the most ideal solution but it matches with what we
do with shmem meanwhile it avoids the splat in dmesg.

Link: https://lkml.kernel.org/r/20230104225207.1066932-2-peterx@redhat.com
Fixes: 60dfaad65aa9 ("mm/hugetlb: allow uffd wr-protect none ptes")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: James Houghton <jthoughton@google.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: James Houghton <jthoughton@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: <stable@vger.kernel.org> [5.19+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomm/hugetlb: fix uffd-wp handling for migration entries in hugetlb_change_protection()
David Hildenbrand [Thu, 22 Dec 2022 20:55:11 +0000 (21:55 +0100)]
mm/hugetlb: fix uffd-wp handling for migration entries in hugetlb_change_protection()

commit 44f86392bdd165da7e43d3c772aeb1e128ffd6c8 upstream.

We have to update the uffd-wp SWP PTE bit independent of the type of
migration entry.  Currently, if we're unlucky and we want to install/clear
the uffd-wp bit just while we're migrating a read-only mapped hugetlb
page, we would miss to set/clear the uffd-wp bit.

Further, if we're processing a readable-exclusive migration entry and
neither want to set or clear the uffd-wp bit, we could currently end up
losing the uffd-wp bit.  Note that the same would hold for writable
migrating entries, however, having a writable migration entry with the
uffd-wp bit set would already mean that something went wrong.

Note that the change from !is_readable_migration_entry ->
writable_migration_entry is harmless and actually cleaner, as raised by
Miaohe Lin and discussed in [1].

[1] https://lkml.kernel.org/r/90dd6a93-4500-e0de-2bf0-bf522c311b0c@huawei.com

Link: https://lkml.kernel.org/r/20221222205511.675832-3-david@redhat.com
Fixes: 60dfaad65aa9 ("mm/hugetlb: allow uffd wr-protect none ptes")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomm/hugetlb: fix PTE marker handling in hugetlb_change_protection()
David Hildenbrand [Thu, 22 Dec 2022 20:55:10 +0000 (21:55 +0100)]
mm/hugetlb: fix PTE marker handling in hugetlb_change_protection()

commit 0e678153f5be7e6c8d28835f5a678618da4b7a9c upstream.

Patch series "mm/hugetlb: uffd-wp fixes for hugetlb_change_protection()".

Playing with virtio-mem and background snapshots (using uffd-wp) on
hugetlb in QEMU, I managed to trigger a VM_BUG_ON().  Looking into the
details, hugetlb_change_protection() seems to not handle uffd-wp correctly
in all cases.

Patch #1 fixes my test case.  I don't have reproducers for patch #2, as it
requires running into migration entries.

I did not yet check in detail yet if !hugetlb code requires similar care.

This patch (of 2):

There are two problematic cases when stumbling over a PTE marker in
hugetlb_change_protection():

(1) We protect an uffd-wp PTE marker a second time using uffd-wp: we will
    end up in the "!huge_pte_none(pte)" case and mess up the PTE marker.

(2) We unprotect a uffd-wp PTE marker: we will similarly end up in the
    "!huge_pte_none(pte)" case even though we cleared the PTE, because
    the "pte" variable is stale. We'll mess up the PTE marker.

For example, if we later stumble over such a "wrongly modified" PTE marker,
we'll treat it like a present PTE that maps some garbage page.

This can, for example, be triggered by mapping a memfd backed by huge
pages, registering uffd-wp, uffd-wp'ing an unmapped page and (a)
uffd-wp'ing it a second time; or (b) uffd-unprotecting it; or (c)
unregistering uffd-wp. Then, ff we trigger fallocate(FALLOC_FL_PUNCH_HOLE)
on that file range, we will run into a VM_BUG_ON:

[  195.039560] page:00000000ba1f2987 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x0
[  195.039565] flags: 0x7ffffc0001000(reserved|node=0|zone=0|lastcpupid=0x1fffff)
[  195.039568] raw: 0007ffffc0001000 ffffe742c0000008 ffffe742c0000008 0000000000000000
[  195.039569] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[  195.039569] page dumped because: VM_BUG_ON_PAGE(compound && !PageHead(page))
[  195.039573] ------------[ cut here ]------------
[  195.039574] kernel BUG at mm/rmap.c:1346!
[  195.039579] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[  195.039581] CPU: 7 PID: 4777 Comm: qemu-system-x86 Not tainted 6.0.12-200.fc36.x86_64 #1
[  195.039583] Hardware name: LENOVO 20WNS1F81N/20WNS1F81N, BIOS N35ET50W (1.50 ) 09/15/2022
[  195.039584] RIP: 0010:page_remove_rmap+0x45b/0x550
[  195.039588] Code: [...]
[  195.039589] RSP: 0018:ffffbc03c3633ba8 EFLAGS: 00010292
[  195.039591] RAX: 0000000000000040 RBX: ffffe742c0000000 RCX: 0000000000000000
[  195.039592] RDX: 0000000000000002 RSI: ffffffff8e7aac1a RDI: 00000000ffffffff
[  195.039592] RBP: 0000000000000001 R08: 0000000000000000 R09: ffffbc03c3633a08
[  195.039593] R10: 0000000000000003 R11: ffffffff8f146328 R12: ffff9b04c42754b0
[  195.039594] R13: ffffffff8fcc6328 R14: ffffbc03c3633c80 R15: ffff9b0484ab9100
[  195.039595] FS:  00007fc7aaf68640(0000) GS:ffff9b0bbf7c0000(0000) knlGS:0000000000000000
[  195.039596] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  195.039597] CR2: 000055d402c49110 CR3: 0000000159392003 CR4: 0000000000772ee0
[  195.039598] PKRU: 55555554
[  195.039599] Call Trace:
[  195.039600]  <TASK>
[  195.039602]  __unmap_hugepage_range+0x33b/0x7d0
[  195.039605]  unmap_hugepage_range+0x55/0x70
[  195.039608]  hugetlb_vmdelete_list+0x77/0xa0
[  195.039611]  hugetlbfs_fallocate+0x410/0x550
[  195.039612]  ? _raw_spin_unlock_irqrestore+0x23/0x40
[  195.039616]  vfs_fallocate+0x12e/0x360
[  195.039618]  __x64_sys_fallocate+0x40/0x70
[  195.039620]  do_syscall_64+0x58/0x80
[  195.039623]  ? syscall_exit_to_user_mode+0x17/0x40
[  195.039624]  ? do_syscall_64+0x67/0x80
[  195.039626]  entry_SYSCALL_64_after_hwframe+0x63/0xcd
[  195.039628] RIP: 0033:0x7fc7b590651f
[  195.039653] Code: [...]
[  195.039654] RSP: 002b:00007fc7aaf66e70 EFLAGS: 00000293 ORIG_RAX: 000000000000011d
[  195.039655] RAX: ffffffffffffffda RBX: 0000558ef4b7f370 RCX: 00007fc7b590651f
[  195.039656] RDX: 0000000018000000 RSI: 0000000000000003 RDI: 000000000000000c
[  195.039657] RBP: 0000000008000000 R08: 0000000000000000 R09: 0000000000000073
[  195.039658] R10: 0000000008000000 R11: 0000000000000293 R12: 0000000018000000
[  195.039658] R13: 00007fb8bbe00000 R14: 000000000000000c R15: 0000000000001000
[  195.039661]  </TASK>

Fix it by not going into the "!huge_pte_none(pte)" case if we stumble over
an exclusive marker.  spin_unlock() + continue would get the job done.

However, instead, make it clearer that there are no fall-through
statements: we process each case (hwpoison, migration, marker, !none,
none) and then unlock the page table to continue with the next PTE.  Let's
avoid "continue" statements and use a single spin_unlock() at the end.

Link: https://lkml.kernel.org/r/20221222205511.675832-1-david@redhat.com
Link: https://lkml.kernel.org/r/20221222205511.675832-2-david@redhat.com
Fixes: 60dfaad65aa9 ("mm/hugetlb: allow uffd wr-protect none ptes")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agommc: sdhci-esdhc-imx: correct the tuning start tap and step setting
Haibo Chen [Wed, 7 Dec 2022 11:23:15 +0000 (19:23 +0800)]
mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting

commit 1e336aa0c0250ec84c6f16efac40c9f0138e367d upstream.

Current code logic may be impacted by the setting of ROM/Bootloader,
so unmask these bits first, then setting these bits accordingly.

Fixes: 2b16cf326b70 ("mmc: sdhci-esdhc-imx: move tuning static configuration into hwinit function")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221207112315.1812222-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agommc: sunxi-mmc: Fix clock refcount imbalance during unbind
Samuel Holland [Wed, 10 Aug 2022 02:25:09 +0000 (21:25 -0500)]
mmc: sunxi-mmc: Fix clock refcount imbalance during unbind

commit 8509419758f2cc28dd05370385af0d91573b76b4 upstream.

If the controller is suspended by runtime PM, the clock is already
disabled, so do not try to disable it again during removal. Use
pm_runtime_disable() to flush any pending runtime PM transitions.

Fixes: 9a8e1e8cc2c0 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220810022509.43743-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoACPI: PRM: Check whether EFI runtime is available
Ard Biesheuvel [Thu, 12 Jan 2023 13:33:19 +0000 (14:33 +0100)]
ACPI: PRM: Check whether EFI runtime is available

commit 182da6f2b81a78709c58021542fb694f8ed80774 upstream.

The ACPI PRM address space handler calls efi_call_virt_pointer() to
execute PRM firmware code, but doing so is only permitted when the EFI
runtime environment is available. Otherwise, such calls are guaranteed
to result in a crash, and must therefore be avoided.

Given that the EFI runtime services may become unavailable after a crash
occurring in the firmware, we need to check this each time the PRM
address space handler is invoked. If the EFI runtime services were not
available at registration time to being with, don't install the address
space handler at all.

Fixes: cefc7ca46235 ("ACPI: PRM: implement OperationRegion handler for the PlatformRtMechanism subtype")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agocomedi: adv_pci1760: Fix PWM instruction handling
Ian Abbott [Tue, 3 Jan 2023 14:37:54 +0000 (14:37 +0000)]
comedi: adv_pci1760: Fix PWM instruction handling

commit 2efb6edd52dc50273f5e68ad863dd1b1fb2f2d1c upstream.

(Actually, this is fixing the "Read the Current Status" command sent to
the device's outgoing mailbox, but it is only currently used for the PWM
instructions.)

The PCI-1760 is operated mostly by sending commands to a set of Outgoing
Mailbox registers, waiting for the command to complete, and reading the
result from the Incoming Mailbox registers.  One of these commands is
the "Read the Current Status" command.  The number of this command is
0x07 (see the User's Manual for the PCI-1760 at
<https://advdownload.advantech.com/productfile/Downloadfile2/1-11P6653/PCI-1760.pdf>.
The `PCI1760_CMD_GET_STATUS` macro defined in the driver should expand
to this command number 0x07, but unfortunately it currently expands to
0x03.  (Command number 0x03 is not defined in the User's Manual.)
Correct the definition of the `PCI1760_CMD_GET_STATUS` macro to fix it.

This is used by all the PWM subdevice related instructions handled by
`pci1760_pwm_insn_config()` which are probably all broken.  The effect
of sending the undefined command number 0x03 is not known.

Fixes: 14b93bb6bbf0 ("staging: comedi: adv_pci_dio: separate out PCI-1760 support")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20230103143754.17564-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: core: hub: disable autosuspend for TI TUSB8041
Flavio Suligoi [Mon, 19 Dec 2022 12:47:59 +0000 (13:47 +0100)]
usb: core: hub: disable autosuspend for TI TUSB8041

commit 7171b0e261b17de96490adf053b8bb4b00061bcf upstream.

The Texas Instruments TUSB8041 has an autosuspend problem at high
temperature.

If there is not USB traffic, after a couple of ms, the device enters in
autosuspend mode. In this condition the external clock stops working, to
save energy. When the USB activity turns on, ther hub exits the
autosuspend state, the clock starts running again and all works fine.

At ambient temperature all works correctly, but at high temperature,
when the USB activity turns on, the external clock doesn't restart and
the hub disappears from the USB bus.

Disabling the autosuspend mode for this hub solves the issue.

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20221219124759.3207032-1-f.suligoi@asem.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomisc: fastrpc: Fix use-after-free race condition for maps
Ola Jeppsson [Thu, 24 Nov 2022 17:49:41 +0000 (17:49 +0000)]
misc: fastrpc: Fix use-after-free race condition for maps

commit 96b328d119eca7563c1edcc4e1039a62e6370ecb upstream.

It is possible that in between calling fastrpc_map_get() until
map->fl->lock is taken in fastrpc_free_map(), another thread can call
fastrpc_map_lookup() and get a reference to a map that is about to be
deleted.

Rewrite fastrpc_map_get() to only increase the reference count of a map
if it's non-zero. Propagate this to callers so they can know if a map is
about to be deleted.

Fixes this warning:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 5 PID: 10100 at lib/refcount.c:25 refcount_warn_saturate
...
Call trace:
 refcount_warn_saturate
 [fastrpc_map_get inlined]
 [fastrpc_map_lookup inlined]
 fastrpc_map_create
 fastrpc_internal_invoke
 fastrpc_device_ioctl
 __arm64_sys_ioctl
 invoke_syscall

Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method")
Cc: stable <stable@kernel.org>
Signed-off-by: Ola Jeppsson <ola@snap.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221124174941.418450-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomisc: fastrpc: Don't remove map on creater_process and device_release
Abel Vesa [Thu, 24 Nov 2022 17:49:40 +0000 (17:49 +0000)]
misc: fastrpc: Don't remove map on creater_process and device_release

commit 5bb96c8f9268e2fdb0e5321cbc358ee5941efc15 upstream.

Do not remove the map from the list on error path in
fastrpc_init_create_process, instead call fastrpc_map_put, to avoid
use-after-free. Do not remove it on fastrpc_device_release either,
call fastrpc_map_put instead.

The fastrpc_free_map is the only proper place to remove the map.
This is called only after the reference count is 0.

Fixes: b49f6d83e290 ("misc: fastrpc: Fix a possible double free")
Cc: stable <stable@kernel.org>
Co-developed-by: Ola Jeppsson <ola@snap.com>
Signed-off-by: Ola Jeppsson <ola@snap.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221124174941.418450-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomisc: fastrpc: Fix use-after-free and race in fastrpc_map_find
Abel Vesa [Thu, 24 Nov 2022 17:49:39 +0000 (17:49 +0000)]
misc: fastrpc: Fix use-after-free and race in fastrpc_map_find

commit 9446fa1683a7e3937d9970248ced427c1983a1c5 upstream.

Currently, there is a race window between the point when the mutex is
unlocked in fastrpc_map_lookup and the reference count increasing
(fastrpc_map_get) in fastrpc_map_find, which can also lead to
use-after-free.

So lets merge fastrpc_map_find into fastrpc_map_lookup which allows us
to both protect the maps list by also taking the &fl->lock spinlock and
the reference count, since the spinlock will be released only after.
Add take_ref argument to make this suitable for all callers.

Fixes: 8f6c1d8c4f0c ("misc: fastrpc: Add fdlist implementation")
Cc: stable <stable@kernel.org>
Co-developed-by: Ola Jeppsson <ola@snap.com>
Signed-off-by: Ola Jeppsson <ola@snap.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221124174941.418450-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: misc: onboard_hub: Move 'attach' work to the driver
Matthias Kaehlcke [Tue, 10 Jan 2023 17:32:53 +0000 (17:32 +0000)]
usb: misc: onboard_hub: Move 'attach' work to the driver

commit cde37881e2e14590675d0acdfbad408300d9ca95 upstream.

Currently each onboard_hub platform device owns an 'attach' work,
which is scheduled when the device probes. With this deadlocks
have been reported on a Raspberry Pi 3 B+ [1], which has nested
onboard hubs.

The flow of the deadlock is something like this (with the onboard_hub
driver built as a module) [2]:

- USB root hub is instantiated
- core hub driver calls onboard_hub_create_pdevs(), which creates the
  'raw' platform device for the 1st level hub
- 1st level hub is probed by the core hub driver
- core hub driver calls onboard_hub_create_pdevs(), which creates
  the 'raw' platform device for the 2nd level hub

- onboard_hub platform driver is registered
- platform device for 1st level hub is probed
  - schedules 'attach' work
- platform device for 2nd level hub is probed
  - schedules 'attach' work

- onboard_hub USB driver is registered
- device (and parent) lock of hub is held while the device is
  re-probed with the onboard_hub driver

- 'attach' work (running in another thread) calls driver_attach(), which
   blocks on one of the hub device locks

- onboard_hub_destroy_pdevs() is called by the core hub driver when one
  of the hubs is detached
- destroying the pdevs invokes onboard_hub_remove(), which waits for the
  'attach' work to complete
  - waits forever, since the 'attach' work can't acquire the device lock

Use a single work struct for the driver instead of having a work struct
per onboard hub platform driver instance. With that it isn't necessary
to cancel the work in onboard_hub_remove(), which fixes the deadlock.
The work is only cancelled when the driver is unloaded.

[1] https://lore.kernel.org/r/d04bcc45-3471-4417-b30b-5cf9880d785d@i2se.com/
[2] https://lore.kernel.org/all/Y6OrGbqaMy2iVDWB@google.com/

Cc: stable@vger.kernel.org
Fixes: 8bc063641ceb ("usb: misc: Add onboard_usb_hub driver")
Link: https://lore.kernel.org/r/d04bcc45-3471-4417-b30b-5cf9880d785d@i2se.com/
Link: https://lore.kernel.org/all/Y6OrGbqaMy2iVDWB@google.com/
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230110172954.v2.2.I16b51f32db0c32f8a8532900bfe1c70c8572881a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: misc: onboard_hub: Invert driver registration order
Matthias Kaehlcke [Tue, 10 Jan 2023 17:32:52 +0000 (17:32 +0000)]
usb: misc: onboard_hub: Invert driver registration order

commit e5854355d76b8d768cea8e4fc3ce6dfdba25518a upstream.

The onboard_hub 'driver' consists of two drivers, a platform
driver and a USB driver. Currently when the onboard hub driver
is initialized it first registers the platform driver, then the
USB driver. This results in a race condition when the 'attach'
work is executed, which is scheduled when the platform device
is probed. The purpose of fhe 'attach' work is to bind elegible
USB hub devices to the onboard_hub USB driver. This fails if
the work runs before the USB driver has been registered.

Register the USB driver first, then the platform driver. This
increases the chances that the onboard_hub USB devices are probed
before their corresponding platform device, which the USB driver
tries to locate in _probe(). The driver already handles this
situation and defers probing if the onboard hub platform device
doesn't exist yet.

Cc: stable@vger.kernel.org
Fixes: 8bc063641ceb ("usb: misc: Add onboard_usb_hub driver")
Link: https://lore.kernel.org/lkml/Y6W00vQm3jfLflUJ@hovoldconsulting.com/T/#m0d64295f017942fd988f7c53425db302d61952b4
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20230110172954.v2.1.I75494ebee7027a50235ce4b1e930fa73a578fbe2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: misc: iowarrior: fix up header size for USB_DEVICE_ID_CODEMERCS_IOW100
Greg Kroah-Hartman [Fri, 20 Jan 2023 13:53:30 +0000 (14:53 +0100)]
USB: misc: iowarrior: fix up header size for USB_DEVICE_ID_CODEMERCS_IOW100

commit 14ff7460bb58662d86aa50298943cc7d25532e28 upstream.

The USB_DEVICE_ID_CODEMERCS_IOW100 header size was incorrect, it should
be 12, not 13.

Cc: stable <stable@kernel.org>
Fixes: 17a82716587e ("USB: iowarrior: fix up report size handling for some devices")
Reported-by: Christoph Jung <jung@codemercs.com>
Link: https://lore.kernel.org/r/20230120135330.3842518-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agostaging: vchiq_arm: fix enum vchiq_status return types
Arnd Bergmann [Tue, 17 Jan 2023 16:39:32 +0000 (17:39 +0100)]
staging: vchiq_arm: fix enum vchiq_status return types

commit 7d83299351fe7c812c529f5e39fe63b5312e4233 upstream.

gcc-13 notices a type mismatch between function declaration
and definition for a few functions that have been converted
from returning vchiq specific status values to regular error
codes:

drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:662:5: error: conflicting types for 'vchiq_initialise' due to enum/integer mismatch; have 'int(struct vchiq_instance **)' [-Werror=enum-int-mismatch]
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:1411:1: error: conflicting types for 'vchiq_use_internal' due to enum/integer mismatch; have 'int(struct vchiq_state *, struct vchiq_service *, enum USE_TYPE_E)' [-Werror=enum-int-mismatch]
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:1468:1: error: conflicting types for 'vchiq_release_internal' due to enum/integer mismatch; have 'int(struct vchiq_state *, struct vchiq_service *)' [-Werror=enum-int-mismatch]

Change the declarations to match the actual function definition.

Fixes: a9fbd828be7f ("staging: vchiq_arm: drop enum vchiq_status from vchiq_*_internal")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230117163957.1109872-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: serial: option: add Quectel EM05CN modem
Duke Xin(辛安文) [Mon, 16 Jan 2023 02:33:28 +0000 (18:33 -0800)]
USB: serial: option: add Quectel EM05CN modem

commit 71dfd381a7c051f16a61f82fbd38a4cca563bdca upstream.

The EM05CN modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:

"MBIM"  : AT + MBIM + DIAG + NMEA  + MODEM
"RMNET" : AT + DIAG + NMEA + Modem + QMI

The detailed description of the USB configuration for each mode as follows:

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0312 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-CN
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 1 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 2 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0312 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-CN
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: serial: option: add Quectel EM05CN (SG) modem
Duke Xin(辛安文) [Mon, 16 Jan 2023 02:07:27 +0000 (18:07 -0800)]
USB: serial: option: add Quectel EM05CN (SG) modem

commit 1541dd0097c0f8f470e76eddf5120fc55a7e3101 upstream.

The EM05CN (SG) modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:

"MBIM"  : AT + MBIM + DIAG + NMEA  + MODEM
"RMNET" : AT + DIAG + NMEA + Modem + QMI

The detailed description of the USB configuration for each mode as follows:

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0310 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-CN
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 1 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 2 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0310 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-CN
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: serial: option: add Quectel EC200U modem
Ali Mirghasemi [Wed, 28 Dec 2022 11:38:47 +0000 (15:08 +0330)]
USB: serial: option: add Quectel EC200U modem

commit d9bbb15881046bd76f8710c76e26a740eee997ef upstream.

Add support for EC200U modem

0x0901: EC200U - AT + AP + CP + NMEA + DIAG + MOS

usb-device output:
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0901 Rev= 3.18
S: Manufacturer=Android
S: Product=Android
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=400mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 512 Ivl=4096ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 512 Ivl=4096ms
I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Ali Mirghasemi <ali.mirghasemi1376@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: serial: option: add Quectel EM05-G (RS) modem
Duke Xin(辛安文) [Tue, 27 Dec 2022 09:51:27 +0000 (01:51 -0800)]
USB: serial: option: add Quectel EM05-G (RS) modem

commit b72d13977689f0c717444010e108c4f20658dfee upstream.

The EM05-G (RS) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:

"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM"  : MBIM + AT + DIAG + NMEA + Modem

The detailed description of the USB configuration for each mode as follows:

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0314 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0314 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: serial: option: add Quectel EM05-G (CS) modem
Duke Xin(辛安文) [Tue, 27 Dec 2022 09:28:25 +0000 (01:28 -0800)]
USB: serial: option: add Quectel EM05-G (CS) modem

commit bb78654b0b46316dac687fd4b7dc7cce636f46cd upstream.

The EM05-G (CS) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:

"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM"  : MBIM + AT + DIAG + NMEA + Modem

The detailed description of the USB configuration for each mode as follows:

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030C Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030C Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoUSB: serial: option: add Quectel EM05-G (GR) modem
Duke Xin(辛安文) [Tue, 27 Dec 2022 09:44:30 +0000 (01:44 -0800)]
USB: serial: option: add Quectel EM05-G (GR) modem

commit 6c331f32e32ac71eb3e8b93fceda2802d7ecb889 upstream.

The EM05-G (GR) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:

"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM"  : MBIM + AT + DIAG + NMEA + Modem

The detailed description of the USB configuration for each mode as follows:

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0313 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0313 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoprlimit: do_prlimit needs to have a speculation check
Greg Kroah-Hartman [Fri, 20 Jan 2023 10:03:20 +0000 (11:03 +0100)]
prlimit: do_prlimit needs to have a speculation check

commit 739790605705ddcf18f21782b9c99ad7d53a8c11 upstream.

do_prlimit() adds the user-controlled resource value to a pointer that
will subsequently be dereferenced.  In order to help prevent this
codepath from being used as a spectre "gadget" a barrier needs to be
added after checking the range.

Reported-by: Jordy Zomer <jordyzomer@google.com>
Tested-by: Jordy Zomer <jordyzomer@google.com>
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoxhci: Detect lpm incapable xHC USB3 roothub ports from ACPI tables
Mathias Nyman [Mon, 16 Jan 2023 14:22:16 +0000 (16:22 +0200)]
xhci: Detect lpm incapable xHC USB3 roothub ports from ACPI tables

commit 74622f0a81d0c2bcfc39f9192b788124e8c7f0af upstream.

USB3 ports on xHC hosts may have retimers that cause too long
exit latency to work with native USB3 U1/U2 link power management states.

For now only use usb_acpi_port_lpm_incapable() to evaluate if port lpm
should be disabled while setting up the USB3 roothub.

Other ways to identify lpm incapable ports can be added here later if
ACPI _DSM does not exist.

Limit this to Intel hosts for now, this is to my knowledge only
an Intel issue.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: acpi: add helper to check port lpm capability using acpi _DSM
Mathias Nyman [Mon, 16 Jan 2023 14:22:15 +0000 (16:22 +0200)]
usb: acpi: add helper to check port lpm capability using acpi _DSM

commit cd702d18c882d5a4ea44bbdb38edd5d5577ef640 upstream.

Add a helper to evaluate ACPI usb device specific method (_DSM) provided
in case the USB3 port shouldn't enter U1 and U2 link states.

This _DSM was added as port specific retimer configuration may lead to
exit latencies growing beyond U1/U2 exit limits, and OS needs a way to
find which ports can't support U1/U2 link power management states.

This _DSM is also used by windows:
Link: https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/usb-device-specific-method---dsm-
Some patch issues found in testing resolved by Ron Lee

Cc: stable@vger.kernel.org
Tested-by: Ron Lee <ron.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoxhci: Add a flag to disable USB3 lpm on a xhci root port level.
Mathias Nyman [Mon, 16 Jan 2023 14:22:14 +0000 (16:22 +0200)]
xhci: Add a flag to disable USB3 lpm on a xhci root port level.

commit 0522b9a1653048440da5f21747f21e498b9220d1 upstream.

One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.

This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.

Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoxhci: Add update_hub_device override for PCI xHCI hosts
Mathias Nyman [Mon, 16 Jan 2023 14:22:13 +0000 (16:22 +0200)]
xhci: Add update_hub_device override for PCI xHCI hosts

commit 23a3b8d5a2365653fd9bc5a9454d1e7f4facbf85 upstream.

Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.

This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.

Usb core calls the host update_hub_device once it creates a hub.

Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoxhci: Fix null pointer dereference when host dies
Mathias Nyman [Mon, 16 Jan 2023 14:22:12 +0000 (16:22 +0200)]
xhci: Fix null pointer dereference when host dies

commit a2bc47c43e70cf904b1af49f76d572326c08bca7 upstream.

Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race
and cause null pointer dereference when host suddenly dies.

Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id]
virt device at the same time that xhci_kill_endpoint_urbs() tries to
loop through all the device's endpoints, checking if there are any
cancelled urbs left to give back.

hold the xhci spinlock while freeing the virt device

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agousb: xhci: Check endpoint is valid before dereferencing it
Jimmy Hu [Mon, 16 Jan 2023 14:22:11 +0000 (16:22 +0200)]
usb: xhci: Check endpoint is valid before dereferencing it

commit e8fb5bc76eb86437ab87002d4a36d6da02165654 upstream.

When the host controller is not responding, all URBs queued to all
endpoints need to be killed. This can cause a kernel panic if we
dereference an invalid endpoint.

Fix this by using xhci_get_virt_ep() helper to find the endpoint and
checking if the endpoint is valid before dereferencing it.

[233311.853271] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[233311.853393] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8

[233311.853964] pc : xhci_hc_died+0x10c/0x270
[233311.853971] lr : xhci_hc_died+0x1ac/0x270

[233311.854077] Call trace:
[233311.854085]  xhci_hc_died+0x10c/0x270
[233311.854093]  xhci_stop_endpoint_command_watchdog+0x100/0x1a4
[233311.854105]  call_timer_fn+0x50/0x2d4
[233311.854112]  expire_timers+0xac/0x2e4
[233311.854118]  run_timer_softirq+0x300/0xabc
[233311.854127]  __do_softirq+0x148/0x528
[233311.854135]  irq_exit+0x194/0x1a8
[233311.854143]  __handle_domain_irq+0x164/0x1d0
[233311.854149]  gic_handle_irq.22273+0x10c/0x188
[233311.854156]  el1_irq+0xfc/0x1a8
[233311.854175]  lpm_cpuidle_enter+0x25c/0x418 [msm_pm]
[233311.854185]  cpuidle_enter_state+0x1f0/0x764
[233311.854194]  do_idle+0x594/0x6ac
[233311.854201]  cpu_startup_entry+0x7c/0x80
[233311.854209]  secondary_start_kernel+0x170/0x198

Fixes: 50e8725e7c42 ("xhci: Refactor command watchdog and fix split string.")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <0fe978ed-8269-9774-1c40-f8a98c17e838@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoxhci-pci: set the dma max_seg_size
Ricardo Ribalda [Mon, 16 Jan 2023 14:22:10 +0000 (16:22 +0200)]
xhci-pci: set the dma max_seg_size

commit 93915a4170e9defd56a767a18e6c4076f3d18609 upstream.

Allow devices to have dma operations beyond 64K, and avoid warnings such
as:

xhci_hcd 0000:00:14.0: mapping sg segment longer than device claims to support [len=98304] [max=65536]

Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoRevert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"
Greg Kroah-Hartman [Fri, 20 Jan 2023 10:16:59 +0000 (11:16 +0100)]
Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"

commit 2cbafffbf69addd7509072f4be5917f81d238cf6 upstream.

This reverts commit f24771b62a83239f0dce816bddf0f6807f436235 as it is
reported to break the build.

Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202301200130.ttBiTzfO-lkp@intel.com
Fixes: f24771b62a83 ("serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler")
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Valentin Caron <valentin.caron@foss.st.com> # V3
Cc: Marek Vasut <marex@denx.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoserial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
Marek Vasut [Thu, 12 Jan 2023 18:04:17 +0000 (19:04 +0100)]
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler

commit f24771b62a83239f0dce816bddf0f6807f436235 upstream.

Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.

Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.

Fixes: e359b4411c283 ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230112180417.25595-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma
Hugh Dickins [Thu, 22 Dec 2022 20:41:50 +0000 (12:41 -0800)]
mm/khugepaged: fix collapse_pte_mapped_thp() to allow anon_vma

commit ab0c3f1251b4670978fde0bd54161795a139b060 upstream.

uprobe_write_opcode() uses collapse_pte_mapped_thp() to restore huge pmd,
when removing a breakpoint from hugepage text: vma->anon_vma is always set
in that case, so undo the prohibition.  And MADV_COLLAPSE ought to be able
to collapse some page tables in a vma which happens to have anon_vma set
from CoWing elsewhere.

Is anon_vma lock required?  Almost not: if any page other than expected
subpage of the non-anon huge page is found in the page table, collapse is
aborted without making any change.  However, it is possible that an anon
page was CoWed from this extent in another mm or vma, in which case a
concurrent lookup might look here: so keep it away while clearing pmd (but
perhaps we shall go back to using pmd_lock() there in future).

Note that collapse_pte_mapped_thp() is exceptional in freeing a page table
without having cleared its ptes: I'm uneasy about that, and had thought
pte_clear()ing appropriate; but exclusive i_mmap lock does fix the
problem, and we would have to move the mmu_notification if clearing those
ptes.

What this fixes is not a dangerous instability.  But I suggest Cc stable
because uprobes "healing" has regressed in that way, so this should follow
8d3c106e19e8 into those stable releases where it was backported (and may
want adjustment there - I'll supply backports as needed).

Link: https://lkml.kernel.org/r/b740c9fb-edba-92ba-59fb-7a5592e5dfc@google.com
Fixes: 8d3c106e19e8 ("mm/khugepaged: take the right locks for page table retraction")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zach O'Keefe <zokeefe@google.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agohugetlb: unshare some PMDs when splitting VMAs
James Houghton [Wed, 4 Jan 2023 23:19:10 +0000 (23:19 +0000)]
hugetlb: unshare some PMDs when splitting VMAs

commit b30c14cd61025eeea2f2e8569606cd167ba9ad2d upstream.

PMD sharing can only be done in PUD_SIZE-aligned pieces of VMAs; however,
it is possible that HugeTLB VMAs are split without unsharing the PMDs
first.

Without this fix, it is possible to hit the uffd-wp-related WARN_ON_ONCE
in hugetlb_change_protection [1].  The key there is that
hugetlb_unshare_all_pmds will not attempt to unshare PMDs in
non-PUD_SIZE-aligned sections of the VMA.

It might seem ideal to unshare in hugetlb_vm_op_open, but we need to
unshare in both the new and old VMAs, so unsharing in hugetlb_vm_op_split
seems natural.

[1]: https://lore.kernel.org/linux-mm/CADrL8HVeOkj0QH5VZZbRzybNE8CG-tEGFshnA+bG9nMgcWtBSg@mail.gmail.com/

Link: https://lkml.kernel.org/r/20230104231910.1464197-1-jthoughton@google.com
Fixes: 6dfeaff93be1 ("hugetlb/userfaultfd: unshare all pmds for hugetlbfs when register wp")
Signed-off-by: James Houghton <jthoughton@google.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agomm/shmem: restore SHMEM_HUGE_DENY precedence over MADV_COLLAPSE
Zach O'Keefe [Sat, 24 Dec 2022 08:20:35 +0000 (00:20 -0800)]
mm/shmem: restore SHMEM_HUGE_DENY precedence over MADV_COLLAPSE

commit 3de0c269adc6c2fac0bb1fb11965f0de699dc32b upstream.

SHMEM_HUGE_DENY is for emergency use by the admin, to disable allocation
of shmem huge pages if, for example, a dangerous bug is found in their
usage: see "deny" in Documentation/mm/transhuge.rst.  An app using
madvise(,,MADV_COLLAPSE) should not be allowed to override it: restore its
precedence over shmem_huge_force.

Restore SHMEM_HUGE_DENY precedence over MADV_COLLAPSE.

Link: https://lkml.kernel.org/r/20221224082035.3197140-2-zokeefe@google.com
Fixes: 7c6c6cc4d3a2 ("mm/shmem: add flag to enforce shmem THP in hugepage_vma_check()")
Signed-off-by: Zach O'Keefe <zokeefe@google.com>
Suggested-by: Hugh Dickins <hughd@google.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agonilfs2: fix general protection fault in nilfs_btree_insert()
Ryusuke Konishi [Thu, 5 Jan 2023 05:53:56 +0000 (14:53 +0900)]
nilfs2: fix general protection fault in nilfs_btree_insert()

commit 7633355e5c7f29c049a9048e461427d1d8ed3051 upstream.

If nilfs2 reads a corrupted disk image and tries to reads a b-tree node
block by calling __nilfs_btree_get_block() against an invalid virtual
block address, it returns -ENOENT because conversion of the virtual block
address to a disk block address fails.  However, this return value is the
same as the internal code that b-tree lookup routines return to indicate
that the block being searched does not exist, so functions that operate on
that b-tree may misbehave.

When nilfs_btree_insert() receives this spurious 'not found' code from
nilfs_btree_do_lookup(), it misunderstands that the 'not found' check was
successful and continues the insert operation using incomplete lookup path
data, causing the following crash:

 general protection fault, probably for non-canonical address
 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
 KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
 ...
 RIP: 0010:nilfs_btree_get_nonroot_node fs/nilfs2/btree.c:418 [inline]
 RIP: 0010:nilfs_btree_prepare_insert fs/nilfs2/btree.c:1077 [inline]
 RIP: 0010:nilfs_btree_insert+0x6d3/0x1c10 fs/nilfs2/btree.c:1238
 Code: bc 24 80 00 00 00 4c 89 f8 48 c1 e8 03 42 80 3c 28 00 74 08 4c 89
 ff e8 4b 02 92 fe 4d 8b 3f 49 83 c7 28 4c 89 f8 48 c1 e8 03 <42> 80 3c
 28 00 74 08 4c 89 ff e8 2e 02 92 fe 4d 8b 3f 49 83 c7 02
 ...
 Call Trace:
 <TASK>
  nilfs_bmap_do_insert fs/nilfs2/bmap.c:121 [inline]
  nilfs_bmap_insert+0x20d/0x360 fs/nilfs2/bmap.c:147
  nilfs_get_block+0x414/0x8d0 fs/nilfs2/inode.c:101
  __block_write_begin_int+0x54c/0x1a80 fs/buffer.c:1991
  __block_write_begin fs/buffer.c:2041 [inline]
  block_write_begin+0x93/0x1e0 fs/buffer.c:2102
  nilfs_write_begin+0x9c/0x110 fs/nilfs2/inode.c:261
  generic_perform_write+0x2e4/0x5e0 mm/filemap.c:3772
  __generic_file_write_iter+0x176/0x400 mm/filemap.c:3900
  generic_file_write_iter+0xab/0x310 mm/filemap.c:3932
  call_write_iter include/linux/fs.h:2186 [inline]
  new_sync_write fs/read_write.c:491 [inline]
  vfs_write+0x7dc/0xc50 fs/read_write.c:584
  ksys_write+0x177/0x2a0 fs/read_write.c:637
  do_syscall_x64 arch/x86/entry/common.c:50 [inline]
  do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
  entry_SYSCALL_64_after_hwframe+0x63/0xcd
 ...
 </TASK>

This patch fixes the root cause of this problem by replacing the error
code that __nilfs_btree_get_block() returns on block address conversion
failure from -ENOENT to another internal code -EINVAL which means that the
b-tree metadata is corrupted.

By returning -EINVAL, it propagates without glitches, and for all relevant
b-tree operations, functions in the upper bmap layer output an error
message indicating corrupted b-tree metadata via
nilfs_bmap_convert_error(), and code -EIO will be eventually returned as
it should be.

Link: https://lkml.kernel.org/r/000000000000bd89e205f0e38355@google.com
Link: https://lkml.kernel.org/r/20230105055356.8811-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+ede796cecd5296353515@syzkaller.appspotmail.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agozonefs: Detect append writes at invalid locations
Damien Le Moal [Fri, 6 Jan 2023 08:43:06 +0000 (17:43 +0900)]
zonefs: Detect append writes at invalid locations

commit a608da3bd730d718f2d3ebec1c26f9865f8f17ce upstream.

Using REQ_OP_ZONE_APPEND operations for synchronous writes to sequential
files succeeds regardless of the zone write pointer position, as long as
the target zone is not full. This means that if an external (buggy)
application writes to the zone of a sequential file underneath the file
system, subsequent file write() operation will succeed but the file size
will not be correct and the file will contain invalid data written by
another application.

Modify zonefs_file_dio_append() to check the written sector of an append
write (returned in bio->bi_iter.bi_sector) and return -EIO if there is a
mismatch with the file zone wp offset field. This change triggers a call
to zonefs_io_error() and a zone check. Modify zonefs_io_error_cb() to
not expose the unexpected data after the current inode size when the
errors=remount-ro mode is used. Other error modes are correctly handled
already.

Fixes: 02ef12a663c7 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoLoongArch: Add HWCAP_LOONGARCH_CPUCFG to elf_hwcap
Huacai Chen [Tue, 17 Jan 2023 03:42:16 +0000 (11:42 +0800)]
LoongArch: Add HWCAP_LOONGARCH_CPUCFG to elf_hwcap

commit d52fec86a465355b379e839fa372ead0334d62e6 upstream.

HWCAP_LOONGARCH_CPUCFG is missing in elf_hwcap, so add it for glibc's
later use.

Cc: stable@vger.kernel.org
Reported-by: Yinyu Cai <caiyinyu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoAdd exception protection processing for vd in axi_chan_handle_err function
Shawn.Shao [Thu, 12 Jan 2023 05:58:02 +0000 (13:58 +0800)]
Add exception protection processing for vd in axi_chan_handle_err function

commit 57054fe516d59d03a7bcf1888e82479ccc244f87 upstream.

Since there is no protection for vd, a kernel panic will be
triggered here in exceptional cases.

You can refer to the processing of axi_chan_block_xfer_complete function

The triggered kernel panic is as follows:

[   67.848444] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000060
[   67.848447] Mem abort info:
[   67.848449]   ESR = 0x96000004
[   67.848451]   EC = 0x25: DABT (current EL), IL = 32 bits
[   67.848454]   SET = 0, FnV = 0
[   67.848456]   EA = 0, S1PTW = 0
[   67.848458] Data abort info:
[   67.848460]   ISV = 0, ISS = 0x00000004
[   67.848462]   CM = 0, WnR = 0
[   67.848465] user pgtable: 4k pages, 48-bit VAs, pgdp=00000800c4c0b000
[   67.848468] [0000000000000060] pgd=0000000000000000, p4d=0000000000000000
[   67.848472] Internal error: Oops: 96000004 [#1] SMP
[   67.848475] Modules linked in: dmatest
[   67.848479] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.100-emu_x2rc+ #11
[   67.848483] pstate: 62000085 (nZCv daIf -PAN -UAO +TCO BTYPE=--)
[   67.848487] pc : axi_chan_handle_err+0xc4/0x230
[   67.848491] lr : axi_chan_handle_err+0x30/0x230
[   67.848493] sp : ffff0803fe55ae50
[   67.848495] x29: ffff0803fe55ae50 x28: ffff800011212200
[   67.848500] x27: ffff0800c42c0080 x26: ffff0800c097c080
[   67.848504] x25: ffff800010d33880 x24: ffff80001139d850
[   67.848508] x23: ffff0800c097c168 x22: 0000000000000000
[   67.848512] x21: 0000000000000080 x20: 0000000000002000
[   67.848517] x19: ffff0800c097c080 x18: 0000000000000000
[   67.848521] x17: 0000000000000000 x16: 0000000000000000
[   67.848525] x15: 0000000000000000 x14: 0000000000000000
[   67.848529] x13: 0000000000000000 x12: 0000000000000040
[   67.848533] x11: ffff0800c0400248 x10: ffff0800c040024a
[   67.848538] x9 : ffff800010576cd4 x8 : ffff0800c0400270
[   67.848542] x7 : 0000000000000000 x6 : ffff0800c04003e0
[   67.848546] x5 : ffff0800c0400248 x4 : ffff0800c4294480
[   67.848550] x3 : dead000000000100 x2 : dead000000000122
[   67.848555] x1 : 0000000000000100 x0 : ffff0800c097c168
[   67.848559] Call trace:
[   67.848562]  axi_chan_handle_err+0xc4/0x230
[   67.848566]  dw_axi_dma_interrupt+0xf4/0x590
[   67.848569]  __handle_irq_event_percpu+0x60/0x220
[   67.848573]  handle_irq_event+0x64/0x120
[   67.848576]  handle_fasteoi_irq+0xc4/0x220
[   67.848580]  __handle_domain_irq+0x80/0xe0
[   67.848583]  gic_handle_irq+0xc0/0x138
[   67.848585]  el1_irq+0xc8/0x180
[   67.848588]  arch_cpu_idle+0x14/0x2c
[   67.848591]  default_idle_call+0x40/0x16c
[   67.848594]  do_idle+0x1f0/0x250
[   67.848597]  cpu_startup_entry+0x2c/0x60
[   67.848600]  rest_init+0xc0/0xcc
[   67.848603]  arch_call_rest_init+0x14/0x1c
[   67.848606]  start_kernel+0x4cc/0x500
[   67.848610] Code: eb0002ff 9a9f12d6 f2fbd5a2 f2fbd5a3 (a94602c1)
[   67.848613] ---[ end trace 585a97036f88203a ]---

Signed-off-by: Shawn.Shao <shawn.shao@jaguarmicro.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230112055802.1764-1-shawn.shao@jaguarmicro.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoproc: fix PIE proc-empty-vm, proc-pid-vm tests
Alexey Dobriyan [Fri, 6 Jan 2023 19:30:14 +0000 (22:30 +0300)]
proc: fix PIE proc-empty-vm, proc-pid-vm tests

commit 5316a017d093f644675a56523bcf5787ba8f4fef upstream.

vsyscall detection code uses direct call to the beginning of
the vsyscall page:

asm ("call %P0" :: "i" (0xffffffffff600000))

It generates "call rel32" instruction but it is not relocated if binary
is PIE, so binary segfaults into random userspace address and vsyscall
page status is detected incorrectly.

Do more direct:

asm ("call *%rax")

which doesn't do need any relocaltions.

Mark g_vsyscall as volatile for a good measure, I didn't find instruction
setting it to 0. Now the code is obviously correct:

xor eax, eax
mov rdi, rbp
mov rsi, rbp
mov DWORD PTR [rip+0x2d15], eax      # g_vsyscall = 0
mov rax, 0xffffffffff600000
call rax
mov DWORD PTR [rip+0x2d02], 1        # g_vsyscall = 1
mov eax, DWORD PTR ds:0xffffffffff600000
mov DWORD PTR [rip+0x2cf1], 2        # g_vsyscall = 2
mov edi, [rip+0x2ceb]                # exit(g_vsyscall)
call exit

Note: fixed proc-empty-vm test oopses 5.19.0-28-generic kernel
but this is separate story.

Link: https://lkml.kernel.org/r/Y7h2xvzKLg36DSq8@p183
Fixes: 5bc73bb3451b9 ("proc: test how it holds up with mapping'less process")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agonommu: fix split_vma() map_count error
Liam Howlett [Mon, 9 Jan 2023 20:58:20 +0000 (20:58 +0000)]
nommu: fix split_vma() map_count error

commit fd9edbdbdcde6b489ce59f326755ef16a2ffadd7 upstream.

During the maple tree conversion of nommu, an error in counting the VMAs
was introduced by counting the existing VMA again.  The counting used to
be decremented by one and incremented by two, but now it only increments
by two.  Fix the counting error by moving the increment outside the
setup_vma_to_mm() function to the callers.

Link: https://lkml.kernel.org/r/20230109205809.956325-1-Liam.Howlett@oracle.com
Fixes: 8220543df148 ("nommu: remove uses of VMA linked list")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agonommu: fix do_munmap() error path
Liam Howlett [Mon, 9 Jan 2023 20:57:21 +0000 (20:57 +0000)]
nommu: fix do_munmap() error path

commit 80be727ec87225797771a39f3e6801baf291faaf upstream.

When removing a VMA from the tree fails due to no memory, do not free the
VMA since a reference still exists.

Link: https://lkml.kernel.org/r/20230109205708.956103-1-Liam.Howlett@oracle.com
Fixes: 8220543df148 ("nommu: remove uses of VMA linked list")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agonommu: fix memory leak in do_mmap() error path
Liam Howlett [Mon, 9 Jan 2023 20:55:21 +0000 (20:55 +0000)]
nommu: fix memory leak in do_mmap() error path

commit 7f31cced5724e6d414fe750aa1cd7e7b578ec22f upstream.

The preallocation of the maple tree nodes may leak if the error path to
"error_just_free" is taken.  Fix this by moving the freeing of the maple
tree nodes to a shared location for all error paths.

Link: https://lkml.kernel.org/r/20230109205507.955577-1-Liam.Howlett@oracle.com
Fixes: 8220543df148 ("nommu: remove uses of VMA linked list")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agowifi: mac80211: fix initialization of rx->link and rx->link_sta
Felix Fietkau [Fri, 30 Dec 2022 20:07:47 +0000 (21:07 +0100)]
wifi: mac80211: fix initialization of rx->link and rx->link_sta

commit e66b7920aa5ac5b1a1997a454004ba9246a3c005 upstream.

There are some codepaths that do not initialize rx->link_sta properly. This
causes a crash in places which assume that rx->link_sta is valid if rx->sta
is valid.
One known instance is triggered by __ieee80211_rx_h_amsdu being called from
fast-rx. It results in a crash like this one:

 BUG: kernel NULL pointer dereference, address: 00000000000000a8
 #PF: supervisor write access in kernel mode
 #PF: error_code(0x0002) - not-present page PGD 0 P4D 0
 Oops: 0002 [#1] PREEMPT SMP PTI
 CPU: 1 PID: 506 Comm: mt76-usb-rx phy Tainted: G            E      6.1.0-debian64x+1.7 #3
 Hardware name: ZOTAC ZBOX-ID92/ZBOX-IQ01/ZBOX-ID92/ZBOX-IQ01, BIOS B220P007 05/21/2014
 RIP: 0010:ieee80211_deliver_skb+0x62/0x1f0 [mac80211]
 Code: 00 48 89 04 24 e8 9e a7 c3 df 89 c0 48 03 1c c5 a0 ea 39 a1 4c 01 6b 08 48 ff 03 48
       83 7d 28 00 74 11 48 8b 45 30 48 63 55 44 <48> 83 84 d0 a8 00 00 00 01 41 8b 86 c0
       11 00 00 8d 50 fd 83 fa 01
 RSP: 0018:ffff999040803b10 EFLAGS: 00010286
 RAX: 0000000000000000 RBX: ffffb9903f496480 RCX: 0000000000000000
 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
 RBP: ffff999040803ce0 R08: 0000000000000000 R09: 0000000000000000
 R10: 0000000000000000 R11: 0000000000000000 R12: ffff8d21828ac900
 R13: 000000000000004a R14: ffff8d2198ed89c0 R15: ffff8d2198ed8000
 FS:  0000000000000000(0000) GS:ffff8d24afe80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00000000000000a8 CR3: 0000000429810002 CR4: 00000000001706e0
 Call Trace:
  <TASK>
  __ieee80211_rx_h_amsdu+0x1b5/0x240 [mac80211]
  ? ieee80211_prepare_and_rx_handle+0xcdd/0x1320 [mac80211]
  ? __local_bh_enable_ip+0x3b/0xa0
  ieee80211_prepare_and_rx_handle+0xcdd/0x1320 [mac80211]
  ? prepare_transfer+0x109/0x1a0 [xhci_hcd]
  ieee80211_rx_list+0xa80/0xda0 [mac80211]
  mt76_rx_complete+0x207/0x2e0 [mt76]
  mt76_rx_poll_complete+0x357/0x5a0 [mt76]
  mt76u_rx_worker+0x4f5/0x600 [mt76_usb]
  ? mt76_get_min_avg_rssi+0x140/0x140 [mt76]
  __mt76_worker_fn+0x50/0x80 [mt76]
  kthread+0xed/0x120
  ? kthread_complete_and_exit+0x20/0x20
  ret_from_fork+0x22/0x30

Since the initialization of rx->link and rx->link_sta is rather convoluted
and duplicated in many places, clean it up by using a helper function to
set it.

Fixes: ccdde7c74ffd ("wifi: mac80211: properly implement MLO key handling")
Fixes: b320d6c456ff ("wifi: mac80211: use correct rx link_sta instead of default")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221230200747.19040-1-nbd@nbd.name
[remove unnecessary rx->sta->sta.mlo check]
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agowifi: mac80211: sdata can be NULL during AMPDU start
Alexander Wetzel [Fri, 30 Dec 2022 12:18:50 +0000 (13:18 +0100)]
wifi: mac80211: sdata can be NULL during AMPDU start

commit 69403bad97aa0162e3d7911b27e25abe774093df upstream.

ieee80211_tx_ba_session_handle_start() may get NULL for sdata when a
deauthentication is ongoing.

Here a trace triggering the race with the hostapd test
multi_ap_fronthaul_on_ap:

(gdb) list *drv_ampdu_action+0x46
0x8b16 is in drv_ampdu_action (net/mac80211/driver-ops.c:396).
391             int ret = -EOPNOTSUPP;
392
393             might_sleep();
394
395             sdata = get_bss_sdata(sdata);
396             if (!check_sdata_in_driver(sdata))
397                     return -EIO;
398
399             trace_drv_ampdu_action(local, sdata, params);
400

wlan0: moving STA 02:00:00:00:03:00 to state 3
wlan0: associated
wlan0: deauthenticating from 02:00:00:00:03:00 by local choice (Reason: 3=DEAUTH_LEAVING)
wlan3.sta1: Open BA session requested for 02:00:00:00:00:00 tid 0
wlan3.sta1: dropped frame to 02:00:00:00:00:00 (unauthorized port)
wlan0: moving STA 02:00:00:00:03:00 to state 2
wlan0: moving STA 02:00:00:00:03:00 to state 1
wlan0: Removed STA 02:00:00:00:03:00
wlan0: Destroyed STA 02:00:00:00:03:00
BUG: unable to handle page fault for address: fffffffffffffb48
PGD 11814067 P4D 11814067 PUD 11816067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 2 PID: 133397 Comm: kworker/u16:1 Tainted: G        W          6.1.0-rc8-wt+ #59
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
Workqueue: phy3 ieee80211_ba_session_work [mac80211]
RIP: 0010:drv_ampdu_action+0x46/0x280 [mac80211]
Code: 53 48 89 f3 be 89 01 00 00 e8 d6 43 bf ef e8 21 46 81 f0 83 bb a0 1b 00 00 04 75 0e 48 8b 9b 28 0d 00 00 48 81 eb 10 0e 00 00 <8b> 93 58 09 00 00 f6 c2 20 0f 84 3b 01 00 00 8b 05 dd 1c 0f 00 85
RSP: 0018:ffffc900025ebd20 EFLAGS: 00010287
RAX: 0000000000000000 RBX: fffffffffffff1f0 RCX: ffff888102228240
RDX: 0000000080000000 RSI: ffffffff918c5de0 RDI: ffff888102228b40
RBP: ffffc900025ebd40 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000000 R12: ffff888118c18ec0
R13: 0000000000000000 R14: ffffc900025ebd60 R15: ffff888018b7efb8
FS:  0000000000000000(0000) GS:ffff88817a600000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: fffffffffffffb48 CR3: 0000000105228006 CR4: 0000000000170ee0
Call Trace:
 <TASK>
 ieee80211_tx_ba_session_handle_start+0xd0/0x190 [mac80211]
 ieee80211_ba_session_work+0xff/0x2e0 [mac80211]
 process_one_work+0x29f/0x620
 worker_thread+0x4d/0x3d0
 ? process_one_work+0x620/0x620
 kthread+0xfb/0x120
 ? kthread_complete_and_exit+0x20/0x20
 ret_from_fork+0x22/0x30
 </TASK>

Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20221230121850.218810-2-alexander@wetzel-home.de
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agowifi: mac80211: reset multiple BSSID options in stop_ap()
Aloka Dixit [Wed, 21 Dec 2022 18:56:16 +0000 (10:56 -0800)]
wifi: mac80211: reset multiple BSSID options in stop_ap()

commit 0eb38842ada035d71bb06fb9116f26f24ee0f998 upstream.

Reset multiple BSSID options when all AP related configurations are
reset in ieee80211_stop_ap().

Stale values result in HWSIM test failures (e.g. p2p_group_cli_invalid),
if run after 'he_ap_ema'.

Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://lore.kernel.org/r/20221221185616.11514-1-quic_alokad@quicinc.com
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agowifi: mac80211: fix MLO + AP_VLAN check
Felix Fietkau [Wed, 14 Dec 2022 13:03:26 +0000 (14:03 +0100)]
wifi: mac80211: fix MLO + AP_VLAN check

commit f216033d770f7ca0eda491fe01a9f02e7af59576 upstream.

Instead of preventing adding AP_VLAN to MLO enabled APs, this check was
preventing adding more than one 4-addr AP_VLAN regardless of the MLO status.
Fix this by adding missing extra checks.

Fixes: ae960ee90bb1 ("wifi: mac80211: prevent VLANs on MLDs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221214130326.37756-1-nbd@nbd.name
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agowifi: brcmfmac: fix regression for Broadcom PCIe wifi devices
Arend van Spriel [Wed, 11 Jan 2023 11:24:19 +0000 (12:24 +0100)]
wifi: brcmfmac: fix regression for Broadcom PCIe wifi devices

commit ed05cb177ae5cd7f02f1d6e7706ba627d30f1696 upstream.

A sanity check was introduced considering maximum flowrings above
256 as insane and effectively aborting the device probe. This
resulted in regression for number of users as the value turns out
to be sane after all.

Fixes: 2aca4f3734bd ("brcmfmac: return error when getting invalid max_flowrings from dongle")
Reported-by: chainofflowers <chainofflowers@posteo.net>
Link: https://lore.kernel.org/all/4781984.GXAFRqVoOG@luna/
Reported-by: Christian Marillat <marillat@debian.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216894
Cc: stable@vger.kernel.org
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230111112419.24185-1-arend.vanspriel@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoBluetooth: hci_qca: Fix driver shutdown on closed serdev
Krzysztof Kozlowski [Thu, 29 Dec 2022 10:28:29 +0000 (11:28 +0100)]
Bluetooth: hci_qca: Fix driver shutdown on closed serdev

commit 272970be3dabd24cbe50e393ffee8f04aec3b9a8 upstream.

The driver shutdown callback (which sends EDL_SOC_RESET to the device
over serdev) should not be invoked when HCI device is not open (e.g. if
hci_dev_open_sync() failed), because the serdev and its TTY are not open
either.  Also skip this step if device is powered off
(qca_power_shutdown()).

The shutdown callback causes use-after-free during system reboot with
Qualcomm Atheros Bluetooth:

  Unable to handle kernel paging request at virtual address
  0072662f67726fd7
  ...
  CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G        W
  6.1.0-rt5-00325-g8a5f56bcfcca #8
  Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
  Call trace:
   tty_driver_flush_buffer+0x4/0x30
   serdev_device_write_flush+0x24/0x34
   qca_serdev_shutdown+0x80/0x130 [hci_uart]
   device_shutdown+0x15c/0x260
   kernel_restart+0x48/0xac

KASAN report:

  BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50
  Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1

  CPU: 7 PID: 1 Comm: systemd-shutdow Not tainted
  6.1.0-next-20221220-00014-gb85aaf97fb01-dirty #28
  Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
  Call trace:
   dump_backtrace.part.0+0xdc/0xf0
   show_stack+0x18/0x30
   dump_stack_lvl+0x68/0x84
   print_report+0x188/0x488
   kasan_report+0xa4/0xf0
   __asan_load8+0x80/0xac
   tty_driver_flush_buffer+0x1c/0x50
   ttyport_write_flush+0x34/0x44
   serdev_device_write_flush+0x48/0x60
   qca_serdev_shutdown+0x124/0x274
   device_shutdown+0x1e8/0x350
   kernel_restart+0x48/0xb0
   __do_sys_reboot+0x244/0x2d0
   __arm64_sys_reboot+0x54/0x70
   invoke_syscall+0x60/0x190
   el0_svc_common.constprop.0+0x7c/0x160
   do_el0_svc+0x44/0xf0
   el0_svc+0x2c/0x6c
   el0t_64_sync_handler+0xbc/0x140
   el0t_64_sync+0x190/0x194

Fixes: 7e7bbddd029b ("Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agoBluetooth: hci_sync: Fix use HCI_OP_LE_READ_BUFFER_SIZE_V2
Luiz Augusto von Dentz [Mon, 19 Dec 2022 21:32:51 +0000 (13:32 -0800)]
Bluetooth: hci_sync: Fix use HCI_OP_LE_READ_BUFFER_SIZE_V2

commit 3a4d29b6d631bb00236a98887e1039bbfc1b6ab5 upstream.

Don't try to use HCI_OP_LE_READ_BUFFER_SIZE_V2 if controller don't
support ISO channels, but in order to check if ISO channels are
supported HCI_OP_LE_READ_LOCAL_FEATURES needs to be done earlier so the
features bits can be checked on hci_le_read_buffer_size_sync.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216817
Fixes: c1631dbc00c1 ("Bluetooth: hci_sync: Fix hci_read_buffer_size_sync")
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
23 months agofbdev: omapfb: avoid stack overflow warning
Arnd Bergmann [Thu, 15 Dec 2022 17:02:28 +0000 (18:02 +0100)]
fbdev: omapfb: avoid stack overflow warning

[ Upstream commit 634cf6ead93988b0da9ac054521ab63a3ba189db ]

The dsi_irq_stats structure is a little too big to fit on the
stack of a 32-bit task, depending on the specific gcc options:

fbdev/omap2/omapfb/dss/dsi.c: In function 'dsi_dump_dsidev_irqs':
fbdev/omap2/omapfb/dss/dsi.c:1621:1: error: the frame size of 1064 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

Since this is only a debugfs file, performance is not critical,
so just dynamically allocate it, and print an error message
in there in place of a failure code when the allocation fails.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
23 months agoof: fdt: Honor CONFIG_CMDLINE* even without /chosen node, take 2
Rob Herring [Tue, 3 Jan 2023 18:00:32 +0000 (12:00 -0600)]
of: fdt: Honor CONFIG_CMDLINE* even without /chosen node, take 2

[ Upstream commit 064e32dc5b03114d0767893fecdaf7b5dfd8c286 ]

I do not read a strict requirement on /chosen node in either ePAPR or in
Documentation/devicetree. Help text for CONFIG_CMDLINE and
CONFIG_CMDLINE_EXTEND doesn't make their behavior explicitly dependent on
the presence of /chosen or the presense of /chosen/bootargs.

However the early check for /chosen and bailing out in
early_init_dt_scan_chosen() skips CONFIG_CMDLINE handling which is not
really related to /chosen node or the particular method of passing cmdline
from bootloader.

This leads to counterintuitive combinations (assuming
CONFIG_CMDLINE_EXTEND=y):

a) bootargs="foo", CONFIG_CMDLINE="bar" => cmdline=="foo bar"
b) /chosen missing, CONFIG_CMDLINE="bar" => cmdline==""
c) bootargs="", CONFIG_CMDLINE="bar" => cmdline==" bar"

Rework early_init_dt_scan_chosen() so that the cmdline config options are
always handled.

[commit msg written by Alexander Sverdlin]

Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Tested-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230103-dt-cmdline-fix-v1-2-7038e88b18b6@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
23 months agoperf/x86/rapl: Add support for Intel Emerald Rapids
Zhang Rui [Wed, 4 Jan 2023 14:58:31 +0000 (22:58 +0800)]
perf/x86/rapl: Add support for Intel Emerald Rapids

[ Upstream commit 57512b57dcfaf63c52d8ad2fb35321328cde31b0 ]

Emerald Rapids RAPL support is the same as previous Sapphire Rapids.
Add Emerald Rapids model for RAPL.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230104145831.25498-2-rui.zhang@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
23 months agoperf/x86/rapl: Add support for Intel Meteor Lake
Zhang Rui [Wed, 4 Jan 2023 14:58:30 +0000 (22:58 +0800)]
perf/x86/rapl: Add support for Intel Meteor Lake

[ Upstream commit f52853a668bfeddd79f319d536a506f68cc2b478 ]

Meteor Lake RAPL support is the same as previous Sky Lake.
Add Meteor Lake model for RAPL.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230104145831.25498-1-rui.zhang@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>